Embed Size (px)
Citation preview
Please read the entire instruction manual before beginning
YOU MAY NEED
1
Hex Wrench
Thin SinkMountingSupport
4
Turn off water supply valves and relieve pressure!Pry off plug button using a small flathead screwdriver.Unscrew set screw using Hex Wrench.Remove handle.
Remove handle.Unscrew dome cap counter clockwise by hand.Unscrew retaining nut using adjustable wrench.Remove cartridge assembly and inspect seals.Contact Giagni for any parts needed or re-assemble partsby reversing steps.
Handle Removal Maintenance Valve Cartridge Removal Maintenance
PACKING LIST
Sprayer
FaucetBody
Giagni warrants to the initial consumer purchaser of this product to be free from defects in material and workmanship during normal residential use for a lifetime. This warranty do not cover normal wear and tear or damage to the surface caused by the use of chemicals or chlorides. Damage caused by accident, misuse, abuse, or practices not in compliance with the care guide included with the product is not covered by this warranty.
If any defects develop under warranty from the date of purchase, Giagni will replace the product or defective components. Improper use or installation will immediately void this warranty. No other liability or obligation is to be assumed. Proof of purchase (original sales receipt) from an authorized Giagni reseller must be provided to Giagni for all warranty claims. Giagni will not be responsible for shipping charges, labor charges, installation or any other consequential costs. In no event shall the responsibility of Giagni exceed the purchase price of the product.
Care
Warranty
GF-183A Series Kitchen Faucet
Rubber WasherMetal WasherMounting Nut
O-Ring
Giagni, IncMount Vernon, [email protected]
1. Clean the faucet regularly with clear water or mild liquid soap, rinse the faucet with clear water then dry with a soft cotton cloth.2. Do not use any abrasive cleansers, polishes, cloths, scouring pads or paper towels.3. Do not use any acidic detergents.
3
Flush the lines of air and debris by moving the handle tothe open position and running the water in both the hotand cold positions for about a minute. This keeps that debrisfrom clogging the sprayer.
Be sure the hot and cold settings are properly operating.If they are switched, switch the supply line connections tothe supply valves.
Replace the sprayer and rubber washer. See that the sprayer is operating in both modes. The sprayer should reset to aerator mode after the faucet is shut off.
Check for leaks, both in the on and off positions.
8
INSTALLATION PROCEDURESTurn off the water supply valves
If you are replacing an existing faucet, remove the faucetfrom the sink and clean the sink surface thoroughly.
Make sure the O-Ring is placed onto the bottom ofBase Ring before installing.
Install faucet through the desired hole in the sink and/orcountertop.
Position faucet as desired and tighten the Mounting Nut.
Connect hot and cold water supply lines to your watersupply valves. The supply lines are marked accordingly.
2
1
2
4
6
Close
Open
HotCold
Remove the Sprayer from the hose. Be sure to find and putaside the rubber washer that seals it to the hose.
Keep the hose docked in the arm
Rotate the handle to the closed position.
NOTE: For mounting directly onto thin sinks, a Thin SinkMounting Support is supplied to help stabilize the faucet.If used, it is the first item to go onto the faucet from below.Do not use for thicker sinks or when mounting faucet to acountertop.
From underside of sink, attach the mounting hardwareto the faucet body in this order:1. Thin Sink Mounting Support (optional)2. Rubber Washer3. Metal Washer4. Mounting Nut
3
O-Ring
Thin SinkMounting Support(Flat side up)Optional
Turn on the water supply valves.7
ClosedOpen
5
