Upload
doanquynh
View
217
Download
0
Embed Size (px)
Citation preview
-1-
INSTALLATION INSTRUCTIONSNo. 59-1935-1
MULTI DIMENSIONAL OUTDOOR DETECTORMULTI DIMENSIONAL OUTDOOR DETECTOR
VX InfinityTM seriesVX InfinityTM series
FEATURES
CONTENTS
VXI-ST Standard model with 2 PIR
WIRED MODEL
VXI-AM VXI-ST with anti-masking
VXI-DAM VXI-AM with micro-wave
The VX InfinityTM series provide highly reliable detection functions, reducing false reports or report losses. The VX InfinityTM series deliver stable detection performance even in severe outdoor environments.
- 12 m (40 ft.) by 90 degree flexible detection pattern adjustable to 5 ranges - SMDA Logic for advanced temperature compensation and environmental noise immunity.- Easy Masking for over spill prevention - Double Conductive Shielding against bright light disturbance. - Conduit/TX-Battery Case for both wired and wireless-ready models.
BASIC FEATURES
- Active IR Anti-Masking for detecting covering objects - Tough Mod Dual Technology based on OPTEX gold-plated microwave module
OPTIONAL FEATURES
INTRODUCTION 1-1 BEFORE INSTALLATION1-2 PARTS IDENTIFICATION1-3 DETECTION AREAINSTALLATION2-1 BEFORE MOUNTING2-2 WALL TAMPER WRS-02 (OPTION)2-3 MOUNTING2-4 MOUNTING WITHOUT BACK BOX2-5 MOUNTING WITH BACK BOX2-6 WIRING2-7 PLUG-IN END OF LINE RESISTORS (EOL) (OPTION)2-8 AREA ANGLE ADJUSTMENT
1
2
234
44556778
89
101213
141415
3456
7
2-9 AREA MASKING2-10 DETECTION LENGTH ADJUSTMENTSWITCH SETTINGWALK TESTLED INDICATIONSPECIFICATIONS6-1 SPECIFICATIONS6-2 DIMENSIONSSETTING OF SPECIAL DETECTION AREA
-2-
Warning
INTRODUCTION11-1 BEFORE INSTALLATION
Warning
Caution
Failure to follow the instructions provided with this indication and improper handling may cause death or serious injury.
Failure to follow the instructions provided with this indication and improper handling may cause injury and/or property damage.
The check mark indicates recommendation.
The nix sign indicates prohibition.
• Sunlight and reflection • Heat source • Objects moving in the wind
0.8 – 1.2 m(2.64 – 3.94 ft)
Parallel
Tilt
Do not remove the PCB. Keep product away from direct splash.
Mounting height. Keep the detector parallel to the ground.
Consider the direction a person is approaching from, as well as the detection area.
Install the detector in a place where it is free from false alarm factors. For example:
-3-
Cover unit
Main unit
Back box
Back box cap
Wiring sponge
Mounting plate
1-2 PARTS IDENTIFICATION
-Precautions for installing two or more sensors
Masking seal × 3 pcsFor wall mountingScrew kit
Screw (4 × 20 mm)
Optional accessories
Wall tamper (WRS-02) PLUG-IN EOL (PEU)
1.0 m (3.28 ft) or more Less than 1.0 m (3.28 ft)
Do not install two or more VXI-DAMs in side by side or face to face. Doing so may cause malfunction. VXI-DAM may be installed in back to back. If mounting on the same wall, make sure that each unit is at least 1.0 m (3.28 ft) apart from the other.
VXI-STVXI-AM
VXI-DAM
-4-
a
b
c
d
ef
g hi
j
l
m
n
k
INSTALLATION2
1-3 DETECTION AREA
2-1 BEFORE MOUNTING
Control panelWall tamper (option)WRS-02
Twist and swage the wires.
TOP VIEW
SIDE VIEWLength limiting position 1 (Default)
PIR
MW
Area diagram of horizontal position D
12m
12m 10m 12m10m5m 5m0
10m
5m
0
DA B C E F G
WRS-02 (option)
1m
0 5m 10m 12m
Length limiting position 2
1m
0 5m 10m 12m
Length limiting position 3
1m
0 5m 10m 12m
Length limiting position 4
1m
0 5m 10m 12m
Length limiting position 5
1m
0 5m 10m 12m
Note>>The maximum detection length may vary asshown below due to environment conditions.
Remove the cap.1 Open the cover unit.2 Remove the main unit from the back box.
3 Remove the back box from the mounting plate.
4
Mount the wall tamper (WRS-02) on the back of the main unit.
1 Run the wire along the wiring groove.
2 Install the unit on the terminal block and control panel.
3
Store the connecting cable in a trench and seal with a label already in place.
2-2 WALL TAMPER WRS-02 (OPTION)
-5-
2-3 MOUNTINGMount the mounting plate.
2-4 MOUNTING WITHOUT BACK BOXThe unit is installed without a back box unless the main unit requires a protrusion off the mounting wall.
Mount the main unit on the mounting plate.
Wall mount Pole mount
Electric gang box mount Conduit installation
Metal band
* Use a metal band with 25 mm or less in width.
Pitch 83.5 mm (3.29 inch)
An electric gang box can be connected. Open the knockout located at the bottom of the back box.
Connect the pipe and back box.
When mounting to electric gang box (single), follow wall mount instructions.
Wiring hole
Wiring holeWiring hole
Wiring sponge
Note>>Pay attention to warterproof.
Note>>It is optional to use the Backbox in hardwired models.
ø 21 mm
2-6Proceed to
-6-
2-5 MOUNTING WITH BACK BOXWhen a certain distance from the mounting surface is required for purposes such as avoiding an unwanted object, use the back box to install the unit.
Open a wiring knockout on the back box and pass the wire from the mounting plate.
Wiring
Put the top of the back box on the hook.
Wiring hole
Wiring sponge
Wiring sponge
1.
2.
3.
Wiring hole
1 Open a wiring knockout inside the back box.
2 Mount a back box on the mounting plate.
3 Mount the main unit on the back box. 4 Put the cap on top.
-7-
2-6 WIRING
-Power cable length
The power cable should be limited to the following length.
Wiring terminal is located on the upper part of the main box.
-When setting the resistance value using PLUG-IN EOL
Three types of signals - ALARM, TROUBLE, and TAMPER - can be recognized through the combination of the resistance value and wires for the TR, COM, and TP terminals.
-When setting the resistance value withoutusing PLUG-IN EOLWire resistors between the appropriate terminals as follows:
This feature may be used when connecting VXI to a control panel that supports the EOL technique.
Terminals<VXI-ST>
Pow
er (+
)P
ower
(-)
Spa
reS
pare
Ala
rmA
larm
Tam
per
Tam
per
Aux
. inp
utA
ux. i
nput
<VXI-AM> <VXI-DAM>
Pow
er (+
)P
ower
(-)
Spa
reTr
oubl
eC
omm
onA
larm
Tam
per
Tam
per
Aux
. inp
utA
ux. i
nput
WIRE GAUGE
AWG22(0.33mm2)
290 m(950 ft)
620 m(2,030 ft)
240 m(790 ft)
520 m(1,710 ft)
160 m(520 ft)
360 m(1,180 ft)
12 V
VXI-ST VXI-AM VXI-DAMCurrent draw 20 mA Current draw 24 mA Current draw 35 mA
14 V 12 V 14 V 12 V 14 V
450 m(1,480 ft)
980 m(3,220 ft)
380 m(1,250 ft)
820 m(2,690 ft)
260 m(850 ft)
560 m(1,840 ft)
720 m(2,360 ft)
1,570 m(5,150 ft)
600 m(1,970 ft)
1,310 m(4,300 ft)
410 m(1,350 ft)
900 m(2,950 ft)
AWG20(0.52mm2)
AWG18(0.83mm2)
COMMONTROUBLE
ALARMTAMPER
TypeInsert direction
A
Caution>>For details, refer to a note provided with plugs. Make sure to apply thecorrect type of plug according to the system
+ - SP TR COM AL TP TP
Triple-EOL
Double-EOL
TAMPERALARMTROUBLEPLUG-IN EOL
CONTROL PANEL
+ - SP TR COM AL TP TP
TAMPERALARMTROUBLE
2-7 PLUG-IN END OF LINE RESISTORS (EOL) (OPTION)
-8-
2-8 AREA ANGLE ADJUSTMENT
2-9 AREA MASKING
Note>>When creating a special detection area, refer to the end of this manual.
If there is an unwanted object within the detection area, apply an area masking label to the appropriate area.
Insert the protruding part of the cover into the lens hole.
Fit the edge of the lens.
Slide the lens holder to secure it.
Horizontal position D (Default)
Horizontal position B (F: symmetrical position)
Horizontal position C (E: symmetrical position)
Horizontal position A (G: symmetrical position)
DA B C E F G DA B C E F G
DA B C E F GDA B C E F G
DA B C E F G
DA B C E F GDA B C E F G
or
oror
Unwantedobject (Tree)
1 Slide the lens holder and remove the lens holder out of the cover as shown below.
2 Identify positions to mask on the lens and apply a corresponding strip from the masking sheet 1.
3 Insert the lens into the cover. 4 Mount the lens holder to the cover.
The angle can be adjusted in 7 levels from A to G.
The detection area becomes 14 zones only when A or G is selected.
-9-
2-10 DETECTION LENGTH ADJUSTMENT
Both upper and lower detection area are blocked
IMPORTANTBOTH DETECTION AREAS MUST BE
BLOCKED FOR DETECTION
Detection!
NODetection
NODetection
Only upper detection area is blocked
Only lower detection area is blocked
MW sensitivity adjustment knob
1 Adjust the PIR detection length by sliding the lower PIR to the desired position.
2 Adjust the MW detection length by rotating the MW sensitivity adjustment according to the PIR area.
Detection length setting chart
* The detection lengths described above should be used as a guideline.
Position
1(Factorydefault)
2
3
4
5
12.0 m(40.0 ft)
8.5 m(27.9 ft)
6.0 m(19.7 ft)
3.5 m(11.5 ft)
2.5 m(8.2 ft)
10.0 -17.0 m(32.1 - 55.8 ft)
7.0 - 12.0 m(23.0 - 39.4 ft)
5.0 - 8.5 m(16.4 - 27.9 ft)
3.0 - 6.0 m(9.8 - 19.7 ft)
2.0 - 3.5 m(6.6 - 11.5 ft)
Max detection length Detection areaMW
sensitivityadjustment
12 m
8.5 m
6 m
3.5 m
2.5 m
-10-
DIP switch1 LED2 ALARM OUTPUT3 AUX INPUT4 ANTI-MASKING5 MICROWAVE IMMUNITY
SWITCH SETTING3
1
ON
24
53
ON1
23
45
DIP switch 1
OFF ⇔ ON
-LEDVXI-STVXI-AM
VXI-DAM
POSITION FUNCTION
ON(Factory default)
OFF
LED ON
LED OFF
DIP switch 2
N.C. ⇔ N.O.
-ALARM OUTPUTVXI-STVXI-AM
VXI-DAM
ON1
23
45
POSITION FUNCTION
N.O.
N.C.(Factory default)
N.O. output
N.C. output
VXI features can be set on/off by DIP switch settings.
MW sensitivity adjustment
PIR sensitivity selector
-11-
DIP switch 3
AND ⇔ OR
-AUX INPUTVXI-STVXI-AM
VXI-DAM
ON1
23
45
POSITION FUNCTION
OR
AND(Factory default)
When either the main unit or the secondary detect someone,the alarm is activated.
When both the main unit and the secondary detect someone,the alarm is activated. Choose the setting when a secondaryunit is not connected.
DIP switch 4
OFF ⇔ ON
-ANTI-MASKINGVXI-STVXI-AM
VXI-DAM
ON1
23
45
POSITION FUNCTION
OFF
ON(Factory default) ANTI-MASKING ON
By connecting a secondary unit (another warning sensor), you can extend the detection area and correct false alarms. The secondary unit must have a voltage free N.C. output such as another PIR detector or AIR detector.<Infrared (AIR) sensors, thermal line (PIR) sensors, magnet switches, etc.>
ANTI-MASKING OFF
When masking condition continues more than 3 minutes, TROUBLE will be generated.TROUBLE is generated after 20 seconds under the anti-masking test mode.
Teaching mode starts when both the separate box cover and the main unit cover are attached.Please be careful not to leave any object within 1 m from the unit.
<ANTI-MASKING function>
ANTI-MASKING test modeThe trouble is output after 20 seconds.
Normal modeThe trouble is output after 3 minutes.
10 minutes1 minute
Teaching
Note>>The alarm is activated only if both the main unit and the socondary unit is activatedwithin 60 sec.
In OR mode, a secondary detector must be fitted. If not fitted, the unit will generatean alarm continuously.
-12-
DIP switch 5
STD ⇔ IMMUNITY
-MICROWAVE IMMUNITYVXI-STVXI-AM
VXI-DAM
ON1
23
45
POSITION FUNCTION
IMMUNITY
STD(Factory default)
MICROWAVE IMMUNITY logic is activated. Use this under harsh environment (e.g. vegetation sway).
MICROWAVE IMMUNITY logic is not activated.
PIR SENSITIVITY SELECTOR-PIR SENSITIVITYVXI-STVXI-AM
VXI-DAM
POSITION FUNCTION
HIGH
MIDDLE(Factory default)
High sensitivity
LOW Low sensitivity
Middle sensitivity
HIGH
MIDDLE
LOW
WALK TEST4
Check that the cover is completely closed.
ON1
23
45
ON1
23
45
Note>>The switch is set to “ON” by factory default.
Note>>For the walk test, make a motion at a distance more than1.0 m (3.28 ft) away from the detecter.
Detected Not detected
1 Set the DIP switch 1 (LED) to “ON”. 2 Attach the main unit cover.
3 Check that LED lights for 2 seconds when the intended object is detected.
4 If the LED does not need to be turned on at all times, set the DIP switch 1 (LED) to “OFF”.
-13-
LED INDICATION 5
REDYELLOW
(VXI-DAM only)Blink Light OFF
<VXI-ST> <VXI-AM>
<VXI-DAM>
Detector condition LED indicator
Warm-up
Blinks for approx. 60 seconds.
AlarmLights for 2 seconds.
Masking detection(VXI-AM only)
Blinks 3 times and then repeats.
Note>>The LED blinks even if the DIP switch 1 (LED) is set to “OFF”.
Detector condition LED indicator
Warm-up
Blinks for approx. 60 seconds.
AlarmRED LED lights for 2 seconds.
MW detectionYELLOW LED lights for 2 seconds.
Masking detection
Blinks 3 times and then repeats.
Note>>The LED blinks even if the DIP switch 1 (LED) is set to “OFF”.
RED YELLOW
-14-
SPECIFICATIONS 66-1 SPECIFICATIONS
VXI-DAMVXI-AMVXI-STModel
Passive infrared & MicrowavePassive infraredDetection method
12.0 m (40 ft) 90° wide / 16 zonesPIR Coverage
12 – 2.5 m (5 levels)PIR distance limit
0.3 – 1.5 m/s (0.98 – 4.92 ft/s)Detectable speed
2.0°C (3.6°F) at 0.6 m/sSensitivity
9.5 – 18 V DCPower input
Current draw 20 mA (max.)at 12 V DC
24 mA (max.)at 12 V DC
35 mA (max)at 12 V DC
2.0 ±1 sec.Alarm period
Approx. 60 sec. (LED blinks)Warm-up period
N.C. / N.O. Selectable 28 V DC 0.1 A (max)
N.C. 28 V DC 0.1 A (max)
Alarm output
N.C. 28 V DC 0.1 A (max) open when cover removed.Tamper output
Trouble output
LED indicator Red: Warm-up, alarm, masking detection (VXI-AM only) Red: Warm-up, alarm, masking detection.Yellow: Warm-up, MW detect.
No alarm 10 V/mRF interference
-30 – +60°C (-22 – +140°F) -20 – +60°C (-4 – +140°F)Operating temperature
95% max.Environment humidity
IP55International protection
Wall, Pole (Outdoor, Indoor)Mounting
0.8 – 1.2 m (2.64 – 3.94 ft)Mounting height
500 g (17.7 oz.)Weight 600 g (21.2 oz.)
Accessories Screw (4×20 mm) ×2 , Wiring sponge ×3 , Masking seal ×3
*Specifications and designs are subject to change without prior notice.
6-2 DIMENSIONS
Unit: mm (inch)
-
Pitch=83.5(3.29)
70.9 (2.80)
181.9(7.16)
64.5 (2.54)
71.3 (2.81)
105.5 (4.15)
185.9(7.32)
-15-
SETTING OF SPECIAL DETECTION AREA7Using masking seals 2 to 6, you can set a special detection area for the horizontal position A or G.
Masking seal 2
Masking seal 4
Masking seal 6
Masking seal 3
Masking seal 5
Area can be set only at the both sides.
Five patterns of special detection areas can be configured by applying a masking sticker.
1.5 × 10 m area can be set.
10 × 1.5 m area can be set.
5 × 10 m area can be set.
10 × 5 m area can be set.
Set to the desired area setting direction (horizontal position A or G).
When setting other than masking seal 1, cut off the knockout portion at the lower lens holder.
Select a masking seal from 2 to 6 according to the desired shape of area setting, and put it on the lens.
a
b
c
d
ef
g hi
j
k
l
m
n a
b
c
d
ef
g hi
j
k
l
m
n
a
b
c
d
ef
g hi
j
k
l
m
n
a
b
c
d
ef
g hi
j
k
l
m
n a
b
c
d
ef
g hi
j
k
l
m
n
12 m 12 m
12 m
10 m 10 m
10 m
5 m 5 m
5 m
12 m 12 m
12 m
10 m 10 m
10 m
5 m 5 m
5 m
12 m 12 m
12 m
10 m 10 m
10 m
5 m 5 m
5 m
12 m 12 m
12 m
10 m 10 m
10 m
5 m 5 m
5 m
12 m 12 m
12 m
10 m 10 m
10 m
5 m 5 m
5 m
Position G Position A
Position G Position A
Position G Position APosition G Position A
Position G Position A
Set to A or G
The lower detection area adjustment position must be “position 1” (12m) as default.
-16-
OPTEX INCORPORATED (USA)TEL:+1-909-993-5770Tech:(800)966-7839 URL:http://www.optexamerica.com/
OPTEX KOREA CO., LTD. (KOREA)TEL:+82-2-719-5971URL:http://www.optexkorea.com/
OPTEX SECURITY Sp.z o.o. (POLAND)TEL:+48-22-598-06-55URL:http://www.optex.com.pl/
OPTEX (DONGGUAN) CO., LTD.SHANGHAI OFFICE (CHINA)TEL:+86-21-34600673URL:http://www.optexchina.com/
OPTEX CO., LTD. (JAPAN)(ISO 9001 Certified)(ISO 14001 Certified)5-8-12 Ogoto OtsuShiga 520-0101JAPANTEL:+81-77-579-8670FAX:+81-77-579-8190URL:http://www.optex.co.jp/e/
OPTEX (EUROPE) LTD. (UK)TEL:+44-1628-631000URL:http://www.optex-europe.com/
OPTEX SECURITY SAS (FRANCE)TEL:+33-437-55-50-50URL:http://www.optex-security.com/
FCC ID : DC9 OPMW IC : 4012A-OPMWThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The VXI series is only a part of a complete system, therefore we cannot accept complete responsibility for any damages or other consequences resulting from an intrusion.
NOTE
The following statement will be provided with the equipment as required by Article 6.3 of the R&TTE Directive, 1999/5/EC.
The Optex VXI series are in conformity with all essential requirements of the R&TTE Directive (1999/5/EC). This equipment has been assessed to the following standards:EN 300 440-1: 2009EN 50130-4: 2004 including amendment 2: 2003EN 60950-1: 2006+A11: 2009
This product is marked with which signifies conformity with Class II product requirements specified in the R&TTE Directive.
The following table indicates countries and their appropiate microwave (MW) frequency. Do not use VXI-DAM/RDAM when the frequency does not meet the local requirement. For countries not included in this list, please consult the responsible Spectrum Management Agency.
Country of intended use AppropriateMW frequency
AppropriateMW frequencyCountry of intended use
Austria 9.900GHz Luxembourg 10.525GHzBelgium 10.525GHz The Netherlands 10.525GHzDenmark 10.525GHz Spain 10.525GHzFinland 9.900GHz Sweden 10.525GHzFrance 9.900GHz United Kingdom 10.587GHzGreece 10.525GHz Other non-EU: Iceland 10.525GHzIreland 10.587GHz Norway 10.525GHzItaly 10.525GHz Switzerland 9.900GHz
Note>>These units are designed to detect an intruder and activate an alarm control panel. Being only a part of a complete system, we cannot accept responsibility for any damages or other consequences resulting from an intrusion. These products confirm to the EMC Directive 2004/108/EC.
COMPLIANCE• VXI series complies with following Directives / Standards.
Directive: EMC Directive 2004/108/ECApplied Standards: EN 50130-4: 1995 +A1: 1998 +A2: 2003
EN 55022: 2006
• VXI-RDAM also complies with following Directives / Standardsmarked Class II, Directive: R&TTE Directive 1999/5/ECApplied Standards: EN 300 440-1: 2009
EN 300 440-2: 2009EN 301 489-1: 2008EN 301 489-3: 2002EN 50371: 2002EN 60950-1: 2006 +A11: 2009
The following table indicates the areas of intended use of the equipment and any known restrictions. For countries not included in this list, please consult the responsible Spectrum Management Agency.
FCC ID: DC9 OPMWWL IC: 4012A-OPMWWLThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.(2) This device must accept any interference received, including
interference that may cause undesired operation.
Country of intended useAustriaBelgiumDenmarkFinlandFranceGreeceIrelandItaly
LuxembourgThe NetherlandsSpainSwedenUnited KingdomOther non-EU: IcelandNorwaySwitzerland
13.700GHz10.525GHz10.525GHz13.700GHz10.587GHz10.525GHz10.587GHz10.525GHz
10.525GHz10.525GHz10.525GHz10.525GHz10.587GHz10.525GHz10.525GHz10,525GHz
Restrictions Country of intended use Restrictions
0700