OUTSULATION - Dryvittest.dryvit.com/fileshare/doc/us/detail/ds107.pdfreinforced with panzer® mesh prior to standard mesh™ or standard plus mesh™. location of high impact zones

DS107

OUTSULATION® An Exterior Wall Insulation and Finish System

Outsulation System Installation Details

EPS INSULATION

The architecture, engineering and design of the project using the

08/0611DAW

DATE:REV:APPROVED BY:

DRYVIT RECOMMENDS THAT GROUND FLOOR

APPLICATIONS AND ALL FACADES EXPOSED TO

ABNORMAL STRESS, HIGH TRAFFIC, OR

DELIBERATE IMPACT HAVE THE BASE COAT

REINFORCED WITH PANZER® MESH PRIOR TO

STANDARD MESH™ OR STANDARD PLUS MESH™.

LOCATION OF HIGH IMPACT ZONES SHOULD BE

INDICATED ON CONTRACT DRAWINGS.

does not violate Dryvit's warranty. This detail is subject to change

®

version.

without notice. Contact Dryvit to insure you have the most recent

1.

NOTE:

and Dryvit specifically disclaims any liability for the use of this

any project. The project design professional determines, in its sole

discretion, whether this detail or a functionally equivalent alternative

is best suited for the project. Use of a functionally equivalent detail

detail and for the architecture, design, engineering or workmanship of

professional. All systems must comply with local building codes and

standards. This detail is for general information and guidance only

Dryvit products is the responsibility of the project's design

DRYVIT FINISH

Outsulation System®Outsulation System

DRYVIT OUTSULATION SYSTEM

BY OTHERS

DRYVIT REINFORCING MESH

EMBEDDED IN DRYVIT BASE COAT

DRYVIT BASE COAT

HIGH

IMPACT

DRYVIT BASE COAT

PANZER 15 OR 20 REINFORCING

MESH EMBEDDED IN DRYVIT BASE COAT

DRYVIT BASE COAT

SUBSTRATE

DRYVIT FINISH

SUBSTRATE

DRYVIT ADHESIVE


BY OTHERS



DRYVIT BASE COATNORMAL

IMPACT

DRYVIT BASE COAT

EPS INSULATION

DRYVIT ADHESIVE

OS 0.0.01

version.






1.professional. All systems must comply with local building codes and




®Outsulation System Grade Level - Termination At Concrete Curb

DRYVIT COMPATIBLE SEALANT WITH

CLOSED CELL BACKER ROD, BY OTHERS



DRYVIT DEMANDIT® OR COLOR PRIME™

ON SURFACE TO RECEIVE SEALANT

19 MM (3/4") MIN.

WRAP DRYVIT DETAIL MESH® 51 MM (2")

MINIMUM AT UNDERSIDE OF EPS

DRYVIT FINISH

FRAMING

DRYVIT ADHESIVE

EPS INSULATION

SUBSTRATE

BY OTHERS DRYVIT OUTSULATION SYSTEM

OS 0.0.02



ABNORMAL STRESS, HIGH TRAFFIC, OR

DELIBERATE IMPACT HAVE THE BASE COAT

REINFORCED WITH PANZER® MESH PRIOR TO

STANDARD MESH™ OR STANDARD PLUS MESH™.

LOCATION OF HIGH IMPACT ZONES SHOULD BE

INDICATED ON CONTRACT DRAWINGS.


®

NOTE:The architecture, engineering and design of the project using the

DAW

APPROVED BY:

10/0612

DATE:REV:

610 MM (2'-0") Max

(SEE NOTE 2)


08/0611DAW


DRYVIT RECOMMENDS THAT GROUND

FLOOR APPLICATIONS AND ALL FACADES

EXPOSED TO ABNORMAL STRESS, HIGH

TRAFFIC, OR DELIBERATE IMPACT HAVE

THE BASE COAT REINFORCED WITH

PANZER® MESH PRIOR TO STANDARD

MESH™ OR STANDARD PLUS MESH™.

LOCATION OF HIGH IMPACT ZONES SHOULD

BE INDICATED ON CONTRACT DRAWINGS.

1.

STOP FINISH APPROXIMATELY 51 MM (2")

BELOW GRADE.does not violate Dryvit's warranty. This detail is subject to change

®


version.

EXPANSION JOINT IS REQUIRED ALONG TOP

OF FOUNDATION IF 610 MM (2'-0") DIMENSION

IS EXCEEDED. and Dryvit specifically disclaims any liability for the use of this





3. SLOPE GRADE AWAY FROM WALL.

4.




2.

Outsulation System Foundation - Termination Above Grade®

203 MM (8") MIN. ABOVE

FINISHED GRADE OR AS

REQUIRED BY LOCAL CODE

DRYVIT DRYFLEX™ WATER

RESISTANT BASE COAT

AND DRYVIT FINISH



WRAP DRYVIT DETAIL MESH®

51 MM (2") MINIMUM AT

UNDERSIDE OF EPS

DRYVIT COMPATIBLE

SEALANT WITH BOND

BREAKER, BY OTHERS

DRYVIT FINISH

DRYVIT ADHESIVE

EPS INSULATION

SUBSTRATE

FRAMING


OS 0.0.03

NOTE:

Outsulation® SystemThe architecture, engineering and design of the project using the

05/063RS

APPROVED BY: REV: DATE:


®

version.


DRYVIT AQUAFLASH SHALL EXTEND TO

INTERIOR FACE OF FRAMING.

DRYVIT FLASHING TAPE SURFACE

CONDITIONER™ AND DRYVIT FLASHING

TAPE™ MAY BE USED IN LIEU OF

AQUAFLASH SYSTEM.REFER TO OS 0.0.05, 0.0.06 FOR

INTEGRATION OF SILL FLASHING.

2.

1. 3.









Rough Opening Preparation

STEP #3

APPLY DRYVIT AQUAFLASH

SYSTEM AT HEAD LAPPING

OVER JAMB APPLICATION

(SEE NOTE 3)

APPLY DRYVIT AQUAFLASH

SYSTEM AT JAMBS LAPPING

OVER SILL APPLICATION

(SEE NOTE 3)

APPLY DRYVIT AQUAFLASH® SYSTEM

AT SILL, EXTENDING UP JAMBS

MINIMUM 64 MM (2 12") AND INSTALL

CORNER SPLICES (SEE NOTE 3)

STEP #1 STEP #2

OS 0.0.04

Outsulation® System

APPROVED BY:

RS 05/064

DATE:REV:





and Dryvit specifically disclaims any liability for the use of this detail

and for the architecture, design, engineering or workmanship of any

project. The project design professional determines, in its sole





version.

DRYVIT FLASHING TAPE SURFACE CONDITIONER™

AND DRYVIT FLASHING TAPE™ MAY BE USED IN

LIEU OF AQUAFLASH SYSTEM.

3.

®

PAN FLASHING SHOULD OVERLAP EIFS MIN. 2 1/2"

MEASURED FROM THE TOP OF THE EPS

PAN FLASHING MUST HAVE WATERTIGHT SEAMS2.

NOTES

1.

INSTALL WINDOW UNIT AND ASSOCIATED

HEAD FLASHING. (SEE DETAIL 0.0.09)

INSTALL EIFS AND APPLY BACKER

ROD AND SEALANT ALONG JAMBS

AND AT SYSTEM TERMINATIONS,

ALSO ALONG EDGES OF FLASHING.

Preparation of Opening for Storefront Window

STEP 3: STEP 4:

64 MM

(2 12") MIN.

PREPARE OPENING AS PER OS 0.0.04. INSTALL

SILL PAN FLASHING AND SECURE TO FRAMING AND

BLOCKING. SHIM UNDERSIDE OF FLASHING TO

ENSURE INCIDENTAL MOISTURE IS DIRECTED TO

THE EXTERIOR FACE OF THE WALL.

(SEE NOTES 1,2 AND 3)


SPLICES OVER UPTURNED LEGS OF PAN

FLASHING (SEE NOTE 3)

STEP 1: STEP 2:

(SEE NOTES 1 AND 2)

51 MM (2") MIN.

OS 0.0.05

(SEE NOTES 1,2 AND 5)

51 MM (2") MIN.

APPLY DRYVIT AQUAFLASH®

SYSTEM AT SILL PER OS 0.0.04

AND SECURE FLASHING TO

FRAMING

(SEE NOTES 1,2,5 AND 7)

INSTALL SILL PAN FLASHING. SHIM

UNDERSIDE OF PAN FLASHING TO

ENSURE WATER RUN OFF

(SEE NOTE 2)

STEP 1: STEP 2:

64 MM

(2 12") MIN.

OS 0.0.06

DATE:APPROVED BY: REV:

RS 4 05/06












version.

ADHESIVE ONLY APPLICATION IS

ACCEPTABLE WHEN USING THE

AQUAFLASH SYSTEM




AQUAFLASH SYSTEM. ®

7.

APPLY DRYVIT AQUAFLASH SYSTEM AT

SILL. (SEE DETAIL OS 0.0.04)

6.

5.

INSTALL EIFS AND APPLY BACKER ROD AND

SEALANT ALONG JAMBS AND AT SYSTEM

TERMINATIONS, ALSO ALONG EDGES OF

FLASHING (SEE NOTES 3,4,5 AND 6)

APPLY DRYVIT AQUAFLASH SYSTEM

OVER METAL FLASHING TRANSITION

AND AT JAMBS LAPPING OVER

UPTURNED LEGS OF PAN FLASHING (SEE

NOTES 1,2,5 AND 7)

Preparation of Opening for Nail-On Window

INSTALL WINDOW UNIT AND

ASSOCIATED HEAD FLASHING.

STEP 4: STEP 5:


PAN FLASHING SHOULD OVERLAP EIFS MIN. 64

MM (2 1/2") MEASURED FROM THE TOP OF THE

EPS

PAN FLASHING MUST HAVE WATER

TIGHT SEAMS

STEP 3:

MECHANICAL FASTENERS SHOULD BE USED TO

ATTACH SILL TRIM PIECE

EIFS AT SILL SHALL BE SLOPED FOR DRAINAGE.

NOTES

4.

3.

2.

1.

DRYVIT ADHESIVE



08/0614RS











®

version.





AQUAFLASH SYSTEM.

2.1.









64MM

(2-1/2") MIN.

SILL PAN FLASHING

DETAIL

Outsulation System®

Termination at Sill

12.7MM (1/2")

DRYVIT OUTSULATION SYSTEMBY OTHERS



DRYVIT FINISH

EPS INSULATION

AIR SEAL PER WINDOW MANUFACTURES

REQUIREMENT, BY OTHERS

FRAMING

SUBSTRATE

DRYVIT-COMPATIBLE SEALANT

WITH BOND BREAKER, BY OTHERS

64MM (2 12") MIN.

WRAP DRYVIT DETAIL MESH® 51 MM (2")

MINIMUM AT UNDERSIDE OF EPS.

CONTINUOUS FLASHING, BY OTHERS.

TURN UP 12.7MM (12") MIN. AT JAMBS

(SEE INSET)

DRYVIT AQUAFLASH® SYSTEM

(SEE NOTE 2)

WINDOW SYSTEM

AND SHIMS

OS 0.0.07

DRYVIT ADHESIVE



51 MM (2") MIN. AT UNDERSIDE OF EPS


(SEE NOTE 3)



08/0613RS


CONDITIONER™ AND DRYVIT FLASHING TAPE™

MAY BE USED IN LIEU OF AQUAFLASH

SYSTEM.











®

version.


SEALANT SHOULD NOT BE IN DIRECT

CONTACT WITH FLASHING TAPE ADHESIVE;

STAINING COULD OCCUR.detail and for the architecture, design, engineering or workmanship of

3.discretion, whether this detail or a functionally equivalent alternative



1. 2.and Dryvit specifically disclaims any liability for the use of this




DRYVIT DEMANDIT® OR

COLOR PRIME™ ON SURFACE

TO RECEIVE SEALANT



DRYVIT FINISH

Outsulation System®Termination at Jamb

DRYVIT-COMPATIBLE SEALANT

WITH CLOSED CELL BACKER ROD

BY OTHERS (SEE NOTE 2)

19 MM (3/4") MIN

EPS INSULATION

WINDOW SYSTEM

AND SHIMS

AIR SEAL PER WINDOW

MANUFACTURES


SUBSTRATE

BY OTHERS

FRAMING

OS 0.0.08

NOTE:


14RS 08/06










1.


®


version.




AQUAFLASH SYSTEM.









2.

AIR SEAL PER WINDOW

MANUFACTURES


Outsulation SystemThe architecture, engineering and design of the project using the

Termination at Head®

WINDOW SYSTEM

AND SHIMS

CONTINUOUS FLASHING AND

SEALANT (BY OTHERS)

19 MM (3/4") MIN.

SUBSTRATE


OVER LEG OF HEAD FLASHING

(SEE NOTE 2)

DRYVIT AQUAFLASH SYSTEM

(SEE NOTE 2)

DRYVIT DEMANDIT® OR COLOR PRIME™ ON

SURFACE TO RECEIVE SEALANT







DRYVIT FINISH

EPS INSULATION

DRYVIT ADHESIVE

OS 0.0.09


FRAMING




ON SURFACE TO RECEIVE SEALANT

DRYVIT AQUAFLASH SYSTEM

(SEE NOTE 2)

NOTE: Dryvit products is the responsibility of the project's design


12DAW 08/06











®

version.




AQUAFLASH SYSTEM.

1.2.









WINDOW SYSTEM

AND BLOCKING

AIR SEAL PER WINDOW

MANUFACTURES


®Outsulation SystemThe architecture, engineering and design of the project using the

Termination at Head-Solid Substrate

CONTINUOUS FLASHING AND

SEALANT, BY OTHERS

19 MM (3/4") MIN.

SOLID SUBSTRATE


OVER LEG OF HEAD FLASHING

(SEE NOTE 2)





DRYVIT FINISH

EPS INSULATION

DRYVIT ADHESIVE

OS 0.0.10


version.


LOCATE INSULATION BOARDS SUCH THAT

BOARD EDGES DO NOT ALIGN WITH CORNERS

OF PENETRATION.





1. standards. This detail is for general information and guidance only



®Outsulation System EPS Preparation at Wall Penetrations


DRYVIT DETAIL MESH

241 MM (9 1/2") X 305 MM (12") (TYP.)

(SEE NOTE 2)

BACK WRAP INSULATION BOARD

WITH DRYVIT DETAIL MESH®

EPS INSULATION (SEE NOTE 1)

OS 0.0.11

Dryvit products is the responsibility of the project's designNOTES:


05/06DAW 11


APPLY A PIECE OF 241 MM (9 1/2") X 305 MM

(12") DETAIL REINFORCING MESH DIAGONALLY

AT EACH CORNER.

®

version.

EXPANSION JOINT IS INTENDED TO

ACCOMMODATE CROSS GRAIN SHRINKAGE

OF FLOOR BEAMS. detail and for the architecture, design, engineering or workmanship of





3. LOCATE EXTERNAL SEALANT JOINT WITHIN

51 MM (2") BELOW BREAK IN SHEATHING.



professional. All systems must comply with local building codes and2.1.

®Outsulation System Wood Framing - Expansion Joint At Floor Line


WOOD FRAMING

SUBSTRATE

DRYVIT ADHESIVE

SEE NOTE 3

DRYVIT COMPATIBLE SEALANT

WITH CLOSED CELL BACKER ROD,

BY OTHERS

DRYVIT DEMANDIT® OR

COLOR PRIME™ ON SURFACES

TO RECEIVE SEALANT

SLOPE BOTTOM SURFACE

1/5 MIN. OUTWARD TO DRAIN

19 MM (3/4") MIN.

DRYVIT FINISH

EPS INSULATION



OS 0.0.12



51 MM (2") MIN. AT UNDERSIDE

OF EPS



DAW 08/0611











®



SLIP TYPE

CONNECTION

19 MM (3/4") MIN.


11DAW 08/06

LOCATE EXTERNAL SEALANT JOINT WITHIN

51 MM (2") BELOW BREAK IN SHEATHING.











REV:APPROVED BY:

®

DATE:

version.

EXPANSION JOINT IS INTENDED TO

ACCOMMODATE MOVEMENT AT SLIP

CONNECTION.

3.

2.1.









®Outsulation SystemThe architecture, engineering and design of the project using the

Light Gauge Framing - Expansion Joint At Floor Line

SLOPE BOTTOM SURFACE 1/5 MIN.

OUTWARD TO DRAIN



DRYVIT FINISH

SEE NOTE 3


ON SURFACES TO RECEIVE SEALANT

DRYVIT ADHESIVE

EPS INSULATION



SUBSTRATE

OS 0.0.13


OS 0.0.14

version.





1. standards. This detail is for general information and guidance only2.




Termination at Parapet-Cap Flashing®Outsulation System


DRYVIT FINISH



EPS INSULATION

PARAPET COPING ASSEMBLY,

BY OTHERS


BOND BREAKER, BY OTHERS

WRAP DRYVIT REINFORCING MESH

AND BASE COAT OVER TOP OF FRAMING

(SEE NOTE 2)

FRAMING

ROOF

ASSEMBLY

SUBSTRATE

64 MM (2 1/2") MIN.


08/0612DAW












AS AN OPTION, DRYVIT AQUAFLASH®

SYSTEM OR DRYVIT FLASHING TAPE

SURFACE CONDITIONER™ AND DRYVIT

FLASHING TAPE™ MAY BE USED TO

PROVIDE ADDITIONAL PROTECTION AT THE

TOP OF A PARAPET WALL.

®


DRYVIT ADHESIVE

DRYVIT REINFORCING

MESH EMBEDDED IN

DRYVIT BASE COAT

203 MM (8") MIN.

NOTE:Dryvit products is the responsibility of the project's design

RS 08/0714

AS AN OPTION, DRYVIT AQUAFLASH®

SYSTEM OR DRYVIT FLASHING TAPE

SURFACE CONDITIONER™ AND DRYVIT

FLASHING TAPE™ MAY BE USED TO

PROVIDE ADDITIONAL PROTECTION AT THE

TOP OF A PARAPET WALL.










version.









2.1.

®Outsulation System Termination at Parapet - Solid Substrate



DRYVIT FINISH

PARAPET COPING ASSEMBLY,

BY OTHERS WRAP DRYVIT DETAIL

MESH 51 MM (2") MIN.

AT UNDERSIDE OF EPS

(SEE NOTE 2)

WRAP DRYVIT REINFORCING MESH

AND BASE COAT OVER TOP OF

FRAMING (SEE NOTE 2)

DRYVIT COMPATIBLE

SEALANT, BY OTHERS

DRYVIT COMPATIBLE

SEALANT WITH BOND

BREAKER, BY OTHERS

SOLID SUBSTRATE

ROOF FLASHING AND COUNTER

FLASHING BY OTHERS

ROOF ASSEMBLY

EPS INSULATION

DRYVIT ADHESIVE

64 MM (2 1/2") MIN.



OS 0.0.15


®


EDGE/REGLET DETAIL SHOWN

IN ENLARGED SECTION VIEW

ROOFING SYSTEM


05/067RS


REV:APPROVED BY: DATE:

version.

2. FLASHINGS SHALL BE CONFIGURED AND

INSTALLED IN A WATER TIGHT FASHION

PRIOR TO OUTSULATION INSTALLATION

APPLY AQUAFLASH® SYSTEM OR FLASHING

TAPE™ AT WALL/SLEEVE TRANSITION.

1.









ROOF FLASHING AND COUNTER

FLASHING, BY OTHERS


W/CLOSED CELL BACKER ROD,

BY OTHERS

Outsulation® System Parapet/Wall Termination


DRYVIT FINISH

OUTSULATION SYSTEM



FLASHING SLEEVE SHOWN

IN EXPLODED VIEW

METAL COPING FLASHING

AT PARAPET WALL


ALUMINUM REGLET

OS 0.0.16


OS 0.0.17


Soffit With Fascia Extended Drip










08/0612DAW









BE INDICATED ON CONTRACT DRAWINGS. ®

version.

1.and Dryvit specifically disclaims any liability for the use of this

25 MM (1") MAX.

®Outsulation System

DRYVIT ADHESIVE

DRYVIT REINFORCING

MESH EMBEDDED IN

DRYVIT BASE COAT

DRYVIT FINISH

EPS INSULATION

FRAMING

SUBSTRATE


version.









1.

DRYVIT DETAIL

MESH® EMBEDDED

IN DRYVIT BASE COAT

OVERLAP 64 MM (2 1/2") MIN.

Soffit Router Cut Drip®Outsulation System


19 MM (3/4") MIN.

DRYVIT REINFORCING

MESH EMBEDDED IN

DRYVIT BASE COAT

DRYVIT FINISH

EPS INSULATION

DRYVIT ADHESIVE

SUBSTRATE

FRAMING

OS 0.0.18



08/0612DAW











®

APPROVED BY: DATE:REV:





DAW 08/0612











®

version.

1.









Outsulation System®Soffit With Expansion Joint




19 MM (3/4") MIN.

DRYVIT FINISH



SUBSTRATE

DRYVIT ADHESIVE

EPS INSULATION




OS 0.0.19

version.

3. REFER TO DRYVIT PUBLICATION DS 173, FOR

APPLICATION ON EXTERIOR SOFFITS.

1. SOFFITS WITHOUT EPS INSULATION REQUIRE

EXPANSION JOINTS EVERY 6.096 M (20 FT).

2.

Soffit - Uninsulated


Outsulation®System

DRYVIT FINISH



DRYVIT ADHESIVE

EPS INSULATION



SUBSTRATE

OS 0.0.20















BE INDICATED ON CONTRACT DRAWINGS. ®


25 MM (1") MAX.

SUBSTRATE




EMBEDDED IN BASE COAT


08/0612DAW















®


203 MM (8") MIN.

SEE NOTES 2 AND 3

NOTE:

08/0612DAW

version.

3. DO NOT LAP REINFORCING MESH WITHIN

203 MM (8") OF A CORNER.





2. DOUBLE WRAP OUTSIDE CORNERS WITH

REINFORCING MESH OR USE CORNER MESH.1.





Outside CornersROutsulation SystemDryvit products is the responsibility of the project's design


203 MM (8") MIN.

SEE NOTES 2 AND 3

SUBSTRATE

DRYVIT FINISH



DRYVIT ADHESIVE

EPS INSULATION

OS 0.0.21


DRYVIT BASE COAT

NOTE:professional. All systems must comply with local building codes and

08/0612DAW











APPROVED BY:

®

REV: DATE:

version.

1.








203 MM (8") MIN.

Outsulation System® Outside Corner - High Impact



DRYVIT FINISH

PANZER® 15 OR 20

REINFORCING MESH

DRYVIT STANDARD OR STANDARD

PLUS REINFORCING MESH OVERLAP

MIN. 203 MM (8") AT CORNER

DRYVIT CORNER MESH

DRYVIT ADHESIVE

EPS INSULATION

DRYVIT BASE COAT

SUBSTRATE

OS 0.0.22


BY OTHERS

OPTIONAL SECONDARY

SEAL, BY OTHERS





WRAP DRYVIT DETAIL

MESH® 51 MM (2") MIN.

AT UNDERSIDE OF EPS

(SEE NOTE 2)



19 MM (3/4") MIN.










08/0613DAW










version.

®


AS AN OPTION, THE REINFORCED

BASE COAT EDGE WRAP MAY BE

EXTENDED ONTO THE CONCRETE

EDGE AND/OR FRAMING.

1. 2.

Structural Expansion Joint



®Outsulation System

EPS INSULATION

DRYVIT ADHESIVE

FRAMING

SUBSTRATE

DRYVIT

OUTSULATION

SYSTEM

DRYVIT FINISH

BY OTHERS

SOLID SUBSTRATE

OS 0.0.23






1.and Dryvit specifically disclaims any liability for the use of this



®Outsulation System Outsulation Expansion Joint - Dissimilar Substrates




CLOSED-CELL BACKER ROD, BY OTHERS

19 MM (3/4") MIN.

DRYVIT FINISH



SUBSTRATE

BY OTHERS

FRAMINGSOLID SUBSTRATE

OS 0.0.24

DRYVIT ADHESIVE


EMBEDDED IN DRYVIT BASE COATWRAP DRYVIT DETAIL MESH®


EPS INSULATION

DRYVIT

OUTSULATION

SYSTEM


08/0612DAW










version.

®




DRYVIT ADHESIVE

NOTE: professional. All systems must comply with local building codes and

08/0614RS










version.

APPROVED BY:

®

REV: DATE:

2. AS AN OPTION, THE REINFORCED BASE

COAT EDGE WRAP MAY BE EXTENDED ONTO

THE FRAMING.

1.









Outsulation System®Structural Expansion Joint - Inside Corner



FRAMING



(SEE NOTE 2)

19 MM (3/4") MIN.

OPTIONAL SECONDARY

SEAL, BY OTHERS

DRYVIT-COMPATIBLE SEALANT WITH




DRYVIT FINISH

EPS INSULATION

DRYVIT ADHESIVE

SUBSTRATE

OS 0.0.25

DRYVIT OUTSULATION SYSTEM BY OTHERS

REV:APPROVED BY: DATE:

1. 2. AS AN OPTION, THE REINFORCED BASE

COAT EDGE WRAP MAY BE EXTENDED

ONTO THE FRAMING.


08/0613RS


















version.

®


Structural Expansion Joint - Outside Corner


Outsulation System®




EPS INSULATION

DRYVIT FINISH

DRYVIT ADHESIVE

OPTIONAL SECONDARY

SEAL, BY OTHERS





(SEE NOTE 2)

19 MM (3/4") MIN.



SUBSTRATE

OS 0.0.26

AS AN OPTION, THE REINFORCED BASE

COAT EDGE WRAP MAY BE EXTENDED ONTO

THE FRAMING. any project. The project design professional determines, in its sole





1. 2.and Dryvit specifically disclaims any liability for the use of this



EPS INSULATION



PenetrationsOutsulation SystemThe architecture, engineering and design of the project using the


®

DRYVIT FINISH

DRYVIT ADHESIVE

DRYVIT DEMANDIT OR COLOR PRIME


SUBSTRATE



(SEE NOTE 2)

OPTIONAL SECONDARY SEAL,

BY OTHERS



DRYVIT-COMPATIBLE SEALANT WITH


19 MM (3/4") MIN.

OS 0.0.27


OPTIONAL SECONDARY SEAL

19 MM (3/4") MIN.


08/0612DAW










version.

®










Outsulation System®Sign Attachment



12.7 MM (12") MIN.

DRYVIT REINFORCING

MESH EMBEDDED IN

DRYVIT BASE COAT

DRYVIT FINISH

SIGN FIXTURE

FRAMING

PIPE SLEEVE SET IN SEALANT

SCREW OR BOLT ATTACHMENT

TO BUILDING FRAMING OR

STRUCTURAL SUBSTRATE

BEARING WASHER

professional. All systems must comply with local building codes andPERIMETER OF PIPE SLEEVE IS CAULKED TO

PREVENT WATER ENTRY INTO WALL.

NOTE:

1.

05/0612DAW

version.

APPROVED BY:

®

DATE:REV:

DRYVIT-COMPATIBLE

SEALANT AND BOND

BREAKER TAPE, BY OTHERS

EPS INSULATION

BLOCKING OR STRUCTURAL

SUBSTRATE AS REQUIRED

DRYVIT ADHESIVE

SUBSTRATE

OS 0.0.28

DRYVIT

OUTSULATION

SYSTEMBY OTHERS

BY OTHERS

OS 0.0.29

1.4 KG/M² (2.5 LBS/YD²) OR 1.8 KG/M²

(3.4 LBS/YD²) GALVANIZED EXPANDED

METAL LATH (BY OTHERS)

ATTACH METAL LATH TO STRUCTURAL

FRAMING USING APPROPRIATE

FASTENERS (BY OTHERS)



DRYVIT ADHESIVE (KEYED INTO LATH)

SUBSTRATE

EPS INSULATION


DRYVIT FINISH

METAL OR

WOOD STUDS

DRYVIT ADHESIVE (KEYED INTO LATH)



1.4 KG/M² (2.5 LBS/YD²) OR 1.8 KG/M²

(3.4 LBS/YD²) GALVANIZED EXPANDED

METAL LATH (BY OTHERS)












Outsulation Applied Over Metal Lath

1. DRYVIT RECOMMENDS THAT GROUND









version.


12DAW 08/06

DRYVIT FINISH

Outsulation System

NOTE:

®

BRICK, MASONRY

OR CONCRETE

CONSTRUCTION

EPS INSULATION

®

ATTACH METAL LATH TO SUBSTRATE

USING APPROPRIATE FASTENERS OR

ANCHORS (BY OTHERS)

12

2. SLOPE BOTTOM EDGE OF REVEAL FOR

POSITIVE DRAINAGE.

1. DRYVIT RECOMMENDS THAT GROUND










DAW

version.

®


08/06









Aesthetic RevealsOutsulation System

NOTE:



®

DRYVIT DETAIL MESH®


19 MM (3/4") MIN.

EPS INSULATION




DRYVIT FINISH

FRAMING MEMBER

DRYVIT ADHESIVE

SUBSTRATE

OVERLAP 64 MM (2 1/2")

OS 0.0.30

BY OTHERS

1. MAXIMUM THICKNESS OF EPS BUILT OUT

SHAPES SHALL NOT EXCEED 305 MM (12

INCHES) AT ANY POINT MEASURED FROM THE

SUBSTRATE

version.

PERCENTAGE OF WALL AREA COVERED BY

EPS FOAM SHAPES IN EXCESS OF 102 MM (4

IN.) IN THICKNESS SHALL NOT EXCEED 15%

®

REV: DATE:APPROVED BY:

05/0612DAW











EPS INSULATION

DRYVIT FINISH

DRYVIT ADHESIVE

OVERLAP 64 MM (2 1/2")

Outsulation SystemNOTE:

® Projecting Graphics





LAPPED 64 MM (2 1/2") MIN.

SUBSTRATE

DRYVIT

OUTSULATION

SYSTEM



DRYVIT FINISH

EPS INSULATION

DRYVIT ADHESIVE

SUBSTRATE

OS 0.0.31

SUBSTRATE



Recessed Graphics





LAPPED 64 MM (2 1/2") MIN.

Outsulation SystemNOTES:

®

DRYVIT ADHESIVEEPS INSULATION

BY OTHERS

DRYVIT

OUTSULATION

SYSTEM

OVERLAP 64 MM (2 1/2") MIN.

19 MM (3/4") MIN.

DRYVIT FINISH

DRYVIT FINISH



EPS INSULATION

DRYVIT ADHESIVE

SUBSTRATE

OS 0.0.32

standards. This detail is for general information and guidance only1. SLOPE BOTTOM EDGE OF HORIZONTAL

RECESSES FOR POSITIVE DRAINAGE








version.


11DAW 05/06

®

FLASHING NO. 1, BY OTHERS,

EXTEND UP BEHIND FLASHING

NO. 2 76 MM (3") MIN.

REFER TO OS 0.0.34 FOR DECK

CUTAWAY DETAIL.

THESE DETAILS DO NOT APPLY TO

CANTILEVERED DECKS. CANTILEVERED DECKS

REQUIRE JOB SPECIFIC FLASHING DETAILS.


version.


05/066DAW

®

2. WHEN FLASHING NUMBER 1 IS IN PLACE, EPS

WILL NEED TO BE PRE WRAPPED WITH BASE

COAT AND MESH.

of any project. The project design professional determines, in its sole





and Dryvit specifically disclaims any liability for the use of

this detail and for the architecture, design, engineering or workmanship


WRAP DRYVIT DETAIL MESH® 51 MM

(2") MIN. AT BACKSIDE OF EPS BOARD

SUBSTRATE

Outsulation® SystemNOTE:

1. 3.The architecture, engineering and design of the project using the


Termination at Deck - Section

64 MM (2-1/2") MIN.



25 MM (1") MIN.



FLASHING NO. 3, BY OTHERS, EXTEND UP

BEHIND EPS INSULATION 76 MM (3")

WOOD SUPPORT STRIP

WOOD DECK FRAMING

FLASHING NO. 2, BY OTHERS, EXTEND UP

BEHIND FLASHING NO. 3 76 MM (3") MIN.

51 MM (2") MIN.

WOOD DECK BOARDS

DRYVIT FINISH

OS 0.0.33

DRYVIT ADHESIVE

EPS INSULATION

DECK BOARD


THESE DETAILS DO NOT APPLY TO

CANTILEVERED DECKS. CANTILEVERED

DECKS REQUIRE JOB SPECIFIC FLASHING

DETAILS.

version.


05/066DAW

®

51 MM

(2") MIN.

DRYVIT COMPATIBLE

SEALANT WITH BOND

BREAKER, BY OTHERS

OS 0.0.34

REFER TO OS 0.0.33 FOR DECK SECTION DETAIL.2.of any project. The project design professional determines, in its sole





and Dryvit specifically disclaims any liability for the use of

this detail and for the architecture, design, engineering or workmanship


Outsulation® SystemNOTES:

1.The architecture, engineering and design of the project using the


Termination at Deck - Cut Away

END JOIST

FLASHING NO. 2,

BY OTHERS

FLASHING NO. 1,

BY OTHERS 51 MM (2") MIN.

FLASHING NO. 3, BY

OTHERS TURNED DOWN

OVER END JOIST

METAL FLASHINGS ARE 254 MM (10") X 51 MM

(2") LONGER THAN THE EXPOSED PORTION OF

THE ROOFING SHINGLE AND ARE BENT IN HALF

TO ALLOW FOR TWO 127 MM (5") LEGS.

ALTHOUGH NOT SHOWN, METAL FLASHINGS ARE

STEP FLASHED (INTERWOVEN) WITH ROOFING

SHINGLES.












version.

EXTEND DIVERTER FLASHING

(KICKOUT) A MINIMUM OF 25 MM

(1") BEYOND FACE OF SYSTEM.

3. EXTEND ROOFING UNDERLAYMENT

127 MM (5") UP VERTICAL WALL

BEHIND METAL FLASHING.

DAW 05/063


2. ROOF DIVERTER TO BE MADE FROM

CORROSION RESISTANT MATERIAL MIN.

24 GAGE WITH WATER TIGHT SEAMS.

®

ROOF DIVERTER FLASHING,


ROOF STEP FLASHING,

BY OTHERS

ROOFING UNDERLAYMENT,


Termination at Sloped Roof

GUTTER SYSTEM SLOPED

AWAY FROM WALL

(6")

Outsulation® SystemNOTE:

4.1.

(12")305 MM

152 MM

152 MM(6")

110

ROOF DIVERTER

(NOTE 2)

100

DRYVIT FINISH

ROOFING SHINGLES

51 MM (2") MIN.

EPS INSULATION



SUBSTRATE

FRAMING

OS 0.0.35


05/06

DATE:

1DAW

APPROVED BY: REV:

®



version.






DRYVIT COMPATIBLE

SEALANT, BY OTHERS

Outsulation SystemDryvit products is the responsibility of the project's design



®Termination at Roof Stop Flashing

ROOF SHINGLES

GLUED TO FLASHING

51 MM (2") MIN.

102 MM (4") MIN.

SHINGLES

ROOF STOP FLASHING,

BY OTHERS

ROOF/WALL FLASHING,

BY OTHERS

FASCIA BOARD

OS 0.0.36

WATER-RESISTIVE BARRIER

EXTENDED BEHIND FLASHING,

BY OTHERS


RS 0 05/08

version.



ABNORMAL STRESS, HIGH TRAFFIC, OR DELIBERATE

IMPACT HAVE THE BASE COAT REINFORCED WITH

PANZER® MESH PRIOR TO STANDARD™ OR

STANDARD PLUS™ MESH. LOCATION OF HIGH

IMPACT ZONES SHOULD BE INDICATED ON

CONTRACT DRAWINGS.


1.




TAPE™ MAY BE USED LIEU OF DRYVIT

AQUAFLASH SYSTEM.is best suited for the project. Use of a functionally equivalent detail






standards. This detail is for general information and guidance only2.

NOTE:

Horizontal Joint At Stone Veneer



STONE VENEER SYSTEM, BY OTHERS

APPROVED SUBSTRATE

EPS INSULATION BOARD NOTCHED TO

ACCOMMODATE FLASHING

DRYVIT ADHESIVE


ON SURFACE(S) TO RECEIVE SEALANT

CONTINUOUS FLASHING, BY OTHERS

SEALANT WITH BOND

BREAKER, BY OTHERS

DRYVIT COMPATIBLE SEALANT WITH CLOSED

CELL BACKER ROD, BY OTHERS

19 MM (3/4") MIN.

DRYVIT FINISH




51 MM (2") MIN. AT BACKSIDE OF EPS

DRYVIT AQUAFLASH®

SYSTEM (SEE NOTE 2)


OS 0.0.37


Documents

OUTSULATION - Dryvittest.dryvit.com/fileshare/doc/us/detail/ds107.pdfreinforced with panzer® mesh prior to standard mesh™ or standard plus mesh™. location of high impact zones