Mirella Instructions Part 2

8/6/2019 Mirella Instructions Part 2

1/4

I i

ACCESSORIES

\lib~

~0~

~~~~ @@

"~

61 1 ' 11 1 , I

" LIST OF ACCESSORIES.,,~

.1) Accessory box2) Case with needles3) Pl astic oiler

8) Fastening screws forstraight guide

9) Embroidery plate10) HemmerI I) Straight guide12) Quilter13) Darning foot.

7) Bobbins (3)< .

t< . .~ 4) Screw driver (mediumsize)

" "

5) Screw driver (smallsize)

j,6) Hand crank

. ~,

;, RE CO MMENDED NEEDL E AND THREAD SIZES

~

S iz es of th read S i zes of ne edl esm erce ri ze d si lk sy st . sys t.c o t ton 15 x 1 70 5---

Muslin . Batiste . Fine o a n d 00Iinens v thi n fabrics 80 t o 150 tw ist 10 70Shirtings Sheetings . A & BHeavy silks 80 t o 6 0 tw is t 14 90Heavy weight linens . CWoollen goods 6u t o 40 tw is t 16 100Heavy weight woollens . I 0Woven coating 40 to 30 tw ist 18 110Heavy fabrics in general 130 to 24 Etw is t 20 120

,

7

A-PDF Merger DEMO : Purchase from www.A-PDF.com to remove the watermark
http://www.a-pdf.com/http://www.a-pdf.com/http://www.a-pdf.com/


2/4

II

C HA PT ER I

- To run the machine by motor

A

~II'

~l e J&

Fig. 2

n) Pull Ollt button ((A (Fig. 2);b) Screw In button "B following the direction

o f the " rr ow;.) COil IH'("(, tho machine as shown in the illustrn-

tlou.Tho H('wlllf{ 11I1I('h111Cuns by pressing the rheostat" F II, ' 1 '1 1 ( \ Hwlt(:h , which ill found at the back 01'tho Hl'wIIlH Illll('hlnl', cont rols the built-in lightonly.8

~< I -

' "

. .

.j

",'.2 - To run the machine by hand.;,

Fig. 3.~

'i .~{ a) Disconnect the machine;b) Push in button ((A (Fig. 2) by rotating it as

far as itwill go;c) Unscrew button" B ;

d) Insert hand crank in "G (Fig. 3), to be, rotated in the direction of the arrow.

When you wish to run the sewing machine by

9


3/4

/d

hand and have the light on, connect plugs C ""and D" (Fig. 2), disregarding plug E n, ,3 - To remove the flat base ,In order to pass from a flat-bed machine to a free-arm one, unscrew button A" (Fig. 4), remove "the flat base and close the free arm by means of'carter B" (Fig. 5). :

Fig. 4 " '\I -~' I I

B

Fig. 5

10

CHAPTER II1 - Points to observea) Always keep a piece of cloth under the presser

foot when the sewing machine is not in use.This will prevent damage to the feed dog andthe presser foot. b) Do not push or pull the material to assist thefeeding action; the material must advance byitself. I2 - To oil the machinea) Oil the machine in all oiling points indicatedin Fig. 6 with a circle mark;b) It is advisable to oil the machine frequently;c) Use NECCHI oil, which is on sale at allNECCHI stores.

"

I

1 / )~)!J/1~)!J .>~~ ~ 8

B Fig. 611

~~]j .


4/4

I

3 - To insert the needle

a) Bring the needle bar to its highest positionby turning the balance wheel;

b) Loosen screw {(A" and insert the needle (Fig.7) into th ~ groove pushing it up as far as itwill go~~/

Make sure -that the flat side of the needle shank istoward the right.

Fig. 7

4 - To thread the machine

Thread the machine as illustrated in Fig. 6.

5 - To remove the bobbin case

a) Bring the needle bar to its highest position;b) Lift the extension leaf or remove the small

carter, according to the particular case;

12

. ~

c) Lift the latch of the bobbin case (Fig. 8) andremove bobbin case and bobbin.

The bobbin will be free only when the latch ofthe bobbin case is released.

. 1

' j

Fig. 8

6 - To wind the empty bobbin

1 Motor operation Treadle operationa) Unscrew button a) Unscrew button

{(B ", (Fig. 9); {(B ", Fig. 9, andpull out button{( A n ;b) Place thread as b) Place thread as

shown in the illus- shown in the illus-tration; tration;

c) Insert bobbin on bobbin winder spindle ((C ",which is in its central position.

13

Documents

Mirella Instructions Part 2