NEW MEXICO STATE UNIVERSITY - FIDEL...nmsu grants_fidel_anaeini.rvt new mexico state university - fidel nmsu fidel 1500 third st, grants, nm 87020-2025 design development issue date
GENERAL CONSTRUCTION NOTES1. THE CONTRACTOR IS RESPONSIBLE FOR THE GENERAL
PROVISIONS OF THE CONTRACT, INCLUDING GENERALAND SUPPLEMENTARY CONDITIONS.
2. THE CONTRACTOR SHALL COMPLY WITH (62-14.1 TO62.14-8 NMSA 1978), THE NEW MEXICO STATE CODEREGARDING LOCATION OF UTILITIES.
3. THE CONTRACTOR SHALL SUBMIT A WRITTEN REQUESTNO LESS THAN 14 DAYS PRIOR TO ANY REQUIREDINTERRUPTION OF POWER, WATER, SEWER,LABORATORY OR NATURAL GAS, STEAM, CHILLEDWATER, VACUUM, COMPRESSED AIR, HVAC; SECURITY,FIRE ALARMS OR SUPPRESSION, OR ANY OTHERSYSTEMS, OR WHICH WILL IMPEDE TRAFFIC, EMERGENCYEGRESS, OR VEHICLE ACCESS OF ANY KIND.
4. SITE CLEANING SHALL BE IN ACCORDANCE WITHSPECIFICATIONS.
5. DO NOT SCALE DRAWING. CONTRACTOR SHALL VERIFYALL CONDITIONS AND DIMENSIONS AT THE JOB SITE,AND IF ANY DISCREPANCIES ARE FOUND, THEARCHITECT SHALL BE NOTIFIED.
6. THE CONTRACTOR SHALL REPORT ANY DISCREPANCIESBETWEEN DRAWINGS AND SITE CONDITIONS TO THEARCHITECT BEFORE PROCEEDING WITH THE WORK. HESHALL VERIFY AND COORDINATE ALL FOUNDATION PLANDIMENSIONS WITH FLOOR PLANS AND SHALL BERESPONSIBLE FOR PROPER EXECUTION OF ALL WORK.
7. FINISH FLOOR ELEVATIONS ARE TO THE TOP OFCONCRETE OR PAVING UNLESS OTHERWISE NOTED.CEILING HEIGHT DIMENSIONS ARE TO FINISHEDSURFACES.
8. ALL DIMENSIONS ARE TO THE FACE OF CONCRETE, THECENTERLINE OF COLUMNS, THE FACE OF CONCRETEBLOCK WALLS, THE FACE OF EXTERIOR SHEATHING ANDTHE FACE OF STUDS UNLESS OTHERWISE NOTED.
9. ALL SYMBOLS AND ABBREVIATIONS USED ON DRAWINGSARE CONSIDERED TO BE CONSTRUCTION STANDARDSAND COMPLY WITH THE NATIONAL CAD STANDARDVERSION 3.1. IF THE CONTRACTOR HAS QUESTIONSREGARDING SAME, OR THEIR EXACT MEANING, FIRSTREFER TO THE NCS 3.1 AND THEN NOTIFY THE ARCHITECTTO REQUEST CLARIFICATION.
10. CONTRACTOR TO COORDINATE INSTALLATION OF ALLITEMS INDICATED AS OWNER SUPPLIED EQUIPMENTAND FURNISHINGS.
11. CONTRACTOR TO PROVIDE TEMPORARY HEATING /COOLING, SPACES THAT MUST REMAIN OPERATIONALDURING THE WORK. UTILITIES, AND SUPPORT ASREQUIRED FOR OWNER INSTALLED EQUIPMENT.
12. CONTRACTOR IS RESPONSIBLE FOR EROSION CONTROLDURING THE CONSTRUCTION PHASE, INCLUDING ANYPROVISIONS THAT MAY NEED TO BE TAKEN TO DIVERTSEDIMENT FROM LEAVING THE SITE AND ENTERINGADJACENT STREETS OF PROPERTIES. SUBMIT ANDOBTAIN A STORM WATER POLLUTION PREVENTION PLAN(SWPPP).
13. THE CONTRACTOR SHALL PROMPTLY CLEAN UP ANYMATERIAL EXCAVATED WITHIN THE RIGHT-OF-WAY SOTHAT THE EXCAVATED MATERIAL IS NOT SUSCEPTIBLETO BEING WASHED DOWN THE STREET OR INTO THESTORM DRAIN SYSTEM.
14. THE CONTRACTOR SHALL SECURE ALL REQUIREDPERMITS AS REQUIRED BY LOCAL AUTHORITIES, PRIORTO BEGINNING CONSTRUCTION.
15. PERFORM ALL EARTHWORK (CUT & FILL) IN COMPLIANCEWITH ALL LOCAL / STATE CODES AND REQUIREMENTS OFCIVIL DRAWINGS.
16. PERFORM FINAL GRADING TO PROVIDE COMPLETE &POSITIVE DRAINAGE AWAY FROM BUILDING STRUCTUREAND OFF ALL PAVED AREAS AS INDICATED ON GRADINGAND DRAINAGE PLAN. DEMONSTRATE POSITIVEDRAINAGE TO THE SATISFACTION OF THE ARCHITECTAND CIVIL ENGINEER. PONDING OF ANY KIND WILL NOT BEACCEPTABLE.
17. ALL UTILITIES, UTILITY SERVICE LINES AND IRRIGATIONLINES, IF REQUIRED, SHALL BE INSTALLED PRIOR TOPAVING.
18. ALL EXISTING SIGNS, MARKERS DELINEATORS, ETC.,WITHIN THE CONSTRUCTION LIMITS SHALL BEREMOVED, STORED AND GIVEN BACK TO MESD BY THECONTRACTOR UNLESS OTHERWISE NOTED.
19. PROVIDE = FURNISH AND INSTALL.
2428 Baylor Dr SE Albuquerque, NM 87106Tel 505-247-9955 Fax 505-247-1826
Michael Griesel - Vibrantcy1020 Coal SE Albuquerque, NM 87106505-639-4162
G-001 COVER SHEET
10/2
8/20
19 2
:38:
18 P
MC
:\Use
rs\a
naei
ni\D
ocum
ents
\204
12 N
MSU
Gra
nts_
Fide
l_an
aein
i.rvt
NEW MEXICO STATE UNIVERSITY - FIDEL
NMSU FIDEL1500 Third St, Grants, NM 87020-2025
DESIGN DEVELOPMENTIssue Date
G-001
COVERSHEET
ARCHITECTURALA-101 FIRST & SECOND FLOOR EXISTING PLANA-102 FIRST & SECOND FLOOR PLANA-401 ENLARGED PLANSA-411 INTERIOR ELEVATIONSA-601 ROOM FINISH SCHEDULESA-602 DOOR SCHEDULESA-603 WINDOW SCHEDULESA-611 DOOR DETAILSA-612 WINDOW DETIALS
P-001 Plumbing Legends & SpecificationsPD-101 Plumbing Demo- First & Second Floor PlanPD-401 Plumbing Demolition Enlarged PlansP-101 Plumbing New- First & Second Floor PlanP-401 Plumbing New Work Enlarged PlansP-501 Plumbing DiagramsM-001 Legends & SpecificationsMD-101 Mechanical Demo HVAC Floor PlanM-101 Mechanical New HVAC Floor PlanE-001 Electrical Legends & SpecificationsEDL-101 Electrical Demo Lighting Floor PlanEDP-101 Electrical Demo Power Floor PlanEL-101 Electrical New Lighting Floor Plan1 of 1 Electrical Calculation SheetEP-101 Electrical New Power Floor Plan
P001: PLUMBING LEGEND & SPECIFICATIONS PDL101: PLUMBING DEMO WASTE & VENT PLAN PD101: PLUMBING NEW WASTE & VENT PLAN PDP101: PLUMBING DEMO WATER & GAS PLAN PP101: PLUMBING NEW WATER & GAS PLAN P601: PLUMBING SCHEDULES P701: PLUMBING DIAGRAMS FP001: FIRE PROTECTION SPECIFICATIONS
AutoCAD SHX Text
LEGEND
AutoCAD SHX Text
SYMB.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
RISER UP RISER UP RISER DOWN RISER DROP BRANCH- TOP CONNECTION BRANCH- BOTTOM CONNECTION BRANCH- SIDE CONNECTION DIRECTION OF FLOW CAP ON END OF PIPE COLD WATER (CW) HOT WATER (HW) HOT WATER RECIRCULATING (HWR) WASTE (W) VENT-ABOVE (V) VENT-BELOW (V) GAS (G) COMPRESSED AIR (CA) VACUUM (VAC) POINT OF CONNECTION POINT OF DISCONNECT EQUIPMENT DESIGNATION AREA DRAIN BACKFLOW PREVENTOR (REDUCED ZONE) BACKFLOW PREVENTOR (DOUBLE CHECK VALVE ASSEMBLY) BALL VALVE BUTTERFLY VALVE CHECK VALVE CIRCUIT SETTING BALANCING VALVE CLEANOUT (FLOOR) CLEANOUT (WALL) FIXTURE ISOLATION VALVE FLEXIBLE CONNECTION FLOOR DRAIN FLOOR SINK FLOW SWITCH GAS COCK
AutoCAD SHX Text
WH
AutoCAD SHX Text
#
AutoCAD SHX Text
ABBREVIATIONS
AutoCAD SHX Text
ABBR.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
ABOVE FINISHED FLOOR ACCESS DOOR DIAMETER DOWN DRINKING FOUNTAIN EXISTING EXPANSION FEET PER MINUTE FEET PER SECOND GALLONS PER MINUTE HORSEPOWER HERTZ INCHES PER SECOND KILOWATTS LAVATORY
AutoCAD SHX Text
AFF A.D. DIA DN DF (E) EXP FPM FPS GPM HP HZ IPS KW LAV
AutoCAD SHX Text
SYMB.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
GAS METER GAS PRESSURE REGULATOR HOT WATER HEATER HOSE BIBB WITH VACUUM BREAKER GATE VALVE GATE VALVE, ANGLE GAUGE WITH GAUGE COCK/PRESSURE INDICATOR GLOBE VALVE GLOBE VALVE, ANGLE LIFT CHECK VALVE OPEN SITE DRAIN PLUG VALVE PRESSURE GAUGE PRESSURE REDUCING VALVE (PRV) PRESSURE TRANSMITTER OR PRESSURE SWITCH RELIEF/SAFETY VALVE ROOF DRAIN SOLENOID VALVE STRAINER STRAINER WITH BLOW OFF VALVE SWING CHECK VALVE TEMPERATURE GAUGE TEMPERATURE AND PRESSURE RELIEF VALVE TEMPERATURE TRANSMITTER THERMOMETER/TEMPERATURE INDICATOR THREE WAY CONTROL VALVE TWO WAY CONTROL VALVE UNION- SCREWED OR FLANGED VACUUM BREAKER VALVE IN RISE OR DROP WATER HAMMER ARRESTER WATER METER
AutoCAD SHX Text
ABBR.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
LBS MBH (N) N.I.C. NOM OC PH POC TEMP TYP URN V VTR WC
AutoCAD SHX Text
1. GENERAL NOTES GENERAL NOTES A. SUBMISSION OF PROPOSAL DIRECTLY OR INDIRECTLY IN CONNECTION WITH THIS WORK SHALL IMPLY THAT THE BIDDER HAS EXAMINED THE SUBMISSION OF PROPOSAL DIRECTLY OR INDIRECTLY IN CONNECTION WITH THIS WORK SHALL IMPLY THAT THE BIDDER HAS EXAMINED THE JOB SITE UNDER WHICH HE WILL BE OBLIGATED TO OPERATE SHOULD THEY BE AWARDED THE WORK UNDER THIS CONTRACT. NO EXTRA CHARGE WILL BE ALLOWED FOR FAILURE OF ANY BIDDER TO EXAMINE THE SITE PRIOR TO BID. B. CONTRACTOR SHALL VISIT THE SITE AND VERIFY ALL DIMENSIONS IN THE FIELD, AND SHALL ADVISE THE ARCHITECT/ENGINEER OF ANY CONTRACTOR SHALL VISIT THE SITE AND VERIFY ALL DIMENSIONS IN THE FIELD, AND SHALL ADVISE THE ARCHITECT/ENGINEER OF ANY DISCREPANCIES BEFORE PERFORMING THE WORK. C. DO NOT SCALE DRAWINGS. DO NOT SCALE DRAWINGS. D. ALL EQUIPMENT SHALL BE INSTALLED IN STRICT COMPLIANCE WITH MANUFACTURER'S WRITTEN INSTRUCTIONS. THE CONTRACTOR SHALL ALL EQUIPMENT SHALL BE INSTALLED IN STRICT COMPLIANCE WITH MANUFACTURER'S WRITTEN INSTRUCTIONS. THE CONTRACTOR SHALL PROVIDE ALL HANGERS AND SUPPORTS REQUIRED FOR A COMPLETE INSTALLATION. E. CONTRACTOR SHALL COORDINATE ALL WORK WITH THE OWNER AND ALL OTHER CONTRACTORS. CONTRACTOR SHALL COORDINATE ALL WORK WITH THE OWNER AND ALL OTHER CONTRACTORS. F. CONTRACTOR SHALL PROVIDE LABOR TO RECEIVE, UNLOAD, STORE, PROTECT, AND TRANSFER TO POINT OF INSTALLATION, OWNER FURNISHED CONTRACTOR SHALL PROVIDE LABOR TO RECEIVE, UNLOAD, STORE, PROTECT, AND TRANSFER TO POINT OF INSTALLATION, OWNER FURNISHED ITEMS. G. WHERE CONDUIT, CABLES, DUCTWORK, OR PIPING PASSES THROUGH FIRE RATED FLOORS OR WALLS, THE SLEEVES SHALL BE COMPLETELY WHERE CONDUIT, CABLES, DUCTWORK, OR PIPING PASSES THROUGH FIRE RATED FLOORS OR WALLS, THE SLEEVES SHALL BE COMPLETELY SEALED WITH A FIRE STOP MATERIAL BEING SUITABLE FOR THIS SERVICE. THIS MATERIAL SHALL BE INSTALLED IN ACCORDANCE WITH THE REQUIREMENTS OF THE MANUFACTURER TO MAINTAIN THE FIRE RATING OF THE PENETRATED WALL OR FLOOR. H. CONTRACTOR SHALL BE RESPONSIBLE FOR ALL CORING AS IT RELATES TO HIS WORK. CONTRACTOR SHALL BE RESPONSIBLE FOR ALL CORING AS IT RELATES TO HIS WORK. I. CONTRACTOR SHALL BE RESPONSIBLE FOR ALL BEAM PENETRATIONS AS IT RELATES TO HIS WORK. CONTRACTOR SHALL SUBMIT SIZE AND CONTRACTOR SHALL BE RESPONSIBLE FOR ALL BEAM PENETRATIONS AS IT RELATES TO HIS WORK. CONTRACTOR SHALL SUBMIT SIZE AND LOCATION TO THE STRUCTURAL ENGINEER FOR REVIEW AND DETAIL. J. UPON COMPLETION OF CONSTRUCTION, THE CONTRACTOR SHALL SUPPLY THE ENGINEER WITH (1) COMPLETE SET OF FULL SIZE AS-BUILT UPON COMPLETION OF CONSTRUCTION, THE CONTRACTOR SHALL SUPPLY THE ENGINEER WITH (1) COMPLETE SET OF FULL SIZE AS-BUILT DOCUMENTS AND (3) COPIES OF OPERATIONS AND MAINTENANCE MANUALS (SHALL BE OBTAINED AT CONTRACTOR'S EXPENSE). J. INASMUCH AS DESIGN FOR REMODEL AND/OR REHABILITATION REQUIRES THAT CERTAIN ASSUMPTIONS BE MADE REGARDING EXISTING INASMUCH AS DESIGN FOR REMODEL AND/OR REHABILITATION REQUIRES THAT CERTAIN ASSUMPTIONS BE MADE REGARDING EXISTING CONDITIONS, AND BECAUSE SOME OF THESE ASSUMPTIONS CANNOT BE VERIFIED WITHOUT DESTROYING OTHERWISE ADEQUATE OR SERVICEABLE PORTIONS OF THE BUILDING, THE ENGINEER CANNOT ASSURE THE OWNER OR THE CONTRACTOR THAT THE PROFESSIONAL CONSULTING SERVICES HEREIN ENCOMPASS ALL CONTINGENCIES. FIELD COORDINATION DURING CONSTRUCTION IS IMPERATIVE. MAKE REASONABLE ALLOWANCES FOR UNSEEN CONDITIONS. K. REMOVAL AND RELOCATION OF CERTAIN EXISTING WORK WILL BE NECESSARY FOR THE PERFORMANCE OF THE GENERAL WORK. ALL EXISTING REMOVAL AND RELOCATION OF CERTAIN EXISTING WORK WILL BE NECESSARY FOR THE PERFORMANCE OF THE GENERAL WORK. ALL EXISTING CONDITIONS CANNOT BE COMPLETELY DETAILED ON THE DRAWINGS. THE CONTRACTOR SHALL SURVEY THE SITE AND INCLUDED ALL CHANGES IN MAKING UP THE WORK PROPOSAL. L. CONNECT NEW WORK TO EXISTING WORK IN A NEAT AND APPROVED MANNER. CONNECT NEW WORK TO EXISTING WORK IN A NEAT AND APPROVED MANNER. M. DISCONNECT, REMOVE, AND OR RELOCATE EXISTING MATERIAL, EQUIPMENT, AND OTHER WORK AS NOTED OR REQUIRED FOR PROPER DISCONNECT, REMOVE, AND OR RELOCATE EXISTING MATERIAL, EQUIPMENT, AND OTHER WORK AS NOTED OR REQUIRED FOR PROPER INSTALLATION OF NEW SYSTEM. N. ALL EXISTING MATERIAL AND EQUIPMENT REMOVED UNDER THIS CONTRACTOR SHALL BE REMOVED FROM THE SITE OR RETURNED TO THE ALL EXISTING MATERIAL AND EQUIPMENT REMOVED UNDER THIS CONTRACTOR SHALL BE REMOVED FROM THE SITE OR RETURNED TO THE BUILDING OWNER AT THE OWNER'S DISCRETION. 2. SUMMARY AND SCOPE OF WORK: SUMMARY AND SCOPE OF WORK: A. THE DRAWINGS INDICATE DIAGRAMMATICALLY THE EXTENT, GENERAL CHARACTER AND LOCATION OF THE WORK INCLUDED. OFFSETS AND/OR THE DRAWINGS INDICATE DIAGRAMMATICALLY THE EXTENT, GENERAL CHARACTER AND LOCATION OF THE WORK INCLUDED. OFFSETS AND/OR CHANGES IN ELEVATION OF PIPING DUE TO STRUCTURAL OR OTHER INTERFERENCES SHALL BE PROVIDED WITHOUT EXTRA COST. B. CONTRACTOR SHALL VERIFY AND EVALUATE ALL EXISTING CONDITIONS PRIOR TO THE COMMENCEMENT OF WORK. CONTRACTOR SHALL VERIFY AND EVALUATE ALL EXISTING CONDITIONS PRIOR TO THE COMMENCEMENT OF WORK. C. SUBCONTRACTOR SHALL VERIFY EXISTENCE AND LOCATION OF ALL UTILITY SERVICES AND COORDINATE AS REQUIRED BY THEIR RESPECTIVE SUBCONTRACTOR SHALL VERIFY EXISTENCE AND LOCATION OF ALL UTILITY SERVICES AND COORDINATE AS REQUIRED BY THEIR RESPECTIVE AREA OF THE CONSTRUCTION, NOTIFYING THE PRIME CONTRACTOR OF VARIATIONS OR CONFLICTS. D. PROVIDE ALL LABOR, MATERIALS, AND EQUIPMENT NECESSARY FOR THE INSTALLATION OF COMPLETE AND OPERATING SYSTEMS. PROVIDE ALL LABOR, MATERIALS, AND EQUIPMENT NECESSARY FOR THE INSTALLATION OF COMPLETE AND OPERATING SYSTEMS. E. PROVIDE ONE YEAR GUARANTEE AGAINST DEFECTIVE MATERIALS AND WORKMANSHIP AFTER FINAL ACCEPTANCE BY OWNER. PROVIDE ONE YEAR GUARANTEE AGAINST DEFECTIVE MATERIALS AND WORKMANSHIP AFTER FINAL ACCEPTANCE BY OWNER. F. ENTIRE DEMOLITION AND NEW WORK INSTALLATION SHALL CONFORM TO ALL APPLICABLE LAWS, CODES, AND REGULATIONS OF MUNICIPAL, ENTIRE DEMOLITION AND NEW WORK INSTALLATION SHALL CONFORM TO ALL APPLICABLE LAWS, CODES, AND REGULATIONS OF MUNICIPAL, STATE AND FEDERAL AUTHORITIES. G. SHOP DRAWINGS: SUBMIT MATERIAL LIST AND SHOP DRAWINGS FOR MAJOR EQUIPMENT AND MATERIALS TO THE ARCHITECT/ENGINEER FOR SHOP DRAWINGS: SUBMIT MATERIAL LIST AND SHOP DRAWINGS FOR MAJOR EQUIPMENT AND MATERIALS TO THE ARCHITECT/ENGINEER FOR APPROVAL. H. IF NOT SPECIFICALLY DEFINED IN THESE CONSTRUCTION DOCUMENTS, MATERIALS AND/OR EQUIPMENT SHALL BE IDENTIFIED BY THE IF NOT SPECIFICALLY DEFINED IN THESE CONSTRUCTION DOCUMENTS, MATERIALS AND/OR EQUIPMENT SHALL BE IDENTIFIED BY THE SUBCONTRACTOR WITH SUFFICIENT TIME TO ALLOW SELECTION, PURCHASE, AND DELIVERY TO MAINTAIN CONSTRUCTION SCHEDULE. I. THE MANUFACTURER OF EQUIPMENT OR MATERIALS FIRST NAMED ON THE DRAWINGS IS THE BASIS OF DESIGN. OTHER MANUFACTURERS, IF THE MANUFACTURER OF EQUIPMENT OR MATERIALS FIRST NAMED ON THE DRAWINGS IS THE BASIS OF DESIGN. OTHER MANUFACTURERS, IF LISTED, ARE CONSIDERED GENERAL EQUIVALENTS ONLY. WHERE CONTRACT DOCUMENTS PERMIT SELECTION OF EQUIVALENTS, OR WHERE SUBSTITUTIONS ARE AUTHORIZED, COORDINATE CLEARANCE AND OTHER INTERFACE REQUIREMENTS WITH MECHANICAL AND OTHER WORK. i. PROVIDED NECESSARY ADDITIONAL ITEMS SO THAT SELECTED OR SUBSTITUTED ITEM OPERATES EQUIVALENT TO THE BASIS OF DESIGN PROVIDED NECESSARY ADDITIONAL ITEMS SO THAT SELECTED OR SUBSTITUTED ITEM OPERATES EQUIVALENT TO THE BASIS OF DESIGN AND PROPERLY FITS IN THE AVAILABLE SPACE ALLOCATED FOR THE BASIS OF DESIGN. ii. PROVIDED ALL FEATURES WHICH ARE STANDARD ON THE BASIS OF DESIGN PLUS ANY SPECIFIED OPTIONS. PROVIDED ALL FEATURES WHICH ARE STANDARD ON THE BASIS OF DESIGN PLUS ANY SPECIFIED OPTIONS. iii. BE RESPONSIBLE FOR ASSURING THAT PIPING, CONDUIT, DUCT, FLUE, AND OTHER SERVICE LOCATIONS FOR GENERAL EQUIVALENTS OR BE RESPONSIBLE FOR ASSURING THAT PIPING, CONDUIT, DUCT, FLUE, AND OTHER SERVICE LOCATIONS FOR GENERAL EQUIVALENTS OR SUBSTITUTIONS DO NOT CAUSE ACCESS, SERVICE, OR OPERATIONAL DIFFICULTIES ANY GREATER THAN WOULD BE ENCOUNTERED WITH THE BASE DESIGN. J. THE CONTRACTOR SHALL SECURE ALL PERMITS OR APPLICATIONS AND PAY ANY AND ALL FEES. THE CONTRACTOR SHALL SECURE ALL PERMITS OR APPLICATIONS AND PAY ANY AND ALL FEES. K. PLUMBING DEMOLITION AS INDICATED ON DRAWINGS. PLUMBING DEMOLITION AS INDICATED ON DRAWINGS. L. ALL DUCTWORK, DIFFUSERS, PIPING, FIXTURES, AND EQUIPMENT SHOWN IN LIGHT LINE WEIGHT IS EXISTING. NEW INDICATED BY HEAVIER ALL DUCTWORK, DIFFUSERS, PIPING, FIXTURES, AND EQUIPMENT SHOWN IN LIGHT LINE WEIGHT IS EXISTING. NEW INDICATED BY HEAVIER LINE WEIGHT, EXCEPT WHERE NOTED. M. PROVIDE ALL NECESSARY TEMPORARY OR PERMANENT CAPS OR PLUGS FOR PIPING. DO NOT LEAVE PIPING OPEN ENDED. PROVIDE ALL NECESSARY TEMPORARY OR PERMANENT CAPS OR PLUGS FOR PIPING. DO NOT LEAVE PIPING OPEN ENDED. N. WHERE USED, THE TERM “PROVIDE” SHALL MEAN “FURNISH AND INSTALL”. WHERE USED, THE TERM “PROVIDE” SHALL MEAN “FURNISH AND INSTALL”. PROVIDE” SHALL MEAN “FURNISH AND INSTALL”. SHALL MEAN “FURNISH AND INSTALL”. FURNISH AND INSTALL”. . O. INSTALL ALL SHOCK ABSORBERS IN ACCORDANCE WITH THE LATEST “PLUMBING AND DRAINAGE INSTITUTE STANDARDS” FOR WATER HAMMER INSTALL ALL SHOCK ABSORBERS IN ACCORDANCE WITH THE LATEST “PLUMBING AND DRAINAGE INSTITUTE STANDARDS” FOR WATER HAMMER PLUMBING AND DRAINAGE INSTITUTE STANDARDS” FOR WATER HAMMER FOR WATER HAMMER ARRESTORS. P. LOCATE ACCESS PANELS IN NON ACCESSIBLE CEILINGS AND WALLS FOR ALL VALVES, SHOCK ABSORBERS, CLEANOUTS AND ALL OTHER ITEMS LOCATE ACCESS PANELS IN NON ACCESSIBLE CEILINGS AND WALLS FOR ALL VALVES, SHOCK ABSORBERS, CLEANOUTS AND ALL OTHER ITEMS THAT REQUIRE ACCESS TO PROPERLY MAINTAIN OR SERVICE THE BUILDING. Q. PROVIDE CLEANOUTS AS REQUIRED BY CODE. PROVIDE CLEANOUTS AS REQUIRED BY CODE. R. INSTALL WORK SO AS TO BE READILY ACCESSIBLE FOR OPERATION, MAINTENANCE, AND REPAIR. MINOR DEVIATIONS FROM DRAWINGS MAY BE INSTALL WORK SO AS TO BE READILY ACCESSIBLE FOR OPERATION, MAINTENANCE, AND REPAIR. MINOR DEVIATIONS FROM DRAWINGS MAY BE MADE TO ACCOMPLISH THIS, BUT CHANGES WHICH INVOLVE EXTRA COST SHALL NOT BE MADE WITHOUT PRIOR APPROVAL. S. ALL VENT THRU ROOF (VTR) ROOF PENETRATIONS INDICATED ON PLANS ARE PRELIMINARY. FINAL LOCATIONS SHALL BE COORDINATED WITH ALL VENT THRU ROOF (VTR) ROOF PENETRATIONS INDICATED ON PLANS ARE PRELIMINARY. FINAL LOCATIONS SHALL BE COORDINATED WITH ALL TRADES. ALL VTR'S SHALL BE A MINIMUM OF 10'-0” FROM ALL FRESH AIR INTAKE OPENINGS. FROM ALL FRESH AIR INTAKE OPENINGS. 3. PLUMBING EQUIPMENT AND PIPING IDENTIFICATION PLUMBING EQUIPMENT AND PIPING IDENTIFICATION A. PROVIDE IDENTIFICATION OF ALL EQUIPMENT, PIPES, AND VALVES. PROVIDE IDENTIFICATION OF ALL EQUIPMENT, PIPES, AND VALVES. B. IDENTIFICATION DEVICES TO BE USED SHALL INCLUDE THE FOLLOWING: IDENTIFICATION DEVICES TO BE USED SHALL INCLUDE THE FOLLOWING: i. PLASTIC PIPE MARKERS PLASTIC PIPE MARKERS ii. VALVE TAGS AND EQUIPMENT TAGS VALVE TAGS AND EQUIPMENT TAGS 4. INSULATION INSULATION A. ALL HOT WATER PIPING TO BE INSULATED WITH 1” FIBERGLASS INSULATION. ALL COLD WATER PIPING TO BE INSULATED WITH ½” FOAM ALL HOT WATER PIPING TO BE INSULATED WITH 1” FIBERGLASS INSULATION. ALL COLD WATER PIPING TO BE INSULATED WITH ½” FOAM FIBERGLASS INSULATION. ALL COLD WATER PIPING TO BE INSULATED WITH ½” FOAM FOAM INSULATION. B. FIRE RETARDANT JACKET ON PIPE INSULATION. FIRE RETARDANT JACKET ON PIPE INSULATION. C. VALVES AND FITTINGS: PREMOLDED FIBERGLASS FITTINGS OR RADIAL MITERED SEGMENTS OF PIPE INSULATION, INSULATING CEMENT, VALVES AND FITTINGS: PREMOLDED FIBERGLASS FITTINGS OR RADIAL MITERED SEGMENTS OF PIPE INSULATION, INSULATING CEMENT, FIBERGLASS REINFORCING CLOTH, AND MASTIC, VAPOR SEAL INSULATION ON CW PIPING. 5. SUPPORTS AND HANGERS SUPPORTS AND HANGERS A. ALL PIPE SHALL BE SUPPORTED FROM THE BUILDING STRUCTURE PER NFPA AND SMACNA, AND IN A NEAT AND WORKMANLIKE MANNER. ALL PIPE SHALL BE SUPPORTED FROM THE BUILDING STRUCTURE PER NFPA AND SMACNA, AND IN A NEAT AND WORKMANLIKE MANNER. THE USE OF WIRE AND PREFORMED METAL TO SUPPORT PIPES WILL NOT BE PERMITTED. SPACING OF PIPE SUPPORTS SHALL BE IN ACCORDANCE WITH PLUMBING CODE. B. SUPPORT NEW PIPING FROM BUILDING STRUCTURE AND OR FRAMING IN AN APPROVED MANNER. WHERE OVERHEAD CONSTRUCTION DOES NOT SUPPORT NEW PIPING FROM BUILDING STRUCTURE AND OR FRAMING IN AN APPROVED MANNER. WHERE OVERHEAD CONSTRUCTION DOES NOT PERMIT FASTENING OF SUPPORTS FOR EQUIPMENT, FURNISH ADDITIONAL FRAMING. 6. DOMESTIC WATER SUPPLY PIPING DOMESTIC WATER SUPPLY PIPING A. PROVIDE PEX TUBING FOR ALL BUILDING WATER SUPPLY AND DISTRIBUTION PIPING. MATERIAL AND FITTINGS SHALL BE IN ACCORDANCE WITH PROVIDE PEX TUBING FOR ALL BUILDING WATER SUPPLY AND DISTRIBUTION PIPING. MATERIAL AND FITTINGS SHALL BE IN ACCORDANCE WITH ALL APPLICABLE ASTM REFERENCE STANDS AS REQUIRED BY CODE. PEX SHALL NOT BE USED WITHIN 18 INCHES OF CONNECTION TO WATER HEATER. NOTE THAT ALL DOMESTIC WATER PIPING SHALL BE INSULATED IN ACCORDANCE WITH ABOVE SECTIONS B. VALVES: COLD AND HOT WATER, FULL PORT BALL VALVES, 2 INCHES AND SMALLER, 600 PSI WOG, SERVICEABLE IN LINE. VALVES: COLD AND HOT WATER, FULL PORT BALL VALVES, 2 INCHES AND SMALLER, 600 PSI WOG, SERVICEABLE IN LINE. 7. SANITARY DRAINAGE AND VENT PIPING SANITARY DRAINAGE AND VENT PIPING A. ABOVE GRADE: ABOVE GRADE: i. SCHEDULE 40 PVC SHALL BE ACCEPTABLE WHERE ALLOWED BY CODE, EXCEPT WHERE OTHERWISE NOTED. INDIRECT WASTED PIPE AT SCHEDULE 40 PVC SHALL BE ACCEPTABLE WHERE ALLOWED BY CODE, EXCEPT WHERE OTHERWISE NOTED. INDIRECT WASTED PIPE AT 3-COMPARTMENT SINK SHALL BE GALVANIZED METAL PIPE OR CHROME FINISHED PIPE FOR APPEARANCE. ii. DRAINAGE PIPING SHALL RUN AS STRAIGHT AS POSSIBLE AND SHALL HAVE LONG TURN FITTINGS DRAINAGE PIPING SHALL RUN AS STRAIGHT AS POSSIBLE AND SHALL HAVE LONG TURN FITTINGS iii. ALL VENT PIPING SHALL BE SLOPED TO DRAIN BACK TO FIXTURES. ALL VENT PIPING SHALL BE SLOPED TO DRAIN BACK TO FIXTURES. iv. CONTRACTOR IS RESPONSIBLE FOR PROPER FLASHING OF THE VENT PIPING RUN THROUGH THE ROOF OR WALL. CONTRACTOR IS RESPONSIBLE FOR PROPER FLASHING OF THE VENT PIPING RUN THROUGH THE ROOF OR WALL. 8. TESTING TESTING A. PLUMBING SYSTEMS SHALL BE FLOW AND PRESSURE TESTED IN ACCORDANCE WITH STANDARD PRACTICE AND PLUMBING CODE.PLUMBING SYSTEMS SHALL BE FLOW AND PRESSURE TESTED IN ACCORDANCE WITH STANDARD PRACTICE AND PLUMBING CODE.
AutoCAD SHX Text
PLUMBING SPECIFICATIONS
AutoCAD SHX Text
TP
AutoCAD SHX Text
S
AutoCAD SHX Text
CBV
AutoCAD SHX Text
SA
AutoCAD SHX Text
PI/GA
AutoCAD SHX Text
TH/TI
AutoCAD SHX Text
PT/PS
AutoCAD SHX Text
TT
AutoCAD SHX Text
FS
AutoCAD SHX Text
ADR
AutoCAD SHX Text
OS
AutoCAD SHX Text
FD
AutoCAD SHX Text
WH
AutoCAD SHX Text
WM
AutoCAD SHX Text
GM
AutoCAD SHX Text
CO
AutoCAD SHX Text
CO
AutoCAD SHX Text
FS
AutoCAD SHX Text
HB
AutoCAD SHX Text
RD
AutoCAD SHX Text
POUNDS THOUSAND BTU'S PER HOUR NEW NOT IN CONTRACT NOMINAL ON CENTER PHASE POINT OF CONNECTION TEMPERATURE TYPICAL URINAL VOLTAGE VENT THROUGH ROOF WATER CLOSET
1. REPLACE FAUCET ON EXISTING MOP SINK; SEE NEW WORK PLAN.2. REPLACE DRINKING WATER FOUNTAIN; SEE NEW WORK PLAN.3. REMOVE EXISTING WATER VALVES\DRAINS FEEDING ROOFTOP EVAPORATIVE
COOLER.4. REMOVE EXISTING GAS FIRED WATER HEATER FROM SECOND FLOOR CLOSET.
SEE NEW WATER HEATER LOCATION ON FIRST FLOOR.5. WATER SERVICE BACKFLOW PREVENTER TO REMAIN IN CLOSET.
1. DISCONNECT AND REMOVE EXISTING FIXTURE TO BE REPLACED IN SAMELOCATION AND FACILITATE FOR ROOM RENOVATION.
2. DISCONNECT AND REMOVE EXISTING FIXTURE THAT WILL BE REPLACED IN ANEW CONFIGURATION. REMOVAL TO INCLUDE PIPING INWALL\CHASE\FLOOR FOR COMPLETE REMOVAL AND FACILITATE FOR ROOMRENOVATION.
3. COMPLETELY DISCONNECT AND REMOVE EXISTING FIXTURE THAT WILL NOTBE REPLACED. REMOVAL TO INCLUDE PIPING IN WALL\CHASE\FLOOR FORCOMPLETE REMOVAL AND FACILITATE FOR ROOM RENOVATION.
4. REPLACE EXISTING FLOOR DRAIN COVER AFTER FLOOR REPLACEMENT ISCOMPLETED. SEE NEW WORK PLAN
5. DISCONNECT AND REMOVE EXISTING SHOWER HEAD, AND SHOWER VALVETO BE REPLACED IN SAME LOCATION AND FACILITATE FOR ROOMRENOVATION.
6. REMOVE EXISTING SHOWER DRAINS LOCATED IN PERIMETER TRENCH.COORDINATE WITH ARCHITECTURAL WORK AND REMOVAL OF CONCRETEFLOOR.
1. INSTALL NEW FIXTURE IN THE SAME LOCATION AS REMOVED FIXTURE.PROVIDE PIPE EXTENSION, FITTINGS, ADAPTERS AS NEEDED TOACCOMMODATE NEW FIXTURE WITH NEW FINISHES.
2. CONNECT NEW FIXTURE\REPLACEMENT FIXTURE TO EXISTING PIPING.EXTEND EXISTING PIPING AS NEEDED. PROVIDE PIPE EXTENSION, FITTINGS,ADAPTERS AS NEEDED TO ACCOMMODATE NEW FIXTURE WITH NEWFINISHES.
3. NEW ADA SHOWER HEAD AND CONTROL TO REPLACE EXISTING. INSTALLWAND, HOSE AND VERTICAL MOUNTING BAR. SEE ARCHITECTURAL DETAILS.
4. REPLACE EXISTING FLOOR DRAIN COVER AFTER FLOOR REPLACEMENT ISCOMPLETED. CLEAN AND POLISH RIM AND ALL EXPOSED BODY AND INTERNALDRAIN BODY. PROVIDE RUBBER TRAP SEAL. COORDINATE WORK TO ADAPTAND MATCH TO EXISTING DRAIN AND NEW FINISHES.
5. NEW SHOWER HEAD AND CONTROL TO REPLACE EXISTING.6. NEW 48” TRENCH DRAIN TO SERVE SHOWER. COORDINATE WITH NEW
CONCRETE FLOOR REPLACEMENT.7. PROVIDE NEW HOSE-BIB CONNECTION FOR FLOOR PRESSURE WASHER.
INSTALL HB 42” AFF, COORDINATE LOCATION WITH WNMU. CONCEAL NEWPIPING IN WALL AND IN NEW PRESSURE WASHER CLOSET.
M-001: MECHANICAL LEGEND & SPECIFICATIONS MD-101: MECHANICAL HVAC PLAN M-101: MECHANICAL ROOF PLAN M601: MECHANICAL SCHEDULES M701: MECHANICAL DIAGRAMS
AutoCAD SHX Text
LEGEND
AutoCAD SHX Text
SYMB.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
ABBREVIATIONS
AutoCAD SHX Text
ABBR.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
ABOVE FINISHED FLOOR DIAMETER EXISTING ENTERING AIR TEMPERATURE EXPANSION FEET PER MINUTE FEET PER SECOND HORSEPOWER HERTZ INCHES PER SECOND KILOWATTS LEAVING AIR TEMPERATURE POUNDS LEAVING WATER TEMPERATURE THOUSAND BTU'S PER HOUR NEW NOT IN CONTRACT
AutoCAD SHX Text
AFF DIA (E) EAT EXP FPM FPS HP HZ IPS KW LAT LBS LWT MBH (N) N.I.C.
AutoCAD SHX Text
SYMB.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
ABBR.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
NOMINAL OUTSIDE AIR OUTSIDE AIR TEMPERATURE ON CENTER PHASE POINT OF CONNECTION PRESSURE RETURN AIR RELATIVE HUMIDITY SUPPLY AIR SUPPLY AIR TEMPERATURE SENSIBLE COOLING CAPACITY STATIC PRESSURE TEMPERATURE REFRIGERATION CAPACITY (1 TON=12,000 BTUH) TOTAL STATIC PRESSURE TYPICAL VOLTAGE VENT THROUGH ROOF
AutoCAD SHX Text
NOM OA OAT OC PH POC PRESS RA RH SA SAT SENS SP TEMP TON TSP TYP V VTR
AutoCAD SHX Text
POINT OF CONNECTION POINT OF DISCONNECT THERMOSTAT SQUARE SUPPLY DIFFUSER ROUND SUPPLY DIFFUSER RETURN GRILLE EXHAUST GRILLE SIDEWALL SUPPLY SIDEWALL RETURN SIDEWALL EXHAUST SUPPLY AIR ARROW RETURN AIR ARROW EXHAUST AIR ARROW DUCTWORK- DEMO DUCTWORK- EXISTING DUCTWORK- NEW DUCTWORK- ROUND DUCTWORK- RIGID DUCT TRANSITION DUCT SQUARE TO ROUND TRANSITION METERED ELBOW
AutoCAD SHX Text
T
AutoCAD SHX Text
RTU
AutoCAD SHX Text
#
AutoCAD SHX Text
S1
AutoCAD SHX Text
100cfm
AutoCAD SHX Text
8"%%c
AutoCAD SHX Text
BALANCING DAMPER FIRE DAMPER SMOKE DAMPER SUPPLY AIR DUCT UP SUPPLY AIR DUCT DOWN RETURN/EXHAUST DUCT UP RETURN/EXHAUST DUCT DOWN DUCTWORK DIMENSIONS (WxH) DUCTWORK DIMENSIONS (DIA.) EQUIPMENT DESIGNATION DIFFUSER/GRILLE DESIGNATION RISER UP RISER UP RISER DOWN RISER DROP BRANCH- TOP CONNECTION BRANCH- BOTTOM CONNECTION BRANCH- SIDE CONNECTION CAP ON END OF PIPE GAS- LOW PRESSURE
AutoCAD SHX Text
8"%%C
AutoCAD SHX Text
8"x10"
AutoCAD SHX Text
8"x10"
AutoCAD SHX Text
8"%%C
AutoCAD SHX Text
BD
AutoCAD SHX Text
1. GENERAL GENERAL 1.1. COMPLY WITH DIVISION 1. COMPLY WITH DIVISION 1. 1.2. SUBMISSION OF PROPOSAL SHALL IMPLY THAT THE BIDDER HAS EXAMINED THE JOB SITE. NO EXTRA CHARGE WILL BE ALLOWED FOR FAILURE OF SUBMISSION OF PROPOSAL SHALL IMPLY THAT THE BIDDER HAS EXAMINED THE JOB SITE. NO EXTRA CHARGE WILL BE ALLOWED FOR FAILURE OF ANY BIDDER TO EXAMINE THE SITE PRIOR TO BID. 1.3. THE ARCHITECT/ENGINEER SHALL DETERMINE THE INTENT OF THE DRAWINGS. THE ARCHITECT/ENGINEER SHALL DETERMINE THE INTENT OF THE DRAWINGS. 1.4. THE DRAWINGS INDICATE DIAGRAMMATICALLY THE EXTENT, GENERAL CHARACTER AND LOCATION OF THE WORK INCLUDED. PROVIDE OFFSETS AND/OR THE DRAWINGS INDICATE DIAGRAMMATICALLY THE EXTENT, GENERAL CHARACTER AND LOCATION OF THE WORK INCLUDED. PROVIDE OFFSETS AND/OR CHANGES IN ELEVATION OF PIPING AND DUCTWORK AS NEEDED DUE TO STRUCTURAL OR OTHER INTERFERENCES. 1.5. PRIOR TO COMMENCING WORK, VISIT THE SITE AND VERIFY DIMENSIONS IN THE FIELD. ADVISE THE ARCHITECT/ENGINEER OF ANY DISCREPANCIES PRIOR TO COMMENCING WORK, VISIT THE SITE AND VERIFY DIMENSIONS IN THE FIELD. ADVISE THE ARCHITECT/ENGINEER OF ANY DISCREPANCIES BEFORE COMMENCING WORK. 1.6. INSTALL EQUIPMENT TO COMPLY WITH MANUFACTURER'S WRITTEN INSTRUCTIONS. PROVIDE ACCESSORIES NEEDED FOR A COMPLETE INSTALLATION. INSTALL EQUIPMENT TO COMPLY WITH MANUFACTURER'S WRITTEN INSTRUCTIONS. PROVIDE ACCESSORIES NEEDED FOR A COMPLETE INSTALLATION. 1.7. COORDINATE WORK WITH THE OWNER AND OTHER CONTRACTORS. COORDINATE WORK WITH THE OWNER AND OTHER CONTRACTORS. 1.8. COORDINATE AND SCHEDULE WITH THE OWNER WORK THAT INVOLVES SHUTDOWN AND/OR INTERRUPTION OF EXISTING SYSTEMS /SERVICES. COORDINATE AND SCHEDULE WITH THE OWNER WORK THAT INVOLVES SHUTDOWN AND/OR INTERRUPTION OF EXISTING SYSTEMS /SERVICES. 1.9. PROVIDE LABOR TO RECEIVE, UNLOAD, STORE, PROTECT, AND TRANSFER TO POINT OF INSTALLATION, OWNER FURNISHED ITEMS. PROVIDE LABOR TO RECEIVE, UNLOAD, STORE, PROTECT, AND TRANSFER TO POINT OF INSTALLATION, OWNER FURNISHED ITEMS. 1.10. EQUIPMENT AND MATERIALS SHALL BE NEW UNLESS INDICATED OTHERWISE. EQUIPMENT AND MATERIALS SHALL BE NEW UNLESS INDICATED OTHERWISE. 1.11. CUTTING AND PATCHING: CUTTING AND PATCHING: 1.11.1. PROVIDE CUTTING AND PATCHING. PROVIDE CUTTING AND PATCHING. 1.11.2. PATCHING WORK SHALL BE PERFORMED BY THE APPROPRIATE TRADES. PATCHING WORK SHALL BE PERFORMED BY THE APPROPRIATE TRADES. 1.11.3. COORDINATE WITH OTHER TRADES. COORDINATE WITH OTHER TRADES. 1.11.4. PERFORM IT NEATLY AND TO MINIMIZE DAMAGE. PERFORM IT NEATLY AND TO MINIMIZE DAMAGE. 1.11.5. PATCH CUTS TO RETURN THE SURFACE TO ITS ORIGINAL CONDITION. MATCH ADJACENT SURFACES. PATCH CUTS TO RETURN THE SURFACE TO ITS ORIGINAL CONDITION. MATCH ADJACENT SURFACES. 2. SUMMARY AND SCOPE OF WORK SUMMARY AND SCOPE OF WORK 2.1. VERIFY AND EVALUATE EXISTING CONDITIONS PRIOR TO THE COMMENCEMENT OF WORK. PROVIDE A WRITTEN LIST OF ANY ITEMS THAT NEED REPAIR VERIFY AND EVALUATE EXISTING CONDITIONS PRIOR TO THE COMMENCEMENT OF WORK. PROVIDE A WRITTEN LIST OF ANY ITEMS THAT NEED REPAIR TO THE OWNER PRIOR TO COMMENCING WORK AND REQUEST DIRECTION ON HOW TO PROCEED. 2.2. PROVIDE LABOR, MATERIALS, AND EQUIPMENT NECESSARY FOR THE INSTALLATION OF COMPLETE AND OPERATING SYSTEMS. PROVIDE LABOR, MATERIALS, AND EQUIPMENT NECESSARY FOR THE INSTALLATION OF COMPLETE AND OPERATING SYSTEMS. 2.3. PROVIDE ONE YEAR GUARANTEE AGAINST DEFECTIVE MATERIALS AND WORKMANSHIP AFTER FINAL ACCEPTANCE BY OWNER. PROVIDE ONE YEAR GUARANTEE AGAINST DEFECTIVE MATERIALS AND WORKMANSHIP AFTER FINAL ACCEPTANCE BY OWNER. 2.4. DEMOLITION AND NEW WORK SHALL CONFORM TO APPLICABLE LAWS, CODES, AND REGULATIONS OF MUNICIPAL, STATE, AND FEDERAL AUTHORITIES. DEMOLITION AND NEW WORK SHALL CONFORM TO APPLICABLE LAWS, CODES, AND REGULATIONS OF MUNICIPAL, STATE, AND FEDERAL AUTHORITIES. 2.5. SHOP DRAWINGS: SUBMIT MATERIAL LIST AND SHOP DRAWINGS FOR MAJOR EQUIPMENT TO THE ARCHITECT/ENGINEER FOR REVIEW. SUBMIT THE SHOP DRAWINGS: SUBMIT MATERIAL LIST AND SHOP DRAWINGS FOR MAJOR EQUIPMENT TO THE ARCHITECT/ENGINEER FOR REVIEW. SUBMIT THE FOLLOWING: 2.5.1. DIFFUSERS AND GRILLES DIFFUSERS AND GRILLES 2.5.2. DUCTWORK AND ACCESSORIES DUCTWORK AND ACCESSORIES 2.5.3. INSULATION INSULATION 2.5.4. AUTOMATIC TEMPERATURE CONTROLS. AUTOMATIC TEMPERATURE CONTROLS. 2.6. THE CONTRACTOR SHALL SECURE ALL PERMITS OR APPLICATIONS AND PAY ANY AND ALL FEES. THE CONTRACTOR SHALL SECURE ALL PERMITS OR APPLICATIONS AND PAY ANY AND ALL FEES. 2.7. PROVIDE DEMOLITION AS INDICATED ON DRAWINGS. PROVIDE DEMOLITION AS INDICATED ON DRAWINGS. 2.8. PROTECT MATERIALS AND EQUIPMENTS FROM MOISTURE, DUST, DIRT AND DAMAGE UNTIL ACCEPTANCE. PROTECT MATERIALS AND EQUIPMENTS FROM MOISTURE, DUST, DIRT AND DAMAGE UNTIL ACCEPTANCE. 2.9. WHERE CONDUITS, CABLES, DUCTWORK, OR PIPING PASSES THROUGH FIRE RATED FLOORS OR WALLS, THE SLEEVES SHALL BE COMPLETELY SEALED WHERE CONDUITS, CABLES, DUCTWORK, OR PIPING PASSES THROUGH FIRE RATED FLOORS OR WALLS, THE SLEEVES SHALL BE COMPLETELY SEALED WITH AN APPROPRIATE FIRE STOP MATERIAL SUITABLE FOR THIS SERVICE. THIS MATERIAL SHALL BE INSTALLED IN ACCORDANCE WITH THE REQUIREMENTS OF THE MANUFACTURER TO MAINTAIN THE FIRE RATING OF THE PENETRATED WALL OR FLOOR. 2.10. CONTRACTOR SHALL BE RESPONSIBLE FOR CORING REQUIRED TO ACCOMPLISH WORK. CONTRACTOR SHALL BE RESPONSIBLE FOR CORING REQUIRED TO ACCOMPLISH WORK. 2.11. UPON COMPLETION OF CONSTRUCTION, PROVIDE TO THE OWNER: UPON COMPLETION OF CONSTRUCTION, PROVIDE TO THE OWNER: 2.11.1. (1) COMPLETE SET OF FULL SIZE AS-BUILT DOCUMENTS (1) COMPLETE SET OF FULL SIZE AS-BUILT DOCUMENTS 2.11.2. (3) COPIES OF OPERATIONS AND MAINTENANCE MANUALS. (3) COPIES OF OPERATIONS AND MAINTENANCE MANUALS. 3. TESTING AND BALANCING TESTING AND BALANCING 3.1. PROVIDE TESTING AND BALANCING (TAB) SERVICES. PROVIDE TESTING AND BALANCING (TAB) SERVICES. 3.2. COST OF TESTING AND BALANCING (TAB) SHALL BE BY THIS (MECHANICAL) CONTRACTOR. COST OF TESTING AND BALANCING (TAB) SHALL BE BY THIS (MECHANICAL) CONTRACTOR. 3.3. CONTRACTOR THAT PERFORMS THE TAB WORK SHALL BE NEBB CERTIFIED, OR EQUAL. CONTRACTOR THAT PERFORMS THE TAB WORK SHALL BE NEBB CERTIFIED, OR EQUAL. 3.4. TAB WORK SHALL COMPLY WITH NEBB STANDARDS FOR TESTING, ADJUSTING, AND BALANCING OF ENVIRONMENTAL SYSTEMS. TAB WORK SHALL COMPLY WITH NEBB STANDARDS FOR TESTING, ADJUSTING, AND BALANCING OF ENVIRONMENTAL SYSTEMS. 3.5. AFTER SYSTEM MODIFICATIONS ARE COMPLETE, BALANCE AIR QUANTITIES FOR ENTIRE RTU-1 AND RTU-4 SYSTEMS. BALANCE TO THE CFM AFTER SYSTEM MODIFICATIONS ARE COMPLETE, BALANCE AIR QUANTITIES FOR ENTIRE RTU-1 AND RTU-4 SYSTEMS. BALANCE TO THE CFM QUANTITIES INDICATED ON THE DRAWINGS. USE EXISTING BALANCE DAMPERS FOR ANY REQUIRED TRIM ADJUSTMENTS. 3.6. BALANCE DIFFUSERS AND GRILLES TO WITHIN +5% TO -5%. BALANCE DIFFUSERS AND GRILLES TO WITHIN +5% TO -5%. 3.7. PROVIDE FINAL REPORT WITH CERTIFICATION SHEETS. CONTENT AND FORMAT ACCORDING TO NEBB STANDARD FORMS. PROVIDE FINAL REPORT WITH CERTIFICATION SHEETS. CONTENT AND FORMAT ACCORDING TO NEBB STANDARD FORMS. 4. AIR DISTRIBUTION SYSTEMS AIR DISTRIBUTION SYSTEMS 4.1. AIR TERMINALS AIR TERMINALS 4.1.1. FINISH OF DIFFUSERS AND GRILLES SHALL BE STANDARD WHITE COLOR. NECK SIZE SHALL BE AS INDICATED ON DRAWINGS. DIFFUSERS SHALL FINISH OF DIFFUSERS AND GRILLES SHALL BE STANDARD WHITE COLOR. NECK SIZE SHALL BE AS INDICATED ON DRAWINGS. DIFFUSERS SHALL FIT CEILING GRID. SILICONE SEAL AIR TIGHT TO CEILING. 4.1.2. SPRAY PAINT INSIDE OF DUCT FLAT BLACK, BEHIND ALL GRILLES. SPRAY PAINT INSIDE OF DUCT FLAT BLACK, BEHIND ALL GRILLES. 4.2. SHEET METAL WORK AND DUCTWORK SHEET METAL WORK AND DUCTWORK 4.2.1. DUCTWORK SHALL BE GALVANIZED SHEET STEEL AND SHALL BE INSTALLED IN ACCORDANCE WITH SHEET METAL AND AIR CONDITIONING DUCTWORK SHALL BE GALVANIZED SHEET STEEL AND SHALL BE INSTALLED IN ACCORDANCE WITH SHEET METAL AND AIR CONDITIONING CONTRACTORS NATIONAL ASSOCIATION, INC. (SMACNA) DUCT CONSTRUCTION STANDARDS. DUCT SYSTEMS TO BE LOW VELOCITY TYPE, WITH A PRESSURE CLASSIFICATION OF 2”. . 4.2.2. ALL DUCT DIMENSIONS INDICATED ON THE PLANS ARE INSIDE CLEAR DIMENSIONS. DIMENSIONS MAY BE CHANGED SO LONG AS THE NET FREE ALL DUCT DIMENSIONS INDICATED ON THE PLANS ARE INSIDE CLEAR DIMENSIONS. DIMENSIONS MAY BE CHANGED SO LONG AS THE NET FREE FACE AREA IS MAINTAINED. 4.2.3. SUPPLY DUCTWORK TO BE RECTANGULAR WITH HEMMED “S” LONGITUDINAL SEAMS AND DUCTMATE TRANSVERSE JOINTS. SUPPLY DUCTWORK TO BE RECTANGULAR WITH HEMMED “S” LONGITUDINAL SEAMS AND DUCTMATE TRANSVERSE JOINTS. S” LONGITUDINAL SEAMS AND DUCTMATE TRANSVERSE JOINTS. LONGITUDINAL SEAMS AND DUCTMATE TRANSVERSE JOINTS. 4.2.4. DUCTWORK ELBOWS TO BE LONG RADIUS TYPE. DUCTWORK ELBOWS TO BE LONG RADIUS TYPE. 4.2.5. ALL BRANCH DUCTS SHALL HAVE MANUAL VOLUME DAMPERS: GALVANIZED STEEL PER SMACNA EXCEPT PROVIDE BEARING AT ONE END OF ALL BRANCH DUCTS SHALL HAVE MANUAL VOLUME DAMPERS: GALVANIZED STEEL PER SMACNA EXCEPT PROVIDE BEARING AT ONE END OF DAMPER ROD AND QUADRANT, WITH LEVER AND LOCKSCREW AT THE OPPOSITE END. FOR INSULATED DUCTS, QUADRANTS MOUNTED ON COLLAR TO CLEAR INSULATION. LEVERS MUST BE ACCESSIBLE. 4.2.6. ALL DUCT JOINTS TO BE SEALED IN ACCORDANCE WITH “SMACNA” STANDARDS AND ACCEPTED GOOD PRACTICE. SEAL CLASS A. ALL DUCT JOINTS TO BE SEALED IN ACCORDANCE WITH “SMACNA” STANDARDS AND ACCEPTED GOOD PRACTICE. SEAL CLASS A. SMACNA” STANDARDS AND ACCEPTED GOOD PRACTICE. SEAL CLASS A. STANDARDS AND ACCEPTED GOOD PRACTICE. SEAL CLASS A. 4.3. FLEXIBLE TYPE DUCT FLEXIBLE TYPE DUCT 4.3.1. FLEXIBLE DUCT IS ONLY ALLOWED IN AREAS WHERE DUCTWORK IS CONCEALED BY A CEILING. FLEXIBLE DUCT IS ONLY ALLOWED IN AREAS WHERE DUCTWORK IS CONCEALED BY A CEILING. 4.3.2. USE OF FLEXIBLE DUCT SHALL BE LIMITED TO NO MORE THAN 5 LINEAR FEET PER RUN. USE OF FLEXIBLE DUCT SHALL BE LIMITED TO NO MORE THAN 5 LINEAR FEET PER RUN. 4.3.3. INSTALL WITH CARE SO AS NOT TO KINK OR COLLAPSE FLEXIBLE DUCT. INSTALL WITH CARE SO AS NOT TO KINK OR COLLAPSE FLEXIBLE DUCT. 5. INSULATION INSULATION 5.1. INSULATION SHALL HAVE A FLAME SPREAD RATING OF 25 OR LESS AND A SMOKE DEVELOPED RATING OF 50 OR LESS IN ACCORDANCE WITH ASTM INSULATION SHALL HAVE A FLAME SPREAD RATING OF 25 OR LESS AND A SMOKE DEVELOPED RATING OF 50 OR LESS IN ACCORDANCE WITH ASTM E84 AND NFPA 90A. 5.2. DUCTWORK INSULATION: DUCTWORK INSULATION: 5.2.1. INSULATE SUPPLY AIR DUCTWORK WITH 1-1/2” THICK STANDARD DUCT WRAP TYPE IV (3/4 LB/FT3 DENSITY) WITH FSK FACING. K FACTOR OF INSULATE SUPPLY AIR DUCTWORK WITH 1-1/2” THICK STANDARD DUCT WRAP TYPE IV (3/4 LB/FT3 DENSITY) WITH FSK FACING. K FACTOR OF THICK STANDARD DUCT WRAP TYPE IV (3/4 LB/FT3 DENSITY) WITH FSK FACING. K FACTOR OF 0.27 AT 75 DEGREES MEAN TEMPERATURE. 5.2.2. ALL EXISTING INSULATION FOR DUCTWORK AND PIPING SYSTEMS PERTAINING TO THIS WORK OR IN THE AREA OF RE-MODEL SHALL BE PATCHED ALL EXISTING INSULATION FOR DUCTWORK AND PIPING SYSTEMS PERTAINING TO THIS WORK OR IN THE AREA OF RE-MODEL SHALL BE PATCHED AND/OR REPLACED AS REQUIRED TO MAINTAIN A VAPOR BARRIER. 6. HVAC CONTROLS HVAC CONTROLS 6.1. CONTROLS WORK TO THE FMS SHALL BE BY ENGIE. CONTROLS WORK TO THE FMS SHALL BE BY ENGIE. 6.2. CONTROLS WORK INTEGRAL TO THE TWO EXISTING REUSED THERMA-FUSERS AND ASSOCIATED THERMOSTAT SHALL BE BY VARITEC. CONTROLS WORK INTEGRAL TO THE TWO EXISTING REUSED THERMA-FUSERS AND ASSOCIATED THERMOSTAT SHALL BE BY VARITEC. 6.3. CONTROLS WORK THAT PROVIDES CONNECTIVITY OF THE FMS TO THE THERMA-FUSER THERMOSTAT SHALL BE BY ENGIE. CONTROLS WORK THAT PROVIDES CONNECTIVITY OF THE FMS TO THE THERMA-FUSER THERMOSTAT SHALL BE BY ENGIE. 6.4. DESCRIPTION OF CONTROLS SCOPE OF WORK: DESCRIPTION OF CONTROLS SCOPE OF WORK: 6.4.1. FMS CONTROLS SHALL BE VIA THE EXISTING DELTA FMS NETWORK THROUGH AN EXISTING DIRECT DELTA NETWORK CONNECTION. FMS CONTROLS SHALL BE VIA THE EXISTING DELTA FMS NETWORK THROUGH AN EXISTING DIRECT DELTA NETWORK CONNECTION. 6.4.2. RELOCATE AND REUSE THE EXISTING THERMOSTAT THAT SERVES EXISTING RTU-1. REFER TO THE DRAWINGS. RE-ESTABLISH THE FMS RELOCATE AND REUSE THE EXISTING THERMOSTAT THAT SERVES EXISTING RTU-1. REFER TO THE DRAWINGS. RE-ESTABLISH THE FMS CONNECTION AND VERIFY THE FUNCTIONALITY. 6.4.3. RELOCATE AND REUSE THE EXISTING THERMA-FUSER THERMOSTAT. REFER TO THE DRAWINGS. PROVIDE CONNECTIVITY BETWEEN WALL-MOUNTED RELOCATE AND REUSE THE EXISTING THERMA-FUSER THERMOSTAT. REFER TO THE DRAWINGS. PROVIDE CONNECTIVITY BETWEEN WALL-MOUNTED THERMOSTAT AND BOTH OF THE RELOCATED THERMA-FUSERS (ONE MASTER AND ONE SLAVE). ADJUST THE VARIABLE VOLUME CFM RANGE SETTINGS IN BOTH THERMA-FUSERS TO 50 CFM MINIMUM AND 200 CFM MAXIMUM. 6.4.4. RE-ESTABLISH THE CONNECTIVITY BETWEEN THE FMS AND THE RELOCATED THERMA-FUSER THERMOSTAT. VERIFY THE FUNCTIONALITY. RE-ESTABLISH THE CONNECTIVITY BETWEEN THE FMS AND THE RELOCATED THERMA-FUSER THERMOSTAT. VERIFY THE FUNCTIONALITY. 7. 7. COMMISSIONING 7. COMMISSIONING COMMISSIONING 7.1. PROVIDE POST-INSTALLATION START-UP AND PERFORMANCE TESTING. PROVIDE POST-INSTALLATION START-UP AND PERFORMANCE TESTING. 7.2. START-UP AND PERFORMANCE TESTING SHALL COMPLY WITH MANUFACTURER REQUIREMENTS AND RECOMMENDATIONS. START-UP AND PERFORMANCE TESTING SHALL COMPLY WITH MANUFACTURER REQUIREMENTS AND RECOMMENDATIONS. 7.3. PROVIDE WRITTEN REPORT THAT DOCUMENTS THE START-UP AND PERFORMANCE TESTS. INCLUDE THIS REPORT IN THE OWNER’S MANUAL.PROVIDE WRITTEN REPORT THAT DOCUMENTS THE START-UP AND PERFORMANCE TESTS. INCLUDE THIS REPORT IN THE OWNER’S MANUAL.S MANUAL.
1. REMOVE EXISTING EXHAUST GRILLE TO ALLOW FOR CEILING REMOVE EXISTING EXHAUST GRILLE TO ALLOW FOR CEILING WORK. REPLACE WITH NEW. 2. REMOVE EXISTING SUPPLY GRILLE TO ALLOW FOR CEILING REMOVE EXISTING SUPPLY GRILLE TO ALLOW FOR CEILING WORK. REPLACE WITH NEW. 3. COMPLETELY REMOVE EXISTING EXPOSED DUCT WORK BACK COMPLETELY REMOVE EXISTING EXPOSED DUCT WORK BACK TO UNIT IN CLOSET TO ALLOW FOR REPLACEMENT. REMOVAL TO INCLUDES BUT IS NOT LIMITED TO ALL DUCT, DIFFUSERS, SUPPORTS, ETC. 4. REMOVE EXISTING LOW RETURN GRILLE UNDER CLOSET TO REMOVE EXISTING LOW RETURN GRILLE UNDER CLOSET TO ALLOW FOR AHU REPLACEMENT. COORDINATE WITH NEW WORK. 5. REMOVE EXISTING VERTICAL GAS FIRE AHU SERVING REMOVE EXISTING VERTICAL GAS FIRE AHU SERVING SECOND FLOOR. REMOVE FROM INSIDE CLOSET TO ALLOW FOR REPLACEMENT WITH NEW UNIT WITH DX COOLING. 6. REMOVE FLUE FROM GAS FIRED WATER HEATER BEING REMOVE FLUE FROM GAS FIRED WATER HEATER BEING REMOVED; SEE NEW WORK PLANS FOR NEW WATER HEATER ON FIRST FLOOR. 7. REMOVE EXISTING VERTICAL GAS FIRE AHU SERVING FIRST REMOVE EXISTING VERTICAL GAS FIRE AHU SERVING FIRST FLOOR. REMOVE FROM INSIDE CLOSET TO ALLOW FOR REPLACEMENT WITH NEW UNIT WITH DX COOLING. 8. REMOVE ROOFTOP EVAPORATIVE COOLING UNIT. SEE NEW REMOVE ROOFTOP EVAPORATIVE COOLING UNIT. SEE NEW WORK PLAN FOR ADAPTING OPENING FOR AHU OUTSIDE AIR SOURCE.
1. REPLACE EXISTING EXHAUST GRILLE REPLACE EXISTING EXHAUST GRILLE 2. REPLACE EXISTING SUPPLY GRILLE REPLACE EXISTING SUPPLY GRILLE 3. NEW EXPOSED ROUND DUCT WORK FROM NEW AHU UNIT NEW EXPOSED ROUND DUCT WORK FROM NEW AHU UNIT IN CLOSET 4. NEW RETURN AIR TO NEW AHU NEW RETURN AIR TO NEW AHU 5. NEW VERTICAL GAS FIRE AHU WITH DX COOLING SERVING NEW VERTICAL GAS FIRE AHU WITH DX COOLING SERVING SECOND FLOOR. INSTALL INSIDE CLOSET. RECONNECT TO EXISTING GAS PIPING. 6. EXTEND NEW FLUE AND SUPPLY AIR TO NEW SEALED EXTEND NEW FLUE AND SUPPLY AIR TO NEW SEALED COMBUSTION GAS FIRED WATER HEATER ON FIRST FLOOR. 7. NEW VERTICAL GAS FIRE AHU WITH DX COOLING SERVING NEW VERTICAL GAS FIRE AHU WITH DX COOLING SERVING FIRST FLOOR. INSTALL INSIDE CLOSET. RECONNECT TO EXISTING GAS PIPING. 8. NEW OUTSIDE AIR ROOFTOP INTAKE FOR REPLACEMENT NEW OUTSIDE AIR ROOFTOP INTAKE FOR REPLACEMENT AHU’S S 9. NEW DX CONDENSING UNITS ON GRADE. NEW DX CONDENSING UNITS ON GRADE.
FLUORESCENT 1'X4' LIGHT FIXTURE TYPE " " UNO; LOWER CASE " " UNO; LOWER CASE UNO; LOWER CASE LETTERS INDICATE SWITCHING GROUP FLUORESCENT 2'X4' LIGHT FIXTURE TYPE " " UNO; LOWER CASE " " UNO; LOWER CASE UNO; LOWER CASE LETTERS INDICATE SWITCHING GROUP FLUORESCENT 2'X2' LIGHT FIXTURE TYPE " " UNO; LOWER CASE " " UNO; LOWER CASE UNO; LOWER CASE LETTERS INDICATE SWITCHING GROUP FLUORESCENT HANGING LINEAR LIGHT FIXTURE TYPE " " UNO; LOWER " " UNO; LOWER UNO; LOWER CASE LETTERS INDICATE SWITCHING GROUP; PROVIDE LENGTH AS SHOWN ON PLANS. WALL SCONCE LIGHT FIXTURE TYPE " " UNO. SEE ARCHITECTURAL UNO. SEE ARCHITECTURAL DRAWINGS/ELEVATIONS FOR MOUNTING HEIGHTS. EXTERIOR WALL LIGHT FIXTURE TYPE " " UNO. MOUNTING HEIGHT AS NOTED UNO. MOUNTING HEIGHT AS NOTED ON PLAN. COORDINATE LOCATION WITH ARCHITECTURAL DRAWINGS/ELEVATIONS. EXIT LIGHT TYPE X1 UNO; PROVIDE NUMBER OF FACES AND DIRECTION OF CHEVRONS SHOWN ON ELECTRICAL AND ARCHITECTURAL DRAWINGS AND AS REQUIRED FOR PATH OF EGRESS. CONNECT TO UNSWITCHED LEG OF LOCAL LIGHT CIRCUIT. LIGHT FIXTURE, TYPE AS NOTED LIGHT FIXTURE - BATTERY EMERGENCY LIGHTING UNIT, TYPE EB SINGLE POLE, THREE WAY SWITCH AND FOUR WAY SWITCH, 20A RATED MOUNT 44" AFF; LOWER CASE LETTER INDICATES SWITCHING GROUP; LETTER "K" INDICATES KEY OPERATED SWITCH WALL SWITCH - DIMMER WALL SWITCH WITH INTEGRAL MOTION/OCCUPANCY SENSOR LIGHTING CONTROL OCCUPANCY SENSOR - CEILING MOUNTED LIGHTING CONTROL OCCUPANCY SENSOR - WALL MOUNTED LIGHTING CONTROL OCCUPANCY SENSOR - EXTENDED RANGE - CEILING MOUNTED (CORRIDORS & ROOMS OVER 400SQFT) LIGHTING CONTROL DAYLIGHT SENSOR - CEILING MOUNTED EMERGENCY LIGHTING RELAY, SEE DETAIL
AutoCAD SHX Text
DUPLEX CONVENIENCE OUTLET, MOUNTED 18" AFF U.N.O. "T" INDICATES TAMPER RESISTANT RECEPTACLE GFI TYPE DUPLEX OR QUADRAPLEX CONVENIENCE OUTLET, MOUNT 18" AFF U.N.O QUADRAPLEX CONVENIENCE OUTLET MOUNT 18" AFF U.N.O. "T" INDICATES TAMPER RESISTANT RECEPTACLE SPECIAL RECEPTACLE, TYPE AS NOTED DISCONNECT SWITCH, NUMBERS INDICATE AMPERAGE/# OF POLES; 30A/3P UNO COMBINATION MAGNETIC STARTER EMERGENCY POWER OFF BUTTON, SEE CODETAIL
AutoCAD SHX Text
FIRE ALARM HORN W/STROBE LIGHT, MOUNT 80" AFF OR 6" BELOW CEILING, WHICHEVER IS LOWER FIRE ALARM MANUAL PULL STATION, MOUNT 44"AFF. FIRE ALARM STROBE LIGHT, MOUNT 80" AFF OR 6" BELOW CEILING, WHICHEVER IS LOWER FIRE ALARM SMOKE DETECTOR FIRE ALARM HEAT DETECTOR FIRE ALARM DUCT DETECTOR W/REMOTE TEST AND INDICATING STATION MAGNETIC DOOR HOLDER FIRE ALARM REMOTE ANNUNCIATOR
AutoCAD SHX Text
VOLUME CONTROL AUDIO VISUAL OUTLET - PROVIDE BACK BOX AND EMPTY 1" CONDUIT STUBBED INTO ACCESSIBLE CEILING SPACE. MOUNT 18" AFF UNO. WALL/SURFACE MOUNTED SPEAKER FOR PA SYSTEM CEILING MOUNTED SPEAKER FOR PA SYSTEM SYNCHRONOUS CLOCK FOR CENTRAL CLOCK SYSTEM KEY PAD FOR INTRUSION DETECTION SYSTEM AUDIO TYPE INTRUSION DETECTION SYSTEM DEVICE DOOR SWITCH/CONTACT FOR INTRUSION DETECTION SYSTEM DATA JACK OUTLET - PROVIDE BACK BOX AND EMPTY 1" CONDUIT STUBBED INTO ACCESSIBLE CEILING SPACE. MOUNT 18" AFF UNO. "W" INDICATES WALL OUTLET MOUNTED 44" AFF. QUADRUPLEX CONVENIENCE OUTLET AND DATA OUTLETS IN FLOOR, WIREMOLD MODEL RFB4-CI UNO. COORDINATE COVER WITH FLOOR FINISH. PROVIDE TWO TVSS TYPE DUPLEX RECEPTACLES. PROVIDE 1-1/4" CONDUIT FROM EACH DATA COMPARTMENT AND STUBBED INTO ACCESSIBLE CEILING SPACE. CABLE TRAY ABOVE DROPPED CEILING, SEE GENERAL SHEET NOTES.
AutoCAD SHX Text
ELECTRIC POWER PANEL JUNCTION BOX TRANSFORMER CIRCUIT BREAKER HOME RUN - 2#12+1#12G IN 3/4"C UNO. BRANCH CIRCUIT RUN CONCEALED IN CEILING AND WALLS - 2#12+1#12G IN 3/4"C UNO. EMERGENCY SYSTEM BRANCH CIRCUIT RUN CONCEALED IN CEILING AND WALLS -2#12+1#12G IN 3/4"C U.N.O. SURFACE MOUNTED PVC RECEPTACLE RACEWAY WITH SIMPLEX RECEPTACLES SPACED AT 12" INTERVALS, 20A RATED 12AWG WIRE. SURFACE MOUNTED WIREWAY, MULTIOUTLET ASSEMBLY, WITH DUAL COMPARTMENTS - COMMUNICATION & POWER; COORDINATE MOUNTING HEIGHT WITH ARCHITECTURAL DETAILS. CONCEAL POWER WIRING AND PROVIDE 1" CONDUIT CONCEALED IN WALL AND STUBBED INTO ACCESSIBLE CEILING SPACE FROM COMMUNICATION COMPARTMENT. PROVIDE GFCI TYPE RECEPTACLES WHEN RECEPTACLE IS WITHIN 10FT OF SINK. DO NOT INSTALL RECEPTACLES BEHIND OR WITHIN 6" OF SINK, PROVIDE DUPLEX RECEPTACLES ON 18" CENTERS UNO. THIN LINED DASHED SYMBOL INDICATES EXISTING TO REMAIN UNO. SEE ELECTRICAL COMMON NOTES ON DRAWING E001 SEE SHEET NOTE #
AutoCAD SHX Text
ELECTRICAL SPECIFICATIONS
AutoCAD SHX Text
SHEET LIST
AutoCAD SHX Text
E-001: ELECTRICAL LEGEND & SPECIFICATIONS ELECTRICAL LEGEND & SPECIFICATIONS EDL-101: ELECTRICAL DEMO LIGHTING FLOOR PLAN ELECTRICAL DEMO LIGHTING FLOOR PLAN EL-101: ELECTRICAL NEW LIGHTING FLOOR PLAN ELECTRICAL NEW LIGHTING FLOOR PLAN EDP-101: ELECTRICAL DEMO POWER FLOOR PLAN ELECTRICAL DEMO POWER FLOOR PLAN EP-101: ELECTRICAL POWER FLOOR PLAN ELECTRICAL POWER FLOOR PLAN E-601: ELECTRICAL SCHEDULES ELECTRICAL SCHEDULES E-701: ELECTRICAL DIAGRAMSELECTRICAL DIAGRAMS
AutoCAD SHX Text
ELECTRICAL LEGEND
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
ABBREVIATIONS
AutoCAD SHX Text
ABBR.
AutoCAD SHX Text
DESCRIPTION
AutoCAD SHX Text
AIR CONDITIONER AMP FUSE CONDENSING UNIT EXISTING PRIME ELECTRICAL CONTRACTOR EXHAUST FAN ENERGY RECOVERY UNIT FAN COIL UNIT GROUND FAULT CIRCUIT INTERRUPTER HEAT PUMP HEATING AND VENTILATING UNIT SUPPLY FAN TAMPER RESISTANT TYPE RECEPTACLE UNIT VENTILATOR UNLESS NOTED OTHERWISE WEATHER PROOF
AutoCAD SHX Text
AC AFU CU (E) EC EF ERU FC GFCI HP HV SF T UV UNO WP
AutoCAD SHX Text
,
AutoCAD SHX Text
S
AutoCAD SHX Text
,
AutoCAD SHX Text
,
AutoCAD SHX Text
S
AutoCAD SHX Text
a
AutoCAD SHX Text
S
AutoCAD SHX Text
3
AutoCAD SHX Text
S
AutoCAD SHX Text
4
AutoCAD SHX Text
S
AutoCAD SHX Text
K
AutoCAD SHX Text
a
AutoCAD SHX Text
a
AutoCAD SHX Text
a
AutoCAD SHX Text
S
AutoCAD SHX Text
OS
AutoCAD SHX Text
O
AutoCAD SHX Text
S
AutoCAD SHX Text
OS1
AutoCAD SHX Text
ER
AutoCAD SHX Text
O
AutoCAD SHX Text
2
AutoCAD SHX Text
S
AutoCAD SHX Text
D
AutoCAD SHX Text
D
AutoCAD SHX Text
L
AutoCAD SHX Text
OS
AutoCAD SHX Text
1. COORDINATE FINAL LOCATION OF ALL DEVICES WITH OWNER AND ARCHITECT WITH RESPECT TO MOUNTING COORDINATE FINAL LOCATION OF ALL DEVICES WITH OWNER AND ARCHITECT WITH RESPECT TO MOUNTING HEIGHTS AND LOCATION OF EQUIPMENT, FURNITURE AND WALL FURNISHINGS. COORDINATE FINAL LOCATION SO AS NOT TO INTERFERE WITH EXHIBIT BOARDS, DRY MARKER BOARDS AND OTHER EXISTING OR NEW SURFACE MOUNTED ITEMS. COORDINATE FINAL LOCATION OF ALL POWER, DATA AND COMMUNICATION OUTLETS WITH OWNER PRIOR TO INSTALLATION. 2. COORDINATE LOCATION OF ALL MECHANICAL, PLUMBING AND FIRE PROTECTION EQUIPMENT WITH THE COORDINATE LOCATION OF ALL MECHANICAL, PLUMBING AND FIRE PROTECTION EQUIPMENT WITH THE RESPECTIVE TRADE CONTRACTORS. 3. ALL NEW ELECTRICAL WIRING DEVICES ARE TO BE RECESSED (FLUSH MOUNTED) IN NEW CONCRETE MASONRY ALL NEW ELECTRICAL WIRING DEVICES ARE TO BE RECESSED (FLUSH MOUNTED) IN NEW CONCRETE MASONRY UNIT (CMU) AND STUD WALL CONSTRUCTION UNLESS NOTED OTHERWISE OR OTHERWISE DIRECTED BY OWNER. 4. PROVIDE FIRE PROOFING AT RATED WALL PENETRATIONS. PROVIDE FIRE PROOFING AT RATED WALL PENETRATIONS. 5. NOTE THAT THE IDENTIFICATION LABELS TO BE USED/MADE FOR ALL SYSTEMS MUST USE THE OWNER'S ROOM NOTE THAT THE IDENTIFICATION LABELS TO BE USED/MADE FOR ALL SYSTEMS MUST USE THE OWNER'S ROOM NUMBERS AND ROOM NAMES, NOT THE NUMBERS OR NAMES ON THE CONSTRUCTION DOCUMENTS. MEET WITH OWNER TO REVIEW AND CONFIRM ROOM NUMBERS AND NAMES PRIOR TO LABELING SYSTEMS. 6. ATTENTION BIDDERS - PROJECT CONSTRUCTION SCHEDULE REQUIREMENTS - INCORPORATE IN BID THE COST ATTENTION BIDDERS - PROJECT CONSTRUCTION SCHEDULE REQUIREMENTS - INCORPORATE IN BID THE COST TO ACCOMMODATE ALL CONSTRUCTION SCHEDULE REQUIREMENTS AS REQUIRED BY SCHEDULING OF WORK DEFINED ON ARCHITECTURAL DRAWINGS AND IN DIVISION 1 SPECIFICATIONS. SUBMISSION OF BID INDICATES COMPLIANCE WITH LISTED DOCUMENTS. 7. PROVIDE 2#10AWG+1#12AWG BRANCH WIRING FOR ALL 20A BRANCH CIRCUITS LONGER THAN 100 FEET PROVIDE 2#10AWG+1#12AWG BRANCH WIRING FOR ALL 20A BRANCH CIRCUITS LONGER THAN 100 FEET (MEASURE LENGTH OF WIRE FROM BREAKER TO FIRST CONNECTION).. 8. THE USE OF METAL CLAD WIRING (MC) IS LIMITED, REFER TO SPECIFICATION DIVISION 26. THE USE OF METAL CLAD WIRING (MC) IS LIMITED, REFER TO SPECIFICATION DIVISION 26. 9. COORDINATE ALL ROOF PENETRATIONS WITH MECHANICAL AND ARCHITECTURAL DETAILS. COORDINATE ALL ROOF PENETRATIONS WITH MECHANICAL AND ARCHITECTURAL DETAILS. 10. COORDINATE ALL WIRING, CONNECTION AND CONTROLS FOR MECHANICAL EQUIPMENT WITH MECHANICAL AND COORDINATE ALL WIRING, CONNECTION AND CONTROLS FOR MECHANICAL EQUIPMENT WITH MECHANICAL AND ATC CONTRACTORS. COORDINATE LOCATION AND INSTALLATION OF CONTROL DEVICES. 11. EACH PRIME TRADE CONTRACTOR BID TO INCLUDE ALL WORK REQUIRED BY ALL OTHER TRADE DOCUMENTS EACH PRIME TRADE CONTRACTOR BID TO INCLUDE ALL WORK REQUIRED BY ALL OTHER TRADE DOCUMENTS ISSUED FOR THIS PROJECT, INCLUDING BUT NOT LIMITED TO ARCHITECTURAL, STRUCTURAL, CIVIL, ROOFING, MECHANICAL, PLUMBING, FIRE PROTECTION, ELECTRICAL DRAWINGS/SPECIFICATIONS/DOCUMENTS. CAREFULLY REVIEW, INCLUDE AND COORDINATE ALL WORK DIRECTED/REQUIRED BY OTHER DOCUMENTS.
AutoCAD SHX Text
(APPLY TO ENTIRE PROJECT)
AutoCAD SHX Text
PROVIDE AN ENCLOSED 120V 20A 1P RELAY ABOVE CEILING TO CONTROL LOCAL EF SO THAT EF WILL OPERATE WHEN LIGHTS ARE 'ON'. CONNECT RELAY COIL TO LIGHTING CIRCUIT. CONNECT FAN POWER CIRCUIT TO INDICATED POWER CIRCUIT. PROVIDE SNAP SWITCH TO OPERATE AS DISCONNECT SWITCH PROVIDE NETWORKED LIGHTING MOTION SENSORS IN CORRIDORS. INSTALL AND GANG WIRE/NETWORK SENSORS IN CORRIDORS SO THAT SWITCH GROUPINGS CORRESPOND TO THE POWER CIRCUITING BREAK SHOWN ON THE PLANS. WIRE LIGHTS TO LOCAL KEY SWITCH. PROVIDE POWER SUPPLIES AND SWITCH PACKS AS REQUIRED. COORDINATE WITH EMERGENCY/NIGHT LIGHTS. PROVIDE CABLE TRAY ABOVE LAY-IN CEILING AND (3) 3"C ABOVE HARD CEILING. SEE "LOW VOLTAGE SYSTEMS WIRING GENERAL NOTES". PROVIDE LOCAL SNAP SWITCH ON UNIT/MOD TO OPERATE AS DISCONNECT SWITCH. PROVIDE 120V POWER CONNECTION/GFI RECEPTACLE TO EWC. COORDINATE WIRING AND FINAL CONNECTION REQUIREMENTS WITH PC. PROVIDE THREE FIRE-RATED PATHWAYS THRU WALL FOR DATA SYSTEMS, SEE "LOW VOLTAGE SYSTEMS WIRING GENERAL NOTES" PROVIDE JUNCTION BOX ABOVE ACCESSIBLE CEILING WITH 120V WIRING FOR FUTURE DOOR ACCESS CONTROL SYSTEM. SEE DETAILS AND COORDINATE ACTUAL INSTALLATION REQUIREMENTS AND FINAL LOCATIONS WITH OWNER AND DOOR INSTALLER. PROVIDE CONCEALED EMPTY CONDUIT FROM DOOR FRAME TO ACCESSIBLE CEILING CAVITY FOR FUTURE WIRING TO POWER HINGE & PANIC DEVICE. PROVIDE CONCEALED EMPTY CONDUIT FROM DOOR HEADER/FRAME TO CEILING ACCESSIBLE CAVITY FOR FUTURE WIRING TO CONTACT SWITCH. SEE DETAILS AND COORDINATE ACTUAL INSTALLATION REQUIREMENTS AND FINAL LOCATIONS WITH OWNER AND DOOR INSTALLER. PROVIDE EXTERIOR FLUSH/RECESSED BACKBOX ADJACENT TO DOOR FOR FUTURE CARD READER; PROVIDE CONCEALED EMPTY CONDUIT FROM BACKBOX TO ACCESSIBLE CEILING CAVITY FOR FUTURE WIRING. SEE DETAILS AND COORDINATE ACTUAL INSTALLATION REQUIREMENTS AND FINAL LOCATIONS WITH OWNER AND DOOR INSTALLER.
AutoCAD SHX Text
(INDIVIDUALLY IDENTIFIED ON DRAWINGS)
AutoCAD SHX Text
1. SEE DRAWING E001 FOR ELECTRICAL LEGEND, GENERAL NOTES AND ELECTRICAL COMMON NOTES. SEE DRAWING E001 FOR ELECTRICAL LEGEND, GENERAL NOTES AND ELECTRICAL COMMON NOTES. SEE ET FLOOR PLANS FOR SPECIFIC LAYOUT AND NOTES FOR CABLE TRAY AND LOW VOLTAGE PATHWAYS. 2. PROVIDE CABLE TRAY ABOVE DROPPED CEILING (OR EXPOSED STRUCTURE) AS SHOWN ON PLANS; PROVIDE CABLE TRAY ABOVE DROPPED CEILING (OR EXPOSED STRUCTURE) AS SHOWN ON PLANS; GENERALLY LOCATED IN CORRIDORS. COORDINATE EXACT LOCATION WITH ALL TRADES, CONSTRUCTION METHODS, STRUCTURE AND EQUIPMENT TO BE INSTALLED UNDER THIS PROJECT. INTERRUPT TRAY, AND PROVIDE (3) 4"C BETWEEN TRAY SECTIONS, IN LOCATIONS WHERE LARGE OBSTRUCTIONS PRECLUDE TRAY INSTALLATION. RESUME TRAY INSTALLATION PAST THE OBSTRUCTION. 3. PROVIDE CONDUIT SLEEVE(S) FOR ALL WALL PENETRATIONS FOR COMMUNICATION, DATA, AND LOW PROVIDE CONDUIT SLEEVE(S) FOR ALL WALL PENETRATIONS FOR COMMUNICATION, DATA, AND LOW VOLTAGE SYSTEMS. COORDINATE WITH CABLE TRAY INSTALLATION. 4. PROVIDE FIRE RATED CABLE PATHWAY DEVICE(S) WITH FIRE PROOFING FOR COMMUNICATION, DATA, PROVIDE FIRE RATED CABLE PATHWAY DEVICE(S) WITH FIRE PROOFING FOR COMMUNICATION, DATA, AND LOW VOLTAGE SYSTEMS AT WALL PENETRATION(S). BASIS OF DESIGN IS SPECIFIED TECHNOLOGIES INC. MODEL 'EZPATH'. COORDINATE WITH CABLE TRAY INSTALLATION. 5. WHERE PROVIDING CONDUIT FOR SYSTEMS WIRING, PROVIDE INSULATING BUSHING ON EACH END WHERE PROVIDING CONDUIT FOR SYSTEMS WIRING, PROVIDE INSULATING BUSHING ON EACH END AND SEAL\CAULK AROUND CONDUIT PENETRATIONS. PROVIDE FIRE SEALANT AT ALL RATED WALL PENETRATIONS AND FIRE SEAL INSIDE CONDUIT AFTER INSTALLING CABLES.
1. REMOVE WALL LIGHT FIXTURE ABOVE SINKS; SEE NEW REMOVE WALL LIGHT FIXTURE ABOVE SINKS; SEE NEW WORK PLANS FOR REPLACEMENT. 2. REMOVE CEILING SURFACE MOUNTED FIXTURE; SEE NEW REMOVE CEILING SURFACE MOUNTED FIXTURE; SEE NEW WORK PLANS FOR REPLACEMENT. 3. REMOVE EXISTING LAY-IN LIGHT FIXTURE; SEE NEW WORK REMOVE EXISTING LAY-IN LIGHT FIXTURE; SEE NEW WORK PLANS FOR REPLACEMENT. 4. REMOVE WALL LIGHT FIXTURE IN STAIRWELL; SEE NEW REMOVE WALL LIGHT FIXTURE IN STAIRWELL; SEE NEW WORK PLANS FOR REPLACEMENT. 5. REMOVE RECESSED DOWNLIGHT FROM DRYWALL CEILING; REMOVE RECESSED DOWNLIGHT FROM DRYWALL CEILING; SEE NEW WORK PLANS FOR REPLACEMENT. (COMPLETE REPLACEMENT, NOT A RETROFIT). 6. REMOVE EXISTING PENDANT HUNG LINEAR LIGHT FIXTURE; REMOVE EXISTING PENDANT HUNG LINEAR LIGHT FIXTURE; SEE NEW WORK PLANS FOR REPLACEMENT. 7. REMOVE EXISTING EXIT LIGHT FIXTURE; SEE NEW WORK REMOVE EXISTING EXIT LIGHT FIXTURE; SEE NEW WORK PLANS FOR REPLACEMENT.
1. REPLACE EXISTING RECEPTACLE WITH NEW GFCI TYPE; SEE REPLACE EXISTING RECEPTACLE WITH NEW GFCI TYPE; SEE NEW WORK PLANS. 2. EXISTING ELECTRIC PANELS TO REMAIN, SEE NEW WORK EXISTING ELECTRIC PANELS TO REMAIN, SEE NEW WORK PLANS.
ScheduleSymbol Label QTY Catalog Number Description Lamp Number
LampsLumensper Lamp LLF Wattage Polar Plot
F1
28 4WSL-LD2-45-UNV-L840-CD1-U
4FT LinearWavestreamSystem, L840
(238) 4000K CCT, 80 CRILEDS ABSOLUTEPHOTOMETRY IS BASED ONCALIBRATION FACTORSCREATED USING LAB LUMENSTANDARDS INGONIOPHOTOMETER WITHTEST DISTANCE OF 28.75FEET
238 19 0.9 39.9
StatisticsDescription Symbol Avg Max Min Max/Min Avg/MinExerciseRoom(Copy) 39.6 fc 46.9 fc 18.6 fc 2.5:1 2.1:1
1. REPLACE EXISTING RECEPTACLE WITH NEW GFCI TYPE. REPLACE EXISTING RECEPTACLE WITH NEW GFCI TYPE. 2. EXISTING ELECTRIC PANELS TO REMAIN, SEE PANEL EXISTING ELECTRIC PANELS TO REMAIN, SEE PANEL SCHEDULE. 3. POWER TO NEW DX CONDENSING UNITS AT GRADE. MOUNT POWER TO NEW DX CONDENSING UNITS AT GRADE. MOUNT NEW DISCONNECT ON WALL. 4. POWER TO NEW WATER HEATER.POWER TO NEW WATER HEATER.
