OBSERVATIONAL SCIENCES (ARIES) S. T. …...For all earth & sand supplied for filling from outside deduction of 20% voids shall be made. 5. Necessary shoring & strutting of original

ARYABHATTA RESEARCH INSTITUTE OF OBSERVATIONAL SCIENCES (ARIES) PROPOSED S. T. RADAR BUILDING AT NAINITAL

Page 1 of 83


Page 2 of 83

ARYABHATTA RESEARCH INSTITUTE OF OBSERVATIONAL SCIENCES

(ARIES)

GRAND SUMMARY

(CONSTRUCTION OF S.T. RADAR BUILDING AT NAINITAL)

S.NO ITEM PART AMOUNT 1. CIVIL WORKS I 2. ELECTRICAL WORKS II 3. AIRCONDITIONING WORKS III 4. FIRE SAFETY WORKS IV GRAND TOTAL


Page 3 of 83

ARYABHATTA RESEARCH INSTITUTE OF OBSERVATIONAL SCIENCES (ARIES)

SUMMARY OF PART -1

(CONSTRUCTION OF S.T. RADAR BUILDING AT NAINITAL)

S.NO Description Amount (Rs) A. EARTH WORK. B. CONCREATING (PCC & RCC) WORK. C. M.S REINFORCEMENT WORK. D. CENTERING & SHUTTERING WORK. E. MASONARY WORK. F DAMP PROOFING WORK. G. PLASTERING AND POINTING WORK. H. DOORS & WINDOWS WORK. I. STEEL AND IRON WORK. J. WATER PROOFING WORK. K. FLOORING AND PAVING WORK. L. POP & PAINT WORK. M. INTERNAL WATER SUPPLY WORK. N. PLUMBING AND SANTATION. O. MISCELLANEOUS. TOTAL Rs.

TOTAL AMOUNT IN WORD (Rs._______________________________________________________)


Page 4 of 83

(A) EARTH WORK SOR. No Description Qty Unit Rate (Rs.) Amount (Rs)

A-1 Earth work in Excavation in all types of soil, site leveling including morrum for foundations of wall, column, equipment support foundation, plinth beams, basement; trenches, underground sumps etc. including, shoring, strutting, bailing out water Pumping off water if required, refilling the foundation pits, trenches Ramming, watering and consolidation Including disposal of surplus excavated earth. Lead up to 100m disposed earth to be leveled and neatly dressed, stacking in the plot or spreading in low lying areas or as directed by Site-In-Charge. From existing ground level to 1.5m Depth

579.95

Cum

A-1.1

- Do- as item No. A-1 but in ordinary Rock.

193.60

Cum

A-1.2

-Do- as Item No. A-1 but in Hard Rock (blasting prohibited)

96.87

Cum

A-1.3

-Do- as in item no A-1 but for depth exceeding 1.50mt. but not exceeding 3.00 mt. as directed by site-in-charge. (Rate is over corresponding basic item for depth up to 1.50 mt.)

115.99

Cum

A-2 Filling in plinth or in ground other than plinth for land developments with available excavated soil (excluding rock) including spreading soil in layers of not exceed 200 mm thick; watering and consolidating each

430.42

Cum


Page 5 of 83

layer by ramming including plate compactors etc. complete as directed, including cost of transportation for all leads and lifts.

A-3

Supplying & filling in with outside earth without lumps, stone in under floors, plinth trenches or wherever required including, Watering, ramming consolidating and dressing complete as directed by site-in-charge.

210.00 Cum

A-3.1

DO as item no A-3 but with river sand

60.00 Cum

A-4 Providing pre-construction Anti Termite treatment as per the specification of pest control of India or any other approved agency, to the satisfaction as directed by site-in-charge. (Contractor shall furnish a guarantee for 5 years from date of treatment against any sub terrain an pest infestation.)

1357.08

Cum

Total Cost of Earth work = Notes :- 1. Lead for shifting of all excavated material 300 meters, beyond building line. 2. For excavation of disintegrated rock and hard rock measurement should be as per stack with 50% deductions for voids. 3. Filling includes watering ramming & consolidation as required. 4. For all earth & sand supplied for filling from outside deduction of 20% voids shall be made. 5. Necessary shoring & strutting of original earth as well as filled up earth to be done in order to avoid collapses, without any additional cost.


Page 6 of 83

(B) CONCREATING WORK

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) B-1

Providing and laying in position cement concrete with 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) including the cost of centering and shuttering, ramming, consolidating etc as required including ,all labor, material and T & P etc. complete as directed by the Site -In-Charge, for all work below or above plinth level, encasing W.W & S.W pipes, floor channels, Manholes, at any height & in pavements or roads.

164.21

Cum

B-2

Do as in B-1 but with 1:2:4 (1 cement:2 coarse sand : 4 graded stone aggregate 20mm nominal size).

54.45

Cum

B-3 Providing and laying machine mixed and machine vibrated in situ M-20 cement concrete using 1:1.5:3 (1 cement :1.5 coarse sand : 3 parts of graded stone aggregates 20mm nominal size) for RCC structural elements up to plinth in all shapes & forms including foundations, columns, floor slab, projections with drip moulds, staircases, mullions, ledges, sills, Retaining walls, Column foundations, Tie Beams in foundation, trenches, slabs drainage chambers in any shape including circular as per drawings & design, for all lifts; including bailing out water;

275.57 Cum


Page 7 of 83

Total Cost of Concrete work Rs.=

compaction, curing and roughening the surface if special finish is to be provided excluding reinforcement, without cost of centering and shuttering complete as directed by Site-In-Charge.

B-4

DO as in B-3 but M-20 with 1:1.1/2:3 (1 cement :1.1/2 coarse sand : 3 parts of stone graded stone aggregates 20mm nominal size) in superstructure or as required up to any heights

404.89 Cum

B-5

Do as item no B-3 but M-25 with 1:1:2 (1 Cement : 1 coarse sand : 2 graded stone aggregate 20 mm nominal size) in super structure or as required up to any height

173.52 Cum

B-6 Providing and laying pre cast cement concrete slab for trench cover, pit cover, shelves, ledges 35mm to 150mm thick as per drawings, using 1:2:4 concrete (1Cement: 2 coarse sand: 4 graded stone aggregate 20 mm nominal size), hoisted and fixed in position including necessary formworks, hooks, grooves, inserts, projections, lifting hooks, grouting and pointing the joints finishing neat complete excluding reinforcement (centering and shuttering inclusive ) but including exposed concrete finish for all visible surface

5.60 Cum


Page 8 of 83

Notes:- 1. All RCC shall be M20 for works below plinth & M25 above plinth grade unless noted otherwise. 2. MS TOR/ TMT Reinforcement in RCC to be paid separately unless otherwise specified. 3. The column and beam size mentioned on tender drawings are indicative, and for any change in size either on higher or lower side, does not entitle the contactor to ask for any additional payment towards the change of whatsoever nature. 4. Cover blocks for reinforcement must be in CM 1:3 (1 cement:3 coarse sand) mortar and thickness must be as per drawing (Cover blocks must be well cured)

5. Curing to all concrete must be done for at least 15 days unless specified otherwise. 6. Test cube should be cast as per the instruction given in detailed specification. 100% payment

towards respective item will not be made till the test results are obtained. 7. If required dewatering shall be done without any extra cost while casting concrete in foundations. 8. All the structural concrete M20 and above grades shall be machine batched, machine mixed and

machine vibrated design mix. 9. Binding wire(18 gauge MS) must be annealed. 10. For tying reinforcement bars greater than 20mm dia. Two wire pieces should be used. 11. If required welding should be done in addition to binding for lapping the bars in beams,

columns etc. as instructed.


Page 9 of 83

(C) REINFORCEMENT WORK

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) C-1

Providing & Fixing MS Reinforcement with TMT for R.C.C work including straightening , cutting, bending placing in position and binding with 18mm gauge MS wire(To be supplied by contractor at his own cost) & welding if required or directed by Site-In-Charge. All complete nothing extra payable for margins & wastages.

99010.38 Kg

Total Cost of Reinforcement work Rs.= Notes – 1. Nothing extra payable for welding the bars in addition to binding with wires if required.


Page 10 of 83

(D) CENTERING & SHUTTERING WORK

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) D Centering and shuttering

including strutting, propping etc. and removal of form for :

D-1 Centering and shuttering works for concrete elements, vertical, horizontal or inclined in all shapes including circulars, drip courses as per drawings at any levels below Plinth including necessary scaffolding as directed by Site- In-Charge .

561.72

Sqm

D-2

Do as D-1 but for works above plinth up to highest level .

1552.70 Sqm

D-3 New plywood shuttering in 12mm thick commercial water proof ply for slab & beams or wherever required at any level or height including strutting, propping etc. and removal of form for all labor, material and T&P etc. Complete as per direction of Site-In-Charge.

1153.00 Sqm

Total Cost of Shuttering & Centering Rs. = Notes:-

1. Top slab containing pedestals/antennae to be casted on brand new water proof commercial ply only, on which grid should be marked properly to achieve the accuracy up to 3mm between subsequent antennae. 2. Oiling/greasing must for all shuttering elements in order to achieve smooth finish, nothing

extra payable for this.


Page 11 of 83

(E) MASONRY

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) E-1 Providing and constructing 1st

class Brick masonry for all shapes including circular of any thickness in cement mortar 1:6 (1cement: 6 coarse sand) with brick having minimum crushing strength of 75 Kg /sq. cm. including scaffolding; racking out of the joints; curing etc. complete at all levels in sub -structure.

80.56

Cum.

E-2 -DO- as item no E-1 but in superstructure at all heights above plinth level.

452.99 Cum

E-3 Providing and constructing 1st class half brick masonry in cement mortar 1:4 (1cement :4 coarse sand) in partition walls & providing & placing 2 Nos 6 mm dia M/S bars at every fourth course or 25 mm x 1.2 mm iron hoop in every third course, with brick having minimum crushing strength of 75 Kg /sq.cm including scaffolding, Racking out of the joints in as directed by Site-In-Charge (Rates inclusive of MS bars &/ or iron hoops)

59.20 Sqm


Page 12 of 83

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) E-4 Providing & laying a coarse of

Random Rubble masonry with hard stone in works at all heights & in retaining walls or where ever required including leveling with cement concrete 1:4:8 (1 Cement:4 Coarse Sand:8 graded stone 20 mm nominal size ) as directed by Site-In-Charge complete with provision beep holes etc.

570.75 Cum

Total Cost of Masonry work Rs.= Note:- 1. All brick to be thoroughly soaked in water before start of work. 2. Screened sand should be used for all brick work. 3. Coarse sand shall be used in mortars unless otherwise specified. 4. All joints should be raked before closure of day work or simultaneously during the course of work. 5. Care to taken to provide RCC band in half brick thick wall as instructed & specified. 6. All joints in masonry should be well staggered. 7. Proper shuttering must be provided for concrete coping at all locations. 8. Foundation trenches should be dewatered if required during construction of foundation masonry at no extra cost. 9. Holes and pockets in brick work for rainwater pipes and other pipes shall be kept or pipe shall be provided at the time of raising of the masonry. Nothing extra shall be paid for this.


Page 13 of 83

(F) DAMP PROOF COURSE

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) F-1 Providing and Laying damp-

proof Course 40 mm thick with cement concrete 1:2:4 (1 cement:2 concrete:4 graded stone aggregate 12.5 mm nominal size). Including necessary centering, shuttering & curing etc complete

80.52 Sqm.

F-2 Supply and mixing water proofing material in cement concrete / cement mortar work @ 1 Kg per 50 Kg of cement.

10.00 Kg.

F-3 Providing & Applying a coat of residual petroleum bitumen of penetration 80/100 of approved quality using 1.7 kg per square meter on damp proof course after cleaning the surface with brushes and finally with a piece of cloth lightly soaked in kerosene oil.

80.52 Sqm.

Total Cost of Damp Proof Course work = Notes – 1. Curing of at least 7 days must for DPC.


Page 14 of 83

(G) PLASTERING AND POINTING

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) G-1

Providing and applying 12mm thick finish cement plaster over surface of any shape including grooves at all heights on any side of wall in 1:4 cement (1 cement :4 sand) mortar for Bends, moulds, Walls, Beams, Column, where ever required including scaffolding curing and finishing smooth complete as directed by Site- In-Charge.

2017.79 Sqm

G-2 Providing and applying 6mm thick cement plaster over Ceiling, Stairs, & Stair Ceiling, soffits at all heights using 1:3 (1cement :3 sand ) mix including finishing smooth, scaffolding curing etc complete to the satisfaction of Site-In-Charge.

2221.08 Sqm

G-3 Extra for applying neat cement finish @ 2.2Kg per square meter to the plastered surface and or concrete drains while the concrete is still green.

61.50 Sqm

G-4

Providing and applying 15mm thick cement plaster on the rough side of single or half wall at all heights in 1:4 cement mortar (1Cement: 4 Sand) with smooth finish with scaffolding & curing etc complete for rough side of masonry as directed by Site-In-Charge.

1985.00 Sq.m


Page 15 of 83

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) G-5

Providing and fixing 24gauge chicken wire mesh at a junction of masonry work and RCC work or on any other place as directed including fixing with nails rawl plugs etc. complete at all heights, before applying plaster.

162.00 Sqm

G-6 Efflorescence treatment for exposed surfaces by painting with two coats of 15% Calcium chloride at 2 hours interval & than allowed to dry for at least 24 hours before commencing plaster, up to the satisfaction of Site-In-Charge complete with all materials labour & T&P etc.

6223.00

Sqm

Total Cost of Plastering & Pointing work Rs.= Note:-

1. For every window, window, chhajja, canopy, doors etc. which is on external side drip mould or groove of width 40mm and thick of 6mm or respectively as directed in the plaster should be provided for which nothing extra payable.

2. Before commencing the plaster all the surface must be made thoroughly wet preferably on previous day.

3. Grooves patta, moulding in any type of plaster to be finished neatly up to the satisfaction of site-in-charge.

4. Grooves with cement finish up to 12mm x 6mm shall be formed in plaster at junction of slab and beam & slab and brick work with no extra cost. Similar groove shall be made in plaster at the junction of masonry and wood, steel door and window frame, or at the bottom of beam as drip mould with no extra cost.

5. The sand used shall be 50% fine and 50% coarse for the plaster unless specified otherwise.


Page 16 of 83

(H) DOORS & WINDOWS WORK

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) H-1

Providing and fixing aluminum sections for doors, windows, ventilators and partitions with extruded built up standard powder coated (Min thickness of coating 50 Micron) tubular sections/ appropriate sections and other sections of approved type, Fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up to gap at junction, at top, bottom and sides with Polysulphate / silicon sealant, required EPDM/ Neoprene felt glazing gasket etc. Aluminum section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat angle, Aluminum snap beading for glazing / paneling, C.P brass / stainless steel screws, handles, tower bolts, locking arrangements all complete with glazing 5.5 mm plain glass duly fixed & as per architectural drawings and the directions of Site-in-charge.

H-1.1

For windows & Ventilators Polyester powder coated aluminum (minimum thickness of polyester powder coating 50 micron) sliding type containing fixed frames 75mmx26mmx 1.56mm with three shutters two with glazing & one with SS

120.00 Sqm


Page 17 of 83

mosquito mesh provision of frame 15mm x 40mmx 1mm as per architectural drawings & up to the satisfaction of Site-In-Charge.

H-1.2 For doors complete with frames 63.5mmx38mmx2.50mm & shutters with side rails 50mmx44.50mmx 1.90mm & top, middle & bottom rails 100mmx44.5mmx2.50mm Polyester powder coated aluminum (minimum thickness of polyester powder coating 50 micron) complete as per architectural drawings & to the satisfaction of Site-In-Charge.

a. For partially glazed with 5.5 mm plain glass & partially paneled with 12mm Novapan laminated from both sides.

b. Fully glazed with 5.5 mm plain glass.

24.96

24.00

Sqm

Sqm

H-2 Providing and fixing Structural Glazing extruded built up standard tubular sections/ appropriate sections and other sections of approved type. Fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up to gap at junction, at top, bottom and sides with Polysulphate / silicon sealant, Teflon tape etc required. Aluminum section shall be smooth, rust free, straight, mitered and jointed mechanically wherever required including cleat

58.00

Sqm


Page 18 of 83

angle, Aluminum snap beading for glazing / paneling, C.P brass/ stainless steel screws, all complete with glazing 5.5 mm plain glass duly fixed & as per architectural drawings and the directions of Site-In-Charge

H-2.1

Extra for heat reflective glass 5.5 over & above plain glass of desired shade complete with fixing etc up to the satisfaction of Site-In-charge.

58.00 Sqm

H-3 Fully glazed doors in 12mm thick toughened glass on pivot & hinges arrangements complete with Chrome finished handles of desired shape & size and all accessories as required for proper completion of work to the satisfaction of Site-In-Charge.

7.0

Sqm

H-4 Providing & fixing hydraulic door closure of approved gauge complete with steel screws & other items as required up to the satisfaction of Site-In-Charge.

10 No’s

H-5

Providing & fixing double action hydraulic floor spring of approved brand and manufacture for doors including cost of cutting floors as required. Embedding in floors and cover plates with brass with brass pivot and single piece M.S sheet outer box with slide plate &Stainless steel cover plate etc. complete as per the direction of Site-In-charge.

15 No’s

H-6 Providing & fixing pre approved chromium plated brass 100 mm Mortice latch & lock with six

8

Nos


Page 19 of 83

pairs of levers & a pair of lever handles with necessary screws etc complete to the satisfaction of Site-In-Charge

H-7 Providing & fixing wood work in of doors, windows & other frames in 65x125mm Sal wood frames including 6 Nos Holdfast 125x25x6 mm, anodized steel screws, a coat of anti termite solution, bed blocks in cement concrete 1:2:4 of desired size and other necessary item as required for proper completion of work as per Architectural drawings framed and fixed in position & to the satisfaction of Site-In-Charge

0.95 Cum

H-8 Providing & fixing 35mm thick ISI marked flush door shutters decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters, Teak wood lipping 35x5 including steel but hinges with necessary screws, steel tower bolts, handles with locking arrangements as per Architectural drawings framed and fixed in position & to the satisfaction of site-in-charge. (Lipping & veneering inclusive of rates)

28.80 Sqm

Total Cost of Aluminum & Wood work =


Page 20 of 83

Notes:-

1. All aluminum section/accessories shall be pre-approved for gauges, sizes & finish from Site -In- charge before fabrication/ commencement of work.

2. Sal wood Chaukats should be ready size as per drawing no margins allowed. 3. For wood work rates should be inclusive of veneering of desired shade & grain where ever

Required or mentioned. 4. For all aluminium/ wood doors Fittings i.e Steel hinges, Tower bolts, Handles, Handles

with locking arrangements, Door stoppers all of desired shape & finish should be included in rates. Nothing extra payable for same.


Page 21 of 83

(I) STEEL AND IRON WORK

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs)

I-1 Providing and fixing in position MS Foundation bolts at all heights including Nuts, Bolts, Washers bolts threaded for the portion of 100- 150 mm , positioning and casting along with the concrete necessary templates for positioning bolts, centering, curing etc. Complete as directed by Site-In-Charge.

250.40 Kg.

I-2 Providing and fixing in position M.S Inserts of Columns, Roof slabs, Retaining wall, Tie Beams, Plates, Flat, Tees, Grills & Gratings with provision for supports hangers, brackets, frame around cutouts, MS Pipes, Sleeves etc in true line and level including embedding of the same in permanent works at the time of casting of RCC works with necessary welding or fixing / welding with existing new RCC / brickwork /MS work including chipping finishing curing grinding and painting of one coat red oxide and two coats of approved make synthetic enamel paint. Complete as directed by Site-In-Charge.

110.00 Kg.

I-3 Providing & fixing in position collapsible steel shutters with vertical channel 20x10x2mm and braced with flat iron diagonals 20x5mm size with top and

33.00 Sqm


Page 22 of 83

bottom rail of T-iron 40x40x6mm with 40mm dia, steel pulleys complete with Bolts, Nuts, Locking arrangement, stoppers, handles including applying a priming coat of approved steel primer & 2 coat of Enamel Paint complete as directed by Site-In-Charge.

I-4 Providing and fixing in position at any level S.S railing in 16 gauge of desired shape & section As per drawing & design. With or without Hand Rail for Stair Case around openings and terrace, Heavy class with accessories and S.S pipe fittings holdfasts if any welding, grinding , polishing & Fixing with screws or appropriate anchor fastener. Bed blocks grouting in C.C. with 1:2:4 polishing etc required etc. Complete.

165.00 RM

I-5 Providing & fixing rolling shutters of approved make, made of required size M.S. laths interlocked together through their entire length and jointed together at the end by end locks mounted on specially designed pipe shaft with brackets, side guides and arrangements for inside and outside locking with push and pull operation complete including the cost of providing and fixing necessary 27.5 cm long wire springs grade No. 2 and M.S. top cover of required thickness for rolling shutters

20.20 Sqm.


Page 23 of 83

including a priming coat with red oxide & two coats of enamel paint.

I-6 Providing & fixing bended S.S steel pipe of 16 gauge & of 15mm internal dia in desired shape to enroot the R.F. cable through R.C.C slab including filling of opening with silicon sealant of 1st quality including all labor, material and T&P etc complete as directed by Site-In-Charge.

250.00 NOS.

I-7 Providing & fixing MS stands as per drawing & design in cleat Angels, MS Flats, MS Squares & MS Plates properly welded with fillet weld & fixed to surface with anodized steel screws all including fabrication fixing at desired place complete including Priming & Enamel Paints with all labor, material and T&P etc. complete as per architectural drawings & to the satisfaction of Site-In-Charge.

6848

Kg.

Total Cost of Steel & Iron work = Note:-

1. Threads of foundation bolt to be protected by applying grease and plastic paper. 2. Appropriate gauge must be given to the welders for measuring welding sizes. 3. If required as per the instructions of the Engineer pre-heating of the welding electrodes is to be done at no extra cost. 4. The surface of steel should be thoroughly cleaned before application of red oxide. (Water with 1% phosphoric acid can be used. If phosphoric acid is used, the surface should be washed and dried before application of red oxide. 5. Contractors have to make the shop drawing for structural steel work. These drawings

will have to be got approved from owner before releasing for fabrication / construction.


Page 24 of 83

(J) WATER PROOFING

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) J-1 Providing & laying integral

cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations A: applying a slurry coat of neat cement using 2.75 Kg/Sqm of cement admixed with water proofing compound approved by Site-In-Charge over RCC Slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. B. Laying brick bats with mortar using broken bricks/ brick bats 25 mm to 115 mm size with 50% of cement Mortar 1:4 (1 Cement: 4 Coarse sand) admixed with approved water proofing compound over 20 mm thick layer of cement mortar 1:4 admixed with water proofing compound to required slope & treating similarly the adjoining walls up to 300 mm height including rounding of junctions of walls & slabs. C. After 2 days of proper curing a second coat of cement slurry using 2.75 Kg/Sqm of cement admixed with water proofing compound. D. Finishing the surface with 20 mm thick joint less cement

992.61 Sqm


Page 25 of 83

mortar 1:4 (1 cement: 4 Coarse Sand) admixed with water proofing compound including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry & making pattern of 300x300 mm square 3 mm deep. E. The whole terrace so finished shall be flooded for a minimum period of two weeks for curing and for final test. Average thickness of 120 mm & at khurras 65 mm.

J-2 Making Khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 Cement: 2 Coarse sand: 4 Graded stone aggregate of 20 mm nominal size) over PVC sheet 1Mx1Mx 400 Micron, finished with 12 mm cement plaster 1:3 (1 Cement: 3 Coarse sand) & a coat of neat cement rounding the edge sand making & finishing outlet complete to the satisfaction of Site-In-charge.

6

Nos

J-3 Providing Gola 75x75mm in cement concrete 1:2:4 (1Cement: 2 Coarse sand: 4 graded stone aggregate 10 mm nominal size) including finishing with cement mortar 1:3 (1 cement : 3 Fine sand) complete to the satisfaction of Site-In-charge.

120.00

RM

Total Cost of Water Proofing work = 729624.60


Page 26 of 83

(K) FLOORING AND PAVINGS:

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) K-1 VITRIFIED TILES :-

10 mm thick Vitrified tiles flooring of first quality 600mm x 600mm in flooring & in skirting laid over 20 mm thick cement mortar 1:4 (1 cement & 4 Coarse sand) fixed with cement paste slurry finished with matching color grouted in joints with all labor and T&P etc. required for proper completion of work.

164.92

Sqm.

K-2 PCC FLOORING :- (A) Providing 40 mm thick Plain Cement Concrete floor 1:2:4 (1 cement: 2approved coarse sand: 4 graded approved stone 10 mm nominal size) single laid panels finished with 3 mm floating coat of neat cement as specified over it, and excluding 100 mm thick base concrete of uniform finish including supply of all materials labor and T&P etc. required for proper completion of the work.

824.63

SQM

K-3 (B)Providing & fixing fiber glass strips in joints of cement concrete floor with 40 mm wide and 4mm thick including all labor, material and T&P etc. compete & to the satisfaction of Site-In-Charge.

215.00 RM


Page 27 of 83

K-4 Providing & laying cement plaster skirting (up to 30 cm height) with cement mortar 1:3 (1 Cement:3 Coarse sand) finished with a floating coat of neat cement with 18mm thick including all labor, material and T&P etc. compete & to the satisfaction of Site-In-Charge.

124.00 SQM

K-5 CEREMIC GLAZED TILES:- Providing & fixing 1st quality Ceramic Glazed wall Tiles in Toilets Blocks walls up to required height of approved make in all colors & shade of any size as approved by Site-in-charge over 12mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand) and joining with pigmented cement slurry @ 3.3 kg. Per sqm. including pointing in white cement mixed with pigment of matching shade complete.

119.59

Sqm.

K-6 Providing & fixing 18mm thick Udaipur Green Marble Stone in Stair Case Risers / Tread, landing & in skirting over 20mm thick base cement mortar 1:4 (1 cement:4 course sand) laid & jointed with grey cement slurry and joint filled with suitable color pigment mixed in white cement including rubbing and granite polishing complete to the satisfaction of Site-In-Charge.

62.00 Sqm.

K-7 Extra for pre finished nosing to the Treads of steps of marble stone.

112.80 RM


Page 28 of 83

K-8 KOTA STONE FLOORING :- Providing & fixing Kota stone flooring & skirting 25 mm thick of size 450 x450 mm and above flooring over previously prepared base with 2 cm thick 1:3 cement & coarse sand mortar including filing of joints with cement mixed with pigment required for the matching the shade of floor as per direction of Site-In-Charge including cutting & granite polishing including supply of all materials T&P etc. required for proper completion work.

217.00 Sqm.

K-9 Concrete Pavers Flooring Works :- Providing & fixing M 20 high strength 75 mm thick in concrete Pavers of approved make shape design & color in mat finish over 2” leveled coarse sand bed & gaps duly filled with fine sand as directed by Site-In-Charge.

100.00

sqm

K-10

A.

B.

False Flooring Work :- Providing & fixing the raised flooring of Microtac Access Floor System with following Access floor tiles using high yield MS powder coated molded sheet with cementations in-fill tiles with edge trimmed, & with PVC edge beading having anti static properties. Top surface provided with 1.6mm pressure as per the manufacture specification. Finished False flooring system shall be designed to take the load of 1.2

832.75

sqm


Page 29 of 83

tons / sqm. Tile mounted on 300mm ht. high yield MS adjustable jack with necessary lateral supports with snap lock system. All MS section hot dip galvanized. Rates shall be inclusive of making openings/provisions of fixing structural steel frames to be supplied by ARIES.

K-11 Anti Skid Ceramic Tiles : Providing & laying Anti Skid Ceramic glazed floor tiles 300 x 300 mm (Thickness & type specified by the manufacture) of 1st. quality confirming to approved make in desired color such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse sand) & lean concrete 1:2:4 including pointing the joints with white cement and matching etc. complete to the satisfaction of Site-In-Charge. (Rates of PCC under floors shall be paid separately.)

30.32

Sqm.

K-12 Granite Stone Slab on Counter Basin Top:- Providing & fixing 18 mm thick granite stone on counter basin slab laid on avg. 20 mm thick cement mortar 1:4 (1 Cement: 4 Coarse Sand , over RCC Slab of proper size & thickness to be paid extra. But this includes cost of cutting stone in desired shape fixing with cement slurry & the cost of nosing etc. complete as directed by Site-In-Charge. No

4.10

Sqm


Page 30 of 83

deductions for cut out area of basin.

K-13 Providing & fixing slate stone of average thickness 10 mm of desired shade in exteriors or as required in 1:3 Cement sand mortar including pointing the joints with pigmented cement slurry as per design & drawings, with all labor, material and T&P etc. complete as directed by Site-In-Charge.

64.01

sqm

Total Cost of Flooring & Paving work =

Note:-

1. Nothing extra payable for cutting, margins and wastage only ready to use area shall be measured. 2. Joints of tiles and stone shall be filled with similar color pigment mixed with

White cement in suitable proportion. 3. If unless specified finish for all stone works should be granite finished only.


Page 31 of 83

(L) POP &PAINT WORK

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) L-1 Providing & applying approved

1st quality Plaster of Paris (POP) punning to Walls & Ceiling of avg. 12 mm thickness to the line level and plumb including surface preparation required punning to be undertaken and complete in workman like manner to ensure desired finishing standard with all labor and T&P etc. complete as directed by Site-In-Charge.

1313.35 Sqm

L-2 Providing & applying Plaster of Paris (POP) Cornice in 1st quality of approved brand / moulding along the internal faces of wall / as directed by site in-charge, to be undertaken and completed in workman like manner to ensure desired finish / standard with all labor, material and T&P etc. complete as directed by Site-In-Charge.

239.73 Rmt.

L-3 Providing & applying OBD in Interior Painting-The surface to be painted shall be prepared to the satisfaction of Site-In-Charge and shall be applied with two coats of primer, two coats of putty and touch up putty if required to achieve smooth finish. The surface to be painted with two coats of approved Oil Bond washable distemper of desired shade and color complete with all labor, material and T&P etc.

4239.00 Sqm


Page 32 of 83

SOR No Description Qty Unit Rate (Rs.) Amount (Rs)

L-4 Exterior Painting- Providing and applying Acrylic smooth water proof exterior Paint of approved make two coats of desired shade and color after applying a coat of Primer, a coat of touch up exterior wall putty complete with all labor, material and T&P etc and up to the satisfaction of Site-In-Charge.

1975.41 Sqm

L-5

Finishing with Epoxy Paint (two or more coats) at desired location including Priming coat as per manufacturers standard specifications, including preparation of surface with all labor, material and T&P etc. complete up to the satisfaction of Site-In-Charge.

872.61 Sqm

L-6 Finishing with two coats of synthetic enamel paint approved brand over new work with touch up putty as required complete up to the satisfaction of Site-In-Charge.

46.00 Sqm

L-7 Providing & applying priming approved brand coat over new work complete up to the satisfaction of Site-In-Charge. a. Ready mixed pink or grey primer over wood work (hard or soft wood) b. Ready Mixed red oxide zinc chromate primer on steel work

24.50

21.00

Sqm

Sqm

L-8 Providing & applying two or more coats of malamine polish including surface preparation, & coats of wood filler as required

84.00 Sqm


Page 33 of 83

complete up to the satisfaction of Site-In-Charge.

Total Cost of POP & Paint work =

Note:- 1. All cement base paint to be cured for 4 to 5 days. 2. Scaffolding in inclusive in all items. 3. Surface preparation for all types of paint to be as directed by site-in-charge. Nothing extra

Payable for it. 4. All types of paints to be applied only after obtaining clearance of Site-in-charge.


Page 34 of 83

(M) INTERNAL WATER SUPPLY

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs) M-1 Providing and fixing 3 layer PP-

R (Poly propylene Random copolymer) pipes SDR 7.4U V stabilized & ant-microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain and brass threaded polypropylene random fitting i/c fixing the pipe with clamps at 1.00 m spacing complete as per direction of Site-In-Charge. For Internal/ external works, exposed on wall :

M-1.1 A.PN-16 Pipe, 25 mm OD 40.00 Mt M-1.2 A.PN-16 Pipe, 32mm OD 82.00 Mt. M-1.3 A.PN-16 Pipe, 50mm OD 20.00 Mt. M-2 Providing and fixing 3 layer PP-

R (Poly propylene Random copolymer) pipes SDR 7.4U V stabilized & ant-microbial fusion welded, having thermal stability for hot & cold water supply including all PP-R plain and brass threaded polypropylene random fitting i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chase and making good the same including testing of joints complete as per direction of site-in-charge. Concealed work including cutting chase and making good the walls etc. :


Page 35 of 83

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs)

M-2.1 PN-16 Pipe, 16mm OD 176.00 Mt. M-2.2 PN-16 Pipe, 20mm OD 212.00 Mt. M-2.3 PN-16 Pipe, 25 mm OD M-2.4 PN-16 Pipe, 32mm OD 135.60 Mt.

M-3

Providing and fixing / laying heavy duty PVC pipe for internal drainage Rain water disposal and external plumbing line with all necessary fittings clamps, collors, bends, tee material, labor and T&P etc. complete.

M-3.1 100 mm Dia (4’’) 125.00 Mt. M-3.2 150 mm Dia (6’’) 26.00 Mt. M-4 Constructing brick masonry

manhole in cement mortar 1:4 (1 cement:4 coarse sand) R.C.C top slab with 1:2:4 mix (1 cement : 2 coarse sand:4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand:8 graded stone aggregate 40mm nominal size) inside plastering thick 12 mm thick with cement mortar 1:3 (1 cement:3 coarse sand) finished with floating coat of neat cement and making channel in cement concrete 1:2:4 mix (1 cement : 2 coarse sand:4 graded stone aggregate 20mm nominal size) finished with a floating coat of neat cement complete as per standard design :


Page 36 of 83

SOR No. Description Qty Unit Rate (Rs.) Amount (Rs)M-4.1 Inside size 90X80 cm and 60 cm

deep including C.I cover with frame (light duty) 455x610mm internal dimensions total weight of cover and frame to be less than 38kg. (weight of cover 23 kg and weight of frame 15 kg.)

1 Each

M-4.2

Inside size 120x90 cm and 90cm deep including C.I cover with frame ( heavy duty) 560mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg.)

1 Each

Total Cost of Internal Water Supply work = Note:-

1. Union on every connection before the pipe line enters in the room or toilet. 2. Union will have to be provided for urinal pipe line as per the instructions. 3. All water supply lines shall be checked @ a pressure of 6 Kg/Sq.cm


Page 37 of 83

(N) PLUMBING & SAINITAION WORK

SOR No.

Description

Qty

Unit

Rate (Rs.)

Amount (Rs)

N-1 Providing & fixing white/

coloured Vitreous China orissa type water closet pan of size 580x480mm with integral type foot rests with seat and lid, 10 Liter low level white P.V.C flushing cistern with manually controlled device (handle cover) with all accessories, fitting and fixtures complete including cutting and making good the walls and floors wherever required up to the satisfaction of Site-In-charge.

2 No’s Each

N-2.1 Providing & fixing white/ coloured vitreous china, floor mounted European type water closet with seat &lid, 10 Liter low level white/colored chinaware (same make as of closet) flushing cistern & C.P flush bend with fitting & C.I brackets, 40 mm flush bend, CP Jet with connections, over flow arrangement with specials of standard make & mosquito proof coupling of approved municipal design complete including painting of fitting and brackets, cutting and making good the walls and floors wherever required up to the satisfaction of Site-In-Charge.

2 Nos

N.2.2 Do as per N-2.1 but with wall hung E.W.C

1 No’s Each


Page 38 of 83

N.2.2 Do as per N-2.1 but wall hung EWC and concealed cistern complete as instructed

3 No’s Each

N-3 Providing & fixing white vitreous china back half stall Urinal of size 580x380x250 mm with Sensor urinal flusher of desired type with 4 “AA” alkaline batteries & all accessories & fittings required.

N-3.1 Single urinal 2 No’s Each N-3.2 Do as N-3 but with white PVC

automatic flushing cistern of 10 litre, with fitting, standard size C.P brass flush pipe, spreaders with unions and clamps ( all in C.P brass with waste fitting C.I trap with outlet grating and other coupling in C.P brass including painting of fitting and cutting and making good the walls and floors wherever required .

1 No’s

Each

N-3.2 -DO- as N-3 but with water less mechanism using recyclable trap with bio degradable sealant for 15000 average uses complete with all accessories .

2 Nos

Each

N-3.3 Providing & fixing urinal Partitions in mirror polished Raj Nagar white marble 18 mm thick, complete with S.S supporting system, brackets & other necessary items as required for proper completion of job up to the satisfaction of Site-In-Charge.

3 No’s

Each

N-4 Providing and fixing china glazed vitreous counter type wash basin with C.P brass, waste of standard pattern/ bottle

4 No’s Each


Page 39 of 83

trap, PVC connections & CP basin mixture of approved quality with all accessories including all labor, material and T&P etc. complete.

N-5

White vitreous China pedestal type wash basin with C.P brass, waste of standard pattern, PVC connections & Basin mixture etc complete including all labor, material and T&P etc. complete.

4 No’s

Each

N-6 Providing & fixing stainless steel kitchen sink with C.I brackets and stainless steel plug 40mm including painting of fitting and brackets, cutting and making good the walls the wherever required : 510x1040mm with bowl depth 200mm

1

Each

N-7 Providing and fixing beveled edge mirror of superior glass (of approved quality) and of required shape and size with polished Teak wood frame in desired shape with 6mm thick hard board backing :

N-7.1

N-7.2 N-7.3

Rectangular shape 1500x1500 mm Oval 450x350mm Rectangular 600x400 mm

2 No’s

2 No’s 2 No’s

Each

Each Each

N-7.4 Providing and fixing C.P. brass long nose Bib cock of approved quality confirming to IS standards and weighing not less than 690gms :

15mm nominal bore. 10 No’s Each N-8 Providing and fixing C.P. brass

Stop cock (concealed) of standard design and of approved


Page 40 of 83

make confirming to Site-In-Charge.

15mm nominal bore. 8 No’s Each N-9 Providing and fixing C.P. brass

Angle valve for design mixer and geyser points of approved quality confirming to Site-In-Charge.

15mm nominal bore. 30 No’s Each N-10 Providing & fixing Pre approved

CP brass Telephonic wall mixture complete with all accessories required for proper completion of work to the satisfaction of Site-In-Charge.

4 No’s

Each

N-11 Providing & Fixing gun metal gate valve with CI wheel of pre approved quality (screwed end) complete with items required for proper completion work to the satisfaction of Site-In charge a. 25 mm nominal bore

c. 32mm nominal bore d. 50 mm nominal bore

2 Nos 2 Nos 1 nos

Each Each Each

N-12 Providing & fixing gun metal non-return valve of approved quality (screwed end) complete with items required for proper completion work to the satisfaction of Site-In charge a. 80 mm vertical nominal bore

1 No

Each

N-13 Supplying and fixing Pre-approved, CP brass toilet paper holder with fixing materials complete to the entire satisfaction of the Site-In-charge

8 No’s Each

N-14 Supplying & fixing pre approved Soap dispensers 500 ml capacity in CP finish with fixing materials

8 Nos Each


Page 41 of 83

etc complete to the satisfaction of Site-In-charge

N-15 Supplying & fixing pre approved Towel rails in CP finish & of desired pattern/ type with fixing materials etc complete to the satisfaction of Site-In-charge. 600mm x200mm

8 Nos

Each

N-16 Supplying & fixing pre approved Soap Tray in CP finish with fixing materials etc complete to the satisfaction of Site-In-charge

8 Nos Each

N-17 Supplying & fixing pre approved S.S body tissue paper dispenser with a capacity of 500 tissue papers along with all accessories as required for proper completion of job complete to the satisfaction of Site-In-charge.

2 Nos

Each

N-18 Providing & fixing C.I Nahni Traps 100x100x75mm (inside) with hinged CP cover jali, fixed in concrete 1:2:4 mix including necessary excavation as required complete to the satisfaction of Site-in-Charge

12 No’s Each

Total Cost of Plumbing & Sanitation work =


Page 42 of 83

(O) MISCELLANEOUS WORK:- SOR No. Description Qty Unit Rate (Rs.) Amount

(Rs) O-1 Providing & laying fiber glass

glass asphalt singles (fire halt) of desired shade on sloping roof with the help of Tar plastic adhesive, and roofing nails fixed at 8 inches distance, including a coat of bituminous primer, lining the gutter valleys with 2 ft. wide strip of APP modified bitumen membrane reinforced with glass fiber tissue, fixing of starter strip as first course and finally fixing hips and ridges as per manufacture’s specification complete in all respect to the satisfaction of Site-In-Charge.

27.50 sqm

O-2 Providing & fixing polyethylene water storage tank with all fittings, inlet & outlet connections, float valve, cover and suitable locking arrangement etc as per directions of Site-In-Charge. (2 Nos’ Water Tank 5000/lts per Tank)

10000 Lts.

Total Cost of Miscellaneous =


Page 43 of 83

ARYABHATTA RESEARCH INSTITUTE OF OBSERVATIONAL SCIENCES (ARIES)

SUMMARY OF PART -II

(ELECTRICAL WORKS FOR S.T. RADAR BUILDING AT NAINITAL)

S.NO DESCRIPTION AMOUNT (Rs) 1. LIGHTS & FIXTURES 2. DISRIBUTION BOARDS 4. SDB’s (RAW POWER) 5. SDB’s (UPS) 5. EXTERNAL LIGHTING 6. MAIN LT PANEL 7. LIGHTING AND SURGE ARRESTER 8. POINT WIRING 9. EARTHING

10. CABLES & CONTAINMENTS 11. MISCELLANEOUS

TOTAL ELECTRICAL WORK Rs. TOTAL AMOUNT IN WORD (Rs._____________________________________________ __________)


Page 44 of 83

(1) LIGHTS & FIXTURES

S.No DESCRIPTION QTY UNIT RATES AMOUNT A LIGHT FIXTURES Supply, installation, testing &

Commissioning of following light fixtures(all types) of pre approved make complete with control gear, lamps(CFL lamp of proper wattage approved by engineer in charge will be used everywhere) , fixing and mounting directly on ceiling, wall trusses with all accessories including connections complete to the satisfaction of Engineer in charge .

A-1 2*28 W FTL T5, with corrosion proof IP65 fitting Powder coated with reflector, fully enclosed (with top cover)

72 Nos.

A-2 1*28 Wt. T-5 lamps with corrosion proof IP65 fitting Powder coated with reflector, fully enclosed (with top cover).

18 Nos.

A-3 Supply, installation, Test, Commission of FBH 145 2x18 watts cone light with Electronic ballast, recess mounted/suspended fixtures, supporting arrangement to be suspended from ceiling, including painting ,tubes to be installed with T5 Lamp.

10 Nos

A-4 Supply, installation, Testing, Commissioning of 1x36 watts box type light fitting with Electronic ballast, recess mounted fixtures , includes assembling of choke supplied by the supplier, supporting arrangement to be suspended, including painting if required from ceiling. tubes to be installed with T5 Lamp.

2 Nos

A-5 Supply, installation, test & commission


Page 45 of 83

of Pre approved Standard dimmable electronic ballast device for any type of lamp with lighting dimmable range 30%-100% under control of micro control core chip, to ensure no flicking in dimmable output.

4 5

Nos

A-6 Installation, test and commissioning of light fixtures including cost of hooks, hardware along with required accessories etc. complete as directed

40 Nos

B Supply, installation, test & commissioning of following Exhaust Fans of pre approved make complete with all accessories including making holes to suite the size of fan ,making good the damages, etc. complete as required up to the satisfaction of engineer in charge.

B-1 24’’ Heavy Duty Exhaust Fan with duly designed impeller for high speed, Blades aerodynamically balanced for low air turbulence and low noise, lower power consumption and high efficiency, with minimum guaranteed 10450 Cubic M/Hr Air delivery, 1400 RPM, as per IS:2312-1967

6 Nos.

B-2 SITC 12” Exhaust fan with louvers in 1400 RPM, 75 watt, air delivery 2000 Cum/Hr of high efficiency.

3

Nos

B-3 Do as B-2, but for 9” exhaust fan. 3 Nos C ELECTRIC GEYSERS

C-1 Supply, installation, test & commissioning of highly efficient Electric Geysers 25L COMPACT SS TANK with imported comb stat, auto cut, PUF installation for 30% energy saving over ISI norms with thermally insulated copper tank of pre approved quality.

4 Nos.

D ELECTRIC HEATERS D-1 Supply, installation, test &

commissioning of pre approved ISI marked Oil filled room heaters with 11 Fins, Noiseless operation, Three heat settings, Thermostat control to maintain desired room temperature, Built-in safety

12 Nos.


Page 46 of 83

fuse, Unique safety switch against tilting, Castor wheels for easy mobility,

TOTAL OF LIGHT & FIXTURES

(2-1) RAW POWER DISRIBUTION BOARDS

S.No DESCRIPTION QTY UNIT RATES AMOUNT

DISTRIBUTION BOARDS & SUBMAIN BOARDS (FOR LIGHTING LOAD - FACTORY & OFFICE)

A Supply, Installation, testing & commissioning of Distribution Board, IP55 TYPE A(dust & vermin proof with lockable arrangement) made out of 16 gauge M.S Sheet duly wired. All outgoings shall be wired to terminal blocks in a cable alley with proper marking on each terminal block. The Distribution board will be having 200A Copper Bus bar of size 40x5 mm. The distribution board shall have proper ventilation and electrical panels should be painted with approved colour complete as directed.

1

NOS

B INCOMING B-1 400 Amp 4 Pole MCCB 35 KA WITH

ELECTRONIC TRIP UNIT WITH ICS =100%ICU

1 Nos

B- 2 Digital VAF Meter for metering 1 Nos C OUTGOING

C-1 63 A FP MCB ,C Curve( MCB for switch and socket load)

6 Nos

C-2 32 A FP MCB C Curve(MCB for lighting and fan Load)

6 Nos

TOTAL COST OF DISTRIBUTION RS.


Page 47 of 83

(2-2) UPS POWER DISRIBUTION BOARDS

S.No DESCRIPTION QTY UNIT RATES AMOUNT DISTRIBUTION BOARDS & SUBMAIN

BOARDS (FOR LIGHTING LOAD - FACTORY & OFFICE)

A Supply, Installation, testing & commissioning of Distribution Board, IP55 A Type ,made out of 16 gauge M.S Sheet duly wired. All outgoings shall be wired to terminal blocks in a cable alley with proper marking on each terminal block. The Distribution board will be having 200A Copper Bus bar of size 40x5 mm. The distribution board shall have proper ventilation of electrical panel.

1 NOS

B INCOMING B-1 400 Amp 4 Pole, 35 KA MCCB WITH

ELECTRONIC TRIP UNIT WITH ICS =100%ICU

1 Nos


C-1 63 A FP MCB10 KA C Curve MCB (for switch and socket load

6 Nos

C-2 32 A FP MCB 10 KA C Curve(MCB for lighting and fan Load)

6 Nos



Page 48 of 83

(2-3) A.C DISRIBUTION BOARDS

S.No DESCRIPTION QTY UNIT RATES AMOUNT DISTRIBUTION BOARDS & SUBMAIN

BOARDS (FOR LIGHTING LOAD - FACTORY & OFFICE)

A Supply, Installation, testing & commissioning of Distribution Board, IP55,A TYPE made out of 16 gauge M.S Sheet duly wired. All outgoings shall be wired to terminal blocks in a cable alley with proper marking on each terminal block. The Distribution board will be having 200A Copper Bus bar of size 40x5 mm. The distribution board shall have proper ventilation of electrical panel.

1

Nos

B INCOMING B-1 400 Amp 4 Pole, 35 KA MCCB with

electronic trip unit ICS=100% ICU 1 Nos


C-1 250 Amp FP MCCB 35 KA with electronic trip unit ICS=100% ICU (For 60 TR unit @ Meznine)

1

Nos

C-2 100 Amp FP MCCB 35 KA with electronic trip unit ICS =100% ICU ( RC Room + Computer Room)

2

Nos

C-3 32 A FP MCB 10 KA C Curve(MCB for Library/ Conference)

2 Nos


Total cost of DB’s (2.1 To 2.3) =


Page 49 of 83

(3-1) Sub Distribution Boards

Sr. No.

DESCRIPTION QTY UNIT RATES AMOUNT

SUB DISTRIBUTION BOARDS (FOR INTERNAL LIGHTING LOAD)

A Supply, Installation, testing & commissioning of SUB Distribution Boards, Double Door,lockable Type, IP42 protection, with detachable top and bottom gland plates, having 10kA short circuit protection. The wiring shall be with 6 sq mm copper wire for 32A MCB, 4 sq mm for 20A MCB, and 2.5 sq mm for 16A and 10A MCB.

a) 12way TPN DB for Student Room + Library / Conference + Toilet Block + Drinking Water INCOMING

1 NOS

1 63 Amp 4 Pole MCB 10 KA, C-Curve type for switch and socket Load

1 Nos.

2 32 Amp 4 Pole MCB 10KA, C-Curve type for Lighting and Fan load

1 Nos.

OUTGOING 1 16A MCB DP C Curve for 5A 5Pin Switch

(Each for Student Room (5) + Library (7) + Drinking Water (1))

3 Nos.

2 32 A DP MCB C Curve for 15A 5Pin, Switch and socket (MCB for Student Room (2))

1 Nos.

3 20 A DP MCB C Curve for 15A 5Pin, Switch and socket (MCB for Student Room (1) + Library / Conference(1))

2 Nos.

4 10 A DP MCB C Curve for Raw power light (Each for Student Room (5)+ Library / Conference (9) + Toilet Block (2)+ Drinking Water(2))

3 Nos.

5 16 A DP MCB C Curve for exhaust Fan (For Toilet Block + Drinking Water (3))

1 Nos.

TOTAL COST OF DISTRIBUTION RS. Note: 1. Rates shall include FRLS wring / cabling, conduiting, etc. complete in all respect from

distribution board to SDB . 2. The size of wire/cable from DB to SDB will be 1.5 times of total capacity of SDB/SDBs 3. All MCB’s should be of 10 KA current breaking capacity.



Page 50 of 83

Sr. No.



A Supply, Installation, testing & commissioning of Distribution Boards, Double Door lockable Type, IP42 protection, with detachable top and bottom gland plates, having 10kA short circuit protection. The wiring shall be with 6 sq mm copper wire for 32A MCB, 4 sq mm for 20A MCB, and 2.5 sq mm for 10 and 15A MCB.

a) 12 way TPN DB for Scientist Room (4 Nos) + PDF Rooms (2Nos) + Admin Room + Guest Room INCOMING

1 NOS

1 63 Amp 4 Pole MCB 10 KA , C-Curve type for switch and socket load

1 Nos.

2 10 Amp 4 Pole MCB 10 KA, C-Curve type for lighting load

1 Nos.

OUTGOING 1 16A, MCB DP, C Curve for 5A, 5Pin

Switch (Each for Scientist Room-1 (2) + Scientist Room-2 (2) + Scientist Room-3 (2) + Scientist Room-4 (2) + PDF Room-1 (2)+ PDF Room-2 (2) + Admin (2) + Guest Room (2))

8 Nos.

2 2 A, DP MCB, C Curve for Raw power light (Each for Scientist Room-1 (1) + Scientist Room-2 (1) + Scientist Room-3 (1) + Scientist Room-4 (1) + PDF Room-1 (1)+ PDF Room-2 (1) + Admin (1) + Guest Room (1) + Corridor (5))

9 Nos.

TOTAL COST OF DISTRIBUTION RS. Note:

1. Rates shall include FRLS wring / cabling, conduiting, etc. complete in all respect from distribution board to SDB .

2. The size of wire/cable from DB to SDB will be 1.5 times of total capacity of SDB/SDBs 3. All MCB’s should be of 10 KA current breaking capacity.


Page 51 of 83


Sr. No.



A Supply, Installation, testing & commissioning of Distribution Boards, Double Door,lockable Type, IP42 protection, with detachable top and bottom gland plates, having 10kA short circuit protection. The wiring shall be with 6 sq mm copper wire for 32A MCB, 4 sq mm for 20A MCB, and 2.5 sq mm for 10 and 15A MCB.

a) 12way TPN DB for RC Room + Electronic lab INCOMING

1 NOS

1 63 Amp 4 Pole MCB 10 KA, C-Curve type for switch and socket load

1 Nos.

2 6 Amp 4 Pole MCB 10 KA , C-Curve type for lighting load

1 Nos.

OUTGOING 1 6A, MCB DP, C Curve for 5A ,5Pin Switch

(Each for Electronic Lab(1))

1 Nos.

2 32 A ,DP MCB, C Curve for 15A 5Pin, Switch and socket (MCB for RC Room (2))

1 Nos.

3 20 A ,DP MCB ,C Curve for 15A ,5Pin, Switch and socket (MCB for RC Room (1) + Electronic Lab(1))

2 Nos.

4 6 A, DP MCB, C Curve for Raw power light (Each for Room Room-1 (2) + Electronic Lab-2 (3))

2 Nos.





Page 52 of 83


Sr. No.



A Supply, Installation, testing & commissioning of Distribution Boards, Double Door, lockable Type, IP42 protection, with detachable top and bottom gland plates, having 10kA short circuit protection. The wiring shall be with 6 sq mm copper wire for 32A MCB, 4 sq mm for 20A MCB, and 2.5 sq mm for 10 and 15A MCB, including wiring etc complete from DB

a) 12way TPN DB for Computer Room + reception INCOMING

1 NOS

1 63 Amp 4 Pole MCB 10 KA , C-Curve type for switch and socket

1 Nos.


1 Nos.

OUTGOING 1 32 A, DP MCB, C Curve for 15A, 5Pin,

Switch and socket (MCB for Computer Room (4) + Reception(2))

3 Nos.

2 6 A, DP MCB ,C Curve for Raw power light (Each for Computer room (2) + Reception (8))

2 Nos.


Note: 1. Rates shall include FRLS wring / cabling, conduiting, etc. complete in all respect from



Page 53 of 83


Sr. No.



A Supply, Installation, testing & commissioning of Distribution Boards, Double Door lockable Type, IP42 protection, with detachable top and bottom gland plates, having 10kA short circuit protection. The wiring shall be with 6mm copper wire for 32A MCB, 4mm for 20A MCB, and 2.5mm for 10 and 15A MCB.

a) 12way TPN DB for Rest Room + Toilet (4 Sets) INCOMING

1 NOS


1 Nos.

2 10 Amp 4 Pole MCB 10 KA, C-Curve type for lighting and fan load

1 Nos.


(Each for Rest Room) 4 Nos.

2 20 A DP MCB C Curve for 15A 5Pin, Switch and socket (MCB for each rest room)

4 Nos.

3 2 A DP MCB C Curve for Raw power light (Each for Rest Room + Corridor(1))

5 Nos.

4 6 A DP MCB C Curve for exhaust Fan (For each Rest room Toilet Block )

2 Nos.





Page 54 of 83

(3-6) Sub Distribution Boards Sr. No.




a) 12 way TPN DB for Refreshing AREA. INCOMING

1 NOS


1 Nos.

2 10 Amp 4 Pole MCB 10 KA, C-Curve type for lighting and fan load

1 Nos.


(Each for Rest Room)

4 Nos.

2 32 A DP MCB C Curve for 15A 5Pin, Switch and socket (MCB for Refreshing room (2))

1 Nos.

3 20 A DP MCB C Curve for 15A 5Pin, Switch and socket (MCB for Refreshing room (1))

1 Nos.

4 2 A DP MCB C Curve for Raw power light (Each for Refreshing (3))

1 Nos.

5 16 A DP MCB C Curve for exhaust Fan (For Refreshing (3))

1 Nos.


TOTAL COST SDB’s (3.1to3.6) = Note:




Page 55 of 83

(4-1) UPS Sub Distribution Boards

Sr. No.



A Supply, Installation, testing & commissioning of Distribution Boards, Double Door, lockable Type, IP42 protection, with detachable top and bottom gland plates, having 10kA short circuit protection. The wiring shall be with 6 sq mm copper wire for 32A MCB, 4 sq mm for 20A MCB, and 2.5 sq mm for 10 and 15A MCB.

a) 12 way TPN DB for Student Room / Library Conference INCOMING

1 NOS


1 Nos.


1 Nos.

OUTGOING 1 32 A DP MCB C Curve for 15A 5Pin,

Switch and socket (MCB for Student room (2) + Library Conference (2))

2 Nos.

2 20 A DP MCB C Curve for 15A 5Pin, Switch and socket (MCB for Student room (1)+ Library Conference(1))

2 Nos.

3 6 A DP MCB C Curve for Raw power light (MCB for student Room (4)+ Library Conference(6))

2 Nos.





Page 56 of 83


Sr. No.




a) 12 way TPN DB for Scientist /Eng Room 4Nos. INCOMING

1 NOS


1 Nos.


1 Nos.

OUTGOING

1 32 A DP MCB C Curve for 15A 5Pin, Switch and socket (MCB for Scientist /Eng room (2))

4 Nos.

2 2 A DP MCB C Curve for Raw power light (MCB for Scientist / Eng Room (4 Nos.)+ Corridor(2))

5 Nos.


Note:




Page 57 of 83


Sr. No.



A Supply, Installation, testing & commissioning of Distribution Boards, Double Door, lockable Type, IP42 protection, with detachable top and bottom gland plates, having 10kA short circuit protection. The wiring shall be with 6 sq mm copper wire for 32A MCB, 4 sq mm for 20A MCB, and 2.5 sq mm for 10 and 15A MCB.

a) 12 way TPN DB for PDF Room 2Nos + Guest Room + Admin Room. INCOMING

1 NOS


1 Nos.

2 6 Amp 4 Pole MCB , C-Curve type for lighting load

1 Nos.


Switch and socket (MCB for PDF room-1 (2) + PDF room-2 (2) + Guest Room (2) + Admin Room (2))

4 Nos.

2 2 A DP MCB C Curve for Raw power light (MCB for PDF room (2 Nos)+ Guest Room(1) + Admin Room (1) + Corridor(3))

5 Nos.





Page 58 of 83


Sr. No.




a) 8 way TPN DB for RC Room INCOMING

1 NOS


1 Nos.


1 Nos.


Switch and socket (MCB for RC room (2)) 3 Nos.

2 2 A DP MCB C Curve for Raw power light (MCB for RC Room(3))

1 Nos.





Page 59 of 83


Sr. No.



A Supply, Installation, testing & commissioning of Distribution Boards, Double Door,lockable Type, IP42 protection, with detachable top and bottom gland plates, having 10kA short circuit protection. The wiring shall be with 6 sq mm copper wire for 32A MCB, 4 sq mm for 20A MCB, and 2.5 sq mm for 16A and 10A MCB.

a) 8 way TPN DB for Electronic Room INCOMING

1 NOS


1 Nos.


1 Nos.


Switch and socket (MCB for Electronic room (2))

3 Nos.

2 2 A DP MCB C Curve for Raw power light (MCB for RC Room(2))

1 Nos.





Page 60 of 83

(4-6) UPS Sub Distribution Boards Sr. No.



A Supply, Installation, testing & commissioning of Distribution Boards, Double Door,lockable Type, IP42 protection, with detachable top and bottom gland plates, having 10kA short circuit protection. The wiring shall be with 6 sq mm copper wire for 32A MCB, 4 sq mm for 20A MCB, and 2.5 sq mm for 16 and 10A MCB.

a) 8 way TPN DB for Computer Room and reception + Rest Room + Refreshing INCOMING

1 NOS


1 Nos.


1 Nos.


Switch and socket (MCB for Computer room (2) + Reception (2))

3 Nos.

1 20 A DP MCB C Curve for 16A 5Pin, Switch and socket (MCB for Computer room (1))

1 Nos.

2 4 A DP MCB C Curve for Raw power light (MCB for Computer Room(2) + Reception (5) + Rest Rooms (4) + Rest Room Corridor (1)+ Refreshing (2))

5 Nos.


Total cost of SDB’s (4.1 to 4.6) = Note:


2. The size of wire/cable from DB to SDB will be 1.5 times of total capacity of SDB/SDBs 3. All MCB’s should be of 10 KA current breaking capacity. 4. All MCCB should have the in-built features of ELCB.


Page 61 of 83

(5) EXTERNAL LIGHTING


1 Supply, fixing, testing & commissioning of weather proof pole/wall mounted boxes of 250mm x 300mm x 125mm deep made out of 16 SWG M.S sheet complete with 4 Nos. covered neutral links & 1 No. 6 A SP MCB for connecting the fittings & complete with double earth stud, neoprene gasket connections including painting with epoxy base paint etc. as required.Well Glass fitting 50W MH

6

Nos

2 Supply, fixing, test & commissioning Street light fitting suitable for 250 W MH lamp complete on 8 Mtr. high ST pole (including cost of ST pole complete with erection, concreting etc) bracket complete with 250 W MH lamp, control gear, including painting, grouting of poles,etc.

6 Nos

3 Supplying, fixing, test & commissioning of industrial type wall mounted type distribution board made out of 16 gauge MS sheet with supplying the following accessories including painting, inter connections etc (For External Lighting).

A INCOMING A-1 32 A 4 pole MCB C curve 1 Nos B OUTGOING

B-1 6 A DP MCB C Curve 10 Nos TOTAL COST OF EXTERNAL LIGHT

Note:




Page 62 of 83

(6) LT PANEL

S.No DESCRIPTION QTY UNIT RATES AMOUNT 1 Supplying, Installation, Testing &

Commissioning of L.T Panel suitable for working on 415 Volts, 300KW,50 C/S, 3 phase A.C supply made out of 14 gauge M.S sheet and complete with supplying & fixing the following accessories, making interconnections with Copper strip/copper wires, painting and complete as per detail specifications etc. as required.

1 Nos

A OUTGOING A-1 400 A FP MCCB with front operator handle

( 70 kA) WITH ELECTRONIC TRIP UNIT ICS =100% ICU (For ST RADAR facility)

1

A-2 400 A FP MCCB with front operator handle ( 70 KA) WITH ELECTRONIC TRIP UNIT ICS =100% ICU (For AC Plant)

1

A-3 400 A FP MCCB with front operator handle ( 70 kA) WITH ELECTRONIC TRIP UNIT ICS =100% ICU (For Internal Lighting Load)

1

A-4 320 A FP MCB with front operator handle ( 70 kA) WITH ELECTRONIC TRIP UNIT ICS =100% ICU (For External Lighting Load)

1

A-5 Spare Feeder 2 A-6 320 A FP MCCB with front

operator handle ( 70 kA) WITH ELECTRONIC TRIP UNIT ICS =100% ICU (For UPS System)

1

TOTAL COST OF MAIN LT PANEL RS.


Page 63 of 83

(7) LIGHTNING AND SURGE ARRESTER

S.No DESCRIPTION QTY UNIT RATES AMOUNT A Supply, Install, Test & Commission of

Lightening arrestor on the concept of Rod type lightening conductor, connected to earth efficiently works by altering, at its level, the equi-potentials which match the structures of the building it protects. The lightening arrestor should work on piezoelectric effect. The detailed specifications are as below:

1 Lightening Conductor Early streamer emission chromium copper 15/2 M

L.S

2 Standard Rods of Chromium Copper 5 Sq.MM

90 RM

3 Down Conductor Flat Conductor, tinned copper tape 30X2MM -50 SQMM

100 RM

4 Discharge counter 1 L.S 5 Control junction and couplings 1 L.S 6 Fixings 1 L.S 7 Back fill compound for lightening arrestor

earthing 4 BAGS

TOTAL COST LIGHTING AND SURGE ARRESTER RS.


Page 64 of 83

(8) POINT WIRING

S.No DESCRIPTION QTY UNIT RATES AMOUNT A Supply, Installation, test &

commissioning of following light points complete with control gear, modular switches/sockets fixing and mounting accessories complete as directed.

A-1 Wiring for switch controlled Primary Light point (PxNxE)with 1.5 Sq.mm PVC insulated FRLS stranded copper conductor 660/1100 Volt grade wires in PVC 25 mm surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of 6 A modular switch along with complete accessories like inner plate, outer plate and flush metal boxes with modular cover plate in zinc chromate passivity MS box, including the cost of running 1.5 sq mm PVC insulated FRLS stranded copper wire for loop earthing (from Switch board to require point)and including the cost of circuit wiring (PxNxE) with 2.5 sq. mm 660 volt grade PVC insulated FRLS stranded copper conductor wire from SDB to switch board , complete as required for 2*28W FTL T5.

72.00

NOS

A-2 Wiring for switch controlled Primary Light point(PxNxE) with 1.5 Sq.mm PVC insulated FRLS stranded copper conductor 660/1100 Volt grade wires in 25mm PVC surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of 6 A modular switch along with complete accessories like inner plate, outer plate and flush metal boxes with modular cover plate in zinc chromate passivity MS box, including the cost of running 1.5 sq mm PVC insulated FRLS stranded copper wire for loop earthing

18 NOS


Page 65 of 83

(from Switch board to require point)and including the cost of circuit wiring(PxNxE) with 2.5 sq. mm 660 volt grade PVC insulated FRLS stranded copper conductor wire, from SDB to switch board, complete as required for 1*28W FTL T5.

A-3 Wiring for switch controlled Secondary Light point (PxNxE)with 1.5 Sq.mm PVC insulated FRLS stranded copper conductor 660/1100 Volt grade wires in PVC 25 mm surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of 6 A modular switch along with complete accessories like inner plate, outer plate and flush metal boxes with modular cover plate in zinc chromate passivity MS box, including the cost of running 1.5 sq mm PVC insulated FRLS stranded copper wire for loop earthing and including the cost of sub circuit wiring with 2.5 sq. mm 660 volt grade PVC insulated FRLS stranded copper conductor wire from switch board to required point in sub circuit, complete as required for 2*28W FTL T5

10 NOS

A-4 Wiring for switch controlled Secondary Light point (PxNxE)with 1.5 Sq.mm PVC insulated FRLS stranded copper conductor 660/1100 Volt grade wires in PVC 25 mm surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of 6 A modular switch along with complete accessories like inner plate, outer plate and flush metal boxes with modular cover plate in zinc chromate passivity MS box, including the cost of running 1.5 sq mm PVC insulated FRLS stranded copper wire for loop earthing and including the cost of sub circuit wiring with 2.5 sq. mm 660 volt grade PVC insulated FRLS stranded copper conductor wire from switch board to required point in sub

10 NOS


Page 66 of 83

circuit, complete as required for 1*28W FTL T5

A-5 Wiring for switch controlled power point (PxNxE)with 2.5 Sq.mm PVC insulated FRLS stranded copper conductor 660/1100 Volt grade wires in 25mm PVC surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of modular switch & socket 6/16A (combined/separate as per requirement) along with complete accessories like inner plate, outer plate and flush metal boxes with modular cover plate in zinc chromate passivity MS box, including the cost of running 2.5 sq mm PVC insulated FRLS stranded copper wire for loop earthing and including the cost of sub circuit wiring with 4.0 sq. mm 660 volt grade PVC insulated FRLS stranded copper conductor wire, complete as required for computer systems from SDB.

60 NOS

A-6 Wiring for switch controlled power point (PxNxE)with 6.0 Sq.mm PVC insulated FRLS stranded copper conductor 660/1100 Volt grade wires in PVC surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of modular switch & socket (combined/separate as per requirement) along with complete accessories like inner plate, outer plate and flush metal boxes with modular cover plate in zinc chromate passivity MS box, including the cost of running 4.0 sq mm PVC insulated FRLS stranded copper wire for loop earthing and including the cost of circuit wiring with 6.0 sq. mm 660 volt grade PVC insulated FRLS stranded copper conductor wire, complete as required from SDB.

5 NOS

A-7 Wiring for TV point with RG-6 conductor

surface/concealed conduit including cost 6 NOS


Page 67 of 83

of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of modular type switch & TV socket along with complete accessories like inner plate, outer plate and flush metal boxes with modular cover plate in zinc chromate passivity MS box, including the cost of running RG-6 conductor from main junction box outside the building .

A-8 Wiring for Telephone point with required telephone conductor surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of modular switch & Modular Type RJ-11 (Telephone socket) along with complete accessories like inner plate, outer plate and flush metal elbows with modular cover plate in zinc chromate passivity MS box, including the cost of running telephone conductor & tag block from EPABX room/DBs to end points. Rate shall be inclusive of providing and fixing required pair of cables and accessories, junctions etc complete as directed.

64

NOS

A-9 Supply and laying of Telephone wire with required telephone conductor surface/ concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of junction boxes/Gang boxes of required capacity, switch with modular cover plate in zinc chromate passivity MS box, including the cost of running telephone conductor & tag block.

a. 4 pair

b. 10 pair

c. 50 pair

25

20

20

RM

RM

RM

A-10 Wiring for RJ-45 point with CAT-6 LAN cable surface/concealed conduit including cost of providing saddles ,etc. for surface


Page 68 of 83

conducting and/or cost of cutting and filling chases for recessed conducting and fixing of switch & Modular Type RJ-45 socket with shutter along with complete accessories like inner plate, outer plate and flush metal boxes with modular cover plate in zinc chromate passivity MS box, including the cost of running CAT-6 LAN conductor from server room.

40 NOS

A-11 FRLS PVC Conduiting for 32 mm surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting in zinc chromate passivity MS box, including all cost , complete as required

20 RM

A-12 FRLS PVC Conduiting for 25 mm surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting in zinc chromate passivity MS box, including all cost , complete as required

20 RM

A-13 FRLS PVC Conduiting for 20 mm surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting in zinc chromate passivity MS box, including all cost , complete as required.

20 RM

B Supply, Installation, test &

commissioning of following Exhaust Fan points

B-1 Wiring for switch controlled exhaust fan(PxNxE) point with 2.5 Sq.mm PVC insulated FRLS stranded copper conductor 660/1100 Volt grade wires in PVC surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of switch with modular cover plate in zinc chromate passivity MS box, including the cost of running 2.5 sq mm PVC insulated FRLS stranded copper

12 NOS


Page 69 of 83

wire for loop earthing and including the cost of circuit wiring with 4.0/2.5 sq. mm 660 volt grade PVC insulated FRLS stranded copper conductor wire, complete as required for 24"/12”/9” Heavy Duty Exhaust Fan each from SDB.

C Supply, Installation, test & commissioning of following Electric Geyser points

C-1 Wiring for switch controlled Power point (PxNxE)with 4.0 Sq.mm PVC insulated FRLS stranded copper conductor 660/1100 Volt grade wires in PVC surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of switch with modular cover plate in zinc chromate passivity MS box, including the cost of running 4.0 sq mm PVC insulated FRLS stranded copper wire for loop earthing and including the cost of circuit wiring with 6.0/4.0 sq. mm 660 volt grade PVC insulated FRLS stranded copper conductor wire, complete as required for Highly efficient Electric Geyser 25L COMPACT SS TANK from SDB.

10 NOS

D Supply, Installation, test &

commissioning of following Electric Heater points

D-1 Wiring for switch controlled Power point (PxNxE)with 4.0 Sq.mm PVC insulated FRLS stranded copper conductor 660/1100 Volt grade wires in PVC surface/concealed conduit including cost of providing saddles etc for surface conducting and/or cost of cutting and filling chases for recessed conducting and fixing of switch with modular cover plate in zinc chromate passivity MS box, including the cost of running 4.0 sq mm PVC insulated FRLS stranded copper wire for loop earthing and including the cost of circuit wiring with 6.0/4.0 sq. mm

32 NOS


Page 70 of 83

660 volt grade PVC insulated FRLS stranded copper conductor wire, complete as required for Electric room heaters from SDB.

E Plug and Socket to be fitted below false flooring with two Power switches of 6 A, /16 & sockets of 6/16 A with FRLS copper conductor 4 Sqmm wire for distribution purpose from SDB.

588 Nos

TOTAL COST OF POWER POINT RS.

Note: 1. Primary & Secondary light Points: The first light point connected directly with the switch board will primary light point and rest all other points in the switch board those are looped with first switch and other light points those are looped with the primary point will be secondary point. These all secondary points will also include the cost of switch, wires (PxNxE), conduiting from switch board/first light point, etc. to the required point. The cost of primary light point shall include conduiting, wiring from SDB via switchboard to required light point, cost of single switch, switch box, modular plate, etc. complete in all respect.

2. For each point all three wires (PxNxE) will be drawn separately. For each light point PxNxE wire

from switch board to required point will be of 1.5 Sq mm.

3. The size of wire from SDB to each switch board will be a) 2.5 sq mm for light point b) 2.5 sq mm for 6A power switch c) 4.0 sq mm for 16 A power switch

4. Point wiring shall include the wiring of points of any length from SDB via Switch board and switches to the end point including sub circuit.

5. Wires should be inclusive of all rates necessary to complete the wiring as specified

6. Switches having marking on them like Tube light, Exhaust fan, etc. will be preferred.


Page 71 of 83

(9) EARTHING


1 Supply, install, test & Commissioning of Instrument Earthing with earth resistance less than 1 ohm for field instruments complete with all material & labour required for proper completion of work. The earthing should be preferably with suitable electrode with bag fill compound.

2 NOS

2 Supply, install, test & Commissioning of instrument Earthing with earth resistance less than 1 ohm for ST Radar system complete with all material & labour etc required for proper completion of work. The earthing should be preferably with suitable electrode with bag fill compound complete in all respect & approved by engineer incharge

2 NOS

3 Supply, Install, copper strip 25x3 mm complete with jointing nut bolts, clamps to support the earth in the shaft as required to complete the installation,with PVC sleeve.

50 Rmt

4 Supply, Install, copper strip 50x6 mm complete with jointing nut bolts, clamps to support the earth in the shaft as required to complete the installation, with PVC sleeve

20 Rmt

6 Supply, Install, 8 G copper wires complete with jointing nut bolts, clamps to support the earth in the shaft as required to complete the installation.

20 Rmt

7 Supply, Install, 12 G copper wires complete with jointing nut bolts, clamps to support the earth in the shaft as required to complete the installation.

10 Rmt

8 Supply, Install, 16 Sq mm insulated copper wire complete with jointing nut bolts, clamps to support the earth in the shaft as required to complete the installation for clean earth.

20 Rmt

9. Providing and laying B class GI pipe pipe 50 mm surface/concealed including excavation, backfilling, concreting, cost of providing saddles etc for surface conduiting and/or cost of cutting and filling chases for recessed conducting

20 RM


Page 72 of 83

including all cost , complete as required and instructed.

10. Do as per item no 9 but with 40 mm B class GI pipe.

20 RM

11. Do as per item no 9 but with 32 mm B class GI pipe.

20 RM

TOTAL COST OF EARTHING RS.


Page 73 of 83

(10) CABLES & CONTAINMENTS

S.No DESCRIPTION QTY UNIT RATE AMOUNT A Supply , Install , Test , Commission 1100 V

XLPE armored cables in trenches( if not specified than 2ftx2ft in cemented trenches and /or 1m deep x1 ft wide in ground covered with bricks, sand, etc. ) , cable trays , ducts , over bed of sand , clamped to wall with suitable clamps, route markers, crimping lugs, flange type glands, double compressed gland, (all gland should be earthed ) insulation complete in all respect.

1 Power Cables 4x10 Sq MM Copper 600 RMT 2 Power Cables 4x16 Sq MM Copper 600 RMT 3 Power Cables 3 1/2x 35 Sq MM Al 100 RMT 4 Power Cables 3 1/2x240 Sq MM Al 400 RMT 5. Power Cables 3 1/2x300 Sq MM Al 300 RMT B Supply & Install perforated Al cable tray

as per approved makes complete with the supports, fist plates to be supported from the ceiling. Supporting material to be taken here.

1 150x50 mm 15 Rmt 2 300x50 mm 10 Rmt 3 450x50 mm 15 Rmt 4 Supply & Install perforated Al cable tray as

per approved makes complete with the supports, fist plates to be supported from the floor, supports to be taken here to be raised by 2"

4-a 550x150 mm 15 Rmt 4-b 550x70 mm 10 Rmt

TOTAL COST OF CABLES WORK

Note :1. Rate shall be inclusive of making cemented trenches or excavation, back filling, brick, route markers etc.

2. Providing cables upto 1.5m height where cable rise above ground as may be directed , laying in surface with clamp, nut Bolts, etc. complete in all respect.


Page 74 of 83

(11) MISCELLANEOUS

S.No Description Qty Unit Rates Amount 1 Supply & Install Danger / Earthing Plate.

6x10/2x2 sq inches respectively 2 Nos

2 Supply & Install Rubber mats, full sheet 6 Sqmt 3 Supply, Install First Aid Box in electrical

room for 10 person first aid in handy polypropylene box with carrying handle and internal partition .The design protect contents from dust and water penetration Contents:

a) First aid guidance leaflets b) 20 adhesive plaster (sterile) c) Two eye pads d) 4 triangular bandages e) 6 safety pins f) 6 HSE medium dressing 12 x12 sqcm g) 2HSE large dressing 18x18 sq cm h) 6 individual wrapped bites i) One pair disposable gloves

1 Nos

4 Supply, Install Eye washes with solution in electrical room.

a) Sterile single use emergency eye wash Solution Sodium chloride 0.9% w/v sterile water for ocular and tropical irritation and wound cleansing

b) 1 Pack of 25x20 ml pod.

1 Lot

5 Supply, Install, Test, Commission Fully automatic Hand dryer with double blower, heater

2 Nos

TOTAL COST OF MISCELLANEOUS RS


Page 75 of 83

ARYABHATT RESEARCH INSTITUTE OF OBSERVATIONAL SCIENCES (ARIES)

SUMMARY OF PART -III

(AIRCONDITIONING WORKS FOR S.T. RADAR BUILDING AT NAINITAL)

S.NO DESCRIPTION AMOUNT 1. AT GROUND FLOOR 2. AT MEZNINE FLOOR TOTAL

TOTAL AMOUNT IN WORD (Rs.______________________________________________________)


Page 76 of 83

GROUND FLOOR

S. No.

DESCRIPTION OF ITEM QUANTITY UNIT RATE AMOUNT

GROUP “A” 1. Supply, Installation, Testing &

Commissioning of Standard make AIR COOLED Ductable Split units with first charge of refrigerant gas & oil, positioning of indoor & outdoor units comprising of “COPELAND” Scroll Compressors in multiple circuit, DX Evaporator coil, thermostatic expansion device with external equalizer, air-cooled condensers with specially coated BLUE Fins, DIDW centrifugal blower, TEFC Motor, Micro- processor based control panel etc. All items shall be encased in sheet metal cabinet of following capacities

Capacity- 11.0 TR 2 NOS 2. Supply, Installation, Testing &

Commissioning of standard Make High Wall Split Units with 5 RMT of copper piping & interconnecting wiring each circuit, positioning of indoor & outdoor units of following capacities

A. Capacity- 2.0 TR 4 NOS TOTAL GROUP “A” GROUP "B" LOWER SIDE

WORK

3. GSS Rectangular ducting (Class VIII Galvanizing standard)

24 Gauge 10 SQM 22 Gauge 10 SQM 4. Duct Insulation with 6 mm thick

closed cell elastomeric foam (nitrile rubber)

10 SQM


Page 77 of 83

5. Duct Acoustic lining with 12 mm thick fiber glass rigid board (density 32 Kg/cb.mt.) covered with RP Tissue paper & 28 G perforated Al sheet

30 SQM

6. Extruded Aluminium Powder coated supply/ return air linear grills without volume control dampers

4 SQM

7. Extruded Aluminium Powder coated supply/ return air diffusers without volume control dampers

2 SQM

9. Hard PVC drain pipe of 25 mm dia with fittings duly insulated 60 RMT

10. Canvass connection with fire retardant cloth 4 NOS

11. Hard drawn copper refrigerant piping for Ductable Split units duly insulated with 9mm thick. Nitrile rubber.

64 RMT

12. Soft drawn copper refrigerant piping for Hi-wall units duly insulated with 9mm thick. Nitrile rubber & interconnecting cable.

100 RMT

13. Interconnecting electrical control cabling between indoor & outdoor units ( Ducted units )

66 RMT

16. Voltage Stabilizer A 5 KVA for 2.0 TR 4 Nos.

TOTAL GROUP "B" TOTAL GROUP “A” + “ B” - Rs

Distribution Of A.C Units

1. R.C ROOM + COMPUTER- 11.0 TR X 2 (DUCTABLE) 2. LIBRARY/ COFERENCE – 2.0 TR X 4


Page 78 of 83

MEZNINE FLOOR

S.NO DESCRIPTION OF ITEM QUANTITY UNIT RATE AMOUNT GROUP “A” 1. Supply Installation ,Testing

and Commissioning of Standard Make AIR COOLED Precision Air conditioners with first charge of refrigerant gas & oil, positioning of indoor & outdoor comprising of “COPELAND” Scroll Compressors in multiple circuit, DX Evaporator coil, thermostatic expansion device with external equalizer, air- cooled condensers with specially coated BLUE Fins, DIDW centrifugal blower, TEFC Motor, Micro- processor based control panel etc. All items shall be encased in sheet metal cabinet of following capacities:

Capacity- 10.0 TR 6 NOS TOTAL GROUP “A” GROUP "B" LOWER SIDE

WORK

2. GSS Rectangular ducting (Class VIII Galvanizing standard)

24 Gauge 200 SQM 22 Gauge 50 SQM

3. Duct Insulation with 6 mm thick closed cell elastomeric foam insulation (nitrile rubber)

200 SQM

4. Duct Acoustic lining with 12 mm thick fiberglass rigid board (density 32 Kg/cb.mt.) covered with RP Tissue paper & 28 G

50 SQM


Page 79 of 83

perforated Al sheet 5. Extruded Aluminium Powder

coated supply/ return air linear grilles without volume control dampers

16 SQM

6. Extruded Aluminium Powder coated supply/ return air diffusers without volume control dampers

4 SQM

7. Hard PVC drain pipe of 25 mm dia with fittings duly insulated 50 RMT

8. Canvass connection with fire retardant cloth 10 Nos

9. Hard drawn copper refrigerant piping for Precision Air conditioners

200 RMT

10. Interconnecting electrical control cabling between indoor & outdoor units

210 RMT

11. MS Stand for outdoor units Capacity- 10.0 TR

( Twin Compressors) 20 Nos.

TOTAL GROUP "B"

TOTAL GROUP “A” + “ B” - Rs


Page 80 of 83

ARYABHATTA RESEARCH INSTITUTE OF OBSERVATIONAL SCIENCES

(ARIES)

SUMMARY OF PART -IV

(FIRE SAFETY & SUPPRESSION WORKS FOR S.T. RADAR BUILDING AT NAINITAL)

S.NO Description Amount (Rs) A. FIRE SAFETY ITEMS GRAND TOTAL

TOTAL AMOUNT IN WORD (Rs.______________________________________ _________________)


Page 81 of 83

FIRE SAFETY & SUPPRESSION WORKS

S.NO ITEM QTY UNIT RATE AMOUNT

1. Providing & fixing smoke cum heat detectors (Multi Sensor) of approved quality confirming to ISI standards having compatibility with any make fire alarm complete with wiring in 2 core multi strand copper wire in PVC conduits 25 mm dia as per drawings complete to the satisfaction of Site-In-charge.

50

Nos

2. Providing & fixing 2 to 8 zone smoke detection cum fire alarm panels (For a complete group of detectors) of approved quality complete with battery backup, charging facility & common & zone wise hooter facility confirming to ISI standards along with all necessary items as per drawings complete to the satisfaction of Site-In-charge

1

Nos

3. Providing & installing CO2 cylinders (extinguishers), portable & mobile type of approved quality confirming to ISI standards as per drawings complete to the satisfaction of Site-In-charge


Page 82 of 83

a. 4.5 Kg 12 Nos b. 9.0 Kg 6 Nos c. 22.5 Kg

3 Nos

4. Providing & installing ABC type fire extinguishers (dry Powder type) of approved quality confirming to ISI standards as per drawings complete to the satisfaction of Site-In-charge

a. 10 Kg(Wheel based for easy movement)

2 Nos

5. Providing & installing first aid fire swinging hose reel complete with hose reel pipe (rubber hose) 20 mm dia of busting pressure 32 kg/cm of 30 m length & nozzle of approved quality confirming to ISI standards complete to the satisfaction of Site-In-charge

2

Nos

6. Providing & fixing high intensity fire alarms/ hooters of ISI marked approved quality with flasher in MS & ABS body attached to the detection panel complete with all accessories.

3

Nos

7. Providing & installing manual call box of ISI marked approved quality complete with chain & hammer & blinking facility having compatibility with any fire alarm & all accessories as required.

5

Nos


Page 83 of 83

8. Providing & installing Response Indicator ISI marked approved quality having compatibility with any fire alarm & all accessories as required.

3

Nos

9. Supplying escape gears containing two fire escape masks of fire retardant material with a provision of smoke filtration system to provide breathable air for at least 30 minutes & two fire escape blankets made of silicon coated fire retardant material of pre approved quality.

1

Set

10 Providing & fixing photo luminescent fire escape signage in the premises size 8”x4”.

12

Nos

Grand Total

Documents

OBSERVATIONAL SCIENCES (ARIES) S. T. …...For all earth & sand supplied for filling from outside deduction of 20% voids shall be made. 5. Necessary shoring & strutting of original