SoundSpot TM

SoundStand TM ST-90, ST-95

SoundCenter TM C-5

SoundSub TM IS-9A, RS-91A, RS-10A

SoundSub TM RS 91-P

Owner's Manualand

Installation Instructions

Owner's Manualand

Installation Instructions

l

l

l

l

l

ContentsImportant Notes

The SoundSpot TM Range

SoundSpot TM

SoundStand TM ST-90, ST-95

SoundCenter TM C-5

SoundSub TM IS-9A, RS-91A, RS-10A

SoundSub TM RS 91-P

Thank you for choosing Morel loudspeakers

Your speakers have been handcrafted by Morel from the highest-quality materials and components. Utmost attention and care havebeen devoted to every detail of the design and construction, toensure your long-lasting enjoyment of the product.

The more you play, the better the sound

The sound quality of all speakers improvesafter at least 48 hours of playing time.This is needed as a breaking-in and period forthe moving parts of a new speaker.

The usage of quality cables and connectorscan improve performance. A good speakercable connection requires ample surface-areaand contact-area pressure. We recommend thatyou consult your dealer for the most suitablecables to match your system and budget.

Speakers PlacementHome Theater Stereo

SW

B

SW

CENTER

A

SW

CENTER

The SoundSpotTM Home Theater Range

APPLAUSE

SUPRA

VITRA

SPIRO

EVIT

STREAM

METRO

COMPA

NOVA

BEAT

Five SoundSpotTM SA-2, SoundSubTM IS-9A

Four SoundSpotTM SA-2,SoundCenterTM C-5, SoundSubTM IS-9A

Two SoundSpotTM SA-2 front, Two SoundSpotTM SI-2 rear,SoundCenterTM C-5, SoundSubTM IS-9A

Four SoundSpotTM SI-2,SoundCenterTM C-5, SoundSubTM IS-9A

Two SoundSpotTM BI-2 front, Two SoundSpotTM BI-1 rear,SoundCenterTM C-5, SoundSubTM RS91-A (RS-10A)

Five SoundSpotTM SI-2,SoundSubTM RS-91A (RS-10A)

Three SoundSpotTM SI-2 front & center, Two SoundSpotTM LI-1 rear,SoundSubTM RS-91A (RS-10A)

Two SoundSpotTM SA-2 front, Two SoundSpotTM LI-1 rear,SoundCenterTM C-5, SoundSubTM RS-91A (RS-10A)

Five SoundSpotTM LI-1, SoundSubTM RS-91A (RS-10A)

Five SoundSpotTM BI-1, SoundSubTM RS-91A (RS-10A)

The SoundSpotTM Stereo Range

VIVACE

TRIO

Two SoundSpotTM SA-2, SoundSubTM RS-91P

Two SoundSpotTM SI-2, SoundSubTM RS-91P

Thank you for choosing Morel's SoundSpotTM. These award-winning speakers are unique in design and construction,offering extraordinary sound quality for both stereo and hometheatre applications in an attractive design.

SoundSpotTM

The SoundSpotTM speakers deliver a full and rich sound, but theirsize limits their ability to reproduce low-frequency bass notes,which require massive air movement. For a more full-bodied,dynamic sound across the entire frequency range, werecommend that you include Morel's subwoofer in your system.

Speaker PlacementThe SoundSpotTM speakers offer many installationpossibilities - they can be wall-mounted (fig. A or B),hung from the ceiling (fig. C), placed on a shelf or TVtop (fig. D), or fitted onthe specially designed(optional) ST-90 orST-95 floor stands(see p. 8).

A

B

C

D

Mounting the SoundSpotTM Speakers

The SoundSpotTM speakersare equipped with apivoting base that turns 180°.

To change the orientation of the base, to bestconceal the base in the selected mounting option,loosen the screw that locks the base position (locatedunder the base), rotate the base a full 180°and firmly tighten the screw.

Snap on the rubber footing

To mount your SoundSpotTM speaker on a ceiling or wall, firstchoose the location of the speaker and mark the precise spotwhere you will drill a hole to line up with the hole in the speakerbase. Next drill a hole in the wall using a7mm (1/4”) bit, and insert the plastic plug.Attach the speaker using the fixing screw.Cover the screw head with the plasticscrew cover provided.

Finally, adjust the speaker angle until the speaker is directedtoward the listening area, and lock it in place.

7mm1/4”

To mount your SoundSpotTM speakers onthe floor stand, see page 8.

ST-95

Insert the tapered tubeinto the cone in the base.

ST-90Next, fasten the screw tight withthe supplied Allen wrench.

SoundSpotTM ST-90, ST-95Installation Instructions (optional units)

Carefully fasten the tapered tube to the base.Make sure that the tube is perpendicular tothe base. Do not use mechanical tools orexcessive force. If you are unable to screw thetube completely into the base and eliminate thegap between the two parts, simply unscrewthe tube and repeat the process with thetube positioned precisely perpendicular.

To protect delicate surfaces usethe supplied rubber spikes andpress them onto the stands in sixdifferent locations.

Slip the speaker cablethrough the hollow tube,and out of the openingnear the top of the tube(under the bolt).

Finally, connect the speaker to the stand byremoving the speaker base (fig. A) andinserting the exposed joint into the stand tube(fig. B). Secure the bolt (fig. C), locking thespeaker to the stand.

To complete the setup, connect the speaker cableto the speaker's input terminals, following theinstallation instructions in your speaker manual.

ST-90, ST-95

ST-95ST-90

CB

AA

Caring for the SoundSpotTM SpeakersTo protect the speaker components, avoid operating thespeaker in extreme humidity or adverse temperatureconditions.

Unplug the electrical connection of theamplifier before making any connections.

Amplifier Connection

Regardless of your speaker setting or your amplifier's ratedpower capacity, do not operate the speakers at full outputlevels (highest volume), as the high levels of distortiongenerated by amplifiers at full output may damage your speakers.

For each speaker, connect the red or (+) output terminal onyour amplifier to the red input terminal on the speaker andconnect the black or (-) output terminal on the amplifier to theblack input terminal on the speaker.

LARGE, SMALL Speaker Amplifier SettingAC3, Dolby surround sound amplifiers have a speaker settingoption for large or small speakers.

This setting option is made to protect small speakers by filteringlow frequency signals, which may harm the speaker at highpower out put.

The following setting is needed for your speakers:LI-1, BI-1 set to small speaker option.All other speakers can be set to large speaker option.

Stereo ModelsThe SoundSpotTM SA-2, SI-2 and BI-2 stereo models aredesigned for direct connection to your amplifier and do notrequire a filtered output.

SoundCenterTM

Speaker PlacementThe SoundCenterTM C-5 speaker should be positioned as closeto your TV screen as possible. The speaker is magneticallyshielded to prevent screen distortions.

Thank you for choosing Morel's SoundCenterTM C-5. This highperformance center speaker is designed to provide amemorable home theater experience.

The center speaker plays a vital role in the home theatersystem, reproducing most of the front channel information in amovie soundtrack. Placed directly above or below the TV, thecenter speaker creates the central soundstage, positioningdialogue on the screen, just like in a commercial theater.

Amplifier ConnectionUse an amplifier of at least 30 watts per channel. It isacceptable to use an amplifier with greater power output thanthe power handling capacity of your speakers.

Regardless of your amplifier's rated power capacity,do not operate the speakers at full output levels(highest volume), as the high levels of distortiongenerated by amplifiers at full output may damageyour speakers.

Connect the red or (+) centre speaker output terminal of youramplifier to the red input terminal on the speaker, and connectthe black or (-) centre speaker output terminal on the amplifierto the black input terminal on the speaker.

Unplug the electrical connection of the amplifierbefore making any connections.

Caring for the SoundCenterTM SpeakersTo protect the speaker's components, avoid operating thespeaker in extreme humidity or adverse temperatureconditions.

Protect you speaker from exposure to water.

SoundSub TM

IS-9A, RS-91A, RS10ASafety Instructions

Read The InstructionsPlease read all safety and operating instructionscarefully before using or connecting your SoundSubTM

subwoofer.

Voltage Selector SwitchBefore operating, adjust the position of the voltageselector switch to 115V or 230V, according to thepower supply in your country.

Output LevelBefore operating, set the output level to minimum.

Power SwitchBefore plugging in the AC power cord, set the powerswitch to off.

Water and MoistureTo reduce the risk of fire or electric shock, do notexpose this appliance to rain or moisture.

ServicePlease do not attempt to service the appliance beyondthe steps described within the operating instructions.All other servicing should be referred to a qualifiedservice technician.

Speaker PlacementIn designing the subwoofer, we have made every effort tomake it unobtrusive in the environment, by its slim cabinetdesign. Unlike surround or stereo speakers, which must beplaced to project directly to the listeners' ears, the subwoofermoves all the air in the room and can be placed whereverconvenient. The subwoofer can even be hidden behind theTV stand or next to any furniture.

Thank you for choosing Morel's SoundSubTM Subwoofer.

The SoundSubTM RS-91A, RS10A and IS-9A are activesubwoofers (IS-9A is built of two 9" woofers), driven by a high-quality amplifier that is AC-3 compatible. Designed to augmentthe SoundSpotTM satellite speakers in the low bass frequencyrange, the SoundSubTM will enhance any home theater systemwith a well-controlled, accurate bass.

Connecting The SoundSubTM

1.1 Main Power switchThe new amplifier will have its main breaker switch at the bottomleft corner, next to the power cord inlet. It consists of an ON/OFFswitch.The main power switch has to be in the ON position in-order forthe unit to become operational.

1.2 Auto power switchIn the upper left there is a power switch. If AUTO position isselected, the sub will become operational as soon as theSoundSubTM will receive an audio signal. It will be turned offseveral minutes after the audio signal is switched off. At the ON position the SoundSubTM will become operationalindefinitely, or until the AUTO position is selected.

RS-91A, RS10A

POWERON AUTO

LINE

OUT IN

PHASE CROSSOVER LEVEL

R+

R-

R+

R-

L+

L-

L+

L-

HIGH LEVEL IN

HIGH LEVEL OUT

0 180 40 160 MIN MAX3

4

5

6

7

L

R

L

R1.2 2

LINE

HIGH LEVEL OUT

6

7

8

PHASE1800

OUTINL

R

L

R

CROSSOVER

40 160

LEVEL

MIN MAX

230V 115V

POWERONAUTO

HIGH LEVEL IN

R+

R-

L+

L-

R+

R-

L+

L-

2

54

1.2

3

IS-9A

8

1.1

1.1

offon 230V 115V

off

on

2. RCA jacksThe input terminals connect to the subwoofer (line level)outputs of an amplifier. The output terminals provide an inputbypass for connection to a second subwoofer, or any otherpurpose.

3. PHASE controlThe phase control allows phase adjusting of the subwoofer tomatch that of the other speakers in your home theater system.With the system turned on, turn the phase control first to oneextreme then to the other, and leave it in the position at whichthe bass level in your room sounds strongest and deepest.

4. CROSSOVER controlThe crossover control determines the range of frequencies yoursubwoofer will reproduce. When turned to 40Hz, the subwooferwill only issue the lowest bass frequencies. As you turn theknob towards 160Hz, the subwoofer will reproduce a widerfrequency range. When the crossover control is adjustedcorrectly, the subwoofer, together with the other speakers inyour system, reproduces the entire range of bass.

5. LEVEL controlThe level control adjusts the sound level of your subwoofer. Setto provide the required level of bass relative to the soundreproduced by the other speakers in the system. The soundlevel reproduced by the subwoofer will change as you modifythe volume control setting on your amplifier, maintaining therelative level set by this control.

6. BINDING POST terminalsThese are input terminals for connection to the high-leveloutputs of an amplifier (parallel to the front speaker connection).Output terminals provide a filtered output to surround speakers.See the Connection Guidelines for details.

7. VOLTAGE SELECTOR switchBefore operating, adjust the position of the voltage selectorswitch to 115V or 230V, according to the power supply in yourcountry.

8. AC outletPower supplied through this outlet is turned on and off by thePOWER switch.

Before making connections it is advisable toensure that all AC power cords of the componentsyou are interconnecting are unplugged from thewall outlets during the hookup process.

Connection Guidelines

Connection Through the Line-Level (RCA) InputsUse this connection option if your amplifier has a low frequency exit(LFE) subwoofer output, or pre-amp outputs (all AC3 or DolbySurround amplifiers have such an output). Connect the two LFE (orPRE OUT) outputs (for left and right channels), to the two LINE INinputs in your SoundSubTM, using an RCA (interconnect) cable pair.If your amplifier has only a single subwoofer output, then connectthis output from your amplifier to just one of the LINE IN inputsin your SoundSubTM.

Connection Through the High-Level (BINDING POST) InputsUse this connection option if your amplifier does not have anLFE output (this is the case, for instance, if you are using aPrologic or hi-fi amplifier). Using a speaker cable: connect thered or (+) right speaker output terminal of your amplifier to theR+ terminal on your subwoofer, and connect the black or (- )rightspeaker output terminal on the amplifier to the R- terminal onthe subwoofer. Repeat the process for the left speaker,connecting the red or (+) left speaker output terminal

of your amplifier to the L+ terminal on your subwoofer, and theblack or (-) left speaker output terminal on the amplifier to theL- terminal on the subwoofer. Your subwoofer should now beconnected in parallel to your front or stereo speakers.

Using the Line-Level (RCA) OutputsThe line-level output terminals provide an output bypass fromyour subwoofer. Use these outputs to connect anothersubwoofer in parallel to the SoundSubTM, or for other purposes.

Using the High Level (BINDING POST) OutputsThe high level output terminals offer a filtered output for satellitespeakers. The filtered output is clear of low frequency signals,thus protecting the satellite speakers from overloading that maydamage them. Note that Morel's SoundSpotTM speakers do notrequire these exits, and should be connected directly to youramplifier for optimal sound quality (See page 8 for amplifierconnection).

SoundSubTM

RS 91-PThank you for choosing Morel's SoundSubTM Subwoofer.

The SoundSubTM RS 91-P are passive subwoofers, designedto complement your system in the low bass range,reproducing frequencies below 200 Hz. They are ideal forcomplementing a stereo system with small speakers, orsatellite speakers that are incapable of reproducing the lowfrequency notes due to their size.

The deep, dynamic bass reproduced by the SoundSubTM

subwoofers adds an important dimension to the listeningexperience, elevating the level of realism and boosting thelistener's emotional involvement.

Speaker PlacementThe optimal location for the SoundSubTM subwoofers is in frontof the listener, in between the two stereo speakers. TheSoundSubTM can also be placed to the side of the listener, butcaution is required, as moving the subwoofer too far back mayimpair the stereo imaging and acoustical balance of the system.

For optimal performance, we recommend you position thesubwoofer so that it is at least 10 cm (4") from the wall behindit. The speaker will sound better if not positioned in a corner.

The back panel of the SoundSubTM subwoofer offers two pairsof inputs, coloured red and black, respectively. Connect thesubwoofer to both stereo channels, using the top pair for onechannel and the lower pair for the second channel:

Connect the red or (+) right speaker output terminal of youramplifier to the top red terminal on your subwoofer, and connectthe black or (-) right speaker output terminal on the amplifier tothe top black terminal on the subwoofer.

Repeat the process for the left speaker, connecting the red or(+) left speaker output terminal of your amplifier to the lowerred terminal on your subwoofer, and the black or (-) left speakeroutput terminal on the amplifier to the lower black terminal onthe subwoofer.

Your subwoofer should now be connected in parallel to yourfront or stereo speakers.

Amplifier ConnectionBefore making connections it is advisable toensure that all AC power cords of the componentsyou are interconnecting are unplugged from thewall outlets during the hookup process.

STEREO AMPLIFIERSPEAKERS OUTPUT

L

+ –

R

– +

– +

– +

– + – +

R L

SPEAKER SPEAKER

SUBWOOFER INPUT TERMINAL

Caring for Your SoundSubTM SubwoofersTo assure long-lasting enjoyment from your subwoofers, werecommend that you follow a few guidelines, which areappropriate for every speaker system:

Do not increase the volume beyond the capabilities of youramplifier. Setting the volume to levels that your amplifier cannotsustain will result in clipping that produces audible sounddistortion and may damage the speakers.

Note that a weaker amplifier can potentially cause moredamage to speakers than amplifiers with a high-power rating. Ifyou intend to listen to music at high volume levels, ensure thatthe output power of your amplifier is at least as high as thecapacity of your speakers.

A second option, although we do not recommend it, is to connectthe stereo speakers to the subwoofer instead of to the amplifier,making sure to make consistent right and left channelconnections.

Morel Reserves the right to amend details of the specification without notice in line with technical developments.

All rights reserved to morel 2002

www.morelhifi.com