OWNER’S MANUAL - Honda

SH125i/SH

150i

SH125i/SH150i

XXX.XXXX.XX.LPRINTED IN XXXXX

OWNER’S MANUAL

32K0RA0000X32-K0R-A000

EN

This manual should be considered a permanent part of the vehicleand should remain with the vehicle when it is resold.

This publication includes the latest production information availablebefore printing. Honda Motor Co., Ltd. reserves the right to makechanges at any time without notice and without incurring anyobligation.

No part of this publication may be reproduced without writtenpermission.

The vehicle pictured in this owner’s manual may not match youractual vehicle.

© 2019 Honda Motor Co., Ltd.

20200114224232_32K0RA000_eng_BOOK Page 1 Tuesday, January 14 2020 22:55:25 JST

WelcomeCongratulations on your purchase of a newHonda vehicle. Your selection of a Hondamakes you part of a worldwide family ofsatisfied customers who appreciate Honda'sreputation for building quality into everyproduct.

To ensure your safety and riding pleasure:● Read this owner's manual carefully.● Follow all recommendations and

procedures contained in this manual.● Pay close attention to safety messages

contained in this manual and on thevehicle.

● The following codes in this manualindicate each country.

● The illustrations here in are based on theSH150AD ED type.

Country CodesCode CountrySH125ADED, Ⅱ ED, Ⅲ ED,Ⅳ ED, Ⅴ ED European direct sales

SH150ADED, Ⅱ ED, Ⅲ ED,Ⅳ ED, Ⅴ ED European direct sales

*The specifications may vary with each locale.


A Few Words About SafetyYour safety, and the safety of others, is veryimportant. Operating this vehicle safely is animportant responsibility.To help you make informed decisions aboutsafety, we have provided operatingprocedures and other information on safetylabels and in this manual. This informationalerts you to potential hazards that couldhurt you or others.Of course, it is not practical or possible towarn you about all hazards associated withoperating or maintaining a vehicle. You mustuse your own good judgement.

You will find important safety information in avariety of forms, including:● Safety labels on the vehicle● Safety Messages preceded by a safety alert

symbol and one of three signal words:DANGER, WARNING, or CAUTION.These signal words mean:

3DANGERYou WILL be KILLED or SERIOUSLYHURT if you don’t follow instructions.

3WARNINGYou CAN be KILLED or SERIOUSLYHURT if you don’t follow instructions.

3CAUTIONYou CAN be HURT if you don’t followinstructions.

Other important information isprovided under the following titles:NOTICE Information to help you avoid

damage to your vehicle, otherproperty, or the environment.


Contents

Vehicle Safety P. 2

Operation Guide P. 18

Maintenance P. 74

Troubleshooting P. 114

Information P. 138

Specifications P. 152

Index P. 155


Safety Guidelines .................................................P. 3Image Labels.........................................................P. 6Safety Precautions.............................................P. 10Riding Precautions ............................................P. 11Accessories & Modifications...........................P. 16Loading ................................................................P. 17


This section contains important information for safe riding of your vehicle.Please read this section carefully.

Vehicle Safety

Safety GuidelinesFollow these guidelines to enhance your safety:● Perform all routine and regular inspections

specified in this manual.● Stop the engine and keep sparks and flame

away before filling the fuel tank.● Do not run the engine in enclosed or partly

enclosed areas. Carbon monoxide inexhaust gases is toxic and can kill you.

Always Wear a HelmetIt's a proven fact: helmets and protectiveapparel significantly reduce the number andseverity of head and other injuries. So alwayswear an approved helmet and protectiveapparel. 2 P. 10

Before RidingMake sure that you are physically fit, mentallyfocused and free of alcohol and drugs. Check

that you and your passenger are both wearingan approved helmet and protective apparel.Instruct your passenger on holding onto thegrab rail or your waist, leaning with you in turns,and keeping their feet on the footpegs, evenwhen the vehicle is stopped.

Take Time to Learn & PracticeEven if you have ridden other vehicles, practiceriding in a safe area to become familiar withhow this vehicle works and handles, and tobecome accustomed to the vehicle's size andweight.

Ride DefensivelyAlways pay attention to other vehicles aroundyou, and do not assume that other drivers seeyou. Be prepared to stop quickly or perform anevasive maneuver.


Safety GuidelinesVehicle Safety

3Continued

Make Yourself Easy to SeeMake yourself more visible, especially at night,by wearing bright reflective clothing, positioningyourself so other drivers can see you, signalingbefore turning or changing lanes, and usingyour horn when necessary.

Ride within Your LimitsNever ride beyond your personal abilities orfaster than conditions warrant. Fatigue andinattention can impair your ability to use goodjudgement and ride safely.

Don't Drink and RideAlcohol and riding don't mix. Even one alcoholicdrink can reduce your ability to respond tochanging conditions, and your reaction timegets worse with every additional drink. Don'tdrink and ride, and don't let your friends drinkand ride either.

Keep Your Honda in Safe ConditionIt's important to keep your vehicle properlymaintained and in safe riding condition.Inspect your vehicle before every ride andperform all recommended maintenance. Neverexceed load limits (2 P. 17), and do not modifyyour vehicle or install accessories that wouldmake your vehicle unsafe (2 P. 16).

If You are Involved in a CrashPersonal safety is your first priority. If you oranyone else has been injured, take time toassess the severity of the injuries and whether itis safe to continue riding. Call for emergencyassistance if needed. Also follow applicable lawsand regulations if another person or vehicle isinvolved in the crash.


Safety Guidelines

Vehicle Safety

4

If you decide to continue riding, first turn theignition switch to the (Off) position, andevaluate the condition of your vehicle. Inspectfor fluid leaks, check the tightness of critical nutsand bolts, and check the handlebar, controllevers, brakes, and wheels. Ride slowly andcautiously.Your vehicle may have suffered damage that isnot immediately apparent. Have your vehiclethoroughly checked at a qualified service facilityas soon as possible.

Carbon Monoxide HazardExhaust contains poisonous carbon monoxide, acolourless, odorless gas. Breathing carbonmonoxide can cause loss of consciousness andmay lead to death.

If you run the engine in confined or even partlyenclosed area, the air you breathe couldcontain a dangerous amount of carbonmonoxide.

Never run your vehicle inside a garage or otherenclosure.

3WARNINGRunning the engine of your vehiclewhile in an enclosed or even partiallyenclosed area can cause a rapid build-up of toxic carbon monoxide gas.

Breathing this colourless, odorless gascan quickly cause unconsciousness andlead to death.

Only run your vehicle's engine when itis located in a well ventilated areaoutdoors.


Safety GuidelinesVehicle Safety

5

Image LabelsThe following pages describe the labelmeanings. Some labels warn you ofpotential hazards that could cause seriousinjury. Others provide important safetyinformation. Read this information carefullyand don't remove the labels.

If a label comes off or becomes hard toread, contact your dealer for a replacement.

There is a specific symbol on each label.The meanings of each symbol and label areas follows.

Read instructions contained in Owner'sManual carefully.

Read instructions contained in Shop Manualcarefully. In the interest of safety, take thevehicle to be serviced only by your dealer.

DANGER (with RED background)You WILL be KILLED or SERIOUSLY HURT ifyou don't follow instructions.WARNING (with ORANGE background)You CAN be KILLED or SERIOUSLY HURT ifyou don't follow instructions.CAUTION (with YELLOW background)You CAN be HURT if you don't followinstructions.


Image Labels

Vehicle Safety

6

BATTERY LABELDANGER• Keep flame and spark away from the battery. Battery

produce explosive gas that can cause explosion.• Wear the eye protection and rubber gloves when handling

the battery, or you can get burned or lose your eyesight bythe battery electrolyte.

• Do not allow children and other people to touch a batteryunless they understand proper handling and hazards of thebattery very well.

• Handle the battery electrolyte with extreme care as itcontains dilute sulfuric acid. Contact with your skin or eyescan burn you or cause loss of your eyesight.

• Read this manual carefully and understand it before handlingthe battery. Neglect of the instructions can cause personalinjury and damage to the vehicle.

• Do not use a battery with the electrolyte at or below thelower level mark. It can explode causing serious injury.


Image LabelsVehicle Safety

7Continued

RADIATOR CAP LABELDANGERNEVER OPEN WHEN HOT.Hot coolant will scald you.Relief pressure valve begins to open at 108 kPa.

ACCESSORIES AND LOADING WARNING LABELWARNINGACCESSORIES AND LOADING• The safety stability and handling of this vehicle may be affected by the

addition of accessories and luggage.• Read carefully the instructions contained in user's manual and

installation guide before installing any accessory.• The total weight of accessories and luggage added to rider's and

passenger's weight should not exceed 180 kg (397 lb), which is themaximum weight capacity.

• The luggage weight must not exceed 14.5 kg (32 lb) under anycircumstances.

• The fitting of large fork-mounted or large handlebar mounted fairing isnot recommended.


Image Labels

Vehicle Safety

8

TYRE INFORMATION & CARGO LIMIT LABELFor your protection, always wear helmet, protectiveapparel.Cold tyre pressure:[Driver only]

Front 200 kPa (2.00 kgf/cm2, 29 psi)Rear 225 kPa (2.25 kgf/cm2, 33 psi)

[Driver and passenger]Front 200 kPa (2.00 kgf/cm2, 29 psi)Rear 225 kPa (2.25 kgf/cm2, 33 psi)

Cargo limit:Shopping hook 1.5 kg (3.3 lb)Centre compartment 10 kg (22 lb)Rear carrier 3 kg (6.6 lb)

FUEL LABELUnleaded petrol onlyETHANOL up to 10 % by volume


Image LabelsVehicle Safety

9

Safety Precautions● Ride cautiously and keep your hands on the

handlebar and feet on the floor.● Keep passenger's hands onto the grab rail

or your waist, passenger's feet on thefootpegs while riding.

● Always consider the safety of yourpassenger, as well as other drivers andriders.

Protective ApparelMake sure that you and any passenger arewearing an approved helmet, eye protection,and high-visibility protective clothing. Ridedefensively in response to weather and roadconditions.

# HelmetSafety-standard certified, high-visibility, correctsize for your head● Must fit comfortably but securely, with the

chin strap fastened.

● Face shield with unobstructed field of visionor other approved eye protection

3WARNINGNot wearing a helmet increases thechance of serious injury or death in acrash.

Make sure that you and any passengeralways wear an approved helmet andprotective apparel.

# GlovesFull-finger leather gloves with high abrasionresistance# Boots or Riding ShoesSturdy boots with non-slip soles and ankleprotection# Jacket and TrousersProtective, highly visible, long-sleeved jacketand durable trousers for riding (or a protectivesuit)


Safety Precautions

Vehicle Safety

10

Riding PrecautionsRunning-in Period

During the first 500 km (300 miles) of running,follow these guidelines to ensure your vehicle'sfuture reliability and performance.● Avoid full-throttle starts and rapid

acceleration.● Avoid hard braking.● Ride conservatively.

BrakesObserve the following guidelines:● Avoid excessively hard braking.

u Sudden braking can reduce the vehicle'sstability.

u Where possible, reduce speed beforeturning; otherwise you risk sliding out.

● Exercise caution on low traction surfaces.u The tyres slip more easily on such

surfaces and braking distances arelonger.

● Avoid continuous braking.u Repeated braking, such as when

descending long, steep slopes canseriously overheat the brakes, reducingtheir effectiveness.

● For full braking effectiveness, operate boththe front and rear brakes together.


Riding PrecautionsVehicle Safety

11Continued

# Anti-lock Brake System (ABS)This model is equipped with an Anti-lock BrakeSystem (ABS) designed to help prevent thebrakes from locking up during hard braking.● ABS does not reduce braking distance. In

certain circumstances, ABS may result in alonger stopping distance.

● ABS does not function at speeds below 10km/h (6 mph).

● The brake levers may recoil slightly whenapplying the brakes. This is normal.

● Always use the recommended front/reartyres to ensure correct ABS operation.

# Wet or Rainy ConditionsRoad surfaces are slippery when wet, and wetbrakes further reduce braking efficiency.Exercise extra caution when braking in wetconditions.If the brakes get wet, apply the brakes whileriding at low speed to help them dry.

Parking● Park on a firm, level surface.● If you must park on a slight incline or loose

surface, park so that the vehicle cannotmove or fall over.

● Make sure that high-temperature partscannot come into contact with flammablematerials.

● Do not touch the engine, muffler, brakesand other high-temperature parts until theycool down.

● To reduce the likelihood of theft, always lockthe handlebar, lock the ignition switch(2 P. 51) and leave your vehicle while takingthe Honda SMART Key with you. Deactivatethe Honda SMART Key system if necessary.2 P. 46Use of an anti-theft device is alsorecommended.


Riding Precautions

Vehicle Safety

12

# Parking with the Side Stand or CentreStand

1. Stop the engine.2. Using the side stand

Push the side stand down.Slowly lean the vehicle to the left until itsweight rests on the side stand.Using the centre standTo lower the centre stand, stand on the leftside of the vehicle.Hold the left handle grip and the grab rail.Press down on the tip of the centre standwith your right foot and, simultaneously, pullup and back.

3. Turn the handlebar fully to the left.u Turning the handlebar to the right

reduces stability and may cause thevehicle to fall.

4. Turn the ignition switch to the (Lock)position (2 P. 44) and lock the ignitionswitch (2 P. 51).



13Continued

Left handle gripGrab rail

Centre stand

Refuelling and Fuel GuidelinesFollow these guidelines to protect the engine,fuel system and catalytic converter:● Use only unleaded petrol.● Use recommended octane number. Using

lower octane petrol will result in decreasedengine performance.

● Do not use fuels containing a highconcentration of alcohol. 2 P. 150

● Do not use stale or contaminated petrol oran oil/petrol mixture.

● Avoid getting dirt or water in the fuel tank.


Riding Precautions

Vehicle Safety

14

Honda selectable torque controlWhen the Honda selectable torque control(Torque Control) detects rear wheel spin duringacceleration, the system will limit the amount oftorque applied to the rear wheel.

Torque Control does not work duringdeceleration and will not prevent the rear wheelfrom skidding due to engine braking. Do notclose the throttle suddenly, especially whenriding on slippery surfaces.

Torque Control may not compensate for roughroad conditions or rapid throttle operation.Always consider road and weather conditions,as well as your skills and condition, whenapplying throttle.If your vehicle gets stuck in mud, snow or sand,it may be easier to free it by turning off theTorque Control temporarily.Temporarily turning off Torque Control alsomay help you maintain control and balancewhen riding on off-road terrain.

Always use the recommended tyres and theHonda Genuine Parts for drive system such asthe drive belt and weight rollers, to ensurecorrect Torque Control operation.



15

Accessories &ModificationsWe strongly advise that you do not add anyaccessories that were not specifically designedfor your vehicle by Honda or makemodifications to your vehicle from its originaldesign. Doing so can make it unsafe.Modifying your vehicle may also void yourwarranty and make your vehicle illegal tooperate on public roads. Before deciding toinstall accessories on your vehicle be certain themodification is safe and legal.

3WARNINGImproper accessories or modificationscan cause a crash in which you can beseriously hurt or killed.

Follow all instructions in this owner'smanual regarding accessories andmodifications.

Do not pull a trailer with, or attach a sidecar to,your vehicle. Your vehicle was not designed forthese attachments, and their use can seriouslyimpair your vehicle's handling.


Accessories & Modifications

Vehicle Safety

16

Loading● Carrying extra weight affects your vehicle's

handling, braking and stability.Always ride at a safe speed for the load youare carrying.

● Avoid carrying an excessive load and keepwithin specified load limits.Maximum weight capacity / Maximumluggage weight 2 P. 152

● Tie all luggage securely, evenly balancedand close to the centre of the vehicle.

● Do not place objects near the lights or themuffler.

3WARNINGOverloading or improper loading cancause a crash and you can be seriouslyhurt or killed.

Follow all load limits and other loadingguidelines in this manual.


LoadingVehicle Safety

17

Basic Operation Flow


Operation Guide

18

# Pre-ride Inspection (P.79)Carefully inspect your vehicle tomake sure that it is safe to ride.

# Acceleration (P.62)Apply throttle gradually.Obey the speed limit.

How to use basic features.• Instruments (P.22)• Indicators (P.40)• Switches (P.42)• Steering Lock (P.44)

# Starting the Engine (P.59)Start and warm the engine.Avoid revving the engine. # Starting the

Vehicle (P.62)

Before pulling away, indicateyour direction with the turnsignal switch, and check foroncoming traffic.

• Honda SMART Key System(P.45)

• Idling Stop System(P.55)

• Answer Back System(P.53)


Operation Guide

19

# Braking (P.63) Close the throttle and apply thefront and rear brakes together.u The brakelight will indicate

that you have applied thebrakes.

# Parking (P.12)

# StoppingIf pulling off the road, signal earlyenough to show traffic that you arepulling over, and pull over smoothly.

# Turning CornersDo your brakingbefore enteringcorners.

Gradually reapply throttlewhen exiting turn.

# Refuelling (P.64)

Park on a firm level surface.Use the stand, lock thesteering.

Parts Location


Operation Guide

20

Throttle grip (P.108)Front brake fluid reservoir (P.105)

Tool kit (P.72)

Front brake lever

Engine oil fill cap/dipstick(P.98)

Centre compartment (P.71)

Coolant reserve tank (P.102)

Helmet holder (P.70)

Shopping hook (P.73)

Rear suspension springpreload adjuster (P.111)

Rear carrier (P.73)

Seat (P.69)USB socket (P.67)

Fuel fill cap (P.64)


Operation Guide

21

Side stand (P.107)

Crankcase breather (P.109)

Rear brake lever

Helmet holder (P.70)

Centre stand (P.13)

Spark plug (P.96)

Oil plug/strainer screen(P.100)

Rear brake fluid reservoir(P.105)

Rear suspension springpreload adjuster (P.111)

Battery (P.91)Fuse box (P.136)

EM mode connector (P.129)

Engine oil drain bolt (P.100)

Document bag (P.72)

Data link connector

Instruments


Operation Guide

22

Display CheckWhen the ignition switch is turned to the (On) position, initial animation will show.If any part of these displays does not come on when it should, have your dealercheck for problems.

INFO A button

INFO B button


Operation Guide

23Continued

Fuel gauge(P.28)

Clock (12-hour or 24-hour display)To set the clock: (P.33)

OIL CHANGE indicator(P.30)

Battery voltagemeter (P.28)

Maintenance indicator(P.31)

Speedometer

Switching the Display: (P.24)

Switching the Display:(P.24)

Odometer [TOTAL](P.25) /Available drivingdistance [RANGE] (P.26) /Current fuel mileage[CONS.] (P.25)

Tripmeter [TRIP A/B] (P.26) /Average fuel mileage [AVG](P.27) /Torque Control modedisplay (P.28) /


Operation Guide

24

Instruments (Continued)

The INFO A button switches between the odometer, available driving distance and currentfuel mileage.

The INFO B button switches between the tripmeter A, tripmeter B, and Torque Controlmode display. Also INFO B button switches between the average fuel mileage.

Switching the Display

Press the INFO A button

Press the INFO B button

TripmeterA

Torque Controlmode

TripmeterB

OdometerAvailabledriving distance Current fuel mileage

Average fuelmileage

Average fuelmileage

# OdometerTotal distance ridden.When “------” is displayed, go to your dealerfor service.

# Current fuel mileageDisplays the current or instant fuel mileage.

● When your speed is less than about 7km/h (4 mph): “--.-” is displayed.

● When selecting the “L/100km”,“km/L” or“mile/L”.Display range: 0.0 to 99.9 km/L (L/100kmor mile/L).If the calculated value is 99.9 km/L (L/100km or mile/L) or more: “99.9 km/L (L/100km or mile/L)” is displayed.If the calculated value is less than 0.1 km/L(L/100km or mile/L): “0.0 km/L (L/100kmor mile/L)” is displayed.

● When selecting the “mile/gal”.Display range: 0.0 to 199.9 mile/gal.If the calculated value is 199.9 mile/gal ormore: “199.9 mile/gal” is displayed.If the calculated value is less than 0.1 mile/gal: “0.0 mile/gal” is displayed.

When “--.-” is displayed except for the abovementioned cases, go to your dealer forservice.


Operation Guide

25Continued

# Available driving distanceDisplays the estimated distance you cantravel on the remaining fuel.

Display range: 999 to 0 km (mile)● If the calculated value is 999 km (mile) or

more: “999 km (mile)” is displayed.● Initial display: “---” is displayed.● When the amount of remaining fuel is

below 1.0 L (0.26 US gal, 0.22 Imp gal):“---” is displayed.

The indicated available driving distance iscalculated based on the driving conditions,and the indicated figure may not always bethe actual available distance.

When “---” is displayed except for the abovementioned cases, go to your dealer forservice.

# Tripmeter A/BDistance ridden since tripmeter A ortripmeter B respectively were reset.When “----.-” is displayed, go to your dealerfor service.To reset the tripmeter: (P.29)


Operation Guide

26


# Average fuel mileageDisplays the average fuel mileage since theselected tripmeter was reset.The average fuel mileage will be calculatedbased on value displayed on the tripmeter (Aor B) selected.

● When the tripmeter A or B is reset: “--.-”is displayed.

● When selecting the “L/100km”,“km/L” or“mile/L”.Display range: 0.0 to 99.9 km/L (L/100kmor mile/L).If the calculated value is 99.9 km/L (L/100km or mile/L) or more: “99.9 km/L (L/100km or mile/L)” is displayed.If the calculated value is less than 0.1km/L: “0.0 km/L” is displayed.

● When selecting the “mile/gal”.Display range: 0.0 to 199.9 mile/gal.If the calculated value is 199.9 mile/gal ormore: “199.9 mile/gal” is displayed.If the calculated value is less than 0.1 mile/gal: “0.0 mile/gal” is displayed.

When “--.-” is displayed except for the abovementioned cases, go to your dealer forservice.To reset the average fuel mileage:(P.29)


Operation Guide

27Continued

# Torque Control modeDisplays the current Torque Control setting.Honda selectable torque control(P.58)

# Battery voltage meterDisplays the current voltage.

# Fuel gaugeRemaining fuel when there is only 1st (E)segment: approximately 1.6 L (0.42 US gal,0.35 Imp gal).This segment flashes when the fuel decreasesfurther.

NOTICEYou should refuel when the reading approachesthe E (1st) segment. Running out of fuel cancause the engine to misfire, damaging thecatalytic converter.

If the fuel gauge indicator flashes in arepeat pattern or turns off: (P.121)


Operation Guide

28


# To reset the tripmeter and averagefuel mileage

To reset tripmeter A and average fuelmileage (this is based on tripmeter A)together, press and hold the INFO B buttonwhile tripmeter A is displayed.

To reset tripmeter B and average fuelmileage (this is based on tripmeter B)together, press and hold the INFO B buttonwhile tripmeter B is displayed.


Operation Guide

29Continued

Tripmeter A Tripmeter Aaverage fuelmileage

Tripmeter B Tripmeter Baverage fuelmileage

# OIL CHANGE indicatorThe indicator is turned on whenever therunning distance reaches the programed oilchange interval.When the OIL CHANGE indicator isappeared, reset the indicator after changingthe engine oil. (P.99)u The OIL CHANGE indicator is appeared for

the first time when the running distancereaches 1,000 km (600 miles).

u The OIL CHANGE indicator is appearedwhen the running distance reaches every6,000 km (4,000 miles) after the firstindication was reset.

u The indicator does not go off until it is reset.

If the oil is changed before the oil changeindicator comes on, be sure to reset the OILCHANGE indicator after changing the oil.

To reset the OIL CHANGE indicator(P.33)

You can also check the remaining distance tonext interval of the oil change.

To check the remaining distance(P.32)


Operation Guide

30


OIL CHANGEindicator

# Maintenance indicatorThe indicator is turned on whenever therunning distance reaches the programedmaintenance interval.When the maintenance indicator is appeared,reset the indicator after performing theperiodic maintenance. (P.75)u The maintenance indicator is appeared for

the first time when the running distancereaches 1,000 km (600 miles).

u The maintenance indicator is appearedwhen the running distance reaches every6,000 km (4,000 miles) after first indicationwas reset.

u The indicator does not go off until it is reset.

If the periodic maintenance is performedbefore the maintenance indicator comes on,be sure to reset the maintenance indicatorafter performing the periodic maintenance.

To reset the maintenance indicator(P.33)

You can also check the remaining distance tonext interval of the maintenance.

To check the remaining distance(P.32)


Operation Guide

31Continued

Maintenanceindicator

# To check the remaining distanceYou can check the remaining distance to nextinterval of the oil change and maintenance.Press the INFO A button and INFO B button,each remaining distance appears briefly.


Operation Guide

32


Remaining oilchange distance

Remainingmaintenancedistance

Display SettingFollowing items to change or resetsequentially.• Time format setting• Clock setting• Backlight brightness adjustment• Changing of mileage unit• Changing of fuel mileage meter unit• OIL CHANGE indicator reset mode• Maintenance indicator reset mode


Operation Guide

33Continued

Clock setting

Time format setting

Ordinary display

Press and hold INFO A button and INFO BbuttonPress the INFO B button

Backlight brightness adjustment

OIL CHANGE indicator reset mode

Maintenance indicator reset mode

Changing of fuel mileage meter unit

Changing of mileage unit

If the ignition switch is turned to the (Off)position or the button is not pressed forabout 30 seconds, the control isautomatically switched from the settingmode to the ordinary display.If the button is not pressed for about 30seconds items in the process of being set willbe discarded and only items where settingshave been finalized will be applied.Only if the ignition switch is turned to the

(Off) position will items in the process ofbeing set and those that are finalized beapplied.

1 Time format setting:You can switch the time format between 12hour format or 24 hour format.a Turn the ignition switch to the (On)

position.b Press and hold INFO A button and INFO B

button, the current time format startflashing.

c Press the INFO A button to select “12 hr” or“24 hr”.

d Press the INFO B button. The time format isset, and then the display moves to the clocksetting.


Operation Guide

34


2 Clock setting:a Press the INFO A button until the desired

hour is displayed.u Press and hold the INFO A button to

advance the hour fast.

b Press the INFO B button. The minute digitsstart flashing.

c Press the INFO A button until the desiredminute is displayed.u Press and hold the INFO A button to

advance the minute fast.

d Press the INFO B button. The clock is set,and then the display moves to the backlightbrightness adjustment.


Operation Guide

35Continued

3 Backlight brightness adjustment:You can adjust the brightness to one of fivelevels.a Press the INFO A button. The brightness is

switched.b Press the INFO B button. The backlight is

set, and then the display moves to thechanging of speed and mileage unit.


Operation Guide

36


Press the INFO A button

4 Changing of speed and mileage unit:a Press the INFO A button to select either

“km/h” and “km” or “mph” and “mile”.

When selecting the “mph” & “mile”.• Fuel mileage meter unit shows

“mile/gal” or “mile/L”.When selecting the “km/h” & “km”.• Fuel mileage meter unit shows “km/L”

or “L/100km”.

b Press the INFO B button. The speed andmileage unit is set, and then the displaymoves to the changing of fuel mileagemeter unit.

5 Changing of fuel mileage meter unit:a Press the INFO A button to select either

“L/100km” or “km/L”.


Operation Guide

37Continued

If the “mph” for speed and “mile” formileage are selected, the fuel mileageshown by “mile/gal” or “mile/L”.

b Press the INFO B button. The fuel mileagemeter unit is set, and then the display movesto the OIL CHANGE indicator reset mode.

6 OIL CHANGE indicator reset modePress and hold the INFO A button.The OIL CHANGE indicator and remainingdistance are reset, then the maintenanceindicator and remaining distance startflashing after next interval of the oil change isappeared briefly.u If the OIL CHANGE indicator and remaining

distance are not to be reset, press theINFO B button.


Operation Guide

38


7 Maintenance indicator reset modePress and hold the INFO A button.The maintenance indicator and remainingdistance are reset, then the display will returnto the ordinary display after next interval ofthe maintenance is appeared briefly.u If the maintenance indicator and remaining

distance are not to be reset, press theINFO B button.


Operation Guide

39

Indicators


Operation Guide

40

PGM-FI (Programmed Fuel Injection)malfunction indicator lamp (MIL)

Comes on briefly when the ignition switch isturned to the (On) position.If it comes on while engine is running:(P.117)

If one of these indicators does not come on when it should, have your dealer check forproblems.

Idling Stop indicatorComes on briefly when the Idling Stop switchin the IDLING STOP with the ignition switchturned to the (On) position.Idling Stop system: (P.55)

● Goes off when the ignition switch is turnedto the (On) position.

When the Honda SMART Key IndicatorFlashes: (P.120)

● Comes on when vehicle and HondaSMART Key verification is complete, andthe ignition switch can be operated.

Honda SMART Key indicator

High coolant temperature indicatorComes on when the coolant temperatureexceeds the specified value.If it comes on while riding: (P.116)


Operation Guide

41

Right turn signalindicator

Left turn signalindicator

If it comes on while riding: (P.118)

● Comes on when the ignition switch is turnedto the (On) position.

ABS (Anti-lock Brake System) indicator

High beam indicator

Comes on when the Torque Control isturned to off.

Torque Control OFF indicator

If it comes on while riding: (P.119)

● Blinks when Torque Control isoperating.

● Comes on when the ignition switch isturned to the (On) position.

Torque Control indicator

● Goes off when your speed reachesapproximately 10 km/h (6 mph).

● Goes off when your speed reachesapproximately 3 km/h (2 mph) toindicate Torque Control is ready towork.

Switches


Operation Guide

42

Idling Stop switch

Headlight dimmer/Passing light control switch• : High beam• : Low beam

Start button

Turn signal switchu Pressing the switch turns the turn

signal off. Horn button

• IDLING STOP : The IdlingStop system is on.

• IDLING : The Idling Stopsystem is off.

Idling Stop system: (P.55)

• : Flashes the high beam headlight.

INFO A button

INFO B button


Operation Guide

43Continued

Ignition switchSwitches the electrical system on/off,locks the steering and operates thefuel lid and seat opener switch.To unlock the ignition switch:(P.50)

(On)Turns electrical system on

for starting/riding.

(Lock)Locks steering.

(Off)Turns engine off.

Operates the fuel lid andseat opener switch.

SEAT FUEL

Steering LockLock the steering when parking to helpprevent theft.A U-shaped wheel lock or similar device isalso recommended.

# Lockinga Turn the handlebar all the way to the left.b Push the ignition switch down, and turn it to

the (Lock) position.u To unlock the ignition switch (P.50)u Jiggle the handlebar if the lock is difficult

to engage.c Lock the ignition switch. (P.51)

# UnlockingPush the ignition switch in, and turn it to the

(Off) position.u To unlock the ignition switch (P.50)


Operation Guide

44

Switches (Continued)

Ignition switch

Push Turn

Honda SMART Key SystemThe Honda SMART Key system allows you tooperate the main switch without inserting akey into a keyhole.The system runs a two-way authenticationbetween the vehicle and the Honda SMARTKey to verify if it is the registered HondaSMART Key.

The Honda SMART Key system uses low-intensity radio waves. It may affect medicalequipment such as a cardiac pacemakers.


Operation Guide

45Continued

Switching the Honda SMART KeySystem

# To switch the Honda SMART Keysystem to activation or deactivation

Press the ON/OFF button until the LEDcolour of the Honda SMART Key changes.

# To check the Honda SMART Keysystem status

Lightly press the ON/OFF button. The LED ofthe Honda SMART Key will show the status.When the LED of the Honda SMART Key is:

Green:(activation)

Honda SMART Key systemauthentication can beperformed.

Red:(deactivation)

Honda SMART Key systemauthentication can not beperformed.


Operation Guide

46

Honda SMART Key System (Continued)LED

ON/OFF button

Operating RangeThe operating range varies when the ignitionswitch is locked or unlocked.

The Honda SMART Key system uses low-intensity radio waves. Therefore theoperating range may become wider ornarrower, or the Honda SMART Key systemmay not work properly in the followingenvironments.• When the Honda SMART Key battery is

depleted.• When there are facilities nearby that

generate strong radio waves or noisesuch as TV towers, power stations, radiostations, or airports.

• When you carry the Honda SMART Keywith a laptop or wireless communicationdevice such as a radio or mobile phone.

• When the Honda SMART Key comes intocontact with or is covered by metalobjects.

# When the ignition switch is unlocked:The system can be operated within theshaded area shown in the illustration.


Operation Guide

47Continued

# When the ignition switch is locked:The system can be operated within theshaded area shown in the illustration.

Anyone can unlock the ignition switch andstart the engine if your Honda SMART Key iswithin operating range of your vehicle, evenif you are on the other side of a wall orwindow. If you are away from your vehiclebut your Honda SMART Key is still withinoperating range, deactivate the HondaSMART Key system.To switching the Honda SMART Keysystem (P.46)


Operation Guide

48

Honda SMART Key System (Continued)

About 2 m (6.6 ft)

Anyone in possession of the Honda SMARTKey can perform the following operations ifthe Honda SMART Key is within operatingrange:• Starting the engine• Unlocking the ignition switch• Releasing the seat lock• Opening the fuel lid• Unlocking the steering lock

You should always keep the Honda SMARTKey on your person after you get on and offthe vehicle or while riding.

Do not place the Honda SMART Key in thecentre compartment.

If the ignition switch is in the (On) position,the vehicle can be operated even by aperson who does not have a verified HondaSMART Key.Whenever you leave your vehicle, lock thesteering and lock the ignition switch.(P.51)Make sure the ignition switch ring goes offand all turn signals flash once at this time.


Operation Guide

49Continued

Switching the ignition switch

# To Unlock the Ignition Switcha Make sure that the Honda SMART Key

system is activated. (P.46)b To authenticate the Honda SMART Key

system, push the ignition switch.u When properly authenticated, the

ignition switch is unlocked, and theHonda SMART Key indicator and ignitionswitch ring come on.

c Turn the ignition switch to the (On) positionwhile the Honda SMART Key indicatorcomes on.u If you do not turn the ignition switch to

the (On) position within 20 secondsafter pushing in the ignition switch in, theHonda SMART Key indicator and ignitionswitch ring will go off, the turn signalsflash 1 time, and then the ignition switchwill be locked.

When the Honda SMART Key systemdoes not work properly (P.125)

If someone without the Honda SMART Keytries to turn the ignition switch, the ignitionswitch rotates freely. If you notice the ignitionswitch is in a different position, turn theignition switch to the original position( (Off) or (Lock)).


Operation Guide

50


HondaSMART Key

Honda SMARTKey indicator

Ignitionswitchring

Ignitionswitch

# To Lock the Ignition Switcha Turn the ignition switch to the SEAT FUEL,

(Off) or (Lock) position.b Lock the ignition switch by doing one of the

following:• Leave the operating range with the

Honda SMART Key. (P.47)• Push the ignition switch.• Wait for approximately 20 seconds

after turning the ignition switch from (On) to SEAT FUEL, (Off) or

(Lock) position.• Switch the Honda SMART Key system

to deactivation. (P.46)c Make sure that the Honda SMART Key

indicator and ignition switch ring go off andthe turn signals flash once. This indicatesthat the ignition switch is locked.

When the Honda SMART Key systemdoes not work properly (P.125)


Operation Guide

51Continued

Ignition switchringIgnition

switch

(On)

SEATFUEL

(Lock)

(Off)

Always make sure the ignition switch positionis in the (Off) or (Lock) position whenyou leave your vehicle.

When the ignition switch is locked in theSEAT FUEL position, the ignition switch canbe turned (Off) only once.

When the ignition switch is locked in the (Off) position, the steering cannot be

locked. To lock the steering, unlock theignition switch.


Operation Guide

52


Answer Back SystemThe answer back system is a device to findthe location of your vehicle and to informyou that the immobilizer function of theHonda SMART key system is activated.When you press the answer back button onthe Honda SMART Key with the ignitionswitch (Off) or (Lock) position, the turnsignals blink, and the ignition switch ringlights, informing you of your vehicle'slocation and activation of the immobilizerfunction. The ignition switch ring will light forabout 1 minute.

The answer back system uses low-intensityradio waves. It may affect medical equipmentsuch as a cardiac pacemaker.


Operation Guide

53Continued

Ignitionswitch ring

Answer backbutton

# OperationPress the answer back button on the HondaSMART Key.u The answer back system will not function when

the ignition switch is in the (On) position.

If the ignition switch is left the (Off) or (Lock) position for more than 10 days, the

answer back system will no longer operate.During the system is activating, when thevehicle receives a signal by pressing theanswer back button, the system activation willbe extended for 10 days.To reset the system, unlock the ignitionswitch and turn the ignition switch to the (On) position once.u To unlock the ignition switch. (P.50)NOTICEWhen the battery in the vehicle is weak, theanswer back system may not function.


Operation Guide

54

Answer Back System (Continued)

Idling Stop SystemIdling Stop system is designed to help reducethe fuel consumption and noise, by idlingstop while making a stop such as waiting atan intersection.

# Switching the Idling Stop System Onor Off

Switches the Idling Stop system on or offusing the Idling Stop switch.• ON: IDLING STOPu Idling Stop indicator comes on when the

Idling Stop system becomes ready tostop the engine while riding. Idling Stopindicator flashes when the engine isstopped by the Idling Stop system.

• OFF: IDLINGu Idling Stop indicator does not come on

when the Idling Stop system is off.

Activation of the Idling Stop SystemThe Idling Stop system becomes ready tostop the engine and Idling Stop indicatorcomes on when the following requirementsare satisfied with the Idling Stop switch in theIDLING STOP position:• start the engine by pressing the start

button• warm up the engine enough• ride the vehicle at speeds over 10 km/h (6

mph)

# Idling Stop Indicator Does Not ComeOn: (P.122)


Operation Guide

55Continued

Idling Stop switch Idling Stopindicator

Stopping the engine by the Idling StopSystemThe engine stops and Idling Stop indicatorchanges to flash after you close the throttlecompletely and stop the vehicle while theIdling Stop indicator is on.u While the engine is stopped by the Idling

Stop system, if you press the Idling Stopswitch to IDLING, the Idling Stop system willbe cancelled. The engine will not restarteven when you open the throttle.

Safety Precaution for the Idling Stop SystemDo not go away from the vehicle while theIdling Stop indicator is flashing. When you goaway from the vehicle, always turn theignition switch to the (Off) position.u The engine may start unexpectedly if the

throttle is opened.

# Engine is Not Stopped by the IdlingStop System While the Idling StopIndicator is On: (P.123)NOTICEStopping by the Idling Stop system for a longtime may cause battery discharge.


Operation Guide

56

Idling Stop System (Continued)

Idling Stop indicator

Restarting the EngineCheck that the Idling Stop indicator isflashing, and then open the throttle.u If it is not flashing, you can't restart the

engine with the Idling Stop system, even ifyou open the throttle.

u While the engine is stopped by the IdlingStop system, if you operate the side stand,the flashing Idling Stop indicator turns off orstops flashing and stays on, then the enginewill not restart even when you open thethrottle.

# Engine Does Not Start Even If theThrottle is Opened: (P.124)

NOTICEHeadlight stays on after the engine is stopped bythe Idling Stop system. The battery maydischarge and you may not be able to restartengine.When the battery is weak, switch the Idling Stopswitch to IDLING and do not to use the IdlingStop system. See your dealer to check thebattery.

See your dealer for checking the battery asspecified in the maintenance schedule.

# Maintenance Schedule: (P.76)


Operation Guide

57

Honda selectable torque controlTorque Control (engine power control) canbe turned on/off.u Do not operate the Torque Control switch

while riding.Stop the vehicle first, turn the TorqueControl off or on.

u The Torque Control cannot be turned offwhen the system is activated (TorqueControl indicator blinking).

u Each time the ignition switch is turned to the (On) position, the Torque Control willautomatically be set to on .

Torque Control on and off1. Select the Torque Control mode.(P.24)

2. Torque Control can be turned on and off bypressing and holding the INFO B button.u If the Torque Control is enabled (On),

“HSTC ON” is displayed and the TorqueControl OFF indicator goes off.

u If the Torque Control is disabled (Off),“HSTC OFF” is displayed and the TorqueControl OFF indicator comes on.


Operation Guide

58

INFO B button

Torque ControlOFF indicator

Starting the EngineStart your engine using the followingprocedure, regardless of whether the engine iscold or warm.

This vehicle is equipped with a side standignition cut-off system.u If the side stand is down, the engine cannot

be started.u If you lower the side stand with the engine

running, it will automatically shut off.This vehicle is equipped with a HondaSMART Key system. Always keep HondaSMART Key on you when you ride thevehicle. (P.47)

If the engine of this vehicle is stopped whilethe ignition switch is in the (On) position,authentication will be disabled after a certainamount of time or if you leave theauthentication range. Restart the engine byperforming step c & d under the startingprocedure.

u If the engine of this vehicle is stopped by theIdling Stop System, authentication will notbe disabled.

NOTICE• If the engine does not start within 5 seconds,

turn the ignition switch to the (Off)position and wait 10 seconds before trying tostart the engine again to recover batteryvoltage.

• Extended fast idling and revving the enginecan damage the engine, and the exhaustsystem.

• The engine will not start if the throttle is fullyopen.

• If the vehicle is over-turned, you must firstturn the ignition switch to the (Off)position and then inspect the vehiclecarefully.


Operation Guide

59Continued

a Place the vehicle on its centre stand.b Turn the ignition switch to the (On)

position.u To unlock the ignition switch. (P.50)

c Squeeze the rear brake lever.u The starter motor will only work when

the rear brake lever is squeezed and theside stand is up.

d Press the start button with the throttlecompletely closed. Release the start buttonas soon as the engine starts.


Operation Guide

60

Starting the Engine (Continued)

If you cannot start the engine:aPlace the vehicle on its centre stand and

squeeze the rear brake lever.bWith the throttle slightly open (about 3 mm,

without freeplay), press the start button.

If the engine does not start:aOpen the throttle fully and press the start

button for 5 seconds.bRepeat the normal starting procedure.c If the engine starts, open the throttle slightly

if idling is unstable.d If the engine does not start, wait 10 seconds

before trying steps a & b again.

# If Engine Will Not Start (P.115)


Operation Guide

61

About 3 mm, without freeplay

RidingStarting the Vehiclea Push the vehicle forward off the centre

stand.u Squeeze the rear brake lever.u Keep throttle closed.

Make sure the side stand and centre standare up.b Get on the vehicle.

u Mount the vehicle from the left side,keeping at least one foot on the ground.

c Release the brake lever.

d Acceleration and decelerationTo accelerate: Open the throttle slowly.To decelerate: Close the throttle.


Operation Guide

62

Close (Decelerate) Open (Accelerate)

BrakingClose the throttle and apply the front andrear brake levers together.


Operation Guide

63

Rear brake lever Front brake lever

RefuellingFuel type: Unleaded petrol onlyFuel octane number: Your vehicle isdesigned to use Research Octane Number(RON) 95 or higher.Tank capacity: 7.0 L (1.85 US gal, 1.54 Impgal)

# Refuelling and Fuel Guidelines (P.14)

Opening the Fuel Fill Capa Turn the ignition switch to the SEAT FUEL

position.u To unlock the ignition switch (P.50)

b Push the FUEL side of the fuel lid and seatopener switch.u The fuel lid opens.


Operation Guide

64

SEATFUEL

Fuel lid

Fuel lid andseat opener

switch

FUELIgnitionswitch

c Turn the fuel fill cap counterclockwise andremove the fuel fill cap.

How to RefuelTo refuel with automatic stop fillernozzle:a Insert the filler nozzle fully.

u It can be put in easily by swinging nozzleback and forth.


Operation Guide

65Continued

Arrow marks

Fuel fill cap Groove Filler nozzle

Groove

bRefuel until it stops automatically.u When the tank is full, the fuel nozzle will

click off automatically.u If the nozzle is not fully inserted, the

automatic stop does not function, whichmay cause fuel to overflow from the fuelfiller opening.

To refuel without automatic stop fillernozzle:Refuel to the groove. Add fuel slowly so it doesnot overflow from the fuel filler opening.

3WARNINGPetrol is highly flammable and explosive.You can be burned or seriously injuredwhen handling fuel.

• Stop the engine, and keep heat,sparks, and flame away.

• Handle fuel only outdoors.• Wipe up spills immediately.

3CAUTIONDo not add fuel after the filler nozzleautomatically stops.

The filler nozzle automatically stops to leavespace in the fuel tank so that fuel does notoverflow as a result of changes in airtemperature.

Closing the Fuel Fill Capa Install and tighten the fuel fill cap firmly by

turning it clockwise.u Make sure that the arrow marks on the

cap and fuel tank are aligned.bClose the fuel lid until it locks.

u Make sure that the fuel lid is closedsecurely.


Operation Guide

66

Refuelling (Continued)

USB SocketThe USB socket is located in the centrecompartment.Use USB devices at your own risk. In no eventshall Honda be liable for any damage to yourUSB device when in use.

Only USB devices within the followingspecifications can be connected.Open the cover to access the USB socket.Rated capacity is7.5 W (5 V, 1.5 A).Do not connect USB devices that exceed therated capacity. They may not be charged orwork properly even if connected.For information on usage or malfunction ofthe USB device you connect, refer to itsinstruction manual.

To connect your USB devicea Open the seat. (P.69)b Open the cover to access the USB socket.

c Connect a certified USB cable to the USBsocket.


Operation Guide

67Continued

Cover

USB socket

u To prevent the battery from becoming weak(or dead), keep the engine running whiledrawing current from the USB socket.

u To prevent entry of foreign matter into theUSB socket, be sure to close the cover whenthe USB socket is not used.

u Carefully secure all connected devices, asvibration may cause damage to them orthey could shift unexpectedly.

NOTICE• Using any heat-generating USB devices or

improperly rated USB devices can damagethe USB socket.

• Do not use the USB socket in wet conditions,when or while washing or any other wetconditions as these will damage the USBsocket.

• Do not allow the USB's harness to becomepinched or trapped.


Operation Guide

68

USB Socket (Continued)

Storage EquipmentSeat Opena Turn the handlebar pointed straight ahead.b Turn the ignition switch to the position of

SEAT FUEL.u To unlock the ignition switch. (P.50)

c Push the SEAT side of the fuel lid and seatopener switch.

d Open the seat.

Seat CloseClose and push down on the rear of the seatuntil locks. Make sure that the seat is lockedsecurely to pull it up lightly.Take care not to lock your keys in thecompartment under the seat.


Operation Guide

69Continued

Seat Ignition switch

SEAT FUEL

Fuel lid and seatopener switch

SEAT

Helmet HoldersThe helmet holders are located under theseat.u Use the helmet holders only when parked.

# Opening the Seat (P.69)

3WARNINGRiding with a helmet attached to theholder can interfere with your ability tosafely operate the vehicle and couldlead to a crash in which you can beseriously hurt or killed.

Use the helmet holder only whileparked. Do not ride with a helmetsecured by the holder.


Operation Guide

70

Storage Equipment (Continued)

Helmet holders

A helmet can be stored in the centrecompartment.Set in the front of the helmet forward.u Some helmets may not fit in the

compartment due to their size or design.

Centre compartmentNever exceed the maximum weight limit.Maximum Weight: 10 kg (22 lb)u Do not store any items that are flammable

of susceptible to heat damage.u Do not store valuables or fragile articles.



Operation Guide

71Continued

Centre compartment

Helmet

Document BagThe document bag is in the centrecompartment. The owner’s manual should bestored the document bag and placed in thecentre compartment.


Tool KitThe tool kit is in the reverse side of the seatby the rubber strap.



Operation Guide

72

Storage Equipment (Continued)

Document bagOwner's manual

Centre compartment

Tool kit

Rubber strap

Shopping HookThe shopping hook is provided below thehandlebar.u Do not attach large luggage to the hook

that would hang out from the vehicle and/orinterfere with the movement of your feet.

The maximum allowable load on theshopping hook shall be no more than1.5 kg (3.3 lb).

Rear CarrierNever exceed the maximum weight limit.Maximum Weight: 3 kg (6.6 lb)

II ED, III ED type onlyLid switch is used for optional parts.


Operation Guide

73

Shopping hook

Rear carrier Lid switchII ED, III ED type only

Importance of Maintenance ...........................P. 75Maintenance Schedule.....................................P. 76Maintenance Fundamentals ...........................P. 79Tool .......................................................................P. 90Removing & Installing Body Components..P. 91

Battery .................................................................... P. 91Battery Cover........................................................ P. 93Clip .......................................................................... P. 94Maintenance Lid .................................................. P. 95

Spark Plug ...........................................................P. 96Engine Oil ............................................................P. 98Coolant ..............................................................P. 102Brakes.................................................................P. 105Side Stand .........................................................P. 107

Throttle ..............................................................P. 108Crankcase Breather .........................................P. 109Other Adjustments..........................................P. 110

Adjusting the Headlight Aim.......................... P. 110Adjusting the Rear Suspension...................... P. 111

Other Replacement.........................................P. 112Replacing the Honda SMART Key Battery .. P. 112


Please read “Importance of Maintenance” and “Maintenance Fundamentals” carefullybefore attempting any maintenance. Refer to “Specifications” for service data.

Maintenance

Importance of Maintenance

Importance of MaintenanceKeeping your vehicle well-maintained isabsolutely essential to your safety and toprotect your investment, obtain maximumperformance, avoid breakdowns, and reduce airpollution. Maintenance is the owner'sresponsibility. Be sure to inspect your vehiclebefore each ride, and perform the periodicchecks specified in the Maintenance Schedule.2 P. 76

3WARNINGImproperly maintaining your vehicle orfailing to correct a problem before youride can cause a crash in which you canbe seriously hurt or killed.

Always follow the inspection andmaintenance recommendations andschedules in this owner's manual.

Maintenance SafetyAlways read the maintenance instructionsbefore you begin each task, and make sure thatyou have the tools, parts, and skills required.We cannot warn you of every conceivablehazard that can arise in performingmaintenance. Only you can decide whether ornot you should perform a given task.

Follow these guidelines when performingmaintenance.● Stop the engine and turn the ignition switch

to the (Off) position.● Place your vehicle on a firm, level surface

using the side stand, centre stand or amaintenance stand to provide support.

● Allow the engine, muffler, brakes, and otherhigh-temperature parts to cool beforeservicing as you can get burned.

● Run the engine only when instructed, anddo so in a well-ventilated area.


Maintenance

75

Maintenance ScheduleThe maintenance schedule specifies themaintenance requirements necessary to ensuresafe, dependable performance, and properemission control.

Maintenance work should be performed inaccordance with Honda's standards andspecifications by properly trained and equippedtechnicians. Your dealer meets all of theserequirements. Keep an accurate record ofmaintenance to help ensure that your vehicle isproperly maintained.Make sure that whomever performs themaintenance completes this record.

All scheduled maintenance is considered anormal owner operating cost and will becharged to you by your dealer. Retain allreceipts. If you sell the vehicle, these receiptsshould be transferred with the vehicle to thenew owner.

Honda recommends that your dealer shouldroad test your vehicle after each periodicmaintenance is carried out.


Maintenance

76

ItemsPre-rideCheck2 P. 79

Frequency *1AnnualCheck

RegularReplace

Refer topage× 1,000 km 1 6 12 18 24 30 36

× 1,000 mi 0.6 4 8 12 16 20 24Fuel Line –Fuel Level –Throttle Operation 108Air Cleaner *2 89Crankcase Breather *3 109Spark Plug 96Valve Clearance –Engine Oil 99Engine Oil Strainer Screen 99Engine Idle Speed –Radiator Coolant *4 3 Years 102Cooling System –Evaporative EmissionControl System –

Maintenance Level Maintenance Legend: Intermediate. We recommend service by yourdealer, unless you have the necessary tools and aremechanically skilled.Procedures are provided in an official Honda Shop Manual.

:::

Inspect (clean, adjust, lubricate, or replace, if necessary)ReplaceClean

: Technical. In the interest of safety, have your vehicleserviced by your dealer.


Maintenance ScheduleM

aintenance

77Continued

ItemsPre-rideCheck2 P. 79

Frequency *1AnnualCheck

RegularReplace

Refer topage× 1,000 km 1 6 12 18 24 30 36

× 1,000 mi 0.6 4 8 12 16 20 24Drive Belt –Final Drive Oil *4 2 Years –Battery 82Brake Fluid *4 2 Years 105Brake Pads Wear 106Brake System 79Headlight Aim 110Lights/Horn –Clutch Shoes Wear –Side Stand 107Suspension –Nuts, Bolts, Fasteners –Wheels/Tyres 86Steering Head Bearings –

Notes:*1 : At higher odometer reading, repeat at the frequency interval established here.*2 : Service more frequently when riding in unusually wet or dusty areas.*3 : Service more frequently when riding in rain or at full throttle.*4 : Replacement requires mechanical skill.


Maintenance Schedule

Maintenance

78

Maintenance Fundamentals

Pre-ride InspectionTo ensure safety, it is your responsibility toperform a pre-ride inspection and make surethat any problem you find is corrected. A pre-ride inspection is a must, not only for safety, butbecause having a breakdown, or even a flattyre, can be a major inconvenience.

Check the following items before you get onyour vehicle:● Fuel level - Fill fuel tank when necessary.

2 P. 64● Throttle - Check for smooth opening and

full closing in all steering positions. 2 P. 108● Engine oil level - Add engine oil if necessary.

Check for leaks. 2 P. 98● Coolant level - Add coolant if required.

Check for leaks. 2 P. 102

● Brakes - Check operation;Front and Rear: check brake fluid level andpads wear. 2 P. 105, 2 P. 106

● Lights and horn - Check that lights,indicators and horn function properly.

● Side stand ignition cut-off system - Checkfor proper function. 2 P. 107

● Wheels and tyres - Check condition, airpressure and adjust if necessary. 2 P. 86


Maintenance

79

Replacing PartsAlways use Honda Genuine Parts or theirequivalents to ensure reliability and safety.When ordering coloured components, specifythe model name, colour, and code mentionedon the colour label.The colour label is attached to the centrecompartment under the seat. 2 P. 69

3WARNINGInstalling non-Honda parts may makeyour vehicle unsafe and cause a crash inwhich you can be seriously hurt orkilled.

Always use Honda Genuine Parts orequivalents that have been designedand approved for your vehicle.



Maintenance

80

Colour label

BatteryYour vehicle has a maintenance-free typebattery. You do not have to check the batteryelectrolyte level or add distilled water. Clean thebattery terminals if they become dirty orcorroded.Do not remove the battery cap seals. There isno need to remove the cap when charging.

NOTICEYour battery is a maintenance-free type and canbe permanently damaged if the cap strip isremoved.

This symbol on the battery meansthat this product must not be treatedas household waste.

NOTICEAn improperly disposed of battery can beharmful to the environment and human health.Always confirm local regulations for properbattery disposal instruction.


Maintenance FundamentalsM

aintenance

81Continued

# What to do in an emergencyIf any of the following occur, immediately seeyour doctor.● Electrolyte splashes into your eyes:

u Wash your eyes repeatedly with coolwater for at least 15 minutes. Using waterunder pressure can damage your eyes.

● Electrolyte splashes onto your skin:u Remove affected clothing and wash your

skin thoroughly using water.● Electrolyte splashes into your mouth:

u Rinse mouth thoroughly with water, anddo not swallow.

3WARNINGThe battery gives off explosivehydrogen gas during normal operation.

A spark or flame can cause the batteryto explode with enough force to kill orseriously hurt you.

Wear protective clothing and a faceshield, or have a skilled mechanic dothe battery servicing.

# Cleaning the Battery Terminals1. Remove the battery. 2 P. 912. If the terminals are starting to corrode and

are coated with a white substance, washwith warm water and wipe clean.



Maintenance

82

3. If the terminals are heavily corroded, cleanand polish the terminals with a wire brush orsandpaper. Wear safety glasses.

4. After cleaning, reinstall the battery.

The battery has a limited life span. Consult yourdealer about when you should replace thebattery. Always replace the battery with anothermaintenance-free battery of the same type.

NOTICEInstalling non-Honda electrical accessories canoverload the electrical system, discharging thebattery and possibly damaging the system.

FusesFuses protect the electrical circuits on yourvehicle. If something electrical on your vehiclestops working, check for and replace any blownfuses. 2 P. 136

# Inspecting and Replacing FusesTurn the ignition switch to the (Off) positionto remove and inspect fuses. If a fuse is blown,replace with a fuse of the same rating. For fuseratings, see “Specifications.” 2 P. 154

NOTICEReplacing a fuse with one that has a higherrating greatly increases the chance of damage tothe electrical system.



aintenance

83Continued

Blown fuse

MB

If a fuse fails repeatedly, you likely have anelectrical fault. Have your vehicle inspected byyour dealer.

Engine OilEngine oil consumption varies and oil qualitydeteriorates according to riding conditions andtime elapsed.Check the engine oil level regularly, and add therecommended engine oil if necessary. Dirty oilor old oil should be changed as soon aspossible.

# Selecting the Engine OilFor recommended engine oil, see“Specifications.” 2 P. 153

If you use non-Honda engine oil, check thelabel to make sure that the oil satisfies all of thefollowing standards:● JASO T 903 standard*1: MB● SAE standard*2: 10W-30● API classification*3: SG or higher

*1. The JASO T 903 standard is an index for engineoils for 4-stroke motorcycle engines. There aretwo classes: MA and MB. For example, thefollowing label shows the MB classification.

*2. The SAE standard grades oils by their viscosity.*3. The API classification specifies the quality and

performance rating of engine oils. Use SG orhigher oils, excluding oils marked as “EnergyConserving” or “Resource Conserving” on thecircular API service symbol.



Maintenance

84

Oil code

Oil classification

Not recommended Recommended

Brake FluidDo not add or replace brake fluid, except in anemergency. Use only fresh brake fluid from asealed container. If you do add fluid, have thebrake system serviced by your dealer as soon aspossible.

NOTICEBrake fluid can damage plastic and paintedsurfaces.Wipe up spills immediately and wash thoroughly.

Recommended brake fluid:Honda DOT 3 or DOT 4 Brake Fluid orequivalent

Recommended CoolantPro Honda HP Coolant is a pre-mixed solutionof antifreeze and distilled water.

Concentration:50% antifreeze and 50% distilled water

A concentration of antifreeze below 40% willnot provide proper corrosion and coldtemperature protection.A concentration of up to 60% will provide betterprotection in colder climates.

NOTICEUsing coolant not specified for aluminiumengines or tap/mineral water can causecorrosion.



aintenance

85

Crankcase BreatherService more frequently when riding in rain, atfull throttle, or after the vehicle is washed oroverturned. Service if the deposit level can beseen in the transparent section of the draintube.If the drain tube overflows, the air filter maybecome contaminated with engine oil causingpoor engine performance. 2 P. 109

Tyres (Inspecting/Replacing)# Checking the Air PressureVisually inspect your tyres and use an airpressure gauge to measure the air pressure atleast once a month or any time you think thetyres look low. Always check air pressure whenyour tyres are cold.

# Inspecting for DamageInspect the tyres forcuts, slits, or cracks thatexposes fabric orcords, or nails or otherforeign objectsembedded in the sideof the tyre or the tread.Also inspect for any unusual bumps or bulges inthe side walls of the tyres.# Inspecting for Abnormal WearInspect the tyres forsigns of abnormal wearon the contact surface.



Maintenance

86

# Inspecting Tread DepthInspect the tread wear indicators. If theybecome visible, replace the tyres immediately.SH150ADFor safe riding, you should replace the tyreswhen the minimum tread depth is reached.

3WARNINGRiding on tyres that are excessivelyworn or improperly inflated can cause acrash in which you can be seriously hurtor killed.

Follow all instructions in this owner'smanual regarding tyre inflation andmaintenance.

Germany (SH150AD only)German law prohibits use of tyres whose treaddepth is less than 1.6 mm.



aintenance

87Continued

Wear indicatorlocation mark

or TWI

Have your tyres replaced by your dealer.SH125ADFor recommended tyres and air pressure,see“Specifications.” 2 P. 153SH150ADFor recommended tyres, air pressure andminimum tread depth, see “Specifications.”2 P. 153Follow these guidelines whenever you replacetyres.● Use the recommended tyres or equivalents

of the same size, construction, speed rating,and load range.

● Front wheel only Have the wheel balancedwith Honda Genuine balance weights orequivalent after the tyre is installed.

● Do not install a tube inside a tubeless tyreon this vehicle. Excessive heat build-up cancause the tube to burst.

● Use only tubeless tyres on this vehicle.The rims are designed for tubeless tyres,and during hard acceleration or braking, atube-type tyre could slip on the rim andcause the tyre to rapidly deflate.

3WARNINGInstalling improper tyres on yourvehicle can adversely affect handlingand stability, and can cause a crash inwhich you can be seriously hurt orkilled.

Always use the size and type of tyresrecommended in this owner's manual.



Maintenance

88

Air CleanerThis vehicle is equipped with a viscous type aircleaner element.Air blow cleaning or any other cleaning candegrade the viscous element performance andcause the intake of dust.Do not perform the maintenance. Should beserviced by your dealer.



aintenance

89

ToolThe tool kit is in reverse side of the seat. 2 P. 69

You can perform some roadside repairs, minoradjustments and parts replacement with theprovided tools.

● Standard/Phillips screwdriver● Screwdriver handle● 10 × 14 mm Open end wrench● Pin spanner● Extension bar● EM mode coupler


Maintenance

90

Removing & Installing Body Components

Battery # RemovalMake sure the ignition switch is in the

(Off) position.1. Remove the battery cover. 2 P. 932. Unhook the rubber band.3. Disconnect the negative - terminal from

the battery.4. Disconnect the positive + terminal from

the battery.5. Remove the battery taking care not to

drop the terminal nuts.


Maintenance

91Continued

Positiveterminal

Battery Negativeterminal

Rubber band

# InstallationInstall the parts in the reverse order ofremoval. Always connect the positive +terminal first. Make sure that bolts and nutsare tight.Make sure the clock information is correctafter the battery is reconnected. 2 P. 33

For proper handling of the battery, see“Maintenance Fundamentals.” 2 P. 81“Battery Goes Dead.” 2 P. 133


Removing & Installing Body Components u Battery

Maintenance

92

Battery Cover # Removal1. Open the seat. 2 P. 692. Remove the battery cover by removing

the clips. 2 P. 94

# InstallationInstall the parts in the reverse order ofremoval.


Removing & Installing Body Components u Battery CoverM

aintenance

93

Battery cover Clips

Clip# Removal

1. Press down on the centre pin to releasethe lock.

2. Pull the clip out of the hole.

# Installation1. Push the bottom of the centre pin.

2. Insert the clip into the hole.3. Press down on the centre pin to lock the

clip.


Removing & Installing Body Components u Clip

Maintenance

94

Centre pin

Maintenance Lid # Removal1. Open the seat. 2 P. 692. Remove the screws.3. Remove the maintenance lid by inserting

a flat head screwdriver covered with aprotective cloth into the slit on the floor.

# InstallationInstall the parts in the reverse order ofremoval.


Removing & Installing Body Components u Maintenance LidM

aintenance

95

Maintenance lid

Screws

Spark Plug

Checking Spark PlugFor the recommended spark plug, see“Specifications.” 2 P. 153

Use only the recommended type of sparkplug in the recommended heat range.

NOTICEUsing a spark plug with an improper heat rangecan cause engine damage.

1. Remove the maintenance lid. 2 P. 952. Disconnect the spark plug cap from the

spark plug.3. Clean any dirt from around the spark plug

base.4. Remove the spark plug using a suitable

spark plug wrench.

5. Inspect the electrodes and centreporcelain for deposits, erosion or carbonfouling.u If the erosion or deposit is heavy,

replace the plug.u Clean a carbon or wet-fouled plug

with a plug cleaner, otherwise use awire brush.


Maintenance

96

Spark plug cap

6. Check the spark plug gap using a wire-type feeler gauge.u If adjustment is necessary, bend the

side electrode carefully.

The gap should be:0.8 - 0.9 mm (0.03 - 0.04 in)

7. Make sure the plug washer is in goodcondition.

8. Install the spark plug. With the plugwasher attached, thread the spark plug inby hand to prevent cross-threading.

9. Tighten the spark plug:● If the old plug is good:

1/8 turn after it seats● If installing a new plug, tighten it twice to

prevent loosening:a) First, tighten the plug:

1/2 turn after it seatsb) Then loosen the plug.c) Next, tighten the plug again:

1/8 turn after it seatsNOTICEAn improperly tightened spark plug can damagethe engine. If a plug is too loose, a piston may bedamaged. If a plug is too tight, the threads maybe damaged.

10. Install the parts in the reverse order ofremoval.u When reinstalling the spark plug cap,

take care to avoid pinching any cablesor wires.


Spark Plug u Checking Spark PlugM

aintenance

97

Spark plug gap

Side electrode

Plug washer

Engine Oil

Checking the Engine OilCheck the engine oil with the Idling Stopswitch at IDLING.

1. If the engine is cold, idle the engine for 3to 5 minutes.

2. Turn the ignition switch to the (Off)position and wait for 2 to 3 minutes.

3. Place your vehicle on its centre stand on afirm, level surface.

4. Remove the oil fill cap/dipstick and wipe itclean.

5. Insert the oil fill cap/dipstick until it seats,but don't screw it in.

6. Check that the oil level is between theupper level and lower level marks on theoil fill cap/dipstick.

7. Securely install the oil fill cap/dipstick.


Maintenance

98

Upper level

Lower levelOil fill cap/dipstick

Adding Engine OilIf the engine oil is below or near the lowerlevel mark, add the recommended engine oil.2 P. 84, 2 P. 1531. Remove the oil fill cap/dipstick. Add the

recommended oil until it reaches theupper level mark.u Place your vehicle on its centre stand

on a firm, level surface when checkingthe oil level.

u Do not overfill above the upper levelmark.

u Make sure no foreign objects enter theoil filler opening.

u Wipe up any spills immediately.2. Securely reinstall the oil fill cap/dipstick.

NOTICEOverfilling with oil or operating with insufficientoil can cause damage to your engine. Do not mixdifferent brands and grades of oil.

For the recommended oil and oil selectionguidelines, see “Maintenance Fundamentals.”2 P. 84

Changing Engine Oil, CleaningStrainer ScreenChanging the oil and cleaning the strainerscreen requires special tools. We recommendthat you have your vehicle serviced by yourdealer.

Change the engine oil with the Idling Stopswitch at IDLING.

1. If the engine is cold, idle the engine for 3to 5 minutes.

2. Turn the ignition switch to the (Off)position and wait for 2 to 3 minutes.


Engine Oil u Adding Engine OilM

aintenance

99Continued


4. Place a drain pan under the drain boltand oil plug.

5. Remove the oil fill cap/dipstick, drain boltand sealing washer to drain the oil.

6. Remove the oil plug, O-ring, spring andoil strainer screen and let the remainingoil drain out.u Discard the oil at an approved

recycling centre.7. Clean the oil strainer screen.8. Check that the oil strainer screen and

sealing rubber are in good condition.9. Replace the O-ring and apply a thin coat

of engine oil to the new O-ring beforeinstalling it.

10. Install the oil strainer screen, spring andoil plug and tighten.

Torque: 20 N·m (2.0 kgf·m, 15 lbf·ft)


Engine Oil u Changing Engine Oil, Cleaning Strainer Screen

Maintenance

100

Sealing washer

Drain bolt

Oil plug

O-ring

Oil strainer screen

Spring

11. Install a new sealing washer onto thedrain bolt. Tighten the drain bolt.

Torque: 24 N·m (2.4 kgf·m, 18 lbf·ft)

12.Fill the crankcase with the recommendedoil (2 P. 84, 2 P. 153) and install the oil fillcap/dipstick.

Required oilWhen changing oil & cleaning thestrainer screen:0.9 L (1.0 US qt, 0.8 Imp qt)When changing oil only:0.8 L (0.8 US qt, 0.7 Imp qt)

13.Check the oil level. 2 P. 9814.Check that there are no oil leaks.After changing the engine oil, reset the oilchange indicator. 2 P. 33


Engine Oil u Changing Engine Oil, Cleaning Strainer ScreenM

aintenance

101

Coolant

Checking the CoolantCheck the coolant level in the reserve tankwhile the engine is cold.1. Place your vehicle on its centre stand on a

firm, level surface.2. Check that the coolant level is between

the UPPER level and LOWER level markson the reserve tank.

If the coolant level is dropping noticeably orthe reserve tank is empty, you likely have aserious leak. Have your vehicle inspected byyour dealer.


Maintenance

102

UPPER level mark

LOWER level markReserve tank

Adding CoolantIf the coolant level is below the LOWER levelmark, add the recommended coolant(2 P. 85) until the level reaches the UPPERlevel mark.Add fluid only from the reserve tank cap anddo not remove the radiator cap.1. Remove the battery cover. 2 P. 932. Remove the reserve tank cap and add

fluid while monitoring the coolant level.u Do not overfill above the UPPER level

mark.u Make sure no foreign objects enter the

reserve tank opening.


Coolant u Adding CoolantM

aintenance

103Continued

Reserve tank cap

3. Securely reinstall the reserve tank cap.4. Install the parts in the reverse order of

removal.

3WARNINGRemoving the radiator cap while theengine is hot can cause the coolant tospray out, potentially scalding you.

Always let the engine and radiator cooldown before removing the radiator cap.

Changing CoolantHave your dealer change the coolant unlessyou have the proper tools and aremechanically qualified.


Coolant u Changing Coolant

Maintenance

104

Brakes

Checking Brake Fluid1. Place your vehicle in an upright position

on a firm, level surface.2. Check that the brake fluid reservoir is

horizontal and that the fluid level is abovethe LOWER level mark.

If the brake fluid level in either reservoir isbelow the LOWER level mark or both thebrake levers freeplay becomes excessive,inspect the brake pads for wear.

If the brake pads are not worn, you mostlikely have a leak. Have your vehicleinspected by your dealer.


Maintenance

105

Front brake

Rear brake

Front brake fluidreservoir

LOWER level mark

LOWER level mark

Rear brake fluidreservoir

Inspecting the Brake PadsCheck the condition of the brake pad wearindicators.The pads need to be replaced if a brake padis worn to the bottom of the indicator.

1. Front Inspect the brake pads from in frontof the brake caliper.

2. Rear Inspect the brake pads from the rearleft of the vehicle.

If necessary have the pads replaced by yourdealer.Always replace both left and right brake padsat the same time.


Brakes u Inspecting the Brake Pads

Maintenance

106

Front

Wear indicators

Rear

Brake pads

Wear indicatorDisc

Brake pads

Disc

Side Stand

Checking the Side Stand


2. Check that the side stand operatessmoothly. If the side stand is stiff orsqueaky, clean the pivot area andlubricate the pivot bolt with clean grease.

3. Sit on the vehicle and raise the side stand.4. Start the engine.

5. Lower the side stand all the way. Theengine should stop as you lower the sidestand. If the engine doesn't stop, haveyour vehicle inspected by your dealer.


Maintenance

107

Side standspring

Throttle

Checking the ThrottleWith the engine off, check that the throttlerotates smoothly from fully closed to fullyopen in all steering positions and throttlefreeplay is correct. If the throttle does notmove smoothly, close automatically, or if thecable is damaged, have the vehicle inspectedby your dealer.

Freeplay at the throttle grip flange:2 - 6 mm (0.1 - 0.2 in)


Maintenance

108

Freeplay

Flange

Crankcase Breather

Cleaning the CrankcaseBreather1. Place a suitable container to receive

deposits.2. Remove the crankcase breather plug from

the air cleaner case and drain depositsinto the container.

3. Reinstall the crankcase breather plug.


Maintenance

109

Crankcasebreather plug

Other Adjustments

Adjusting the Headlight AimYou can adjust vertical aim of the headlightfor proper alignment. Turn the pinion in orout as necessary using a Phillips screwdriverprovided in the tool kit (2 P. 90).Obey local laws and regulations.


Maintenance

110

PinionLower

Raise

Adjusting the Rear Suspension# Spring PreloadYou can adjust the spring preload by theadjuster to suit the load or the road surface.Use the pin spanner and extension bar toturn the adjuster.Position 1 is for a decrease spring preload(soft), or turn the position 3 to 5 increasespring preload (hard). The standard positionis 2.

NOTICEAttempting to adjust directly from 1 to 5 or 5 to 1may damage the shock absorber.

NOTICEDo not turn the adjuster beyond its limits.Adjust both left and right shock absorbers to thesame spring preload.


Other Adjustments u Adjusting the Rear SuspensionM

aintenance

111

1 2 3 4 5

Pin spanner

Extension bar

Other Replacement

Replacing the Honda SMARTKey BatteryIf the Honda SMART Key indicator flashes 5times when the ignition switch is turned tothe (On) position, or the operating rangebecomes unstable, replace the battery assoon as possible.We recommend to see your dealer for thisservice.

Battery type: CR2032

1. Remove the upper case by inserting acoin or a flat head screwdriver coveredwith a protective cloth into the slit.u Wrap a coin or a screwdriver with a

protective cloth to prevent scratchingthe Honda SMART Key.

u Do not touch the circuit or terminal.This may cause problems.

u Be careful to avoid scratching thewaterproof covering or allowing dustto enter.

u Do not forcibly dismantle the HondaSMART Key body.


Maintenance

112

2. Replace the old battery with a newbattery with the negative - side facingup.

3. Snap the two halves of the remotetransmitter back together.u Make sure that upper and lower cases

are set in the right position.

3WARNINGChemical Burn Hazard: do notswallow battery.If swallowed, the battery can causesevere internal burns and even death.• Keep battery away from children and

battery compartment securelyclosed.

• If the battery compartment does notclose securely, stop using theproduct and keep it away fromchildren.

• Immediately seek medical attentionif a child may have swallowedbattery.


Other Replacement u Replacing the Honda SMART Key BatteryM

aintenance

113

Slit

Protectivecloth

Battery

Lower case

Upper case

Engine Will Not Start......................................P. 115Overheating (High coolant temperatureindicator is on) ...............................................P. 116

Warning Indicators On or Flashing.............P. 117PGM-FI (Programmed Fuel Injection)Malfunction Indicator Lamp (MIL)............... P. 117

ABS (Anti-lock Brake System) Indicator ....... P. 118Torque Control Indicator................................. P. 119Honda SMART Key Indicator.......................... P. 120

Other Warning Indications ...........................P. 121Fuel Gauge Failure Indication......................... P. 121

When the Idling Stop System Does NotOperate Properly...........................................P. 122

Idling Stop Indicator Does Not Come On ..P. 122Engine is Not Stopped by the Idling Stop SystemWhile the Idling Stop Indicator is On......... P. 123

Engine Does Not Start Even If the Throttle isOpened ............................................................. P. 124

When the Honda SMART Key System Does NotOperate Properly...........................................P. 125

Unlock the Seat in an Emergency ...............P. 127Unlock the Ignition Switch in an Emergency ......................................................P. 129

Tyre Puncture ...................................................P. 132Electrical Trouble.............................................P. 133

Battery Goes Dead............................................ P. 133Burned-out Light Bulb ..................................... P. 133Blown Fuse.......................................................... P. 136

Unstable Engine Operation OccursIntermittently .................................................P. 137


Troubleshooting

Engine Will Not Start

Starter Motor Operates ButEngine Does Not StartCheck the following items:● Check the correct engine starting

sequence. 2 P. 59● Check that there is petrol in the fuel tank.● Check if the PGM-FI malfunction indicator

lamp (MIL) is on.u If the indicator lamp is on, contact

your dealer as soon as possible.

Starter Motor Does NotOperateCheck the following items:● Check the correct engine starting

sequence. 2 P. 59● Check for a blown fuse. 2 P. 136● Check for a loose battery connection

(2 P. 91) or battery terminal corrosion(2 P. 81).

● Check the condition of the battery.2 P. 133

If the problem continues, have your vehicleinspected by your dealer.


Troubleshooting

115

Overheating (High coolant temperature indicator is on)The engine is overheating when the followingoccurs:● High coolant temperature indicator

comes on.● Acceleration becomes sluggish.

If this occurs, pull safely to the side of theroad and perform the following procedure.Extended fast idling may cause the highcoolant temperature indicator to come on.

NOTICEContinuing to ride with an overheated enginecan cause serious damage to the engine.

1. Stop the engine using the ignition switch.2. Allow the engine to cool with the ignition

switch in the (Off) position.3. After the engine has cooled, inspect the

radiator hose and check if there is a leak.2 P. 102If there is a leak:Do not start the engine. Transport yourvehicle to your dealer.

4. Check the coolant level in the reservetank. 2 P. 102u Add coolant as necessary.

5. If 1-4 check normal, you may continueriding, but closely monitor the highcoolant temperature indicator.


Troubleshooting

116

Warning Indicators On or Flashing

PGM-FI (Programmed FuelInjection) MalfunctionIndicator Lamp (MIL)Reasons for the indicator lamp to comeon or blink● Comes on if there is a problem with the

engine emissions control system.● Blinks when engine misfiring is detected.

What to do when the indicator lampcomes onAvoid high speeds and immediately get yourvehicle inspected at a dealer.What to do when the indicator lampblinksPark the vehicle in a safe place with noflammable items and wait at least 10 minuteswith the engine stopped until it cools.

NOTICEIf you drive with the malfunction indicator lampon, the emissions control system and the enginecould be damaged.

NOTICEIf the malfunction indicator lamp blinks againwhen restarting the engine, drive to the nearestdealer at 50 km/h (30 mph) or less. Have yourvehicle inspected.


Troubleshooting

117

ABS (Anti-lock Brake System)IndicatorIf the indicator operates in one of thefollowing ways, you may have a seriousproblem with the ABS. Reduce your speedand have your vehicle inspected by yourdealer as soon as possible.

● Indicator comes on or starts flashing whileriding.

● Indicator does not come on when theignition switch is in the (On) position.

● Indicator does not go off at speeds above10 km/h (6 mph).

If the ABS indicator stays on, your brakes willcontinue to work as a conventional system,but without the anti-locking function.

The ABS indicator may flash if you turn therear wheel while the rear wheel is lifted offthe ground. In this case, turn the ignitionswitch to the (Off) position, and then tothe (On) position again. The ABS indicatorwill go off after your speed reaches 30 km/h(19 mph).


Warning Indicators On or Flashing u ABS (Anti-lock Brake System) Indicator

Troubleshooting

118

Torque Control IndicatorIf the indicator operates in one of thefollowing ways, you may have a seriousproblem with the Torque Control. Reduceyour speed and have your vehicle inspectedby your dealer as soon as possible.

● Indicator comes and stays on (solid) whileriding.

● Indicator does not come on when theignition switch is turned to the (On)position.

● Indicator does not go off at speeds above3 km/h (2 mph).

Even when the Torque Control indicator ison, your vehicle will have normal riding abilitywithout Torque Control function.u When the indicator comes on while the

Torque Control is in operation, you willhave to completely close the throttle toregain normal riding ability.

The Torque Control indicator may come on ifyou rotate the rear wheel while your vehicleis lifted off the ground. In this case, turn theignition switch to the (Off) position, andthen to the (On) position again. The TorqueControl indicator will go off after your speedreaches 3 km/h (2 mph).


Warning Indicators On or Flashing u Torque Control IndicatorTroubleshooting

119

Honda SMART Key Indicator# When the Honda SMART Key

indicator flashes 5 timesReplacing the Honda SMART KeyBattery 2 P. 112

# When the Honda SMART Keyindicator is flashing while theignition switch is in the (On)position

The Honda SMART Key indicator flasheswhen communication between your vehicleand Honda SMART Key stops after turningthe ignition switch to the (On) position.It is probably caused by the following:● Strong radio waves or noise are affecting

the system● You lose the Honda SMART Key while

riding

However, this does not affect the operationof your vehicle until the ignition switch islocked.

If you turn the ignition switch to the SEATFUEL, (Off) or (Lock) position while theHonda SMART Key indicator is flashing, theignition switch ring and Honda SMART Keyindicator will come on for about 20 seconds,automatically go off, and then the ignitionswitch is locked.u Turn signals blink at the beginning and

end of this function.Also, to stop this flashing, press and hold theignition switch for more than 2 seconds. Afterthe flashing stops, the ignition switch islocked.

If you do not have the Honda SMART Key,the ignition switch can be unlocked inanother way. 2 P. 129


Warning Indicators On or Flashing u Honda SMART Key Indicator

Troubleshooting

120

Other Warning Indications

Fuel Gauge Failure IndicationIf the fuel system has an error, the fuel gaugeindicators will be displayed as shown in theillustration.If this occurs, see your dealer as soon aspossible.


Troubleshooting

121

When the Idling Stop System Does Not Operate Properly

Idling Stop Indicator Does NotCome OnWhen the Idling Stop indicator does notcome on, perform the followings.

If the Idling Stop switch is at IDLING:Press the Idling Stop switch to IDLING STOP.

If the engine is cold:Warm up the engine.The Idling Stop system does not operatewhen the engine is cold.

If you did not ride the vehicle after enginestarts:Ride the vehicle at speeds of over10 km/h (6 mph). The Idling Stop systemdoes not operate until you ride once.

If PGM-FI malfunction indicator lamp (MIL)lights:When the PGM-FI malfunction indicator lamp(MIL) lights, the Idling Stop system does notoperate for protection of the engine. Seeyour dealer.

If the battery voltage is low:Ride the vehicle awhile, then stop the engineand then restart the engine with start buttonreferring to the starting procedure (2 P. 59)for standard engine starting. The Idling Stopsystem may not operate if the battery voltageis low.If this occurs frequently, contact your dealer.


Troubleshooting

122

Engine is Not Stopped by theIdling Stop System While theIdling Stop Indicator is OnWhen the engine is not stopped by the IdlingStop system while the Idling Stop indicator ison, perform the followings.

If the vehicle does not stop completely:Stop the vehicle completely. The Idling Stopsystem operates if the speed is only at 0 km/h(0 mph).

If the throttle is not closed completely:Close the throttle completely.


When the Idling Stop System Does Not Operate Properly u Engine is Not Stopped by the Idling Stop System While the Idling Stop Indicator is OnTroubleshooting

123

Engine Does Not Start Even Ifthe Throttle is OpenedEngine does not start even if the throttle isopened, perform the followings.

If the side stand is down:While the engine is stopped by the IdlingStop system, if you operate the side stand,the flashing Idling Stop indicator turns off orstops flashing and stays on, and the IdlingStop system is cancelled. Restart the enginewith start button referring to the startingprocedure (2 P. 59) for standard enginestarting.

If the Idling Stop switch is at IDLING:While the engine is stopping by the IdlingStop system, if you press the Idling Stopswitch to IDLING, the Idling Stop system willbe cancelled. Restart the engine with startbutton referring to the starting procedure(2 P. 59) for standard engine starting.

If the Idling Stop indicator flashes (the IdlingStop switch is at IDLING STOP position), butengine does not start even if the throttle isopened, perform the followings.

Low (or dead) battery or battery lead is loose:Check the battery and battery terminals. Ifthe battery is weak, contact your dealer.


When the Idling Stop System Does Not Operate Properly u Engine Does Not Start Even If the Throttle is Opened

Troubleshooting

124

When the Honda SMART Key System Does Not Operate ProperlyWhen the Honda SMART Key system doesnot work properly, perform the following.● Check that the Honda SMART Key system

is activated.Lightly press the ON/OFF button on theHonda SMART Key.If the LED of the Honda SMART Key isred, switch the Honda SMART Key systemto activation. 2 P. 46If the LED of the Honda SMART Key doesnot respond, replace the battery of theHonda SMART Key.

● Check that there is no communicationfailure in the Honda SMART Key system.The Honda SMART Key system uses low-intensity radio waves. The Honda SMARTKey system may not work properly in thefollowing environments:u When there are facilities nearby that

generate strong radio waves or noisesuch as TV towers, power stations,radio stations, or airports.

u When you carry the Honda SMARTKey with a laptop or wirelesscommunication device such as a radioor mobile phone.

u When the Honda SMART Key comesinto contact with or is covered bymetal objects.


Troubleshooting

125Continued

● Check that a registered Honda SMARTKey is used.Use a registered Honda SMART Key.The Honda SMART Key system cannot beactivated without a registered HondaSMART Key.

● Make sure that you do not use a brokenHonda SMART Key.If you use a broken Honda SMART Key,the Honda SMART Key system cannot beactivated. Bring the emergency key andID tag to your dealer.

● Check the battery condition and batterylead in your vehicle.Check the battery and battery terminals. Ifthe battery is weak, contact your dealer.

If the Honda SMART Key system cannot beactivated due to other causes, contact yourdealer.


When the Honda SMART Key System Does Not Operate Properly

Troubleshooting

126

Unlock the Seat in an EmergencyThe seat lock can be unlocked by using theemergency key.

# Open1. Remove the front lid by pushing the side

of the front lid.


Troubleshooting

127Continued

Front lid

Front lid

2. Align the projection of the emergency keywith the slot of the emergency seatopener, and turn the emergency keycounterclockwise.

3. Open the seat and turn the emergencykey clockwise.

# Close1. Close and push down on the rear of the

seat until it locks. Make sure that the seatis locked securely by pulling it up lightly. Ifthe seat is not locked, turn the emergencykey clockwise to lock the seat catch.

2. Install the front lid in the reverse order ofremoval.


Unlock the Seat in an Emergency

Troubleshooting

128

Emergency key

Open

Close

Emergency seatopener

Projection

Slot

Unlock the Ignition Switch in an Emergency

# Set up to ID number input mode1. Use the emergency key to open the seat.

2 P. 1272. Remove the battery cover. 2 P. 933. Pull out the EM mode connector.4. Remove the blue dummy coupler by

releasing the tab of the EM modeconnector while lifting the hook of theblue dummy coupler.

5. Check the ID number on the ID tag.6. Connect the EM mode coupler provided

in the tool kit to the EM mode connector.


Troubleshooting

129Continued

Tab Hook

EM modecoupler

Blue dummycoupler

EM modeconnector

ID number

# ID number inputYou can input your ID number by pressing theignition switch when the ignition switch is inthe (Off), (Lock) or SEAT FUEL position.Input the ID number on the ID tag in orderfrom the left in turn by pressing the ignitionswitch.The ID number is authenticated according tothe number of times the ignition switch ispushed.Push the ignition switch the desired numberof times within 5 seconds when the ignitionswitch ring comes on. After 5 seconds, theignition switch ring goes off and comes onagain. This means that the inputted numberis fixed, and you can input the next number.u If the ignition switch ring does not come

on in blue, the battery may be low.Contact your dealer.

Example:● To input “0”, wait for 5 seconds without

pushing the ignition switch when theignition switch ring comes on.

● To input “1”, push the ignition switch oncewithin 5 seconds when the ignition switchring comes on.


Unlock the Ignition Switch in an Emergency

Troubleshooting

130

To input “0”

To input “1”

ID number

Ignition switch

No push

Ignition switch

ID number Push one time

ID number input successAfter the last ID number is inputted, through,the ignition switch ring and Honda SMARTKey Indicator will flash every 2 seconds untilthe EM mode coupler is removed.Be sure to remove the EM mode coupler andreturn the blue dummy coupler. The ignitionswitch is then unlocked. Reinstall the parts inreverse order of removal and turn the ignitionswitch to the (On) position within 6 minutes. Youcan start the engine.To lock the ignition switch, turn the ignition switchto the SEAT FUEL, (Off), or (Lock) position,and press and hold the ignition switch for 2seconds. The ignition switch also locksautomatically when the ignition switch has been inthe SEAT FUEL, (Off), or (Lock) position forabout 6 minutes after the ID number issuccessfully inputted.When the ignition switch is locked, the ignitionswitch ring goes off.

To unlock the ignition switch again, repeat theprocedure for unlocking the ignition switch.ID number input failureAfter the last ID number is inputted, theignition switch ring and Honda SMART KeyIndicator will flash every second until the EMmode coupler is removed, and the ignitionswitch cannot be unlocked.Pull out the EM mode coupler and reconnectit to the EM mode connector. Follow theprocedure again. 2 P. 130ID number input cancelPull out the EM mode coupler from the EMmode connector.Also, if you make a mistake while inputting theID number, remove the EM mode coupler fromthe EM mode connector, connect it to the EMmode connector again, and then re-input theID number from the beginning.

● Store the removed EM mode coupler inthe tool kit at all times.


Unlock the Ignition Switch in an EmergencyTroubleshooting

131

Tyre PunctureRepairing a puncture or removing a wheelrequires special tools and technical expertise.We recommend you have this type of serviceperformed by your dealer.After an emergency repair, always have thetyre inspected/replaced by your dealer.

Emergency Repair Using a TyreRepair KitIf your tyre has a minor puncture, you canmake an emergency repair using a tubelesstyre repair kit.Follow the instructions provided with theemergency tyre repair kit.Riding your vehicle with a temporary tyrerepair is very risky. Do not exceed 50 km/h(30 mph). Have the tyre replaced by yourdealer as soon as possible.

3WARNINGRiding your vehicle with a temporarytyre repair can be risky. If the temporaryrepair fails, you can crash and beseriously injured or killed.

If you must ride with a temporary tyrerepair, ride slowly and carefully and donot exceed 50 km/h (30 mph) until thetyre is replaced.


Troubleshooting

132

Electrical Trouble

Battery Goes DeadCharge the battery using a motorcyclebattery charger.Remove the battery from the vehicle beforecharging.Do not use an automobile-type batterycharger, as these can overheat a motorcyclebattery and cause permanent damage. If thebattery does not recover after recharging,contact your dealer.

NOTICEJump starting using an automobile battery candamage your vehicle's electrical system and isnot recommended.

Burned-out Light BulbAll light bulbs on the vehicle are LEDs. Ifthere is an LED which is not turned on, seeyour dealer for servicing.


Troubleshooting

133Continued

# Headlight/Front Turn Signals/Position Light

The headlight/front turn signals use severalLEDs.The position light uses a several LED.If there is an LED which is not turned on, seeyour dealer for servicing.


Electrical Trouble u Burned-out Light Bulb

Troubleshooting

134

Headlight

Position light

Front turnsignals

# Brakelight/Taillight/Rear TurnSignals/License Plate Light

The brakelight/taillight/rear turn signals useseveral LEDs.The license plate light uses a several LED.If there is an LED which is not turned on, seeyour dealer for servicing.


Electrical Trouble u Burned-out Light BulbTroubleshooting

135

Brakelight/Taillight

License platelight

Rear turnsignal

Rear turnsignal

Blown FuseBefore handling fuses, see “Inspecting andReplacing Fuses.” 2 P. 83

# Fuse Box Fuses1. Remove the battery cover. 2 P. 932. Remove the fuse box cover.3. Pull the fuses out one by one with the

fuse puller located back side of the fusebox cover. Check for a blown fuse. Alwaysreplace a blown fuse with a spare fuse ofthe same rating.u Spare fuses are provided on the back

side of the fuse box cover.4. Install the fuse box cover.5. Install the battery cover. NOTICE

If a fuse fails repeatedly, you likely have anelectrical problem. Have your vehicle inspectedby your dealer.


Electrical Trouble u Blown Fuse

Troubleshooting

136

Fuse box cover

Fuse puller

Spare fuses

Spare fuses

Main fuse

Unstable Engine Operation Occurs IntermittentlyIf the fuel pump filter is clogged, unstableengine operation will occur intermittentlywhile riding.Even if this symptom occurs, you cancontinue to ride your vehicle.If unstable engine operation occurs even ifsufficient fuel is available, have your vehicleinspected by your dealer as soon as possible.


Troubleshooting

137

Service Diagnostic Recorders.......................P. 139Keys.....................................................................P. 139Instruments, Controls, & Other Features...P. 143Caring for Your Vehicle..................................P. 143Storing Your Vehicle.......................................P. 146Transporting Your Vehicle ............................P. 147You & the Environment .................................P. 148Serial Numbers ................................................P. 149Fuels Containing Alcohol ..............................P. 150Catalytic Converter .........................................P. 151


Information

Service DiagnosticRecordersYour vehicle is equipped with service-relateddevices that record information aboutpowertrain performance and riding conditions.The data can be used to help techniciansdiagnose, repair and maintain the vehicle. Thisdata may not be accessed by anyone elseexcept as legally required or with the permissionof the vehicle owner.However this data may be accessed by Honda,its authorised dealers and authorised repairers,employees, representatives and contractors onlyfor the purpose of the technical diagnosis,research and development of the vehicle.

KeysEmergency Key

The emergency key is used for an emergency.● To unlock the seat. 2 P. 127● To unlock the ignition switch. 2 P. 129

Do not store the emergency key in anycompartment.


Service Diagnostic RecordersInform

ation

139Continued

Emergency key

Honda SMART KeyCarrying the Honda SMART Key allows you toperform the following operations:• Locking or unlocking the ignition switch• Releasing the seat lock• Opening the fuel lid.• Locking or unlocking the steering

The ID number of the Honda SMART Key is onthe ID tag. You can also unlock the ignitionswitch by inputting the ID number.

Always carry both the emergency key and IDtag, but separate from the Honda SMART Key,to avoid losing all of them at the same time.

Also store a copy of your ID number in a safeplace other than your vehicle.

The Honda SMART Key contains electroniccircuits. If the circuits are damaged, the HondaSMART Key will not allow you to perform anyoperations.

● Do not drop the Honda SMART Key or setheavy objects on them.

● Protect the Honda SMART Key from directsunlight, high temperature, and highhumidity.

● Do not scratch or puncture.● Do not store near any magnetized products

such as a magnetized key chain.● Always keep the Honda SMART Key away

from electric appliances such as a TV, radio,PC or low-frequency massage device.


Keys

Information

140

● Keep the Honda SMART Key away fromliquids. If it gets wet, dry it immediately witha soft cloth.

● Keep the Honda SMART Key away from thevehicle while washing the vehicle.

● Do not burn.● Do not wash in the ultrasonic cleaner.● If fuel, wax, or grease adhere to the Honda

SMART Key, wipe it off immediately to avoidcracking or warping.

● Do not disassemble the Honda SMART Keyother than when changing a battery. Onlythe cover of the Honda SMART Key can bedisassembled. Do not disassemble otherparts.

● Do not lose your Honda SMART Key. If youlose it, you will need to register a newHonda SMART Key. See your dealer withyour emergency key and ID tag forregistration.

The battery in the Honda SMART Key systemnormally lasts about 2 years.

Do not keep mobile phones or other radiotransmitting devices in any compartment. Theradio frequency from the devices will interruptthe Honda SMART Key system.

To get an additional Honda SMART Key, takethe Honda SMART Key and the vehicle to yourdealer.


KeysInform

ation

141Continued

EU DirectiveThis Honda SMART Key system complies withthe RE (Radio Equipment) Directive (2014/53/EU).

The declaration of conformity to RE Directive isprovided to the owner at the time of purchase.The declaration of conformity should be kept ata safe place. When the declaration ofconformity is lost or is not provided, contactyour dealer.South Africa only Singapore only

Morocco only


Keys

Information

142

Honda SMART Key ID tag

Instruments, Controls, &Other FeaturesIgnition Switch

Leaving the ignition switch in the (On) positionwith the engine stopped will drain the battery.

Do not turn the ignition switch while riding.

OdometerThe display locks at 999,999 when the read-outexceeds 999,999.

TripmeterThe tripmeters return to 0.0 when each read-out exceeds 9,999.9.

Document BagThe owner’s manual, registration, and insuranceinformation can be stored in the plasticdocument bag in the centre compartment.

Caring for Your VehicleFrequent cleaning and polishing is important toensure the life of your Honda. A clean vehiclemakes it easier to spot potential problems.In particular, seawater and salts used to preventice on roads promote the formation ofcorrosion. Always wash your vehicle thoroughlyafter riding on coastal or treated roads.

WashingAllow the engine, muffler, brakes, and otherhigh-temperature parts to cool before washing.1. Rinse your vehicle thoroughly using a low

pressure garden hose to remove loose dirt.2. If necessary, use a sponge or a soft towel

with mild cleaner to remove road grime.u Clean the headlight lens, panels, and

other plastic components with extra careto avoid scratching them.Avoid directing water into the air cleaner,muffler, and electrical parts.


Instruments, Controls, & Other FeaturesInform

ation

143Continued

3. Thoroughly rinse your vehicle with plenty ofclean water and dry with a soft, clean cloth.

4. After the vehicle dries, lubricate any movingparts.u Make sure that no lubricant spills onto

the brakes or tyres. Brake discs, pads,drum or shoes contaminated with oil willsuffer greatly reduced brakingeffectiveness and can lead to a crash.

5. Apply a coat of wax to prevent corrosion.u Avoid products that contain harsh

detergents or chemical solvents. Thesecan damage the metal, paint, and plasticon your vehicle.Keep the wax clear of the tyres and brakes.

u If your vehicle has any mat painted parts,do not apply a coat of wax to the matpainted surface.

# Washing PrecautionsFollow these guidelines when washing:● Do not use high-pressure washers:

u High-pressure water cleaners candamage moving parts and electricalparts, rendering them inoperable.

u Water in the air intake can be drawn intothe throttle body and/or enter the aircleaner.

● Do not direct water at the muffler:u Water in the muffler can prevent starting

and causes rust in the muffler.● Dry the brakes:

u Water adversely affects brakingeffectiveness. After washing, apply thebrakes intermittently at low speed tohelp dry them.

● Do not direct water under the seat:u Water in the under seat compartment

can damage your documents and otherbelongings.


Caring for Your Vehicle

Information

144

● Do not direct water at the air cleaner:u Water in the air cleaner can prevent the

engine from starting.● Do not direct water near the headlight:

u The headlight's inside lens may fogtemporarily after washing or while ridingin the rain. This does not impact theheadlight function.However, if you see a large amount ofwater or ice accumulated inside thelens(es), have your vehicle inspected byyour dealer.

● Do not use wax or polishing compounds onmat painted surface:u Use a soft cloth or sponge, plenty of

water, and a mild detergent to clean matpainted surfaces. Dry with a soft cleancloth.

Aluminium ComponentsAluminium will corrode from contact with dirt,mud, or road salt. Clean aluminium partsregularly and follow these guidelines to avoidscratches:● Do not use stiff brushes, steel wool, or

cleaners containing abrasives.● Avoid riding over or scraping against curbs.

PanelsFollow these guidelines to prevent scratchesand blemishes:● Wash gently using a soft sponge and plenty

of water.● To remove stubborn stains, use diluted

detergent and rinse thoroughly with plentyof water.

● Avoid getting petrol, brake fluid, ordetergents on the instruments, panels, orheadlight.


Caring for Your VehicleInform

ation

145Continued

Exhaust Pipe and MufflerWhen the exhaust pipe and muffler are painted,do not use a commercially available abrasivekitchen cleaning compound. Use a neutraldetergent to clean the painted surface on theexhaust pipe and muffler. If you are not sure ifyour exhaust pipe and muffler are painted,contact your dealer.

Storing Your VehicleIf you store your vehicle outdoors, you shouldconsider using a full-body cover.If you won't be riding for an extended period,follow these guidelines:● Wash your vehicle and wax all painted

surfaces (except mat painted surfaces). Coatchrome pieces with rust-inhibiting oil.

● Place your vehicle on its centre stand andposition a block so that both tyres are offthe ground.

● After rain, remove the body cover and allowthe vehicle to dry.

● Remove the battery (2 P. 91) to preventdischarge. Fully charge the battery and thenplace it in a shaded, well-ventilated area.u If you leave the battery in place,

disconnect the negative - terminal toprevent discharge.

After removing your vehicle from storage,inspect all maintenance items required by theMaintenance Schedule.


Storing Your Vehicle

Information

146

Transporting Your VehicleIf your vehicle needs to be transported, itshould be carried on a motorcycle trailer or aflatbed truck or trailer that has a loading rampor lifting platform, and motorcycle tie-downstraps. Never try to tow your vehicle with awheel or wheels on the ground.

NOTICETowing your vehicle can cause serious damageto the transmission.


Transporting Your VehicleInform

ation

147

You & the EnvironmentOwning and riding a vehicle can be enjoyable,but you must do your part to protect theenvironment.

Choose Sensible CleanersUse a biodegradable detergent when you washyour vehicle. Avoid aerosol spray cleaners thatcontain chlorofluorocarbons (CFCs) whichdamage the atmosphere's protective ozonelayer.

Recycle WastesPut oil and other toxic wastes in approvedcontainers and take them to a recycling centre.Call your local or state office of public works orenvironmental services to find a recycling centrein your area, and to get instructions on how todispose of non-recyclable wastes. Do not placeused engine oil in the trash, or pour it down adrain or on the ground. Used oil, petrol,coolant, and cleaning solvents contain poisonsthat can hurt refuse workers and contaminatedrinking water, lakes, rivers, and oceans.


You & the Environment

Information

148

Serial NumbersThe frame and engine serial numbers uniquelyidentify your vehicle and are required in orderto register your vehicle. They may also berequired when ordering replacement parts.You should record these numbers and keepthem in a safe place.


Serial NumbersInform

ation

149

Frame number

Engine number

Fuels Containing AlcoholSome conventional fuels blended with alcoholare available in some locales to help reduceemissions to meet clean air standards. If youplan to use blended fuel, check that it isunleaded and meets the minimum octanerating requirement.

The following fuel blends can be used in yourvehicle:● Ethanol (ethyl alcohol) up to 10% by volume.

u Petrol containing ethanol may bemarketed under the name Gasohol.

The use of petrol containing more than 10%ethanol may:● Damage the painting of the fuel tank.● Damage the rubber tubes of the fuel line.● Cause corrosion of the fuel tank.● Cause poor drivability.NOTICEUse of blended fuels containing higher thanapproved percentages can damage metal,rubber, plastic parts of your fuel system.

If you notice any undesirable operatingsymptoms or performance problems, try adifferent brand of petrol.


Fuels Containing Alcohol

Information

150

Catalytic ConverterSH125ADThis vehicle is equipped with a three-waycatalytic converter. The catalytic convertercontains precious metals that serve as catalystsin high temperature chemical reactions thatconvert hydrocarbons (HC), carbon monoxide(CO), and oxides of nitrogen (NOx) in theexhaust gasses into safe compounds.

SH150ADThis vehicle is equipped with two three-waycatalytic converters. Each catalytic convertercontains precious metals that serve as catalystsin high temperature chemical reactions thatconvert hydrocarbons (HC), carbon monoxide(CO), and oxides of nitrogen (NOx) in theexhaust gasses into safe compounds.

A defective catalytic converter contributes to airpollution and can impair your engine'sperformance. A replacement unit must be anoriginal Honda part or equivalent.

SH125ADFollow these guidelines to protect your vehicle'scatalytic converter.● Always use unleaded petrol. Leaded petrol

will damage the catalytic converter.● Keep the engine in good running condition.● Have your vehicle serviced if your engine is

misfiring, backfiring, stalling, or otherwisenot running properly, stop riding and turnoff the engine.

SH150ADFollow these guidelines to protect your vehicle'scatalytic converters.● Always use unleaded petrol. Leaded petrol

will damage the catalytic converters.● Keep the engine in good running condition.● Have your vehicle serviced if your engine is

misfiring, backfiring, stalling, or otherwisenot running properly, stop riding and turnoff the engine.


Catalytic ConverterInform

ation

151

Specifications■ Main ComponentsOverall length 2,090 mm (82.3 in)Overall width 730 mm (28.7 in)Overall height 1,130 mm (44.5 in)Wheelbase 1,350 mm (53.1 in)Minimum groundclearance 145 mm (5.7 in)

Caster angle 26º 00’Trail 86 mm (3.4 in)

Curb weight

Ⅱ ED, Ⅲ ED type138 kg (304 lb)Except Ⅱ ED, Ⅲ ED type137 kg (302 lb)

Maximum weight capacity*1 180 kg (397 lb)

Maximum luggage weight

Centrecompartment 10 kg (22 lb)

Shoppinghook 1.5 kg (3.3 lb)

Rear carrier 3 kg (6.6 lb)Passenger capacity Rider and 1 passengerMinimum turning radius 2.00 m (6.6 ft)*1 : Including rider, passenger, all luggage, and accessories.

Displacement SH125AD 125 cm3 (7.6 cu-in)SH150AD 157 cm3 (9.6 cu-in)

Bore x stroke SH125AD 53.5 x 55.5 mm (2.11 x 2.19 in)SH150AD 60.0 x 55.5 mm (2.36 x 2.19 in)

Compressionratio

SH125AD 11.5:1SH150AD 12.0:1

Fuel Unleaded petrolRecommended: 95 RON or higher

Fuel containingalcohol ETHANOL up to 10 % by volume

Tank capacity 7.0 L (1.85 US gal, 1.54 Imp gal)

Battery YTZ8V12 V-7.0 Ah (10 HR) / 7.4 Ah (20 HR)

Primaryreduction V-Matic (2.68:1 ~ 0.82:1)

Final reduction SH125AD 11.423SH150AD 10.552


Specifications

152

■ Service DataTyre size Front 100/80-16M/C 50P

Rear 120/80-16M/C 60PTyre type Bias-ply, tubeless

RecommendedTyre

Front IRC SS-530FMICHELIN CITY GRIP

Rear IRC SS-530RMICHELIN CITY GRIP

Tyre category ofuse *1

Normal PermittedSpecial Not PermittedSnow Not PermittedMoped Not Permitted

Tyre airpressure(Driver only)


Tyre air pressure(Driver andpassenger)


Minimum treaddepth

Front 1.5 mm (0.06 in)

Rear 2.0 mm (0.08 in)(SH150AD only)Spark plug (standard) LMAR8L-9 (NGK)Spark plug gap 0.8 - 0.9 mm (0.03 - 0.04 in)Idle speed 1,700 ± 100 rpm

Recommendedengine oil

Honda 4-stroke motorcycle oil API ServiceClassification SG or higher, excluding oilsmarked as “Energy Conserving” or “ResourceConserving, ”SAE 10W-30, JASO T 903standard MB

Engine oilcapacity

After draining 0.8 L (0.8 US qt, 0.7 Imp qt)After draining& cleaningstrainer screen

0.9 L (1.0 US qt, 0.8 Imp qt)

Afterdisassembly 0.9 L (1.0 US qt, 0.8 Imp qt)

Transmissionoil capacity

After draining 0.12 L (0.13 US qt, 0.11 Imp qt)Afterdisassembly 0.14 L (0.15 US qt, 0.12 Imp qt)

Recommendedbrake fluid Honda DOT 3 or DOT 4 Brake Fluid

Cooling systemcapacity 0.47 L (0.50 US qt, 0.41 Imp qt)

Recommendedcoolant Pro Honda HP Coolant

*1 : EU regulation


SpecificationsSpecifications

153

■ BulbsHeadlight LEDBrakelight/Taillight LEDFront turn signal LEDRear turn signal LEDLicense plate light LEDPosition light LED

■ FusesMain fuse 20 AOther fuse 30 A, 15 A, 10 A, 7.5 A

■ Torque SpecificationsOil plug 20 N·m (2.0 kgf·m, 15 lbf·ft)Engine oil drain bolt 24 N·m (2.4 kgf·m, 18 lbf·ft)


Specifications

Specifications

154

IndexAABS (Anti-lock Brake System)....................... 12ABS (Anti-lock Brake System) Indicator .................................................. 41, 118

Accessories ........................................................ 16Answer Back System ....................................... 53Available Driving Distance ...................... 23, 26Average Fuel Mileage............................... 23, 27

BBattery.......................................................... 81, 91Battery Voltage Meter.............................. 23, 28Brakes

Fluid.............................................................. 85, 105Pad Wear ........................................................... 106

Braking ............................................................... 11Bulb

Brakelight/Taillight........................................... 135Front Turn Signal ............................................. 134Headlight ........................................................... 134License Plate Light........................................... 135Position Light .................................................... 134Rear Turn Signal............................................... 135

CCaring for Your Vehicle................................ 143Catalytic Converter........................................ 151Centre Compartment...................................... 71Clock............................................................. 23, 33Compartment

Document Bag ................................................. 143Owner’s Manual............................................... 143

Coolant............................................................. 102Crankcase Breather................................. 86, 109Current Fuel Mileage................................ 23, 25

DDigital Clock Adjustment............................... 33Document Bag ......................................... 72, 143

EElectrical Trouble ........................................... 133Emergency

Emergency Key................................................. 139Unlock the Ignition Switch............................. 129Unlock the Seat ................................................ 127


Index

155

EngineNumber.............................................................. 149Oil.................................................................... 84, 98Oil Strainer Screen............................................. 99Overheats .......................................................... 116Starting ................................................................. 59

Environment ................................................... 148

FFlooded Engine ................................................ 59Frame Number ............................................... 149Fuel

Gauge ............................................................ 23, 28Recommended.......................................... 64, 152Remaining............................................................ 28Tank Capacity ............................................ 64, 152

Fuels Containing Alcohol............................. 150Fuses........................................................... 83, 136

GGasohol ............................................................ 150

HHeadlight Aim ................................................ 110

Headlight Dimmer Switch ............................. 42Helmet Holder.................................................. 70High Coolant Temperature Indicator ......... 40Honda Selectable Torque Control......... 15, 58Honda SMART Key........................................ 140Honda SMART Key Battery ......................... 112Honda SMART Key Indicator................ 40, 120Honda SMART Key System ........................... 45Horn Button ...................................................... 42

IIdling Stop Indicator....................................... 40Idling Stop Switch ........................................... 42Idling Stop System .......................................... 55Ignition Cut-off System

Side Stand ......................................................... 107Ignition Switch......................................... 43, 143Image Labels ....................................................... 6Indicators........................................................... 40INFO A button............................................ 22, 42INFO B button ............................................ 22, 42Instruments ....................................................... 22


Index

156

KKey

Emergency Key................................................. 139Honda SMART Key.......................................... 140

LLabels.................................................................... 6Load Limits ........................................................ 17Loading Guidelines.......................................... 17

MMaintenance

Fundamentals ..................................................... 79Importance .......................................................... 75Safety .................................................................... 75Schedule............................................................... 76

Maintenance Indicator............................. 23, 31Maximum Luggage Weight .................... 9, 152Maximum Weight Limit......................... 17, 152Modifications.................................................... 16

OOdometer............................................ 23, 25, 143Oil

Engine ............................................................ 84, 98Oil Change Indicator................................. 23, 30Overheating .................................................... 116

PParking ............................................................... 12Parts Location................................................... 20Passing Light Control Switch ........................ 42Petrol.................................................... 14, 64, 152PGM-FI (Programmed Fuel Injection)Malfunction Indicator Lamp (MIL).... 40, 117

Protective Apparel........................................... 10

RRear Carrier ....................................................... 73Rear Suspension ............................................ 111Recommended

Coolant........................................................ 85, 153Fuel............................................................... 64, 152Oil .......................................................................... 84

Refuelling........................................................... 64


Index

157

RemovalBattery................................................................... 91Battery Cover ...................................................... 93Clip......................................................................... 94Maintenance Lid................................................. 95

Repair Kit ......................................................... 132Riding Precautions .......................................... 11

SSafety Precautions........................................... 10Seat ..................................................................... 69Serial Numbers............................................... 149Shopping Hook ................................................ 73Side Stand ....................................................... 107Side Stand Ignition Cut-off System.... 59, 107Spark Plug ......................................................... 96Specifications.................................................. 152Speedometer .................................................... 23Start Button....................................................... 42Starting the Engine ......................................... 59Steering Lock .................................................... 44Storage

Centre Compartment........................................ 71Document Bag.................................................... 72

Equipment ........................................................... 69Owner’s Manual ................................................. 72Rear Carrier ......................................................... 73Shopping Hook .................................................. 73Tool Kit.................................................................. 72

Storing.............................................................. 146Switches ............................................................. 42

TThrottle ............................................................ 108Tool ..................................................................... 90Tool Kit......................................................... 72, 90Torque Control Indicator ...................... 41, 119Torque Control mode display ................ 23, 28Torque Control OFF Indicator....................... 41Transporting ................................................... 147Tripmeter ............................................ 23, 26, 143Troubleshooting ............................................ 114Turn Signal Indicators .................................... 41Turn Signal Switch........................................... 42Tyres

Air Pressure............................................ 9, 86, 153Puncture............................................................. 132Replacing ............................................................. 86


Index

158

UUSB Socket ........................................................ 67

WWarning Indicators On or Flashing ........... 117Washing Your Vehicle .................................. 143Weight Limit............................................. 17, 152


Index

159

SH125i/SH

150i

SH125i/SH150i

XXX.XXXX.XX.LPRINTED IN XXXXX

OWNER’S MANUAL

32K0RA0000X32-K0R-A000

EN

Documents

OWNER’S MANUAL - Honda