Mosman Council Public Domain Manual

November 2020

Mosman Council Public Domain Manual

Version: 4, Version Date: 30/10/2020Document Set ID: 5965487

pII November 2020


Prepared by:

and

115 Flinders Street Surry Hills NSW 2010 Ph: +61 2 9361 4549 [email protected]


00 Contents

1. Introduction ..................................................................................................... 3Background ................................................................................................. .................................3

Purpose ....................................................................................................... .................................3

Scope ............................................................................................................ .................................3

Objectives .................................................................................................... .................................3

2. Mosman’s Public Domain ............................................................................. 5History ........................................................................................................... .................................5

Urban ............................................................................................................. .................................7

Coastal .......................................................................................................... .................................9

Parks .............................................................................................................. .................................11

3. Public Domain Palette ................................................................................ 13Colour Palette .............................................................................................................................. 15

Precinct Patterns ........................................................................................................................ 16

Picnic Setting ...............................................................................................................................17

Seating .......................................................................................................................................... 18

Paving ............................................................................................................................................23

Kerbs and edging ....................................................................................................................... 26

Lighting .........................................................................................................................................29

Barbecue ..................................................................................................................................... 33

Rubbish Bins ............................................................................................................................... 34

Bollards ......................................................................................................................................... 36

Bike Hoops ................................................................................................................................... 40

Outdoor Shower .......................................................................................................................... 42

Banner Poles ............................................................................................................................... 43

Drinking fountains.......................................................................................................................47

Fence ............................................................................................................................................ 48

Bus shelter ................................................................................................................................... 50


p2 November 2020


BLANK PAGE



November 2020 p3

Background

Mosman occupies some 8.7 square kilometres located on Middle Head of Sydney Harbour to the northeast of Sydney CBD. Mosman’s unique visual character is shaped by the interplay of it’s harbour setting, topography, natural bushland, busy shopping strips and suburban neighbourhoods. The major thoroughfares of Military and Spit Roads both divide the area and connect residents of Mosman and those from further north to other parts of Sydney.

The Public Domain Manual is an initiative from Mosman Council to assist with the delivery of associated tasks that relate to the public domain. The new public domain items contained in the manual respond to the recent Signage Strategy and Style Guidelines developed for Mosman Council in 2017. The designs, colours and materials of each item within the Manual were chosen to complement the style and colour of the signs, as well as each other to provide a contemporary suite of public domain elements.

Purpose

The Public Domain Manual has been developed to ensure consistent design and maintenance of all parks and urban spaces within Mosman. The manual responds to existing conditions and previous work while addressing future intent and planning requirements.

The Manual outlines Mosman Council’s future approach to its public domain, sets out the quality and standard of what is expected in the public realm and contains a collection of new furniture and fixtures for the Local Government Area (LGA). A number of existing items are also included for reference and application where appropriate.

The manual provides details of suitable, like-for-like replacements for existing items that have reached their end of life and are not included in this manual. It is intended that items in the public domain are upgraded overtime with more suitable, quality products that contribute to an overall improvement to Mosman’s public domain.

01 Introduction

Scope

The Mosman Public Domain Manual sets guidelines, design coordination and material palettes for all public domain, streetscape and maintenance works in the Mosman LGA.

The manual has been written for a broad audience and is intended to be used by the residents, designers, developers, building owners and their agents (such as urban designers and landscape architects). In addition, the manual will be used by planners and other staff within Mosman Council to assess proposed development applications within the LGA.

The ‘Public Domain Manual’ applies to all work carried out in the public domain which are under or will revert to the ownership, care, control and management of Mosman Council.

The manual is not intended to initiate an extensive program of works but will be used to inform any works within the public domain that occur under Council’s normal operations. This manual works in conjunction with Council’s standard details to ensure new works implemented over time are cohesive and consistent.

All works must comply with Australian Standards and relevant approval authorities. Material choice should take into consideration Council’s actions to reduce emissions, as detailed in the Climate Change Action Plan.

Objectives

The key objectives for the Public Domain Manual are to:

− Establish a distinctive and consistent approach to the public domain; throughout Mosman’s parks, residential streets, urban centres, bushland and coastal areas;

− Deliver efficiencies to the design, documentation, procurement and construction of works in the public domain;

− Respond to significant, sensitive and/or heritage areas or items; − Provide transparency to the selection of materials; and − Create public spaces that are attractive, comfortable, accessible and easy to navigate.


p4 November 2020


BLANK PAGE



November 2020 p5

Mosman’s Public Domain02

History

Prior to colonial occupation of Sydney in 1788, the Mosman area was home to Aboriginal Australians for tens of thousands of years up to that time, living on a rich supply of food resources from the extensive shoreline and wooded headlands. HMS Sirius, flagship of the First Fleet, was careened in 1789 at what is now known as Mosman Bay. By 1815 most of the original inhabitants of this area had either died of disease or moved away.

The late 1820s to 1840s a flourishing whaling industry brought growth to the area. Land grants led to settlement and road construction over the second half of this century, with Mosman Public School, the Congregational Church, postal and telegraph services, the water supply and an electric tram service all established by 1893.

At the turn of the century, Mosman prospered as building activity intensified. Rows of shops and magnificent federation style homes were built by the increasing population, attracted to the natural charm and vistas of the unique bushland and water surrounds. Council policies zealously maintained parks and reserves with constant effort to enhance the beauty of the natural landscape.

In the late 1950s public concern focused on the number and type of flat developments occurring, i.e. multi-storey blocks on prominent sites. Population rose in the 1960s so new flats were built to cope with housing shortages throughout Sydney. At the end of the 1960s, Council introduced controls and restrictions and by 1973 high-rise development was banned.

Today’s challenge is to establish a strong connection to the past by which this vibrant local character can be protected into the future whilst at the same time establishing a framework for modern development within the Municipality.

Clifton Gardens swimming enclosure, circa 1909 Balmoral Beach northern end, circa 1950

Tram at Athol Wharf, circa 1957 Ferry at Mosman Bay, circa 1920


p6 November 2020


A

B

P

L

J

I

C

O

D

E

F

2

1

3

4

5

6

7

8

10

9

11

12

13

14

15

17

16

19

18

19

20

21

22

2524

26

27

28

G

H

N

K

ID NAME ATTRIBUTES*

Parks - Minor

1 Balmoral Beach Reserve (Edwards Beach) Be, Lo

2 Bay Street Park Bu, Ha, Lo, Pl

3 Carroll’s Lookout Bu, Lo, Po

4 Cartef park Po

5 Countess Park Pl, Po

6 Curraghbeena Park Lo, Pl

7 Drill Hall Common Bu, Sp

8 Ellery Park Ho, Lo, Po

9 Georges Heights Oval Bu, Lo, Sp

10 Hampshire Park Po

11 Harnett Park Bu, Ha, Lo

12 Hunter Park Pl

13 Joel’s Reserve Bu, Ha, Lo

14 Lawry Plunkett Reserve Bu

15 Leahy Park Be

16 Little Ashton Reserve Bu

17 Memory Park Pl, Po

18 Parriwi Lighthouse Lo

19 Parriwi Park Bu, Lo

20 Plunkett Park Bu, Pl

21 Quakers Hat Park Bu, Lo

22 Quakers Hat South Bu, Ha, Lo

23 Quakers Hat West Bu, Lo

24 Reginald Street Park Pl, Po

25 Reid Park Bu, Ha, Lo, Pl

26 Reservoir Park Po

27 Spit West Reserve Ha, Lo, Pl, Sp

28 Stan McCabe Park Bu, Ha, Lo

* KEY Be Beach-sideBu BushlandHa Harbour-sideLo LookoutPl PlaygroundPo PocketSp Sports-field

ID NAME

Urban - Major Centres

A Spit Junction

B Mosman Junction

C Mosman Square

Urban - Minor Centres

D Spofforth / Macpherson

E Lower Spofforth

F Avenue Road

ID NAME

Coastal - Major

G The Spit

H Balmoral Esplanade

I Clifton Gardens Reserve

Coastal - Minor

J Mosman Bay

K Rosherville Reserve

L Sirius Cove Reserve

ID NAME

Parks - Major

N Balmoral South

O Mosman Park

P Rawson Park

Figure 1. Map of urban, coastal and park precinct

URBAN

PRECINCT

COASTAL

PARKS

PARKS



November 2020 p7

Major Centres

Urban

Mosman has a number of minor centres, these small centres serve the local community. Minor centres provide valuable services, facilities and meeting areas that are easily accessed by residents. These centres should use materials that are consistent with other areas of Mosman but also afford an opportunity for unique and creative elements to accentuate the character and diversity of that particular centre.

Spit JunctionSpit Junction is a significant transport corridor where Military Road intersects with Spit Road, connecting the Northern Beaches with North Sydney and the city. The area is a plateau with ‘rib’ roads from the ridge top spine of Spit and Military Roads with north, south, east and west aspects. The subdivision pattern is linear following the ridge.

The existing character of the corridor reflects the roadway, transport and mixed residential and commercial functions. Known as Spit Junction Business Centre in Mosman Business Centres Development Control Plan (DCP) 2012, it is the primary business and retail centre, defined by Cowles Road to the west and Ourimbah Road to the north-east. Business development along the Military Road corridor to Cremorne is the predominant theme of this centre.

Mosman JunctionMosman Junction is the main retail area of Mosman and connects with Spit Junction and Mosman Square Urban Centres. It is Mosman’s premier retail strip and business hub formed along either side of Military Road which is a major traffic route to and from the southern and eastern areas of Mosman. The commercial development is broken up with some residential buildings and Mosman High School.

Mosman Junction Business Centre, as described in Mosman Business Centres DCP 2012, is contained entirely within the Military Road Heritage Conservation Area.

Mosman SquareMosman Square is the main civic area of Mosman and is the location of the Civic Centre, Seniors Centre, Art Gallery, Library, Youth Centre and village green. It links upper Military Road with Mosman Park and War Memorial through a series of pedestrian plazas and laneways. Mosman Square links Spit Junction and Mosman Junction Urban Centres. Parts of Mosman Square are contained within the Military Road and the Crescent Heritage Conservation Areas.


p8 November 2020


Minor Centres

Cremorne JunctionCremorne Junction Business Centre is located on the western boundary along the corners of Spofforth Street, Macpherson Street and Military Rd. It is a retail area on along the Military Road corridor.

The majority of shops are located to the west in Cremorne governed by North Sydney Council. This location represents a significant gateway into Mosman and provides an opportunity to improve the public domain.

Lower Spofforth Lower Spofforth is a small retail area stretching from Brierley Street to Calliope Street; it is made up predominately of cafés and food outlets with some residential houses and apartments.

It is named Spofforth Street Business Centre under the Mosman Business Centre DCP 2012. It is located on the boundary with North Sydney Council at the corner of Rangers Road, a key traffic route. The majority of shops are located on the eastern side within the Mosman Council area.

Avenue RoadThe Avenue Road centre is a small retail area made up of predominately cafés and food outlets. It located at a busy intersection at the Avenue Road and Canrobert St roundabout. It services the local residents and is close to Memory Park.

The centre falls within the Avenue Road and Mosman Bay Wharf Business Centre under the Mosman Business Centres DCP 2012.



November 2020 p9

Coastal Major

Coastal

Coastal areas provide a range of unique community uses and amenities which are connected to notable landscapes and open spaces. These places often include some level of commercial and retail activity which distinguish them from other coastal areas. The Major Coastal areas receive a high level of visitation from both the local community, out of area visitors and tourists so materials used have to be both of high quality and robust.

The SpitThe Spit is named after the sandbar that extends beyond Beauty Point. Spit Road and the Spit Bridge are located along this geographical feature and represent the only crossing over Middle Harbour in Mosman. The Spit is a focal point for water-based activities on Middle Harbour, where there are a series of marinas and associated businesses. Spit Road divides the locality into two areas; East and West. Spit East includes the majority of the commercial activity and the Spit to Manly section of the Bondi to Manly Walk. Spit West provides open space recreational opportunities and walking links to Beauty Point and Quakers Hat Bay.

Balmoral EsplanadeBalmoral Esplanade is a combination of retail areas, open space and residential development. The area is Mosman’s premier location with a series of significant sites and locations. The urban form is unique to the area with a series of bespoke items and distinctive materials and finishes.

Clifton Gardens ReserveClifton Gardens Reserve is a harbour foreshore park with a south-east facing beach, nestled between two steep ridges. The topography of the area provides the reserve with a sense of seclusion, which is enhanced by the surrounding native bushland.


p10 November 2020


Coastal Minor

Mosman BayMosman Bay, located on the southeast corner of Mosman, shares a boundary with North Sydney Council along Cremorne Point on the eastern side of the bay. The bay has strong history of maritime and fishing practices from both pre and post-colonial times. Today the bay is the major ferry link to Circular Quay from Mosman Wharf, South Mosman Wharf and Old Cremorne Wharf (located in North Sydney Council). There is a small amount of commercial activity, open space recreation and major walking links along the harbour.

Rosherville ReserveRosherville Reserve is a large northeast facing grass reserve surrounded by natural bushland and adjoining Chinaman’s Beach on Middle Harbour. The area is predominantly used for passive recreation, boating, swimming and walking. There is no commercial activity in the area, a small carpark and amenities block are located on the northern side of the reserve.

Sirius Cove ReserveSirius Cove Reserve, is located in the south of Mosman and is predominantly used for passive recreation and dog walking. The reserve is flanked by natural bushland and is a walking link between Mosman Bay, Curlew Camp, Taronga Zoo and Sydney Harbour National Park sections of the Bondi to Manly Walk.



November 2020 p11

Mosman ParkCentrally located, Mosman Park is the main civic park in the local government area, with a mix of land uses immediately surrounding the park including; Mosman Youth Centre, Mosman Library, Council administrative building, Mosman Public School, Mosman Bowling Club, Mosman Community Centre and Art Gallery and a mix of low and medium density housing.

Due to the location, the park is an important pedestrian thoroughfare with multiple paths throughout. The main features in the park include a war memorial, a popular children’s playground, Alan Border Oval and pavilion. The oval is frequently used by local schools, sporting clubs and informal groups for competition, training and play space. Main users of the oval are Mosman Cricket Club (summer) and Mosman Soccer Club (winter).

Parks Major

Parks

Mosman has over twenty five parks and open spaces, it also contains over 35 hectares of bushland. It is famous for its natural landscape and harbour views but it also has a variety of parks with diverse characters and purposes.

Balmoral SouthLocated at the southern end of Balmoral beach, Balmoral Oval is set amongst bushland slopes, it serves as an active recreation space supporting organised (cricket, soccer and school sport) and non organised activities (walking, cycling, jogging and outdoor exercise). A Scout Hall and Sailing Club are located on the eastern side of the park, which make use of the surrounding park and beach. Access is via the public carpark that serves both the oval, beach and associated clubs

Rawson ParkRawson Park is a heritage item with regional significance that is highly valued by the community. Located between Cross Street, Alexander Avenue and Middle Head Road, the park is on a ridgeline at one of the highest points in Mosman allowing panoramic views over Sydney and Middle Harbour. Rawson Park provides for a range of passive and active recreation uses including rugby, cricket, tennis, croquet, bushwalking and off-leash dog walking.

The park is made up of; Rawson Oval and pavilion at the upper, western end; Eastern Parklands located on the upper level with grass areas, the Scotland-Australia Cairn and the Anderson Memorial; Lower Area located on the northern side adjoining Croquet Lane includes tennis courts and croquet lawns with associated clubhouses; Bradley Bushland Reserve occupies the north-east area.


p12 November 2020


Below is a list of attributes that helps categorise how each park is used and maintained, parks may have one or multiple attributes.

Beach-sideLocated near beaches, with either a seawall or dune network providing an edge to the park and rocky outcrops at either end of the beach. Visitation at these parks is high all year, particularly in warmer months and therefore requires a high level of maintenance. Vegetation is fairly limited due to difficulties with front-line coastal environments.

BushlandBushland is a significant characteristic in Mosman and many parks feature some bushland reserve or are adjacent to bushland or National Parks. Maintaining native flora and fauna, walking tracks and controlling the spread of weeds is the main priority for bushland areas. Generally materials used in these areas are more subdued and reflect the natural materials found on site.

Harbour-sideHarbourside parks are located along the water’s edge bounded by a seawall but have limited or no water access. Other water related services or amenities, such as ferry wharves, boathouses, and marinas are located at or near these parks.

LookoutsBeing located on headland Mosman affords significant views across Sydney harbour in all directions. Many views can be enjoyed at lookouts strategically located on public land. The use of these areas varies; some lookouts will attract large crowds during certain events such as New Years Eve.

PlaygroundPlaygrounds are a key feature at many parks, each playground is unique but they all have similar requirements and maintenance needs.

PocketThese are small parks designed to service the needs of the local community. They are generally located in residential areas with well-defined edges and simple elements intended for short visits.

Sports-fieldsFlat open grasslands that are used for formal recreation. Specific sporting needs determine the size and layout of these spaces; surplus space provides opportunity for other informal uses and vegetation types. Sports-fields have a high level of maintenance to ensure good playing conditions for a given sport.

Other Parks and Open Spaces



November 2020 p13

This section outlines Council’s future approach to Mosman’s public domain. It sets out the quality and standard of what is expected in terms of furniture and fixtures for the different open space areas throughout the municipality. A number of existing items are also included for reference and application where appropriate.

The new public domain items respond to the Signage Strategy and Style Guidelines developed for Mosman Council in 2017. The designs, colours and materials of each item within the Manual were chosen to complement the style and colour of the signs, as well as each other to provide a contemporary suite public domain elements. These include three themed patterns for the signs used in their respective locations which are:

− Urban − Coastal − Parks

Suggestions of where each of the items are best located within these three categories are included in this section, in addition to appropriate colour palettes.

Public Domain Palette03


p14 November 2020


BLANK PAGE



November 2020 p15

2–Pac painted finish

SpecificationPaint - Dulux Ticking; orPaint - Dulux Domino

PrecinctUrbanCoastalParks

Proprietary product Ticking (GR20 / SG6G7)Domino (SG6G8)

SupplierDulux Australiahttp://www.dulux.com.au

NotesMatt preferred, satin may be acceptable but no gloss.

Anodised Finish

SpecificationSatin steel blue from Universal Anodises

Precinct UrbanCoastalParks

Proprietary product Satin Steel Blue

SupplierUniversal Anodiseshttp://www.universalanodisers.com.au

NotesRecommended anodising coat thickness:

− Interior: 10 microns − Exterior: Inland 20 microns / coastal 25 microns

Powder Coated Finish

SpecificationIronstone Matt 2607556M


Proprietary product Ironstone Matt 2607556M

SupplierDulux Australiahttp://www.dulux.com.au

NotesDuralloy 10 year rated finish for aluminium architectural BCA Class 1 Class 10. Equivalent in durability to what’s on the current shelters with the same ratings.

Colour Palette

Universal Anodisers Steel Blue – Interference Colour

Rockcote

Satin Steel Blue Steel Blue Windows Newcastle


p16 November 2020


Precinct Patterns

70.71

70.71

59.82

83.93

57.75

58.88

DRAFT B 05.05.2017

MOSMAN COUNCILSignage Strategy & Style Guidelines

Pg 14

3.1. COLOURS, PATTERNS AND MATERIALS

Sign Colour Primary Text Colour Secondary Text ColourBrand Colour

Theme Patterns

Urban Pattern Coastal Pattern Parks Pattern

Sign Frame - Anodised Aluminium

Text

• Easy to read in the outdoor environmentwhen in contrast with a darkbackground colour

Text

• Slightly darker than the Primary Textcolour in creating a visual hierarchybetween the two colours

• Easy to read in the outdoor environmentwhen in contrast with a darkbackground colour

• Used for distance walking times,pictograms text and legal notices.

Brand Box

• Used as background colour boxfor placement of 'Mosman' nameconsistently through all signage.

Sign Background

• Provides a neutral base for all othercolours to be placed upon

• Enables high contrast with white textwhich is the most legible approach

environment

• A recessive tone and will not dominatein the surrounding landscape

The following patterns are only used in the signage family Style 1. Pattern selectionwill be according to the signage location:

• Urban

• Coastal

• Parks

• Provides a dark neutral backgroundcolour to enable a high contrast withwhite text.

•panels and framework

• It is a recessive tone and will notdominate in the surrounding landscape

WHITE PMS COOL GREY 5 CDULUX TICKING GR20PMS EQUIVALENT: 432 C

GREYPMS 431 C

SATIN BLUE STEEL

Mosman Square

Bubbler

Mosman Square

Water Refill Station

Making one bottle of water uses 1 Litre of oil7 Litres of water

ygrene fo seluojageM 5.1

One less plastic bottle...

REDUCEREUSERECYCLE

This project is a NSW EPA Waste Less, Recycle Moreinitiative funded from the waste levy

Penalties apply in accordancewith Local Government Act 1993

mosman.nsw.gov.au Bubbler

Clifton Gardens

CliftonGardens


mosman.nsw.gov.au





REDUCEREUSERECYCLE


Bubbler

Mosman Park

Mosman Park





REDUCEREUSERECYCLE



No Dogs on Oval without consent

mosman.nsw.gov.au

DRAFT B 05.05.2017


Pg 33

4.4. DRINKING FOUNTAIN SUITE

Mosman Square

Bubbler

Mosman Square





REDUCEREUSERECYCLE




Clifton Gardens

CliftonGardens


mosman.nsw.gov.au





REDUCEREUSERECYCLE


Bubbler

Mosman Park

Mosman Park





REDUCEREUSERECYCLE




mosman.nsw.gov.au

DRAFT B 05.05.2017


Pg 33


Mosman Square

Bubbler

Mosman Square





REDUCEREUSERECYCLE




Clifton Gardens

CliftonGardens


mosman.nsw.gov.au





REDUCEREUSERECYCLE


Bubbler

Mosman Park

Mosman Park





REDUCEREUSERECYCLE




mosman.nsw.gov.au

DRAFT B 05.05.2017


Pg 33




November 2020 p17

Type 01 Picnic Setting

SpecificationThe Classic Plaza Table and Bench features slender battens made from eco-certified hardwood. Tailored end-access to accommodate a wheelchair.

Dimensions: 1750mm (L) x 720mm (H) x 2090mm (D)

Materials Eco-certified Jarrah Hardwood battensStainless Steel frame

Finishes Battens oiled - Jarrah colourFrame finished in Black colour

PrecinctParksCoastal

Proprietary product Classic Plaza Table and Bench

SupplierStreet Furniture Australia (http://www.streetfurniture.com)Oil - Nature’s Timber Oil (http://www.intergrain.com.au)

Installation requirementsSurface or Subsurface fixed

Seating

© Street Furniture Australia Pty Limited ABN 46 070 910 100

streetfurniture.com

Australia 1800 027 799United States +1 877 406 6434International +61 2 8774 8888

Email [email protected] 391 Park Road, Regents Park NSW 2143, Australia 80

COMPATIBLE SEATING:Refer to separate technical sheet. Classic Plaza DDA Seat (CMP5) Classic Plaza Bench (CMP4)

Need more information?For a brochure, image gallery, CAD downloads, installation and maintenance guides, go to:streetfurniture.com/au/product/classic-plaza-table/

Quick links:streetfurniture.com/au/colour-chart/streetfurniture.com/au/warranty/streetfurniture.com/au/parts-promise/

classic plaza tableClass: Tables | Family: Classic Plaza

CMP5 CMP5CMP6

CMP6 1750mm

CMP6 1750mm

SETTING OPTIONS

2010740

2010

635 58550

430

850

720

1750

1750

2090

50

CMP4 CMP4CMP6

2000740675 62550

470 72

0

CMP6 SHEET 2/2

August 2018


p18 November 2020


Type 01 Seat

SpecificationThe Classic Promenade Seat features slender battens in a wave profile with arm rests.



Finishes Battens oiled - Jarrah colourCustom Logo discs applied to each side of frameFrame finished in Night Sky Satin (Black)

Precinct Urban

Proprietary product Classic Promenade Seat


Installation requirementsSurface fixed

Seating


streetfurniture.com



classic promenade seatClass: Seats | Family: Classic Promenade

BULLNOSE TIE ROD: Aluminium Anodised Aluminium Powder Coated (see colour chart) Tailored

Some options incur additional fees and lead time.

Need more information?For a brochure, image gallery, CAD downloads, installation and maintenance guides, go to: streetfurniture.com/au/product/classic-promenade-seat/


SIDE VIEWSPLAY WIDE LEG

TOP VIEW1750mm

FRONT VIEW1750mm

FRONT VIEW2100mm

1810

2160

1750

2100

725

800

440

1760

5152110

CMR1 SHEET 2/2

October 2018


streetfurniture.com



Premium heritage-style seat features slender battens in a wave profile, made from eco-certified hardwood or aluminium, with a variety of leg designs.

MCODE:CMR1

DIMENSIONS (mm):1750L or 2100L x 725W x 800H

Select one box per category to specify your product.

CONFIGURATION: 1750mm 2100mm Tailored

FRAME: Cast Aluminium Powder Coated (see colour chart) Tailored

LEG AND MOUNTING: 01 Splay Wide Surface Fixed Subsurface Fixed Freestanding 02 Arch Surface Fixed Subsurface Fixed Freestanding 04 Pedestal Surface Fixed Subsurface Fixed 05 Post Surface Fixed with Cast Base Subsurface Fixed with Base Plate Core Drilled (300mm below ground) 07 Wall Wide (fixed to side of wall) 11 Plinth (fixed on top of wall)

BATTEN:Street Furniture Australia uses sustainable timber from certified managed forests. Timber requires oiling every three months.

Eco-certified Jarrah Hardwood, Oiled (PEFC) Eco-certified Cumaru Hardwood, Oiled (FSC) Aluminium Anodised Aluminium Powder Coated (see colour chart) Woodgrain* Bush Cherry Spotted Gum Grey Oak Tailored * Woodgrain comes with grey end caps unless otherwise specified.

classic promenade seatClass: Seats | Family: Classic Promenade

80180

520

515

725

440

800

300

80150

665

130

1760

SUBSURFACE FIXEDBASEPLATE

CORE DRILLED

WALL FIXED

PLINTH FIXED

FRONT VIEW

FRONT VIEW

SURFACE FIXED WITHCAST BASE

SURFACE FIXED

SURFACE FIXED

SURFACE FIXED

SUBSURFACE FIXED

SUBSURFACE FIXED

SUBSURFACE FIXED

FREESTANDING

FREESTANDING

01 S

PLAY

WID

E02

AR

CH

04 P

EDES

TAL

05 P

OST

07 W

ALL

11 P

LIN

TH

100

165

275

CMR1 SHEET 1/2

October 2018



November 2020 p19

Type 02 Seat

SpecificationThe Classic Plaza Seat features slender battens in a wave profile, available with arm rests.



Finishes Battens painted in Brunswick GreenFrame finished in Black colour

Precinct ParksCoastal

Proprietary product Classic Plaza Seat

SupplierStreet Furniture Australia (http://www.streetfurniture.com)


Seating

Feb 2015

This technical sheet is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100. You may download and use this technical sheet in unaltered form only for tendering our products to current or potential new clients. All rights are reserved. Any use of our technical sheet for purposes other than for the abovementioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited reserves the right to make modifications to product specifications without prior notice.

© Street Furniture Australia Pty Limited 2015. All rights reserved.

1800 027 799 streetfurniture.com

classic plaza seat CMP1

General Description

Classic, contoured seat supported by strong stainless steel frames.

Dimensions (mm)

705W x 800H x 1750L

Specifications

Tick one box per category to specify your product.

SEAT TYPE:CMP1

BATTENS:Section 40 x 20mm Eco-certified Hardwood Oiled* Aluminium Anodised*Street Furniture uses sustainably sourcedlocal timber from certified managed forests.

MOUNTING: Surface Subsurface

ARMS: None Angle Powder Coated (Pair)

POWDER COAT FINISH: Please refer to Colour Chart

Tailored options are available for all Street Furniture products. Additional fees and lead times may apply.

Related Products

Classic Plaza, Promenade and Galleria products

705

1750

800

445

1650

Arm (Optional)

80

PLAN

ELEVATION

Subsurface

Surface

CMP1 Classic Plaza Seat, 1750mm Length /SHS Frame Stainless 304 Base, Surface FixedMounting / Batten Eco-certified JarrahHardwood OiledPlaza Tailoring Jarrah Colour 2PAC batten Finish - Brunswick Green


p20 November 2020


Type 03 Seat

SpecificationThe Classic Galleria Bench features slender battens in a wave profile.

Dimensions: 1500-2000mm (L) x 420mm (H) x 625mm (D)


Finishes Battens oiled - Jarrah colourCustom Logo discs applied to each side of frameFrame finished in Night Sky Satin (Black)

Precinct UrbanParksCoastal

Proprietary product Classic Galleria Bench



Seating


streetfurniture.com



This classic range features slender battens in a comfortable curved profile, made from eco-certified hardwood or aluminium, with a variety of leg designs.

MCODE:CMG4

DIMENSIONS (mm): 1750L or 2100L x 615W x 435H


FRAME: Cast Aluminium Powder Coated (see colour chart) Tailored

LEG AND MOUNTING: 01 Splay Wide Surface Fixed Subsurface Fixed Freestanding 02 Arch Surface Fixed Subsurface Fixed Freestanding 04 Pedestal Surface Fixed Subsurface Fixed 05 Post Surface Fixed with Cast Base Subsurface Fixed with Base Plate Core Drilled (300mm below ground) 06 Tee Wide Surface Fixed Subsurface Fixed Freestanding 07 Wall Wide (fixed to side of wall) 11 Plinth (fixed on top of wall)

BATTEN:Street Furniture Australia uses sustainable timber from certified managed forests. Timber requires oiling every three months.

Eco-certified Jarrah Hardwood, Oiled (PEFC) Eco-certified Cumaru Hardwood, Oiled (FSC) Aluminium Anodised Aluminium Powder Coated (see colour chart) Woodgrain* Bush Cherry Spotted Gum Grey Oak Tailored * Woodgrain comes with grey end caps unless otherwise specified.

classic galleria benchClass: Benches | Family: Classic Galleria

SUBSURFACE FIXEDBASEPLATE

CORE DRILLED

WALL FIXED PLINTH FIXED

SURFACE FIXED WITHCAST BASE

SURFACE FIXED

SURFACE FIXED

SURFACE FIXED

SURFACE FIXED

SUBSURFACE FIXED

SUBSURFACE FIXED

SUBSURFACE FIXED

SUBSURFACE FIXED

FREESTANDING

FREESTANDING

FREESTANDING

01 S

PLAY

WID

E02

AR

CH

04 P

EDES

TAL

05 P

OST

06 T

EE W

IDE

07 W

ALL

11 P

LIN

TH 165

270

100

35

515

435

275

160

80

80

80

180

150

300

PowerMe Table(optional)

CMG4 SHEET 1/2

October 2018


streetfurniture.com



CONFIGURATION: 1750mm 2100mm 2 plus 2 with PowerMe™ Table* Tailored* Refer to PowerMe Table Technical Sheet.


Need more information?For a brochure, image gallery, CAD downloads, installation and maintenance guides, go to:streetfurniture.com/au/product/classic-galleria-bench/


classic galleria benchClass: Benches | Family: Classic Galleria

615

1750 (standard)

435

1550

435

1900

TOP VIEW1500mm

615

1200 300

TOP VIEW

FRONT VIEW1500mm

FRONT VIEW2100mm

435

1200

1250

2700

1250

FRONT VIEW2 PLUS 2 WITH POWERME TABLE

CMG4 SHEET 2/2

October 2018



November 2020 p21

Type 05 Seat

SpecificationTimber batten bench or seat designed to mount on walls. Suitable for use in areas where limited access behind seating such as garden beds and retaining walls. Steel supports can be fitted to form a backrest and arm rests.

Materials

Hardwood batten seat and back restAlternative material Composite woodStainless steel edging and support

Finishes Hardwood oiled

Precinct Coastal

Proprietary product Bondi

SupplierStraBe (http://strabe.com.au) or approved equivalent

Installation requirementsConsultation with supplier recommended

Seating


p22 November 2020


Type 06 Seat

SpecificationModular in nature, the collection offers an array of seat combinations including timber, powder coated steel, or lightbox elements that can be linked.

Length options: One Seater - 500mm Two Seater - 1000mm Three Seater - 1500mm Four Seater - 2000mm

Materials Glass-Fibre Reinforced Concrete (with oxide options)Hardwood Kwila Timber Slats/ Hardwood Tonka Timber SlatsGalvanised mild steel frame and arm rests

Finishes Finish Options for concrete: Primary (Clear Penetrative Sealer/ Wet Spray Painted FinishSecondary (Anti-Graffiti Clear/ Anti-Slip Texture)

PrecinctUrbanCoastal

Proprietary product Flinders Suite

SupplierStreet + Garden (http://streetandgarden.com)

Installation requirements4 x M12 Threaded rod Chemset into concrete. Sikaflex around perimeter of base

NotesRemove grime with damp cloth.Apply mild automotive polish to maintain original appearanceStandard 1 yr warranty on finishes and 5 year warranty on structure

Seating



November 2020 p23

Type 01 Paving

SpecificationExisting brick paving Bowral London Chestnut (infill paver) - 230mm (L) x 114mm (W) x 65mm (H)PGH Lasseter Gold (header paver) - 230mm (L) x 114mm (W) x 50mm (H)

Materials Clay

Finishes NA

PrecinctUrban - major and minor

Proprietary product PGH Lasseter Gold (header paver) orLittlehampton Hills Gold (header paver)Bowral London Chestnut (infill paver)

SupplierPGH (http://www.pghbricks.com.au)Littlehampton (http://www.littlehamptonbrick.com.au)Bowral bricks supplied Austral Bricks (https://australbricks.com.au)

Installation requirementsConcrete base as per detail

NotesP5 slip resistance Exposure grade

Paving

SCALE 1:20

0.50 0.8m

@A3

SCALE 1:20

0.50 0.8m

@A3

header paver

infill paver


p24 November 2020


Type 02 Paving

SpecificationExisting paving along Balmoral Beach

Materials 10mm basalt exposed aggregate mix with black oxide 10mm limestone exposed aggregate mix with grey cement

Finishes Agreed on site

Precinct Coastal - Balmoral Foreshore

Proprietary product Not available

SupplierNot available

Installation requirementsConcrete base

NotesN/A

Paving



November 2020 p25

Type 03 Paving

SpecificationConcrete footpath

Materials Concrete

Finishes Broom finish

PrecinctUrbanCoastalPark

Proprietary product N/A

SupplierN/A

Installation requirementsConcrete base as per detail

NotesBroom finish at 900 to the direction of travelWidth is 1400mm unless instructed otherwise

Paving

standard concrete paving

SCALE 1:10

0.2 0.4m0

@A3

SCALE 1:20

0.50 0.8m

@A3SCALE 1:10

0.2 0.4m0

@A3

SCALE 1:20

0.50 0.8m

@A3


p26 November 2020


Heritage Sandstone Kerb

SpecificationHeritage type kerb Maintain or reuse existing kerb stones in areas that currently have this kerb type

Materials Sandstone

Finishes N/A

Recommended locations Existing locations

SupplierN/A

Installation requirementsRefer to Council’s Engineering department

NotesN/A

Kerbs and edging

Indicative design



November 2020 p27

Heritage Park Edging

SpecificationHeritage type edgingPlain concrete with high durability

Suggested dimensions:Approx. 120mm above footpath x 150mm width (75mm radius)

Materials Concrete

Finishes Class 2

Recommended locations Coastal Parks

SupplierN/A

Installation requirementsConcrete base (110mm)

NotesSlip Resistance should be P4 (low risk) as a minimum

Kerbs and edging

Indicative design


p28 November 2020


Sandstone Edging

SpecificationSandstone edging constructed with ballast or random dimension stone Average dimension:300mm x 200/100mm x 100mm

Materials Sandstone

Finishes Rock face or Convict picks

PrecinctPark

Proprietary product Sandstone ballast or random dimension

SupplierANL (https://anlscape.com.au)

Installation requirementsMortar base

NotesGenerally installed between bushland or garden beds and lawns to control the spread of grass and assist with mowing and garden maintenance.

Kerbs and edging



November 2020 p29

Existing light pole currently used in Civic Lane

Type 01 Lighting

SpecificationPost Top Street Light LED Lamp

Materials Pole: SteelHousing: Marine-grade, die-cast aluminium

Finishes Pole: 2 Pack Epoxy Finish, Dulux Mid GreyHousing: RAL 9004 Fine Textured Black

Recommended locations Urban

Proprietary product Housing: 108-1317Lamp: As per requirements

SupplierHousing and Lamp: WE-EF (http://www.lightculture.com.au)

Installation requirementsNot available

NotesThis item is under review, Council have yet to determine the suitability and availability of this product, under these circumstances products used may vary.

Lighting

VFL

VFL

VFL

VFL

EXISTING

EXISTING

EXISTING

EE

EE

EE

EE

EE

EE

EE

EE

EE

EE

EE

SUPPLY FOR PUMSMO-14722

PIT

HOUSING FORCONTROL EQUIPMENT

50mm HD CONDUIT

6000 100mm DIAMETERSTRAIGHT ROUND

ACCESSDOOR

50mm DIAMETERSTRAIGHT ROUND

42 x 100mm SPIGOTTO SUIT WE-EF VFL530

250

1400

STANDARD BASEPLATE

120°

PAINTED FERREKO NO:3MICACEOUS OXIDEMID GREY

5000

BITUMOUS PAINT INTERNAL150mm ABOVE AND BELOW GROUND

"E"

"L"

"T"

"D"

PCD

FOUNDATION BOLT(INC: 2x NUTS & 2x WASHERS PER THREAD)

BASE PLATE

TOTALPOLE HEIGHT

FOUNDATION BOLTmm

"T"mm

"D"mm

"L"mm

"E"mm

BARS LIGATURES

16M16 x 550 x 233 P.C.D4.0 METRE 800 450500 500C/CN16

5.0 METRE M16 x 550 x 233 P.C.D 16 450500 1000

93/801-S1JULY 2011

VICPOLE DATA SHEET / INDICATIVE FOOTING DETAIL

*IMPORTANT NOTE: VICPOLE ACCEPTS NO RESPONSIBILITY FOR FOOTING DETAILS GIVEN. ALL FOOTING DETAILS AREINDICATIVE ONLY. FOOTING SIZES WILL VARY ACCORDING TO A NUMBER OF FACTORS INCLUDING SOIL CONDITION,WIND LOADING AND TERRAIN CATEGORIES. IN ALL INSTANCES IT IS THE RESPONSIBILITY OF THE CONTRACTOR TOOBTAIN ENGINEERS COMPUTATIONS TO DETERMINE THE FOOTING DETAIL REQUIRED FOR EACH SITE.*NOTE: Above footing detail based on terrain Cat 2, concrete strength 32 MPA, and an allowable lateral soil bearing pressure of 50kPaper metre depth.

PIPE, RHS, OCTAGONAL & TAPERED ROUND POLES

MINIMUM 6 x N16 BARS EQUALLY SPACED

R10 LIGATURES

N16 500C/C

100

100

100

100

GROUT UNDER THE BASEPLATE WITH ANADEQUATE NON-SHRINK CONSTRUCTIONGROUT (BY OTHERS)

Issue Amendment Date

DrawnProject No

ProjectLead Consultant

Drawing

Approv.Drawing No

Scale

Rev

Date

Client

© Copyright Lighting,Art & Science Pty Limited ABN 86 152 715 921All rights reserved. This drawing may not be reproduced or transmitted in any form ormeans in part or in whole without written permission of Lighting,Art & Science Pty Ltd

Lighting Consultants, Electrical EngineersLevel 1, 41 Hume St, Crows Nest NSW 2065p: +61 2 9436 0998 e: [email protected]

Lighting, Art & ScienceAS SHOWN

AS SHOWNT:\Projects\L148\L148L - Civic Lane Mosman\L148L-DG\L148L.dwg - EL-100 - 17/10/2017 - 4:07:44 PM

MOSMAN COUNCILJG

2016

NOV 2016

AEL-100

LIGHTING AND ELECTRICAL LAYOUT

L148L

CIVIC LANEMOSMAN

Notes:1. CONFIRM LUMINAIRE LENGTHS WITH SUPPLIER PRIOR TO ORDER AND ADVISE BUILDER OF

BLOCKOUT SIZES2. ALL RECESSED ENCLOSURES TO HAVE PAD LOCKING FACILITY WITH 3 POINT LOCKING PINS

02POLE & WE-EF VFL LUMINAIRE DETAILS

SCALE 1:20 @ A1

04SITE PLAN

SCALE 1:200 @ A1

A FOR CONSTRUCTION 17-10-17

03SCALE 1:20 @ A1

FOOTING DETAILS. CONSULT SUPPLIER FOR FULL DETAILS



p30 November 2020


LightingLighting

Indicative plan, front and side views of the different configurations

Existing light pole currently used in Mosman Indicative dimensions

Type 02 Lighting

SpecificationExisting light pole LED

Materials Steel pole

Finishes Anodised FinishSatin Steel Blue from Universal anodises


Proprietary product Not available

SupplierNot available

Installation requirementsNot available

NotesThis item is under review, Council have yet to determine the suitability and availability of this product, under these circumstances products used may vary.



November 2020 p31

Lighting

Possible configurations

Installation options

Type 03.1 Lighting

SpecificationPole mounted luminaire with bracket LEDUniform style elementsMinimalist luminaire designDisplaced de for street and footpath lighting

Materials Aluminium luminaire housingClear tempered safety glassGalvanised steel pole

Finishes Galvanised SteelChoice of any RAL


Proprietary product Linea single LEDLinea double LEDLinea displaced double LED

SupplierHess ( www.hess.com )Supplied in Australia by Form & Light ( formandlight.com.au )

Installation requirementsPosition the luminaire to avoid extended viewing into the luminaire at a distance of less than 0,4mConcrete footing

NotesHeight: 4500, 6000 or 8000mmOverhang: 1200 or 1500mm

This item is under review, Council have yet to determine the suitability and availability of this product, under these circumstances products used may vary.

Lighting

10

1.b 1.a

Empfohlene Montagefolge

Recommended Installation Procedure

Déroulement de montage recommandé

Secuencia de montaje recomendada

Sequenza di montaggio consigliata

2. 4. 3.

Demontage/Ausbau

Dismounting

Démontage

Desmantelamiento

Smontaggio

5.

1.c

8. 7. 6.

Wartung

Maintenance

Entretien

Mantenimiento

Manutenzione

Verstellung optional

Adjustment optional

Adjustement optionnel

Opción: ajustable

Regolazione opzionale

Einstellmöglichkeiten

“DIM Modul“

Settings “DIM Modul”

Possibilités de réglage du “Module DIM“

Posibilidades de ajuste „Módulo DIM“

Possibilità di regola-

zione del “Modulo

DIM“

10

1.b 1.a






2. 4. 3.

Demontage/Ausbau

Dismounting

Démontage

Desmantelamiento

Smontaggio

5.

1.c

8. 7. 6.

Wartung

Maintenance

Entretien

Mantenimiento

Manutenzione


Adjustment optional


Opción: ajustable



“DIM Modul“





zione del “Modulo

DIM“

11

1.Mast aufstellen/Flanschplatte/Erdstück

Putting Up the Pole/flange plate/embedded anchor

Ériger le mât/platines de fixation/pieu d’ancrage

Montaje del poste/placas base/conexión de puesta a tierra

Montaggio del palo/piastre di fissaggio/parte da interrare

1.a

•

A

>

> •

••

B

•

500

mm

1.b

•

A

>

> •

•

•

500

mm

Typ Q 300/25 Typ Q 400/30 Typ Q 500/35 Typ Q 250/12

1.C

19.20200.0

•

5

00

•

• •

12

• 1

00 •

150

•

• • 50

• 200 •

•

20

0

•

•

2

50

•

• 250 •

19.102.00.0 10.00200.4500

10.00202.4500

10.00200.8000

10.00202.8000

10.00222.8045

•

A

>

> •

Ø107

M12

1.C

19.10200.0 +

19.20200.0

•

5

00 m

m

L I N E A A B

mm mm

10.00200.4500 4500 800 Q 300/25

10.00200.6000 6000 1000 Q 400/30

10.00200.8000 8000 1500 Q 500/35

10.00202.4500 4500 800 Q 300/25

10.00202.6000 6000 1000 Q 400/30

10.00202.8000 8000 1500 Q 500/35

10.00222.8045 4500/4500 1500 Q 500/35

19.10200.0 950 - Q 250/12 3

00

20

0

200 42

22

10.00200.6000

10.00202.6000

40

0

30

0 300

30

0

47

27

30

0

50

0

40

0

400

47

27

200

250

20

0 14

33

11






1.a

•

A

>

> •

••

B

•

500

mm

1.b

•

A

>

> •

•

•

500

mm


1.C

19.20200.0

•

5

00

•

• •

12

• 1

00 •

150

•

• • 50

• 200 •

•

20

0

•

•

2

50

•

• 250 •

19.102.00.0 10.00200.4500

10.00202.4500

10.00200.8000

10.00202.8000

10.00222.8045

•

A

>

> •

Ø107

M12

1.C

19.10200.0 +

19.20200.0

•

5

00 m

m

L I N E A A B

mm mm

10.00200.4500 4500 800 Q 300/25

10.00200.6000 6000 1000 Q 400/30

10.00200.8000 8000 1500 Q 500/35

10.00202.4500 4500 800 Q 300/25

10.00202.6000 6000 1000 Q 400/30

10.00202.8000 8000 1500 Q 500/35

10.00222.8045 4500/4500 1500 Q 500/35

19.10200.0 950 - Q 250/12

30

0

20

0

200 42

22

10.00200.6000

10.00202.6000

40

0

30

0

300

30

0

47

27

30

0

50

0

40

0

400

47

27

200

250

20

0 14

33


p32 November 2020


Type 03.2 Lighting

SpecificationIlluminating bollard LEDMinimalist designOptimal illumination of foot paths and building entrancesStandard-conforming pathway lighting with minimal energyconsumptionHighly vandal resistant

Materials Galvanised steel poleGlass cover of polycarbonate

Finishes Galvanised SteelChoice of any RAL


Proprietary product Linea LED Bollard

SupplierHess (www.hess.com )Supplied in Australia by Form & Light (formandlight.com.au )

Installation requirementsConcrete footing

NotesTotal height above ground 1030mm.


10

1.b 1.a






2. 4. 3.

Demontage/Ausbau

Dismounting

Démontage

Desmantelamiento

Smontaggio

5.

1.c

8. 7. 6.

Wartung

Maintenance

Entretien

Mantenimiento

Manutenzione


Adjustment optional


Opción: ajustable



“DIM Modul“





zione del “Modulo

DIM“

11






1.a

•

A

>

> •

••

B

•

500

mm

1.b

•

A

>

> •

•

•

500

mm


1.C

19.20200.0

•

5

00

•

• •

12

• 1

00 •

150

•

• • 50

• 200 •

•

20

0

•

•

2

50

•

• 250 •

19.102.00.0 10.00200.4500

10.00202.4500

10.00200.8000

10.00202.8000

10.00222.8045

•

A

>

> •

Ø107

M12

1.C

19.10200.0 +

19.20200.0

•

5

00 m

m

L I N E A A B

mm mm

10.00200.4500 4500 800 Q 300/25

10.00200.6000 6000 1000 Q 400/30

10.00200.8000 8000 1500 Q 500/35

10.00202.4500 4500 800 Q 300/25

10.00202.6000 6000 1000 Q 400/30

10.00202.8000 8000 1500 Q 500/35

10.00222.8045 4500/4500 1500 Q 500/35

19.10200.0 950 - Q 250/12

30

0

20

0

200 42

22

10.00200.6000

10.00202.6000

40

0

30

0

300

30

0

47

27

30

0

50

0

40

0

400

47

27

200

250

20

0 14

33

Lighting



November 2020 p33

Type 01 Barbecue

SpecificationFully accessible double electric barbecue suitable for parks and recreational areas. Timed cooking hot plate made from 316 stainless steel with two-year warranty and lifetime warranty for structural failures.

Dimensions: 950mm (W) x 1900mm (L) x 850mm (H)

Materials Stainless steel and aluminium

Finishes Powder coated (aluminium)

PrecinctCoastal Parks

Proprietary product Frontier Double BBQ

SupplierGrillex (https://grillex.com.au)Supplied by Unisite Group (http://www.unisitegroup.com.au)

Installation requirementsSurface fixed

NotesFully tested and certified to Australian standards.

Barbecue

FRONT VIEW SIDE VIEW

TOP VIEW

BBQ Dimensions

BBQ Overall size 1900mm (w) x 850mm (h) x 950mm (d)

BBQ Slab Dimensions

Allow 1000mm extra around the edges of the BBQ. - eg. BBQ 1900 x 950m / Slab 3900 x 2950mm

Access Doors

Access doors come standard on the front of the BBQ. Optional rear doors are available.


p34 November 2020


Type 01 Rubbish Bin

SpecificationDeveloped to be fire retardant and graffiti resistant suitable for the heavy demands of public spaces. The patented design of Gossi Park enclosures secures a standard wast bin within a lockable cabinet while restricting the airflow reducing the intensity of a fire.

Dimensions: 930mm (W) x 1360mm (H) x 710mm (D)

Materials Extruded aluminium

Finishes Anodised finish - Olive Mist to cabinet and hood

PrecinctUrbanCoastal Parks

Proprietary product Bayside Bin Enclosure 240L capacity

SupplierGossi Park and Street Furniture (http://gossi.com.au)

Installation requirementsSurface fixed - Bolt Down with silicone sealant

NotesThe door secures with a slam lock, accessible on the left side of the unit

Rubbish Bin



November 2020 p35

Rubbish Bin

Type 02 Rubbish Bin

SpecificationA robust, vandal resistant unit suitable for 120 litre capacity bin.

Dimensions: 645mm (W) x 1160mm (H) x 645mm (D)

Materials Hardwood slats, aluminium frame and hood

Finishes

Slats, oiled Battens - Jarrah colourHood, powder coated in Brunswick Green

PrecinctUrban - Mosman Square

Proprietary product Town & Park MB.T3 Bin

SupplierTown & Park (http://townandpark.com.au)Oil - Nature’s Timber Oil (http://www.intergrain.com.au)

Installation requirementsSurface fixed - Bolt Down

NotesN/A

P: 1300 782 101W: townandpark.com.auE: [email protected]

Copyright Stoddart Pty Ltd. All rights reserved.

Construction:• Marine grade aluminium cast • 316 stainless steel fasteners• Hardwood timber slats or extruded

aluminium• Timber coated with high quality timber oil

or 25um clear anodised aluminium

Finishes:• Powder Coated

Example Specification Text:

Model Code: SPTP.MB.T3.H.240

Town and Park Mobile Bin Enclosure CBD MB1 with FSC 100% hardwood slats coated with a high quality outdoor decking oil. The hood is manufactured from marine grade aluminium casting. This enclosure houses 120 litre bins.

Models:Code: SPTP.MB.vv.xx.yyy.zz

SPTP = Stoddart Product - Town and ParkMB = Mobile Bin Enclosure - MB1

vv T2 = Select Grade Hardwood Slats T3 = FSC 100 % Hardwood Slats A = Anodised Aluminium Slats

xx CL = Cover Lid H = Hood F = Flat Hood

yyy 120 = 120 Litre bin

zz PC = Powder Coated

Options: ASH = Ashtray e.g.: for specification and ordering quote Town and Park model: SPTP.MB.T3.H.240

Install Details:All measurements in millimetres

MOBILEBIN MB


p36 November 2020


Bollards

Type 01 Bollard

SpecificationTraditional style bollard in cast aluminiumDimensions: 940mm (H) x 250mm (W)

Materials Cast Aluminium Powder CoatedConcrete base

Finishes Powder coat - Heritage Green

Precinct UrbanCoastal

Proprietary product B4

SupplierStreet Furniture Australia (http://streetfurniture.com/au/)

Installation requirementsSurface mounted, Subsurface mounted, Removable Surface fixed or Removable In-ground

NotesChain link option

Feb 2015

This technical sheet is copyright and owned by Street Furniture Australia Pty Limited ACN 070 910 100. You may download and use this [technical sheet / drawing] in unaltered form only for tendering our products to current or potential new clients. All rights are reserved. Any use of our [technical sheet / drawing] for pur-poses other than for the abovementioned purpose, is strictly prohibited without the prior written permission of Street Furniture Australia Pty Limited, Level 1, 52-58 William Street, East Sydney NSW 2011. Street Furniture Australia Pty Limited reserves the right to make modifications to product specifications without prior notice.

© Street Furniture Pty Limited 2015. All rights reserved.

1800 027 799 streetfurniture.com

traditional bollardB4

General Description

Our bestselling bollard offers simplicity and timeless appeal.

Dimensions (mm)

250W x 250D x 940H

Specifications

BOLLARD TYPE:B1

BODY:Cast Aluminium Powder Coated**Refer to Colour Chart

MOUNTING: Surface Subsurface

Customisations are available for all Street Furniture products. Additional fees and lead times may apply.

250

210

250

210

185

215

185

215

Ø15

Ø15

Ø250

940

PLAN

PLAN

B4 Traditional

Subsurface Base Plate

x4 holes

140

315

315

230

230

Ø15x4 holes

PLANBase Pavement Socket

260

80

395

Subsurface

Surface

Mounting Options

RemovableIn-ground

Removable Surface fixed



November 2020 p37

Bollards

Type 02 Bollard

SpecificationStainless steel angled bollardDimensions: 1050mm x 230mm45 degree angle

Materials 304 Grade stainless steel

Finishes Stainless steel


Proprietary product Designer Edge Bollard

SupplierAustralian Bollardshttp://www.australianbollards.com.au

Installation requirementsSub-Surface mounted, Internal mounting frame bolted with 1 x M16.

NotesNA


p38 November 2020


Bollards

Type 03 Bollard

SpecificationA square timber bollard Dimensions: 125-150mm(W) x 125-150mm (D) x 1500mm (H)

Materials Timber

Finishes Paint - Dulux Ticking

Precinct UrbanParks


SupplierN/A

Installation requirementsInground

NotesCustomisation available including vehicle reflector



November 2020 p39

Bollards

Type 04 Bollard

SpecificationSandstone heritage bollard Dimensions: 125-150mm(W) x 125-150mm (D) x 1500mm (H)

Materials Sandstone

Finishes N/A

Precinct Myahgah Road (Mosman Square)


SupplierN/A

Installation requirementsInground

NotesN/A


p40 November 2020


Bike Hoops

Type 01 Bike Hoop

SpecificationFull steel bicycle standDimensions 850mm (H) x 845mm (W) x 70mm Ø

Materials Stainless steel 304, 316 or mild steel

Finishes Stainless Brushed or Mild Zinc Phosphate, Hot Dipped Galvanised, Powder Coat


Proprietary product Semi Hoop

SupplierMultiple suppliers including:Street Furniture Australia (http://streetfurniture.com/au/)

Installation requirementsSurface FixedSubsurface FixedCore Drilled

NotesNA

221


streetfurniture.com


Email [email protected] 391 Park Road, Regents Park NSW 2143, Australia

The wide U-shaped bicycle stand wholly supports the bicycle at two points. Complies with AS2890.3 Class 3.

MCODE:BST03

DIMENSIONS (mm):845L x 120W x 850H


PIPE: Stainless 304 No.4 Finish (brushed) Stainless 316 No.4 Finish (brushed) Mild Steel Zinc Phosphate Mild Steel Hot Dipped Galvanised Mild Steel Zinc Phosphate Powder Coated (see colour chart) Tailored

MOUNTING: Surface Fixed Subsurface Fixed Core Drilled (300mm below ground) Tailored


Need more information?For a brochure, image gallery, CAD downloads, installation and maintenance guides, go to: streetfurniture.com/au/product/semi-hoop/


semi hoopClass: Bike Parking | Family: Hoop

800

845

850

Ø70

TOP VIEW

MOUNTING OPTIONS

FRONT VIEW WITH BIKE

CORE DRILLED SUBSURFACE FIXED SURFACE FIXED

BASE PLATE DETAIL

4x Ø14 holes Ø87

Ø120

300

80

BST03 SHEET 1/1

August 2018



November 2020 p41

Bike Hoops

Type 02 Bike Hoop

SpecificationCorkscrew Bike RackDimensions 805mm (H) x 900mm (W) x 900 - 4200 (L)

Materials 316 Stainless steel

Finishes Satin Polished


Proprietary product Spiral Bike Rack

SupplierCommercial System Australia (www.commercialsystems.com.au)or approved equivalent

Installation requirementsSubsurface FixedSurface Fixed

NotesNA


p42 November 2020


Type 01 Shower

SpecificationAs per elevations

Materials Stainless steel, timber, chrome

Finishes Satin

Precinct Coastal

Proprietary product Bespoke wall mount shower

SupplierCustom built

Installation requirementsAs per elevations

NotesDesigned by Mode (Surry Hills)

Outdoor Shower

CAROMA TRACK FIXED SHOWER OUTLET;CODE 90211C3A

5mm STAINLESS STEEL SHEETING FIXEDTO WALL

75x25mm TALLOWWOOD BRITTON TIMBERNATURAL FINISH; FIXED TO STAINLESS STEELSHEETING W/ STANDOFF BRACKET

STANDOFF BRACKET MODEL 10, 38mm SATINFINISH AISI 316 MIAMI STAINLESS RANGE; CODEP3010-38SF; W/ DUAL THREADED COACH SCREWM8 X 60 AISI 304; CODE S3183-081638

FOOT WASH RBA CONICAL SHOWERHEAD, 7LMPWALL FIXED; CODE RBA8519-107

DZR BRASS, CHROME PLATED SELF CLOSING SHOWERTAP PUSH ACTIVATED TIME, FLOW 20-30 SECONDS;CODE RBA1055-530

1750

2030

750

550

10mm SHORT LINK STAINLESS STEEL CHAIN TOCONNECT SHOWER CASING, BASE ANDCONCRETE HARDSTAND

60

AR-5511

2DASHED LINE INDICATING OUTLINE OFCONCRETE HARDSTAND

AR-55113

NOM.

900

NOM

.

900

50

240

75x25mm TALLOWWOOD BRITTON TIMBER WITH2 COATS INTERGRAIN ULTRADECK WITHULTRAGRIP; FIXED TO STEEL RHS

STEEL RHS POWDERCOATED IN XTREMECHARCOAL SATIN FLUROSET

50

5050

10

C.O.

S

188019

60

EQEQ

759075

890

STANDOFF BRACKET MODEL 10, 38mm SATIN FINISH AISI 316MIAMI STAINLESS RANGE; CODE P3010-38SF; W/ DUALTHREADED COACH SCREW M8 X 60 AISI 304; CODES3183-081638

75x25mm TALLOWWOOD BRITTON TIMBER NATURAL FINISH;FIXED TO STAINLESS STEEL SHEETING W/ STANDOFF BRACKET

DZR BRASS, CHROME PLATED SELF CLOSING SHOWER TAPPUSH ACTIVATED TIME, FLOW 20-30 SECONDS; CODERBA1055-530

5mm STAINLESS STEEL SHEETING

150mm NOM. CONCRETE HARDSTAND TO BE BRACED TO WALL

100

230

280

280

300

280

EXISTING PIER & WALL

10mm SHORT LINK STAINLESS STEEL CHAIN TO CONNECTSHOWER CASING, BASE AND CONCRETE HARDSTAND

SYDNEY

Suite 1, 35 Buckingham StSurry Hills NSW 2010T +61 2 8396 [email protected]

SYDNEY


SYDNEY


SYDNEY


SYDNEY


SYDNEY


SYDNEY


SYDNEY


SYDNEY


• These designs and plans are the copyright of MODE DESIGNCorp. Pty Ltd and cannot be reproduced without writtenpermission.

• Verify all dimensions on site prior to commencement of work.• DO NOT scale off these drawings.• Report any discrepancies to the architect before carrying out any

work.

ISSUE: SCALE @ A3:

PROJECT No DRAWING No REV

DRAWING TITLE

CHECKED:

CLIENT

PROJECT

DRAWN:

STAGE

ABN: 65 112 807 931

NORTHISSUE

1

1 : 20

14/12

/2017

9:18

:20 A

M

BESPOKE WALL MOUNTSHOWER

11/30/17

MOSMAN COUNCIL

BALMORAL PROMENADEBALMORAL, MOSMAN, NSW 2088

AR-551116602SYD CC

AMENDMENTS

REV DESCRIPTION AUTH CHK DATE1 ISSUED FOR COMMENTS BZ SH 14/12/17

ELEVATION 2

PLAN

ELEVATION 1

3D WALL MOUNT SHOWER



November 2020 p43

Type 01 Pole

SpecificationSimple pole attachment for existing light poles.

Materials

Aluminium and stainless steel

Finishes N/A



SupplierUniversal Signage Solutions (http://universalsignage.com.au)

Installation requirementsRequires high access equipment

NotesN/A

Banner Poles


p44 November 2020


Type 02 Pole

SpecificationThe HUB.Pole is a modular system that starts as an elegant and inexpensive column which, via the addition of the unique HUB Universal Mounting System (UMS), becomes a fully capable, MFP System, that can accommodate all current and future urban pole mounted accessories.

The HUB.Pole accommodates Lighting, Traffic signals, Signage, Banner, CCTV, Solar and Telecommunication accessories and can be custom modified to suite the needs of your project.

It is fully flexible in terms of:

− Pole Height − Pole Diameter − Accessories accommodated immediately − Accessories accommodated in the future − Ability to customise the aesthetics to suit the character of each city

Materials Extruded Aluminium/ Rimex rigidised 316 stainless steel

Finishes Clear anodised

Recommended locations UrbanCoastal

Proprietary product HUB.Pole

SupplierHUBhttp://hub-group.com

Installation requirementsM24 Stud Bent GAL bolts in concrete footing

Notes

System: uses a Universal Mounting System (UMS) which is an easy to install mounting hub giving the system its multi functionality. This represents a distinct advancement away from the traditional track based system and the inherent flaws associated with this design approach. The HUB UMS has allowed HUB to provide a more cost effective, more functional, more flexible and more universal solution to those seeking the distinct advantage offered by this type of public domain infrastructure. The HUB UMS is only applied when needed and can be added or removed at any time.


Banner Poles

Registered Design © Copyright HUB Innovations Pty Ltd | www.hub-group.com

TheHUB.PoleisabeautifullysimpleandinternationallyrecognisedMultiFunctionalPoleSystemthatoffersgreaterflexibilityandgreatervaluetothisproductcategory.TheHUB.Poleisamodularsystemthatstartsasanelegantandinexpensivecolumnwhich,viatheadditionoftheuniqueHUBUniversalMountingSystem(UMS),becomesafullycapable,MFPSystem,thatcanaccommodateallcurrentandfutureurbanpolemountedaccessories.

TheHUB.PoleaccommodatesLighting,Trafficsignals,Signage,Banner,CCTV,SolarandTelecommunicationaccessoriesandcanbecustommodifiedtosuitetheneedsofyourproject.

TheHUB.PoleMultiFunctionalPoleSystemcombinesamultitudeofstreetpolefunctionsontoasingle,beautifullydesignedstructuralurbanelement.TheHUB.Polesystemisafullymodularsystemthatcanbeadaptedtotheneedsofanymoderncity,bothnowandinthefuture.Itisfullyflexibleintermsof:

·PoleHeight·PoleDiameter·Accessoriesaccommodatedimmediately·Accessoriesaccommodatedinthefuture·Abilitytocustomisetheaestheticstosuitthecharacterofeachcity

SYSTEMTheheartoftheHUB.PolesystemistheUMS,orUniversalMountingSystem.TheHUBUMSisapatentedandeasytoinstallmountinghubwhichgivesthesystemitsmultifunctionality.Thisrepresentsadistinctadvancementawayfromthetraditionaltrackbasedsystemandtheinherentflawsassociatedwiththisdesignapproach.

TheHUBUMShasallowedHUBtoprovideamorecosteffective,morefunctional,moreflexibleandmoreuniversalsolutiontothoseseekingthedistinctadvantageofferedbythistypeofpublicdomaininfrastructure.

TheHUBUMSisonlyappliedwhenneededandcanbeaddedorremovedatanytime.TheHUBUMSaccommodatesLighting,Traffic,SignageandTelecommunicationaccessories.TheHUBUMSisastructurallycapableandeasytoinstallelementthatprovidesmaximumflexibilityintermsofthebroadrangeofaccessoriesavailable,theirmountingheightandtheirorientation.

AccESSoRiESTheHUB.Polesystemisdesignedtoaccommodatethecompleterangeofpolemountedaccessoriestypicallyfoundinthemodernpublicdomain.Inaddition,theHUB.Polecanbemodifiedtoaccommodateanevengreaterrangeofaccessoriesthatmayberequirednow,orinthefuture.Pleasecontactustodiscussyourspecificrequirementsandwewouldbehappytoworkwithyoutofindthesolutionyouareafter.

vARiATionSTheHUB.Polecanbecustomisedtoensureitbecomesauniqueexpressionofyourproject.TheHUB.PolecanprovideastrongopportunityforanyAuthorityorCouncilseekingtocreateauniquesenseofplaceinanypublicdevelopmentorCity.Keyelementsofthesystemthatallowanopportunitytowardsthisendincludefeaturelighting,basecladding,finishesandlightoutreaches.

30

150

300

219 168 114

Multi-Function PolEsHuB.Pole


TheHUB.PoleisabeautifullysimpleandinternationallyrecognisedMultiFunctionalPoleSystemthatoffersgreaterflexibilityandgreatervaluetothisproductcategory.TheHUB.Poleisamodularsystemthatstartsasanelegantandinexpensivecolumnwhich,viatheadditionoftheuniqueHUBUniversalMountingSystem(UMS),becomesafullycapable,MFPSystem,thatcanaccommodateallcurrentandfutureurbanpolemountedaccessories.

TheHUB.PoleaccommodatesLighting,Trafficsignals,Signage,Banner,CCTV,SolarandTelecommunicationaccessoriesandcanbecustommodifiedtosuitetheneedsofyourproject.

TheHUB.PoleMultiFunctionalPoleSystemcombinesamultitudeofstreetpolefunctionsontoasingle,beautifullydesignedstructuralurbanelement.TheHUB.Polesystemisafullymodularsystemthatcanbeadaptedtotheneedsofanymoderncity,bothnowandinthefuture.Itisfullyflexibleintermsof:

·PoleHeight·PoleDiameter·Accessoriesaccommodatedimmediately·Accessoriesaccommodatedinthefuture·Abilitytocustomisetheaestheticstosuitthecharacterofeachcity

SYSTEMTheheartoftheHUB.PolesystemistheUMS,orUniversalMountingSystem.TheHUBUMSisapatentedandeasytoinstallmountinghubwhichgivesthesystemitsmultifunctionality.Thisrepresentsadistinctadvancementawayfromthetraditionaltrackbasedsystemandtheinherentflawsassociatedwiththisdesignapproach.

TheHUBUMShasallowedHUBtoprovideamorecosteffective,morefunctional,moreflexibleandmoreuniversalsolutiontothoseseekingthedistinctadvantageofferedbythistypeofpublicdomaininfrastructure.

TheHUBUMSisonlyappliedwhenneededandcanbeaddedorremovedatanytime.TheHUBUMSaccommodatesLighting,Traffic,SignageandTelecommunicationaccessories.TheHUBUMSisastructurallycapableandeasytoinstallelementthatprovidesmaximumflexibilityintermsofthebroadrangeofaccessoriesavailable,theirmountingheightandtheirorientation.

AccESSoRiESTheHUB.Polesystemisdesignedtoaccommodatethecompleterangeofpolemountedaccessoriestypicallyfoundinthemodernpublicdomain.Inaddition,theHUB.Polecanbemodifiedtoaccommodateanevengreaterrangeofaccessoriesthatmayberequirednow,orinthefuture.Pleasecontactustodiscussyourspecificrequirementsandwewouldbehappytoworkwithyoutofindthesolutionyouareafter.

vARiATionSTheHUB.Polecanbecustomisedtoensureitbecomesauniqueexpressionofyourproject.TheHUB.PolecanprovideastrongopportunityforanyAuthorityorCouncilseekingtocreateauniquesenseofplaceinanypublicdevelopmentorCity.Keyelementsofthesystemthatallowanopportunitytowardsthisendincludefeaturelighting,basecladding,finishesandlightoutreaches.

30

150

300

219 168 114

Multi-Function PolEsHuB.Pole



November 2020 p45

9100

UP TO 3000

2200

FINISHED GROUND LEVEL

SECTION OF 214 MASTSCALE 10:1

ALUMINIUM NATURAL SATIN ANODIZE 20-23 Um

9600

DIE CAST TRANSITION ALUMINIUM NATURAL SATIN ANODIZE

LUMINAIREby others

600HATCH

200HATCH

110

450

160

250

390

FGL

400 PCD

REMOVABLECLADDING

REMOVABLE CLADDING

TWIN LIGHT ARM OPTION

2366447-250 FOOT PROFILE

2366616B 234 GENERIC BURIED BASE

2366456 234 CLADDING

2366615B 214 MAST SINGLE

2366941 214 MAST TWIN

2366235 DIA 80 LIGHT ARM

2366246 DIA 73 SPIGOT

2366578 LIGHT SPIGOT 60

2366641A 214 CAP

SECTION OF 234 BASE ASSEMBLY

SCALE 10:1ALUMINIUM NATURAL SATIN ANODIZE 20-23 Um

BANNERby others

BANNERby others 4500 max

1500 max

NOTEPATENT PENDINGALL INFORMATION CONTAINED IN THIS DRAWING IS CONFIDENTIAL AND MUST NOT BE DISCLOSED TO OR COPIED BY ANY THIRD PARTY WITHOUT WRITTEN CONSENT FROM GOODCART PTY LTD.

COPYRIGHT GOODCART PTY LTD 2015 AUSTRALIAN DESIGN REGISTEREDPATENTS APPLIED FOR

300 SERIES 9100 HEIGHT

MULTIPOLE 2366950

Multipole Accessories bracket

1000

400 PCD

90°

ROAD ALIGNMENT

M24FOUNDATION BOLT

STEELTEMPLATE

place nuts and washersabove and below template

M24 NUT

75 mm WASHER


CONCRETE FOUNDATION

450

160

100

exposed thread,keep free fromconcrete !

COAT BURIED ALUMINIUM COMPONENTS WITH DUREBILD PRIMER 150 MICRONS

NoteAll buried components must be coated with DUREBILD STE paint 150 microns.IP 65 rated electrical enclosures to be used for electrical connections.Stainless steel fixings to be isolated from Aluminium components with Barium Chromate paste.

NOTEAll poles manufactured in accordance with relevant standards

Pole footings to be engineered by others to suit local environmental and ground conditions.

BASE DETAIL

Patented Multipole Footing System Foot Extrusions, 4 offAluminum 6005A T5Anodized 20 Microns12 x M20 Bolts Galvanized 8.8 Grade Steel

Foundation boltsM24 @ 400 PCD

NOTEAll extruded Aluminium parts to be clear satin anodised 20-23 micron

T +61 2 9997 1278F +61 2 9997 3533E [email protected]

2/81 Basset Street Mona ValeNSW 2103AUSTRALIA

Type 03 Pole

SpecificationAluminium banner poles designed to accommodate a range of banner systems and light fittings. The design enables banners to be hung as single banners or twin banners with poles certified to a height of 12m.

Modular system can carry additional applications such as light fittings.

An option is available that enables banner arms to be raised and lowered like a flag on a flag pole, thus removing the need for a cherry picker or access platform to change banners.

Materials Extruded Aluminium

Finishes Clear satin anodised 20-23 micron


Proprietary product Multitpole 300 Series

SupplierGoldspar Grouphttp://www.lightpole.com/

Installation requirementsConcrete foundation engineered to suit local environmental conditions

NotesOptional Accessories: Banner raising system, PA outlets, Single or twin banner arms, Street signage, Rag bolts kits.


Banner Poles

9100

UP TO 3000

2200




9600


LUMINAIREby others

600HATCH

200HATCH

110

450

160

250

390

FGL

400 PCD

REMOVABLECLADDING

REMOVABLE CLADDING






2366941 214 MAST TWIN




2366641A 214 CAP



BANNERby others


1500 max




MULTIPOLE 2366950


1000

400 PCD

90°

ROAD ALIGNMENT

M24FOUNDATION BOLT

STEELTEMPLATE


M24 NUT

75 mm WASHER


CONCRETE FOUNDATION

450

160

100






BASE DETAIL






9100

UP TO 3000

2200




9600


LUMINAIREby others

600HATCH

200HATCH

110

450

160

250

390

FGL

400 PCD

REMOVABLECLADDING

REMOVABLE CLADDING






2366941 214 MAST TWIN




2366641A 214 CAP



BANNERby others


1500 max




MULTIPOLE 2366950


1000

400 PCD

90°

ROAD ALIGNMENT

M24FOUNDATION BOLT

STEELTEMPLATE


M24 NUT

75 mm WASHER


CONCRETE FOUNDATION

450

160

100






BASE DETAIL






9100

UP TO 3000

2200




9600


LUMINAIREby others

600HATCH

200HATCH

110

450

160

250

390

FGL

400 PCD

REMOVABLECLADDING

REMOVABLE CLADDING






2366941 214 MAST TWIN




2366641A 214 CAP



BANNERby others


1500 max




MULTIPOLE 2366950


1000

400 PCD

90°

ROAD ALIGNMENT

M24FOUNDATION BOLT

STEELTEMPLATE


M24 NUT

75 mm WASHER


CONCRETE FOUNDATION

450

160

100






BASE DETAIL







p46 November 2020


Type 04 Pole

SpecificationThe SmartPoleTM reduces streetscape clutter by accommodating a range of pole mounted accessories onto a single pole system. The SmartPoleTM achieves this multi-functionality through a patented track detail integrally formed into the pole. This track provides the fixing detail into which a full range of accessories can be connected. This range of accessories includes, but is not limited to, street lighting, banners, pedestrian lighting, CCTV, telecommunications technology, feature lighting, traffic signals, VMS, signage, pedestrian signals.

The HUB.Pole system is a fully modular system that is fully flexible in terms of:

− Pole Height − Pole Diameter − Accessories accommodated immediately − Accessories accommodated in the future − Ability to customise the aesthetics to suit the character of each city

Materials Extruded Aluminium/ Rimex rigidised 316 stainless steel

Finishes Clear anodised


Proprietary product Smartpole

SupplierHUB

Installation requirementsM24 Stud Bent GAL bolts in concrete footing

NotesThe SmartPoleTM by HUB is a track based system that relies on a unique aluminium extrusion to achieve its functionality. Accessories fix to the pole by utilizing this track which provides a discrete connection detail. The SmartPoleTM by HUB is available in two sizes and is finished at ground level with a cladding solution that provides additional benefit.


Banner Poles


hiSToRYTheSmartPole™wasconceivedbytheCityofSydneyin1997aspartoftheambitiousstreetscapeupgradeprogramthatwasplannedinpreparationfortheSydneyOlympics,2000.Thesimpleintentwastodevelopapolesystemthatwouldallowmultiplepolemountedaccessoriestobeaccommodatedonasinglepole,thusreducingtheclutterfromthepublicdomainthattypicallyaccumulatesinanybusyandgrowingcity.TheSmartPole™istheoriginalMultiFunctionalPolesystemandhaswonanAustralianDesignAwardinrecognitionofitsoriginalityandnoveltyofthisnewproductcategory.

Sinceitsinception,theSmartPole™continuestobesuccessfullyrolledoutthroughouttheCityofSydneyandmanyothercouncilsaroundAustraliaandinternationally.Itcontinuestomeettheevolvingneedsdemandedofatrulymultifunctionalpolesystemincontemporaryurbanenvironments.HUBStreetEquipmentiscurrentlytheexclusiveproviderofthissuccessful,patentedandprovensystem,theSmartPole™.

ovERviEWTheSmartPole™launchedacompletelynewproductcategorydesignedspecificallyforthepublicdomain.TheSmartPole™reducesstreetscapeclutterbyaccommodatingarangeofpolemountedaccessoriesontoasinglepolesystem.TheSmartPole™achievesthismulti-functionalitythroughapatentedtrackdetailintegrallyformedintothepole.Thistrackprovidesthefixingdetailintowhichafullrangeofaccessoriescanbeconnected.Thisrangeofaccessoriesincludes,butisnotlimitedto,streetlighting,banners,pedestrianlighting,CCTV,telecommunicationstechnology,featurelighting,trafficsignals,VMS,signage,pedestriansignals,etc.

SYSTEMTheSmartPole™byHUBisatrackbasedsystemthatreliesonauniquealuminiumextrusiontoachieveitsfunctionality.Accessoriesfixtothepolebyutilizingthistrackwhichprovidesadiscreteconnectiondetail.TheSmartPole™byHUBisavailableintwosizesandisfinishedatgroundlevelwithacladdingsolutionthatprovidesadditionalbenefit.

Streetlight Outreach

ZONE 35 - 10m

ZONE 22 - 5m

ZONE 1 0 - 2m

ZONE 0Under-ground

CCTV

Feature Lighting

Kerbside Multi


Long Arm Sign

Pedestrian Push Button

Conduits Concrete Reinforced Footing

Tra c MonitoringTechnology

Power Terminal Board

Feature Lighting

Wa

Tra c Lantern Outreach

Pedestrian Lighting

Banner

Pedestrian Lantern

Tra c Lantern

Audio Unit

Flower Basket Outreach

Antenna

Solar

Microcell

VMS

Streetname Sign

Outreach Sign

Kerbside Single

Tra c Terminal Board

Access Hatch

Anchor Bolts

AccESSoRiESTheSmartPole™byHUBisatrulymulti-functionalpolesystemthatisdesignedtoaccommodateafullrangeofpolemountedaccessoriesthataretypicallydeployedwithinthepublicdomain.Theseaccessoriescanbecategorizedunderoneofthefollowingheadings:Lighting,Traffic,andSignage&Telecommunications.

lightingTheSmartPole™byHUBcanaccommodatethefullrangeoflightingtypesthatmayberequiredwithinthepublicdomain.Thisincludesstreetlighting,pedestrianlighting,featurelighting,safetylightingandspotlights.

TrafficTheSmartPole™byHUBhasachievedfullRMScompliancesocanaccommodatethefullsuiteofRMSaccessoriesincludingtrafficandpedestriansignals,signage,camerasandtrafficsignaloutreachesto10m.

SignageTheSmartPole™byHUBcanalsoaccommodateabroadrangeofsignagetypes.Thisincludesstreetnames,trafficcontrol,RMSsignage,parkingcontrol,pedestriansignage,directionalsignageinadditiontoreal-time-display,bannersandelectronicsignage.

TelecommunicationsAbroadrangeoftelecommunicationstechnologiescanalsobeaccommodatedontheSmartPole™byHUB.CCTV,trafficcameras,micro-cellsandreal-time-displaypanelsaresomeofthemorecommonaccessoriesthatfallwithinthiscategory.

Multi-Function PolEssmartPoletM







ZONE 35 - 10m

ZONE 22 - 5m

ZONE 1 0 - 2m

ZONE 0Under-ground

CCTV

Feature Lighting

Kerbside Multi


Long Arm Sign





Feature Lighting

Wa


Pedestrian Lighting

Banner

Pedestrian Lantern

Tra c Lantern

Audio Unit


Antenna

Solar

Microcell

VMS

Streetname Sign

Outreach Sign

Kerbside Single


Access Hatch

Anchor Bolts













ZONE 35 - 10m

ZONE 22 - 5m

ZONE 1 0 - 2m

ZONE 0Under-ground

CCTV

Feature Lighting

Kerbside Multi


Long Arm Sign





Feature Lighting

Wa


Pedestrian Lighting

Banner

Pedestrian Lantern

Tra c Lantern

Audio Unit


Antenna

Solar

Microcell

VMS

Streetname Sign

Outreach Sign

Kerbside Single


Access Hatch

Anchor Bolts









November 2020 p47

Type 01 Drinking fountain

SpecificationExisting drinking fountain 1500mm heightTwo anti-bacterial bottle refill dispensersDDA-compliant wheelchair-accessible designCustomisable graphic panels with anti-graffiti protectionRemovable panel for easy filter replacementTwo year warranty

Materials Stainless steelAnodised steel

Finishes 2B


Proprietary product Aquafil 1500mm Refill Station and Drinking Fountain

SupplierCiviq (https://www.civiq.com.au)

Installation requirementsAnchor bolts to concrete base

NotesFilter unit option: Sub-micron or 5 micronFilter unit working pressure: 10-125 psi (0.7-8.5 bar), non-shockWater supply connection: 1/2 inch supply line with 1/2 inch male BSP connectionDrainage: 50mm PVC

Drinking Fountains


p48 November 2020


Fence

Type 01 Fence

SpecificationOrdinance timber fence with top and bottom railDimensions to match existing

Materials Timber

Finishes Paint - Biscuit and Brunswick Green



SupplierN/A

Installation requirementsUpright posts to be set into concrete foundation

NotesNA



November 2020 p49

Type 02 Fence

SpecificationPedestrian fence Height varies - minimum 1150m

Materials Hot dipped galvanized steel

Finishes Powder coated - ironstone matt colour

PrecinctUrban roadsCoastal roads

Proprietary product RMS Pedestrian Fence 1

SupplierEncat (http://www.encat.com.au)

Installation requirementsIn ground or base plate mounting

NotesNA

Fence


p50 November 2020


Adshel style EVO MKIV selected made by Stoddart Infrastructure Finished in powder coated IronStone Matt

Pattern (urban) expected that this will be used as the on glass etching.helps prevent graffiti and vandalism.

Frosted appearance.

§ Adshell style EVO MKIV selected - 3 Bay Advertising Shelter consistent with most locations

§ Square simple shapes with light structure matches better with signage brand and style aesthetics

§ Glass roof structures add more light and open feeling to street scape.

§ etched pattern on glass to be consistent with urban sign style graphic

§ design will look similar to image at right, colour will be darker to match the Dulux Ironstone Matt

Mosman Council Public Domain Concepts

Bus Shelters

Adshel style EVO MKIV - Bus Shelter

Specification3 Bay Advertising ShelterSquare simple shapes with light structure Glass roof structures

Materials Powder Coated Aluminium frameToughened safety glass

Finishes Powder Coated Aluminium Frame (IronStone Matt)Etched pattern (Urban) on glass, consistent with sign style graphic. Frosted appearance

PrecinctConsistent with most locations

Proprietary product Adshel style EVO MKIV

SupplierStoddart Infrastructure (http://www.stoddart.com.au)

Installation requirementsConcrete base

NotesOverall dimension (mm): 4230W x 1600D x 2565HInternal dimension (mm): 3835W x 600D x 2350HSeat length: 1800mm

Bus Shelter

INFRASTRUCTURE

STANDARD PRODUCT

P: 1300 557 654W: stoddartinfrastructure.com.auE: [email protected]

Copyright Stoddart Infrastructure. All rights reserved.

250

0

500

227

5

75 1279 1279 1279

-

- 1

JDP 04/03/2015

-

-574 Plummer St

A

--

1:30

A3

COPYRIGHT STODDART INFRASTRUCTURE 2016. The information contained in this document is the sole property of Stoddart Infrastructure. Any reproduction in part or whole without written permission of Stoddart Infrastructure is prohibited.

REV:

ISSUE:

MATERIAL:

FINISH:

DRAWING TYPE:

QUOTE/PROJECT NO:

DRAWN BY: DATE:REVISED BY: DATE:

DRAWING TITLE:

SIZE:SHEET:

SCALE:

T: 1300 557 654 | W: stoddartinfrastructure.com.au

STD:

ISO

DRAWING NO:VIC 3207

REV BYAS DRAWNA1DESCRIPTION

Port Melbourne,

JDP

Stoddart A3 Template

0101 Evo MkII 01-01

Suite 27, CAD GENERATED DRAWINGDIMENSIONS IN MILLIMETRESDO NOT SCALE

1600

585

4230

Dimensions (mm):Overall: 4230W x 1600D x 2500HInternal: 3840W x 585D x 2275HSeat length: 1800

Finishes:Powder Coated Aluminium FrameRefer to Dulux Powder Coat colours

Features: Toughened safety glass Aluminium roofCantilever seatSeat arm-restsWindbreaksConcealed footings

Optional extras:Mesh wall panelsLED lighting (mains or solar)Walk throughBolt to surface

EVO MKII SHELTER

FRONT VIEW SIDE VIEW

INFRASTRUCTURE

STANDARD PRODUCT

P: 1300 557 654W: stoddartinfrastructure.com.auE: [email protected]

Copyright Stoddart Infrastructure. All rights reserved.

250

0

500

227

5

75 1279 1279 1279

-

- 1

JDP 04/03/2015

-

-574 Plummer St

A

--

1:30

A3

COPYRIGHT STODDART INFRASTRUCTURE 2016. The information contained in this document is the sole property of Stoddart Infrastructure. Any reproduction in part or whole without written permission of Stoddart Infrastructure is prohibited.

REV:

ISSUE:

MATERIAL:

FINISH:

DRAWING TYPE:

QUOTE/PROJECT NO:

DRAWN BY: DATE:REVISED BY: DATE:

DRAWING TITLE:

SIZE:SHEET:

SCALE:

T: 1300 557 654 | W: stoddartinfrastructure.com.au

STD:

ISO

DRAWING NO:VIC 3207

REV BYAS DRAWNA1DESCRIPTION

Port Melbourne,

JDP

Stoddart A3 Template

0101 Evo MkII 01-01

Suite 27, CAD GENERATED DRAWINGDIMENSIONS IN MILLIMETRESDO NOT SCALE

1600

585

4230

Dimensions (mm):Overall: 4230W x 1600D x 2500HInternal: 3840W x 585D x 2275HSeat length: 1800

Finishes:Powder Coated Aluminium FrameRefer to Dulux Powder Coat colours

Features: Toughened safety glass Aluminium roofCantilever seatSeat arm-restsWindbreaksConcealed footings

Optional extras:Mesh wall panelsLED lighting (mains or solar)Walk throughBolt to surface

EVO MKII SHELTER

FRONT VIEW SIDE VIEWBus shelter installed

Front and side viewsGlass pattern

Adshel style EVO MKIV selected made by Stoddart Infrastructure Finished in powder coated IronStone Matt

Pattern (urban) expected that this will be used as the on glass etching.helps prevent graffiti and vandalism.

Frosted appearance.

§ Adshell style EVO MKIV selected - 3 Bay Advertising Shelter consistent with most locations

§ Square simple shapes with light structure matches better with signage brand and style aesthetics

§ Glass roof structures add more light and open feeling to street scape.

§ etched pattern on glass to be consistent with urban sign style graphic

§ design will look similar to image at right, colour will be darker to match the Dulux Ironstone Matt

Mosman Council Public Domain Concepts

Bus Shelters


Project description 00 Month 2020 Issue: Draft

BLANK PAGE


Project description 00 Month 2020 Issue: Draft


Documents

Mosman Council Public Domain Manual