Ntx 1020

NTX1000NTX2000

Multi-Axis Turning Center

High-Precision, High-Efficiency Integrated Mill Turn Center

NTX1000NTX2000

NTX2000

NTX1000The "52nd Best 10 New Products Awards" sponsored by the Nikkan Kogyo Shimbun

High-Precision, High-Efficiency Integrated Mill Turn Center

Photo: NTX1000/SZM The photo shows the machine outfi tted with options. Actual nameplate layout may differ from the photo.Figures in inches were converted from metric measurements.DDM Direct Drive MotorBMT Built-in Motor TurretORC Octagonal Ram Construction

The birth of the X-class!The X-class has evolved from our best selling N Series that sold 28,000 units.

The X-class machine is designed as a result of thousands of customers feedback on the N Series, and offers high quality, high precision and high reliability.

The X-class machine is a next-generation premium machine with the exibility to meet various needs and worth investment.

Compliance with safety standardsThe X-class machine complies with safety standards of the respective countries around the world. (CE marking, UL, ANSI and other standards)

CE marking: a conformance displayCE: Communaut EuropenneUL: Underwriters Laboratories Inc.ANSI: American National Standards Institute

CONTENTS

04 Mechanism

06 Original technology

07 Features of machine

09 High precision

10 Machining ability

11 Environmental performance

12 OperabilityMaintenance/Peripheral equipment13 MAPPS

14 Diagram

16 Specifications

The NTX Series of high-precision, high-efficiency integrated mill turn

centers is designed for machining small precision parts for medical

equipment and measuring instruments, which have complex shapes

and need high-precision, high-efficiency machining. The NTX

machines offer extensive features including measures against thermal

displacement; an installation footprint 40% smaller than those of

the previous models; and Mori Seiki's original DDM, ORC and BMT

technologies, achieving high-precision complete machining.

NTX2000

NTX1000

NTX1000/NTX2000 3

Main features

4 NTX1000/NTX2000

Y-axis

B-axis

C-axis

A-axis

BW-axis

Spindle 1

Tool spindle

Photo: NTX1000/WZM

Z1-axis X1-axis

X2-axis

Z2-axis

Travel

X1-axis 380 mm (15.0 in.)

Y-axis 210 mm (8.3 in.)

Z1-axis 460 mm (18.1 in.)

B-axis 120

Basic structure

Rapid traverse rate

X1/Y-axis 40 m/min (131.2 fpm)Z1-axis 50 m/min (164.1 fpm)

Tool spindle

X2-axis 160 mm (6.3 in.)Z2-axis 1,402 mm (55.2 in.)

Turret 2

C-axis 360Spindle 1/Spindle 2

A DDS (Direct Drive Spindle) motor is used to turn the spindle directly. A spindle motor placed inside the spindle headstock enables the spindle to be smaller/lighter, and to offer high output while controlling vibration.

Mechanism

Max. tool spindle speed

12,000 min-120,000 min-1 OP

Tool spindle

Tool-clamping force

28,000 N (6,294.3 lbf)(Capto C5)

38 tools76 tools OP 1.2 sec.

Tool-to-tool

ATC/Tool magazine

Tool storage capacity

Please use a dual contact tool when using a No. 40 taper spindle at 15,000 min-1 or higher.

4.4 sec.

Chip-to-chip

DDS: Direct Drive Spindle

NTX1000

X1-axis 495 mm (19.5 in.)

Y-axis 250 mm (9.8 in.)

Z1-axis 1,560 mm (61.4 in.)

B-axis 120

NTX2000

NTX2000NTX1000

NTX1000

X1/Y/Z1-axis 40 m/min (131.2 fpm)NTX2000

X2-axis 155 mm (6.1 in.)Z2-axis 610 mm (24.0 in.)

NTX1000 NTX1000

12,000 min-1 36,000 N (8,092.7 lbf)(Capto C6 OP )

NTX2000 NTX2000

NTX2000NTX1000 NTX1000

1.25 sec.

Workpiece discharge unit

5NTX1000/NTX2000

6-inch8-inch OP

Turret 2

Max. rotary tool spindle speed

6,000 min-1

10 tools Number of tool stations

Spindle 1/Spindle 2 S, SZ, SZM

Chuck sizeSpindle 1

6,000/5,500 min-1

Max. spindle speed (Spindle 1/Spindle 2 )

The center of Spindle 1 always stays in the same position even when the heat is generated.


BW-axis positioning angle (Workpiece discharge unit, Spindle 2)

Allowable rotational speed (The unit rotates dependently on the rotation of Spindle 1)

Max. gripping diameter

100 mm (3.9 in.)1,000 min-1 Only one specifi ed position to stop.

-190-195 : Unload workpiece onto transfer conveyor

0 : Hold workpiece transferred from Spindle 1

-25 : Simultaneous machining

-180 : Transfer workpiece (LS05)

-90 : Avoid interference

The LS-05 and workpiece conveyor are options. Please install the workpiece discharge unit depending on the workpiece shape and chucking condition.

Turret indexing time (1-station)

0.19 sec.

5-inch6-inch OP

Spindle 2

4 positioning angles0, -25, -90, -190-195(0, -25, -90, -180 )

NTX2000

NTX1000

5,000/5,000 min-1

NTX2000NTX1000

8-inch10-inch OP

NTX2000NTX1000

8-inch10-inch OP

OptionOP

6 NTX1000/NTX2000

-120 +120-120 +120

Built-in Motor Turret

Vibration

Heat generated by friction

Lubricating oil outflow

The lubricating oil in the oil pockets which were made by scraping is forced in and out through the gaps because of the contact pressure caused by vibration, generating heat.

Vibration is reduced by converting vibrational energy into heat energy. This helps control chattering caused by vibration.

Lubricating oil

Square guides' excellent damping characteristics

Direct Drive Motor

Transmitting the drive power directly to the rotary axes without

using gears eliminates backlash. Compared with conventional

worm gear systems, this dramatically improves transmission

effi ciency and offers high-speed feed.

Full indexing specifi cation B-axis: with the MSX-701 , up to four axes can be controlled simultaneously. For simultaneous 5-axis control, please use the MSX-711 .

0.49 sec.

B-axis indexing time (90)

100 min-1 B-axis rotational speed

0.0001 Min. indexing increment

High-Flexibility B-axis

120 B-axis rotation range

High-speed rotationHigh-precision indexingLess maintenanceLonger product life

Effects of DDM

Original technology

Original technology

The 4 guideways are located diagonally from each other, so they distort symmetrically in response to the heat generated

by high-speed travel. This means that the center stays in the same position, offering high-speed, high-precision feed.

310 mm (12.2 in.)

Superior damping characteristics

Controls thermal displacement

Achieves high-speed, high-precision feed

Effects of ORC

BMT:Built-in Motor Turret DDM:Direct Drive Motor ORC: Octagonal Ram Construction

Indexingtime:clamping,unclampingtimearenotincluded.

Heat generation

Thermal displacement

The center stays the same

The built-in structure, in which the motor is placed inside the turret, minimizes heat

generation and vibration, improves transmission efficiency and significantly increases

cutting power, speed and accuracy.

Turret temperature increases

1/10 or less Vibration amplitude

Compared with conventional machine

1/3 or lessCompared with conventional machine

Improved milling powerImproved milling accuracyControls the turrets heat and vibration

Reduced energy loss

Effects of BMT

Awarded the 2004 JSME Medal for New Technology

Octagonal Ram Construction

NTX1000

7NTX1000/NTX2000

NTX1000

C

Features of machine

It is possible to perform machining simultaneously with the tool spindle and Turret 2. The interference between the workpiece on the Spindle 1 side and the tool spindle can be avoided by turning the workpiece discharge unit. Spindle 1 and Turret 2

for Process 1

Tool spindle and workpiece discharge unit for Process 2

Simultaneous machining

Variations

T WZW WZM SZS SZM

OptionOP

: Standard features : Not available

Specifications C T W WZ WZM S SZ SZM

Tool spindle/ Spindle 1


Spindle 2

Turret 2

Turret 2 (Milling)

Tailstock

Tailstock

Turret 2 Turret 2

Workpiece discharge unit Spindle 2

Machining process from bar stock to the finished workpiece

Feed a workpiece from the Spindle 1 side, and perform machining.

Transfer/cut-off

Transfer the workpiece to the workpiece discharge unit, and perform cutting-off.

Back side milling

Back side milling on the workpiece discharge unit.

Eject workpiece to chuter

After milling is completed, turn the workpiece discharge unit, and eject the workpiece to the chuter.

Workpiece discharge unit for back side milling

21

3 4

Bar feed/machining

Transfer conveyor OP(Bar feeder specifications)

8 NTX1000/NTX2000

Loading

Replacement of slug stock

Turn the workpiece discharge unit, and load a workpiece.

Supply workpiece to Spindle 1

Transfer the workpiece from the workpiece discharge unit to Spindle 1.

Machining on the Spindle 1 side

Machine the workpiece with the tool spindle and Turret 2 on the Spindle 1 side.

Back side milling/Unload workpiece

Transfer the workpiece from Spindle 1 to the workpiece discharge unit, and machine the back side of the workpiece. After that, turn the workpiece discharge unit, and unload the workpiece.

21

3 4

Slug stock

Finished workpiece

Available only for W specifications equipped with LS-05.

Slug stock Finished workpiece

Back end hand OP

NTX2000

: Standard features: Not available

Specifications T TZ TZM S SZ SZM

Tool spindle/Spindle 1

Spindle 2

Turret 2

Turret 2 (Milling)

Tailstock

Tailstock

T

Variations

Turret 2

TZ TZM

Spindle 2

S

Turret 2

SZ SZM

Space-saving Simultaneous machining

NTX1000

It is possible to use the tool spindle on the Spindle 2 side and Turret 2 on the Spindle 1 side simultaneously.

Features of machine

NTX2000/1500SZApprox. 12.1 m2

NT4200 DCG/1500SZApprox. 17.3 m2

Compared with conventional machine

Approx. 30 smaller

(Approx. 130.2 ft2) (Approx. 186.2 ft2)

9NTX1000/NTX2000

NTX1000

0.01 m Resolution

OptionOPHigh precision

High-precision equipment

Coolant cooling system (Separate type)

The ball screw core cooling system circulates cooling oil through the support bearings,

maintaining high-precision machining.

Ball screw core cooling

The coolant temperature rises because of heat generated by machining. Circulating the coolant also raises the temperature. Increases in

the oil temperature have a major effect on thermal displacement in the machine and the dimensional accuracy of the workpiece. This unit

prevents the coolant from heating. When using oil-based coolant, the oil temperature can become extremely high even with the standard

coolant pump, so we strongly recommend this unit.

Please consult with your Mori Seiki representative if you are using oil-based coolant.

We cannot guarantee that this unit will completely control the coolant temperature. It is designed to help prevent oil temperature increases.

The absolute magnetic linear scale (full closed-loop control) made

by Magnescale is effective for high-precision positioning, and is

available as an option.

Direct scale feedback OP

OP

Roundness

10 mFilter: 150

90

270

180 0

Milling (Actual results)

Tool End mill

Tool diameter 16 mm ( 5 /8 in.)

Material Brass

Spindle speed 8,000 min-1

Feedrate 2,000 mm/min (78.7 ipm)

High-precision data

The cutting test results indicated in this catalog are provided as examples. The results indicated in this catalog may not be obtained due to differences in cutting conditions and environmental conditions during measurement.

SVC: Smooth Velocity Control

2.10 m

Tool center point control/Cutting point command (Standard features for MSX-711 )SVC function (Standard feature for MSX-711 )

Main featuresThe tool path can be controlled from the tool center point.

No reprogramming is needed when the tool length and the tool diameter are changed.

NC automatically calculates cutter radius compensation and tool length offsets based on the program commands for tool tip control.

Tool length offset

Cutter radius compensation

Tool center point

Gauge lineThe SVC function, in which the program commands for tool tip control

are read in advance and compensation is automatically applied to achieve

smooth tool feed, is equipped as standard. By combining this function

with DDM (Direct Drive Motor), the machine offers greatly improved

surface quality and reduced cycle time during 5-axis machining.

Motion of the SVC function

WorkpieceWorkpiece WorkpieceWorkpiece

OFF ON

The SVC function includes the following functions:AI contour control Nano smoothing Smooth TCPMachining mode selection G332 tolerance command

Tool length offset

Cutter radius compensation

Cutting point

Gauge line

Tool center point control Cutting point command

Main featuresThe tool path can be controlled from the cutting point.

By using cutting point commands, machining using radius end mills or square end mills can be performed without reprogramming when tool length, cutter radius or tool tip corner R are changed.

Heat

Cooling oil

Heat

Ball screw

Contouring precision

10 NTX1000/NTX2000

Machining ability

Cutting test

JIS: Japanese Industrial Standard The cutting test results indicated in this catalog are provided as examples. The results indicated in this catalog may not be obtained due to differences in cutting conditions and environmental conditions during measurement.

Material : S45C (Carbon steel)

Material removal rate 48 mL/min (2.9 in3./min)Tool diameterSpindle speedFeedrateDepth of cut

20 mm ( 3/4 in.)400 min-1

96 mm/min (3.8 ipm)25 mm (1.0 in.)

End mill

Face mill

Material : A5052 (Aluminum)

Material removal rate 384 mL/min (23.4 in3./min)Tool diameterSpindle speedFeedrateDepth of cut

80 mm (3.1 in.)12,000 min-1

10,000 mm/min (393.7 ipm)0.6 mm (0.02 in.)


Tool diameter 20 mm (3/4 in.)Material removal rateSpindle speedFeedrate

37 mL/min (2.3 in3./min)400 min-1

120 mm/min (4.7 ipm)

Drill

Heavy-duty cutting (O.D.)


Material removal rate 318 mL/min (19.4 in3./min)Spindle speedFeedrateDepth of cut

682 min-1

0.4 mm/rev (0.02 ipr)6.0 mm (0.24 in.)

NTX1000

11NTX1000/NTX2000

Reduction in environmental burden

Environmental performance

eco friendlyTo conserve limited resources and protect global environment

The NTX Series pursues a high "environmental performance" that is required of machine tools.

Energy saving function LED lighting

While ensuring effi cient operation, it reduces power consumption. LED with high luminous effi ciency offers a high light output at a low wattage,

contributing to reducing electricity use.

If the operation panel is not touched for a certain amount of time, the interior light turns off. This saves energy and lengthens the life of the machine lights.

If the keyboard is not touched for a certain amount of time and NC operation is not being performed, power is cut off to the servo motor, the spindle, the coolant pump and the chip conveyor, thereby saving energy.

Automatic machine light function

Automatic sleep function

12 NTX1000/NTX2000

OperabilityMaintenance Peripheral equipment

Peripheral equipment

Specifications

Workpiece material and chip size: Suitable : Not suitable

Steel Cast iron Aluminum, non-ferrous metal

Long Short Powdery Short Long Short Powdery

Hinge type Hinge type + Scraper type + Drum filter type

Chip size guidelines

Short: chips 50 mm (2.0 in.) or less in length,

bundles of chips 40 mm (1.6 in.) or lessLong: bigger than the above

The chip conveyor is right disposal only. The options table below the general options when using coolant. Changes may be necessary if you are not using coolant, or depending on the amount of coolant, compatibility with machines, or the specifications required.

Please select a chip conveyor to suit the shape of your chips. When machining special or difficult-to-cut material (cutting hardness HRC 45 or higher), please consult with your Mori Seiki representative. We have prepared several options for different chip shapes and material. For details, please consult with your Mori Seiki representative.

OPExternal chip conveyor

OperabilityMaintenance

OperabilityMaintenance

Magazine

The tool magazine is placed on the front side of the machine so that the operator can check and exchange tools at the operating position.

Coolant tank

The coolant tank can be pulled toward the front side of the machine.

Equipment layout

Oil cooler

Hydraulic unit Lubricating oil unit

Pneumatic deviceElectrical cabinet

1 If a workpiece diameter is smaller than 50 mm (2.0 in.), it is necessary to change hand jaw setups.

2 If a workpiece length is more than 80 mm (3.1 in.), there will be restrictions on the operation.

LS-05 LG-10

Workpiece diameter

Min. mm (in.) 20 (0.8)1 20 (0.8)

Max. mm (in.) 100 (3.9) 200 (7.8)

Workpiece length

Min. mm (in.) 20 (0.8) 10 (0.4)

Max. mm (in.) 120 (4.7) 110 (4.3)2

Max. transfer weight kg (lb.) 5 (11.0) 10 (22.0)2

Workpiece stocker 10 pallets Stackable 10 pallets

Type of hand Single hand Back end hands

Jaw stroke mm (in.) 70 (2.8) 20 (0.8)

OPLoader type

We have prepared two types of loader specifications: a workpiece stocker integrated type LS-05, and a separate type LG-10.

LS-05 does not require additional installation space because the workpiece stocker is integrated into the machine.

LS-05 (Smart loader) LG-10 (Gantry loader)

The equipment layout is designed for daily operation and maintenance.

Operability

Access to the Magazine Door opening width Access to the spindle Swivel-type operation panel

Tool change is possible from both sides of the magazine.

The wide door opening 697 mm (27.4 in.) allows easier loading and unloading of workpieces and maintenance inside the machine.

The machine offers much better access to the workpiece, with the distance from the front of the machine to the spindle center of 385 mm (15.2 in.).

A swivel-type operation panel provides easier setup.

385 mm(15.2 in.)697 mm (27.4 in.)

115

13NTX1000/NTX2000

MAPPS

A New High-Performance Operating System

for Integrated Mill Turn Centers

19-inch operation panel

A new high-performance operating system that pursues ease of use, and combines the best hardware in the industry with the advanced application/network systems.

Vertical soft-keys

File display and Memo function

MAPPS Camera

Alarm help function

Keyboard

Vertical soft-keys are arranged on the left and right sides of the screen. The vertical soft-keys can be used as option buttons or shortcut keys to which you can assign your desired screens and functions, allowing you to quickly display the screen you want.

Images taken by cameras installed inside/outside the machine can be displayed on the programming screen. This function is useful for maintenance.

Checks for interference in 3D for spindles, workpieces, soft jaws, tools, holders and turrets. Since the machine will stop when interference is detected either in manual or in automatic mode, we have achieved the worlds safest system against interference.

MAPPS is packed with new functions for easier setup and maintenance, including the File Display and Memo function that displays operating instructions and manuals on the screen and the Alarm help function that provides instructions when alarms occur.

A PC-type keyboard is used as standard, making key input easy. A keyboard with a conventional key layout is also available as an option.

Outstanding operability thanks to upgraded hardware Enhanced functionality by using CAM software New functions for easier setup and maintenance Machine interior and exterior can be monitored on the screen

(option)

3D interference checking function

Interference occurredRunning

The 3D interference checking function will check for interference accurately as long as the 3D model exactly matches the actual configuration of the spindles, workpieces, soft jaws, tools, holders and turrets.

Customized design is required for special shape. For details, please refer to the description of 3D interference checking function in the NC control unit specifications.

A cutting simulation that shows how material is removed as machining proceeds cannot be carried out during a 3D interference check.

Possible camera installation points Inside machine

(to check machining)

Chip bucket (to check chip accumulation)

Tool magazine (to check cutting tools)

Other points requested by customers

Please contact Mori SeikiOP

Outstanding operability

Functions for multi-axis machining

Improved ease of setup and maintenance

Faster creation of programs

Improved work effi ciency

MAPPS Mori Advanced Programming Production System

OptionOP

Applicable Operating Systems: Windows Vista Business / Ultimate, Windows 7 Professional / Ultimate

A PC is required to use ESPRIT. Please prepare PCs by yourself.

ESPRIT allows you to create complex 3D programming with high-added value. By just installing the software on your PC with connection to LAN, you will be able to use it. (Once the software is started on the computer, it can be used for up to 7 days without LAN connection.)

Postprocessor as standard

CAM software will be ready to use once your machine is installed

Cost for introducing CAM software can be saved

ESPRIT data can be modifi ed on the machine (through Remote Desktop connection)

The software can be installed on multiple PCs on the network (It cannot be simultaneously started up on more than one PC)

2-year warranty support (including free update)

CAM software

The photo shown may differ from actual machine. Information about the screen is current as of October 2010.

NTX1020_EA01V_MAP.indd 1 10.10.8 4:10:36 PM

MAPPS OptionOP

14 NTX1000/NTX2000

2626

(103

.4)

4076 (160.5)

63 (2.5)

A

B

2980 (117.3)

2626

(103

.4)

4076 (160.5)

63 (2.5)

A

B

2980 (117.3)

2710 (106.7)

B

2412

(95.0)

2424 (95.4)

Spindle centerSpindle center

A

Side view

2710 (106.7)

B

2412

(95.0)

2424 (95.4)

Spindle centerSpindle center

A

mm (in.)Installation diagrams (NTX1000)

Diagrams

mm (in.)Installation diagrams (NTX2000)

Plan view

Front view Side view

Chip conveyor (Consep2000)

Chip conveyor (Consep2000) EN Standards

A Machine width 5,466 (215.2)

B Discharge height of chip conveyor 1,043 (41.1)

Chip conveyor (Consep2000)

Chip conveyor (Consep2000) EN Standards

A Machine width 3,904 (153.7) 4,143 (163.1)

B Discharge height of chip conveyor 1,064 (41.9) 1,026 (40.4)

Plan view

Front view

15NTX1000/NTX2000

50

10

5

1100 1000

2400

10000 2000012000

1450

1950

50T=49.4 Nm (36.4 ftlbf)

T=36.7 Nm (27.1 ftlbf)

T=21.9 Nm (16.2 ftlbf)

T=19.1 Nm (14.1 ftlbf)

10 kW (13.3 HP)9 kW (12.0 HP)7.5 kW (10 HP)

5.5 kW (7.5 HP)

3.7 kW (5 HP)

2.2 kW (3 HP)1.8 kW (2.4 HP)1.1 kW (1.5 HP)

1

4500

Torque (N

m)

Output (k

W)

Tool Spindle speed (min-1)

50

10

5

1100 1000 1950 5000 12000

10000

1450

1

50

10

T=49.4 Nm (36.4 ftlbf)

T=36.7 Nm (27.1 ftlbf)

T=21.9 Nm (16.2 ftlbf)

T=19.1 Nm (14.1 ftlbf) 9 kW (12.0 HP)

2400

7.5 kW (10 HP)

7.5 kW (10 HP)

4500

5.5 kW (7.5 HP)

Torque

(Nm

)

Output (k

W)

Tool Spindle speed (min-1)

Spindle speed-torque/output-rotation speed diagram (NTX1000)

Q43475A01

Spindle drive motor: 9/5.5 kW (12.0/7.5 HP) Max. spindle speed: 12,000 min-1

Spindle drive motor: 9/5.5 kW (12.0/7.5 HP) Max. spindle speed: 20,000 min-1

T=223 Nm (164.5 ftlbf)

T=172 Nm (126.9 ftlbf)

T=158 Nm (116.5 ftlbf) 11 kW (15 HP)

7.5 kW (10 HP)

100 1000 60001400

453

470610

50

100

200

300

5

10

20

30

Torque (N

m)

Output (k

W)

Spindle speed (min-1)

50

10

5

1

50

10

5

11000100 60001950

T=49.4 Nm (36.4 ftlbf)

T=36.7 Nm (27.1 ftlbf) T=21.9 Nm (16.2 ftlbf)

7.5 kW (10 HP)

5.5 kW (7.5 HP)

24001450

1200Ou

tput (k

W)

Spindle speed (min-1)

Torque (N

m)

Q43396A01

Spindle drive motor: 11/11/7.5 kW (15/15/10 HP) Max. spindle speed: 6,000 min-1

Spindle 1

Q43490A01

Spindle drive motor: 7.5/5.5 kW (10/7.5 HP) Max. spindle speed: 6,000 min-1

Spindle 2

Tool spindle (Standard)

10

5

1

0.5

10

5

1

0.5100 1000 3000 6000

T=4.8 Nm (3.5 ftlbf)

T=2.3 Nm (1.7 ftlbf)

1.5 kW (2 HP)

1.2 kW (1.6 HP)

Torque (N

m)

Output (k

W)

Spindle speed (min-1)Q43487A01

Spindle drive motor: 1.5/1.2 kW (2/1.6 HP) Max. spindle speed: 6,000 min-1

Turret 2 rotary tool spindle

Tool spindle (High-speed) OP

Q43474A01

OptionOP

16 NTX1000/NTX2000

Spindle 26,000 min-1: 11/7.5 kW (15/10 HP) Spindle cooling system

Turret 2 10-station, bolt-tightened turret

Rotary tool spindle6,000 min-1: 1.5/1.2 kW (2/1.6 HP)

Workpiece holding device

Hydraulic chuck

Workpiece discharge unit (5-inch) Spindle 2 (5-inch) Spindle 2 (6-inch)

Chuck high/low pressure system

Workpiece discharge unit Spindle 2

Hydraulic steady rest

SLU-1Z

SLU-1Z Interface SLU-1Z

SLU-2Z

SLU-1Z Interface

SLU-2Z Interface

Tailstock/Tailstock spindle

Tailstock spindleLive center specifications:MT4(Center not included)

Built-in center: MT3(with Center) Tailstock drilling (for live center use only) Foot switch for tailstock

CoolantCoolant system (Turret 2) 635/1,040 W (50/60 Hz)

Measurement

Automatic in-machine tool presetter (In-out type)

For tool spindle For tool spindle + Turret 2

Automatic operation supportWorkpiece discharge unit Workpiece discharge unit, Back end hand (including 1 workpiece rest)

High-precision controlDirect scale feedback (Turret 2) X, Z-axis

OthersRotary-tool holders Rotary-tool holders (Oil hole)

Standard & optional features (NTX1000)

NTX1000/SZ

NTX1000/W

NTX1000/T

NTX1000/WZ

NTX1000/WZM

NTX1000/S

NTX1000/SZM

NTX1000/C

: Standard features : Option : Please contact Mori Seiki: Not available

Specifications

Some options are not available in particular regions. For details contact Mori Seiki. The information in this catalog is valid as of October 2010. The details given above are subject to change without notice.

Spindle 16,000 min-1: 11/7.5 kW (15/10 HP) Spindle cooling system

Tool spindle12,000 min-1: 9/5.5 kW (12.0/7.5 HP) 20,000 min-1: 9/5.5 kW (12.0/7.5 HP)

B-axis min. indexing incrementFull indexing specifications With B-axis direct scale feedback

Spindle cooling system

Workpiece holding deviceSoft jaws

Hydraulic chuckSpindle 1 (6-inch) Spindle 1 (8-inch)

Chuck high/low pressure system Spindle 1

Tool magazine

Tool storage capacity38 tools 76 tools

ATC

Type of tool shankCapto C5 HSK-A50 (T50)

CoolantCoolant system (Tool spindle) 635/1,040 W (50/60 Hz) Coolant in upper part of chuck (Spindle 1)

Super-high pressure coolant system

635/1,040 W (50/60 Hz) 3.5/7.0 MPa (507.5/1,015 psi) Specifications for switching standard pressure and super high pressure

Super-high pressure coolant system interface3.5/7.0 MPa (507.5/1,015 psi) 7.0 MPa (1,015 psi)

Coolant flow switch For Super-high pressure coolant system Coolant float switch Oil skimmer

Coolant cooling system (Separate type, Panasonic)Optional when using water-soluble coolant Compulsory when using oil-based coolant (Please consult with your Mori Seiki representative)

Coolant cooling system interface (Other than Panasonic) Mist collector

HVS-150 Including stand Mist collector interface

Chip disposalChip conveyor interface

Chip conveyorRight discharge, Hinge type Right discharge, Hinge type + Scraper type + Drum filter type

Air blowChuck (Spindle 1) Tool tip (Tool spindle)

Chip bucket (for chip conveyor) Coolant gun

When the tool tip air blow is regularly used, air supply of more than 300 L/min (79.2 gpm) is separately required.

MeasurementManual internal tool presetter In-machine measuring system (Tool spindle) Optical type touch sensor (Renishaw)

Operation support device/functionAutomatic power off device Automatic door Weekly timer

External M-code5 10

Automatic operation supportTransfer conveyor (Bar feeder specifications) Bar feeder interface Guide bushing (solid, with spacer) Work stopper (in spindle)

High-precision controlDirect scale feedback (Tool spindle) X, Y, Z-axis

Safety featuresFull cover Impact resistant viewing window Door interlock system Chuck jaw stroke end check

Used only when optional chuck/cylinder is selected

Cylinder check valve Low hydraulic pressure detection switch Low air pressure detecting switch Earth leakage breaker

Danger sensing device interfaceRecommended when oil-based coolant is used or during unmanned operation.

OthersBuilt-in worklightLeveling blockHand toolsTool holders SMC Refrigerating type air dryer Temperature conditioner in electrical cabinet Signal tower 3 layers Red, yellow, green

Chuck foot switch1 foot switch 2 foot switches

Manual pulse generator (separate type) External time accumulator (during automatic operation)

17NTX1000/NTX2000

Some options are not available in particular regions. For details contact Mori Seiki. The information in this catalog is valid as of October 2010. The details given above are subject to change without notice.

Standard & optional features (NTX2000)Spindle 1

5,000 min-1 22/18.5 kW (30/24.7 HP)


Tool spindle

12,000 min-1 18.5/11 kW (24.7/15 HP)

B-axis min. indexing incrementFull indexing specifications (0.0001) With B-axis direct scale feedback



Soft jaws

Hydraulic chuckSpindle 1 (8-inch)

Spindle 1 (10-inch)

Chuck high/low pressure systemSpindle 1 (8-inch)

Spindle 1 (10-inch)

Tool magazine

Tool storage capacity38 tools (chain-type)

76 tools (chain-type)

ATC

Type of tool shank

BT40

Capto C6

HSK-A63

Coolant

Coolant system (Tool spindle) 635/1,040 W (50/60 Hz)

Coolant in upper part of chuck Spindle 1

Super-high pressure coolant system

635/1,040 W (50/60 Hz)

3.5/7.0 MPa (507.5/1,015 psi)

Interface (Ogura Clutch)

Interface (KNOLL)

Coolant flow switch For super-high-pressure coolant

Coolant float switch

Oil skimmer

Coolant cooling system (separate type)

Optional when using water-soluble coolant

Compulsory when using oil-based coolant (Please consult with your Mori Seiki representative)

Mist collectorWater-soluble coolant: HVS-220 Oil-based coolant: HVS-300

Chip disposal

Chip conveyor interface

Chip conveyor

Right discharge, Hinge type

Right discharge, Hinge type+Scraper type+Drum filter type

Air blowChuck (Spindle 1)

Tool tip (Tool spindle)

Chip bucket (for chip conveyor)

Coolant gun

When the tool tip air blow is regularly used, air supply of more than 300 L/min (79.2 gpm) is separately required.

Measurement

Manual internal tool presetter Spindle 1 (removable)

Automatic in-machine tool presetter Tool spindle

In-machine measuring system (Tool spindle) Optical type touch sensor (Renishaw)

Operation support device/function

Automatic power off device

Automatic door

Weekly timer

External M-code5

10

Automatic operation support

Bar feeder interface

Parts catcher

Guide bushing (solid, with spacer)

Work stopper (in spindle)

High-precision control

Direct scale feedback (Tool spindle) X, Y, Z-axis

Safety features

Splash guard

Impact resistant viewing window

Door interlock system

Chuck jaw stroke end checkOnly available when the hydraulic chuck cylinder is selected as an option

Cylinder check valveOnly available when the hydraulic chuck cylinder is selected as an option

Low hydraulic pressure detection switch

Low air pressure detecting switch

Earth leakage breaker

Danger sensing device interfaceRecommended when oil-based coolant is used or during unmanned operation

Others

Built-in worklight (LED)Leveling blockHand toolsTool holders

SMC Refrigerating type air dryer

Temperature conditioner in electrical cabinet

Signal tower 3 layers Red, yellow, green

Chuck foot switch1 foot switch

2 foot switches

Manual pulse generator (separate type)

Spindle 2

5,000 min-1 22/18.5 kW (30/24.7 HP)

Turret 2

10-station, bolt-tightened turret

Rotary tool spindle6,000 min-1 1.5/1.2 kW (2/1.6 HP)


Hydraulic chuckSpindle 2 (8-inch)

Spindle 2 (10-inch)

Chuck high/low pressure systemSpindle 2 (8-inch)

Spindle 2 (10-inch)

Steady rest

Programmable SLU1

Programmable SLU2

Programmable SLU3.1

Programmable SLU1 Interface

Programmable SLU2 Interface

Programmable SLU3.1 Interface

Turret 2 SLU1

Turret 2 SLU1 Interface

Coolant

Coolant in upper part of chuck Spindle 2

Chip disposal

Air blow Chuck (Spindle 2)

Measurement

Manual internal tool presetter Spindle 2 (removable)

Automatic in-machine tool presetter Turret 2

High-precision control

Direct scale feedback (Turret 2) X, Z-axis

NTX2000/SZ

NTX2000T

NTX2000/TZ

NTX2000/TZM

NTX2000/S

NTX2000/SZM

: Standard features : Option : Please contact Mori Seiki: Not available

18 NTX1000/NTX2000

Specifications

Numerical control unit specifications (MSX-701 , MSX-711 )Controlled axes

Controlled axesH1: X, Z, C, Y, B, A, BW

H2: X, Z, C

Simultaneously controllable axes

H1: 4 axes (MSX-701 )

H1: 5 axes (MSX-711 )

H2 3 axes

Least input increment

X, Z, Y, A: 0.001 mm (0.0001 in.)

B: 0.0001 (Full indexing)

C: 0.0001

Max. command value 99,999.999 mm (9,999.9999 in.)

Software damper Abnormal load detection

Programming resolution multiplied by 1/10

X, Z, Y, A: 0.0001 mm (0.00001 in.)

B: 0.0001 (Full indexing)

C: 0.0001

Stroke limit check before movement

H1: Tool spindle (Turret 1) sideH2: Turret 2 side

Operation

Manual handle interruption

Program restart

Sequence number comparison and stop

Tool axis direction handle feed

Interpolation functions

Nano interpolation

Helical interpolationG02, G03 Circular interpolation + linear interpolation

Threading, synchronous cutting G32

Cylindrical interpolation G07.1 (G107)

Multiple thread cutting G32

Thread cutting retract

Continuous thread cutting

Polar coordinate interpolation G12.1, G13.1 (G112, G113)

Involute interpolation G02.2, G03.2

Spiral/conical interpolation G02, G03

Smooth interpolation G05.1

NURBS interpolation G06.2

Installation of high-speed skip terminal

Tool spindle Cs control Including Cs contour control and Normal direction control

Single direction positioning

Variable lead threading G34

Circular threading G35, G36

Polygon turning between the spindles G50.2, G51.2

Spindle 1 hob function G80.4, G81.4

Feed functions

Tangential speed constant control

Feedrate override 0 200 (10 increments)

Override cancel

AI contour control

Program input

Program number

4 digits O code

8 digits O codeSequence change is required

Sequence number 5 digits N code

Absolute/incremental programming X (U), Z (W), C (H), Y (V), B, A

Decimal point inputDecimal point programming or electronic calculator type decimal point programming can be set using parameters

Diameter/radius programming (X-axis) Radius programming is possible with parameters

Plane selection G17, G18, G19

Rotary axis designation

Rotary axis roll-over

Local coordinate system setting G52

Machine coordinate system selection G53

Workpiece coordinate system selection G54 G59

Additional workpiece coordinate systems 48/300 sets

Programmable data input G10

Sub-program call Up to 10 nestings

Hole machining canned cycle G80, G83 G89

Hole machining canned cycle for NT G460 G464

Single canned cycle

Multiple canned cycle

Multiple canned cycle Pocket profile, zigzag thread cutting

F15 format

Custom macro common variables : 600 Programs

#100 #199, #500 #999

3-D coordinate conversion

Dynamic diameter/radius switching G10.9

Addition of optional block skip Soft key type (2 9)

Interruption type custom macro

Programmable mirror image G50.1, G51.1

ScalingG50, G51The G code will be type B system

Coordinate system rotation

Automatic corner override G62

High-speed canned cycle

MORI-POST Advanced mode

Islands, open pockets

DXF import function

Text Engraving Function

Relief machining

19NTX1000/NTX2000

: Standard : Option: Not available

High-speed/High-precision/5-axis machining functions MSX-701 MSX-711

Interpolation functions

Nano smoothing G05.1

Feed functions AI contour control

Program input Tilted working plane commandG68.2G53.1G69.1

Tool functions/ Tool offset functions

Tool center point controlG43.4G43.5G49

3-D cutter compensation

G40G41.2G41.6G42.2G42.6

SVC function

Workpiece position error compensation G54.4

Data input/output

Fast data server

Memory card for Data server

Fast data server + Memory card for Data server

CF card 1 GB + ATA adapter The information in this catalog is valid as of September 2010. The details given above are subject to change without notice.

Miscellaneous functions/Spindle speed functions

Spindle speed override 50 150% (10% increments)

Spindle 1 orientation

Spindle 2 orientation

Synchronous tappingTool spindle

Turning spindle

Multiple M cords in single block (Multi M code function) Available for specific M codes

Tool functions/Tool offset functions

Tool functions 4 digits T code

Number of tool offsetsH1: 240 sets

H2: 64 sets

Number of tool offsets total H1: 480/720/996 sets

Tool geometry offset/Tool wear offset

Tool nose radius offset G40 G42

Tool offset

Y-axis offset

Tool life management B

Number of tool groups for tool life management B 240 sets

Corner circular interpolation G39

Cutting point interpolation for cylindrical interpolation

MAPPS Tool management system1

MAPPS Tool management system1 + Tool IC (MAPPS software only)2

MAPPS Tool management system1 + Tool ID (MAPPS software only)2

1 Not available for Turret 2 2 Separate consultation is required if hardware and software are customizedH1: Tool spindle (Turret 1) sideH2: Turret 2 side

Editing

Expanded program editing Copy buffer: 10 kB

Background editing

Machining time stamp

Playback

Undo/Redo function

Line number display

Setting and display

Status display

Clock function

Actual position display

Program comment display 190 characters

Parameter setting display

Alarm display

Alarm history display

Operator message history display

Operation history display

Running time/Parts count display

Actual feedrate display

Self-diagnosisIncludes alarm display, I/O signal diagnosis and ladder diagram

Operation panel: Display section 19-inch TFT color LCD

Multi-counter display

Data input/output

Memory card input/output

Ethernet10/100/1000BASE-TAccess to user memory area by Ethernet function with MORI-SERVER Software

DNC operation by the memory card

Memory card for MAPPS

6 GB Program storage area (for card DNC operation, for data backup)

Files up to 10 MB in size can be edited

20 GB Program storage area (for card DNC operation, for data backup)

Files up to 10 MB in size can be edited

CF card (4 GB/2 GB/512 MB) + ATA adapter

3D interference checking function

Machine model for interference checkingStandard internal cover, tool spindle, spindle, turret, workpiece discharge unit

Special designs require additional consultation

Program storage length and registerable programs

Part program storage length Registerable programs

320 m (1,050 ft) 250MSX-701

MSX-711

640 m (2,100 ft) 500MSX-701

MSX-711

1,280 m (4,200 ft) 1,000

2,560 m (8,400 ft) 1,000/2,000

5,120 m (16,800 ft)

1,000/4,000 10,240 m (33,600 ft)

20,480 m (67,200 ft)

CAM software

ESPRIT

20 NTX1000/NTX2000

Specifications

Machine specificationsItem

NTX1000C T W WZ WZM

Capacity

Max. swing of workpiece mm (in.) 370 (14.5)Swing over cross slide mm (in.) 370 (14.5) 370 (14.5) Max. turning diameter mm (in.) 370 (14.5) 370 (14.5)Max. turning length mm (in.) 424 (16.6)

Bar work capacity mm (in.) 52 (2.0) [65 (2.5)]

Travel

X-axis (Tool spindle) mm (in.) 380 (15.0)

Y-axis (Tool spindle) mm (in.) 105 (4.1)

Z-axis (Tool spindle) mm (in.) 460+155 (18.1+6.1)

B-axis (Tool spindle) 120

(X2-axis (Turret 2)) mm (in.) - 155 (6.1)

(Z2-axis (Turret 2)) mm (in.) - 610 (24.0)

BW-axis 4 positioning angles

Spindle 1

Max. spindle speed min-1 6,000[5,000]

Number of spindle speed ranges 2

Spindle nose JIS A2-5[JIS A2-6]

Through-spindle hole diameter mm (in.) 61 (2.4)[73 (2.9)]

Min. spindle indexing increment 0.0001

Spindle bearing inner diameter mm (in.) 100 (3.9) [110 (4.3)]

Spindle torque (40%ED/30min./cont) Nm (ftlbf) 223/172/158 (164.5/126.9/116.5)


Allowable rotational speed min-1 - 1,000

Bearing I.D. mm (in.) - 70 (2.7)

Tool spindle(Turret 1)

Number of tool stations 1

Min. B-axis indexing increment 0.0001

Max. tool spindle speed min-1 12,000 [20,000]Taper hole of rotary tool spindle Capto C5[HSK-A50(T50)]Inner diameter of rotary Tool spindle bearing mm (in.) 65 (2.5)Tool storage capacity 38 [76]

Max. tool diameterWith adjacent tools mm (in.) 70 (2.7)Without adjacent tools mm (in.) 130 (5.1)

Max. tool length mm (in.) 250 (9.8) /210 (8.2) Max. tool mass kg (lb.) 5 (11.0)

Max. tool mass moment (from spindle gauge line) Nm (ftlbf)3.9 (2.9)

Tool changing time (Tool-to-tool) sec. 1.2

Spindle torque (15%ED/25%ED/cont) Nm (ftlbf) 49/37/22 (36.1/27.3/16.2)

Turret 2

Number of tool stations - 10

Turret indexing time (1-station) sec. - 0.19

Shank height for square tool mm (in.) - 20 (0.8)

Shank diameter for boring bar mm (in.) - Max. 32 (1.2)Max. rotary tool spindle speed min-1 - 6,000

Spindle torque (15%ED/cont) Nm (ftlbf) - 4.8/2.3 (3.5/1.7)

Tailstock

Tailstock spindle diameter mm (in.) - 90 (3.5) -

Taper hole of tailstock spindle -Live center

[Built-in center ]-

Tailstock travel mm (in.) - 815 (32.1) -

Feedrate Rapid traverse ratemm/min

(ipm)

Tool spindleX, Y: 40,000 (1,574.8)Z: 50,000 (1,968.5)

Tool spindleX, Y: 40,000 (1,574.8)Z: 50,000 (1,968.5)

Workpiece discharge unitA:36,000 (1,417.3)

Tool spindleX, Y: 40,000 (1,574.8) Z: 50,000 (1,968.5)

Workpiece discharge unitA:36,000 (1,417.3)

Turret 2X2, Z2: 30,000 (1,181.1)

min-1 B: 100 C: 250

MotorsMotor for Spindle 1 (40%ED/30 min./cont) kW (HP) 11/11/7.5 (15/15/10)

Tool spindle drive motor (25%ED/cont) kW (HP) 9/5.5 (12.0/7.5)

Turret 2 rotary tool spindle drive motor (15%ED/cont) kW (HP) - 1.5/1.2 (2/1.6)

Power sources(Standard)

Electrical power supply (cont) kVA 34.03 40.64 42.21

Compressed air supply MPa (psi), L/min (gpm) 0.5 (72.5)450 (118.8) Tank capacity Coolant tank capacity L (gal) 300 (79.2)

Machine sizeMachine height mm (in.) 2,412 (95.0)

Floor space (WidthDepth) mm (in.) 2,4242,710 (95.4106.7)

Mass of machine kg (lb.) 8,450 (18,590) 8,950 (19,690) 9,250 (20,350)

[ ] Option For 65 mm (2.5 in.) bar work capacity specifications Bar work capacity: Depending on the chuck/cylinder used and its restrictions, it may not be possible to reach full bar work capacity. Max. spindle speed: Depending on restrictions imposed by the workpiece clamping device, fixture and tool used, it may not be possible to rotate at the maximum spindle speed. Please use a dual contact tool when using a No. 40 taper spindle at 15,000 min-1 or higher. ANR: ANR refers to a standard atmospheric state; i.e., temperature at 20C (68F); absolute pressure at 101.3 kPa (14.7 psi); and relative humidity at 65%. Power sources, Machine size: the actual values may differ from those specified in the catalogue, depending on the optional features and peripheral equipment. Compressed air supply: Please be sure to supply clean compressed air . A criterion capacity to select a compressor is 90 L/min (23.8 gpm) per 0.75 kW (1 HP).However, this figure may differ depending on the type of compressors and options attached. For details, please check the compressor specifications.

When the tool tip air blow is regularly used, air supply of more than 300 L/min (79.2 gpm) is separately required. The information in this catalog is valid as of October 2010.

NT1000100215

21NTX1000/NTX2000

ItemNTX1000

S SZ SZM

Capacity

Max. swing of workpiece mm (in.) 370 (14.5)Swing over cross slide mm (in.) 370 (14.5) 370 (14.5) Max. turning diameter mm (in.) 370 (14.5) 370 (14.5)Max. turning length mm (in.) 424 (16.6)

Bar work capacity mm (in.) 52 (2.0) [65 (2.5)]

Travel



Z-axis (Tool spindle) mm (in.) 460+155 (18.1+6.1)

B-axis (Tool spindle) 120

(X2-axis (Turret 2)) mm (in.) - 155 (6.1)(Z2-axis (Turret 2)) mm (in.) - 610 (24.0)BW-axis 4 positioning angles

Spindle 1

Max. spindle speed min-1 6,000[5,000]


Spindle nose JIS A2-5[JIS A2-6]

Through-spindle hole diameter mm (in.) 61 (2.4)[73 (2.9)]


Spindle bearing inner diameter mm (in.) 100 (3.9) [110 (4.3)]

Spindle torque (40%ED/30min./cot) Nm (ftlbf) 223/172/158 (164.5/126.9/116.5)

Spindle 2

Max. spindle speed min-1 6,000


Spindle nose 80 (3.1) g6 flat noseThrough-spindle hole diameter mm (in.) 38 (1.5)Min. spindle indexing increment 0.0001

Spindle bearing inner diameter mm (in.) 70 (2.7)Spindle torque (25%ED/cont) Nm (ftlbf) 37/22 (27.3/16.2)




Max. tool spindle speed min-1 12,000 [20,000]

Taper hole of rotary tool spindle Capto C5 [HSK-A50 (T50)]

Inner diameter of rotary Tool spindle bearing mm (in.) 65 (2.5)Tool storage capacity 38 [76]

Max. tool diameterWith adjacent tools mm (in.) 70 (2.7)Without adjacent tools mm (in.) 130 (5.1)

Max. tool length mm (in.) 250 (9.8) /210 (8.2) Max. tool mass kg (lb.) 5 (11.0)

Max. tool mass moment (from spindle gauge line) Nm (ftlbf)3.9 (2.9)


Spindle torque (15%ED/25%ED/cont) Nm (ftlbf) 49/37/22 (36.1/27.3/16.2)

Turret 2

Number of tool stations - 10Turret indexing time (1-station) sec. - 0.19Shank height for square tool mm (in.) - 20 (0.8)Shank diameter for boring bar mm (in.) - Max. 32 (1.2)Max. rotary tool spindle speed min-1 - 6,000Spindle torque (15%ED/cont) Nm (ftlbf) - 4.8/2.3 (3.5/1.7)


(ipm)

Tool spindleX, Y: 40,000 (1,574.8)Z: 50,000 (1,968.5)

Spindle 2A: 36,000 (1,417.3)

Tool spindleX, Y: 40,000 (1,574.8) Z: 50,000 (1,968.5)

Turret 2X2, Z2: 30,000 (1,181.1)

Spindle 2A: 36,000 (1,417.3)

min-1 B: 100 C: 250

Motors

Motor for Spindle 1 (40%ED/30 min./cont) kW (HP) 11/11/7.5 (15/15/10)

Spindle 2 drive motor (25%ED/cont) kW (HP) 7.5/5.5 (10/7.5)

Tool spindle drive motor (25%ED/cont) kW (HP) 9/5.5 (12.0/7.5)



Electrical power supply (cont) kVA 40.34 44.56 47.14

Compressed air supply MPa (psi), L/min (gpm) 0.5 (72.5)450 (118.8) Tank capacity Coolant tank capacity L (gal) 300 (79.2)

Machine sizeMachine height mm (in.) 2,412 (95.0)


Mass of machine kg (lb.) 8,450 (18,590) 8,950 (19,690) 9,250 (20,350)

[ ] Option For 65 mm (2.5 in.) bar work capacity specifications Bar work capacity: Depending on the chuck/cylinder used and its restrictions, it may not be possible to reach full bar work capacity. Max. spindle speed: Depending on restrictions imposed by the workpiece clamping device, fixture and tool used, it may not be possible to rotate at the maximum spindle speed. Please use a dual contact tool when using a No. 40 taper spindle at 15,000 min-1 or higher. ANR: ANR refers to a standard atmospheric state; i.e., temperature at 20C (68F); absolute pressure at 101.3 kPa (14.7 psi); and relative humidity at 65%. Power sources, Machine size: the actual values may differ from those specified in the catalogue, depending on the optional features and peripheral equipment. Compressed air supply: Please be sure to supply clean compressed air . A criterion capacity to select a compressor is 90 L/min (23.8 gpm) per 0.75 kW (1 HP).However, this figure may differ depending on the type of compressors and options attached. For details, please check the compressor specifications.


NT1000100215

22 NTX1000/NTX2000

Specifications

Machine specificationsItem

NTX2000T TZ TZM

Capacity

Max. swing of workpiece mm (in.) 660 (25.9)

Swing over cross slide mm (in.) 660 (25.9) [Turret 2 300 (11.8)]

Max. turning diameter mm (in.) 610 (24.0) [Turret 2 270 (10.6)]

Max. turning length mm (in.) 1,540 (60.6)

Bar work capacity mm (in.) 65 (2.5)

Travel



Z-axis (Tool spindle) mm (in.) 1,560 (61.4)

(X2-axis (Turret 2)) mm (in.) 160 (6.3)

(Z-axis (Turret 2)) mm (in.) 1,402 (55.2)

Spindle 1



Spindle nose A2-6

Through-spindle hole diameter mm (in.) 73 (2.9)


Spindle bearing inner diameter mm (in.) 120 (4.7)

Spindle torque (15%ED/30 min./cont) Nm (ftlbf) 230/178/159 (169.6/131.3/117.3)




Max. tool spindle speed min-1 12,000

Taper hole of rotary tool spindle BT40 [Capto C6] [HSK-A63]

Inner diameter of rotary Tool spindle bearing mm (in.) 70 (2.8)

Tool storage capacity 38 [76]

Max. tool diameterWith adjacent tools mm (in.) 70 (2.7)

Without adjacent tools mm (in.) 125 (4.9)

Max. tool length mm (in.) 300 (11.8)

Max. tool mass kg (lb.) 8 (17.6) [10 (22)]


Spindle torque (10%ED/cont) Nm (ftlbf) 120/44 (88.5/32.5)

Turret 2




Shank diameter for boring bar mm (in.) - Max. 32 (1.2)

Max. rotary tool spindle speed min-1 - 6,000


Tailstock

Tailstock spindle diameter mm (in.) 110 (4.3)

Taper hole of tailstock spindle Live center (MT5) [Built-in center (MT4)]

Tailstock travel mm (in.) 1,500 (59.1)


(ipm)Tool spindle

X, Y, Z: 40,000 (1,574.8)

Tool spindleX, Y, Z: 40,000 (1,574.8)

Turret 2X2: 30,000 (1,181.1)Z2: 38,000 (1,496.1)

Motors

Motor for Spindle 1 (30 min./cont) kW (HP) 22/18.5 (30/24.7)

Tool spindle drive motor (10 min./cont) kW (HP) 18.5/11 (24.7/15)



Electrical power supply (cont) kVA 50.2 56.8

Compressed air supply MPa (psi), L/min (gpm) 0.5 (72.5)450 (118.8)

Tank capacity Coolant tank capacity L (gal) 650 (171.6)

Machine size

Machine height mm (in.) 2,626 (103.4)


Mass of machine kg (lb.) 15,000 (33,000)

[ ] OptionFor when B-axis is at 90 position Bar work capacity: Depending on the chuck/cylinder used and its restrictions, it may not be possible to reach full bar work capacity. Max. spindle speed: Depending on restrictions imposed by the workpiece clamping device, fixture and tool used, it may not be possible to rotate at the maximum spindle speed. ANR: ANR refers to a standard atmospheric state; i.e., temperature at 20C (68F); absolute pressure at 101.3 kPa (14.7 psi); and relative humidity at 65%. Power sources, Machine size: the actual values may differ from those specified in the catalogue, depending on the optional features and peripheral equipment. Compressed air supply: Please be sure to supply clean compressed air . A criterion capacity to select a compressor is 90 L/min (23.8 gpm) per 0.75 kW (1 HP).However, this figure may differ depending on the type of compressors and options attached. For details, please check the compressor specifications.


23NTX1000/NTX2000

ItemNTX2000

S SZ SZM

Capacity

Max. swing of workpiece mm (in.) 660 (25.9)

Swing over cross slide mm (in.) 660 (25.9) [Turret 2 300 (11.8)]

Max. turning diameter mm (in.) 610 (24.0) [Turret 2 270 (10.6)]

Max. turning length mm (in.) 1,540 (60.6)

Bar work capacity mm (in.) 65 (2.5)

Travel



Z-axis (Tool spindle) mm (in.) 1,560 (61.4)

(X2-axis (Turret 2)) mm (in.) 160 (6.3)

(Z2-axis (Turret 2)) mm (in.) 1,402 (55.2)

Spindle 1



Spindle nose A2-6





Spindle 2



Spindle nose A2-6








Max. tool spindle speed min-1 12,000

Taper hole of rotary tool spindle BT40 [Capto C6] [HSK-A63]

Inner diameter of rotary Tool spindle bearing mm (in.) 70 (2.8)

Tool storage capacity 38 [76]

Max. tool diameterWith adjacent tools mm (in.) 70 (2.7)

Without adjacent tools mm (in.) 125 (4.9)

Max. tool length mm (in.) 300 (11.8)

Max. tool mass kg (lb.) 8 (17.6) [10 (22)]


Spindle torque (10%ED/cont) Nm (ftlbf) 120/44 (88.5/32.5)

Turret 2




Shank diameter for boring bar mm (in.) - Max. 32 (1.2)

Max. rotary tool spindle speed min-1 - 6,000



(ipm)

Tool spindleX, Y, Z: 40,000 (1,574.8)

Spindle 2A: 30 (1.2)

Tool spindleX, Y, Z: 40,000 (1,574.8)

Turret 2X2: 30,000 (1,181.1)Z2: 38,000 (1,496.1)

Spindle 2A: 30 (1.2)

Motors

Motor for Spindle 1 (30 min./cont) mm (in.) 22/18.5 (30/24.7)

Spindle 2 drive motor (30 min./cont) mm (in.) 22/18.5 (30/24.7)

Tool spindle drive motor (10 min./cont) mm (in.) 18.5/11 (24.7/15)

Turret 2 rotary tool spindle drive motor (15%ED/cont) mm (in.) - 1.5/1.2 (2/1.6)


Electrical power supply (cont) kVA 73.4 80.7

Compressed air supply MPa (psi), L/min (gpm) 0.5 (72.5)450 (118.8)

Tank capacity Coolant tank capacity L (gal) 650 (171.6)

Machine size

Machine height mm (in.) 2,626 (103.4)


Mass of machine kg (lb.) 15,000 (33,000)

[ ] OptionFor when B-axis is at 90 position Bar work capacity: Depending on the chuck/cylinder used and its restrictions, it may not be possible to reach full bar work capacity. Max. spindle speed: Depending on restrictions imposed by the workpiece clamping device, fixture and tool used, it may not be possible to rotate at the maximum spindle speed. ANR: ANR refers to a standard atmospheric state; i.e., temperature at 20C (68F); absolute pressure at 101.3 kPa (14.7 psi); and relative humidity at 65%. Power sources, Machine size: the actual values may differ from those specified in the catalogue, depending on the optional features and peripheral equipment. Compressed air supply: Please be sure to supply clean compressed air . A criterion capacity to select a compressor is 90 L/min (23.8 gpm) per 0.75 kW (1 HP).However, this figure may differ depending on the type of compressors and options attached. For details, please check the compressor specifications.


EXPORTATION: All contracts are subject to export permit by the Government of Japan. Customer shall comply with the laws and regulations of the exporting country governing the exportation or re-exportation of the Equipment, including but not limited to the Export Administration Regulations. The Equipment is subject to export restrictions imposed by Japan and other exporting countries and the Customer will not export or permit the export of the Equipment anywhere outside the exporting country without proper government authorization. To prevent the illegal diversion of the Equipment to individuals or nations that threaten international security, it may include a Relocation Machine Security Function that automatically disables the Equipment if it is moved following installation. If the Equipment is so-disabled, it can only be re-enabled by contacting Mori Seiki or its distributor representative. Mori Seiki and its distributor representative may refuse to re-enable the Equipment if it determines that doing so would be an unauthorized export of technology or otherwise violates applicable export restrictions. Mori Seiki and its distributor representative shall have no obligation to re-enable such Equipment. Mori Seiki and its distributor representative shall have no liability (including for lost profits or business interruption or under the limited service warranty included herein) as a result of the Equipment being disabled.

DCG, DDM, BMT and ORC are trademarks or registered trademarks of Mori Seiki Co., Ltd. in Japan, the USA and other countries. If you have any questions regarding the content, contact your nearest Mori Seiki distributor or Technical Center. The information in this catalog is valid as of October 2010. Designs and specifications are subject to changes without notice. Mori Seiki is not responsible for differences between the information in the catalog and the actual machine.

2-year warranty, twice the peace of mind. Subject to limitations, Mori Seiki machines ordered after April 1, 2007 now have a 2-year warranty. Please contact your sales representative for details.

For machines delivered outside of Japan, parts relating to machine breakdown will be guaranteed free for 2 years from the date of installation, and labor costs to repair will be free for 1 year.

NTX1020-EA01-1VV.1010.CDT.0000Created in Japan

Documents

Ntx 1020