Panasonic UF-9000-DP-180-190_HB_Ver2.0_040628

Order Number: MGCS040602C0J7

FacsimileUF-9000

DP-180/190

[ Version 2.0 ]

This service information is designed for experienced repair technicians only and is not intended for use by the general public.It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the product or products dealt within this service information by anyone else could result in serious injury or death.

WARNING

© 2004 Panasonic Communications Co., Ltd. All rights reserved. Unauthorized copying and distribution isa violation of law.

ject to change

vements in

Information regarding Lead-Free (PbF) solder:

Distinction of PbF PCB:PCBs (manufactured) using lead free solder will have a mark following

typically oldering iron Exercise care PCB for too long

100 F/600 C).Ltd.: PbF PCBs.

This Product Uses Lead (Pb) Free Solder Printed Circuit Boards (PCBs).

2

The contents of this Service Handbook and the Specifications are subwithout notice. Panasonic Communications Co., Ltd. reserves the right to make improthe product design without reservation and without notice.Published in Japan.

the PCB part numbers in a label on the PCB. Caution:

Pb free solder has a higher melting point than standard solder; the melting point is 50 - 70 F (30 - 40 C) higher. Please use a s with temperature control and adjust it to 700 20 F (370 10 C). while using higher temperature soldering irons, do not heat the to prevent solder splash or damage to the PCB. Pb free solder will tend to splash when heated too high (about 1 ECO SOLDER M705 (available from Senju Metal Industry Co.,

URL: http://www.senju-m.co.jp) is recommended when repairing

3

Important NoticePlease read this notice completely BEFORE repairing or installing any optional accessories. As failure to properly install the additional board or connector with the power ON could damage the machine's SPC or SC board.Please follow the instructions below:1. It is essential that you turn OFF the Main Power Switch located on the Left Side of the machine.2. It is essential that you unplug the AC Power Cord from the wall outlet. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord.)3. Please read the installation instructions carefully and follow each step.

<Example: UF-9000>

Note:O = Power OFF, l = Power ON

Note:If the Hard Disk Drive Unit is installed, to prevent a Scan Disk Function from beingperformed (similar to Windows OS when the power is abruptly interrupted), it isimportant to follow the step sequence below when turning OFF the Power Switch on themachine.1. If the machine is in the "ENERGY SAVER (Shutdown Mode)", you may turn the Power Switch on the Left Side of the machine to the OFF position. If it is not in the "ENERGY SAVER (Shutdown Mode)", continue to step 2 below.2. Press "FUNCTION" and "ENERGY SAVER" keys simultaneously first.3. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk Drive Unit and advances into "ENERGY SAVER MODE".4. Turn the Power Switch on the Left Side of the machine to the OFF position.5. Unplug the AC Power Cord. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord.)

* The specifications are subject to change without notice. Panasonic Communications Co., Ltd. reserves the right to make improvements in the product design without reservation and without notice.

4

Power and Ground Connection Cautions

Ensure that the plug connection is free of dust. In a damp environment, a contaminatedconnector can draw a significant amount of current that can generate heat andeventually cause fire over an extended period of time.

Always use the power cord provided with your machine. When an extension power cordis required, always use a properly rated cord.

120 V/15 A or AC 220 - 240V/10 AIf you use a cord with an unspecified current rating, the machine or plug may emit smokeor become hot to the touch externally.

Do not attempt to rework, pull, bend, chafe or otherwise damage the power cord. Do notplace a heavy object on the cord. A damaged cord can cause fire or electric shocks.

For Your SafetyTo prevent severe injury and loss of life, read this section carefully before servicing the Panasonicmachine to ensure proper and safe operation.Please ensure that the machine is installed near a wall outlet and is easily accessible.

This section explains the graphic symbols used in the machine and/or this manual.

WARNING:Denotes a potential hazard that could result in serious injury or death.

CAUTION:Denotes hazards that could result in minor injury or damage to the machine.

This section also explains the graphic symbols used in the machine and/or this manual.

These symbols are used to alert operators to a specific operating procedurethat must not be performed.

These symbols are used to alert operators to a specific operating procedurethat must be emphasized in order to operate the machine safely.

Installation and Relocation Cautions

Do not place the machine near heaters or volatile, flammable, or combustible materialssuch as curtains that may catch fire.

Do not place the machine in a hot, humid, dusty or poorly ventilated environment.Prolonged exposure to these adverse conditions can cause fire or electric shocks.

Place the machine on a level and sturdy surface that can with stand.If tilted, the machine may tip-over and cause injuries.

When relocating the machine, remove the toner and/or developer, and pack the machine with proper packing materials for shipping.

When moving the machine, be sure to unplug the power cord from the outlet. If themachine is moved with the power cord attached, it can cause damage to the cord whichcould result in fire or electric shock.

Precautions

CAUTION

WARNING

5

Never touch a power cord with wet hands. Danger of electric shock exists.

If the power cord is broken or insulated wires are exposed, replace immediately with a specified cord only.Using a damaged cord can cause fire or electric shocks.

Stop operation immediately if your machine produces smoke, excessive heat, unusual noise, or smell,or if water is spilt onto the machine. These conditions can cause fire. Immediately switch Off andunplug the machine.

Do not disconnect or reconnect the machine while it is on. Disconnecting a live connector can deformthe plug and cause fire.

When disconnecting the machine, grasp the plug instead of the cord. Forcibly pulling on a cord candamage it and cause fire or electric shock.

When the machine is not used over an extended period of time, switch it Off and unplug it. If an unusedmachine is left connected to a power source for a long period, degraded insulation can cause electricshocks, current leakage or fire.

Be sure to switch Off and unplug the machine before accessing the interior of the machine for cleaning,maintenance or fault clearance. Access to a live machines interior can cause electric shock.

Be sure to switch Off and unplug the machine before accessing the interior of the machine foraccessing interface cables, maintenance or fault clearance. Access to a live machines interior cancause electric shock.

Once a month, unplug the machine and check the power cord for the following. If you notice anyunusual condition.

The power cord is plugged firmly into the receptacle.The plug is not excessively heated, rusted, or bent.The plug and receptacle are free of dust.The cord is not cracked or frayed.

OthersThe machine has a built-in circuit for protection against lightning-induced surge current. If lightning strikes in yourneighborhood, switch Off the machine. Disconnect the telephone line cable first, then unplug the power cord from the machine and reconnect only when the lightning storm has stopped.If you notice flickering or distorted images or noises on your audio-visual units, your machine may be causingradio interference. Switch it Off and if the interference disappears, the machine is the cause of the radio interfer-ence. Perform the following procedure until the interference is corrected.

Move the machine and the TV and/or radio away from each other.Reposition or reorient the machine and the TV and/or radio.Unplug the machine, TV and/or radio, and replug them into outlets that operate on different circuits.Reorient the TV and/or radio antennas and cables until the interference stops. For an outdoor antenna, ask your local electrician for support.Use a coaxial cable antenna.

Operating Safeguards

Do not touch areas where these caution labels are attached to the surface may be very hot, and causeserver burns.

Do not place any liquid container such as a vase or coffee cup on the machine. Spilt water can causefire or shock hazard.

Do not place any metal parts such as staples or clips on the machine. If metal and flammable parts getinto the machine, they can short-circuit internal components, and cause fire or electric shocks.

If debris (metal or liquid) gets into the machine, switch Off and unplug the machine.Operating a debris-contaminated machine can cause fire or electric shock.

Do not try to alter the machine configuration or modify any parts. An unauthorized modification cancause smoke or fire.

WARNING

6

Do not place a magnet near the safety switch of the machine. A magnet can activate themachine accidentally resulting in injuries.

Do not use a highly flammable spray or solvent near the machine. It can cause fire.

When copying a thick document, do not use excessive force to press it against thedocument glass. The glass may break and cause injuries.

Never touch a labeled area found on or near the heat roller. You can get burnt. If a sheetof paper is wrapped around the heat roller, do not try to remove it when it is hot, to avoidinjuries or burns. Switch Off the machine immediately, and wait until it cools down.

Do not use conductive paper, e.g. folding paper, carbonic paper and coated paper. Whena paper jam occurs, they can cause a short circuit and fire.

Do not place any heavy object on the machine. An off-balance machine can tip-over orthe heavy object can fall, causing damage and/or injuries.

Keep the room ventilated when using the machine for an extended period of time tominimize the ozone density in the air.

When copying with the document cover open, do not look directly at the exposure lamp.Direct eye exposure can cause eye fatigue or damage.

Pull out paper trays slowly to prevent injuries.

When removing jammed paper, make sure that no pieces of torn paper are left in themachine. A piece of paper remaining in the machine can cause fire. If a sheet of paper iswrapped around the heat roller, or when clearing a jammed paper that is difficult orimpossible to see, do not try to remove it by yourself. Doing so can cause injuries orburns. Switch Off the machine immediately, and wait until it cools down.

CAUTION

Consumable Safeguards

Never throw a toner cartridge into an open flame. Toner remaining in the cartridge cancause an explosion and you can get burnt.

Never throw toner or a waste toner container or a toner cartridge into an open flame. Itcan cause an explosion and you can get burnt.

Keep button batteries out of the reach of children. If a button battery is swallowedaccidentally, get medical treatment immediately.

Never heat the drum cartridge, or scratch its surface. A heated or scratched drum can behazardous to your health.

Do not mix new and old batteries together. Otherwise, batteries can burst or leak,causing fire or injuries.

Be sure to use the specified type of batteries only.

Ensure that batteries are installed with correct polarity. Incorrectly installed batteries canburst or leak, resulting in spillage or injuries.

WARNING

CAUTION

Table of Contents

7

Specifications Table ................................81.1. Copy Function...........................................81.2. Fax, Printer and Internet

Fax Functions .........................................161.3. System Combination...............................261.4. Options List.............................................27

Maintenance, Adjustments and Check Points ..........................................28

2.1. Preventive Maintenance .........................282.2. Required Tools .......................................302.3. Preventive Maintenance Points ..............312.4. Preventive Maintenance Check List .......322.5. Updating the Firmware ...........................332.6. Adjusting the Printer Registration,

LSU Image Side to Side .........................42

Troubleshooting ....................................443.1. Error Codes (For Copier) ........................443.2. Information Code Table

(For Facsimile)........................................51

Service Modes........................................584.1. Service Modes (For Copier)....................584.2. Service Modes (For Facsimile) ...............75

Exploded View & Parts List ................1065.1. Destination Codes ................................1075.2. Control Panel Unit.................................1085.3. Scanner Unit .........................................1125.4. CCD......................................................1145.5. ADF.......................................................1165.6. Cover Assembly....................................1245.7. Right Side Parts....................................1285.8. Motor and Drive Gear Unit....................1325.9. Left Side Parts ......................................1345.10. Rear and Upper Side Parts...................1365.11. Fuser Unit .............................................1385.12. Pickup Roller and

Paper Feed Roller.................................1425.13. Bottom Side Parts.................................1445.14. Mechanical Base ..................................1465.15. Paper Tray ............................................1485.16. 2nd Paper Feed Module .......................1505.17. Paper Tray

(2nd Paper Feed Module).....................1545.18. PC Boards ............................................1565.19. Packing and Accessories......................160

5.20. Printer Controller Module for PCL6 ............................................... 164

5.21. Printer Controller Module for PS/PCL6 ......................................... 166

5.22. 2nd Paper Feed Module Packing and Accessories................................... 168

5.23. Hard Disk Drive Unit............................. 1705.24. Hardware Identification Template ........ 172

Alphanumerical Parts List .................. 174

UF-9000
DP-180/190
1 Specifications Table1.1. Copy Function

Copy Function

Items Description RemarksUF-9000 DP-180 / 190

Basic Specifications1 Type Desktop2 Platen Fixed3 Original Position

Platen Left / Rear / Face DownADF Left / Center / Face UP

4 Recording Paper Path Center5 Drum Organic Photo Conductor (OPC)6 Copy Process Electrostatic Indirect Laser

7 Developing Process Mono Component Non Magnetic Dry Toner

8 Toner Recycle No9 Fusing System Heat & Pressure

10 Max Original Size Letter / A4 / Legal Legal: with ADF only11 Paper Size

Paper TrayLetter / Legal For USA and Canada

A4 / A5 For EUA4 / A5 / B5 For Other Destinations

Bypass

Letter / Legal / Invoice For USA and Canada

A4, FLS, A5 For EUFLS = 8 x 13 in, 8.5 x 13 in

A4 / A5 / B5 / Postcard For Other Destinations12 Media Type

Standard Tray Paper / TransparencyOptional Tray Paper

Bypass Paper / Transparency / Envelope / Label / Thick Paper

13 Warm-up Time 68 °F (20 °C)Power Saver Mode Approx. 15 secSleep ModeShutdown Mode Approx. 18 secPower On

14 First Copy Time Approx. 10 sec

Scan: Platen; Size: Letter / A4; Orientation: Portrait;Paper Feed: 1st Paper Tray; Interval: From Pressing of Start Key to paper exiting to the Exit Tray; When LSU is ready.

8JUN 2004Ver. 2.0

UF-9000
DP-180/190
15 Copy SpeedLetter Approx. 19 cpm Paper Feed: 1st Paper Tray;

Paper Exit: to Exit Tray; Continuous Copy Mode.A4 Approx. 18 cpm

16 ZoomEnlargement Selected Original size / Copy sizeReduction Selected Original size / Copy sizeZoom 50 - 200% 1% Step

17 Paper Feed Front Loading Universal Paper TrayPaper Tray

Capacity 250 sheets x 1 LTR / A4: 20 lb (75 g/m2)

Low Level Paper Warning Yes Orange Low Paper Level Indicator

Bypass

Capacity 1 sheetPaper / Transparency / Envelope / Label / Thick Paper / Postcard etc.

Paper Capacity (Std. Configuration) 250 sheets

18 Multi Copy Range 999 sheets19 Gradation

Text Bi-LevelText / Photo 256 steps Halftone by Error DiffusionPhoto 256 steps

20 Resolution Scanning and Printing.Scan

Mono Max. 600 x 600 dpiColor Max. 300 x 300 dpi

Print (Mono) Max. 1200 (Interpolated) x 600 dpi

Selectable 600 dpi, with Smoothing, the results are similar to PS3 / PCL6 Printers (1200 dpi Interpolated).

21 Scanning typeColor Scan Yes

Color Depth 24 bit (16.7 Million colors)Mono Scan Yes

22 Standard Sorting Memory Size 16 MB

23 Standard Page Memory Size 32 MB24 Exit Tray Capacity 150 sheets LTR / A4: 20 lb (75 g/m2)25 Dimensions

(W x D x H)

18.2 x 19.9 x 20.6 in (462 x 506 x 523 mm)18.2 x 19.9 x 26.1 in

(462 x 506 x 663 mm)With Optional 2nd Paper Feed Module

Copy Function


9JUN 2004Ver. 2.0

UF-9000
DP-180/190
26 Operating Space

(W x D) 18.2 x 21.1 x 31.5 in (462 x 536 x 802 mm)

27 Weight 48.5 lb (22 kg)Options

1 Paper Feed System 550 sheets x 1550 sheets2nd Paper Feed Module Yes

Paper Size Detection Manual Control Panel Selectable

Low Level Paper Warning Yes Orange Low Paper Level Indicator

Max. Paper Capacity 800 sheets LTR / A4: 20 lb (75 g/m2)(Tray 1 + 2)

2 Sorting Image MemoryOptional Image Memory 1 (16 MB) Yes Unit comes standard with

16 MB. 1-Slot available for an Optional Image Memory module.

Optional Image Memory 2 (64 MB) Yes

Optional Image Memory 3 (128 MB) Yes

3 Image MemoryExpansion Flash Memory Card, 4 MB Yes

Image Memory for FacsimileExpansion Flash Memory Card, 8 MB Yes

4 Expansion Board Yes Required for PCL and PS Printing.

5 Hard Disk Drive Yes 40 GB (2.5 inch)6 Handset Yes7 PCL Printer Yes Requires the Optional

Expansion Board.

8 PS / PCL Printer Yes Requires the Optional Expansion Board.

9 Accounting Software Yes For Accounting Function10 Deluxe Stand Yes11 Remote Diagnostic Software Yes12 Mechanical Counter Yes Supplied as a Service Part.

Copy Function


10JUN 2004Ver. 2.0

UF-9000
DP-180/190
Features1 Automatic Features

Auto Magnification Selection NoAuto Paper Selection

Copy NoPrint Yes

Auto Paper Tray Selection Yes

Auto Start Yes Reservation while Power On Initializing

Normal Operation Mode 80 W Turns On the Heater Power.Energy Saver Mode

Power Saver Mode 20 W

Turns Off the Heater Power.Automatically enters the Sleep or Shutdown Mode after 15 minutes from the Standby or Energy Saver Mode.Manually enters the Energy Saver Mode by pressing the Energy Saver key.Sleep or Shutdown mode is controlled by the General Functions setting.

Sleep Mode 12 W (100 VAC PS)15 W (220 VAC PS)

Turns Off the Power of Printer & Scanner.

Shutdown Mode 1.5 W USB / Network Function not available

Transmission (ADF) 45 W (100 VAC PS)56 W (220 VAC PS)

Transmission (Platen) 40 W (100 VAC PS)50 W (220 VAC PS)

Reception / Copy 900 W (100 VAC PS)1000 W (220 VAC PS)

Max 900 W (100 VAC PS)1000 W (220 VAC PS)

Remote Diagnostic YesMachine Stops when Out of Toner Yes

Copy Function


11JUN 2004Ver. 2.0

UF-9000
DP-180/190
2 Additional FeaturesLow Level Paper indicator YesPhoto Mode Yes 256 stepsOriginal Detection Release NoEdit / Effects

Book Mode NoEdge Mode NoMargin Mode NoX-Y Zoom NoInverse Mode (Negative / Positive) No

Centering Mode NoMirror Mode NoImage Repeat No

Others (Inverting ADF & ADU)

2-Page Copy Mode No2 in 1 Yes4 in 1 YesBooklet Mode NoDuplex Copy

1→2 Yes2→1 Yes Scanning twice by turning

original.2→2 YesBook→2 No

Image Rotation (90 or 270 °) NoElectronic Sorting YesRotation Sorting NoInsertion Job NoDepartment Counter Yes 50 DepartmentsADF

Mixed Size Original Feed Yes* LTR and LGL, effective from June 2004 Production

JOB Build and SADF Mode No

Original Counter NoJob Memory No Yes (1 jobs)Job Time Display YesConcurrent Copy NoTandem Copy Mode NoRemote Copy Mode NoScan Once Print Many Mode YesJob Completion Notice Yes For Printer Mode onlyTrial Copy Mode NoWeekly Timer No

Copy Function


12JUN 2004Ver. 2.0

UF-9000
DP-180/190
Function Mode YesInterrupt NoElectronic Counter YesDigital Sky Shot Mode Yes

Check / Slip Mode(Double Exposure) Yes

Check : Dimensions of a Bank check

Slip : Dimensions of a Bank check with a statement

3 Control PanelDisplay LCD 20 digits x 2 lines

Status Lamp YesGREEN : Scanning /

PrintingRED : Alarm / Warning

KeyQWERTY Keyboard YesDirectory Search (4 way) YesOriginal Size YesCopy Size YesKeypad YesClear YesStop YesStart YesEnergy Saver YesSort / Finish NoFunction Mode YesOriginal Detection Release No

Interrupt NoReset YesOne-Touch key Yes

Mode Change Yes Copier / Printer / NW Scanner / Fax and Internet Fax Mode

LCD Main Indication

Message Language (Default)

English (American) For USA and Canada

Specified Language For EU and Other Destinations

Original Size / Image Indication

Yes (without Image)

Paper Size / Image Indication

Yes (without Image)

Paper Tray Selection NoSelected Paper Tray / Tray Status Yes

Original Mode Selection Yes Text / Text-Photo / PhotoCopy Density Selection Yes 5 stepsSetting Confirmation Yes

Copy Function


13JUN 2004Ver. 2.0

UF-9000
DP-180/190
Function Classification YesZoom Magnification YesNumber of Copies YesError Code YesFinishing NoWarning Indicators Yes

No Toner YesNo Paper YesAdd Paper Indication Yes Mechanical IndicatorPaper Jam Indication YesPaper Jam Location YesService Alert Call YesUser Error YesMachine Error YesHistory of Jam Errors Yes

4 Main UnitTotal Counter

Electronic YesMechanical Yes (Optional) Mechanical Counter

Max. Weight of Documents on the Platen Glass 6.61 lb (3 kg)

ADF with Document Guide YesClip Pocket NoOperating Instructions Pocket No

Warning / Caution Label Specified Language5 Optical System

Original Size Detection NoScanning Method 600 dpi CCDDehumidifier No

6 Process System / Yield

Toner Cartridge

Yield: 5 K (5% coverage), 6 K MaxAverage yield is based on 5% coverage of the printable area with repetitive printing of 10 pages (Letter/A4 size, single side printing, default density). The yield of a Toner Cartridge varies depending on the coverage, temperature, humidity, media, etc. Therefore, the average yield cannot be guaranteed. Continuously printing 10% coverage of printable area will reduce the yield of the Toner Cartridge to about half as compared to 5% coverage printing. The maximum yield of the Toner Cartridge will not exceed 6,000 pages by way of Digital Counter.

Copy Function


14JUN 2004Ver. 2.0

UF-9000
DP-180/190
Efficiency1 Productivity

ADF Through-put Speed Approx. 50%ADU Copy Productivity(LTR / A4)

1→2

10 copies More than 50%

Throughput when the LSU is ready; Paper is fed from the 1st Paper Tray and is ejected to the Exit Tray.

PM Cycle1 PM Cycle

Major PM 85 K (Printer), 50K (ADF) Refer to Section 2.4.Minor PM (Cleaning) 10 K (ADF)

2 Average Copy Volume 1.5 K Monthly3 Max. Copy Volume 10 K

Packing Configuration

1 Packing Dimension 24.3 x 29.3 x 26.4 in(616 x 745 x 670 mm)

2 Packing Weight 63.9 lb (29 kg)3 Accessories

Process Unit YesOperating Instructions Yes

Power Supply

1 Power Requirement

99 - 132 VAC 47 - 63 Hz Single phase 120 VAC

180 - 264 VAC 47 - 63 Hz Single phase 220 - 240 VAC

2 Power Consumption Max. 900WAmbient Conditions

1 Temperature 50 - 80 °F / 10 - 30 °C2 Relative Humidity 30 - 80%RH

3 SafetyUL60950-1 / CSA C22.2 No.60950-1 For USA and Canada

EN60950-1 For EU and Other Destinations

4 Energy Saver Energy Star Compliant

5 EMI Class B computing device peripheral in FCC Rules Part 15 For USA and Canada

6 Lead Free Solder (PbF) This Product uses Lead Free (PbF) PCBs

Refer to the inner Front Cover and the Parts Manual for details

Copy Function


15JUN 2004Ver. 2.0

UF-9000
DP-180/190
1.2. Fax, Printer and Internet Fax Functions1.2.1. Fax Function

Fax Function


Main Specifications1 Compatibility Super G3 / G3 ITU-T Std & Non-Std2 PSTN Line Port Yes 1-Line only3 Leased Line Port No4 V.24 Line Port No5 Modem Speed 33.6 - 2.4kbps T.30/V.34/V.17/V.29/V.27ter6 Coding Scheme JBIG/MMR/MR/MH

7 ECM Yes Conforms to ITU-T Rec. T.30 ECM

8 Short Protocol Yes (B, D)

9 Transmission Speed LTR : Approx. 2.7 secA4 : Approx. 2.9 sec

ITU-T Image No. 1 (A4, Std Resolution)

10Communication Resolution dpi x lpi (pels/mm x lines/mm)

Transmission Std. : 203 x 98 (8 x 3.85) Fine : 203 x 196 (8 x 7.7) S-Fine : 203 x 391 (8 x 15.4)

406 x 391 (16 x 15.4) 600dpi : 600 x 600 dpi

Reception Std. : 203 x 98 (8 x 3.85) Fine : 203 x 196 (8 x 7.7) S-Fine : 203 x 391 (8 x 15.4)

406 x 391 (16 x 15.4) 600dpi : 600 x 600 dpi

600 dpi communication is only possible between T.30 Compliant Panafax, WORKiO, and other T.30 compliant machines.

Scanner Mechanism1 Scanning Device CCD (ADF / Platen)

2 Scanning Resolution /SpeedStd: 203 x 98 (8 x 3.85)dpi x lpi (pels/mm x lines/mm)

LTR : 2.7 sec LTR : 2.7 secA4 : 2.9 sec

Excludes: Initializing Time, ADF slipping factor, and Data XMT Time.

(Letter size for USA and Canada; A4 size for Other Destinations)

Fine: 203 x 196 (8 x 7.7)dpi x lpi (pels/mm x lines/mm)S-Fine: 406 x 391 (16 x 15.4) dpi x lpi (pels/mm x lines/mm)600dpi: 600 x 600

3 Document Size (Max.) Legal216 x 2000 mm Using ADF only

4 Effective Scanning Width LTR : 8.3 in (212 mm)A4 : 8.2 in (207 mm)

(Letter size for USA and Canada; A4 size for Other Destinations)

5 ADF Capacity 50 sheets Face Up, top feedLTR / A4 (20 lb / 75 g/m2)

16JUN 2004Ver. 2.0

UF-9000
DP-180/190
6 Collation Stack Yes Face DownPrinter Mechanism

1 Recording Method LP

2 Recording Speed Approx. 19 ppm Recording Speed attained after the 1st copy.

3 Recording Resolution Fax 600 x 600 dpi

4 Recording Paper Size Legal / Letter Legal / LetterA4 / A5 Invoice: Not supported.

5 Effective Printing Width LTR : 8.1 in (207mm)

LTR : 8.1 in (207mm)

A4 : 7.9 in (201 mm)

Letter : USA and CanadaA4 : Other Destinations

6 Recording Paper Capacity 250 sheets Tray 1 + 2 : Max. 800 sheetsLTR / A4: 20 lb (75 g/m2)

7 Collation Stack Yes Face Down

8 Consumable All in One Cartridge

Drum Unit and Toner

Fax Memory

1 Standard Memory 2 MB Flash ROM, ITU-T Image No.1 (A4, Std Resolution)

2 Optional Memory 4 MB8 MB

Expansion Flash Memory Card, using ITU-T Image No.1 (A4, Std Resolution)

Dual Operation1 Multi Task Operation Yes2 Direct XMT Reserve Yes3 Memory XMT Reserve Yes

4 Number of Memory Job Files Yes Max. 50 files

Dialing/Telephone Features1 One-Touch Keys 322 One-Touch / Program Keys 83 One-Touch Auto Dialers 404 Abbr. Auto Dialers 160

5 Total Auto Dialers 200

Plus an additional 800 stations available to select from, when the optional Hard Disk Drive is installed.

6 Directory Search Dialing Yes7 Program Dials 88 Max. Tel Number Digits 36

9 Max. Station Name Characters 15

10 Full Number Dialing (Buffered Dialing) Yes Max. 50 stations

11 Direct Dialing(Monitor Dialing) Yes Voice mode

Fax Function


17JUN 2004Ver. 2.0

UF-9000
DP-180/190
12 Automatic Redialing Yes Up to 15 times at 0 to 15 min. intervals

13 Manual Redialing Yes Pressing the REDIAL/PAUSE button

14 Line Monitor Speaker Yes15 Chain Dialing (Hybrid Dial) Yes In Monitor Dialing mode only16 Pulse / Tone Dialing Yes 10 pps / DTMF17 Pulse to Tone Change No18 Flash Key Yes19 Handset Option

Transmission Features1 Direct Transmission Yes2 Memory Transmission Yes Page Retransmission

3 Quick Memory Transmission Yes

4 Multi-Station Transmission (Sequential Broadcasting) Yes

Max. 250 stations(200 One-Touch / Abbr. + 50 Full Number Dialing)

5 Direct Deferred Transmission No ADF Deferred Transmission

6 Deferred Transmission Yes Max. 50 timers

7 Deferred Multi-Station Transmission Yes

8 Priority Direct Transmission Yes Priority ADF Transmission

9 Priority Memory Transmission No

10 Batch Transmission Yes Real Time (up to 5 Files)

11 90 Degree Rotation Transmission No

12 Cover Sheet Yes13 Confidential Mail Box No14 Multi-Copy Transmission No

15 Memory Back-Up Yes

FAX: Back-up with Flash Memory.

Copy / Printer: No Back-up with D-RAM

16 Duplex Scanning NoReception Features

1 Substitute Reception Yes

2 Fixed Reduction YesLTR/A4/LGL: 70 - 100% (in 1% Steps), Top & Left Alignment

3 Auto Reduction YesLTR/A4/LGL: 70 - 100% (in 1% Steps), Top & Left Alignment

4 Overlap Printing Yes Page End Approx. 0.51 in (13 mm)

5 Receive to Memory Yes

Fax Function


18JUN 2004Ver. 2.0

UF-9000
DP-180/190
6 Distinctive Ring Detector (DRD) Yes Specified Destinations only

7 90 Degree Rotation Reception No

8 Duplex Printing YesPolling

1 Polling Yes2 Turnaround Polling No3 Multi-Station Polling Yes Max. 250 stations4 Deferred Polling Yes Max. 50 timers

5 Deferred Multi-Station Polling Yes Max. 50 timers / 250 stations

6 Direct Polling Tx No7 Memory Polling Tx Yes 1 File8 Preset Polling Password Yes

9 Temporary Polling Password Yes

10 Continuous Polling YesConvenience

1 Panel Display Yes2 Voice Contact No3 Edit File Mode Yes With View Mode4 Incomplete File Save Yes With View Mode5 Automatic Cover Sheet Yes

Certainty1 Verification Stamp Yes2 Header / Total Page Print Yes

3 Transaction Journal Yes 200 Transactions / with View Mode

4 Comm. Journal Yes With Image Data5 Last Ind. XMT Journal Yes

Printout Lists1 One-Touch List Yes2 ABBR. No. List Yes3 Program List Yes4 Address Book Search List Yes Auto Dialer List5 Fax Parameter List Yes6 File List Yes With View Mode7 Ind. XMT Journal Yes8 Directory Sheet Yes

Identifications1 Logo Yes 25 Characters2 Multiple Logo No3 Character ID Yes 16 Characters4 Numeric ID Yes 20 Digits

Fax Function


19JUN 2004Ver. 2.0

UF-9000
DP-180/190
Special Communications1 Password XMT / RCV Yes2 Selective Reception Yes TSI Check3 Relay XMT Request No4 Relay XMT Center No5 Confidential XMT / Polling No6 Confidential Center No7 Mailbox XMT / Polling Yes8 Mailbox Center Yes Max.10 Mail Boxes9 File XMT No

10 Received Fax Forward Yes Received File Transfer 11 Sub-address XMT Yes T. Routing 12 Sub-address Auto Routing Yes13 NYSE Yes For USA and Canada only14 Internet Fax Relay XMT Yes iFAX → iFAX → G3FAX15 Email Relay XMT Yes PC → iFAX → G3FAX16 Panafax Desktop Yes

Standards

1 PSTNFCC Part 68 / Industry Canada

No. CS-03: Issue 8 For USA and Canada

TBR21 For EUOthers

1 Fax Access Code Yes2 PIN Code Access Yes For USA and Canada only3 Intelligent Redial (AI) Yes 5 Files4 Department Code Yes 50 Departmental Codes5 Power Saver Mode Yes6 Self Diagnostic Function Yes

7 Remote Diagnostic Function Yes Specific Destinations only

8 Check & Call Function Yes9 V.24 / Encryption Interface No

Fax Function


20JUN 2004Ver. 2.0

UF-9000
DP-180/190
1.2.2. Printer Function

Printer Function


Interface1 Centronics Parallel I/F No

2 LAN (Network) Yes Ethernet 10Base-T/100Base-TX

3 USB Port Yes USB1.14 IEEE-1394 No Firewire

Printer Function1 Printing Size LGL / LTR LGL / LTR /

A4 / A5 / B52 Bypass Yes3 Stapling No

4 Printing Resolution (dpi) Max. 1200 (Interpolated) x 600 dpi

Selectable 600 dpi, with Smoothing, the results are similar to PS3 / PCL6 Printers (1200 dpi Interpolated).

5 Interface USB / Ethernet

6 OS Win 98 / Win Me / Win NT 4.0 / Win 2000 / Win XP / MAC 8.6-10.1 MAC 8.6-10.1 is PS only.

7 Printer Work Memory Size 20 MB Not expandable8 GDI Yes

9 PDL (PCL6) YesRequires Optional PS / PCL6 Emulation Kit and Optional Expansion Board.

10 PDL (PS3) YesRequires Optional PS / PCL6 Emulation Kit and Optional Expansion Board.

11 Duplex Printing Yes Custom Size/Postcard Size is not available.

12 Collation Stack Yes13 Status Monitor

Network YesUSB No

14 Network Status Monitor Yes15 Smoothing Yes16 Applicable PC IBM PC, AT or Compatible, MAC MAC is PS only.17 Multi-Task Operation

Printing while Fax-XMT from Memory Yes

Printing while Fax-RCV into Memory Yes

Fax-XMT from Memory while Printing Yes

Fax-RCV into Memory while Printing Yes

21JUN 2004Ver. 2.0

UF-9000
DP-180/190
18 Output to separate tray for Printing, Fax, Copy No

19 Font Yes Requires Optional PCL6 or PS / PCL6 Emulation Kit

20 Mailbox Yes

Requires Optional HDD Unit.Max. 100 Users.Max. 20 mailboxes for each User ID

21 Secure Mailbox Yes

Requires Optional HDD Unit.Max. 100 Users.Max. 20 mailboxes for eachUser ID

Printer Function


22JUN 2004Ver. 2.0

UF-9000
DP-180/190
1.2.3. Network Scanner Function

Network Scanner Function

Items Description RemarksUF-9000 / DP-180/190

Interface1 Centronics Parallel I/F No2 LAN (Network) Yes Ethernet 10Base-T/100Base-TX3 USB Port No4 IEEE-1394 No Firewire

Network Scanning Function1 Scanning Device CCD (ADF / Platen)2 Scanning Speed (ADF)

Mono LTR: 2.7 secA4 : 2.9 sec

600 dpi(Data XMT time is not included.)

Color LTR: 11 secA4 : 12 sec

300 dpi(Data XMT time is not included.)

3 Halftone 256 Halftone shades, Color 24bit, 16670 K With Error Diffusion

4 Max. Document Size Legal216 x 2000 mm Using ADF only

5 Scanning Resolution(dpi)

Mono600 x 600300 x 300150 x 150

Default: 300 dpi

Color300 x 300150 x 15075 x 75

Default: 150 dpi

6 OS Win 98 / Me / Win NT 4.0 / Win 2000 / XP

7 2-Sided Scanning No8 File Format

Mono Multi-page TIFF / PDFColor JPEG / PDF

9 Completion Notice Yes Auto Pop-up on the PC Screen 10 Protocol TCP/IP / Non-Std

Network Address Features

1 One Touch Address Keys 40 Shared with Fax/I-Fax One-Touch Address, 40 in Total

2 Abbr. Address Numbers 60 Independent for Network Scanner

23JUN 2004Ver. 2.0

UF-9000
DP-180/190
1.2.4. Internet Fax Function

Internet Fax Function


Main Specifications1 Communication Protocols SMTP / POP3 / MIME2 Max. Modem Speed NA3 Coding Scheme JBIG/MMR/MR/MH

4 File Format TIFF / JPEG or PDF

Selectable(PDF & JPEG formats are used for Scan-to-Email, current I-Fax standards do not support these file formats)

5 Line Interface RJ-45 Ethernet LANScanner Mechanism

1 Max. Document Size Legal216 x 2000 mm With the ADF only

2 Effective Scanning Width LTR : 8.3 in (212 mm)A4 : 8.2 in (207 mm)

Letter size: for USA and CanadaA4 size : for Other Destinations

3 Scanning Resolutiondpi x lpi (pel/mm x lines/mm)

Std : 203 x 98 (8 x 3.85)Fine : 203 x 196 (8 x 7.7)S-Fine : 203 x 391 (8 x 15.4)

: 406 x 391 (16 x 15.4)600dpi : 600 x 600 dpi

LAN: 600 dpi, 16 x 15.4 Scanning Resolution is available.

Printer Mechanism1 Printing Resolution 600 dpi

2 Effective Recording Width LTR : 8.1 in (207 mm)A4 : 7.9 in (201 mm)

Transmission Features

1 Multi-Task Operation Yes Convenient simultaneous G3 Fax and LAN operation.

2 Memory Transmission Yes

3 Sequential Multi-Station Transmission Yes

4 Simultaneous Multi-Station Transmission Yes

Max. 250 stations(200 One-Touch / Abbr. + 50 Full Number Dialing)

5 Sender Selection Yes

6 G3 / Email Mixed Broadcasting Yes

7 Deferred Transmission Yes8 Fax Forward Yes Received File Transfer9 Sub-address RCV Yes Inbound Routing

10 Mail Header Email Header Print Selection Yes All or From / To / Subject onlySubject Line Random Entry

24JUN 2004Ver. 2.0

UF-9000
DP-180/190
LAN Features1 Internet Fax Communication Yes2 Internet Mail Reception Yes3 Internet Fax Server Features

Internet Fax Relay XMT Yes iFAX → iFAX → G3FAXEmail Relay XMT Yes PC → iFAX → G3FAXReceived Fax / Email Forward Yes Local print available

PC FAX Transmission Yes Panafax Desktop Only (Network)

Inbound Routing Yes Using Sub-Address. Local print available

Phone Book Registration from PC Yes Via Email or Network Address Editor

4 I-Fax Parameters Registration via Email Yes

5 Internet Delivery Confirmation Yes With MDN 6 Network Scanning Yes 600 dpi7 Network Printing

LPR / LPD Yes 600 dpiGDI Yes 600 dpi

PDL YesRequires Optional PS / PCL6 Emulation Kit and Optional Expansion Board.

8 DHCP Client Yes9 LDAP Yes Lightweight Directory Access Protocol

10 TIFF Viewer Yes Selectable, PDMS / TIFF Viewer11 NYSE Yes For USA and Canada only

Certainty1 Comm. Journal (w / Image) Yes

ID1 Email Address Yes

Internet Fax Function


25JUN 2004Ver. 2.0

UF-9000
DP-180/190
1.3. System Combination

Scanner Unit (SPC PC Board)

Expansion FlashMemory Card

4 or 8MB

Main PC Board

Image Memory

(1-Slot)

Electronic Sorting Memory

2nd Paper Feed Module Option

Option

Standard Configuration

Panel(PNL PC Board)

MechanicalCounter Option

Handset KitOption

16, 64 or 128MB

Hard DiskDrive Option

Accounting Software Option

PCL6 Emulation Option

PS/PCL6 Emulation Option

USBInterface

GDI Printer

10/100 EthernetInterface

Super G3 Fax Communication

Automatic Document Feeder (ADF)

Automatic Duplex Unit

Internet Fax/E-Mail

NetworkScanner

Program Expansion Board

8MB

26JUN 2004Ver. 2.0

UF-9000
DP-180/190
1.4. Options List■ Options

■ Supplies

UF-9000

DP-180/190

Note:PCL6 is a Page Description Language of the Hewlett-Packard Company.PostScript 3 (PS3) is a Page Description Language of the Adobe Systems Company.The Part Name(s) / Part Number(s) differ depending on the Models and the Destinations.

Option Name Option Number Remarks

Printer Controller Module (PCL6*) DA-PC188 For DP-180/190DA-PC190 For UF-9000

Multi Page Description Language Controller Module (PCL6/PostScript 3*)

DA-MC188 For DP-180/190DA-MC190 For UF-9000

Hard Disk Drive Unit DA-HD19

Additional Optional Sorting Image Memory (Minimum 16 MB) is required for the Hard Disk Drive to function. (PS additional fonts, Mail Box, additional 800 addresses, etc.)

Expansion Board DA-EM600 F-ROM Board (8 MB) is required for PCL or PS printing.

Expansion Flash Memory Card, 4 MB UE-410047 Additional Memory for Fax / I-FaxExpansion Flash Memory Card, 8 MB UE-410048Image Memory (16 MB) DA-SM16B

For Electronic SortingImage Memory (64 MB) DA-SM64BImage Memory (128 MB) DA-SM28BAccounting Software DA-WA10 For Accounting Function2nd Paper Feed Module DA-DS188

Handset KitUE-403171 For USA and Canada

UE-403172 For Other DestinationsAvailable in Specified Destinations

Deluxe Stand DA1D190 For USA and Canada onlyMechanical Counter DZTQ000066 Supplied as a Service Part.

Part Name Part Number RemarksToner Cartridge UG-5530 All in One Cartridge

Part Name Part Number Remarks

Toner DQ-UG16H For DP-180DQ-UG17H For DP-190

Drum Unit DQ-UH34H For DP-180DQ-UH35H For DP-190

27JUN 2004Ver. 2.0

UF-9000
DP-180/190
2 Maintenance, Adjustments and Check Points2.1. Preventive Maintenance

Preventive maintenance is performed at specific intervals and consists of machine

cleaning and parts replacement.

It is essential to perform these service activities properly and at the specified intervals

for customer satisfaction.

The purpose of this service is to maintain machine performance and image quality.

- You should prepare the replacement parts, and cleaning tools beforehand.

- After completing the preventive maintenance, discard the used parts andpackaging in accordance with local regulations and clean the surrounding area.

- Before servicing the equipment, disconnect the power cord from the wall outlet.- Before using solvents such as IPA (Isopropyl alcohol), put on rubber gloves

and eye protection.

1 Timing- Perform the preventive maintenance in accordance with the Preventive

Maintenance Check List. (refer to 2.4.)

2 Cleaning the Rollers- Rollers should be cleaned with water and cloth.- Use the IPA (Isopropyl Alcohol) sparingly.

3 Disassembly and Adjustment Precautions

Turn the Power Switch on the Left Side of the machine to the OFFposition, and then unplug the AC Power Cord from the wall outlet before disassembling the machine. (During a Lightning Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord.)

CAUTION!

- After taking the unit apart, do not attempt to operate the machine.- When operating the machine with covers removed, be careful and avoid clothing

from being caught by moving components.

-

- Ensure to use correct screws.

- Use toothed lock washers for the installation of ground wires to ensure electrical

continuity.

- To reassemble, reverse the sequence of disassembly, unless otherwise specified.

- Blown fuses should only be replaced with fuses of the same specified rating.

While the electricity is applied to the unit, do not connect nor disconnect theconnectors on any PC Board.

28JUN 2004Ver. 2.0

UF-9000
DP-180/190
4 Laser Handling Precautions

The optical laser system employed by this photocopier is completely sealed by

a protective housing and an external cover. Therefore, the laser beam will not

stray or leak during photocopying operation.

However, when servicing the photocopier, take the following precautions:

1. Do not insert any screwdrivers or other tools that have high reflective

properties into the laser's path..2. Before servicing the photocopier, remove watches, rings, or other metallic

objects that you may be wearing. (This is to avoid the danger of the laser

striking the eye by reflecting off the metallic objects being worn.)

Since the laser beam cannot be seen with the naked eye, for maximum

safety, please follow the above precautions.

5 Safety Interlock Switches

- The service technician may defeat the safety interlock switches by inserting a

interlock cheater into the opening of the switch cover.

- Ensure to remove the interlock cheater from the switch cover after completion

of service.

29JUN 2004Ver. 2.0

UF-9000
DP-180/190
2.2. Required Tools

2.2.1. Preventive Maintenance Method

No. Tools No. Tools1 Soft Cloth 7 Pliers2 Isopropyl Alcohol 8 Cotton Swab3 Phillips Screwdriver (#2) 9 Brush

4 Stubby Phillips Screwdriver (#2) 10KS-660 - Conductive Grease(Available from Shin-Etsu Silicones of America, Inc. URL: http://www.shinetsusilicones.com)

5 Slotted Screwdriver (3/32 in) 11Molykote EM-50L Grease (Available from Dow Corning, URL: http://www.dowcorning.com)

6 Tweezer

No. Part Description Important Action Comments

1 Memory Data Check 1. Print the RAM DATA for reference and as a precaution.2. After completing the task(s), print and compare the RAM

DATA with the previously printed one.2 Auto Document

Feeder (ADF)Check & Clean

1. Clean the Rollers and Separation Rubber with Wet soft cloth (Water).Note:

For stubborn toner accumulation, wipe with a soft cloth saturated with Isopropyl Alcohol first, then follow up with a soft cloth saturated with water.

3 Scanner Unit Check & Clean

1. Clean the Scanning Glass or White Reference Sheet with Isopropyl Alcohol when required.

4 Transmitter Unit Check & Clean

1. Remove any foreign obstacles.2. Clean the Rollers with Wet soft cloth (Water).

5 Mirrors Check & Clean

1. Do not touch the surface of the Mirrors with your bare hands. Clean any dirt or fingerprints with a soft cloth, saturated with Isopropyl Alcohol.

6 Inspection Items Check 1. Check the Harnesses.2. Check the Connectors.3. Check the Screws. If required, replace consumable parts.

7 Gears, Rollers Shafts Check & Grease

1. Check and grease the required Gears and Shafts.

8 Timing Belts Check & Clean

1. Check for belt looseness or abrasion.2. Adjust the Idle Pulley.

30JUN 2004Ver. 2.0

UF-9000
DP-180/190
2.3. Preventive Maintenance Points

31JUN 2004Ver. 2.0

UF-9000
DP-180/190
2.4. Preventive Maintenance Check ListThe chart outlined below is a general guideline for maintenance. The list is for an average usage of 50 transmitted and received documents per day. Needless to say, the environmental conditions and actual use will vary these factors. The chart below is for reference only.

Note:1. Wet Cloth represents a soft cloth saturated with water. For stubborn toner accumulation, wipe with a

soft cloth saturated with Isopropyl Alcohol first, then follow up with a soft cloth saturated with water.2. The Maintenance Cycle is based on the Counter Information for each individual module.

To verify the counter information, print the Total Counter List using the Service Mode: F7 - Electronic Counter - 00 (List Print).

3. Cleaning, Replacement and Adjustment Cycle (Sheet) are based on using Panasonic's recommended standard paper and supplies. These cycles may vary with the kind of paper used, Paper size, orientation, print duty, continuous/interval print and/or ambient conditions.

• Total Counter View Mode on the LCDThe Total Counter can be displayed on the Panel Display by pressing "COPY SIZE" and "PAPER TRAY" keys simultaneously in Standby mode for quick reference.

• LCD Contrast AdjustmentPress holding the “CLEAR” key and press “ORIGINAL SIZE” key for Lighter or “COPY SIZE” key for Darker.

No.Preventive

Maintenance Parts

Ref. No.

Cleaning Replacement/Adjustment Ref. CounterCycle

(Sheet) Method Cycle (Sheet) Procedure

ADF Unit1 Separation Rubber 547 10K Wet soft cloth 50K Refer to

2.2.1. of the Service Manual

F7-082 Pickup Roller 414 10K Wet soft cloth 100K3 ADF Roller 417 10K Wet soft cloth 100K4 Feed Roller 516 10K Wet soft cloth 100K

Paper Feed Module5 Pickup Roller 1316 10K Wet soft cloth 85K Refer to

2.2.9. of the Service Manual F7-12

6 Separator Pad 1615 10K Wet soft cloth 85K

7 Bias Transfer Roller (BTR) 1503 10K Dry soft cloth 85K

Refer to 2.2.10. of the Service Manual

2nd Paper Feed Module8 Pickup Roller 1733 10K Wet soft cloth 85K Refer to

2.2.12. of the Service Manual

F7-139 Separator Pad 1812 10K Wet soft cloth 85K

Fuser Unit

10 Fuser Unit 1117 - - 85K

Refer to 2.2.8. of the Service Manual

F7-02

TOTAL COUNTER

1234

32JUN 2004Ver. 2.0

UF-9000
DP-180/190
2.5. Updating the FirmwareThe Quickest and Most Easiest Method of Updating the Firmware is to use the Network Firmware Program Tool (FUP) using Ethernet LAN Port and a Crossover Cable.The Network FUP Tool version must be 3.XX or higher, and it can be found on the Panasonic Document Management System CD-ROM included with the main unit or on the CD-ROM included with the PCL or PS/PCL options.Refer to the Firmware Update Operation Instructions, Service Notes (Section 8.1. of the Service Manual) for additional details.

2.5.1. Firmware ConfigurationA. Hardware Configuration

This machine is controlled by two (2) CPUs which are located on the System Control (SC) PC Board and the Scanner Control (Scanner).

B. SC PC Board FirmwareThe 4 MB Program Memory (F-ROM) is integrated on the SC PCB. An Optional Expansion 8 MB Program Memory (FRM8 PCB) can be installed into SLOT 1.The Firmware to be written into the 4 MB onboard and the 8 MB of SLOT 1 depends upon the configuration of the Standard, PCL or PS Options.

(1) StandardThe Standard Program (1) is only written into the 4 MB onboard, which is assigned as ROM Code (A).

(2) For PCL OptionThe PCL Control Program (2) must be written into the 4 MB onboard, which is assigned as ROM Code (B). The PCL Control Program (3) and PCL Font data (4) are written into the 8 MB in the SLOT 1. The Firmware (3) and (4) are assigned as ROM Code (C).When using 8 MB Flash Memory Card, the 8 MB Program (C) can be written onto one card.When using 4 MB Flash Memory Card, the 8 MB program (C) must be divided onto 2 cards, one 4 MB card for the PCL Control Program (3) and one 4 MB card for the PCL Font data (4).

(3) For PS OptionThe PS Control Program must be written into the 4 MB onboard, which is assigned as ROM Code (D). The PS Control Program (6) and (7) are written into the 8 MB in the SLOT 1. Both Firmwares (6) and (7) are assigned as ROM Code (E). When using 4 MB Flash Memory Card, the 8 MB program (E) must be divided onto 2 cards, one 4

SC PC Board StandardConfiguration

With PCL OptionConfiguration

With PS OptionConfiguration

On Board (A)

4 MB

(B)

4 MB

(D)

4 MB

PC (1) (2) (5)

CPU 4 MBProgram Program Program

Ethernet Port

F-ROM

PC

USB Port Slot 1 (CN327) (C) 8MB (E) 8MB(3) (6)

Program Program

8 MB

2 MB (a) 4 MB (a)FRM8 PCB

(4) (7)Flash Memory Card

Font

4 MB or 8 MB4 MB (b)

4 MB(b)

Panel Control Program (Display & Key In)Bitmap DataFont Data

SPC PC Board

CPU 2 MB

Scanner Control ProgramF-ROM

Font

33JUN 2004Ver. 2.0

UF-9000
DP-180/190
MB card for the PS Control Program (6) and one 4 MB card for the PS Control Program (7).

C. SPC PC Board FirmwareThe 2 MB Program Memory (F-ROM) is integrated on the SPC PCB. The Programs for Scanner Control and Printer Control are saved on the Board. The Firmware is transferred as Serial Data from the SC PCB.

D. Firmware Updating PortsThree (3) types of Ports are available for updating the firmware.

(1) Ethernet LAN Port (The Quickest and Most Easiest Method)The machine's Firmware can be updated from a PC via Local Area Network (LAN). Refer to the Firmware Update Operation Instructions, Service Notes (Section 8.1. of the Service Manual) for additional details.

(2) USB Port (Alternate)The machine's Firmware can be updated from a PC via USB Port. The Master Firmware Card can also be created from a PC using the USB Port. Refer to the Firmware Update Operation Instructions, Service Notes (Section 8.1. of the Service Manual) for additional details.

(3) Flash Memory Card (Alternate)The machine's Firmware can be updated using the Master Firmware Card. The Master Firmware Card can be created by copying the Firmware from an existing machine's SC PCB using a 4 MB or 8 MB Flash Memory Card. To update the SC, SPC and PNL PCB, 3 Flash Memory Cards are required for the Standard configuration or 5 Flash Memory Cards for the PCL or PS/PCL configuration.

34JUN 2004Ver. 2.0

UF-9000
DP-180/190
2.5.2. Updating through a LAN Port (The Quickest and Most Easiest Method)The firmware code can be easily updated when the main unit is connected to a LAN. The Network Firmware Update Tool can also be used by connecting to the machine using a crossover cable, if the unit is not connected to a LAN.

1) Install the Network Firmware Update Tool to your PCThe option CD-ROM includes the Network Firmware Update Tool and the Main Unit Firmware Code. Please refer to the following Operating Instructions to install the Network Firmware Update Tool. The installation password is "workio".Operating Instructions:\xFirmware\Tools\NwFirmup\NwFirmup OI.pdf (Refer to the NW Firmware Update Tool OI on the CD)Setup:\xFirmware\Tools\NwFirmup\Setup\Setup.exe

2) Preparing the Firmware CodeDouble click the appropriate Destination Shortcut Batch File and copy the Firmware Code File on the CD-ROM to the Firmware Data Folder in your PC. Note that the files in the Archive will be extracted automatically into the designated folder when the Archived file (.exe) is Double-clicked.Example:From:Destination Shortcut Batch File: D:(CD-ROM Drive) \ xFirmware \ USA.batFirmware Code File: UF-9000_AU_xxxxxxxx.exe or DP-190_180_xx_xxxxxxxx.exeTo:Firmware Data Folder: C:\ Panasonic \ Panasonic-FUP \ Data

3) Preparing the Main Unit for the Firmware UpgradeMake sure the unit's Key Operator Password is the same as the tool's password.Make sure the unit is in an idle state (e.g. not making copies, not printing, etc.).

4) Upgrading the Main Unit's Firmware CodeStart the Network Firmware Update Tool and select the following Firmware Code Folders in the C:\Program Files\Panasonic\Panasonic-FUP\Data folder, and then follow the display instructions to upgrade the Main Unit's Firmware Codes.

Parent Firmware File Folder Sub Firmware File Folder Transferring Order\ UF-9000_AU_xxxxxxxx \ SC_STD \ DX-TriAxVxxxxx_xx 1

\ SC_PCL \ DX-TriBxVxxxxx_xx 1\ SC_PS \ DX-TriDxVxxxxx_xx 1\ SPC \ DX-TRI-SAAVxxxxx 2

\ DP-190_180_xx_xxxxxxxx \ SC_STD \ DP-TriAxVxxxxx_xx 1\ SC_PCL \ DP-TriBxVxxxxx_xx 1\ SC_PS \ DP-TriDxVxxxxx_xx 1\ SPC \ DX-Tri-SAAVxxxxx 2

When you select the Parent Folder, the following Firmware Type window appears. Proper Sub File Folders are selected automatically by selecting the Firmware Type.The transferring order is set up automatically.

35JUN 2004Ver. 2.0

UF-9000
DP-180/190
Note:1. Manual mode must be used, when updating the designated version of the firmware or changing

the type of the firmware. Please refer to the Section 2.2, "Setting up the Network Firmware Update Tool, File Selection Tab" of the Operating Instructions.

2. While updating the firmware code, the display may become garbled, however, it will return to normal upon completion of the firmware update.

3. If the firmware update fails and the unit does not boot up, the Network Firmware Update Tool will not be able to transfer the firmware code. If this occurs, please refer to the next section "Updating through the USB Port" and use the Local Firmware Update Tool to recover the unit.

4. The suffix "_xx" for the Folder Name or File Name may not exist depending on the destination location.

2.5.3. Updating through USB Port (Alternate Method)If the device is not connected to the LAN, upgrade the firmware code using the USB Port.

1) Install the Local Firmware Update Tool to your PCThe option CD-ROM includes the Local Firmware Update Tool and the Main Unit Firmware Code. Please refer to the following Operating Instructions to install the Local Firmware Update Tool.Operating Instructions:\xFirmware\Tools\Firmup\FIRMUP OI.pdf (Refer to the Local Firmware Update Tool OI on the CD)Setup:\xFirmware\Tools\Firmup\Setup\Setup.exe

2) Preparing the Firmware CodeDouble click the appropriate Destination Shortcut Batch File and copy the Firmware Code File on the CD-ROM to the Firmware Data Folder in your PC. Note that the files in the Archive will be extracted automatically into the designated folder when the Archived file (.exe) is Double-clicked.Example:From:Destination Shortcut Batch File: D:(CD-ROM Drive) \ xFirmware \ USA.batFirmware Code File: UF-9000_AU_xxxxxxxx.exe or DP-190_180_xx_xxxxxxxx.exeTo:Firmware Data Folder: C:\ Panasonic \ Panasonic-FUP \ Data

3) Preparing the Main Unit for the Firmware UpgradeImportant: DO NOT connect the USB Cable yet.Enter into Test Mode F9-07-01 to enable the unit to accept the programming code from the USB Port.

Now connect the USB Cable between the Unit and PC.Repeat the above steps if there are additional firmware code files to be updated.

36JUN 2004Ver. 2.0

UF-9000
DP-180/190
4) Upgrading the Main Unit's Firmware CodeStart the Local Firmware Update Tool and select the following Firmware Code Parent File Folder in the C:\Panasonic\Panasonic-FUP\Data folder, and select the Firmware Code Type then follow the display instructions to upgrade the Main Unit's Firmware Codes. You must process each firmware file separately in this manner and sequence.

Note:1. While updating the firmware code, the display may become garbled, however, it will return to

normal upon completion of the firmware update.2. Please refer to the service manual for additional details.3. The suffix "_xx" for the Folder Name or File Name may not exist depending on the destination

location.

2.5.4. Updating the Firmware using the Master Firmware Card (Alternate Method)1. Before starting, print the F5/F6 Parameters List (Copy Service Mode F9-03-00).2. Turn the Power Switch on the left side of the machine to the OFF position. (During a Lightning

Storm, to prevent electrocution disconnect the Telephone Line Cable first before unplugging the AC Power Cord.)

3. Install the appropriate Master Firmware Card into the machine.4. Turn the Power Switch on the Left Side of the machine to the ON position.5. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.6. Perform the Copy Service Mode F9-07-00 (Update From Master Card).7. The firmware is copied into the machine.8. After the update is completed, the machine reboots itself and returns to standby.9. Turn the Power Switch on the left side of the machine to the OFF position.

10. Remove the Master Firmware Card from the machine.11. Turn the Power Switch on the Left Side of the machine to the ON position.

Parent Firmware File Folder Sub Firmware File Folder Firmware File Transferring Order

\ UF-9000_AU_xxxxxxxx \ SC_STD \ DX-TriAxVxxxxx_xx DX-TriAxVxxxxx_xx.bin 1\ SC_PCL \ DX-TriBxVxxxxx_xx DX-TriBxVxxxxx_xx.bin

DX-TriCxVxxxxxa_xx.binDX-TriCxVxxxxxb.bin

1-11-21-3

\ SC_PS \ DX-TriDxVxxxxx_xx DX-TriDxVxxxxx_xx.binDX-TriExVxxxxxa_xx.binDX-TriExVxxxxxb.bin

1-11-21-3

\ SPC \ DX-TRI-SAAVxxxxx DX-TRI-SAAVxxxxx.bin 2\ DP-190_180_xx_xxxxxxxx \ SC_STD \ DP-TriAxVxxxxx_xx DP-TriAxVxxxxx_xx.bin 1

\ SC_PCL \ DP-TriBxVxxxxx_xx DP-TriBxVxxxxx_xx.binDP-TriCxVxxxxxa_xx.binDP-TriCxVxxxxxb.bin

1-11-21-3

\ SC_PS \ DP-TriDxVxxxxx_xx DP-TriDxVxxxxx_xx.binDP-TriExVxxxxxa_xx.binDP-TriExVxxxxxb.bin

1-11-21-3

\ SPC \ DX-Tri-SAAVxxxxx DX-TRI-SAAVxxxxx.bin 2

When you select the Parent Folder, the following Firmware Type window appears. Proper Firmware Files are selected automatically by selecting the Firmware Type.The transferring order is set up automatically.

37JUN 2004Ver. 2.0

UF-9000
DP-180/190
12. Reprogram the F5 & F6 Parameters according to the lists printed in Step 1 above if the settings are other than factory default.

Note:After the update is completed, the machine reboots itself and returns to standby mode.Repeat the above steps if there are additional firmware code files to be updated.Confirm that the update was successfully completed by checking the Firmware Version with F9 Parameters F9-02-xx.

Caution:If the unit does not boot up properly in step 8, refer to 2.5.8. (Firmware Emergency Recovery)

2.5.5. Creating a Master Firmware CardA. Utilizing the Firmware Update Kit

1) Install the Local Firmware Update Tool to your PCThe option CD-ROM includes the Local Firmware Update Tool and the Main Unit Firmware Code. Please refer to the following Operating Instructions to install the Local Firmware Update Tool.

Operating Instructions:\xFirmware\Tools\Firmup\FIRMUP OI.pdf (Refer to the Local Firmware Update Tool OI on the CD)Setup:\xFirmware\Tools\Firmup\Setup\Setup.exe

2) Preparing the Firmware CodeDouble click the appropriate Destination Shortcut Batch File and copy the Firmware Code File on the CD-ROM to the Firmware Data Folder in your PC. Note that the files in the Archive will be extracted automatically into the designated folder when the Archived file (.exe) is Double-clicked.Example:From:Destination Shortcut Batch File: D:(CD-ROM Drive) \ xFirmware \ USA.batFirmware Code File: UF-9000_AU_xxxxxxxx.exe or DP-190_180_xx_xxxxxxxx.exe

To:Firmware Data Folder: C:\ Panasonic \ Panasonic-FUP \ Data

3) Preparing the Main Unit for the Programming Master Firmware CardImportant: DO NOT connect the USB Cable yet.1. Turn the Power Switch on the left side of the machine to the OFF position. (During a Lightning


2. Insert/Remove the Flash Memory Card (4 MB or 8 MB) into/from the machine.3. Turn the Power Switch on the Left Side of the machine to the ON position.4. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.5. Perform the Update Program Card Mode F9-09 (Update Program Card).

The unit is now ready to accept the firmware code from the USB Port.Now connect the USB Cable between the Unit and PC. (Refer to the Local Firmware Update Tool OI on the CD)

Repeat the above steps if there are additional master firmware cards to be programmed.

38JUN 2004Ver. 2.0

UF-9000
DP-180/190
B. Copying the Firmware from an Existing Machine using a Flash Memory Card (4 MB or 8 MB)1. Turn the Power Switch on the left side of the machine to the OFF position. (During a Lightning


2. Install a Flash Memory Card (4 MB or 8 MB) into the machine.3. Turn the Power Switch on the Left Side of the machine to the ON position.4. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.5. Perform the Copy Service Mode F9-08 (Program Backup).6. The firmware is copied into the Flash Memory Card.7. After the backup is completed, press "STOP" first and then press "FUNCTION" + "CLEAR" keys

simultaneously to return to standby.8. Turn the Power Switch on the left side of the machine to the OFF position.9. Remove the Master Firmware Card that you just created from the machine.

10. Turn the Power Switch on the Left Side of the machine to the ON position.11. Use this Master Firmware Card to update the firmware on other machines.

2.5.6. Erasing the Master Firmware Card1. Turn the Power Switch on the left side of the machine to the OFF position. (During a Lightning


2. Install the Master Firmware Card into the machine.3. Turn the Power Switch on the Left Side of the machine to the ON position.4. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.5. Perform the Service Mode F9-09 (Update Program Card).6. After the Flash Memory Card is erased, machine prompts “READY TO PROGRAM PRESS SET TO

START”. Press “STOP”.7. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to

standby.8. Turn the Power Switch on the left side of the machine to the OFF position.9. Remove the blank Flash Memory Card from the machine.

10. Repeat from Step 2 above if you are erasing another Master Firmware Card.

2.5.7. Notice after installing the HDD optionAfter the Hard Disk Drive Unit is installed, to prevent a Scan Disk Function from being performed (similar to Windows OS when the power is abruptly interrupted), it is important to follow the step sequence below when turning OFF the Power Switch on the machine.

1. If the machine is in the "ENERGY SAVER (Shutdown Mode)", you may turn the Power Switch on the Left Side of the machine to the OFF position. If it is not in the "ENERGY SAVER (Shutdown Mode)", continue to step 2 below.

2. Press "FUNCTION" and "ENERGY SAVER" keys simultaneously first.3. Wait approximately 10 seconds while the machine writes the closing status onto the Hard Disk Drive

Unit and advances into “ENERGY SAVER MODE”.4. Turn the Power Switch on the Left Side of the machine to the OFF position.5. Unplug the AC Power Cord. (During a Lightning Storm, to prevent electrocution disconnect the

Telephone Line Cable first before unplugging the AC Power Cord.)6. After finishing the installation of the Hard Disk Drive, please go over the above Power Down

procedure with the customer to avoid the Scan Disk Function from being performed (indicated by SCANNING HARD DISK message on the display), and customer inquiries related to abrupt Power Off.

7. Reconnect the Telephone Line Cable if it was disconnected.

39JUN 2004Ver. 2.0

UF-9000
DP-180/190
2.5.8. Firmware Emergency RecoveryThe easiest method to recover the firmware in an Emergency Recovery routine is to use the Master Firmware Flash Card method (1 Flash Card required).

Whichever method you select, it is easier to restore the machine's firmware to the Standard (AAV) Type first as it only requires 1 file (SC) to bring the machine to initial working condition. Note:

It is not possible to recover the SPC using this method.

After recovering, if optional PCL or PS/PCL firmware is required, use the Network Firmware Update Tool or the Local Firmware Update Tool to update the firmware to the required level.

If the unit does not boot up properly, follow the steps below:1. Turn the power Off.

Before proceeding to the next step, you must create the Master Firmware Flash Cards (read the appropriate sections first 3.5.5).

2. Turn the power On while holding the [ENERGY SAVER] button.3. When the green lamp on the front panel turns On, release the [ENERGY SAVER] button.

The unit is now ready to accept the firmware code from Master Firmware Card.Repeat the above steps if there are additional firmware code files to be updated.

2.5.9. Firmware Version

SC :DP-TRI A A Vxxxxx AU

Destination Code (Copier) PU : USA/Canada PB : UK

Destination Code (Fax) AU : USA/Canada AB : UK

Firmware Version (V1xxxx)Language Code A : A-English, C-French & Spanish B : A-English, Spanish & Portuguese

Firmware Type A : Standard B, C, D, E : Optional

Model Number

etc.

(a)DX-TRI A A Vxxxxx (a) AU

b : English, French & Spanishg : German, French & Italian

Division Soft (When it is divided into (a) and (b))

40JUN 2004Ver. 2.0

UF-9000
DP-180/190
SPC : DX-TRI S A A Vxxxxx

Firmware Version (V1xxxx)

AA: Fixed

SPC

Model Number

41JUN 2004Ver. 2.0

UF-9000
DP-180/190
2.6. Adjusting the Printer Registration, LSU Image Side to SideWhen installing the Paper Tray option, the following LSU Image Side to Side adjustment may be required.The Printer registration is adjusted at the factory. If copy image is abnormal, especially in the Rotation Copy mode, adjust it by the following procedure.

2.6.1. Printer Registration 1. Insert Letter or A4 size paper into the 1st tray and change the tray setting to the appropriate paper

size. Empty all the remaining trays (including the bypass tray) to disable them.2. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.3. Perform the Service Mode F1-03 (Print Test Pattern 1).4. Check the gap of the print pattern from the paper edge, refer to the Figure below.5. Perform the Service Mode F6-04 (Printer Registration) to adjust the gap to be 5 mm.6. If the gap is less than 5 mm, input a (-) value. If more than 5 mm, input a (+) value.8. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to

standby.

2.6.2. LSU Image Side to Side Adjustment for the Tray1. Insert Letter or A4 size paper into the 1st tray and change the tray setting to the appropriate paper

size. Empty all the remaining trays (including the bypass tray) to disable them.Note:

Do not pull out the 1st tray to disable it when adjusting the 2nd tray. The 1st tray is required as it acts as a paper path for the paper in the 2nd tray.

2. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.3. Perform the Service Mode F1-03 (Print Test Pattern 1).4. Check the gap of the print pattern from the paper edge, refer to the Figure above.5. Perform the Service Mode F6-10 to F6-12, to adjust the gap to be 5 mm.6. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value.7. Proceed the above steps for other Tray.8. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to

standby.

<Figure>Two lines are printed on the top (Lead edge).For Letter or A4, place as Portrait.

5 mmTop (Lead edge)

Two lines are printed

5 mm 5 mm

Two lines are printed

42JUN 2004Ver. 2.0

UF-9000
DP-180/190
2.6.3. LSU Image Side to Side Adjustment for the ADU1. Insert Letter or A4 size paper into the 1st tray and change the tray setting to the appropriate paper

size. Empty all the remaining trays (including the bypass tray) to disable them.2. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.3. Perform the Service Mode F1-06 (Print Test Pattern 4).4. Check the gap of the print pattern from the paper edge, refer to the Figure above.5. Perform the Service Mode F6-16 (ADU Side Adjust), to adjust the gap to be 5 mm.6. If the gap is less than 5 mm, input a (+) value. If more than 5 mm, input a (-) value.7. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to

standby.

2.6.4. Original Registration & CCD Read Adjustments1. Place the Original Document on the Platen Scanner.2. Insert Letter or A4 size paper into the 1st tray and change the tray setting to the appropriate paper

size. Empty all the remaining trays (including the bypass tray) to disable them.3. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.4. Perform the Service Mode F2 (Single Copy Test).5. Check the Image size of the Copy and the Original as Portrait.6. Perform the Service Mode F6-03 (Original Registration), to adjust the Original Registration.7. If the gap is smaller than the Original, input a (-) value. If bigger than the Original, input a (+) value.8. Perform the Service Mode F6-53 (CCD Read Position), to adjust the CCD Read for the side

position.9. If the gap is smaller than the Original, input a (+) value. If bigger than the Original, input a (-) value.

10. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.

2.6.5. ADF Original Read Edge & ADF Main Scan Adjustments1. Place the Original Document on the ADF.2. Insert Letter or A4 size paper into the 1st tray and change the tray setting to the appropriate paper

size. Empty all the remaining trays (including the bypass tray) to disable them.3. Press “FUNCTION”, “ORIGINAL SIZE” keys and then Key “3” on the keypad sequentially.4. Perform the Service Mode F2 (Single Copy Test).5. Check the Image size of the Copy and the Original as Portrait.6. Perform the Service Mode F6-91 (Original Read Edge ADF), to adjust the ADF Original Read Edge.7. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value.8. Perform the Service Mode F6-90 (ADF Image Read Start), to adjust the ADF Main Scan for Side

position.9. If the gap is less than the Original, input a (+) value. If bigger than the Original, input a (-) value.

10. Press "STOP" first and then press "FUNCTION" + "CLEAR" keys simultaneously to return to standby.

43JUN 2004Ver. 2.0

UF-9000
DP-180/190
3 Troubleshooting3.1. Error Codes (For Copier)The self-diagnostic functions detect troubles in the important components of the copier. When trouble occurs, the copier stops.

Note:Some Codes are not used in the UF-9000/DP-180/190, and are reserved for future use.

3.1.1. User Error Codes (U Code)

Note:Uxx and a message will appear on the Panel Display.

User Error Codes (U Code) TableCode Item Check PointsU01 CLOSE FRONT COVER 1. Front Cover is open.

2. Front Cover Sensor is disconnected.3. Front Cover Sensor is defective.4. LVPS connector is disconnected.5. LVPS is defective.6. Engine PCB is defective.

U13 TONER IS RUNNING LOWor OUT OF TONER

1. Toner Cartridge is incorrectly installed.2. Low Toner.3. Toner Sensor is disconnected.4. Toner Sensor is defective.5. Engine PCB connector is disconnected. 6. Engine PCB is defective.

U16 NO CARTRIDGE 1. No Toner Cartridge.U20 CLOSE ADF COVER 1. ADF Cover is open.

2. ADF is not installed correctly.3. ADF Cover Sensor is disconnected. 4. ADF Cover Sensor is defective.5. LVPS connector is disconnected.6. LVPS is defective.

U21 CLOSE PLATEN COVER While the copier is initializing, the ADF Cover was opened.

U52 SCANNER SELF-CHECK 1. SC/SPC PCB connector is disconnected.2. SC/SPC PCB is defective.

U90 REPLACE BATTERY Backup Battery is wearing out.

U21

U20

U90

U13 / U16

U01U52

44JUN 2004Ver. 2.0

UF-9000
DP-180/190
3.1.1.1. Low Toner Messages / OperationThe Toner Cartridge Yield is approximately 5,000 pages using Letter or A4 size paper and 5% Black coverage, however, the maximum yield will not exceed 6,000 pages.The machine controls the printer to maintain good print quality by controlling the Bias Voltage with the Low Toner Sensor and the Print Counter.

There are three Toner warning LCD Displays:LCD 1: [TONER IS RUNNING LOW: U13]

Low Toner sensor detects Low Toner or the machine has printed 5,500 pages.Preparing a new cartridge for replacement is recommended.

LCD 2: [WARNING TONER LOW LESS THAN 50 PAGES]450 pages have been printed since the LCD 1 appeared.Replacement with the new cartridge is recommended.

LCD 3: [OUT OF TONER: U13]50 pages have been printed after LCD 2 appeared or 6,000 pages have been printed.Replace with the new cartridge.

When replacing with a New Cartridge, perform the steps below to reset the Print Counter.1. Press "FUNCTION" key.2. Press "1" or the "Arrow" key to enter "GENERAL SETTINGS".3. Press "SET" key.4. Press "4" to enter "04 TONER REPLACEMENT PRESS SET TO SELECT".5. Press "SET" key, then "TONER REPLACEMENT? 1:Yes 2:No".6. Press "1" key to reset the Print Counter.7. Press "STOP" key to return to the Standby mode.

45JUN 2004Ver. 2.0

UF-9000
DP-180/190
3.1.2. Jam Error Codes (J Code)

Section Jam LocationA ADFB Paper Transport / Exit AreaC Paper Entry Area

Jam Error Codes (J Codes) TableCode Contents SectionJ00 The Registration Sensor did not detect paper within a predetermined time after paper

started feeding. (Sheet Bypass)C

J01 The Registration Sensor did not detect paper within a predetermined time after the Paper Feed Roller started rotating. (1st Feeder Unit)

C

J02 The Registration Sensor does not detect paper within a predetermined time after the Paper Feed Roller started rotating. (2nd Feeder Unit)

C

J43 The Exit Sensor does not detect paper within a predetermined time after the Fuser Unit Paper Exit Sensor is activated.

B, C

J44 The Exit Sensor keeps detecting paper after a predetermined time. B, CJ70 Read Point Sensor does not go ON within 10 seconds after the original starts feeding.

(Information Code 030 is printed on the Transaction Journal instead.)A

J71 Original was longer than 78.7 in (2m).(Information Code 031 or 032 is printed on the Transaction Journal instead.)

A

J79 The ADF Read Point Sensor keeps detecting paper in the ADF. AJ80 The Automatic Duplex Unit (ADU) Entrance Sensor does not detect paper within a

predetermined time. C

J82 The ADU Exit Sensor does not detect paper within a predetermined time after ADU Middle Sensor is activated.

C

J83 The ADU Entrance Sensor keeps detecting paper after a predetermined time has lapsed.

C

J90 The PRINT signal is not received within 1 minute after the FEED signal is received. -J91 The Paper Tray was pulled out when feeding a paper. CJ92 The Front Cover was opened when feeding a paper. CJ93 The paper remained in the ADF. A

A

B

C

46JUN 2004Ver. 2.0

UF-9000
DP-180/190
• Sensor and Switch Location

47JUN 2004Ver. 2.0

UF-9000
DP-180/190
3.1.2.1. Copy / Print Over Flow / FlowService Mode F5-10: Exit Tray Limitation (Paper Stack Limitation)

0: None1: 150 Sheets/Accumulate2: 150 Sheets/Job

Copy or Print

Yes

No

Select 1 or 2

FAX/EMAIL

Is the job larger than 150 pages?

Normal Function

If next Job is performed at this point in time

Stop printing when 150 pages print out

Warning Display Cancel Job?

Job ClearPrint the Remaining Job Pages

Copy or Print

Is Sort Memory Space Available?

Wait for Previous Job to Complete

After Pending Job is Completed, Printing Will Start

Start Print Count from 0

Add the Previous Page of a Job as Accumulative Print Count

Cancel "Pi Pi Pi" Sound

*1 : Same Function as when the next print job is received in Queue during Paper Jam

*1

1

Time Out -> Error Display on Print Queue Screen

START

STOP

Print

Copy

Yes

No

F5-10: [2]

F5-10: [1]

Yes

No

EXIT TRAY FULL:EMPTY & PRESS START

COPY, PRINT mode

FAX/EMAIL, SCAN modeEXIT TRAY FULL:PRESS COPY

1

48JUN 2004Ver. 2.0

UF-9000
DP-180/190
3.1.3. Mechanical Error Codes (E Code)

E1: Optical Unit ErrorCode Function Check Points

E1- 01 Abnormal Platen Glass Scanning

1. Home Position Sensor connector is disconnected.2. Home Position Sensor is defective.3. Scanner Motor connector is disconnected.4. Scanner Motor is defective.5. Scanning Mechanism is defective.6. SPC PCB connector is disconnected.7. SPC PCB is defective.8. LVPS is defective.

E1- 22 Polygon Motor Synchronization 1. Engine PCB connector is disconnected. 2. Engine PCB is defective.3. Laser Unit is defective.4. LVPS connectors is disconnected. 5. LVPS is defective.6. SC PCB is defective.

E1- 31 Scanning Lamp (does not turn On)

1. Scanning Lamp connector is disconnected.2. Scanning Lamp is defective. 3. SPC PCB connector is disconnected.4. SPC PCB is defective.5. SC PCB is defective.

E2: Lift DC Motor ErrorCode Function Check Points

E2 Not Applicable -

E3: Development System ErrorCode Function Check Points

E3- 20 Main Motor Rotation 1. Drive Mechanism is defective.2. Main Motor connector is disconnected.3. Main Motor is defective.4. Engine PCB connector is disconnected. 5. Engine PCB is defective.6. LVPS is defective.

E4: Fuser Unit ErrorCode Function Check PointsE4- 01 Fuser Warm-up Temperature 1. Fuser Thermistor is dirty.

2. Thermistor position is incorrect. 3. Fuser temperature is low.4. Thermistor is defective. 5. Fuser Lamp connector is disconnected. 6. Fuser Thermostat is defective.7. Fuser Lamp is defective. 8. Engine PCB connector is disconnected. 9. Engine PCB is defective.

49JUN 2004Ver. 2.0

UF-9000
DP-180/190
Note:These error codes will appear only when the optional accessories are installed.

E4- 10 Exhaust Fan Motor Rotation (Fuser Unit Side)

1. Exhaust Fan connector is disconnected.2. Exhaust Fan is defective. 3. LVPS connector is disconnected.4. LVPS is defective.5. Engine PCB is defective.

E5: System ErrorCode Function Check PointsE5- 05 SPC Firmware Failure 1. SPC PCB is defective.E5- 11 Thermistor, Toner Sensor 1. SC/Engine PCB connector is disconnected.

2. SC/Engine PCB is defective.E5- 12 Main CPU/SPC Interface Error 1. SC/SPC PCB connector is disconnected.

2. SC/SPC PCB is defective.

E7: Optional Unit ErrorCode Function Check PointsE7- 90 Hardware Key Error Incorrect Hardware Key is installed.

E13: Low Toner or Out of TonerCode Function Check PointsE13 TONER IS RUNNING LOW

or OUT OF TONER

1. Toner Cartridge is incorrectly installed.2. Out of Toner.3. Low Toner Sensor is disconnected.4. Low Toner Sensor is defective.5. Engine PCB connector is disconnected. 6. Engine PCB is defective.

E4: Fuser Unit ErrorCode Function Check Points

50JUN 2004Ver. 2.0

UF-9000
DP-180/190
3.2. Information Code Table (For Facsimile)

Fax Information CodesCode Mode Phase Description of Problem Cause001 RCV

COPYC, D Leading edge of the recording

paper fails to reach the Timing Sensor. (1st Tray)

Recording paper jam.Timing Sensor abnormal.

002 RCVCOPY

C, D Leading edge of the recording paper fails to reach the Timing Sensor. (2nd Tray)

Recording paper jam.Timing Sensor abnormal.

007 RCVCOPY

C, D 1. Leading edge of the recording paper fails to reach the Paper Exit Sensor.

2. Recording paper has not completely passed the Paper Exit Sensor.

Recording paper jam.Paper Exit Sensor abnormal.

008 Paper Tray is opened while paper is feeding.

Paper Tray is opened.

010 RCVCOPY

B, C No recording paper. No recording paper or paper is not setproperly.No Paper Sensor is defective.

011 STANDBY B, C Paper Tray is not installed properly.

Connector is not installed properly.

012 RCV C, D The length of the received document is over 2 m.

Transmitter Document Jam.

017 Incorrect paper size loaded in the Paper Tray.

Paper size is incorrect.

030 XMT B Read Point Sensor does not go ON within 10 seconds after the document starts feeding.

Document is not set properly.Defective Read Point Sensor.

031 XMTCOPY

C Transmitting document was longerthan 2 meter (or 78.7 in).

The document may jam.Defective Read Point Sensor.

041 STANDBYRCV

COPY

B, C, D Out of Toner. No toner.Defective Low Toner Sensor.

043 STANDBYRCV

COPY

B, C, D Low Toner. Toner is getting low.Defective Low Toner Sensor.

045 STANDBY - No Toner Cartridge. Toner Cartridge has not been installed.Defective Toner Cartridge Sensor.

060 - A Printer Cover is open. Cover is not firmly closed.Connectors are not firmly connected.

061 - A ADF Door is open. Door is not firmly closed.Connectors are not firmly connected.

400 XMT B T1 timer (35 ± 5 sec.) elapsed without detecting 300 bps signal.

Incorrect number was dialed and the START button was pushed.Telephone line was disconnected while dialing.SC PCB (Modem) or MJR PCB are defective.Receiver is defective. (It may only be transmitting CED)

51JUN 2004Ver. 2.0

UF-9000
DP-180/190
401 XMT B DCN was returned from receiver while transmitter is waiting for CFR or FTT.

Your machine's ID Number is not programmed.Possible incompatibility or incorrect Password.

402 XMT B DCN was returned from receiver while transmitter is waiting for NSF/DIS.

Receiver working in non-CCITT mode only. (Possible incompatibility)

403 RCV(Polling)

B Transmitter had no polling function.

"POLLED=ON" (polling XMT ready) is not set at the transmitter. Document to be transmitted is not placed at the transmitter.

404 XMT B Transmitter sent NSS (or DCS) followed by TCF three times, but the receiver did not respond. (CFR or FTT is usually returned)

Receiver is defective. (Modem)SC PCB or FXB PCB are defective.Receiver disconnects line during first NSS (or DCS) is transmitted.

405 XMT B Transmitter received FTT after it transmitted TCF at 2400bps.Received RTN after communicating at 2400 bps.

Line quality is poor. (TCF is damaged due to line noise)Receiver is defective. (Modem, etc.) SC PCB or FXB PCB are defective.

406 RCV(Password

Comm.)

B XMT-Password mismatched.RCV-Password mismatched.Selective RCV incomplete.

XMT, RCV password does not match.Last 4 digits of TSI does not match withthe last 4 digits of ONE-TOUCH, ABBRtelephone number.

407 XMT D Transmitter received no response after it transmitted post message, such as EOP, MPS, EOM, etc...or received DCN.

Receiver is defective. (No paper, paper jamming, etc.) Receiver ceased receiving because of excessive error. (Line quality is poor) SC PCB or FXB PCB are defective.

408 XMT D Transmitter received RTN after it transmitted EOP, MPS, or EOM.

Receiver receives data with error. (Line quality is poor) Receiver is defective. (Modem, etc.)SC PCB or FXB PCB are defective.

409 XMT D Transmitter receives PIN after it transmitted a post message, such as EOP, MPS, EOM, etc.

Receiver receives data with error due to poor line quality, and receiving operator requests voice contact.Receiver is defective. (Modem, etc.)SC PCB or FXB PCB are defective.

410 RCV D Received DCN while waiting for post command. (EOP, MPS, EOM, etc.)

Interface or line is faulty.Transmitter is defective.

411 RCV(Polling)

B Received DCN after transmitting NSC.

Transmitter is not ready for polling communication. Password does not match between transmitter and receiver.

412 G3 RX B, D No response within 12 seconds in NSS/DCS/MPS wait state. (After transmitting FTT)

Transmitter is defective.SC PCB is defective.

414 RCV(Polling)

B No response received after transmitting 3rd NSC.

Password does not match between transmitter and receiver.Transmitter is defective. (No original, document jam, etc.)

Fax Information CodesCode Mode Phase Description of Problem Cause

52JUN 2004Ver. 2.0

UF-9000
DP-180/190
415 XMT(Polling)

B Remote side attempted to receive message from your machine in polling communication.

Inform the remote side that your machine does not have the polling transmission feature.

416 RCV D Receiver did not detect post command, such as EOP, MPS, EOM, etc.

Transmitter is defective.Line quality is poor. (RTC signal is distorted due to line noise)SC PCB or FXB PCB are defective.

417 RCV C Receiver returned RTN in response to post message.

Line quality is poor. (There are excessive errors in received data)SC PCB or FXB PCB are defective.

418 RCV C Receiver transmitted PIN in response to PRI-Q from transmitter. (Transmitting operator requests voice contact)

Line quality is poor. (There are excessive errors in received data)SC PCB or FXB PCB are defective.

420 RCV B T1 timer (35 sec.) elapsed without detecting 300 bps signal.

Incorrect incoming call type (voice). (Non-facsimile communication)Transmitter is defective.SC PCB or FXB PCB are defective.

421 RCV B Busy Tone is detected after sending NSF Signal.

Remote station disconnected the line.Wrong number is dialed.

422 XMT B Content of NSF (or DIS) or NSC (or DTC) was invalid.

There is an incompatibility.

427 G3 RCV

B DCN received to NSF/CSI/DIS transmitted.

The interface is incompatible.

434 XMT or RCV B CD (response from Modem) did not turn OFF within 180 sec. after receiver detected FLAG signal.

Remote unit is defective.SC PCB or FXB PCB are defective.

436 G3 RX C DCN received after transmitting FTT.

Transmitter is defective or incompatible.Line quality is poor.

456 RCV B Received relay transfer request or confidential document to distribute to an end receiving station or all confidential mailboxes are used.

457 RELAY XMT CONF. XMT/

POLL

B Remote unit does not have Relayed XMT or Confidential Comm. capability.

459 RCV C Failed training in Phase C. Line quality is poor. (Training signal is distorted due to line noise)SC PCB or FXB PCB are defective.

490 RCV C Sum of error lines exceeded the limit (Function Parameter No. 70) of 64 lines.

Line quality is poor.SC PCB or FXB PCB are defective.

494 RCV C Interval between two EOLs was more than 10 sec. when receiver received message data.

Transmitter is defective.Line quality is poor. (EOL is damaged due to line noise)SC PCB or FXB PCB are defective.

495 XMT RCV

C During reception, CD turned OFF or continued ON for long time. During communication, lost loop - current.

Line is disconnected.Transmitter is defective.SC PCB or FXB PCB are defective.


53JUN 2004Ver. 2.0

UF-9000
DP-180/190
496 XMT C CS of modem is not able to turn ON.

FXB PCB is defective.

501 XMT/RCV(V.34)

B Remote unit does not have compatible Modem.

502 XMT/RCV(V.34)

B, C, D During reception, CD turned OFF or continued ON for long time. During communication, lost loop - current.

Line is disconnected.Transmitter is defective.SC PCB or FXB PCB are defective.

503 XMT/RCV(V.34)

B, C, D CS of modem is not able to turn ON during training.

FXB PCB is defective.Line is disconnected.

504 RCV/V.34(Polling)

B Polling is rejected from the remote station.

No polling original is set.

505 XMT/V.34(Polling)

B Polling XMT is rejected. No polling original is set.

540 XMT ECM B No response after transmitting 3rd CTC or DCN received.

Incompatible interface.

541 XMT ECM D No response after transmitting 3rd EOR or received DCN.

Line is faulty.FXB PCB abnormal.

542 XMT ECM D No response to the 3rd RR transmitted or received DCN.

Remote unit is abnormal.

543 XMT ECM D T5 timer (60 sec.) elapsed without MCF.

Remote unit is abnormal.

544 XMT ECM D Stopped Transmission after EOR Transmission.

Line is faulty.FXB PCB abnormal.

550 RCV ECM C Timer between frames in phase C has elapsed.

Defective remote station.

554 RCV ECM D Transmitted ERR after receiving EOR.

Line is faulty.

555 RCV ECM D Transmitted PIN after receiving EOR.

Line is faulty and Operator Call requested by RX side.

570 RCV B Password or machine code did not match during remote diagnostic communication.

571 XMT B Remote unit did not have the remote diagnostic function.

580 XMT B Sub-address transmission to a unit that has their DIS bit 49 (NSF bit 155) OFF.

Sub-address transmission to a unit that has no Sub-address function.

581 XMT B Sub-address Password transmission to a unit that has their DIS bit 50 (NSF bit 156) OFF.


582 XMT B Sub-address SEP (for Polling) transmission to a unit that has their DIS bit 47 (NSF bit 130) OFF.


601 XMT ADF Door was opened during ADF transmission.

623 XMT A No original was in the ADF. (Built-in dialer engaged)

Operator removed the original from the ADF after dialing was completed.Original was not set properly in the ADF.


54JUN 2004Ver. 2.0

UF-9000
DP-180/190
630 XMT or RCV(Polling)

B Redial count over. No dial tone detected. Sensor dial tone is not detected. (destination dependent)Busy tone is detected. (destination dependent) T1 timer (35 ± 5 sec.) elapsed without a signal from the receiver.

631 XMT A "STOP" button was pressed during Auto Dialing.

634 XMT B Redial count over with no response or busy tone was not detected.Note:

U.S.A. and Canadian models will redial only once if a busy tone is not detected.

Telephone line cable is disconnected.Wrong number is dialed.SC or FXB PCB is abnormal.

638 XMT LAN Power turned Off with applicable data in memory or during communication.

Power switched off. Power failure occurred.

711 RCV LAN Incorrect LDAP settings. LDAP Server Name, LDAP Login Name, LDAP Password and/or LDAP Search Base are incorrect.

712 XMT LAN Unknown email address replied from the Mail Server.

Mail Server received an incorrect email address. (Dependent on Server's Mail application)

714 XMT RCV

LAN LAN Interface error.Cannot logon to the LAN.

The 10Base-T/100Base-TX cable is not connected.An unexpected LAN problem occurred.Check the SC PCB connector.

715 XMT LAN TCP/IP connection timed out. Incorrect IP Address is set.Verify the IP Address, Default Router IP Address, SMTP Server IP Address.

716 XMT LAN Cannot logon to the LAN. Incorrect SMTP Server IP Address is set.No email application is activated on the Mail Server.

717 XMT LAN Incomplete SMTP Protocol transmission.

Mail Server’s hard disk may be full.Mail Server is defective.

718 XMT LAN Page Memory Overflow occurred while receiving printing data. The paper size selected within your application to print is larger than the paper size loaded in the Tray(s).

Check the document size and resolution.Ask originator to re-send in a supported size and resolution.

719 RCV LAN Received data via LAN is in a format that is not supported.

Ask the originator to re-send with a supported file attachment:

* In a TIFF-F format.* Image data conforming to A4/Letter size.

720 POP LAN Unable to connect with the POP Server.

Incorrect POP Server address is set.POP Server is down.

721 POP LAN Unable to login to the POP Server. Incorrect User Name or Password is set.


55JUN 2004Ver. 2.0

UF-9000
DP-180/190
722 RCV LAN Failed to obtain the Network Parameters (such as: IP Address, Subnet Mask, Default Gateway IP Address, etc.) from the DHCP server.

LAN Cable is disconnected.DHCP is not available.(Contact the Network Administrator.)

725 XMT POP

LAN DNS Server connection timed out. Incorrect DNS Server address is set.DNS Server is down.

726 XMT POP

LAN Received an error response from the DNS Server.

Incorrect POP Server address is set.Incorrect SMTP Server address is set.

728 XMT LAN Received an Error or No Response from the RemoteInternet Fax. (SMTP Direct XMT)

Remote Internet Fax Errors: Busy,Memory Overflow, or No Power.Job Number Overflow for Relay XMT

729 XMT LAN Failed to authenticate (SMTP AUTHENTICATION) when connecting with the SMTP server.

SMTP AUTHENTICATION, User Name and/or Password are incorrect.(Contact the Network Administrator.)

730 RCV LAN Unable to program the Internet parameters or the autodialer with Email from a PC.

Verify that the Fax Parameter #158 is set to 2: Valid.

731 RCV LAN Dialer full while Relayed Transmission Request was received.

Dial buffer for manual number dialing (70 stations) are being used.

741 XMT, Polling PSTN Unable to dial Deleted the registered station name before dialing with Timer Controlled Communications, etc.

800 Relay Comm.

PSTN The machine was requested to relay a document but has no Relay Hub capability.

814 Conf. XMT Conf. Polling

Relay Comm.

The remote station does not have Relay XMT nor Confidential Communication capability.

815 Conf. RCV Mailbox is full.816 Conf. Polled "The received Polling Password

did not match. The machine does not have Confidential Comm. capability."

825 Conf. RCVConf. Polled

Parameter settings of the initial sending station are not properly set.

826 RCV B If applicable sub-address is not registered in the phone book of the receiver side when using sub-addressing function.

Receiver side does not have correct sub-address in their phone book.

870 MEM XMT Multi-Copy

PSTN Memory overflow occurred while storing documents into memory.

879 MemoryRCV

PSTN Memory overflow occurred during substitute memory reception.

Memory overflow on the Fax side.

LAN Memory overflow.Mail Server sent a reset command while downloading the data to the machine.

Memory overflow on the Fax side.Mail server aborted the download (Busy with other higher priority jobs).


56JUN 2004Ver. 2.0

UF-9000
DP-180/190
880 - - File Access Error.884 - - File Access Error.961 RCV LAN Memory file access error. SC PCB is defective.962 XMT PSTN Memory file access error. SC PCB is defective.

LAN Memory file access error. SC PCB is defective.


57JUN 2004Ver. 2.0

UF-9000
DP-180/190
4 Service Modes4.1. Service Modes (For Copier)These Service Modes are provided to assist the technician in checking for abnormalities in the copier and a means of making adjustments to the Input/Output of major components.

4.1.1. Service Mode Procedure

1. To select the Service ModeThe service mode is selected when “FUNCTION”, “ORIGINAL SIZE” and “3” keys are sequentially pressed, then F1 will appear in the display.

2. To exit the Service ModeThe service mode is reset when the “FUNCTION” and “CLEAR” keys are pressed simultaneously.

4.1.2. Copier Service Mode Functions

Service Modes (For Copier)Service Mode Item Function

F1 Self Test 00 CCD Test This test is used for checking the CCD.01 LCD/LED Test This test is used for checking the LCD

and LEDs.02 Page Memory Test This test is used for checking the Page

Memory.03 Print Test Pattern 1 Prints the pattern for setting the Paper

position alignment.04 Print Test Pattern 2 Prints the Slant pattern for setting the

Paper position alignment.05 Print Test Pattern 3 Prints the Grid pattern for setting the

Paper position alignment.06 Print Test Pattern 4 Prints the pattern for setting the Duplex

Paper position alignment.F2 Single Copy Test One sheet is copied when the Start key

is pressed.F3 Continuous Copy Test Multi copies are made when the Start

key is pressed.F4 Input / Output Status Test The functioning of Input / Output items

(selected item numbers) is checked.F5 Function Parameters Various function settings (selected by

code numbers) can be changed.F6 Adjust Parameters Various function settings (selected by

code numbers) can be adjusted.F7 Electronic Counter Electronic Counters for MaintenanceF8 Service Adjustment Perform pseudo-operation of an item

(selected by code numbers)

58JUN 2004Ver. 2.0

UF-9000
DP-180/190
F9 Unit Maintenance

00 Fax Function Parameter01 Service Alert Tel # Displays the contact number when a

machine malfunction occurs.02 Firmware Version Displays the firmware version for SC,

SC Boot, PNL, SPC, Fax Option, Slot 1.03 Print Device Info. F5/F6 Parameter, Machine / Counter /

System Address / RAM Address informations.

04 RAM Edit Mode Relative / Absolute Address.05 Serial Number Registration of Serial Number for

Maintenance.06 RAM Initialize Each RAM date clear.

Except F5, F6 Settings - refer to F6-99 "F5/F6 Initialization"

07 Firmware Update Updates the firmware in the machine Firmware Card or the USB.

08 Program Backup Refer to Sect. 2.5.09 Update Prog. Card Creates a Master Firmware Card using

the Firmware Update Kit.10 Program Copy Configuration for Program copy.11 Parameter Backup Backup the Parameter.12 Parameter Restore Restore the Parameter.13 Page Memory Size Displays the page memory size (MB).14 Sort Memory Size Displays the sort memory size (MB).

Service Modes (For Copier)Service Mode Item Function

59JUN 2004Ver. 2.0

UF-9000
DP-180/190
F5 / F6 Information List (Sample)

**********-F5/F6 INFORMATION LIST-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01

F5-00 . . . . . F5-50 Auto contrast adj. Yes F5-01 Frequency desired 60Hz F5-51 Dept. Counter (COPY) NoF5-02 . . . . . F5-52 Dept. Counter (FAX) NoF5-03 . . . . . F5-53 2-sided auto shift NoF5-04 LSU off timer 5 Sec. F5-54 . . . . .F5-05 . . . . . F5-55 . . . . .F5-06 . . . . . F5-56 . . . . .F5-07 . . . . . F5-57 . . . . .F5-08 . . . . . F5-58 . . . . .F5-09 . . . . . F5-59 Ope.add toner alarm Stop

F5-10 Exit Tray Limitation None F5-60 Auto Tray selection YesF5-11 . . . . . F5-61 . . . . .F5-12 . . . . . F5-62 . . . . .F5-13 Paper out Indicator On F5-63 U13 clear Any keysF5-14 Paper size (Tray1) Letter-R F5-64 Dept. Counter (SCAN) NoF5-15 Paper size (Tray2) Letter-R F5-65 Dept. Counter (PRINT) NoF5-16 . . . . . F5-66 . . . . .F5-17 . . . . . F5-67 . . . . .F5-18 . . . . . F5-68 . . . . .F5-19 . . . . . F5-69 Reduce N in 1 space No

F5-20 ADF Auto F5-70 PM cycle 85KF5-21 . . . . . F5-71 . . . . .F5-22 . . . . . F5-72 . . . . .

60JUN 2004Ver. 2.0

UF-9000
DP-180/190
2.FIRMWARE VERSION SC : BAT001xxAU

1.MACHINE INFORMATION MACHINE NAME : UF-9000 MAC ADDRESS : 080023016C81 SERIAL NUMBER :

SC BOOT : V006 PNL : V010018 SPC(SCANNER) : V6493 PRINTER : V00039 FAX MODEM : Ver 6D01 PDL FONT1 : CAV10000b SC2 : CAV13500aAU

3.MEMORY CAPACITY PAGE MEMORY : 32 MB SORT MEMORY : 16 MB FAX MEMRY : 2 MB 4.OPTION 2nd PAPER FEED MODULE : No PCL PRINTER : No PS PRINTER : No HDD : No

5.ERROR LOG TOTAL PRINT COUNT : 503 NO. DATE & TIME ERROR CODE ERROR COUNT NO. DATE & TIME ERROR CODE ERROR COUNT -------------------------------------------------------------------------------- 01 MMM-dd-yyyy 11:11 J97 XX-00000008 02 MMM-dd-yyyy 11:31 J44 XX-00000140 (See Remarks) --------------------------------------------------------------------------------

**********-MACHINE SETUP INFORMATION-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01

******************************* - - ***** - 0001- *********

Machine Setup Information List (Sample)

Remarks: XX-00000140

00 : Printer Error 02 : Scanner Error

Page Count

-PANASONIC -

61JUN 2004Ver. 2.0

UF-9000
DP-180/190
F7 Total Counter List (Sample)

F7-01 Key Operator ID Code : 000

F7-02 Total Count : 295F7-03 PM Count : 295F7-04 Scanner PM Count : 61F7-05 . . . . . : F7-06 OPC Drum Count : 295F7-07 Process Unit Count : 295F7-08 ADF PM Count : 50F7-09 . . . . . :F7-10 . . . . . :

F7-11 Sheet Bypass Count : 147F7-12 1st Paper Tray Count : 90F7-13 2nd Paper Tray Count : 0F7-14 . . . . . :F7-15 . . . . . :F7-16 2-Sided Count : 28F7-29 . . . . . :F7-30 A4R/LTR Count : 73F7-31 . . . . . :F7-32 FLS/LG Count : 0

F7-17 ADF Count : 26F7-18 ADF Read Count : 26F7-19 Scanner Count : 61F7-20 Scanner Read Count : 18

F7-21 Copy Rint Count : 59F7-22 Copy Scan Count : 180

F7-23 PC Rint Count : 0F7-24 PC Scan Count : 3

F7-24 Fax Transmit Count : 24F7-24 Fax Receive Count : 27F7-24 Fax Print Count : 21

Serial Number :

**********-F7 TOTAL COUNTER LIST-****** DATE MMM-dd-yyyy *** TIME12:01 *** P.01

62JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.1.3. F4 Mode: Input/Output Status Test

Set the machine to service mode and press "4" key on the Keypad.↓

Press the "START" key.↓

Select “1:Check Input“ or “2:Check Output“ to activate the test then press "START" key.↓

Press "STOP" key to cancel the test.↓

When the “CLEAR” key is pressed, the selected code input will not be accepted.↓

Press “FUNCTION” and “CLEAR” keys simultaneously to exit the service mode.

1. Check Input

2. Check Output Press the "START" key to start and press the "STOP" key to reset.

F4 Mode (Check Input)

No. Function Condition Message Display Remarks7 6 5 4 3 2 1 0

021 Home Position Sensor Home position is detected.

1

ADF Cover Open Sensor ADF Cover is open. 1

F4 Mode (Check Output)No. Item Function Remark120 Lamp When SPC PCB P103-8, Inverter

CN1-2 signal level changes to 0V from Open, Lamp operates.

The CCD / Inverter shall be replaced as the Assembly

63JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.1.4. F5 Mode: Function Parameters (For Copier)

Set the machine to Service Mode and press "5" key on the Keypad.↓


Enter the desired code number or press “V”, ”/\” arrow keys.↓

Press the "SET" key.↓

Enter the desired function code number and press “SET” key.↓


Press “STOP” key, then press “FUNCTION” and “CLEAR” keys simultaneously to exit the service mode.↓

Reboot the machine after setting the parameter(s) to activate the setting(s).

F5 ModeNo. Item Function Default Setting00 Not Used01 Frequency Desired 0 : Auto

1 : 50 Hz2 : 60Hz

2 (for USA / Canada)

1 (for Europe)02-03 Not Used

04 LSU Off Timer 1 : 5 sec. 2 : 10 sec. 3 : 15 sec. 4 : 20 sec. 6 : 30 sec. 8 : 40 sec.10 : 50 sec.12 : 60 sec.

1

05-09 Not Used10 Exit Tray Limitation

(Up to 150 Sheets)0 : None1 : Accumulate2 : Job

0(Effective from June 2004 Production)

11-12 Not Used13 Paper Out Red Indicator 0 : On

1 : Off0

14 Paper Size (Tray 1)(UF-9000)

4 : A4-R12 : LEGAL14 : LETTER-R


4 (for Europe / Others)

Paper Size (Tray 1)(DP-180/190)

4 : A4-R 6 : B5-R 8 : A5-R12 : LEGAL14 : LETTER-R

64JUN 2004Ver. 2.0

UF-9000
DP-180/190
15 Paper Size (Tray 2)(UF-9000)

4 : A4-R12 : LEGAL14 : LETTER-R 14 (for USA / Canada)

4 (for Europe / Others)Paper Size (Tray 2)(DP-180/190)

4 : A4-R 6 : B5-R 12 : LEGAL14 : LETTER-R

16-19 Not Used20 ADF 0 : No

1 : Auto1

21-37 Not Used38 Duplex Mode Default

(UF-9000)0 : No1 : 1 to 22 : 2 to 2

0

39 Not Used40 Double Count 0 : No

2 : LGL0 : UF-9000/DP-190

41 Count Up Timing 0 : At feed1 : At exit

1

42 KEY/DEPT. Counter 0 : No2 : DEPT.

2

43 Key Counter Timing Same as F5-41 044-49 Not Used

50 Auto Contrast Adjust 0 : No1 : Yes

1

51 Dept. Counter (COPY) 0 : No1 : Yes

0

52 Dept. Counter (FAX) 0 : No1 : Yes

0

53-58 Not Used59 Oper. Add Toner Alarm 0 : Stop

1 : Continue0

60 Auto Tray Selection 0 : No1 : Yes

1

61-62 Not Used63 U13 Clear

(DP-180/190 only)0 : Any keys1 : Func + 1

0

64 Dept. Counter (SCANNER) 0 : No1 : Yes

0

65 Dept. Counter (PRINTER) 0 : No1 : Yes

0

66-68 Not Used69 Reduce N in 1 Space 0 : No

1 : Yes0

F5 ModeNo. Item Function Default Setting

65JUN 2004Ver. 2.0

UF-9000
DP-180/190
70 PM Cycle 0 : No 1 : 1.5 K 2 : 2.5 K 3 : 5 K 4 : 10 K 5 : 15 K 6 : 20 K 7 : 30 K 8 : 40 K 9 : 60 K10 : 85 K*11 : 90 K12 : 120 K13 : 150 K14 : 200 K15 : 240 K

0 (for UF-9000)Effective from April 2004 Production

10 (for DP-180/190)

* Effective from June 2004 Production

71-78 Not Used79 Image Process Method 0 : Error Diffusion

1 : Dither0

80 Paper Size Priority 4 : A4-R 5 : B5 7 : A5 9 : FLS110 : FLS212 : LEGAL14 : LETTER-R


4 (for Europe / Others)

81 Foolscap Size 1 : FLS12 : FLS2

1

82 Not Used83 Digital Skyshot Mode 0 : Off

1 : On0

84 Paper Tray Priority 0 : S > C > B1 : C > S > B

0

85 Side Void Setting (ADF) 0 : No1 : Yes

0

86 PM Cycle (Optics) 0 : No1 : 40 K2 : 60 K3 : 120 K4 : 240 K5 : 360 K6 : 480 K7 : 600 K

0

87 PM Cycle (ADF) 0 : No1 : 40 K2 : 60 K3 : 120 K4 : 240 K5 : 360 K6 : 480 K7 : 600 K

0


66JUN 2004Ver. 2.0

UF-9000
DP-180/190
88 USB Port Function 0 : Off1 : Once2 : On

0

89 LAN Speed/Duplex 0 : Auto 1 : 10 Half 2 : 10 Full 3 : 100 Half 4 : 100 Full

0

90 Beep Sound 0 : Off1 : Soft2 : Loud

1

91-94 Not Used95 Paper Size (FA)

(Factory use only)0 : Japan1 : USA/CAN2 : Europe3 : Other

1 (for USA / Canada)2 (for Europe)

96-97 Not Used


67JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.1.5. F6 Mode: Adjust Parameters (For Copier)








Reboot the machine after setting the parameter(s) to activate the setting(s).Note:

1. The Factory Setting is different in each model.2. The machine may accept a (+/-) input value that exceeds the specified Setting Range for the

parameters in the table; however, the actual registered value will not exceed the Upper/Lower Limitation value.

F6 Mode

No. Item Remarks Setting Range

00-02 Not Used03 Original Registration Adjustment of platen original registration

detection timing.-30 - +30 0.2mm

04 Printer Registration Delay time is adjusted from registration roller clutch ON.

-50 - +16 0.5mm

05-06 Not Used07 Registration Void Registration void should be adjusted. 0 - +99

0.5mm08 Trail Edge Read Timing Adjustment of trail edge void. -9 - 0

0.5mm09 Trail Edge Print Timing Adjustment of trail edge void. -9 - +15

0.5mm10 Side Adjust (Bypass) Adjustment of LSU side-side (Sheet Bypass). -8 - +7

0.5mm11 Side Adjust (Tray 1) Adjustment of LSU side-side (1st Tray). -8 - +7

0.5mm12 Side Adjust (Tray 2) Adjustment of LSU side-side (2nd Tray). -8 - +7

0.5mm13-15 Not Used

16 Side Adjust (ADU) Adjustment of LSU side-side (ADU). -8 - +7 0.5mm

17-32 Not Used33 TDC Max. Read Only Set by Digital QUANTUM (QUARC) control -99 - +99

(Read only)34 TDC Min. Read Only Set by Digital QUANTUM (QUARC) control -99 - +99

(Read only)

68JUN 2004Ver. 2.0

UF-9000
DP-180/190
35 TDC Avg. Read Only Set by Digital QUANTUM (QUARC) control -99 - +99 (Read only)

36-38 Not Used39 LSU Unit PWM Adjust Adjustment of PWM value of LSU. -32 - +3240 Trans Current Side 1 Adjustment of Transfer Current. -77 - +76

0.15uA41-43 Not Used

44 FAX Laser Duty Adj Printer Density Adjustment for FAX. (-) : Darker.(+) : Lighter.

-99 - +99

45 Not Used46 PRINTER Laser Duty Adj Printer Density Adjustment for Printer.

(-) : Darker.(+) : Lighter.

-99 - +99

47-48 Not Used49 TEXT Image Density Image density adjustment for Text mode.

(-) : Darker.(+) : Lighter.

-99 - +99

50 T/P Image Density Image density adjustment for Text/ Photo mode.(-) : Darker.(+) : Lighter.

-99 - +99

51 PHOTO Image Density Image density adjustment for Photo mode.(-) : Darker.(+) : Lighter.

-99 - +99

52 Not Used53 CCD Read Position Adjustment of CCD read position. -42 - +44

0.2mm54 TEXT Mode Contrast Adjustment of Contrast for Text Mode. -128 - +12755 T/P Mode Contrast Adjustment of Contrast for Text/Photo Mode. -128 - +12756 PHOTO Mode Contrast Adjustment of Contrast for Photo Mode. -128 - +127

57-62 Not Used63 Lead Edge Read Timing Adjustment of Lead Edge Read Point. 0 - +9

0.5mm64 Side Edge Read Adjust Adjustment of Side Edge Read Point. 0 - +9

0.5mm65-66 Not Used

67 ADF Image Density Compensation of ADF image density. -99 - +9968 Not Used69 Stamp Position Adjust Adjustment of verification stamp position. -50 - +50

0.3mm70-78 Not Used

79 MTF Adjust Adjustment of Scanning Sharpness by digital image processing for Text /Photo Copy Mode.

-2 - +2

80-89 Not Used90 ADF Image Read Start Adjustment of ADF horizontal image read

start position. -99 - +99 0.05mm

F6 Mode


69JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.1.6. F7 Mode: Electronic Counter









91 Original Lead ADF Adjustment of original detection timing. -99 - +99 0.3mm

92 Original Trail ADF Adjustment of trail edge detection timing. -90 - +127 0.3mm

93-98 Not Used99 F5/F6 Initialization Initialize F5/F6 parameter settings.

F7 ModeNo. Item Remarks01 Key Operator ID Code Key Operator’s identification code for access to the

counter mode.02 Total Count Total count for all copies / prints.03 PM Count Preventive Maintenance count.04 Scanner PM Count PM count for scanner readings.05 Not Used06 OPC Drum Count PM count of recording paper fed through the OPC

Drum.07 Process Unit Count PM count of recording paper fed through the

Process Unit.08 ADF PM Count PM count of originals fed through the ADF.

09-10 Not Used11 Sheet Bypass Count Total count of paper fed from the sheet bypass.12 1st Paper Tray Count Total count of paper fed from the 1st paper tray.13 2nd Paper Tray Count Total count of paper fed from the 2nd paper tray.

14-15 Not Used16 2-sided Count Total count of 2-sided Print.17 ADF Count Total count of originals fed through the ADF.18 ADF Read Count Total count of originals scanned through the ADF.

F6 Mode


70JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.1.7. F8 Mode: Service Adjustment








19 Scanner Count Total count of scanning operations.20 Scanner Read Count Total count of scanner readings.21 Copy Print Count Total count of copies printed.22 Copy Scan Count Total count of copies scanned.23 PC Print Count Total count printed from PC.24 PC Scan Count Total count scanned to PC.25 Fax Transmit Count Total count of Fax transmitted.26 Fax Receive Count Total count of Fax received.27 Fax Print Count Total count of Fax printed.

28-29 Not Used30 A4R / LETTER R Count Total count of A4-R / Letter-R Print.31 Not Used32 FLS / LEGAL Count Total count of FLS / Legal Print.99 All Counter Clear All counters are cleared.

F8 ModeNo. Item Remarks

00-05 Not Used06 Error Log View a) Each time the arrow key is pressed, the machine

errors or paper jam codes stored in memory are displayed, beginning with the oldest code.

Note:Only the 30 most recent codes are displayed.

07 Error Log Clear a) Press the Reset key.A Message "Error code can be cleared with the Start key" is displayed on the LCD.*

b) Press the Start key.08 (Factory use only) Lock operation for Scanner Unit.

09-17 Not Used18 C18 PRT PWM ADJ.PTN.

(LSU PWM Pattern)Print out the Test Pattern.Proceed when the LSU is replaced.


71JUN 2004Ver. 2.0

UF-9000
DP-180/190
19 Move Mirror To Lock a) Press the Start key to move the mirror unit to the locked position for transporting the copier.

b) When the mirror unit is locked, the machine will not accept any numerical key input.

Note:The locking operation is automatically reset when the Power switch is turned ON again.

20-46 Not Used47 C47 ADF Scan Test Place the document on the ADF first.

Press START key to begin.48 C48 Book Scan Test Press START key to begin.

Press STOP key to finish.49-54 Not Used


72JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.1.8. F9 Mode: Unit Maintenance









F9 ModeService Mode Item Remarks

F9 Unit Maintenance

00 Fax Function Parameter01 Service Alert Tel # Displays the contact number when a

machine malfunction occurs.02 Firmware

Version00 SC Displays the firmware version for SC.01 SC Boot Displays the firmware version for SC

Boot.02 PNL Displays the firmware version for PNL.03 SPC (Scanner) Displays the firmware version for SPC.04 Printer Displays the firmware version.05 FAX Modem Displays the firmware version for FAX

Option 1.06 Not Used07 SC2 Displays the firmware version for Slot 1.

03 Print Device Info.

00 F5/F6 Parameters Prints the memory contents of the F5 and F6 modes.

01 Machine Information Prints the machine setup information list.02 Counter Information Prints the Counter information list.03 System Address

Info.Prints the system memory setting.

04 RAM Address Information

Prints the RAM data dump list.

04 RAM Edit Mode

1 Relative Address Setting of Relative address.2 Absolute Address Setting of Real address.

05 Serial Number Registration of Serial Number for Maintenance.Clears by Shipment Set.

73JUN 2004Ver. 2.0

UF-9000
DP-180/190
F9 Unit Maintenance

06 RAM Initialize

00 Parameter Initialize Resets the Fax and Function parameters to default values.

01 All Job Clear Clears all Jobs stored in Flash Memory.02 LBP Error Log Clear Clears LBP Error log03 Shipment Set Clears All Jobs, All Preset Data,

Parameter Initialize & Resets the Counters (Fax).

04 LBP Fuser Reset Clears the LBP fuser error.05 Dept. Counter Clear

07 FirmwareUpdate

00 Update FROM Card Updates the firmware in the machine with the Master Firmware Card.

01 Update from USB Updates the firmware in the machine with the USB.

08 ProgramBackup(Refer toSect. 2.5. of the Service Manual)

00 Main Onboard F-ROM 4MB01 Option 1 all Slot 1 FRM8 PCB 8MB02 Option 1 a Slot 1 FRM8 PCB 4MB (a)03 Option 1 b Slot 1 FRM8 PCB 4MB (b)04 Not Used Slot 2 FRM8 PCB 8MB05 Not Used Slot 2 FRM8 PCB 4MB (a)06 Not Used Slot 2 FRM8 PCB 4MB (b)

09 Update Prog. Card Creates a Master Firmware Card using the Firmware Update Kit. A 4MB or 8MB Flash Memory Card will be required depending upon the model.

10 ProgramCopy

00 From card to slot 1 Configuration for Program copy.01 From card to slot 202 From slot 1 to card03 From slot 1 to slot 204 From slot 2 to card05 From slot 2 to slot 1

11 Parameter Backup Backup the Parameter.12 Parameter Restore Restore the Parameter.13 Page Memory Size Displays the page memory size (MB).14 Sort Memory Size Displays the sort memory size (MB).

F9 ModeService Mode Item Remarks

74JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2. Service Modes (For Facsimile)4.2.1. Fax Service Mode Procedure

1. To entet the Fax Service Modea. Press “FAX/EMAIL” key.b. Press “FUNCTION” and then “7” keys.c. Press “MONITOR” four times, then press “*”.d. Enter the desired code number or press the “V”, ”/\” arrow keys.

2. To exit the Fax Service ModePress “STOP” key.

Note:The following buttons provide these functions in the Service Mode:

4.2.2. FAX Service Mode TableThe following service modes are provided to assist you in setting operational functions of the unit and determining the condition of the unit.

"START": : The new setting value is stored in the machine."V” : Scroll the function parameter number down."/\ “ : Scroll the function parameter number up.

Service Modes (For Facsimile)No. Service Mode Description00 Not Used01 Function Parameter Setting Allows changes to the function parameters (the home position,

etc.).02 RAM Edit Mode Factory use only.03 Print Parameter List / Report Prints the Function Parameter List, Page Memory Test, Printer

Report, All Document File, Protocol Trace and Toner Order Form.

04 Modem Tests Generates various binary, tonal and DTMF signals, by the modem.

05 Not Used06 RAM Initialize Initialize RAM and restore the default value of the function

parameters.Note: Turn the Power Switch to the OFF and back to the ON position to enable the parameter settings.

07 Not Used08 Check & Call Allows input of information for Service Alert Report,

Maintenance Alert Report and Toner Order Form.09 System Maintenance Used for Firmware Update, Firmware Backup, Parameter

Restore, Parameter Backup, Transferring Firmware from the PC to the Flash Card and Sending a Received File during a fatal printer error.

75JUN 2004Ver. 2.0

UF-9000
DP-180/190
10 Firmware Version

00 SC Displays the firmware version for SC.01 SC Boot Displays the firmware version for SC Boot.02 PNL Displays the firmware version for PNL.03 SPC (Scanner) Displays the firmware version for SPC.04 Not Used05 FAX Modem Displays the firmware version for FAX.06 Not Used07 SC2 Displays the firmware version for Slot 1.

Service Modes (For Facsimile)No. Service Mode Description

76JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.3. Fax Service Mode 1 (Function Parameter Setting)Use the following procedure to change the function parameters.

Enter the desired code number and press “START” key.↓

If you wish to select another code number, scroll the menu with the “V”, ”/\” arrow keys.↓

Select the desired function code and press the "START" key.↓


Press “STOP” key, then press “FUNCTION” and “CLEAR” keys simultaneously to exit the service mode.

Function Parameter TableNo. Parameter Selections Function000 Monitor/Tel Dial 1 = Monitor

2 = Tel/DialSelects whether the machine starts to TX automatically during On-Hook dialing.Monitor : Start to TX after pressing STARTTEL/DIAL : Start to TX automatically

001 Alarm Status 1 = Off2 = Timer3 = Constant

Selects the No Paper or No Toner alarm status.OFF : Alarm is disabled.Timer : Alarm will shut off after 6 seconds.Constant : Alarm will not stop until "STOP" is

pressed or the error is cleared/corrected.

002 Stop Comm. JRNL

1 = Off2 = On

Selects whether the machine prompts to print the COMM. Journal when the printout condition is set to INC and STOP is pressed during communication.

003 Continuous Poll 1 = Off2 = Stn (Tx only)3 = Hub (Rx only)

Selects whether the Continuous Polling feature is enabled.Stn : Place the document(s) on the ADF or Platen,

then press the assigned Program Key to store or add the documents into a polled file. (See Note 1)

Hub : When the polling command is initiated, the machine will continuously poll originals from the remote stations until it is interrupted by pressing "STOP".

004 Numeric ID Set 1 = Off (will not accept)2 = On (accepts)

Selects whether the machine accepts and allows to set or change the Numeric ID.

77JUN 2004Ver. 2.0

UF-9000
DP-180/190
005 Destination Code(DP-180/190 only)

000 : Austria001 : U.K.002 : Canada003 : Denmark004 : Taiwan005 : Finland006 : Germany007 : Netherlands008 : Italy009 : Spanish010 : Hong Kong011 : Australia012 : Switzerland013 : Norway015 : Portuguese016 : Ireland017 : Belgium018 : Sweden019 : Turkey020 : U.S.A.021 : France022 : New Zealand025 : Japan029 : Poland030 : Czech031 : Russia032 : Greece033 : Hungary034 : Indonesia035 : South Korea038 : Malaysia039 : China045 : Thailand048 : South Africa049 : Singapore050 : Universal051 : East Euro999 : Initialize

Specified destinations only.

006 ID Display 1 = Number (Numeric ID)2 = Chara (Character ID)

Selects the priority of displaying the ID.

007 JRNL Column 1 = Station2 = RCV’D ID

Selects the contents of the ID to display on the Journal.

008 Monitor 1 = Off2 = On

Selects whether the Monitor is ON/OFF for monitoring fax signals.(FOR SERVICE USE ONLY)

009 DC Loop 1 = Off (Normal)2 = On (Off Hook)

Selects a false Off Hook state for back to back communication test.

010 TX Level 00 = 0 dBm~15 = -15 dBm

Selects the TX signal output level, 0 to -15 dBm in 1 dBm steps.

Function Parameter TableNo. Parameter Selections Function

78JUN 2004Ver. 2.0

UF-9000
DP-180/190
011 RX Level 1 = -43 dBm2 = -38 dBm3 = -33 dBm4 = -48 dBm

Selects the receiving sensitivity of -33/-38/-43/-48 dBm.

012 DTMF Level 00 = 0 dBm~15 = -15 dBm

Selects the DTMF output level, 0 to -15 dBm in 1 dBm steps.

013 G3 RX EQL 1 = 0dB2 = 4dB3 = 8dB4 = 12dB

Selects the cable equalizer for G3 reception mode, 0dB, 4dB, 8dB or 12dB.

014 G3 TX EQL 1 = 0dB2 = 4dB3 = 8dB4 = 12dB

Selects the cable equalizer for G3 transmission mode, 0dB, 4dB, 8dB or 12dB.

015 ~ 016

Not Used

017 TX Start 2400 bps4800 bps7200 bps9600 bpsTC7200 bpsTC9600 bps12000 bps14400 bps

Selects the transmission modem start speed, 14400/12000/TC9600/TC7200/9600/7200/4800/2400 bps.

Press “V” or “/\ “ to select the symbol rate.Note:

This parameter is applicable only when communicating with regular G3 machines. When communicating with Super G3 (V.34) machines, use Parameter No. 32.

018 RX Start 2400 bps4800 bps7200 bps9600 bpsTC7200 bpsTC9600 bps12000 bps14400 bps

Selects the reception modem start speed, 14400/12000/TC9600/TC7200/9600/7200/4800/2400 bps.

Press “V” or “/\ “ to select the symbol rate.Note:

This parameter is applicable only when communicating with regular G3 machines. When communicating with Super G3 (V.34) machines, use Parameter No. 33.

019 ITU-T V.34 1 = Off2 = On3 = Select

Selects whether the ITU-T V.34 is Off, On or Select.Select: Select whether the ITU-T V.34 is Off or On,

when entering Phone Book Dialing Numbers or Manual Number Dialing.

020 ITU-T ECM 1 = Off (Invalid)2 = On (Valid)

Select the ECM mode.

021 EP Tone 1 = Off (without EP Tone)2 = On (with EP Tone)

Selects whether to add the echo protect tone on V.29 mode.(Used when Echo Suppression is disabled.)On : AddOff : Do not add

022 Signal Interval 1 = 100 ms2 = 200 ms3 = 500 ms

Selects the time interval between the receiving signal and the transmitting signal.

023 TCF Check 1 = Normal (Short)2 = Long

Selects the TCF check interval Long/Short

024 CED Frequency 1 = 1080 Hz (non ITU-T)2 = 2100 Hz

Selects the CED frequency 2100/1080 Hz


79JUN 2004Ver. 2.0

UF-9000
DP-180/190
025 COMM. Start-Up 1 = First2 = Second

Selects the communication start-up condition (XMT and Polling).(Used when Echo Suppression is disabled.)

026 Non-Standard 1 = Off (Invalid)2 = On (Valid)

Selects own mode (Panafax mode).

027 Short Protocol B 1 = Off (Invalid)2 = On (Valid)

Selects the short protocol mode.

028 Short Protocol D 1 = Off (Invalid)2 = On (Valid)

Selects the short protocol mode. When activated, it allows the machine to automatically store the modem speed for each Auto Dial Number.

029 Remote Diagnostics

1 = Off (will not accept)2 = On (accepts)

Selects whether the machine accepts Remote Diagnostics from the service station.

030 CED & 300 bps 1 = 75 ms2 = 1 sec

Selects the pause interval between the CED and the 300 bps signal. (Used when Echo Suppression is disabled.)

031 RTC = EOL x 12 1 = Off (EOLx6)2 = On (EOLx12)

Selects the RTC signal, EOLx6 or EOLx12.

032 V34 TX Start 2400-33600bps Selects the transmission modem start speed for V.34 communication, 33600-2400 bps.

Press “V” or “/\ “ to select the symbol rate.033 V34 RX Start 2400-33600bps Selects the receiving modem start speed for V.34

communication, 33600-2400 bps.Press “V” or “/\ “ to select the symbol rate.

034 V34 TX SR 2400-3429sr Selects the transmission symbol rate for V.34, 3429/ 3200/3000/2800/2400 sr.

Press “V” or “/\ “ to select the symbol rate.035 V34 RX SR 2400-3429sr Selects receiving symbol rate for V.34, 3429/3200/

3000/2800/2400 sr.Press “V” or “/\ “ to select the symbol rate.

036 Not Used037 Protocol Display 1 = Off (not displayed)

2 = On (displayed)Selects whether to display the modem speed during communication. (Press the Job Status Key to display)

038 Not Used039 Flash Time 5 = 50 ms

~100 = 1000 ms

Selects the pause interval before activating the Flash key.

040 Flash Time (PSTN)

5 = 50 ms~100 = 1000 ms

Selects the pause interval before activating the Flash key.(For Germany, Austria and Czech)

041 Pause Time 1 = 1 sec.~10 = 10 sec.

Selects the pause interval from 1 sec. ~ 10 sec. for dialing through a switchboard or for international calls.

042 Not Used043 Redial Interval 0 = no waiting

~15 = 15 minutes

Selects the redial interval from 0 to 15 minutes in 1 minute steps.


80JUN 2004Ver. 2.0

UF-9000
DP-180/190
044 Redial Count 0 = no redial~15 = 15 times

0 ~ 9 (For Australia Only)

Selects the redial count from 0 to 15 times in 1 step intervals.Note:

In order to comply with the requirements TBR21 in the EC countries, do not select 15 times.

045 Ring Detect Count

1 = 1 ring~9 = 9 rings

Selects the ring detection count from 1 to 9 rings in 1 ring step intervals.

046 On-Hook Time 0 = 0 sec.~90 = 90 sec.

Selects the on-hook time between sequential communication calls in 1 second step intervals.

047 Response Wait Interval

1 = 1 sec.~90 = 90 sec.

20 ~ 150 sec. (For France Only)

Selects the waiting interval for the response after completing the dialing.

048~ 049

Not Used

050 Ring Detect Mode 1 = Normal2 = Rough

Selects the quality of ringer detection. Use if the line signal is out of regulation, set to "Rough" so that the unit may detect the ringing signals.

051 Not Used052 Pulse Rate 1 = 10 pps

2 = 20 ppsSelects the dial pulse rate 10/20 pps.

053~ 054

Not Used

055 Busy Tone Check 1 = Off2 = On

Selects whether to detect the Busy Tone.

056 Dial Tone Check(Specified destinations only)

1 = Off2 = On

Selects whether to detect Dial Tone before dialing the telephone number.

057 DC Loop Check(Specified destinations only)

1 = Off2 = On

Selects whether the unit checks the DC Loop during communication.

058 Comm. JRNL + Image

1 = Off (without image)2 = On (with image)

Selects whether the machine prints the COMM. Journal with image.

059 Confidential RCV Report

1 = Off (does not print out)2 = On (prints out)

Selects whether the machine prints the Confidential RCV Report.

060 Version Indicates the Host software version.

061 TX/RX/PRT/CPY TX:****** PRT:******RX:****** CPY:******

Displays the transmitted, received, total printed and copied document count.

062 Print Counter 1 = Off2 = On

Selects whether to print in the Fax Parameter List, the counter information that is displayed in the Function Parameter No. 61.

063~ 067

Not Used


81JUN 2004Ver. 2.0

UF-9000
DP-180/190
068 NYSE Fax Forward(USA and Canada Only)

1 = Off2 = On

Selects whether the machine will forward the incoming and outgoing faxes to a specified station.Note:

Once this parameter is activated, Fax Forwarding via Fax Parameter 054 is automatically disabled, an Access Code of "0000" is automatically assigned and Fax Parameter 038 has a new setting added called "NYSE".

069 NYSE Local Print(USA and Canada Only)

1 = Inc2 = On (Always)

Selects the printing condition for the incoming faxes after FAX Forwarding.INC. : Prints only if FAX Forwarding fails.ON : Always prints.

070 Line Error 128 lines256 lines512 lines1024 line2048 linesOff(will not disconnect line)

1. Selects the line disconnect condition during reception. If the number of line errors exceed this setting, the unit will disconnect the line.

Press “V” or “/\ “ to select the symbol rate.2. Selects the transmit condition of RTP/PIP or

RTN/PIN. (Available if No.73 Error Detect is set to "LINES") (See Note 1)

071 Total Error 1 = 5%2 = 10%3 = 15%4 = 20%

Selects the transmit condition of RTP/PIP or RTN/PIN.(Available if No.73 Error Detect is set to "RATE".)(See Note 2)

072 Continuous Error 1 = Off (unlimited)2 = 3 lines/STD3 = 6 lines/STD4 = 12 lines/STD

Selects the continuous total error criteria of Off/3/6 or 12 lines in Standard mode. If continuous total error exceeds this setting, the unit will transmit RTN/PIN. (Available if No.73 Error Detect is set to "RATE".)

073 Error Detect 1 = Lines2 = Rate

Selects the error detect condition Lines/Rate.

074 RTN Receive 1 = Disconnect2 = Continue

Selects whether to disconnect the phone line or continue when "RTN" is received.

075 Coding 1 = MH (MH only)2 = MR (MH or MR)3 = MMR (MH or MR or MMR)4 = JBIG

Selects the coding scheme.

076 Batch TX(USA and Canada Only)

1 = Off2 = On

Selects whether the batch transmission is available.

077 RX JAM Length 1 = Off (unlimited)2 = 2 m

Selects the maximum length of a received document that can be printed.

078~ 079

Not Used

080 Doc Top Feed -99~+99

Adjusts the distance between the scanning sensor ON position and the scanning start position.

081 Doc End Feed -90~+127

Adjusts the distance between the scanning sensor OFF position and the scanning end position.


82JUN 2004Ver. 2.0

UF-9000
DP-180/190
082 JAM Length 1 = 1 m2 = 2 m

Selects the maximum length of the original that can be scanned.

083 Not Used084 Line As No Paper 1 = Ring (ring)

2 = Busy (keep line busy)Selects whether to ring or send a busy tone to the remote station when the recording paper runs out or the unit cannot receive because of any trouble.

085~086

Not Used

087 Darker Level 0 = Lightest Contrast~15 = Darkest Contrast

Selects the contrast level.0← →15Lightest← →Darkest

088 Normal Level089 Lighter Level

090~ 091

Not Used

092 Smoothing 1 = Off2 = On

Selects whether the smoothing function is available.

093 ~ 094

Not Used

095 Reduction Ratio (70-100) Selects Print Reduction Ratio(%).096 ~ 101

Not Used

102 Book Top Feed -30~+30

Adjustment of original registration detection timing.

103 Book End Feed -9~0

Adjustment of trail edge void.

104~109

Not Used

110 MAC Address Indicates the MAC Address.111 Not Used112 Insert EMAIL TXT 1 = Off

2 = OnSelects whether the Text Template (email message) is programmable and added on all email sent in the message body above the top line of text. (Up to 40 characters Programmed in the User Parameters.)Note:

After enabling this feature, aside from entering the text in the User Parameters, it also has to be activated in each Auto Dial Number before it will take effect. It does not work for Direct Dialed Numbers.

113~114

Not Used

115 Time Zone 1 = Scroll2 = Direct

Selects the setting method for Time Zone.Scroll : Allows using "Scroll Keys" to scroll

through the Time Zone Table.Direct : Allows you to input the Time Zone

directly, (*) key to be used as a switch between +/-.

116 Overwrite Warning

1 = Yes2 = No

Selects whether the Overwrite Warning is included on the Internet FAX Result Receipt when programming the Auto Dialer via email.


83JUN 2004Ver. 2.0

UF-9000
DP-180/190
Note 1: Continuous Polling (Station Mode)This feature allows you to store or add documents into a polled file in memory.

To enable the Continuous Polling feature set Function Parameter No. 003 to "2:Station". The last Program Key will be assigned with the “Store 4 Poll” Key name automatically and cannot be changed.

To prepare the document(s) to be polled, simply place the document(s) on the ADF or Platen and then press the Program Key to store or add the document(s) into a polled file.

(Note: If a regular polled file is stored in memory, the Program Key for Continuous Polling will not be accepted.)

Note 2: Function Parameter No. 070 (Line Error)-Transmit condition of RTP/PIP or RTN/PIN

Note 3: Function Parameter No. 071 (Total Error)-Transmit condition of RTP/PIP or RTN/PIN

Note 4: The default setting of parameters depends on the country’s specifications or regulations. Print the Function Parameter List to confirm the default settings.

117~121

Not Used

122 LDAP 1 = Off2 = On

When LDAP is used, specialized characters may be displayed as different characters.

123 ~ 199

Not Used

SignalSetting

1:128 2:256 3:512 4:1024 5:2048 6:OffMCF/PIP 0-31 0-63 0-127 0-255 0-511 AlwaysRTP/PIP 32-63 64-127 128-255 256-511 512-1023 -RTN/PIN 64-127 128-255 256-511 512-1023 1024-2047 -

SignalSetting

1:5% 2:10% 3:15% 4:20%MCF/PIP 0-2 0-4 0-7 0-9RTP/PIP 3-4 5-9 8-14 10-19RTN/PIN 5- 10- 15- 20-


84JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.4. Fax Service Mode 3 (Printout of Lists, Reports and Test Results) From this Service Mode you can print the Function Parameter List, Page Memory Test, Printer Report, All Document File, Protocol Trace and the Toner Order Form.

4.2.4.1. Function Parameter ListA list of all Function Parameters can be printed by the following procedure.

Press the “V”, ”/\” arrow keys to select the "3: Print Report/List" on the display.↓

Press the “SET” key.↓

Press the “SET” key to select the "1:Function Parameter List".↓

Press the “STOP” key twice to exit the service mode.

85JUN 2004Ver. 2.0

UF-9000
DP-180/190
Note:1. The contents of the Function Parameter List may vary depending on the country’s regulations.2. “ * ” mark will be shown on the left side of number when setting was changed from default.

Function Parameter List (Sample)

************* -FUNCTION PARAMETER- ************* DATE MMM-dd-yyyy ***** TIME 12:07 ***P.01

-PANASONIC -

Note: The power must be reset for the new parameter settings to take effect.

***** ******************* -PANASONIC - ****** -12345678901234567890- *********

000 Mon/Tel Dial:[Monitor] Monitor 050 Ring Det Mode:[Normal] Normal001 Alarm Status:[Timer] Timer 051 ----------002 Stop Comm. JRNL:[On] On 052 Pulse Rate:[10pps] 10pps003 Continuous Polling:[Off] Off 053 ----------004 Numeric ID Set:[On] On 054 ----------005 Destination Code:[999] 999 055 Busy Tone Check:[On] On006 ID Display:[Chara] Chara 056 ----------007 JRNL Column:[Station] Station 057 ----------008 Monitor:[Off] Off 058 Comm.JRNL +Image:[On] On009 DC Loop:[Off] Off 059 Conf.RCV Report:[On] On

010 TX Level:[-11dBm] -11dBm 060 Version: UF-9000 AAV......011 RX Level:[-43dBm] -43dBm 061 TX/RX/PRT/CPY: 000080/000168/000003/000000012 DTMF Level:[-5dBm] -5dBm 062 Print Counter:[Off] Off013 G3 RX EQL:[0dB] 0dB 063 ----------014 G3 TX EQL:[0dB] 0dB 064 ----------015 --------- 065 ----------016 --------- 066 ----------017 TX Start:[14400bps] 14400bps 067 ----------018 RX Start:[14400bps] 14400bps 068 NYSE Fax Forward:[Off] Off019 ITU-T V.34:[On] On 069 NYSE Local Print:[inc] inc

020 ITU-T ECM:[On] On 070 Line Error:[128] 128021 EP Tone:[Off] Off 071 Total Error:[10] 10022 Sig. Interval:[500ms] 500ms 072 Conti. Error:[Off] Off023 TCF Check:[Normal] Normal 073 Error Detect:[Rate] Rate 024 CED Freq.:[2100Hz] 2100Hz 074 RTN Receive:[Discon] Discon025 Comm. Start-Up:[1'st] 1'st 075 Coding:[JBIG] JBIG026 Non-Standard:[On] On 076 Batch TX:[On] On027 Short Protocol B:[On] On 077 RX JAM Length:[2 m] 2 m028 Short Protocol D:[On] On 078 ----------029 Remote Diag.:[On] On 079 ----------

030 CED & 300bps:[75ms] 75ms 080 Doc Top Feed:[0] 0031 RTC=EQL x 12:[Off] Off 081 Doc End Feed:[0] 0032 V34TX Start:[33600bps] 33600bps 082 JAM Length:[2 m] 2 m033 V34RX Start:[33600bps] 33600bps 083 ----------034 V34 TX SR:[3429sr] 3429sr 084 Line As Nopaper:[Ring] Ring035 V34 RX SR:[3429sr] 3429sr 085 ----------036 --------- 086 ----------037 Protocol Display:[Off] Off 087 Darker Level:[2] 2038 --------- 088 Normal Level:[8] 8039 Flash Time:[500ms] 500ms 089 Lighter Level:[14] 14

040 --------- 090 ----------041 Pause Time:[3sec] 3sec 091 ----------042 --------- 092 Smoothing:[On] On043 Redial Interval:[3min] 3min 093 ----------044 Redial Count:[5] 5 094 ----------045 Ring Det. Count:[2] 2 095 Reduction Ratio:[100%] 100%046 On-Hook Time:[5sec] 5sec 096 ----------047 Response Wait:[5sec] 55sec 097 ----------048 --------- 098 ----------049 --------- 099 ----------

86JUN 2004Ver. 2.0

UF-9000
DP-180/190
Note:1. The contents of the Function Parameter List may vary depending on the country’s regulations.2. “ * ” mark will be shown on the left side of number when setting was changed from default.

Function Parameter List (Sample)

************* -FUNCTION PARAMETER- ************* DATE MMM-dd-yyyy ***** TIME 12:07 ***P.02

-PANASONIC -

***** ****************** -PANASONIC - ****** -12345678901234567890- ***********

100 ---------- 150 ----------101 ---------- 151 ----------102 Book Top Feed:[0] 0 152 ----------103 Book End Feed:[0] 0 153 ----------104 ---------- 154 ----------105 ---------- 155 ----------106 ---------- 156 ----------107 ---------- 157 ----------108 ---------- 158 ----------109 ---------- 159 ----------

110 MAC Address: 080023000177 160 ----------111 ---------- 161 ----------112 Insert EMAIL TXT:[Off] Off 162 ----------113 ---------- 163 ----------114 Symbol set:[Std] Std 164 ----------115 Time Zone:[Direct] Direct 165 ----------116 Overwrite Warning:[Yes] Yes 166 ----------117 ---------- 167 ----------118 ---------- 168 ----------119 ---------- 169 ----------

120 ---------- 170 ----------121 ---------- 171 ----------122 LDAP:[On] On 172 ----------123 ---------- 173 ---------- 124 ---------- 174 ----------125 ---------- 175 ----------126 ---------- 176 ----------127 ---------- 177 ----------128 ---------- 178 ----------129 ---------- 179 ----------

130 ---------- 180 ----------131 ---------- 181 ----------132 ---------- 182 ----------133 ---------- 183 ----------134 ---------- 184 ----------135 ---------- 185 ----------136 ---------- 186 ----------137 ---------- 187 ----------138 ---------- 188 ----------139 ---------- 189 ----------

140 ---------- 190 ----------141 ---------- 191 ----------142 ---------- 192 ----------143 ---------- 193 ----------144 ---------- 194 ----------145 ---------- 195 ----------146 ---------- 196 ----------147 ---------- 197 ----------148 ---------- 198 ----------149 ---------- 199 ----------

Note: The power must be reset for the new parameter settings to take effect.

87JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.4.2. Page Memory TestA test pattern prints out for checking the page memory and printer mechanism using the following procedure.



Press the “V”, ”/\” arrow keys to select the "3: Page Memory Test".↓



SC : TX/RX/PRT/CPY : 000123/000456/000789/000666SC BOOT : MEMORY SIZE : (2 MB)PNL : MAC ADDRESS : 08002300E078PRINTER : SHIPMENT SETSPC(SCANNER) :FAX MODEM :SC2 :

************* TEST PATTERN PRINT **************** DATE MMM-dd-yyyy ***** TIME 12:07 ***P.01

-PANASONIC -

***** ****************** -PANASONIC - ****** -12345678901234567890- ***********

88JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.4.3. Printer ReportAll printer errors are logged on the Printer Report which can be printed by the following procedure.



Press the “V”, ”/\” arrow keys to select the "4: Printer Report".↓



**************-PRINTER REPORT-********************* DATE MMM-dd-yyyy ***** TIME 19:02********

LAST PRINT ERROR : MMM-dd-yyyy 15:38 J00 00-00000016

SERIAL NUMBER : CUSTOMER ID : 1234567890123456

PRINTER :

TRANSMIT COUNTER : 000475 RECEIVE COUNTER : 000398 COPY COUNTER : 000083 PRINT COUNTER : 000016

01.MMM-dd-yyyy 15:38 J00 00-00000016 02.MMM-dd-yyyy 10:48 J02 00-00000016

SC : PNL : SPC (SCANNER) :

-PANASONIC -

***** *******************-PANAFAX -*******-12345678901234567890-**************

FIRMWARE VERSION

NO.DATE & TIME ERROR CODE RRROR COUNT NO.DATE & TIME ERROR CODE RRROR COUNT --------------------------------------------------------------------------------------------

--------------------------------------------------------------------------------------------

|

||

89JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.4.4. All Document FilesPrint the document files from the Flash Memory.



Press the “V”, ”/\” arrow keys to select the "5: All Document Files".↓



90JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.4.5. Protocol TracePrint a Protocol Trace Report for the previous communication.



Press the “V”, ”/\” arrow keys select the "6: Protocol Trace".↓



*************** PROTOCOL LOG. REPORT ****************** DATE MMM-dd-yyyy ***** TIME 16:56 *******

STATUS : OK MODE : ECM-TX (STANDARD) SPEED : 9600bps 0MS/L REMOTE CAPA. : DIS 00 CE B9 C4 80 12 LOCAL CAPA. : TSI 2B 20 20 20 38 37 2B 2B 2B 2B 39 38 36 36 35 34 37 38 38 30 DCS 00 C6 F8 44

REMOTE : NSF CSI DIS CFR COMMAND LOG.

LOCAL : TSI DCS PIX PPS-EOP

REMOTE : MCF LOCAL : DCN

-PANASONIC -

****************************-PANASONIC -*************-12345678901234567890-***************

------------------------------------------------------------------

91JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.4.6. Toner Order FormThe Toner Order Form can be printed out manually by the following procedure.



Press the “V”, ”/\” arrow keys to select the "7: Toner Order Form".↓



92JUN 2004Ver. 2.0

UF-9000
DP-180/190
Explanation of Contents

(1) Low Toner Message (Fixed) “The toner supply in your machine is running low”(2) Dealer Name Up to 25 digits(3) Toner Order Tel # Up to 36 digits(4) Toner Order Fax # Up to 36 digits(5) Customer ID Up to 16 characters (User Identification Code)(6) Toner Cartridge No. Refer to the Supply list

************************************* > TONER CARTRIDGE ORDER FORM < *************************************

**** The toner supply in your machine is running low **** (1)

To order a replacement Cartridge from your Authorized Dealer

Panasonic Corp. (2)

by Phone: 1 201 111 5555 (3)by Fax: 1 201 111 4444 (4)

Thank you for your order.

Customer Name and Address=========================

Ship to: Bill to:

Attention: Attention:

Phone No.: Phone No.:

Customer ID: ABC COMPANY (5) P.O. No.(if required):

Toner Cartridge No.: (6) Serial No.:

Quantity Required:

/ /Print your name and title Signature & Date

93JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.5. Fax Service Mode 4 (Modem Test)4.2.5.1. Binary SignalThis Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure.

Press the “V”, ”/\” arrow keys to select the "4: MODEM Test" on the display.↓

Press the “SET” key to select the "1: Signal Test".↓


Press the desired number. ↓



Binary Signal Table

Number Signals1 V21 300bps2 V27ter 2400bps3 V27ter 4800bps4 V29 7200bps5 V29 9600bps6 V17 TC7200bps7 V17 TC9600bps8 V17 12000bps9 V17 14400bps

94JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.5.2. Tonal SignalThis Service Mode is used to check the tonal signal output. Signals can be output to the line using the following procedure.


Press the “SET” key to select the "2: Tonal Testl".↓


Press the desired number and press the "START" key.↓


Tonal Signal Table

Number Signals1 462 Hz2 1080 Hz3 1100 Hz4 1300 Hz5 1650 Hz6 1850 Hz7 2100 Hz

95JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.5.3. DTMF SignalThis Service Mode is used to check the DTMF (Dual Tone Multi Frequency) signal output.The DTMF signal can be generated using the following procedure.

• DTMF Single TonePress the “V”, ”/\” arrow keys to select the "4: MODEM Test" on the display.

↓Press the “SET” key to select the "3: DTMF Test".

↓Press the “SET” key.

↓Press the “V”, ”/\” arrow keys to select the "1. Single".

↓Press the desired number and press the "START" key.

↓Press the “STOP” key twice to exit the service mode.

• DTMF Dual TonePress the “V”, ”/\” arrow keys to select the "4: MODEM Test" on the display.

↓Press the “SET” key to select the "3: DTMF Test".

↓Press the “SET” key.

↓Press the “V”, ”/\” arrow keys to select the "2. Dual".

↓Press the desired number and press the "START" key.


DTMF Single Tone Table DTMF Dual Tone Table

Number DTMF Signal Tones Number DTMF Dual Tones1 697 Hz 0 941 Hz + 1336 Hz2 770 Hz 1 697 Hz + 1209 Hz3 852 Hz 2 697 Hz + 1336 Hz4 941 Hz 3 697 Hz + 1477 Hz5 1209 Hz 4 770 Hz + 1209 Hz6 1336 Hz 5 770 Hz + 1336 Hz7 1477 Hz 6 770 Hz + 1477 Hz8 1633 Hz 7 852 Hz + 1209 Hz

8 852 Hz + 1336 Hz9 852 Hz + 1477 Hz* 941 Hz + 1209 Hz# 941 Hz + 1477 Hz

96JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.5.4. Binary Signal (V.34)This Service Mode is used to check the binary signal output. Signals can be output to the line using the following procedure. (V.34)


Press the “SET” key to select the "4: V34 MODEM".↓


Press the desired number and press the "START" key.↓


Binary Signal Table

Number Signals Number Signals Number Signals01 V34 2400 sr 2400 bps 22 V34 3000 sr 9600 bps 43 V34 3429 sr 4800 bps02 V34 2400 sr 4800 bps 23 V34 3000 sr 12000 bps 44 V34 3429 sr 7200 bps03 V34 2400 sr 7200 bps 24 V34 3000 sr 14400 bps 45 V34 3429 sr 9600 bps04 V34 2400 sr 9600 bps 25 V34 3000 sr 16800 bps 46 V34 3429 sr 12000 bps05 V34 2400 sr 12000 bps 26 V34 3000 sr 19200 bps 47 V34 3000 sr 19200 bps06 V34 2400 sr 14400 bps 27 V34 3000 sr 21600 bps 48 V34 3429 sr 16800 bps07 V34 2400 sr 16800 bps 28 V34 3000 sr 24000 bps 49 V34 3429 sr 19200 bps08 V34 2400 sr 19200 bps 29 V34 3000 sr 26400 bps 50 V34 3429 sr 21600 bps09 V34 2400 sr 21600 bps 30 V34 3000 sr 28800 bps 51 V34 3429 sr 24000 bps10 V34 2800 sr 4800 bps 31 V34 3200 sr 4800 bps 52 V34 3429 sr 26400 bps11 V34 2800 sr 7200 bps 32 V34 3200 sr 7200 bps 53 V34 3429 sr 28800 bps12 V34 2800 sr 9600 bps 33 V34 3200 sr 9600 bps 54 V34 3429 sr 31200 bps13 V34 2800 sr 12000 bps 34 V34 3200 sr 12000 bps 55 V34 3429 sr 33600 bps14 V34 2800 sr 14400 bps 35 V34 3200 sr 14400 bps 56 ANSam15 V34 2800 sr 16800 bps 36 V34 3200 sr 16800 bps 57 CM16 V34 2800 sr 19200 bps 37 V34 3200 sr 19200 bps 58 JM17 V34 2800 sr 21600 bps 38 V34 3200 sr 21600 bps 59 INFO0c & TONEB18 V34 2800 sr 24000 bps 39 V34 3200 sr 24000 bps 60 INFO0c & TONEA19 V34 2800 sr 26400 bps 40 V34 3200 sr 26400 bps 61 PPh & AC & ALT20 V34 3000 sr 4800 bps 41 V34 3200 sr 28800 bps21 V34 3000 sr 7200 bps 42 V34 3200 sr 31200 bps

97JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.6. Fax Service Mode 6 (RAM Initialization)Initializes RAM and restores the Function Parameters to their default values.Note:

This operation should be performed when the unit is first installed.

Press the “V”, ”/\” arrow keys to select the "6: RAM initialize" on the display.↓

Press the “SET” key to select the desired Mode number.↓

Press the "SET" key to initialize RAM.↓


RAM Initialization Table

No. Initialize Mode Description01 PARAMETER INITIALIZE Restores the Fax and Function Parameters to default

values.Note: Turn the Power Switch to the OFF and back to the ON position to enable the parameter settings.

02 JOURNAL CLEAR Clears the Journal contents.03 AUTO DIAL CLEAR Clears the One-touch, ABBR Numbers and Phone Books.04 PROGRAM DIAL CLEAR Clears the Program keys.05 LOGO/ID/PSWD CLEAR Clears the Logo, ID, Polling Password.06 LBP ERROR LOG CLEAR Clears the Printer Error Log.07 SHIPMENT SET Deletes all setting information, except parameter number

80 and 81, then set default values.08 FLASH MEMORY CLEAR Deletes all information in the Flash Memory.09 ALL JOB CLEAR Clears all Jobs stored in Flash Memory.

98JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.7. FAX Service Mode 8 (Check & Call)4.2.7.1. OverviewThis feature enables the Authorized Servicing Dealers to manage and improve the machine maintenance to their customers by alerting them of equipment problems. It also can be used as a Supply Sales Tool by alerting the Dealer that the unit is running Low on Toner. The function overview is as follows:

1. The machine’s printer error information is stored in the Printer Report.2. The printer report can be manually printed when required.3. When printer errors occurs, the unit can automatically transmit the Service Alert Report to the pre-

registered telephone number or email address.4. When the unit detects Low Toner or PM counter reached the maintenance timing, it can automatically

transmit the Maintenance Alert Report to the pre-registered telephone number or email address.

Press the “V”, ”/\” arrow keys to select the "08 Check & Call" on the display.↓

Press the “SET” key to select the desired code number.(i.e. 01 Service Alert Fax #, input the telephone No. or for an email address, press the "FAX/EMAIL" Mode key and input the email address.)

↓Press the "SET" key.


4.2.7.2. Printer Reports• Conditions under which a report can be printed or transmitted1. Manual print

The Printer Report can be printed by Service Mode 3. (See Sect. 4.2.4.3.)2. Automatic transmission/printout

a. Service Alert ReportWhen the unit detects an Emergency Printer Error, the unit will immediately transmit the Service Alert Report to the pre-registered telephone number or email address. However, the unit will not transmit the Service Alert Report if it finds the same error within the same date in the error log.

b. Maintenance Alert ReportWhen the unit detects Low Toner, the unit can automatically transmit the Maintenance Alert Report to the pre-registered telephone number or email address. Refer to the Error Code Table.

c. Toner Order FormWhen the unit detects Low Toner, the unit can automatically print the Toner Order Form with the pre-registered order information.

d. Call Counter ReportWhen the printer counter reaches the pre-set number, the unit can automatically transmit the Call Counter Report to the pre-registered telephone number or email address.

Note:The Service and Maintenance Alert Reports are managed in the same manner as the normal memory transmission (Retry, Incomplete, File List, Display while it is transmitting, Journal).

99JUN 2004Ver. 2.0

UF-9000
DP-180/190
Note:TX (Transmission) Report: S = Service Alert Report, M = Maintenance Alert Report

Error Code Log Tx

Report Remarks

Ex-xx O S Refer to the Mechanical Error Code (E Code) Table. (Sect. 3.1.3.)E13 Out of Toner.Jxx Refer to the Jam Error Code (J Code) Table. (Sect. 3.1.2.)Uxx Refer to the User Error Code (U Code) Table. (Sect. 3.1.1.)U13 M Low Toner.

100JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.7.3. SERVICE ALERT REPORT FORMAT


(1) Customer ID(2) Firmware Version(3) Counter Information(4) Print Error Last 30 records (Latest on top)

*************************************************** DATE MMM-dd-yyyy ***** TIME 03:47 ********

**************************** > SERVICE ALERT REPORT < ****************************

(1)

(2)

CUSTOMER ID : ABC COMPANY

LAST PRINT ERROR : MMM-dd-yyyy 20:07 E04-01 00-00000013

FIRMWARE VERSION

(3)

(4)

COUNTER INFORMATION: CURRENT PM CYCLE CURRENT

F7-02 Total Count : 13 240000 2-Sided Count : 0PM COUNT : 13 (------) A4/LETTER Count : 3Scanner PM Count : 9 (------) A4-R/LETTER-R Count : 10ADF Count : 1 ------ OPC Drum Count : 13 ------ Process Unit Count : 13 (------)ADF PM Count : 1 F7-04 ADF Count : 1

ADF Read Count : 1Developer Count : 13 Scanner Count : 9Corona Cleaning Count : 13 Scanner Read Count : 9Avg. Print/Drum Rise Up : 1.00Total OPC Rotation Time : 0.03 F7-05 Copy Print Count : 3Avg. Sec/Drum Rise Up : 0.01 Copy Scan Count : 4

F7-03 Sheet Bypass Count : 0 F7-06 PC Print Count : 01st Paper Tray Count : 3 PC Scan Count : 62nd Paper Tray Count : 10

F7-07 FAX Transmit Count : 0 FAX Receive Count : 0

FAX Print Count : 0

PRINT ERROR:

NO. DATE & TIME ERROR CODE ERROR COUNT | NO. DATE & TIME ERROR CODE ERROR COUNT-------------------------------------------------------------------------------------------01 MMM-dd-yyyy 20:07 E04-01 00-00000013 |02 MMM-dd-yyyy 20:04 E04-01 00-00000013 | | | | | | | | | | | |

| -------------------------------------------------------------------------------------------

-LOGO PANASONIC -

***** *********************** -CHARACTER ID - ***** -31415926535897932384-*********

SC : SPC :

101JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.7.4. MAINTENANCE ALERT REPORT FORMAT


(1) Low Toner Message (Fixed) “MACHINE IS RUNNING OUT OF TONER”(2) Customer ID Up to 16 characters (User Identification Code)(3) Firmware Version(4) Transmission / Reception / Copy / Print Counters


**************************** > MAINTENANCE ALERT REPORT < ****************************

LAST PRINT ERROR : MACHINE IS RUNNING OUT OF TONER (1)

CUSTOMER ID : ABC COMPANY (2)

FIRMWARE VERSION (3)

(4) TRANSMIT COUNTER : 000244 RECEIVE COUNTER : 000082 COPY COUNTER : 000000 PRINT COUNTER : 000000

-LOGO PANASONIC -

************************************ -CHARACTER ID - ***** -31415926535897932384-***********

SC : SPC :

NO.DATE & TIME ERROR CODE ERROR COUNT NO.DATE & TIME ERROR CODE ERROR COUNT---------------------------------------------------------------------------------------------

---------------------------------------------------------------------------------------------

102JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.7.5. Toner Order Form


(1) Low Toner Message (Fixed) “The toner supply in your machine is running low”(2) Dealer Name Up to 25 digits(3) Toner Order Tel # Up to 36 digits(4) Toner Order Fax # Up to 36 digits(5) Customer ID Up to 16 characters (User Identification Code)(6) Toner Cartridge No. Refer to the Supply list

************************************* > TONER CARTRIDGE ORDER FORM < *************************************

**** The toner supply in your machine is running low **** (1)

To order a replacement Cartridge from your Authorized Dealer

Panasonic Corp. (2)

by Phone: 1 201 111 5555 (3)by Fax: 1 201 111 4444 (4)

Thank you for your order.

Customer Name and Address=========================

Ship to: Bill to:

Attention: Attention:

Phone No.: Phone No.:

Customer ID: ABC COMPANY (5) P.O. No.(if required):

Toner Cartridge No.: (6) Serial No.:

Quantity Required:

/ /Print your name and title Signature & Date

103JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.7.6. CALL COUNTER REPORT


(1) Customer ID(2) Firmware Version(3) Counter Information(4) Call Counter Pre-Set Value


***************************************************************** > SCHEDULED REPORT - CALL COUNTER HAS REACHED PRE-SET VALUE < *****************************************************************

(1)

(2)

CUSTOMER ID : ABC COMPANY

LAST PRINT ERROR : MMM-dd-yyyy 20:07 E04-01 00-00000013

FIRMWARE VERSION

(3)

(4)

COUNTER INFORMATION: CURRENT PM CYCLE CURRENT

PM COUNT : 13 (------) A4/LETTER Count : 3Scanner PM Count : 9 (------) A4-R/LETTER-R Count : 10ADF Count : 1 ------ A3/LEDGER Count : 0OPC Drum Count : 13 ------ B4/LEGAL Count : 0Process Unit Count : 13 (------)ADF PM Count : 1 F7-04 ADF Count : 1Fuser Web Count : 240986 ADF Read Count : 1Developer Count : 13 Scanner Count : 9Corona Cleaning Count : 13 Scanner Read Count : 9Avg. Print/Drum Rise Up : 1.00Total OPC Rotation Time : 0.03 F7-05 Copy Print Count : 3Avg. Sec/Drum Rise Up : 0.01 Copy Scan Count : 4

F7-03 Sheet Bypass Count : 0 F7-06 PC Print Count : 01st Paper Tray Count : 3 PC Scan Count : 62nd Paper Tray Count : 103rd Paper Tray Count : 0 F7-07 FAX Transmit Count : 04th Paper Tray Count : 0 FAX Receive Count : 0

FAX Print Count : 0

Call Counter Pre-Set Value : 14000

PRINT ERROR:

NO. DATE & TIME ERROR CODE ERROR COUNT | NO. DATE & TIME ERROR CODE ERROR COUNT-------------------------------------------------------------------------------------------01 MMM-dd-yyyy 20:07 E04-01 00-00000013 |02 MMM-dd-yyyy 20:04 E04-01 00-00000013 | | | | | | | | | | |

| -------------------------------------------------------------------------------------------

-LOGO PANASONIC -

***** *********************** -CHARACTER ID - ***** -31415926535897932384-*********

SC : SPC :

104JUN 2004Ver. 2.0

UF-9000
DP-180/190
4.2.8. Service Mode 9 (System Maintenance)4.2.8.1. OverviewThis Service Mode is used to maintain the machine. Use the following procedure for System Maintenance.

Press the “V”, ”/\” arrow keys to select the "9: System Maintenance" on the display.↓

Press the “SET” key to select the "8: Send RCV’D File". The display changes to the Fax Mode.↓

Select the desired Fax number.↓

Press "START" to send the Fax. After the transmission, the machine returns to the Stand-by Mode.

Note:If there is NO File in the machine, this operation will not function.Press the “STOP” key twice to exit the service mode.

System Maintenance Table

No. Maintenance Mode Description08 Send RCV'D File Transfers documents from memory to another fax machine

during a fatal printer error.

105JUN 2004Ver. 2.0

UF-9000
DP-180/190
5 Exploded View & Parts ListNote:

1. Panasonic Document Imaging Company and other Panasonic Sales Companies reserve the right to change any information enclosed herein without prior notification. (This includes, but is not limited to, parts pricing, availability, and text)

2. Electrical parts supplied may include previously used components.3. Important Safety Notice

Components identified by a mark, have special characteristics important for safety. When replacing any of these components, use only manufacturerís specified parts.

4. In Remarks column, "PM" indicates “Preventive Maintenance Part".5. In Remarks column, "RTL" indicates that the Retention Time is limited for this item. After the

discontinuation of this assembly in production, the item will continue to be available for a specific period of time. The retention period of availability is dependant on the type of assembly, and in accordance with the laws governing part and product retention. After the end of this period, the assembly will no longer be available.

6. This “Unit" which includes other itemized parts is provided as “Limited Availability" for your convenience, and will only be offered for up to 3 years after the production of the unit ceases. However, the individual contents of the assembly will be available for the standard period.

7. Supplier "OAPD" is the supplier code 00029151.8. For Screw identification and Part Number, please refer to the last section of this chapter.

106JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.1. Destination Codes

5.1.1. Destination Codes for Fax Option

Code Destination Code DestinationAG Germany EP Spain; Greece; PortugalAL Australia; New Zealand ER Denmark; Norway; Sweden; Finland;

TurkeyAM Switzerland

AU USA, Canada, Mexico; Panama (120 VAC Power Supply)

ES Saudi Arabia; U.A.E.

YA Panama; Chile(220-240 VAC Power Supply)AV France

EB England; Singapore; Malaysia; Hong Kong YC South Africa; Egypt; Russia;

Hungary; Czech; PolandEE Italy YV ChinaEH Belgium; Netherlands

Code Destination Code DestinationAA Austria YA Panama; Chile

(220-240 VAC Power Supply)AB EnglandAE Taiwan YC Universal 220-240 VAC Power

Supply VersionAG GermanyAH Netherlands YG GreeceAJ Spain YK South KoreaAK Hong Kong SAR, PRC YM MalaysiaAL Australia YP Poland; Hungary; CzechAM Switzerland YR RussiaAP Portugal YS Saudi ArabiaAR Belgium YV ChinaAT Turkey YW South AfricaAU USA; Puerto Rico; Canada YX SingaporeAV France YY Mexico; Panama

(120 VAC Power Supply)AW New ZealandEE ItalyEN Denmark; Finland; Norway; Sweden

107JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.2. Control Panel Unit

Safety Mark

Ref. No.

Parts Number Part Name Supplier Remarks Destination

101 PJKEB0115Z Base, Panel All

102 PJKKB0001Z Holder, Battery All

103

PJGPB0011Z

Cover, Panel

For UF-9000/DP-190

AU

For DP-180

Except AG, AV, YV

PJGPB0011Y AG

PJGPB0011X AV

PJGPB0011W YV

104 DZKB000796 Key, Start All

105 DZKB000762 Key, Stop All

106 DZKB000641 Key, Reset All

107 DZKB000760 Key, Function All

108 DZKB000922 Key, A All

109 DZKB000640 Key, B All

110 DZKB000862 Key, Copy All

111 DZKB000858 Key, Scan/File All

112 DZKB000637 Key, Print All

113 DZKB000803 Key, Touch3 All

114 PJBCB0017Z Key, Fax/Email All

115 PJBCB0022Z Key, Ten All

116 PJBCB0016Z Key, Contrast All

117 PJBCB0018Z Key, Zoom All

118

PJBCB0019Z

Key, 1

For UF-9000 AU

PJBCB0019Y For DP-180/190 Except AV

PJBCB0019X For DP-180 AV

119

PJBCB0020Z

Key, 2

For UF-9000 AU

PJBCB0020Y For DP-180/190 Except AG, AV

PJBCB0020XFor DP-180

AG

PJBCB0020W AV

120 PJBCB0021Z Key, 3 All

121 PJKEB0120Z Lamp, Doing All

122 PJBAB0020Z Holder, LCD All

123 PJHXB0019Z Sheet, Insulated All

124

PJGKB0087Z

LCD Window

For UF-9000 AU

PJGKB0107Y For DP-190 AU

PJGKB0107X

For DP-180

AG

PJGKB0107W AV

PJGKB0107V YV

PJGKB0107ZExcept AU, AG, AV, YV

125

PJGKB0088Z

Sheet, Panel 1

For UF-9000/DP-190

AU

PJGKB0088Y

For DP-180

AG

PJGKB0088X AV

PJGKB0088W YV

PJGKB0088UExcept AU, AG, AV, YV

108JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 1 Control Panel Unit

F10

126

124

125

103

121

F10

1907

1943

1942

115

104

105

106

107

120

117

1909

1941

113

110

112

111

114

F10

F10

127

123

122

1905

129

118

119

1906

1908

116130

108

108

109For DP-180/190only

For DP-180/190

For UF-9000

109

101

V6

102

128

F10

1943

1948

19391940

109JUN 2004Ver. 2.0

UF-9000
DP-180/190
Safety Mark

Ref. No.


126

PJGKB0089Z

Sheet, Panel 2

For UF-9000 AU

PJGKB0089Y For DP-180/190Except AG, AV, YV

PJGKB0089X

For DP-180

AG

PJGKB0089W AV

PJGKB0089V YV

127 DZDA000047 LCD Module All

128 CR2032 Battery All

129 PJHXC0001Z Sheet, Protect All

130 PJBCB0023Z Key, C For DP-180/190 All

1905Depends on Destination

PC Board, PNL1See Sect. 5.18. PC Boards


PC Board, PNL2See Sect. 5.18. PC Boards

1907 DZEC102980 PC Board, PNL3 RTL, PbF All



1939 DZFP001561 Harness, PNL1-PNL2_17PIN All





1948 DZFP001574 Harness, Book-PNL All

F10 XTB3+8G Screw All

V6 XTB3+8JFN Screw OAPD All

110JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 1 Control Panel Unit

F10

126

124

125

103

121

F10

1907

1943

1942

115

104

105

106

107

120

117

1909

1941

113

110

112

111

114

F10

F10

127

123

122

1905

129

118

119

1906

1908

116130

108

108

109For DP-180/190only

For DP-180/190

For UF-9000

109

101

V6

102

128

F10

1943

1948

19391940

111JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.3. Scanner Unit

Safety Mark

Ref. No. Parts Number Part Name Supplier Remarks Destination

201 81150C008H Switch, Magnetic All

202 92110C001H Shaft, IR All

203 92143D001H Belt All

204 92102C001H Plate, Motor Fix All

205 92123D001H Gear, 60T/P16T All

206 91123D035H Collar All

207 91133D004H Spring, Tension All

208 91102D012H Sheet, Holder All

209 91102D011H Holder, Pulley All

210 91123D034H Pulley, Idle All

211 92123C003H Cover, Hole All

212 92123A001H Frame, IR Base All

213 92125D006H Seal, CCD Harness All

214 92130D002H Sponge All

215 92102C007H Plate, Metal All

216 92102C002H Cover, Main Board All

217 92102C003H Base, Cover All

218 92123C004H Cover, Harness All

219 7UA1810A681B Assembly, Scanner Cover All

221 738902000340 Motor All

222 737430400030 Sensor, Home Detect All

223 92102D005H Spring, Plate All

224 783309000120 E-Ring All

225 92129D010H Seal, Screw All

226 92102D007H Plate, FFC Set All

227 92102D008H Plate, Seal All

228 92102D009H Plate, Core Set All

230 92129D021H Gasket 1 All

231 92129D022H Gasket 2 All

1910 7UA1810AF11A PC Board, SPC PbF All

H8 XTW3+8LFN Screw All

V7 XTW3+8PFN Screw All

112JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 2 Scanner Unit

230 231213

214

226

V7

215

216

217

218

212211

202

204

205

206

203206 224

210

208

207

209

201

219V7 225

H8

V7

H8

V7

Fig. 3

V7

V7

1910

H8

V7

V7

221

V7222

224

223

H8

227

223

V7

228

113JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.4. CCD

Safety Mark

Ref. No. Parts Number Part Name Supplier Remarks Destination

3017UA1810A721B

Assembly, CCD ModuleFor UF-9000/DP-190

AU

7UA1810A722B For DP-180 Except AU

303 738903000110 Lamp, Scanning All

305 735109001050 Core All

306 81325D113H Cover, Inverter All

1922 739909000620Cable, CCD (Flat Harness)

All

W8 XTN3+8JFN Screw All

114JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 3 CCD

306

303

W8

W8

301

305

305

1922

115JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.5. ADF

Safety Mark

Ref. No.


401 92123A005H Cover, Top ADF All

402 92123A007H Cover, Rear ADF All

403 91134C001H Hinge, ADF All

404 92130D001H Pad, Scanning All

405 91123A004H Base, ADF All

406 91123D006H Level, Sensor All

407 91102D005H Plate, Roll Fix All

408 91123D025H Roller All

409 91102D004H Plate, ADF Roller Fix All

410 92123D004H Gear, 23S All

411 92123D005H Gear, 19S All

412 91123D021H Base, Pickup All

413 91123D022H Arm, Stopper All

414 91127C004H Roller, Pickup PM All

415 91110D003H Shaft, Pickup All

416 81123D150H Gear, 23T All

417 91127C003H Roller, ADF PM All

418 91110D002H Shaft, ADF All

419 92110D001H Shaft, Transfer All

420 91123D024H Shutter, Right All

421 91123D023H Shutter, Left All

422 81123D148H Gear, 12T All

423 92123D003H Gear, 20T All

424 92142D001H Clutch, One Way All

425 91110D007H Pin All


427 91129D010H Sheet, Trace All

428 737430400020 Sensor, 400mm All

429 92123A006H Guide, Document All

430 92123B001H Guide, Extend Document All

431 92123C002H Guide, Front All

432 92123C001H Guide, Rear All

433 91123D008H Rack, Guide All

434 81123D156H Gear, 24T All

435 91123D005H Cover, Tray All

436 92125D001H Sheet, Tray All

437 92125D007HLabel, Max. Capacity Indicator

All

439 91123D042H Base, Dummy Hinge All

440 91137D002H Screw, Dummy Hinge All

116JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 4 ADF (1/2)

430436432

437

V7

405

427

427

433

429

431

434

433435

V7

404403

425

425V8442

446

402

439

443

414

447

415

411410

418

417

416

413

412

413

449

406428

419

423424

445409

V7

426

408

407

422 420

421

401

V7

1911

H8

V7

441440

444

444

H8

448

117JUN 2004Ver. 2.0

UF-9000
DP-180/190
Safety Mark

Ref. No.


441 92123D011H Cover, Dummy Hinge All

442 7UZFFA02501B ADF Unit All

443 91123D043H Hinge, Upper Dummy All

444 92130D003H Cushion, Stopper All

445 92130D004H Cushion, Pick-up All

446 PJQTB0292Z Label, Color All

447 21070121706 E-Ring All

448

PJQTB0265Z

Label, F

For UF-9000 AU

PJQTB0265Y For DP-180/190Except AG, AV, EE, YV

PJQTB0265X

For DP-180

AG

PJQTB0265W AV

PJQTB0265V EE

PJQTB0265U YV

449 7UA1810A631B Assembly, Pickup All

1911 7UA1810AS11A PC Board, ADF PbF All

H8 XTW3+8LFN Screw All


V8 XTW4+16P Screw All

118JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 4 ADF (1/2)

430436432

437

V7

405

427

427

433

429

431

434

433435

V7

404403

425

425V8442

446

402

439

443

414

447

415

411410

418

417

416

413

412

413

449

406428

419

423424

445409

V7

426

408

407

422 420

421

401

V7

1911

H8

V7

441440

444

444

H8

448

119JUN 2004Ver. 2.0

UF-9000
DP-180/190
Safety Mark

Ref. No.


501 92123A004H Base, ADF All

502 92129D002H Sheet, Protect Cover All

503 91127D001H Roll, Exit All

504 91133D001H Spring, Exit Roller All

505 92123D015H Cover, Protect All

506 91102D007H Spring, Roller Pressure All

507 91123D003H Arm, Sensor All

508 91123D001H Roll, Pinch All

509 91100D001H Shaft All

510 91123A003H Cover, Frame All

511 91123A002H Frame, ADF All

512 91192D001H Plate, Motor Attachment All


514 92123D006H Holder, Pickup Sheet All

515 91134D001H Sheet, Pickup All

516 91127C001H Roller, Feed PM All

517 91102D002H Spring, Ground All

518 91102C004H Plate, Reading All

519 91127C002H Roller, Exit All

520 92123D012H Stud, Gap All

521 91123D012H Gear, 33T All

522 91102C002H Plate, Front Attachment All

523 92123D014H Lib, Fix Plate All

524 91123D053H Hook, Top Cover All

525 91123D002H Knob, Paper Transport All

526 91102B002H Plate, Rear Attachment All

527 91123D013H Gear, 48T All

528 91123D009H Gear, 18/45T All

529 91123D015H Gear, 18/40T All

530 92123D002H Gear, 32/15T All

531 91123D014H Gear, 26T All

532 91133D005H Spring, Reading Plate All

533 91123D010H Gear, 30T All

534 91129D008H Sheet, Guide All

535 81141C001H Magnetic All

536 92129D001H Sheet, White Reference All

537 91142D002H Bushing, D6 All

538 92129D004H Sheet, Gap Limit All

539 91134D002H Brush, Antistatic All

540 737430400010 Sensor, 320mm All

120JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 5 ADF (2/2)

507540

550

502

505

509

V7

V7

506

508

553 554

501

538

536552

534

518

516

522

532

520

537

515

514

539

549

510

547

513

V7

W5

546

551548

503504

525

V9

524 V7

523

519

537

537

P8517

511526

542524

541

512

V9

531

530528

527

521

533

529

V9

535

W1

121JUN 2004Ver. 2.0

UF-9000
DP-180/190
Safety Mark

Ref. No.


541 738902000331 Motor All

542 737428200050 Sensor, Cover All

546 91123D004H Base, Pad All

547 91127D002H Rubber, Separation PM All

548 91129D004H Sheet, Pad All

549 91129D009H Sheet, Pressure All

550 91133D006H Spring, Torsion All

551 81158D013H Rivet, Snap All

552 92129D008H Sheet, Plate All

553DZHT000027

Stamp HeadAU

DZHT000004 Except AU

554 7UA1810A951B Assembly, Stamp All

P8 XTW3+8P Screw All


V9 XTW3+6LFN Screw All

W1 XTS3+8J Screw All

W5 XSN2+10FN Screw All

122JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 5 ADF (2/2)

507540

550

502

505

509

V7

V7

506

508

553 554

501

538

536552

534

518

516

522

532

520

537

515

514

539

549

510

547

513

V7

W5

546

551548

503504

525

V9

524 V7

523

519

537

537

P8517

511526

542524

541

512

V9

531

530528

527

521

533

529

V9

535

W1

123JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.6. Cover Assembly

Safety Mark

Ref. No.


601

PJKEB0081Z

Cover, Front

For UF-9000 AU

PJKEB0081Y For DP-190 AU

PJKEB0081X For DP-180 Except AU

602 PJHRB0567Z Support, Right Paper All

603 PJHRB0568Z Support, Left Paper All

604 PJHRB0045Z Rack, Guide OAPD All

605 PJHRB0046Z Gear, Paper Guide Pinion OAPD All

606 PJBAB0011Z Hook OAPD All

607 PJYK4P7305MAssembly, Pinch Roller Holder

OAPD All

608 PJDSB0034Z Spring, Pinch Roller OAPD All

609 PJDSB0145Z Spring, Cleaning Roller OAPD All

610 PJDRB0017Z Roller, Pinch OAPD All

611 PJDRB0093Z Roller, Cleaning OAPD All

612 PJYKF2300AU Door, Rear All

613 PJDFB0008Z Shaft, Roller OAPD All

614 PJDSB0112Z Spring OAPD All

615 PJKEB0110Z Cover, Right Side All

616 PJKEB0111Z Cover, Left Side All

617 PJKEB0112Z Cover, Rear All

618 PJKEB0116Z Cover , Right Leg All

619 PJKEB0117Z Cover, Left Leg All

620 PJKEB0118Z Cover, PCB All

621 DZMA003267 Cover, Flash Memory Card All

622 PJQTB0264Z Sheet, Right Cover All

623 PJKEB0113Z Cover, Top All

624 PJKEB0114Z Tray, Sub Paper All

625 PJKEB0130Z Cover, Rear Paper Tray All

626DZDU000025

Handset

Refer to 5.1.1.

Except AK

DZDU000027 AK

627DZJE000738

Cradle, UpperAU

DZMA000260 Except AU

628DZJE000740

Cradle, LowerAU

DZMA000269 Except AU

629 DZFN000060 Cord, Handset All

630DZFN000082

Cord, CradleExcept AK

DZFN000115 AK

124JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 6 Cover Assembly

602

606

T8

604

605

T8

T8

603

601

606T9

T9

T9

V6

635

622

631

W2

T9 610

608611

609610

608

607632 615

618

V6

633

V6

628

19

1946

626

629627

630

616

619

T9634

V6

624

623

V9

606

612

606

V6

625

617

613

610

614

621

620V6

125JUN 2004Ver. 2.0

UF-9000
DP-180/190
Safety Mark

Ref. No.


631 DZDR000014 Speaker All

632 DZNK005395 Label, Laser Caution All

633 PJQTC0003Z Label, Flash Memory All

634 PJMDB0316Z Plate, Cover All

635 FFPTE2650 Label, Energy Star All

1946

DZEC101941

PC Board, SRU Refer to 5.1.1.

AU

DZEC102525 AK

DZEC102526 AT

DZEC102566 YC

DZEC102527 YW

19 XTB3+8J Screw All

T8 XTW26+8S Screw OAPD All



V9 XTW3+6LFN Screw All

W2 DZZSP29011 Screw All

126JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 6 Cover Assembly

602

606

T8

604

605

T8

T8

603

601

606T9

T9

T9

V6

635

622

631

W2

T9 610

608611

609610

608

607632 615

618

V6

633

V6

628

19

1946

626

629627

630

616

619

T9634

V6

624

623

V9

606

612

606

V6

625

617

613

610

614

621

620V6

127JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.7. Right Side Parts

Safety Mark

Ref. No.


701 PJMDB0288Z Cover, SC All

702 PJMDB0287Z Base, SC All

703 PJMDB0286Z Base, Rear PC Board All

704 DZJF000462 Guide, Flash Memory Card All

705 PJUSB0130Z Plate, Spring All

706 N3CABRD00005 HDD Unit All

707 DZJC000389 Bracket, HDD All

708 DZJH000084 Support, Locking All

709 PJWC1P7105MAssembly, Engine Board Shield Base

OAPD All

710 DZJC000390 Bracket, Counter All

711 DZTK000002 Counter, Mechanical All

712 PJRAC0001Z Sheet, FM All

713 PJMDB0156Z Clamp OAPD All

714 DZJK000069 Clamp All


PC Board, SCSee Sect. 5.18. PC Boards

1902 PJWPUF9KEM PC Board, Engine Control RTL, PbF All


PC Board, FXBSee Sect. 5.18. PC Boards

1931 DZEC103051 PC Board, DC RTL, PbF All

1934 DZEC102137 PC Board, FRM8 All

1935 ----- Hardware KeyAvailable as Sales Item

1936 PJWP3P7105M1PC Board, 2nd Paper Feed Module I/F

OAPD RTL, PbF All

1944 PJWP3P7100M1PC Board, Low Toner Sensor

OAPD RTL, PbF All


L9 XTB3+4F Screw All


U1 XTW3+6L Screw All

V5 XTW3+6LFC Screw All

128JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 7 Right Side Parts (1/2)

1931

706

V5

L9

L9 707

711

710

U1

712

703

U1

U1

705

U1

1903

1936

U1

T9

1944

709

T9

713

1902

U17021901

714

704

1935

708

708

1934U1

701

U1

U1

2405

129JUN 2004Ver. 2.0

UF-9000
DP-180/190
Safety Mark

Ref. No.


801 PJDGB0052Z Gear, ADU Drive OAPD All

802 PJDGB0070Z Gear, Registration Drive OAPD All

803 PJDGB0072Z Gear, Idle Z19 OAPD All

804 PJDGB0071Z Gear, Double Teeth OAPD All

805 PJDGB0073Z Gear, Idle Z14 OAPD All

806 PJDGB0028Z Gear, Ratchet OAPD All

807 PJDGB0043Z Gear, Registration Arm OAPD All

808 PJDGB0042ZGear, Registration Internal

OAPD All

809 PJDGB0029Z Gear, Planetary OAPD All

810 PJNW4111Z Washer, Plastic OAPD All

811 PJNW525Z Spacer OAPD All

812 PJDGB0051Z Gear, Fuser Drive OAPD All

813 PJDSB0039Z Spring, Gear Tension OAPD All

814 PJDGB0204Z Gear, Intermediate Fuser OAPD All

815 PJDSB0211Z Spring, Pickup OAPD All

816 PJUSB0025Z Spring, Ground OAPD All

817 PJHRA0316Z Guard, Edge OAPD All

818 PJMDB0292Z Bracket, Right Side Cover All

819 PJMDB0259Z Base, Right Side All

820 PJMDB0261Z Bracket, Right Side All

821 PJZC2P7100M Bracket, Gear Support OAPD All

822 PJWMP7100MAssembly, Registration Solenoid

OAPD All

823 PJZHP7105M Bracket, Fuser Drive Gear OAPD All

824 PJHRB0327Z Clamp OAPD All


826 PJJTC0002Z Cable, Ground All


1947 PJWP2P7105M1 PC Board, No Paper Sensor OAPD RTL, PbF All



3F XYN3+F5 Screw All



130JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 8 Right Side Parts (2/2)

820

825

U1

818

T9

U1

2404

811

812

814

813

T9

823819

U1

801

810802

811

803805

1947 T9811

804

808

807806

811

809

T9

U1

817

713

713

T9

Fig. 9

U1

826

U1

816U1

T9

3F

821

822

815

816 U1

824

816 U1

713

825

2405

131JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.8. Motor and Drive Gear Unit

Safety Mark

Ref. No.


901 PJDGB0047Z Gear, OPC B OAPD All

902 PJDGB0048Z Gear, OPC A OAPD All

903 PJDGB0049Z Gear, Fuser OAPD All

904 PJDGB0056Z Gear, Registration A OAPD All

905 PJDGB0069Z Gear, Registration B OAPD All

906 PJNW620Z Washer OAPD All

907 L6CCKGEK0003 Motor OAPD All

908 PJZHP7100MAssembly, Drive Gear Bracket

OAPD All

909 PJZHP7305M Bracket, Motor OAPD All



132JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 9 Motor and Drive Gear Unit

909

907

811

902

811

905

901

903

906

904

908

U1

U1

133JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.9. Left Side Parts

Safety Mark

Ref. No.


1001 PJDSB0033Z Spring, Grid OAPD All

1002 PJDSB0148Z Spring, Charge OAPD All

1003 PJDSB0009Y Spring, OPC OAPD All

1004 PJDSB0149Z Spring, Developer OAPD All

1005 N0GG4E000002 HVPS OAPD All

1006 L6FALEGK0009 Motor, Fan OAPD All

1007 PJNEB0008Z Screw OAPD All

1009 PJDRB0059Z Roller, Sub OAPD All


1011 PJMDB0291Z Bracket, Side Cover A All

1012 PJMDB0289Z Bracket, Side Cover B All

1013 PJMDB0290Z Bracket, Left Side Cover All

1014 PJMDB0258Z Stay, Rear All

1015 PJMDB0260Z Base, Left Side All

1016 PJMDB0262Z Bracket, Left Side All

1017 PJMDB0263Z Bracket Left Rear All

1018 PJMDB0264Z Bracket, Right Rear All

1019 PJHRB0659Y Guide, Exit Paper All

1020 PJQTB0263Z Sheet, HVPS Insulation All

1021PJWPWU00001Z

Assembly, LVPSFor UF-9000/DP-190

AU

PJWPF2300EB For DP-180 Except AU

1022 PJHE5065Z Screw OAPD All


613 PJDFB0008Z Shaft, Roller OAPD All

2403 DZJK000057 Edge Saddle All



P3 XTW3+8L Screw All



U3 XYC3+FF8C Screw OAPD All

134JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 10 Left Side Parts

U11018

1014

1019

U12404

1017

U1

2405

2403

P3610

T9

1015

U1

2405

1016

1013

U1

1007

1006

1001

1005

1004

1020

1002

1003T9

T9

1012

1011

U1U1

1009

610

613

1010

1010

U3

1021

1022

135JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.10. Rear and Upper Side Parts

Safety Mark

Ref. No.


1101 PJZBP7305MAssembly, Upper Exit Roller Holder

OAPD All

1102 PJDGB0024Z Gear, Z21 Fuser OAPD All

1103 PJDGB0026ZGear, Z36 Upper Exit Roller Drive

OAPD All

1104 PJDGB0025Z Gear, Internal OAPD All

1105 PJDGB0027Z Gear, Black Ratchet OAPD All

1106 PJDGB0203ZGear, Upper Exit Roller Drive

OAPD All

1107 PJDSB0016Z Spring, Ratchet OAPD All

1108 PJNW721Z Poly Slider OAPD All

1109 PJZC1P7100MAssembly, Upper Exit Roller Holder Cover

OAPD All

1110 PJDPB0001ZSolenoid, Upper Exit Roller with Plunger

OAPD All

1111 PJZR2P7305MAssembly, Upper Exit Roller

OAPD All

1112 PJWSP7105MSwitch, Front Door Safety Interlock

OAPD All

1113 PJWS2P7100MSwitch, OPC Drum Unit Interlock

OAPD All

1114 PJWEP7305M LSU OAPD All

1116 K5AT281613 Core OAPD All

1937 PJWP2P7100M1PC Board, Paper Exit/ADU Paper Jam Sensor

OAPD RTL, PbF All

806 PJDGB0028Z Gear, Ratchet OAPD All




U4 XTW3+12S Screw OAPD All

U9 XSN3+4 Screw All

W4 XTB2+12J Screw OAPD All

W7 PJNAC0003Z Screw All

136JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 11 Rear and Upper Side Parts

W71114

1116

1112

W4

1937

1113

W4

1104

809

1102

1105806

1103

1103

1104

809

T9

11061110

1107

U9 T9

1109

11111108

U4

1101

U1

Fig. 12

137JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.11. Fuser Unit

Safety Mark

Ref. No.


1201 PJDFB0122Z Shaft, Fuser Drive OAPD All


1203 PJMDB0018Z Plate, Lead Wire OAPD All

1204 L2AA00000090 Thermostat All

1205 PJDRB0091Z Roller, Heat OAPD All

1206 PJDJB0008Z Bushing, Left Heat Roller OAPD All

1207 PJDJB0009ZBushing, Right Heat Roller

OAPD All

1208 PJDGB0021Z Gear, Heat Roller OAPD All

1209

L9DAEJ000001

Lamp, Halogen

OAPD For UF-9000 AU

A4DP3L000003 For DP-190 AU

A4DP7K000002 For DP-180 Except AU

1210 PJMDB0257Y Plate, Lead Wire OAPD All

1212 PJHRB0636Z Base, Fuser Unit OAPD All

1213 PJDSB0015ZSpring, Paper Jam Sensor Lever

OAPD All

1214 PJDJB0010Z Bushing, Pressure Roller OAPD All

1215 PJDSB0205Z Spring, Pressure Roller OAPD All

1216 PJDRB0092Z Roller, Pressure OAPD All

1217 PJDSB0018Z Spring, Pinch Roller A OAPD All

1218 PJMDB0019Y Ground, Fuser OAPD All

1219 PJJRB1025Y Cable, Fuser OAPD All

1220 PJHRB0637Z Lever, Paper Jam Sensor OAPD All

1221 PJHRB0635Z Holder, Heat Roller OAPD All

1222 PJMDB0253Z Plate, Separator OAPD All

1223 PJDSB0206Z Spring, Separator OAPD All

1224 PJHRB0638Z Cover, Left Fuser OAPD All

1225 PJHR9224Z Separator OAPD All

1226 PJZC3P7100MAssembly, Side Fuser Cover

OAPD All

1227 PJZR3P7100MAssembly, Lower Exit Roller

OAPD All

1228 PJZRP7305M Assembly, Cleaning Roller OAPD All

1229 L2AA00000088 Thermistor All

138JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 12 Fuser Unit

12281217

12131220

1212

1227

1208

1207

1214

1215

1215 12061216 1214

1217

610

G8

V1

V1

12091205

1102

1106

1221

1202

1201

T9

1226

T9

U5

U4

T9

T91218

1224

1225

1223 T9

1222

1219

1203

T9

1229

T9T9

U3 U3

1204

12191204

1210

(1210)

1203

1108

1115

1117

139JUN 2004Ver. 2.0

UF-9000
DP-180/190
Safety Mark

Ref. No.




1106 PJDGB0203ZGear, Upper Exit Roller Drive

OAPD All


1115J0KF00000046 or

Ferrite Core AllJ0KF00000015

1117

PJZFUS00001Z

Assembly, Fuser Unit

For UF-9000 AU

PJZSF2300AU For DP-190 AU

PJZSF2300EB For DP-180 Except AU

G8 XWC3B Washer, Star All


U3 XYC3+FF8C Screw OAPD All

U4 XTW3+12S Screw OAPD All

U5 XTW3+12SFZ Screw OAPD All

V1 XYC3+FF6 Screw OAPD All

140JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 12 Fuser Unit

12281217

12131220

1212

1227

1208

1207

1214

1215

1215 12061216 1214

1217

610

G8

V1

V1

12091205

1102

1106

1221

1202

1201

T9

1226

T9

U5

U4

T9

T91218

1224

1225

1223 T9

1222

1219

1203

T9

1229

T9T9

U3 U3

1204

12191204

1210

(1210)

1203

1108

1115

1117

141JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.12. Pickup Roller and Paper Feed Roller

Safety Mark

Ref. No.


1301 PJDGB0040Z Gear, Pickup Internal OAPD All

1302 PJDGB0041Z Gear, Pickup Arm OAPD All

1303 PJDRB0021Z Roller, Registration OAPD All

1304 PJDGB0038Z Gear, Registration Roller OAPD All

1305 PJDRB0022Z Roller, Paper Feed OAPD All

1306 PJDJ05041RZ Bearing, R5 OAPD All

1307 PJDGB0039Z Gear, Paper Feed Roller OAPD All

1308 PJHRB0070Z Wheel, Drive OAPD All

1309 PJDJB0019Z Bushing OAPD All

1311 PJDFB0163Z Shaft, Pickup Roller OAPD All

1312 PJDSB0207Z Spring, Pickup Holder OAPD All

1313 PJHRB0640Z Adapter, Pickup Holder OAPD All

1314 PJDSB0208Z Spring, Dust Scraper OAPD All

1315 PJZC1P7305MAssembly, Dust Scraper Cover

OAPD All

1316 PJZR1P7305M Roller, Pickup OAPD PM All


1318 PJZEP7305M Guide, Sub. Paper OAPD All

1319 PJZE1P7100M Assembly, Pickup Lever OAPD All

1320 PJWMP7305M Assembly, Pickup Solenoid OAPD All

611 PJDRB0093Z Roller, Cleaning OAPD All




1022 PJHE5065Z Screw OAPD All

1105 PJDGB0027Z Gear, Black Ratchet OAPD All

U8 XTW3+U8S Screw OAPD All

142JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 13 Pickup Roller and Paper Feed Roller

1306

13041306

13071308

13191311

13061105

1302

809

809

1301

815

1320

1022

U8

1306

810

1313

1316

1315

1312

1303

1305

1318

1309

1309

1317 6111314

143JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.13. Bottom Side Parts

Safety Mark

Ref. No.


1401 PJUAB0024Y Plate, Lower Base OAPD All

1402 PJMDB0020Z Plate, ADU Pinch Roller OAPD All

1403 PJDRB0018Z Roller, ADU Pinch OAPD All

1404 PJDFB0009Z Shaft, A/D Roller OAPD All

1405 PJDSB0041Z Spring, Pinch Roller OAPD All


1407 PJNW410Z Washer OAPD All

1408 PJUAB0005YPlate, ADU Registration Roller

OAPD All

1409 PJDRB0014ZShaft, ADU Registration Roller

OAPD All

1410 PJDJ05011CZ Bearing, C5 OAPD All

1411 PJDGB0030Z Gear, A/D Unit Union OAPD All


1413 PJJTCC014Z Cable OAPD All

1414 PJHRB0320Z Lever, No Paper Sensor OAPD All

1415 PJHRB0075ZLever, Registration Sensor

OAPD All

1416 PJHRB0076ZLever, Paper Detect Sensor

OAPD All

1417 PJDSB0035Z Spring, Registration OAPD All

1418 PJZUP7100M Pan, Jam Release OAPD All


1938 PJWP2P7305MPC Board, Registration/Paper Detect Sensor

OAPD RTL, PbF All



U6 XUC4VW-V E-Ring OAPD All

U7 PJNEB0003Y Screw OAPD All


144JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 14 Bottom Side Parts

1938

T9

1416 1415

1417

1414

1409

1306U6

1410

1411

1408

1401T9

P3

14031405

1405

U1

U1

1404

14071406

1402

1406

1413

1412

U7

U7

1412T9

1418 T9

145JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.14. Mechanical Base

Safety Mark

Ref. No.


1501 PJHRB0324Z Holder, Transfer Roller OAPD All

1502 PJDSB0040Z Spring, Transfer OAPD All

1503 PJDRB0081Z Roller, Bias Transfer OAPD PM All

1504 PJHRB0078Z Bushing OAPD All

1505 PJDGB0057Z Gear, Transfer OAPD All

1506 PJDJB0020Z Bearing, U OAPD All

1507 PJHRB0038Z Arm, Left Pressure OAPD All

1508 PJHRB0037Z Arm, Right Pressure OAPD All

1509 PJUSB0011Y Plate, Ground OAPD All

1510 PJUSB0008ZPlate, Transfer Bias Roller

OAPD All

1511 PJDSB0026Z Spring, Left OPC OAPD All

1512 PJDSB0008Z Spring, Right OPC OAPD All

1513 PJDSB0043Z Spring, Left Registration OAPD All

1514 PJDSB0010ZSpring, Right Registration

OAPD All

1515 PJDSB0024Z Spring, Paper Tray Guide OAPD All

1516 PJMCB0070Z Plate, Ground 1 OAPD All

1517 PJMCB0068Z Plate, Ground 2 OAPD All

1518 PJZCP7305M Assembly, Paper Chute OAPD All








V1 XYC3+FF6 Screw OAPD All

146JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 15 Mechanical Base

1507

U8

1515

1513

1508U8

1515

1514

1518

1503811

1504

8111504

1505

811

1501

1501

1502

1502

1506

T9

1509

V1

T9

1511

U8

1510

U1

1516

T9

T9

8151512

U1

P3713

1517

147JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.15. Paper Tray

Safety Mark

Ref. No.


1601 PJMDB0026Y Lifter, Paper OAPD All

1602 PJHSB0007Z Pad, Friction OAPD All

1603 PJDSB0179Z Spring, Retard Pad OAPD All

1604 PJHRB0031Z Guide, Right Paper Side OAPD All

1605 PJHRB0032Z Guide, Left Paper Side OAPD All

1606 PJDSB0210Y Spring, Friction OAPD All

1607 PJDSB0020Z Spring, Stopper OAPD All

1608 PJHRB0034Z Stopper OAPD All

1609 PJHRB0029Y Assembly, Paper Tray Base OAPD All

1610 PJHRB0030ZTray, Paper Tray Extension

OAPD All

1611 PJHRB0033Z Knob, Paper Size OAPD All

1612 PJHRB0307ZIndicator, Orange Paper Level

OAPD All

1613 PJDG50133Z Gear, Pinion OAPD All

1614 PJHRB0036Z Rack OAPD All

1615 PJZEP7100M1 Pad, Separation OAPD PM All

1616 PJHRB0476Z Adapter, Retard OAPD All

1617 PJGEC0002Z Sheet, Paper Tray AFor UF-9000/DP-190

AU

1618 PJGEC0003Z Sheet, Paper Tray BFor UF-9000/DP-190

AU

1619 PJGEC0006Z Sheet, Paper Tray CFor UF-9000/DP-190

AU

1620 PJGEC0007Z Sheet, Paper Tray DFor UF-9000/DP-190

AU

1621 PJGEC0008Z Sheet, Paper Tray EFor UF-9000/DP-190

AU

1622 PJGFC0011ZLabel, Max. Level Indicator 1

All

1623 PJHRC0051Z Sheet, Separation Pad All


148JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 16 Paper Tray

1606

1602

U8 U8

U8

1613

1614

16141610

16111604

1612

U8

1605

1622

1601

16081607

16031616

16151606

1609

1623

1617

1618

1621

1620

1619

149JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.16. 2nd Paper Feed Module

Safety Mark

Ref. No.


1701 PJKEB0019Z Cover, Front OAPD All

1702 PJKEB0097Z Cover, Right All

1703 PJKEB0098Z Cover, Left All

1704 PJUSB0027Z Plate, Pinch Roller OAPD All

1705 PJDRA0051Z Roller, Pinch OAPD All

1707 PJHRB0082Z Guide, Left Front OAPD All

1708 PJHRB0083Z Guide, Left Rear OAPD All

1709 PJHRB0080Z Guide, Right Front OAPD All

1710 PJHRB0081Z Guide, Right Rear OAPD All

1711 PJUSB0080Z Spring, Ground OAPD All

1712 PJDFB0025Z Shaft, Pickup Roller OAPD All

1713 PJHRB0445Z Rib, Paper Chute OAPD All

1714 PJDJ06061CZ Bearing OAPD All

1715 PJDJ06121RZ Bearing OAPD All

1716 PJDRB0025Z Roller, Paper Feed OAPD All

1717 PJDGB0058Z Gear 1 OAPD All




1721 PJMDB0037Z Bracket, Gear OAPD All

1722 PJHRB0079Z Arm, Sensor OAPD All

1723 XPL2A10WVW Pin OAPD All

1724 PJUAB0007Z Chassis, Right OAPD All

1725 PJUAB0008Z Chassis, Left OAPD All

1726 PJMDB0036Y Frame, Chassis OAPD All

1727 PJHG351Z Plate, Rubber OAPD All

1728 PJMDB0190Z Plate, Corner OAPD All

1729 PJHRB0521Z Bushing OAPD All

1730 PJYFPMF3M Assembly, Top Cover OAPD All

1731 PJMDB0035Y Paper Chute OAPD All

1732 PJZUPMF3M Assembly, Paper Guide OAPD All

1733 PJZRPMF3M Roller, Pickup OAPD PM All

1734 PJWMPMF3M Clutch OAPD All

1735 PJWQPMF3M Motor OAPD All

1736 PJULC0023Z Bracket, L All

1737 PJULC0022Z Bracket, R All

1738 PJMDB0256Z Bracket, Joint All

1739 PJHRB0684Z Sheet, Bracket All

1740 PJHRC0055Z Sheet, Paper Chute All

1741 PJHRC0176Z Plate, Spacer All

1742 PJHRC0154Z Sheet, Clutch Guide All

150JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 17 2nd Paper Feed Module

U1

U1

U1

17281726

U1

1708

U1

1710

U1

U1

1728

1731

1737V6

1711

1733

1736

1725

1515

U1

1707

1727

1727

1709

1701

U11732

U1

U1

U1

1702

1703

17041705V2

T9

17161410

1717

1306810

1715

8111723

1712

1714

811

1401

V6

1515U1

1713

1724

17111729

811

U1U1

1734

1742

17351721

1719

1720

1718

V3

1730U1

U1

1945

U1

1738

1739

1739

1738U1

1722

U1U1U1

U1

U11741

1740

151JUN 2004Ver. 2.0

UF-9000
DP-180/190
Safety Mark

Ref. No.





1401 PJUAB0024Y Plate, Lower Base OAPD All

1410 PJDJ05011CZ Bearing, C5 OAPD All

1515 PJDSB0024Z Spring, Paper Tray Guide OAPD All

1945 PJWPPMF3M2 PC Board, 2nd Feeder OAPD RTL, PbF All



V2 XTW3+6S Screw All

V3 XWE4 Washer All


152JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 17 2nd Paper Feed Module

U1

U1

U1

17281726

U1

1708

U1

1710

U1

U1

1728

1731

1737V6

1711

1733

1736

1725

1515

U1

1707

1727

1727

1709

1701

U11732

U1

U1

U1

1702

1703

17041705V2

T9

17161410

1717

1306810

1715

8111723

1712

1714

811

1401

V6

1515U1

1713

1724

17111729

811

U1U1

1734

1742

17351721

1719

1720

1718

V3

1730U1

U1

1945

U1

1738

1739

1739

1738U1

1722

U1U1U1

U1

U11741

1740

153JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.17. Paper Tray (2nd Paper Feed Module)

Safety Mark

Ref. No.


1801 PJHRB0338Z Base, Paper Tray OAPD All

1802 PJHRB0340Z Guide, Right Paper Side OAPD All

1803 PJHRB0341Z Guide, Left Paper Side OAPD All

1804 PJHRB0339ZCase, Paper Tray Extension

OAPD All

1805 PJDSB0190Z Spring, Retard Pad OAPD All

1806 PJHRB0344ZIndicator, Orange Paper Level

OAPD All

1807 PJDSB0157Y Spring Friction OAPD All

1808 PJUSB0089Z Spring, Side Guide OAPD All

1809 PJMDB0155Y Lifter, Paper OAPD All

1810 PJHRB0343Z Cover, Lifter OAPD All

1811 PJHRB0447Z Guide, Paper OAPD For DP-180 Except AU

1812 PJZEPMF3M1 Pad, Separation OAPD PM All

1813 PJZE1PMF3M Assembly, Paper Size Knob OAPD All

1814 PJGEC0004Z Sheet, Paper Tray FFor UF-9000/DP-190

AU

1815 PJGEC0005Z Sheet, Paper Tray GFor UF-9000/DP-190

AU

1816 PJGEC0009Z Sheet, Paper Tray HFor UF-9000/DP-190

AU

1817 PJGEC0010Z Sheet, Paper Tray IFor UF-9000/DP-190

AU

1818 PJGFC0012ZLabel, Max. Level Indicator 2

All

1819 PJHGC0004Z Rubber, Separation Pad All

1820 PJHRC0216Z Sheet, 2nd Separation Pad All

1821 PJHGC0005Z Rubber, Paper Size Knob All

1822 PJHRC0056Z Sheet, Paper Size Knob All

1602 PJHSB0007Z Pad, Friction OAPD All

1607 PJDSB0020Z Spring, Stopper OAPD All

1608 PJHRB0034Z Stopper OAPD All

1613 PJDG50133Z Gear, Pinion OAPD All

1614 PJHRB0036Z Rack OAPD All


154JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 18 Paper Tray (2nd Paper Feed Module)

16021817

1809

1810

1810

1608 1607

1819

1807

1806

1807

18031818

1805

1812

1820

1811

18041813

1822

18211815

16141614

1613U8

U8

1811

1802

18081801

1816

1814

155JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.18. PC Boards

Safety Mark

Ref. No.


1901

DZEC103128

PC Board, SC

For UF-9000RTL, PbF

AU

DZEC103111For DP-190RTL, PbF

AU

DZEC103454

For DP-180RTL, PbF

Except AU, AG, AV, YV

DZEC103455 AG

DZEC103456 AV

DZEC103460 YV

1902 PJWPUF9KEM PC Board, Engine Control RTL, PbF All

1903

DZEC102932

PC Board, FXB

For UF-9000RTL, PbF

AU

DZEC103220For DP-190RTL, PbF

AU

DZEC103331 For DP-180RTL, PbF

AL, EB

DZEC103219 Except AL, EB

1905DZEC102978

PC Board, PNL1 RTL, PbFExcept YV

DZEC103469 YV

1906

DZEC102979

PC Board, PNL2

For UF-9000RTL, PbF

AU

DZEC103158For DP-180/190RTL, PbF

All


1910 7UA1810AF11A PC Board, SPC PbF All

1911 7UA1810AS11A PC Board, ADF PbF All

1913 PJJRML0019Z Harness, LSU OAPD All

1914 PJJRML0020Z Harness, Motor OAPD All

1915 PJJRB1027Z Harness, LVPS All

1916 PJJRML0011Z Harness, Low Toner Sensor OAPD All

1917 PJJEC10003YHarness, HVPS (Flat Harness)

OAPD All

1918 PJJEC04002ZHarness, Exit Sensor (Flat Harness)

OAPD All

1919 PJJEC05002ZHarness, Registration Detect Sensor (Flat Harness)

OAPD All

1920 PJJRML0015Z Harness, No Paper Sensor OAPD All

1921 PJJRML0014ZHarness, 2nd Paper Feed Module I/F Board

OAPD All

1922 739909000620Cable, CCD (Flat Harness)

All

1923 737300121950 Cable, USB All

1924 737420001290 Harness, Scanner All

1925 737420001312 Cable, ADF All

1926 737420001300 Harness, PNL All

1927 DZFP001556 Harness, FXB All

1928 DZFP001558 Harness, Speaker All

1929 DZFP001555Cable, ECB (Flat Harness)

All

1930 DZFP001554 Harness, Power Supply All

156JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 19 PC Boards / Harnesses

1925

1949

1734 1735541

554

542

428 540

1923

1924

1922

222

221

1925

SC (1901)

Engine Control (1902)

FXB (1903)

DC (1931)2nd Feeder (1945)

ADF (1911)

SPC (1910)

PNL1 (1905)

PNL2 (1906)

1950

1935

1934

1915 1930 1923 1929 1924 1926 1927

1932

1926 127

1942

1939 1906

1948 1939 1940

1908 1943

1941

1940

1919

1916

1920

1921

1953 1112

1917 822

1914 1006

1320

1951 1952

1929

1928 1927

1918 1913 1113 1930

CN300CN301

CN305CN308 CN304

CN306 CN309

CN002 CN003 CN005

CN001

CN006 CN010

P101

P102

P106

P105

P104

P103

CN143

CN141

CN602

CN600CN601

CN004

CN110CN114

CN008CN017

CN016

CN015CN014

CN009

PA04

PA08

PA05

PA02 PA03

PA01

CN011 CN013 CN007CN018CN012

CN220 CN223 CN234

CN230

CN231CN233

CN232CN302

CN330

CN324

CN328

1932

1933

157JUN 2004Ver. 2.0

UF-9000
DP-180/190
Safety Mark

Ref. No.



1932 DZFP001565 Harness, HD All

1933 DZFP001566 Harness, DC All

1934 DZEC102137 PC Board, FRM8 All







1945 PJWPPMF3M2 PC Board, 2nd Feeder OAPD RTL, PbF All

1948 DZFP001574 Harness, Book-PNL All

1949 PJWLPMF3M Cable, I/F OAPD All

1950 DZFP001567 Harness, MC All

1951 PJJRB1026ZHarness, Exit Solenoid Relay

All

1952 PJJRB1028Z Harness, Termistor Relay All

1953 PJJRML0021Y Harness, Main Motor OAPD All

127 DZDA000047 LCD Module All

221 738902000340 Motor All

222 737430400030 Sensor, Home Detect All

428 737430400020 Sensor, 400mm All

540 737430400010 Sensor, 320mm All

541 738902000331 Motor All

542 737428200050 Sensor, Cover All

554 7UA1810A951B Assembly, Stamp All

822 PJWMP7100MAssembly, Registration Solenoid

OAPD All

1006 L6FALEGK0009 Motor, Fan OAPD All

1112 PJWSP7105MSwitch, Front Door Safety Interlock

OAPD All

1113 PJWS2P7100MSwitch, OPC Drum Unit Interlock

OAPD All

1320 PJWMP7305M Assembly, Pickup Solenoid OAPD All

1734 PJWMPMF3M Clutch OAPD All

1735 PJWQPMF3M Motor OAPD All

158JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 19 PC Boards / Harnesses

1925

1949

1734 1735541

554

542

428 540

1923

1924

1922

222

221

1925

SC (1901)

Engine Control (1902)

FXB (1903)

DC (1931)2nd Feeder (1945)

ADF (1911)

SPC (1910)

PNL1 (1905)

PNL2 (1906)

1950

1935

1934

1915 1930 1923 1929 1924 1926 1927

1932

1926 127

1942

1939 1906

1948 1939 1940

1908 1943

1941

1940

1919

1916

1920

1921

1953 1112

1917 822

1914 1006

1320

1951 1952

1929

1928 1927

1918 1913 1113 1930

CN300CN301

CN305CN308 CN304

CN306 CN309

CN002 CN003 CN005

CN001

CN006 CN010

P101

P102

P106

P105

P104

P103

CN143

CN141

CN602

CN600CN601

CN004

CN110CN114

CN008CN017

CN016

CN015CN014

CN009

PA04

PA08

PA05

PA02 PA03

PA01

CN011 CN013 CN007CN018CN012

CN220 CN223 CN234

CN230

CN231CN233

CN232CN302

CN330

CN324

CN328

1932

1933

159JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.19. Packing and Accessories

Safety Mark

Ref. No.


2001

PJPGB0254Z

Carton Box

For UF-9000 AU

PJPGB0254Y For DP-190 AU

PJPGB0254WFor DP-180

YV

PJPGB0254X Except AU, YV

2002 PJPGB0255Z Carton, Bottom All

2003 PJPGB0256Z Pad, Bottom All

2004 PJPNB0186Z Cushion, Bottom All

2005 PJPNB0187Z Cushion, Rear All

2006 PJPNB0176Z Cushion, Top All

2007 ----- Drum UnitAvailable as Sales Item

2008 ----- TonerAvailable as Sales Item

2009

DZFM000114

Cord, AC Power

For UF-9000/DP-190

AU

DZFM000073 or

For DP-180

AG, AV, EH, EP, ER, YA, YCDZFM000028

DZFM000031 AL

DZFM000076 orAM

DZFM000032

DZFM000064 EB, ES

DZFM000074 orEE

DZFM000030

DZFM000061 YA

DZFM000043YV

DZFM000065

2010

DZFN000050

Cable, Telephone Line

AU, EB, EP, ER, ES, YA, YC, YV

DZFN000069

For DP-180

AG

DZFN000095AL, EB

DZFN000120

DZFN000017 AL

DZFN000096 AM

DZFN000104 AM, AV, EH, ER

DZFN000030 EH

DZFN000078 EE

DZFN000016 EP

2011 PJQMB0137ZOperating Instructions (For Copy & Network Scan Functions)

For UF-9000 AU

2012 PJQMB0138ZOperating Instructions (For Facsimile and Internet Fax/Email)

For UF-9000 AU

2013

PJWACC00001

Software CD

For UF-9000 AU

PJWACC00003 For DP-190 AU

PJWACC00005For DP-180

Except AU, YV

PJWACC00007 YV

160JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 20 Packing and Accessories

2001

2017

2017

2006

2005

2004

2003

2002

625

211

2014

2016

2010

2009

2013

2015

2020

20212022

2008

20192018

2007

2010

2009

2013

2011

2012

2015

2008

2007

For UF-9000

For DP-180/190

161JUN 2004Ver. 2.0

UF-9000
DP-180/190
Safety Mark

Ref. No.


2014 PJQHB0015Z Installation Instructions All

2015PJQTB0262Z

Directory HolderFor UF-9000 AU

PJQTC0027Z For DP-180/190 All

2016 PJPEB0045Z Box, Accessories All

2017 DZRG000003 Joint All

2018

PJQQC0004Z

Quick Guide

For DP-190 AU

For DP-180 YA

PJQQC0005Z

For DP-180

AG, AL, AM, AV, EB, EE, EH, EP

PJQQC0006Z ER

PJQQC0007Z YC

2019 PJWACC00002 Operating Instructions CD For DP-180/190 All

2020

DZFB000010

PTT Plug For DP-180

AL

DZFN000108 AM

DZFN000105 AV

DZFB000001 EH

DZFN000107

ERDZFN000109

DZFN000119

2021

PJQMC0029ZOperating Instructions (For Copy Arabic)

For DP-180

ES

PJQMC0034ZOperating Instructions (For Copy Chinese)

YV

2022 PJQMC0052ZOperating Instructions (For Fax Chinese)

For DP-180 YV

211 92123C003H Cover, Hole All

625 PJKEB0130Z Cover, Rear Paper Tray All

162JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 20 Packing and Accessories

2001

2017

2017

2006

2005

2004

2003

2002

625

211

2014

2016

2010

2009

2013

2015

2020

20212022

2008

20192018

2007

2010

2009

2013

2011

2012

2015

2008

2007

For UF-9000

For DP-180/190

163JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.20. Printer Controller Module for PCL6

Safety Mark

Ref. No.


2101 DZRB000143 Carton Box All

2102DZHP009971

Software CDFor UF-9000/DP-190

AU

DZHP010345 For DP-180 Except AU

2103 DZSM000795 Installation Instructions All

2104 DZSM000756Installation Instructions (Expansion F-ROM Board)

For DP-180 Except AU

708 DZJH000084 Support, Locking For DP-180 Except AU

1934 DZEC102137 PC Board, FRM8 For DP-180 Except AU


164JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 21 Printer Controller Module for PCL6

2101

2102

1935

2103

2104

1934

708

165JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.21. Printer Controller Module for PS/PCL6

Safety Mark

Ref. No.


2201DZHP009973

Software CD

For UF-9000/DP-190

AU

DZHP010343 For DP-180 Except AU


708 DZJH000084 Support, Locking For DP-180 Except AU

1934 DZEC102137 PC Board, FRM8 For DP-180 Except AU



2104 DZSM000756Installation Instructions (Expansion F-ROM Board)

For DP-180 Except AU

166JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 22 Printer Controller Module for PS/PCL6

21012201

1935

22022104

1934

708

167JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.22. 2nd Paper Feed Module Packing and Accessories

Safety Mark

Ref. No.


2301PJPGB0230Z

Carton BoxAU, YV

PJPGB0230Y For DP-180 Except AU, YV

2302 PJPNB0154Z Cushion, Front All

2303 PJPNB0155Z Cushion, Rear All

2304 PJPNB0082Z Cushion, Inner OAPD All

2305 PJHRB0701Z Cushion, Leg All

2306 PJQMB0132Z Installation Instructions All

1736 PJULC0023Z Bracket, L All

1737 PJULC0022Z Bracket, R All

1738 PJMDB0256Z Bracket, Joint All

1739 PJHRB0684Z Sheet, Bracket All



168JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 23 2nd Paper Feed Module Packing and Accessories

2303

2306

2305

V6

1738, 1739

2304

2302

2301

U1

17361737

169JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.23. Hard Disk Drive Unit

Safety Mark

Ref. No.



2402 DZRB000750 Cushion All

2403 DZJK000057 Edge Saddle All




706 N3CABRD00005 HDD Unit All

707 DZJC000389 Bracket, HDD All


1932 DZFP001565 Harness, HD All

1933 DZFP001566 Harness, DC All

L9 XTB3+4F Screw All

V5 XTW3+6LFC Screw All

170JUN 2004Ver. 2.0

UF-9000
DP-180/190
A C D EB

8

1

3

4

5

6

7

222

Fig. 24 Hard Disk Drive Unit

2406

2405

V5

L9

706

2402

2401

707

1931

2404

1932

1933

2403

171JUN 2004Ver. 2.0

UF-9000
DP-180/190
5.24. Hardware Identification Template

Part No. Figure RemarkRef. No.

ScrewXYN3+F53F

ScrewXTB3+8GF10

ScrewXTW3+8LP3

ScrewXTW26+8ST8

ScrewXTW3+8ST9

ScrewXTW3+6LU1

ScrewXYC3+FF8CU3

ScrewXTW3+12SU4

ScrewXTW3+12SFZU5

ScrewPJNEB0003YU7

ScrewXTB3+8J19

ScrewXTW3+8PP8

ScrewXTW3+8LFNH8

ScrewXTB3+4FL9

E-Ring21070121706447

Washer, StarXWC3BG8

E-RingXUC4VW-VU6

ScrewXTW3+U8SU8

172JUN 2004Ver. 2.0

UF-9000
DP-180/190
WasherXWE4V3

ScrewXTW3+8PFNV7

ScrewXTW4+16PV8

ScrewXTW3+6LFNV9

ScrewXTS3+8JW1

ScrewDZZSP29011W2

ScrewXTB2+12JW4

ScrewXSN2+10FNW5

ScrewXTW4+8LFNY11

ScrewXTW3+6LFCV5

ScrewXTB3+8JFNV6

ScrewPJNAC0003ZW7

ScrewXTN3+8JFNW8

ScrewXTW3+6SV2

ScrewXSN3+4U9

ScrewXYC3+FF6V1

Part No. Figure RemarkRef. No.

173JUN 2004Ver. 2.0

UF-9000
DP-180/190
6 Alphanumerical Parts List

Alphanumerical Parts ListPart Number Part Name Ref. No. Supplier PM Destination

21070121706 E-Ring 447 All

735109001050 Core 305 All

737300121950 Cable, USB 1923 All

737420001290 Harness, Scanner 1924 All

737420001300 Harness, PNL 1926 All

737420001312 Cable, ADF 1925 All

737428200050 Sensor, Cover 542 All

737430400010 Sensor, 320mm 540 All

737430400020 Sensor, 400mm 428 All

737430400030 Sensor, Home Detect 222 All

738902000331 Motor 541 All

738902000340 Motor 221 All

738903000110 Lamp, Scanning 303 All

739909000620 Cable, CCD (Flat Harness) 1922 All

783309000120 E-Ring 224 All

7UA1810A631B Assembly, Pickup 449 All

7UA1810A681B Assembly, Scanner Cover 219 All

7UA1810A721B Assembly, CCD Module (For UF-9000/DP-190) 301 AU

7UA1810A722B Assembly, CCD Module (DP-180) 301 Except AU

7UA1810A951B Assembly, Stamp 554 All

7UA1810AF11A PC Board, SPC 1910 All

7UA1810AS11A PC Board, ADF 1911 All

7UZFFA02501B ADF Unit 442 All

81123D148H Gear, 12T 422 All

81123D150H Gear, 23T 416 All

81123D156H Gear, 24T 434 All

81133D040H Spring, Tension 426 All

81141C001H Magnetic 535 All

81150C008H Switch, Magnetic 201 All

81158D013H Rivet, Snap 551 All

81325D113H Cover, Inverter 306 All

91100D001H Shaft 509 All

91102B002H Plate, Rear Attachment 526 All

91102C002H Plate, Front Attachment 522 All

91102C004H Plate, Reading 518 All

91102D002H Spring, Ground 517 All

91102D004H Plate, ADF Roller Fix 409 All

91102D005H Plate, Roll Fix 407 All

91102D007H Spring, Roller Pressure 506 All

91102D011H Holder, Pulley 209 All

91102D012H Sheet, Holder 208 All

91110D002H Shaft, ADF 418 All

91110D003H Shaft, Pickup 415 All

91110D007H Pin 425 All

91123A002H Frame, ADF 511 All

91123A003H Cover, Frame 510 All

91123A004H Base, ADF 405 All

91123D001H Roll, Pinch 508 All

91123D002H Knob, Paper Transport 525 All

91123D003H Arm, Sensor 507 All

174JUN 2004Ver. 2.0

UF-9000
DP-180/190
91123D004H Base, Pad 546 All

91123D005H Cover, Tray 435 All

91123D006H Level, Sensor 406 All

91123D008H Rack, Guide 433 All

91123D009H Gear, 18/45T 528 All

91123D010H Gear, 30T 533 All

91123D012H Gear, 33T 521 All

91123D013H Gear, 48T 527 All

91123D014H Gear, 26T 531 All

91123D015H Gear, 18/40T 529 All

91123D021H Base, Pickup 412 All

91123D022H Arm, Stopper 413 All

91123D023H Shutter, Left 421 All

91123D024H Shutter, Right 420 All

91123D025H Roller 408 All

91123D034H Pulley, Idle 210 All

91123D035H Collar 206 All

91123D042H Base, Dummy Hinge 439 All

91123D043H Hinge, Upper Dummy 443 All

91123D053H Hook, Top Cover 524 All

91127C001H Roller, Feed 516 PM All

91127C002H Roller, Exit 519 All

91127C003H Roller, ADF 417 PM All

91127C004H Roller, Pickup 414 PM All

91127D001H Roll, Exit 503 All

91127D002H Rubber, Separation 547 PM All

91129D004H Sheet, Pad 548 All

91129D008H Sheet, Guide 534 All

91129D009H Sheet, Pressure 549 All

91129D010H Sheet, Trace 427 All

91133D001H Spring, Exit Roller 504 All



91133D005H Spring, Reading Plate 532 All

91133D006H Spring, Torsion 550 All

91134C001H Hinge, ADF 403 All

91134D001H Sheet, Pickup 515 All

91134D002H Brush, Antistatic 539 All

91137D002H Screw, Dummy Hinge 440 All

91142D002H Bushing, D6 537 All

91192D001H Plate, Motor Attachment 512 All

92102C001H Plate, Motor Fix 204 All

92102C002H Cover, Main Board 216 All

92102C003H Base, Cover 217 All

92102C007H Plate, Metal 215 All

92102D005H Spring, Plate 223 All

92102D007H Plate, FFC Set 226 All

92102D008H Plate, Seal 227 All

92102D009H Plate, Core Set 228 All

92110C001H Shaft, IR 202 All

92110D001H Shaft, Transfer 419 All

92123A001H Frame, IR Base 212 All

92123A004H Base, ADF 501 All


175JUN 2004Ver. 2.0

UF-9000
DP-180/190
92123A005H Cover, Top ADF 401 All

92123A006H Guide, Document 429 All

92123A007H Cover, Rear ADF 402 All

92123B001H Guide, Extend Document 430 All

92123C001H Guide, Rear 432 All

92123C002H Guide, Front 431 All

92123C003H Cover, Hole 211 All

92123C004H Cover, Harness 218 All

92123D001H Gear, 60T/P16T 205 All

92123D002H Gear, 32/15T 530 All

92123D003H Gear, 20T 423 All

92123D004H Gear, 23S 410 All

92123D005H Gear, 19S 411 All

92123D006H Holder, Pickup Sheet 514 All

92123D011H Cover, Dummy Hinge 441 All

92123D012H Stud, Gap 520 All

92123D014H Lib, Fix Plate 523 All

92123D015H Cover, Protect 505 All

92125D001H Sheet, Tray 436 All

92125D006H Seal, CCD Harness 213 All

92125D007H Label, Max. Capacity Indicator 437 All

92129D001H Sheet, White Reference 536 All

92129D002H Sheet, Protect Cover 502 All

92129D004H Sheet, Gap Limit 538 All

92129D008H Sheet, Plate 552 All

92129D010H Seal, Screw 225 All

92129D021H Gasket 1 230 All

92129D022H Gasket 2 231 All

92130D001H Pad, Scanning 404 All

92130D002H Sponge 214 All

92130D003H Cushion, Stopper 444 All

92130D004H Cushion, Pick-up 445 All

92142D001H Clutch, One Way 424 All

92143D001H Belt 203 All

A4DP3L000003 Lamp, Halogen (For DP-190) 1209 AU

A4DP7K000002 Lamp, Halogen (For DP-180) 1209 Except AU

CR2032 Battery 128 All

DZDA000047 LCD Module 127 All

DZDR000014 Speaker 631 All

DZDU000025 Handset 626 Except AK

DZDU000027 Handset 626 AK

DZEC101941 PC Board, SRU 1946 AU

DZEC102137 PC Board, FRM8 (For DP-180) 1934 Except AU

DZEC102525 PC Board, SRU 1946 AK

DZEC102526 PC Board, SRU 1946 AT

DZEC102527 PC Board, SRU 1946 YW

DZEC102566 PC Board, SRU 1946 YC

DZEC102932 PC Board, FXB (For UF-9000) 1903 AU

DZEC102978 PC Board, PNL1 1905 Except YV

DZEC102979 PC Board, PNL2 (For UF-9000) 1906 AU

DZEC102980 PC Board, PNL3 1907 All




176JUN 2004Ver. 2.0

UF-9000
DP-180/190
DZEC103051 PC Board, DC 1931 All

DZEC103111 PC Board, SC (For DP-190) 1901 AU

DZEC103128 PC Board, SC (For UF-9000) 1901 AU

DZEC103158 PC Board, PNL2 (For DP-180/190) 1906 All

DZEC103219 PC Board, FXB (For DP-180) 1903 Except AL, EB

DZEC103220 PC Board, FXB (For DP-190) 1903 AU

DZEC103331 PC Board, FXB (For DP-180) 1903 AL, EB

DZEC103454 PC Board, SC (For DP-180) 1901Except AU, AG, AV, YV

DZEC103455 PC Board, SC (For DP-180) 1901 AG

DZEC103456 PC Board, SC (For DP-180) 1901 AV

DZEC103460 PC Board, SC (For DP-180) 1901 YV

DZEC103469 PC Board, PNL1 1905 YV

DZFB000001 PTT Plug (For DP-180) 2020 EH

DZFB000010 PTT Plug (For DP-180) 2020 AL

DZFM000028 Cord, AC Power (For DP-180) 2009AG, AV, EH, EP, ER, YA, YC

DZFM000030 Cord, AC Power (For DP-180) 2009 EE

DZFM000031 Cord, AC Power (For DP-180) 2009 AL

DZFM000032 Cord, AC Power (For DP-180) 2009 AM

DZFM000043 Cord, AC Power (For DP-180) 2009 YV

DZFM000061 Cord, AC Power (For DP-180) 2009 YA

DZFM000064 Cord, AC Power (For DP-180) 2009 EB, ES

DZFM000065 Cord, AC Power (For DP-180) 2009 YV

DZFM000073 Cord, AC Power (For DP-180) 2009AG, AV, EH, EP, ER, YA, YC

DZFM000074 Cord, AC Power (For DP-180) 2009 EE

DZFM000076 Cord, AC Power (For DP-180) 2009 AM

DZFM000114 Cord, AC Power (For UF-9000/DP-190) 2009 AU

DZFN000016 Cable, Telephone Line (For DP-180) 2010 EP

DZFN000017 Cable, Telephone Line (For DP-180) 2010 AL

DZFN000030 Cable, Telephone Line (For DP-180) 2010 EH

DZFN000050 Cable, Telephone Line 2010AU, EB, EP, ER, ES, YA, YC, YV

DZFN000060 Cord, Handset 629 All

DZFN000069 Cable, Telephone Line (For DP-180) 2010 AG

DZFN000078 Cable, Telephone Line (For DP-180) 2010 EE

DZFN000082 Cord, Cradle 630 Except AK

DZFN000095 Cable, Telephone Line (For DP-180) 2010 AL, EB

DZFN000096 Cable, Telephone Line (For DP-180) 2010 AM

DZFN000104 Cable, Telephone Line (For DP-180) 2010 AM, AV, EH, ER

DZFN000105 PTT Plug (For DP-180) 2020 AV

DZFN000107 PTT Plug (For DP-180) 2020 ER

DZFN000108 PTT Plug (For DP-180) 2020 AM


DZFN000115 Cord, Cradle 630 AK


DZFN000120 Cable, Telephone Line (For DP-180) 2010 AL, EB

DZFP001548 Harness, PNL2-PNL3_5PIN 1943 All

DZFP001554 Harness, Power Supply 1930 All

DZFP001555 Cable, ECB (Flat Harness) 1929 All

DZFP001556 Harness, FXB 1927 All

DZFP001558 Harness, Speaker 1928 All



177JUN 2004Ver. 2.0

UF-9000
DP-180/190



DZFP001565 Harness, HD 1932 All

DZFP001566 Harness, DC 1933 All

DZFP001567 Harness, MC 1950 All

DZFP001574 Harness, Book-PNL 1948 All

DZHP009971 Software CD For (UF-9000/DP-190) 2102 AU

DZHP009973 Software CD (UF-9000/DP-190) 2201 AU

DZHP010343 Software CD (For DP-180) 2201 Except AU

DZHP010345 Software CD (For DP-180) 2102 Except AU

DZHT000004 Stamp Head 553 Except AU

DZHT000027 Stamp Head 553 AU

DZJC000389 Bracket, HDD 707 All

DZJC000390 Bracket, Counter 710 All

DZJE000738 Cradle, Upper 627 AU

DZJE000740 Cradle, Lower 628 AU

DZJF000462 Guide, Flash Memory Card 704 All

DZJH000084 Support, Locking (For DP-180) 708 Except AU

DZJK000004 Clamp 2405 All

DZJK000057 Edge Saddle 2403 All




DZKB000637 Key, Print 112 All

DZKB000640 Key, B 109 All

DZKB000641 Key, Reset 106 All

DZKB000760 Key, Function 107 All

DZKB000762 Key, Stop 105 All

DZKB000796 Key, Start 104 All

DZKB000803 Key, Touch3 113 All

DZKB000858 Key, Scan/File 111 All

DZKB000862 Key, Copy 110 All

DZKB000922 Key, A 108 All

DZMA000260 Cradle, Upper 627 Except AU

DZMA000269 Cradle, Lower 628 Except AU

DZMA003267 Cover, Flash Memory Card 621 All

DZNK005395 Label, Laser Caution 632 All

DZRB000143 Carton Box 2101 All

DZRB000733 Carton Box 2401 All

DZRB000750 Cushion 2402 All

DZRG000003 Joint 2017 All

DZSM000756Installation Instructions (Expansion F-ROM Board, For DP-180)

2104 Except AU

DZSM000795 Installation Instructions 2103 All



DZTK000002 Counter, Mechanical 711 All

DZZSP29011 Screw W2 All

FFPTE2650 Label, Energy Star 635 All

J0KF00000015 Ferrite Core 1115 All

J0KF00000046 Ferrite Core 1115 All

K5AT281613 Core 1116 OAPD All


178JUN 2004Ver. 2.0

UF-9000
DP-180/190
L2AA00000088 Thermistor 1229 All

L2AA00000090 Thermostat 1204 All

L6CCKGEK0003 Motor 907 OAPD All

L6FALEGK0009 Motor, Fan 1006 OAPD All

L9DAEJ000001 Lamp, Halogen (For UF-9000) 1209 OAPD AU

N0GG4E000002 HVPS 1005 OAPD All

N3CABRD00005 HDD Unit 706 All

PJBAB0011Z Hook 606 OAPD All

PJBAB0020Z Holder, LCD 122 All

PJBCB0016Z Key, Contrast 116 All

PJBCB0017Z Key, Fax/Email 114 All

PJBCB0018Z Key, Zoom 117 All

PJBCB0019X Key, 1 (For DP-180) 118 AV

PJBCB0019Y Key, 1 (For DP-180/190) 118 Except AV

PJBCB0019Z Key, 1 (For UF-9000) 118 AU

PJBCB0020W Key, 2 119 AV

PJBCB0020X Key, 2 (For DP-180) 119 AG

PJBCB0020Y Key, 2 (For DP-180/190) 119 Except AG, AV

PJBCB0020Z Key, 2 (For UF-9000) 119 AU

PJBCB0021Z Key, 3 120 All

PJBCB0022Z Key, Ten 115 All

PJBCB0023Z Key, C (For DP-180/190) 130 All

PJDFB0008Z Shaft, Roller 613 OAPD All

PJDFB0009Z Shaft, A/D Roller 1404 OAPD All

PJDFB0025Z Shaft, Pickup Roller 1712 OAPD All

PJDFB0122Z Shaft, Fuser Drive 1201 OAPD All

PJDFB0163Z Shaft, Pickup Roller 1311 OAPD All

PJDG50133Z Gear, Pinion 1613 OAPD All

PJDGB0021Z Gear, Heat Roller 1208 OAPD All

PJDGB0023Z Gear, Z24 Fuser 1202 OAPD All

PJDGB0024Z Gear, Z21 Fuser 1102 OAPD All

PJDGB0025Z Gear, Internal 1104 OAPD All

PJDGB0026Z Gear, Z36 Upper Exit Roller Drive 1103 OAPD All

PJDGB0027Z Gear, Black Ratchet 1105 OAPD All

PJDGB0028Z Gear, Ratchet 806 OAPD All

PJDGB0029Z Gear, Planetary 809 OAPD All

PJDGB0030Z Gear, A/D Unit Union 1411 OAPD All

PJDGB0038Z Gear, Registration Roller 1304 OAPD All

PJDGB0039Z Gear, Paper Feed Roller 1307 OAPD All

PJDGB0040Z Gear, Pickup Internal 1301 OAPD All

PJDGB0041Z Gear, Pickup Arm 1302 OAPD All

PJDGB0042Z Gear, Registration Internal 808 OAPD All

PJDGB0043Z Gear, Registration Arm 807 OAPD All

PJDGB0047Z Gear, OPC B 901 OAPD All

PJDGB0048Z Gear, OPC A 902 OAPD All

PJDGB0049Z Gear, Fuser 903 OAPD All

PJDGB0051Z Gear, Fuser Drive 812 OAPD All

PJDGB0052Z Gear, ADU Drive 801 OAPD All

PJDGB0056Z Gear, Registration A 904 OAPD All

PJDGB0057Z Gear, Transfer 1505 OAPD All

PJDGB0058Z Gear 1 1717 OAPD All




179JUN 2004Ver. 2.0

UF-9000
DP-180/190

PJDGB0069Z Gear, Registration B 905 OAPD All

PJDGB0070Z Gear, Registration Drive 802 OAPD All

PJDGB0071Z Gear, Double Teeth 804 OAPD All

PJDGB0072Z Gear, Idle Z19 803 OAPD All

PJDGB0073Z Gear, Idle Z14 805 OAPD All

PJDGB0203Z Gear, Upper Exit Roller Drive 1106 OAPD All

PJDGB0204Z Gear, Intermediate Fuser 814 OAPD All

PJDJ05011CZ Bearing, C5 1410 OAPD All

PJDJ05041RZ Bearing, R5 1306 OAPD All

PJDJ06061CZ Bearing 1714 OAPD All

PJDJ06121RZ Bearing 1715 OAPD All

PJDJB0008Z Bushing, Left Heat Roller 1206 OAPD All

PJDJB0009Z Bushing, Right Heat Roller 1207 OAPD All

PJDJB0010Z Bushing, Pressure Roller 1214 OAPD All

PJDJB0019Z Bushing 1309 OAPD All

PJDJB0020Z Bearing, U 1506 OAPD All

PJDPB0001Z Solenoid, Upper Exit Roller with Plunger 1110 OAPD All

PJDRA0051Z Roller, Pinch 1705 OAPD All

PJDRB0014Z Shaft, ADU Registration Roller 1409 OAPD All

PJDRB0017Z Roller, Pinch 610 OAPD All

PJDRB0018Z Roller, ADU Pinch 1403 OAPD All

PJDRB0021Z Roller, Registration 1303 OAPD All

PJDRB0022Z Roller, Paper Feed 1305 OAPD All

PJDRB0025Z Roller, Paper Feed 1716 OAPD All

PJDRB0059Z Roller, Sub 1009 OAPD All

PJDRB0081Z Roller, Bias Transfer 1503 OAPD PM All

PJDRB0091Z Roller, Heat 1205 OAPD All

PJDRB0092Z Roller, Pressure 1216 OAPD All

PJDRB0093Z Roller, Cleaning 611 OAPD All

PJDSB0008Z Spring, Right OPC 1512 OAPD All

PJDSB0009Y Spring, OPC 1003 OAPD All

PJDSB0010Z Spring, Right Registration 1514 OAPD All

PJDSB0015Z Spring, Paper Jam Sensor Lever 1213 OAPD All

PJDSB0016Z Spring, Ratchet 1107 OAPD All

PJDSB0017Z Spring 1412 OAPD All

PJDSB0018Z Spring, Pinch Roller A 1217 OAPD All


PJDSB0020Z Spring, Stopper 1607 OAPD All

PJDSB0024Z Spring, Paper Tray Guide 1515 OAPD All

PJDSB0026Z Spring, Left OPC 1511 OAPD All

PJDSB0033Z Spring, Grid 1001 OAPD All

PJDSB0034Z Spring, Pinch Roller 608 OAPD All

PJDSB0035Z Spring, Registration 1417 OAPD All

PJDSB0039Z Spring, Gear Tension 813 OAPD All

PJDSB0040Z Spring, Transfer 1502 OAPD All

PJDSB0041Z Spring, Pinch Roller 1405 OAPD All

PJDSB0043Z Spring, Left Registration 1513 OAPD All


PJDSB0145Z Spring, Cleaning Roller 609 OAPD All

PJDSB0148Z Spring, Charge 1002 OAPD All

PJDSB0149Z Spring, Developer 1004 OAPD All

PJDSB0157Y Spring Friction 1807 OAPD All


180JUN 2004Ver. 2.0

UF-9000
DP-180/190
PJDSB0179Z Spring, Retard Pad 1603 OAPD All

PJDSB0190Z Spring, Retard Pad 1805 OAPD All

PJDSB0205Z Spring, Pressure Roller 1215 OAPD All

PJDSB0206Z Spring, Separator 1223 OAPD All

PJDSB0207Z Spring, Pickup Holder 1312 OAPD All

PJDSB0208Z Spring, Dust Scraper 1314 OAPD All

PJDSB0210Y Spring, Friction 1606 OAPD All

PJDSB0211Z Spring, Pickup 815 OAPD All

PJGEC0002Z Sheet, Paper Tray A (For UF-9000/DP-190) 1617 AU

PJGEC0003Z Sheet, Paper Tray B (For UF-9000/DP-190) 1618 AU

PJGEC0004Z Sheet, Paper Tray F (For UF-9000/DP-190) 1814 AU

PJGEC0005Z Sheet, Paper Tray G (For UF-9000/DP-190) 1815 AU

PJGEC0006Z Sheet, Paper Tray C (For UF-9000/DP-190) 1619 AU

PJGEC0007Z Sheet, Paper Tray D (For UF-9000/DP-190) 1620 AU

PJGEC0008Z Sheet, Paper Tray E (For UF-9000/DP-190) 1621 AU

PJGEC0009Z Sheet, Paper Tray H (For UF-9000/DP-190) 1816 AU

PJGEC0010Z Sheet, Paper Tray I (For UF-9000/DP-190) 1817 AU

PJGFC0011Z Label, Max. Level Indicator 1 1622 All

PJGFC0012Z Label, Max. Level Indicator 2 1818 All

PJGKB0087Z LCD Window (For UF-9000) 124 AU

PJGKB0088U Sheet, Panel 1 (For DP-180) 125Except AU, AG, AV, YV

PJGKB0088W Sheet, Panel 1 (For DP-180) 125 YV

PJGKB0088X Sheet, Panel 1 (For DP-180) 125 AV

PJGKB0088Y Sheet, Panel 1 (For DP-180) 125 AG

PJGKB0088Z Sheet, Panel 1 (For UF-9000/DP-190) 125 AU

PJGKB0089V Sheet, Panel 2 (For DP-180) 126 YV

PJGKB0089W Sheet, Panel 2 (For DP-180) 126 AV

PJGKB0089X Sheet, Panel 2 (For DP-180) 126 AG

PJGKB0089Y Sheet, Panel 2 (For DP-180/190) 126Except AG, AV, YV

PJGKB0089Z Sheet, Panel 2 (For UF-9000) 126 AU

PJGKB0107V LCD Window (For DP-180) 124 YV

PJGKB0107W LCD Window (For DP-180) 124 AV

PJGKB0107X LCD Window (For DP-180) 124 AG

PJGKB0107Y LCD Window (For DP-190) 124 AU

PJGKB0107Z LCD Window (For DP-180) 124Except AU, AG, AV, YV

PJGPB0011W Cover, Panel (For DP-180) 103 YV

PJGPB0011X Cover, Panel (For DP-180) 103 AV

PJGPB0011Y Cover, Panel (For DP-180) 103 AG

PJGPB0011Z Cover, Panel (For DP-180) 103Except AG, AV, YV

PJHE5065Z Screw 1022 OAPD All

PJHG351Z Plate, Rubber 1727 OAPD All

PJHGC0004Z Rubber, Separation Pad 1819 All

PJHGC0005Z Rubber, Paper Size Knob 1821 All

PJHR9224Z Separator 1225 OAPD All

PJHRA0316Z Guard, Edge 817 OAPD All

PJHRB0029Y Assembly, Paper Tray Base 1609 OAPD All

PJHRB0030Z Tray, Paper Tray Extension 1610 OAPD All

PJHRB0031Z Guide, Right Paper Side 1604 OAPD All

PJHRB0032Z Guide, Left Paper Side 1605 OAPD All

PJHRB0033Z Knob, Paper Size 1611 OAPD All


181JUN 2004Ver. 2.0

UF-9000
DP-180/190
PJHRB0034Z Stopper 1608 OAPD All

PJHRB0036Z Rack 1614 OAPD All

PJHRB0037Z Arm, Right Pressure 1508 OAPD All

PJHRB0038Z Arm, Left Pressure 1507 OAPD All

PJHRB0045Z Rack, Guide 604 OAPD All

PJHRB0046Z Gear, Paper Guide Pinion 605 OAPD All

PJHRB0070Z Wheel, Drive 1308 OAPD All

PJHRB0075Z Lever, Registration Sensor 1415 OAPD All

PJHRB0076Z Lever, Paper Detect Sensor 1416 OAPD All

PJHRB0078Z Bushing 1504 OAPD All

PJHRB0079Z Arm, Sensor 1722 OAPD All

PJHRB0080Z Guide, Right Front 1709 OAPD All

PJHRB0081Z Guide, Right Rear 1710 OAPD All

PJHRB0082Z Guide, Left Front 1707 OAPD All

PJHRB0083Z Guide, Left Rear 1708 OAPD All

PJHRB0307Z Indicator, Orange Paper Level 1612 OAPD All

PJHRB0320Z Lever, No Paper Sensor 1414 OAPD All

PJHRB0324Z Holder, Transfer Roller 1501 OAPD All

PJHRB0327Z Clamp 824 OAPD All

PJHRB0338Z Base, Paper Tray 1801 OAPD All

PJHRB0339Z Case, Paper Tray Extension 1804 OAPD All

PJHRB0340Z Guide, Right Paper Side 1802 OAPD All

PJHRB0341Z Guide, Left Paper Side 1803 OAPD All

PJHRB0343Z Cover, Lifter 1810 OAPD All

PJHRB0344Z Indicator, Orange Paper Level 1806 OAPD All

PJHRB0445Z Rib, Paper Chute 1713 OAPD All

PJHRB0447Z Guide, Paper (For DP-180) 1811 OAPD Except AU

PJHRB0476Z Adapter, Retard 1616 OAPD All

PJHRB0521Z Bushing 1729 OAPD All

PJHRB0567Z Support, Right Paper 602 All

PJHRB0568Z Support, Left Paper 603 All

PJHRB0635Z Holder, Heat Roller 1221 OAPD All

PJHRB0636Z Base, Fuser Unit 1212 OAPD All

PJHRB0637Z Lever, Paper Jam Sensor 1220 OAPD All

PJHRB0638Z Cover, Left Fuser 1224 OAPD All

PJHRB0640Z Adapter, Pickup Holder 1313 OAPD All

PJHRB0659Y Guide, Exit Paper 1019 All

PJHRB0684Z Sheet, Bracket 1739 All

PJHRB0701Z Cushion, Leg 2305 All

PJHRC0051Z Sheet, Separation Pad 1623 All

PJHRC0216Z Sheet, 2nd Separation Pad 1820 All

PJHRC0055Z Sheet, Paper Chute 1740 All

PJHRC0056Z Sheet, Paper Size Knob 1822 All

PJHRC0154Z Sheet, Clutch Guide 1742 All

PJHRC0176Z Plate, Spacer 1741 All

PJHSB0007Z Pad, Friction 1602 OAPD All

PJHXB0019Z Sheet, Insulated 123 All

PJHXC0001Z Sheet, Protect 129 All

PJJEC04002Z Harness, Exit Sensor (Flat Harness) 1918 OAPD All

PJJEC05002ZHarness, Registration Detect Sensor (Flat Harness)

1919 OAPD All

PJJEC10003Y Harness, HVPS (Flat Harness) 1917 OAPD All

PJJRB1025Y Cable, Fuser 1219 OAPD All


182JUN 2004Ver. 2.0

UF-9000
DP-180/190
PJJRB1026Z Harness, Exit Solenoid Relay 1951 All

PJJRB1027Z Harness, LVPS 1915 All

PJJRB1028Z Harness, Termistor Relay 1952 All

PJJRML0011Z Harness, Low Toner Sensor 1916 OAPD All

PJJRML0014Z Harness, 2nd Paper Feed Module I/F Board 1921 OAPD All

PJJRML0015Z Harness, No Paper Sensor 1920 OAPD All

PJJRML0019Z Harness, LSU 1913 OAPD All

PJJRML0020Z Harness, Motor 1914 OAPD All

PJJRML0021Y Harness, Main Motor 1953 OAPD All

PJJTC0002Z Cable, Ground 826 All

PJJTCC014Z Cable 1413 OAPD All

PJKEB0019Z Cover, Front 1701 OAPD All

PJKEB0081X Cover, Front (For DP-180) 601 Except AU

PJKEB0081Y Cover, Front (For DP-190) 601 AU

PJKEB0081Z Cover, Front (For UF-9000) 601 AU

PJKEB0097Z Cover, Right 1702 All

PJKEB0098Z Cover, Left 1703 All

PJKEB0110Z Cover, Right Side 615 All

PJKEB0111Z Cover, Left Side 616 All

PJKEB0112Z Cover, Rear 617 All

PJKEB0113Z Cover, Top 623 All

PJKEB0114Z Tray, Sub Paper 624 All

PJKEB0115Z Base, Panel 101 All

PJKEB0116Z Cover , Right Leg 618 All

PJKEB0117Z Cover, Left Leg 619 All

PJKEB0118Z Cover, PCB 620 All

PJKEB0120Z Lamp, Doing 121 All

PJKEB0130Z Cover, Rear Paper Tray 625 All

PJKKB0001Z Holder, Battery 102 All

PJMCB0068Z Plate, Ground 2 1517 OAPD All

PJMCB0070Z Plate, Ground 1 1516 OAPD All

PJMDB0018Z Plate, Lead Wire 1203 OAPD All

PJMDB0019Y Ground, Fuser 1218 OAPD All

PJMDB0020Z Plate, ADU Pinch Roller 1402 OAPD All

PJMDB0026Y Lifter, Paper 1601 OAPD All

PJMDB0035Y Paper Chute 1731 OAPD All

PJMDB0036Y Frame, Chassis 1726 OAPD All

PJMDB0037Z Bracket, Gear 1721 OAPD All

PJMDB0155Y Lifter, Paper 1809 OAPD All

PJMDB0156Z Clamp 713 OAPD All

PJMDB0190Z Plate, Corner 1728 OAPD All

PJMDB0253Z Plate, Separator 1222 OAPD All

PJMDB0256Z Bracket, Joint 1738 All

PJMDB0257Y Plate, Lead Wire 1210 OAPD All

PJMDB0258Z Stay, Rear 1014 All

PJMDB0259Z Base, Right Side 819 All

PJMDB0260Z Base, Left Side 1015 All

PJMDB0261Z Bracket, Right Side 820 All

PJMDB0262Z Bracket, Left Side 1016 All

PJMDB0263Z Bracket Left Rear 1017 All

PJMDB0264Z Bracket, Right Rear 1018 All

PJMDB0286Z Base, Rear PC Board 703 All

PJMDB0287Z Base, SC 702 All


183JUN 2004Ver. 2.0

UF-9000
DP-180/190
PJMDB0288Z Cover, SC 701 All

PJMDB0289Z Bracket, Side Cover B 1012 All

PJMDB0290Z Bracket, Left Side Cover 1013 All

PJMDB0291Z Bracket, Side Cover A 1011 All

PJMDB0292Z Bracket, Right Side Cover 818 All

PJMDB0316Z Plate, Cover 634 All

PJNAC0003Z Screw W7 All

PJNEB0003Y Screw U7 OAPD All

PJNEB0008Z Screw 1007 OAPD All

PJNW317Z Poly Slider 1406 OAPD All

PJNW410Z Washer 1407 OAPD All

PJNW4111Z Washer, Plastic 810 OAPD All

PJNW525Z Spacer 811 OAPD All

PJNW620Z Washer 906 OAPD All

PJNW721Z Poly Slider 1108 OAPD All

PJNW820Z Washer, Plastic 1317 OAPD All

PJPEB0045Z Box, Accessories 2016 All

PJPGB0230Y Carton Box (For DP-180) 2301 Except AU, YV

PJPGB0230Z Carton Box 2301 AU, YV

PJPGB0254W Carton Box (For DP-180) 2001 YV

PJPGB0254X Carton Box (For DP-180) 2001 Except AU, YV

PJPGB0254Y Carton Box (For DP-190) 2001 AU

PJPGB0254Z Carton Box (For UF-9000) 2001 AU

PJPGB0255Z Carton, Bottom 2002 All

PJPGB0256Z Pad, Bottom 2003 All

PJPNB0082Z Cushion, Inner 2304 OAPD All

PJPNB0154Z Cushion, Front 2302 All

PJPNB0155Z Cushion, Rear 2303 All

PJPNB0176Z Cushion, Top 2006 All

PJPNB0186Z Cushion, Bottom 2004 All

PJPNB0187Z Cushion, Rear 2005 All

PJQHB0015Z Installation Instructions 2014 All

PJQMB0132Z Installation Instructions 2306 All

PJQMB0137ZOperating Instructions (For Copy & Network Scan Functions, For UF-9000)

2011 AU

PJQMB0138ZOperating Instructions (For Facsimile and Internet Fax/Email, For UF-9000)

2012 AU

PJQMC0029ZOperating Instructions (For Copy Arabic, For DP-180)

2021 ES

PJQMC0034ZOperating Instructions (For Copy Chinese, For DP-180)

2021 YV

PJQMC0052ZOperating Instructions (For Fax Chinese, For DP-180)

2022 YV

PJQQC0004Z Quick Guide (For DP-180) 2018 YA

PJQQC0005Z Quick Guide (For DP-180)2018

AG, AL, AM, AV, EB, EE, EH, EP

PJQQC0006Z Quick Guide (For DP-180) 2018 ER

PJQQC0007Z Quick Guide (For DP-180) 2018 YC

PJQTB0262Z Directory Holder (For UF-9000) 2015 AU

PJQTB0263Z Sheet, HVPS Insulation 1020 All

PJQTB0264Z Sheet, Right Cover 622 All

PJQTB0265U Label, F (For DP-180) 448 YV

PJQTB0265V Label, F (For DP-180) 448 EE

PJQTB0265W Label, F (For DP-180) 448 AV


184JUN 2004Ver. 2.0

UF-9000
DP-180/190
PJQTB0265X Label, F (For DP-180) 448 AG

PJQTB0265Y Label, F (For DP-180/190) 448Except AG, AV, EE, YV

PJQTB0265Z Label, F (For UF-9000) 448 AU

PJQTB0292Z Label, Color 446 All

PJQTC0003Z Label, Flash Memory 633 All

PJQTC0027Z Directory Holder (For DP-180/190) 2015 All

PJRAC0001Z Sheet, FM 712 All

PJUAB0005Y Plate, ADU Registration Roller 1408 OAPD All

PJUAB0007Z Chassis, Right 1724 OAPD All

PJUAB0008Z Chassis, Left 1725 OAPD All

PJUAB0024Y Plate, Lower Base 1401 OAPD All

PJULC0022Z Bracket, R 1737 All

PJULC0023Z Bracket, L 1736 All

PJUSB0008Z Plate, Transfer Bias Roller 1510 OAPD All

PJUSB0011Y Plate, Ground 1509 OAPD All

PJUSB0025Z Spring, Ground 816 OAPD All

PJUSB0027Z Plate, Pinch Roller 1704 OAPD All

PJUSB0080Z Spring, Ground 1711 OAPD All

PJUSB0089Z Spring, Side Guide 1808 OAPD All

PJUSB0130Z Plate, Spring 705 All

PJWACC00001 Software CD (For UF-9000) 2013 AU

PJWACC00002Operating Instructions CD (For DP-180/190)

2019 All

PJWACC00003 Software CD (For DP-190) 2013 AU

PJWACC00005 Software CD (For DP-180) 2013 Except AU, YV

PJWACC00007 Software CD (For DP-180) 2013 YV

PJWC1P7105M Assembly, Engine Board Shield Base 709 OAPD All

PJWEP7305M LSU 1114 OAPD All

PJWLPMF3M Cable, I/F 1949 OAPD All

PJWMP7100M Assembly, Registration Solenoid 822 OAPD All

PJWMP7305M Assembly, Pickup Solenoid 1320 OAPD All

PJWMPMF3M Clutch 1734 OAPD All

PJWP2P7100M1 PC Board, Paper Exit/ADU Paper Jam Sensor 1937 OAPD All

PJWP2P7105M1 PC Board, No Paper Sensor 1947 OAPD All

PJWP2P7305MPC Board, Registration/Paper Detect Sensor

1938 OAPD All

PJWP3P7100M1 PC Board, Low Toner Sensor 1944 OAPD All

PJWP3P7105M1 PC Board, 2nd Paper Feed Module I/F 1936 OAPD All

PJWPF2300EB Assembly, LVPS (DP-180) 1021 Except AU

PJWPPMF3M2 PC Board, 2nd Feeder 1945 OAPD All

PJWPUF9KEM PC Board, Engine Control 1902 All

PJWPWU00001Z Assembly, LVPS (For UF-9000/DP-190) 1021 AU

PJWQPMF3M Motor 1735 OAPD All

PJWS2P7100M Switch, OPC Drum Unit Interlock 1113 OAPD All

PJWSP7105M Switch, Front Door Safety Interlock 1112 OAPD All

PJYFPMF3M Assembly, Top Cover 1730 OAPD All

PJYK4P7305M Assembly, Pinch Roller Holder 607 OAPD All

PJYKF2300AU Door, Rear 612 All

PJZBP7305M Assembly, Upper Exit Roller Holder 1101 OAPD All

PJZC1P7100M Assembly, Upper Exit Roller Holder Cover 1109 OAPD All

PJZC1P7305M Assembly, Dust Scraper Cover 1315 OAPD All

PJZC2P7100M Bracket, Gear Support 821 OAPD All


185JUN 2004Ver. 2.0

UF-9000
DP-180/190
PJZC3P7100M Assembly, Side Fuser Cover 1226 OAPD All

PJZCP7305M Assembly, Paper Chute 1518 OAPD All

PJZE1P7100M Assembly, Pickup Lever 1319 OAPD All

PJZE1PMF3M Assembly, Paper Size Knob 1813 OAPD All

PJZEP7100M1 Pad, Separation 1615 OAPD PM All

PJZEP7305M Guide, Sub. Paper 1318 OAPD All

PJZEPMF3M1 Pad, Separation 1812 OAPD PM All

PJZFUS00001Z Assembly, Fuser Unit (For UF-9000) 1117 AU

PJZHP7100M Assembly, Drive Gear Bracket 908 OAPD All

PJZHP7105M Bracket, Fuser Drive Gear 823 OAPD All

PJZHP7305M Bracket, Motor 909 OAPD All

PJZR1P7305M Roller, Pickup 1316 OAPD PM All

PJZR2P7305M Assembly, Upper Exit Roller 1111 OAPD All

PJZR3P7100M Assembly, Lower Exit Roller 1227 OAPD All

PJZRP7305M Assembly, Cleaning Roller 1228 OAPD All

PJZRPMF3M Roller, Pickup 1733 OAPD PM All

PJZSF2300AU Assembly, Fuser Unit (For DP-190) 1117 AU

PJZSF2300EB Assembly, Fuser Unit (For DP-180) 1117 Except AU

PJZUP7100M Pan, Jam Release 1418 OAPD All

PJZUPMF3M Assembly, Paper Guide 1732 OAPD All

XPL2A10WVW Pin 1723 OAPD All

XSN2+10FN Screw W5 All

XSN3+4 Screw U9 All

XTB2+12J Screw W4 OAPD All

XTB3+4F Screw L9 All

XTB3+8G Screw F10 All

XTB3+8J Screw 19 All

XTB3+8JFN Screw V6 OAPD All

XTN3+8JFN Screw W8 All

XTS3+8J Screw W1 All

XTW26+8S Screw T8 OAPD All

XTW3+12S Screw U4 OAPD All

XTW3+12SFZ Screw U5 OAPD All

XTW3+6L Screw U1 All

XTW3+6LFC Screw V5 All

XTW3+6LFN Screw V9 All

XTW3+6S Screw V2 All

XTW3+8L Screw P3 All

XTW3+8LFN Screw H8 All

XTW3+8P Screw P8 All

XTW3+8PFN Screw V7 All

XTW3+8S Screw T9 OAPD All

XTW3+U8S Screw U8 OAPD All

XTW4+16P Screw V8 All

XUC4VW-V E-Ring U6 OAPD All

XWC3B Washer, Star G8 All

XWE4 Washer V3 All

XYC3+FF6 Screw V1 OAPD All

XYC3+FF8C Screw U3 OAPD All

XYN3+F5 Screw 3F All


186JUN 2004Ver. 2.0

UF-9000
DP-180/190
memo

187JUN 2004Ver. 2.0

E