ROMMEL A. RIVERA804 South Poblacion City of Naga Cebu

+966536558439Rarivera84@yahoo.com

WORK EXPERIENCE:

POSITION : Instrumentation technician Company : YANBU CEMENT COMPANY Address : YANBU, Al'madinah saudi arabia,KSA Inclusive Dates : November 25, 2012 up to Present

DETAILED JOB DESCRIPTION:

• Receive turn over reports from previous shifts.• After looking the reports see to it all things are to be implemented in the

shift.• If problem on electrical side occurs respond to the problems. Problem in

motors, motor control, overload problems, defective motors, solenoid valve, positioners and many others electrical related works.

• Prepare reports on plant operation with regards to E&I concerns at the end of shift

AREAS OF RESPONSIBILITY:

PREVENTIVE MAINTENANCE:• Conduct preventive maintenance on all field and panel mounting.• Perform calibration of measuring instruments and equipment.• Handle installation and commissioning of newly installed, replacement

and or additional instrumentation works.

CORRECTIVE MAINTENANCE:• Perform repairs, troubleshooting and calibration of all measuring,

indicating and controlling instruments and equipment’s.WORK EXPERIENCE:

POSITION : Instrumentation and Calibration TechnicianCompany : CEMEX Philippines (Apo Cement Corporation)Address : Brgy. Tina - an City of Naga, CebuInclusive Date : April 16, 2009 up to November 21, 2012

DETAILED JOB DESCRIPTION:

• Install, Calibrate, configure, troubleshoot and do preventive maintenance check-ups to all thermocouples, temperature switch and RTD's in plant especially use in protective machine interlock with the transmitter. (Endress+Hauser, Siemens, Sensetech, INOR, Hartmann and Braun)

• Install, calibrate, troubleshoot and do preventive maintenance check-ups to all pressure monitoring instruments in the plant including pressure

switch, pressure gauges, and differential pressure instruments with transmitter use in flow and pressure monitoring.

• Install, commissions, calibrate troubleshoot and do preventive maintenance check-ups to all positioners (motorized positioner, servo motors) use in dampers and swirler. (L. Bernard, AUMA).

• Calibrate, configure, troubleshoot and do preventive maintenance check-ups to all weigh feeders (Schenk and OAS).

• Install, commissions, calibrate, configure, troubleshoot and do preventive maintenance check-ups to all proximity sensors. (IFM PEPPERL+FUCHS).

• Install, commissions, calibrate, configure, troubleshoot and do preventive maintenance check-ups, and maintain level sensors use in silo's (Endress+Hauser, Siemens)

• Layout cable from instrument to panel boards up to I/O modules of PLC (Allen Bradley PLC).

• Install, commissions, calibrate, configure, troubleshoot and do preventive maintenance check-ups, and maintain vibration sensor use in motors in main drive and exhaust fans (Schenk Vibrocontroller).

• Calibrate, and do preventive maintenance check-ups to all gas analyzer in the plant ( Hartmann and Braun).

WORK EXPERIENCE:

POSITION : ElectricianCompany : JKLM Contractors IncorporatedAddress : 1024 EscañoSubd.Mabolo Cebu City, PhilippinesInclusive Date : January 20, 2009 to April 11, 2009

DETAILED JOB DESCRIPTION:

• Responsible for preparation of electrical devices..

• Install wiring devices for floor and ground fault current interrupting outlets.

• Install electrical lightings systems outlet, and lighting fixtures.

• Lay outing of PVC and plastic molding wiring method

• Armored cable and flexible hoses wiring method.

• RSC and EMT wiring method.

• Tightening of cables.

• Cable pulling.

CERTIFICATION AND TRAINING

General ElectricityBuilding Wiring and Motor Control Installation

Department of Manpower Development and Placement - DMDP

NATIONAL CERTIFICATE II (NCII)Building Wiring Installation

Technical Education and Skills Development Authority - TESDA

EDUCATIONAL ATTAINMENT:

Vocational Course : General Electricity Department of Manpower Development and Placement September 2008-2009

College : Bachelor of science in maritime Transportation October 2007

Secondary : Naga National High School Naga Cebu Philippines March 2001

Elementary : Naga Central Elementary school Naga Cebu Philippines March 1997

PERSONAL DATA:

Date of birth : April 14, 1984 Height : 5’5” Weight : 120 lbs. Gender : Male Civil status : Single

CHARACTER REFERENCES:

Engr. G.L.N Reddy Instrumentation manager YANBU CEMENT COMPANY- YANBU KSA

Engr. Jimmy Flores Instrumentation leader CEMEX Philippines (Apo Cement Corporation) Brgy. Tina-an City of Naga Cebu Philippines (032)489-3205/09157740155

Ariel S. Ignacio Instrumentation Superintendent CEMEX Philippines (Apo cement Corporation) Brgy. Tina-an City of Naga Cebu Philippines (032) 489-3205/ 09234366950