MSG9000 Local EMS Installation Guide
(V2009-01)
ZTE CORPORATION
Revision Record
Document No.
Version No.
Drafted by/Modified by
Examined by
Drafted/Modified on
Reasons
Major Modifications (Key Points)
N/A
V2009-01
Wen Haixin
Jiang Haijun
2009-5-27
MSG9000 commissioning SOP
Draft
Contents
11 General Description of SOP
22 Netnumen Server Software Installation
22.1 Overview
22.2 NetNumen Software Installation
72.3 NetNumen Software Configuration
122.4 NetNumen Database Installation
183 NM System Running
183.1 Overview
183.2 Startup of Server Software
193.3 Startup of Client Software
214 Installation of NetNumen Client Software on Remote EMS
Server
1 General Description of SOP
Purpose
Install the EMS of MSG9000.
Prerequisites
The local EMS and Server 129 are installed on the same server.
The server has been installed with Windows 2003 Server Chinese
version + SP2 patch, and SQL Server 2005 Chinese version.
Procedure Description
Perform the installation of local EMS according to Chapter 2 and
3. For the installation of client software on remote EMS server,
refer to Chapter 4.
2 Netnumen Server Software Installation
2.1 Overview
This chapter introduces the installation and configuration of
NetNumen software and database on the server.
2.2 NetNumen Software Installation
Purpose
Set up the software program part of NetNumen NM server to make
it able to manage NEs and serve the NetNumen client.
Prerequisites
Windows 2003 Server Chinese version and SQL Server 2005 Chinese
version have been installed.
Tools
MSG9000 version files
Procedure Description
1. Unzip the NetNumenN31-V4 software installation package to the
target disk partition. To avoid a long installation directory,
please directly unzip it to the first level directory of the
partition, for example, to the D:\EMS directory. The installation
source directory of unzipped version is shown in the Figure
2.21.
Figure 2.21 Contents of Installation Package
2. Click to run the installation file install.bat, and the
Figure 2.22 pops up. Begin the version installation.
Figure 2.22 Language Selection
3. To install the Chinese version, input 2; to install English
version, input 1. The language selected here should be consistent
with that on Figure 2.31, otherwise the user cannot log on to the
client.
Figure 2.23 Installation Directory Setting
4. Input the target installation directory of NetNumenN31. And
then press the Enter key.
Figure 2.24 Installation Type Selection
5. Select the Type 2 Client and Server, as shown in the Figure
2.24. And then press the Enter key to unzip the package.
Figure 2.25 Unzip the Package
6. It takes a long time to unzip the package, please wait
patiently. After all version files are unzipped, the installation
program automatically starts the configuration center of
NetNumenN31 software.
Figure 2.26 Configuration Center
Subsequent Procedure:
Software configuration: after all version files are unzipped,
the installation program automatically starts the configuration
center of NetNumenN31 software.
The configuration center can also be started manually, with the
startup path shown in the Figure 2.27.
Figure 2.27 Startup Path of Configuration Center
2.3 NetNumen Software Configuration
Purpose
Configure the NetNumen software to make it connect to SQL
database, and ensure the network between NetNumen and NEs/client is
normal.
Prerequisites
NetNumen software has been installed successfully.
Procedure Description
1. Check the basic configuration:
View the Basic Information in the NetNumen Config Center window,
as shown in the Figure 2.31. Select the language in which the
NetNumenN31 system is running. The selected language should be
consistent with that in software installation in Figure 2.22. Click
the Save button.
The right pane shows the NM software version and OS related
information.
Figure 2.31 Configuration Center Basic Information
2. Click NE Module in the NetNumen Config Center window and then
select the NE ZXMSG 9000 to be managed by the installed
NetNumenN31.
Figure 2.32 Configuration Center NE Module
Click Save. The Set Successfully prompting dialog box
appears.
3. Click Database Configuration in the NetNumen Config Center
window to set the connection parameters of the NetNumenN31
database.
(1) Select MS SQL Server as the Database Type.
Figure 2.33 Configuration Center Database Configuration
(2) Set the logon password of database system administrator sa.
By default, the password is netnumen. If the sa password of
currently installed SQL Server database is not the default
netnumen, please use the existing password. Modify relevant
settings of NetNumenN31 according to current sa password of SQL
Server via the Configuration Center, as shown in the figure below.
Double click the Value column of Database System Administrator
Password to modify the sa password of the current SQL Server. For
other parameters shown in the Figure 2.34, keep the default
settings. Click the Save button.
Figure 2.34 Database Configuration Modification
4. Click Short Cut in the NetNumen Config Center window to enter
the Short Cut window.
Figure 2.35 Configuration Center Short Cut
Click the Save button after the configuration, as shown in the
Figure 2.35. Then click the Close button to finish the
configuration.
2.4 NetNumen Database Installation
Purpose
Initialize the database and realize the connection with
database.
Prerequisites
NetNumen software configuration has been finished.
Procedure Description
1. Check the SQLCMD.exe environment variables: open the windows
command line window and execute the command sqlcmd. Observe the
execution result.
If the result is as shown in the Figure 2.41, it indicates the
environment variables have been loaded and you can start the
installation of database.
Figure 2.41 Check Environment Variables Loaded
If the result is as shown in the Figure 2.42, it indicates the
environment variables are not loaded and you need to perform the
following steps.
Figure 2.42 Check Environment Variables Unloaded
Search the SQLCMD.exe file under the SQL Server 2005
installation directory and add its directory to the system
environment variable.
Figure 2.43 Add Environment Variable
2. Start the NetNumen N31 Init Database shortcut, with the path
shown in the Figure 2.44.
Figure 2.44 Start Path of Database Installation Program
Click Initialize Database and the window pops up, as shown in
the Figure 2.45.
Figure 2.45 Database Installation Window
3. Input Y and press the Enter key to begin the initialization
of database.
The system prompts Build successful. At this time you can
complete the initialization of database by putting any key.
Figure 2.46 Database Installation Completed
4. Start the NetNumenN31 Config Center and enter the Database
Configuration window, as shown in the Figure 2.47.
Figure 2.47 Test Database Connection
The test result Connecting database is complete successfully
indicates the previous database initialization is successful. The
installation of server is finished.
3 NM System Running
3.1 Overview
Firstly start the server software and then client software.
3.2 Startup of Server Software
Purpose
Start the NM server software and verify the correctness of
installation.
Prerequisites
The client and server have been installed successfully.
Procedure Description
1. There are two shortcuts NetNumen N31 Server and NetNumen N31
Client on the Windows desktop.
Figure 3.21 Desktop Icon of NM Server
2. Double click the shortcut of NetNumen N31 Server to start the
NetNumen unified management system console. In the case of default
configuration, the console automatically starts the NetNumen
network management process, CORBA notification service process, and
FTP process (NetNumen assistant process). After the service
processes are started, a green icon appears on the window.
Figure 3.22 Management System Console Startup Completed
3.3 Startup of Client Software
Purpose
Run the client and manage NEs.
Prerequisites
The installation of NM server software has been completed.
Procedure Description
1. Double click the shortcut of NetNumen N31 client on the
desktop and a window pops up, as shown in the Figure 3.3-1.
Figure 3.31 Logon Window of Client
2. Click the OK button, and the startup is completed. As shown
in the Figure 3.32.
Figure 3.32 Management Window of NetNumen
4 Installation of NetNumen Client Software on Remote EMS
Server
Purpose
Install the NetNumen client on remote EMS server.
Prerequisites
NetNumen server has been installed. The computer on which the
client is to be installed has been installed with Windows XP
system. The client and local server are in the same network segment
or the client can access the local server.
Procedure Description
1. Compress the server installation files ums-clnt, jdk-windows
and upgradeN31 into a package as the client program. The file
structure is as shown in the figure below.
Figure 3.31 NM Directory Structure
2. Copy the client program to other computers and then delete
the ums-clnt\temp directory.
1-1
1-2
iii
All Rights reserved, No Spreading abroad without Permission of
ZTE
