poolLUX PowerpLX-PW60 & pLX-PW100

Installation InstructionsRead all instructions before attempting to perform installation work

Type 3R Rainproof Enclosure

FOR USE WITH POOL AND SPA PRODUCTS

5005508

ETL LISTEDConforms to UL STD 379;

Certifi .ed .to .CSA .STD .C22 .2 .#218 .1

79-15265-00 .Rev .B

2

ContentsIMPORTANT SAFETY INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3

Electrical Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Recommended Tools and Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Enclosure Mounting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5

Input / Supply Line Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Output Wiring for Lights and Light Sources . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

OPERATING INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Manual Rocker Switch Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

WIRING DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

REPLACEMENT PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

3

I M P O R T A N T S A F E T Y I N F O R M A T I O N

CAUTION: POWER AND SIGNAL OUTPUT CONDUITS MUST BE NON-METALLIC

ATTENTION: CONDUITS POUR PUISSANCE DE SORTIE ET SORTIE SIGNAL DOIT ETRE NON METALLIQUE

ELECTRICAL SHOCK HAZARD – SWITCH DOES NOT TURN OFF INPUT POWER.Failure .to .disconnect .input .power .before .servicing .can .lead .to .serious .injury, .or .death .

Disconnect .input .power .before .servicing .

Replace all parts and panels before reconnecting power and operating

DANGER – FAILURE TO FOLLOW THESE WARNINGS, INSTRUCTIONS, AND THE OWNER’S MANUAL MAY RESULT IN SERIOUS INJURY OR DEATH.

Basic .safety .precautions .shall .be .observed .when .installing .and .operating .the .poolLUX .Power . (p/n .pLX-PW60/PW100) .and .other .associated .equipment:

1 . . A .qualified .electrician .must .install .the .poolLUX .Power .(p/n .pLX-PW60/PW100) .in .accordance .with .the .requirements .of .NEC .ANSI/NFPA .70 .and .Article .680 .

2 . . The .poolLUX .Power .(p/n .pLX-PW60/PW100) .must .be .mounted .on .a .flat .vertical .surface . .The .unit .must .be .a .minimum .of .4 .inches .above .the .ground .level, .pool .deck, .or .higher .than .8 .inches .above .the .maximum .pool .water .level, .whichever .provides .greatest .elevation . . .The .unit .must .be .positioned .a .minimum .of .4 .feet .(1 .2 .m) .away .from .the .inside .wall .of .the .pool, .unless .separated .from .the .pool .by .a .solid .fence, .wall, .or .other .permanent .barrier .

3 . . CAUTION: .THE .EQUIPMENT .AND .CONTROLS .SHALL .BE .LOCATED .NOT .LESS .THAN . 1 .M .HORIZONTALLY .FROM .THE .SPA .OR .HOT .TUB .

4 . . ATTENTION: .MAINTENIR .UNE .DISTANCE .MINIMALE, .MESURÉE .DANS .UN .PLAN .HORIZONTAL, .DE .1 .M .ENTRE .LA .CUVE .DE .RELAXATION .ET .LES .APPAREILS .ET .COMMANDES .

5 . . ONLY .USE .COPPER .CONDUCTORS .

6 . . Do .not .exceed .the .maximum .electrical .ratings .of .the .poolLUX .Power .(p/n .pLX-PW60/PW100) .components .(indicated .on .page .4), .wiring .devices, .and .current .carrying .capacity .of .the .conductors .

7 . . poolLUX .Power .(p/n .pLX-PW60/PW100) .is .intended .to .be .used .with .low .voltage .underwater .luminaires .that .comply .with .Article .680 .of .the .National .Electrical .Code .and .does .not .require .bonding .due .to .their .polymeric .or .isolated .application .design .

8 . . This .device .should .never .operate .equipment .that .could .cause .property .damage, .bodily .injury, .or .death .should .it .be .activated .unexpectedly .

9 . . Use .with .branch .circuit .breakers .with .15 .amperes .or .less .

10 . . This .device .must .be .used .with .an .approved .ground-fault .circuit .interrupter .(GFCI) . .

11 . . Use .rain-tight .or .wet .location .hubs .that .comply .with .the .requirements .in .the .standard .(UL514b) .for .conduit, .tubing, .and .cable .fittings .only .

12 . . The conduit hub is to be connected to the power input conduit before the hub is connected to the .enclosure .

13 . . Never .allow .children .to .operate .the .pLX-Power .unit .unsupervised .

4

E l e c t r i c a l R a t i n g s

Do .not .exceed .the .maximum .electrical .output .rating .of .each .unit .listed .below . .

Model Input Output pLX-PW60 . 120 .VAC, .60 .Hz, .0 .6A .max . 12-13 .VAC, .60 .Watt .maxpLX-PW100 . 120 .VAC, .60 .Hz, .1 .0A .max . 12-13 .VAC, .100 .Watt .max

Use .a .15 .Amp, .120VAC .GFCI .Circuit .Breaker .for .input .power . .

Thermal CutoffsTo .help .protect .against .undesirable .thermal .conditions, .the .poolLUX .Power .(p/n .pLX-PW60/PW100) .utilizes .thermal .cutoffs .that .will .stop .electricity .in .the .event .of .an .overload, .or .overheat .condition . .When .the .fault .condition .is .rectified, .the .output .power .will .self-reset .without .user .intervention .

Output FuseTo .protect .against .hazardous .electrical .conditions, .the .poolLUX .Power .(p/n .pLX-PW60/PW100) .utilizes .a .current .fuse .that .will .cut .off .output .electricity .in .the .event .of .a .short .circuit .condition . . .When .the .fault .condition .is .rectified .and .the .fuse .is .replaced, .normal .operation .will .resume . . . Only .use .S .R .Smith .replacement .fuses: .

36-15017-00 .(pLX-PW60) . 36-15018-00 .(pLX-PW100)

R e c o m m e n d e d To o l s a n d S u p p l i e s

1 . . Circular hole saw for installation of 3/4" .and .or .1" non-metallic conduit depending on installation .requirements . .Do not use spade bits for opening the conduit knockouts.

2 . . Application .appropriate .and .approved .‘rain-tight’ .or .‘wet .location’ .conduit .hubs . .

3 . . Additional .duct .seal .may .be .required .for .three .or .more .conduit .installations . * Note: .Every .installation .will .have .at .least .two .conduits .- .one .for .input .power .and .one .for .output .power . .Most .installations .will .likely .have .several .output .power .conduits . .

4 . . Slotted .screwdriver, .size .#2

5 . . Phillips .screwdriver, .size .#2 .

6 . . Drill

7 . . #10 .Screws .appropriate .for .installing .the .product .onto .a .wall .(installer supplied) * Note: It is recommend to hand tighten all screw terminals and screw fasteners inside the enclosure .and .front .cover .until .snug .and .secure . .Be .sure .not .to .overtighten .as .permanent .damage .may .occur .

5

I N S T A L L A T I O N I N S T R U C T I O N S

WARNING• TURN .OFF .INCOMING .POWER .BEFORE .SERVICING .EQUIPMENT .

• ALL .INSTALLATION .AND .MAINTENANCE .WORK .MUST .BE .PERFORMED .BY .A . QUALIFIED .ELECTRICIAN .

• GFCI .BREAKER .MUST .BE .USED .TO .CONNECT .(p/n .pLX-PW60/PW100) .TO .INPUT .POWER .

• VERIFY .ALL .ELECTRICAL .RATINGS .BEFORE .INSTALLATION .IS .COMPLETE .

• FOLLOW PROPER WIRING PRACTICES IN ACCORDANCE WITH ALL NATIONAL AND LOCAL .REGULATORY .REQUIREMENTS .

E n c l o s u r e m o u n t i n g

1 . . Locate .the .poolLUX .Power .(p/n .pLX-PW60/PW100) .in .an .appropriate .area .that .meets .the .following .requirements:

a . .Must .be .mounted .on .a .flat .vertical .surface . . .

b . .Must .be .a .minimum .of .4 .inches .above .the .ground .level, .pool .deck, .or .higher .than .8 .inches .above .the .maximum .pool .water .level, .whichever .provides .greatest .elevation .

c . .Must .be .positioned .a .minimum .of .4 .feet .(1 .2 .m) .from .the .inside .wall .of .the .pool .unless .separated .from .the .pool .by .a .solid .fence, .wall, .or .other .permanent .barrier . .

For .the .unit .to .be .adequately .air .cooled, .allow .a .minimum .gap .of .9/32" .(7 .2mm) .between .the .wall .and .the .back .surface .of .the .unit . .The .stand-off .mounting .tabs .will .make .contact .with .the .wall .

WA

LL

Minimum .Gap .of .9/32" .or .7 .2mm

6

2 . . By .hand, .open .the .enclosure .by .pulling .the .front .cover .off .evenly .by .the .top .and .bottom .tabs . .Do .not .angle .or .‘hinge’ .the .cover .when .removing .or .damage .may .occur . .If .you .cannot .open .the .enclosure .by .hand, .use .a .flat .blade .screwdriver .to .twist .open .the .finger .tabs .of .the .cover .at .the .top .and .bottom .of .the .unit .

3 . . Securely .install .a .wall .material .appropriate .#10 .screw .(Installer .Supplied) .into .the .location .where .the .unit .will .be .installed . .The .screw .head .must .be .1 .1/8” .away .from .the .wall .to .allow .the .unit .to .be .mounted .correctly .

4 . . Place .the .mounting .tab .of .the .poolLUX .Power .(p/n .pLX-PW60/PW100) .over .the .#10 .screw .and .let .it .hang .in .place . .Level .the .unit .and .mark .the .remaining .2 .mounting .screw .locations .on .the .wall . .Use .2 .more .material .appropriate .#10 .screws .(Installer .Supplied) .to .secure .the .unit .to .the .wall .through .the .mounting .holes .on .the .back .of .the .unit . .Once .the .lower .two .screws .are .secure, .tighten .the .top .screw .to .securely .hold .the .upper .portion .of .the .enclosure .in .place .

Top View

Enclosure

Front View

Enclosure

Side View EnclosureRemove .front .cover .by .evenly .pulling .the .top .

and bottom tabsBottom View

Enclosure

Top Tab

. Bottom .Tab

7

I n p u t / S u p p l y L i n e V o l t a g e

1 . . Remove .the .metal .input .voltage .isolation .barrier .by .unscrewing .the .mounting .screw . .Once .the .securing .screw .is .removed, .the .isolation .cover .will .pull .straight .out .to .allow .easier .access .to .the .conduit .knockout .locations .

TRANSFORMER

TRANSFORMER

Metal Input Voltage Isolation Barrier .Mounting .Screw .

Locations of Input Power Knockouts

Locations of Output Power Knockouts

*Note: .Once .all .conduits .are .connected, .replace .the .metal .input .voltage .isolation .barrier .and .mounting .screw . .Tighten .until .the .mounting .screw .is .secure . . .

2 . . Bring .the .supply .power .conduit .to .one .of .the .four, .lower .right .input .power .conduit .knockout .locations .that .terminate .‘inside’ .the .isolation .barrier . .No .output .connections .are .allowed .through .these .knockout .locations . *Note: .The .wiring .of .the .input .and .output .power .are .required .to .use .separate .conduits .and .must .not .share .an .individual .conduit . .No .conduit .should .contain .both .input .and .output .power .wiring .

3 . . Using .a .hole .saw, .open .the .knockouts .for .the .size .of .the .conduit .(¾" .or .1") .being .installed .

ON

OFF

8

4 . . Attach .an .approved .‘rain-tight’ .or .‘wet .location’ .hub .to .the .conduit . .After .the .hub .is .attached . to .the .conduit, .attach .the .hub .to .the .enclosure .

5 . . Connect .the .GFCI .protected, .15A .max, .supply .voltage .line .to .the .right .side .of .the .terminal .block . .Strip .¼” .of .insulation .and .then .connect .the .wires .to .the .marked .terminals .and .tighten .securely . 120V .Hot .GFCI .Load .to .terminal .marked: . . H 120V .Neutral .GFCI .Load .to .terminal .marked: . N Electrical System Ground to terminal marked: GND

6 . . Replace .and .secure .the .metal .input .voltage .isolation .barrier .and .verify .that .the .input .wiring .screw .terminals .are .secure .

12

VA

C

13

VA

C

PO

WE

R IN

PU

TN

EU

TR

AL

PO

WE

R IN

PU

T

PO

WE

R IN

PU

TG

RO

UN

D

CO

M

GR

OU

ND

GND N H

Input Wiring Locations

O u t p u t W i r i n g f o r L i g h t s a n d L i g h t S o u r c e s

1 . . The .combined .load .of .all .lights .connected .to .the .poolLUX .Power .must .not .exceed .the .following: • . pLX-PW60 .= .60 .watts .max • . pLX-PW100 .= .100 .watts .max

2 . . The .enclosure .provides .four .(4) .output .conduit .locations . .If .additional .conduit .terminations .are .required, .an .approved .junction .box .may .be .used .as .a .termination .point .and .multiple .output .cables .may .be .run .through .a .single .feeder .conduit .to .the .poolLUX .Power .

TRANSFORMER

Locations of Input Power Knockouts

Locations of Output Power Knockouts

GND12V L/V 13V

Fuse Holder

9

12

VA

C

13

VA

C

PO

WE

R IN

PU

TN

EU

TR

AL

PO

WE

R IN

PU

T

PO

WE

R IN

PU

TG

RO

UN

D

CO

M

GR

OU

ND

GNDGND12V NL/V H13V

Output Wiring Locations

3 . . Using .a .hole .saw, .open .the .knockout .for .the .size .of .the .conduit .(¾" .or .1") .being .installed . .

4 . . Bring .output .conduits .to .the .open .conduit .locations . .Any .conduit .used .as .output .wiring .runs .between .the .lights .and .pLX-Power .unit .(p/n .pLX-PW60/PW100) .and .any .external .controller .shall .be .Non-Metallic .(Polymeric) . . ATTENTION: LES CONDUITS DOIVENT ÊTRE RELIÉS PAR LA MASSE

5 . . Attach .an .approved .‘rain-tight’ .or .‘wet .location’ .hub .to .the .conduit .first, .and .then .attach .hub .to .the .enclosure . .

6 . . The .poolLUX .Power .has .has .two .low .voltage .electrical .output .terminals .(Taps) .or .connection .points .that .allow .for .12VAC .or .13VAC .operation . .Securely .connect .the .lights’ .two .conductors .to .the .electrical .(taps) .output .terminals . .Most .installations .will .utilize .the .terminal .configuration .of .12VAC .terminal .and .low .voltage .common .terminal . .In .some .cases .additional .voltage .may .be .required .to .operate .the .lights .requiring .use .of .the .13VAC .terminal .and .the .low .voltage .common .terminal .

*Note: .DO .NOT .use .or .bridge .both .the .12VAC .and .13VAC .terminal .positions .at .the .same .time . .

7 . . Do .a .final .inspection .to .verify .all .wiring .connections .are .correct .

8 . . Once .inspected, .align .the .panel .bayonet .guides .to .the .snap-in .receivers .along .the .centerline .of .the .enclosure . .Evenly .and .gently, .push .the .cover .in .place .ensuring .that .both .the .top .and .bottom .latches .‘snap’ .in .place .

9 . . Apply .power .from .the .input .supply .voltage .to .the .unit .and .function .test .the .unit .via .the .two-way .rocker .switch .on .the .upper, .right .side .of .the .unit .

CAUTION – IF USING FEEDER OR SUPPLY LINES TO A JUNCTION BOX, BE SURE TO USE THE APPROPRIATE WIRE GAUGE FOR THE LOAD AND DISTANCES INVOLVED.

or

10

O P E R A T I N G I N S T R U C T I O N S

M a n u a l R o c k e r S w i t c h O p e r a t i o n

The .poolLUX .Power .comes .with .one .rocker .switch . for .operation . .The .switch .must .be .in .the .OFF .(Down) . position .before .powering .on .for .the .first .time . . To .turn .ON .(Up) .the .12VAC .connected .lights, . flip .the .Rocker .Switch .UP .or .to .the .ON .position . . To .turn .OFF .the .12VAC .connected .lights, .flip .the . Rocker .Switch .to .the .DOWN .or .OFF .position . . .

Color Changing OperationTo change LED pool light colors simply toggle between .the .ON/OFF .position .within .1 .second . of each toggle until the desired color or light show .is .reached . .

WARNING

ELECTRICAL SHOCK HAZARD –SWITCH DOES NOT TURN OFF INPUT POWER.Failure to disconnect input power before servicing can lead to serious injury, or death.Disconnect input power before servicing.Replace all parts and panels before reconnecting power and operating.

11

W I R I N G D I A G R A M

Electrical Connections

NOTES: UNLESS

OTHERWISE SPECIFIED

1 . . WIRE .COLOR .LEGEND:

. R .= .RED

. W .= .WHITE

. BK .= .BLACK

. B .= .BLUE

. Y .= .YELLOW

. G .= .GROUND

2 . . . ELECTRICAL . . .

CONNECTIONS LEGEND:

. 12V .= .12VAC

. . L/V .= . .LOW .VOLTAGE .

COMMON

. 13V .= .13VAC

. GND .= .GROUND

. N .= . .POWER .INPUT .

NEUTRAL

. H .= .POWER .INPUT

TRANSFORMER

12

VA

C

13

VA

C

PO

WE

R IN

PU

TN

EU

TR

AL

PO

WE

R IN

PU

T

PO

WE

R IN

PU

TG

RO

UN

D

CO

M

GR

OU

ND

GND N HGND12V L/V 13V

B R Y G

G

W BK

BK ON

OFF

12

R E P L A C E M E N T P A R T S

Replacement parts for the poolLUX Power (pLX-PW60 or pLX-PW100): Transformer .(pLX-PW60) . . . . . 44-15039-00 . .

Transformer .(pLX-PW100) . . . . 44-15040-00 .

2-Way .Switch . . . . . . 38-15002-00 . .

Isolation .Barrier . . . . . . 02-15342-00 . .

Isolation .Barrier .mounting .screw, .8-32 . . 10-15078-05 . .

Fuse .Holder . . . . . . 36-15016-00

Fuse .(pLX-PW60) . . . . . . 36-15017-00

Fuse .(pLX-PW100) . . . . . 36-15018-00

S .R .Smith, .LLC

P .O . .Box .400 . .| . .Canby, .OR .97013

P .503 .266 .2231 . . .TF .800 .824 .4387

srsmith.com

© .2017 .S .R .Smith . .All .rights .reserved . . .79-15265-00 .Rev .B

Questions? Contact .One .of .Our .Dedicated .Lighting .Specialists . . 1-800-824-4387 x4012 . .or . .x2282

kēlo LED Light

Installation InstructionsRead all instructions before attempting to perform installation work

Installation information applies to both RGB and White Light only models

This product is protected by one or more of the following U.S. Patents: 6781329, 6936978 and 6967448

4005496

ETL LISTEDConforms to UL STD 676;

Certified to CSA STD C22.2 #89

79-15271-00

2

3

ContentsOVERALL DIMENSIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

IMPORTANT INSTALLATION INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . 4

INSTALLATION INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

TYPICAL INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

WINTERIZATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

BASIC OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

ADVANCED OPERATION VIA ACP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

4

I M P O R T A N T I N S T A L L A T I O N I N F O R M A T I O N

O V E R A L L D I M E N S I O N S

1. Ensure that the electrical system for your pool conforms with all requirements of the National Electrical Code (NEC) and all relevant local codes and ordinances.

2. This 12VAC Underwater Light must be installed in accordance with the National Electrical Code by a Certified Electrician or a Qualified Pool Technician. NOTE: No Bonding Terminal is required on the forming shell since the fixture is an all plastic construction and complies with NEC article 680 Requirements.

3. Waterproof conduit must be used from the S.R.Smith kēlo LED Light to the ‘above ground’ power supply equipment.

4. For supply connection, use only an isolating low voltage power supply with ungrounded output, evaluated for swimming pool use.

5. DO NOT CONNECT THIS 12VAC LIGHT DIRECTLY TO A 120VAC CIRCUIT - LIGHT WILL BE DAMAGED.

6. Fit your S.R.Smith kēlo LED Light/s as outlined in the following detailed installation instructions.

7. Except when the luminaire is installed in an area of the swimming pool that is not used for swimming and the lens is adequately guarded to keep any person from contacting it, the luminaire shall be installed in or on a wall of the pool, with the top of the lens opening not less than 100 mm (4 inches) below the normal water level of the pool.

CONNECT ONLY TO POWER SUPPLY INTENDED FOR USE WITH SUBMERSIBLE LUMINAIRES

THIS DEVICE IS NOT INTENDED FOR USE WITH EMERGENCY EXITS

74.18mm / 2.92”

59.7mm / 2.35”

17mm0.669”

88

.2m

m / 3

.47

”

ELECTRICAL SPECIFICATIONInput Voltage: 12VAC

Color Change (RGB): 7 Watts max.

White Light Only: 5 Watts max.

COLOR CONTROLBasic 12VAC mode (off/on control toggling)

S.R.Smith poolLUXTM ACP* compatible – see pg 7for additional information

5

I N S T A L L A T I O N I N S T R U C T I O N S

T Y P I C A L I N S T A L L A T I O N

1. Per NEC Article 680.23 (5) lights are to be installed in no less than 18” (450mm) below the normal water level unless the luminaire is listed and identified for use at lesser depths. S.R.Smith lights are listed and identified for use at depths no less than 4” (100mm) below the normal water level. Max depth is 36” below water surface. All depth measurements are from the normal water level to the top of the Luminaire lens.

2. Fit an S.R.Smith LNS-2G, LNS-2A, LNS-2V or similar 1 1/2” pool wall fitting into the pool wall at the selected location. Watertight PVC conduit must be used from the wall fitting to the above water/ground level conduit termination on the equipment or supply side of the 12V AC line. Please refer to the illustration below.

3. Fit the S.R.Smith kēlo LED Light into the 1 1/2” wall fitting as shown and carefully pull the waterproof supply cable through. Carefully thread the S.R.Smith kēlo into the threads and turn clockwise and gently tighten until secure. DO NOT Over-tighten the light as damage may occur. Connect the red / black wire conductors of the S.R.Smith kēlo to an approved, low voltage, class 2, Magnetic Type Power Source that complies with UL379 or an S.R.Smith poolLUX™ brand power supply as required by NEC or relevant local codes and ordinances.

NOTE: Even though the housing gasket (between Wall Fitting and Light) can be replaced by a bead of silicon suitable for pool use, water will eventually fill the conduit so be sure the conduit is watertight and terminates above ground.

FOR STANDARD 1 1/2” WALL FITTINGS IN A POOLS OR SPA

Luminaire is listed and identified for use at 4” or more below the normal water level of the pool.

Optimal lighting coverage may be found at 10-12” below water level.

Maximum depth is 36”

*Approved 12VAC Class 2 Power

Source (see line #3 above)

1.5” watertight, underground PVC conduit back to 12VAC transformer.

All fittings should be glued and watertight.

*Minimum of 3.5” of straight, 1.5” PVC conduit behind the wall fitting required prior to conduit reducer or bend.

back gasket

pool deck

4”Min

18” NEC Article 680.23(5)

6

W I N T E R I Z A T I O N R E C O M M E N D A T I O N S

B A S I C O P E R A T I O N

Swimming Pools may or may not be drained completely. If not drained completely, the water level should be lowered below the S.R.Smith kēlo LED Light and make sure that all water is drained from the wall fitting and conduit. Alternatively, the S.R.Smith kēlo LED Light may be removed completely, the conduit purged of all water, and a 1 1/2” NPT male plug with thread sealing tape may be used to close the wall fitting.

NOTE - If water is trapped in conduit, damage may occur from freeze expansion.

When connected to an approved, 12VAC, Class 2 power supply - The S.R.Smith kēlo LED color changing light uses simple ‘off / on’ power switching to control the basic, pre-defined color modes with memory function.

MEMORYThe memory function remembers the last color setting. For example, if the light was last used in the blue mode, the next time the light is turned on it will be blue mode.

COLOR MODE SELECTIONThe LED will turn on to the color in memory. To move to the next color mode, quickly (within one second or faster) toggle the power to the lights

’OFF / ON’.

Advance through the modes until the desired mode is selected. The modes will cycle 1,2,3,4,5,6,7,8, then cycle back to 1. See table below for details.

COLOR SYNC RESET

To synchronize all lights on the system including older *Fiberstars LED Series Pool lights, you must use the following sequence:

1. Turn lights ‘ON’ to confirm the color modes are out of sync.

2. Turn lights ’OFF’ for 5 seconds or more.

3. Toggles lights ’ON’ / OFF’ three times within three seconds - must end in ’OFF’ condition

4. Leave lights in ’OFF’ condition for 5 seconds.

5. Turn lights ‘ON’ and confirm that all lights are in mode #1, Soft Color Change

* Older Fiberstars LED lights can synchronize with the newest generation lights ONLY if they have their DIP switches in their default, ’All Down’ position. In a mixed environment, the Color Sync Reset will need to be performed each time the lights are used and color synchronization is desired.

FOR LED COLOR CHANGING LAMP (RGB)WHITE ONLY LAMPS ARE SIMPLY ON OR OFF

COLOR MODE SELECTION GUIDE

Mode 1 Soft Color Change

Mode 2 White

Mode 3 Blue

Mode 4 Green

Mode 5 Red

Mode 6 Amber

Mode 7 Magenta

Mode 8 Flash Color Change

7

A D V A N C E D O P E R A T I O N V I A A C P

Advance Control Protocol (ACP) provides dimming and custom color control through a dedicated color remote control. All S.R. Smith LED lights (kēlo ®, Fiberglass®, Treo Micro®) and 2015 or later water features are ACP compatible.

This light is equipped with a thermal protection circuit built into the LED lamp assembly. If the circuit detects that the

lamp assembly is getting too hot for a given environment, it will automatically reduce the brightness in increments until

the lamp remains below the thermal threshold. If this condition occurs, it may or may not be noticeable by the human

eye and is a normal function, not a sign of malfunction or failure.

S.R.Smith, LLC

P.O. Box 400 | Canby, OR 97013

P 503.266.2231 TF 800.824.4387

srsmith.com

© 2018 S.R.Smith. All rights reserved. 79-15271-00 0318

Questions? Contact One of Our Dedicated Lighting Specialists. 1-800-824-4387 x4012 or x2282