Pre-Delivery Guide - Clearwater Spas Guide. Congratulations on your decision to purchase a spa. Clearwater Spas manufacturers the best built and most energy efficient spas in the industry

Pre-Delivery Guide

Congratulations on your decision to purchase a spa. Clearwater Spas manufacturers the best built and most energy efficient spas in the industry. You have now entered an elite group of spa owners.

pre-delivery guide 4-1-14

www.clearwaterspas.com

Energy E�cient Recycling Program Manufacturing Clean Water Clean AirCerti�ed

CEC

Pre-Delivery Guide2

IMPORTANT INFORMATION

Please take a moment to read through the information provided on these pages. We want you to receive your purchase in excellent condition so you can begin enjoying it. The information also includes important specifications about how to prepare the site for the delivery. This book specifically covers site preparation, delivery access, and electrical requirements.

Remember to read the Owner’s Manual, located in the equipment area of the spa. Some of the instructions here are also located in the Owner’s Manual. On the data plate is the spa model and serial number, which is important for warranty claims.

Clearwater Spas reserves the right to change or modify the spas or any of the features without notification or any obligation.

Please make a record of the following information.It will be valuable if service is required.

Date Purchased: ____________________________

Date Installed: ____________________________

Dealer: ____________________________

Address: ____________________________

Phone: ____________________________

In most cities, permits are required for the installation of electrical circuits or the con-struction of a deck or gazebo. In addition, some communities have ordinances concern-ing hot tubs, usually directed toward their safety when no one is home. Your Clearwater Spa is equipped with safety locks to prevent unsupervised child access. For any further questions or clarifications, your local building department is a good source. Your Clear-water Spas dealer will be able to answer all of your questions.

Clearwater Spas18800 Woodinville/Snohomish Rd.

Woodinville, WA 98072

Phone: 425.483.1877Fax: 425.487.1148


Pre-Delivery Guide 3

DELIVERY ACCESS

MEASURE BEFORE YOU PURCHASEOn the chart below, find your spa and relevant dimensions. These dimensions are of the spa laying on its side.

Next, contact your spa dealer for the dimensions of the cart used to deliver your spa. Use the height of the cart and the “H” mea-surement for the vertical dimension. Use the width of the cart or “W”, whichever is greater, to determine the maximum clearances of the width.

Note: If there are stairs or other obstacles, the spa will have to travel over to get to the site, additional clearances may be required. Use the supplied measurements to help you determine the best location for your new spa. If you have any problems, contact your dealer for assistance.

U.S./Canada Specifications:Model Width & Length-in Depth Filter

AreaHeater (Watts)

Water Capacity

Dry Weight

Seats Filled Weight*

Dead Weight*

Electrical Reqmts.

in. cm. in. cm.

Resort Series

Orlando 92.5”x92.5” 235 x 235 cm 38" 95.6 cm 150 sq ft 4000w 540 gal 1100 lbs 6 5420 lbs 6470 lbs 240 v

Monaco 92.5”x92.5” 235 x 235 cm 38" 95.6 cm 150 sq ft 4000w 440 gal 1100 lbs 5 4620 lbs 5495 lbs 240 v

Cabo 84”x84” 213.4 x 213.4 cm 38" 95.6 cm 150 sq ft 4000w 330 gal 800 lbs 5 3340 lbs 4215 lbs 240 v

Rio 84”x75” 213.4 x 190.5 cm 34" 86 cm 150 sq ft 4000w 300 gal 700 lbs 4 3100 lbs 3800 lbs 240 v

Beachcraft Series

Pearl Island 92.5”x92.5” 235 x 235 cm 38" 95.6 cm 150 sq ft 4000w 430 gal 750 lbs 5+ 4190 lbs 5240 lbs 240 v

Tradition 92.5”x92.5” 235 x 235 cm 38" 95.6 cm 150 sq ft 4000w 460 gal 750 lbs 6-7 4430 lbs 5830 lbs 240 v

St. Andrew 84”x84” 213.4 x 213.4 cm 34" 86 cm 150 sq ft 4000w 340 gal 600 lbs 5+ 3516 lbs 4216 lbs 240 v

Myrtle Beach 84”x84” 213.4 x 213.4 cm 34" 86 cm 150 sq ft 4000w 350 gal 600 lbs 6-7 3682 lbs 4557 lbs 240 v

XS Series

XS93L 92.5”x92.5” 235 x 235 cm 38" 95.6 cm 50 sq ft 4000w 430 gal 600 lbs 6-7 4182 lbs 5582 lbs 240 v

XS93NL 92.5”x92.5” 235 x 235 cm 38" 95.6 cm 50 sq ft 4000w 450 gal 750 lbs 7-8 4182 lbs 5582 lbs 240 v

XS84L 84”x84” 213.4 x 213.4 cm 34" 86 cm 50 sq ft 4000w 320 gal 500 lbs 6 3367 lbs 4382 lbs 240 v

XS84NL 84”x84” 213.4 x 213.4 cm 34" 86 cm 50 sq ft 4000w 340 gal 500 lbs 6-7 3367 lbs 4382 lbs 240 v

XS76L 76”x76” 193 x 193 cm 34" 86 cm 50 sq ft 4000w 260 gal 420 lbs 5 2500 lbs 3375 lbs 240 v

XS76NL 76”x76” 193 x 193 cm 34" 86 cm 50 sq ft 4000w 300 gal 420 lbs 6-7 2500 lbs 3375 lbs 240 v

XS76CC 76”x76”x36" 193x193x91 cm 34" 86 cm 50 sq ft 4000w 220 gal 410 lbs 4-5 2360 lbs 3235 lbs 240 v

XS76R 76"x53" 193 x 135 cm 34" 86 cm 50 sq ft 4000w 180 gal 360 lbs 3 1889 lbs 2414 lbs 240 v

XS76T 76"x76"x92" 193x193x234 cm 33" 84 cm 50 sq ft 4000w 180 gal 360 lbs 3 1861 lbs 2386 lbs 240/120 v

CAUTION: Clearwater Spas suggests an engineer or contractor be consulted before the spa is placed on an elevated deck. *NOTE: The “Filled Weight” and “Dead Weight” of the spa includes the weight of the occupants (assuming an average occupant weight of 175 lbs).

Pre-Delivery Guide4

STEPS FOR A SUCCESSFUL INSTALLATION:

1. PREPARING FOR YOUR SPA

Prior to receiving your new spa, you will need to prepare an area to install the spa. You will need to arrange to have your spa placed in your desired location and the connection of the electrical circuits. In most cities, permits are required for the installation of electrical circuits.

Review the path that your spa will take through your property along with the size of the spa to ensure you have enough clear-ance. If there are stairs or other obstacles, the spa will have to travel over to get to the site, additional clearances may be required.

We have listed some key points to installing your spa that will help eliminate some of the unforeseeable situations that could occur.

• Avoidinstallingtooclosetoabuildingorstructure. • Leaveenoughroomaroundallsidestoallowaccessto service panels. • Installonaloadbearing,levelplatform. • Donotinstalllessthan5feetfromgroundconductors. • Usenon-conductiveconduitforallwiring. • Ifinstallingbelowadecksurface,leaveenoughroom to access and remove service panels.

We recommend a level 4” thick concrete pad if you are installing on land (versus deck or platform). The dimensions of the pad should be at least the outside dimension of the spa. You should also accommodate for steps or other items around the spa. Allow a few days for curing the cement when calculating your scheduled delivery date.

Balconies and upper decks are not recommended for spa installations, but if you choose to do so, keep in mind that a large filled spa with 6 people can weigh as much as three tons. Balconies and decks must be constructed to current state and local building codes and must support at least 100 pounds per square foot.

If you are building a deck around the spa, be sure that the deck does not cover any of the service panels to the spa. If you are building stairs for getting up to the spa, it is recom-mended that they be installed in such a way that they can be moved out of the way if entrance to the service panels is required.

The most obvious thing to remember is to plan your installation in a location where it will be easy to move from the delivery truck to the location site. Spas are typically trans-ported on a mover’s dolly lying on their side. Check for adequate gate clearance and remove any fence panels if necessary to allow access to the installation site.


2. SITE SELECTION AND PREPARATION

The location of your hot tub is entirely up to you. Care-fully read these instructions for various ideas of loca-tions that your new hot tub may be placed.

By the time you have made your spa purchase, you probably have a spot already picked out. Prior to the spa delivery, please verify the following:

• Alwaysplacethespaonacompactedandlevelsurface.Thebestsurfaceisalevel concrete pad. A spa, full of water, can weigh a great deal. Please ensure the spot can support the weight.• Makesuretolevelyourspabeforefillingit.• Locatetheequipmentpanel.Thesystempack,drainvalve,owner’smanual and optional ozone generator are usually located all in the same area.

Be sure that the connections are tightened during draining. Water inside the system pack will cause the pack to fail and the breaker to trip.

• Thepanels,onallfoursides,areremovable.Besuretohaveaccessonall four sides.• Besuretohaveeasyaccesstothecircuitbreakerinthesubpanel(240volt

models).• Neverletwaterintothesubpanel(240voltmodels), or into the electrical outlet that your spa is plugged in to. Your 240 volt spa’s sub panel is rain

tight when installed correctly with the door closed.

3. INSTALLATION - PLACING YOUR SPAOutdoor and patio installationTo position the spa correctly in your backyard is very important. The reason is your spa’s warranty. The warranty on a spa is voided if the site is not level. If you install your hot tub outdoors, a concrete pad is the best method for a stable and level surface. The con-crete pad should be four inches thick. Your spa may be installed on a deck, providing the load rating can handle a full spa with people in it.

Deck installation When placing the spa on a deck, please ensure the maximum load capacity of the deck. Consult a quali-fied deck builder or structural engineer before you place the hot tub on an elevated deck or indoors. To determine the weight of your hot tub, please refer to the specifications on the website. This weight must not exceed the structural weight of the deck.

Pre-Delivery Guide6

Indoor installation When installing a spa indoors, there are some special considerations. The combination of heat and moisture will accumulate on the floor and surrounding the spa. The flooring material needs to provide a grip when wet. The location also needs proper drainage to prevent water build-up around the spa. When building a room for your spa, it is best to have a floor drain installed. The humidity of a room with a spa can become a problem if there is not enough proper ventilation. Otherwise, problems such as dry rot, mildew or other problems may occur.

Ground preparation Your spa has been engineered to rest on a variety of surfaces. The insulated spa floor base gives you the ability to find the perfect place. A concrete slab is the best for long term. There are other options available as long as the surface is level prior to delivery. The alternatives are 5/8 minus crushed packed rock, or a deck that is rated for the load.

Brick pavers

Cement

Decorative cement, stained

Packed/crushed gravel: 5/8” minus

Stone, slate, granite

Decking: wood, synthetic

Decorative cement & bricks

Marble, travertine

When placing a spa on crushed rock, the easiest way to maintain its form is to build a frame and fill it with the crushed packed rock. Remember, if the spa is placed on grass or dirt, debris will get inside the spa as the users enter and exit.

It is incredibly important to the operation and the draining of the tub for the tub to be level once it is installed. Failure to have the spa level prior to adding water can af-fect the warranty.


4. ELECTRICAL HOOK-UP REQUIREMENTS - 240VRemoving spa panels

1. Remove the plastic ‘tap-cap’ decorative screw head covers from screws on access spa panel.

2. Unscrew the screws from the access spa panel.

3. Remove the spa panel for access to spa com-ponents. Reverse these steps to attach the spa panel.

Electrical connections by licensed personnelTo ensure you will have an opportunity to use your hot tub soon after delivery, it is very important that the required electrical service has been installed.

IMPORTANT: Electrical connections must be made by qualified, licensed personnel. Please contact a licensed residential electrician for these services.

All models require a 50 amp single phase, 240 volt circuit breaker in the main electrical service panel. NOTE: WE RECOMMEND THAT A SUB PANEL BE USED TO SUPPLY POWER AND PROTECT THE SPA. All 240 volt Clearwater spas must be wired in accordance with applicable local electrical codes, and all electrical work must be done by a licensed elec-trician. A licensed electrician should install a four-wire electrical service (two line voltages, one neutral, one ground) from the main electrical service panel to the sub-panel, and from the sub-panel to the spa per the appropriate wiring diagram as illustrated below. The grounding con-ductor must be at least #6 AWG. Your electrician should mount the sub-panel in the vicinity of the spa but it should not be closer than five (5) feet from the spa’s water edge (NEC 680-38 to 41-A-3).

WARNING: Removing or bypassing the GFCI breakers in the sub panel at any time will result in an unsafe spa and will void the warranty.

WIRE SPECIFICATION NOTE:Longelectricalrunsmayrequirealarger gauge feed wire than stated. We recommend that a maximum voltage drop of 3% be used when calculat-ing the larger wire size.

Refer to the Wiring Diagrams (figure 1-1) for the electrical requirements of the 240 volt models.

Do not turn on power to the spa when the tub is not filled.

The closer you locate the spa

to the main service panel,

the less money you will have to spend on wire.

Wire can become expensive if you

run long lengths.

Always shut offpower at thesource when

working with anyelectrical power!!Failure to do this

could result inserious injury or

even death!

Pre-Delivery Guide8

ELECTRICAL REQUIREMENTS - 240V (cont.)

IMPORTANT: Electrical connections must be made by qualified, licensed personnel. Please contact a licensed residential electrician for these services.

Figure 1-1240 volt wiring configuration from the house to the spa


ENERGY EFFICIENCY GREEN TECHNOLOGY

Providing a greener spa.Clearwater Spas is strongly committed to protecting the health of our environment and manufacturing energy efficient hot tubs that help to conserve our natural resources. We strive to provide clean air, clean water and recycling solutions in our manufacturing process and the components that go into our spas.

E-Smart TechnologyYour spa is made with ‘e-smart or eco technology’ built into every hot tub to provide a complete energy efficient system. From the initial engineering design stage through our manufacturing, recycling and product usage, we have set a high standard to keep our hot tubs environmentally sound. This symbol signifies the highest energy efficiencies, the smartest engineering detail standards, global environmentally green components and e-cycling sound programs. Energy E�cient

CEC Certi�edRecycling ProgramRecycled ABS Floor

ManufacturingFactory Process

Clean WaterNatural Solutions

Clean AirEco Shell Spray

Certi�edEnergy E�ciency

CEC


CECEnergy EfficientClearwater Spas RTB (reflective thermal barrier) rigid insulation is 12% more energy efficient than spray foam insulation. Our insulation panels reflect and recycle heat from within the cabinet keeping it warm and dry. Energy E�cient






CEC


CECCalifornia Energy Commission (CEC) CertifiedAll of Clearwater Spas are certified to California’s Energy Commission (CEC) – the most stringent energy efficiency standards in the United States. We not only meet these standards – we exceed them. Energy E�cient






CEC


CECRecycling & E-cyclingClearwater Spas takes pride in using 100% recycled ABS to fabricate our in-sulated Durafloors on all of our spas. We also recycle 100% of our wood, plastic and cardboard waste. Energy E�cient






CEC


CECHealthy Factory ProcessWe are focused on providing healthy and safe solutions in our factory for our employees and our environment. This includes processes for good air quality, recycled and energy efficient components. Energy E�cient






CEC


CECClean Air FactoryOur Eco-Spray™ process for strengthening every spa shell has 0% styrene, no odor and emits no VOC’s (volatile organic compounds) for a cleaner air environment. Energy E�cient






CEC


CECClean Water SolutionsWe provide cutting edge clean water sanitizing solutions to help provide natural alternatives and help reduce the need for chemicals. Salt water, UV-C light, ozone and re-usable filters provide natural clean water solutions.

Pre-Delivery Guide

Resort Series

10

Jet designs, jet locations and pump locations are subject to change without notice.

OrlandoDIMENSIONS

Note: All dimensions are approximate. Measure yourspa before making critical design or pathway decisions.

31" (78.7 cm)

92.5" (235 cm)Ground Contact 86" (218.4 cm)

92.5

" (23

5 cm

)

Gro

und

Cont

act 8

6" (2

18.4

cm

)

EKEK

(Euro Pump #4)

Pump #3

Circ.Pump

Pump #2Pump #1

Subwoofer

8" (2

0 cm

)

3.5" Dia.(8.9 cm)

Equipment AccessSalt System ElectrodeTopside ControlSalt System Control

Topside Control

Pre-Delivery Guide

Resort Series

11


MonacoDIMENSIONS


Topside Control

31" (78.7 cm)


92.5

" (23

5 cm

)

Gro

und

Cont

act 8

6" (2

18.4

cm

)

Pump #3

Pump #2Pump #1

Subwoofer

EKEK 3.5" Dia.(8.9 cm)

8" (2

0 cm

)


Circ.Pump(Euro)

Pump #4(Euro)

Circ. Pump(U.S./Canada)

Pre-Delivery Guide

Resort Series

12


CaboDIMENSIONS


Topside Control

27" (68.6 cm)

84" (213.4 cm)Ground Contact 76" (193 cm)

84" (

213.

4 cm

)

Gro

und

Cont

act 7

6" (1

93 c

m)

(EuroCirc.

Pump)

Circ.Pump(Euro

Pump #1)

Pump #1(Euro

Pump #2)

Pump #3(Euro

Pump #4)

Pump #2(Euro

Pump #3)


8" (2

0 cm

)


Subw

oofe

r

Pre-Delivery Guide

Resort Series

13


RioDIMENSIONS


27" (68.6 cm)

75" (190.5 cm)Ground Contact 71" (180.3 cm)

84" (

213.

4 cm

)

8" (2

0 cm

)

Gro

und

Con

tact

78"

(198

cm

)

EK 3.5" Dia.(8.9 cm)EK

Pump #1(Euro

Pump #2)

Pump #2(Euro

Pump #3)

(EuroPump #1)

Subw

oofe

r


Circ.Pump

Topside Control

Pre-Delivery Guide

Beachcraft Series

14


Pearl IslandDIMENSIONS


31" (78.7 cm)


92.5

" (23

5 cm

)

Gro

und

Cont

act 8

6" (2

18.4

cm

)

Salt System Electrode

Pump #1(Euro

Pump #1)

(Euro Pump #3)

Circ.Pump


8" (2

0 cm

)

Pump #2(Euro

Pump #2)

Equipment AccessTopside ControlSalt System Control

Subwoofer

Topside Control

Pre-Delivery Guide

Beachcraft Series

15


TraditionDIMENSIONS


31" (78.7 cm)


92.5

" (23

5 cm

)

Gro

und

Cont

act 8

6" (2

18.4

cm

)

(Euro Pump #3)Circ. Pump

EKEK3.5" Dia.(8.9 cm)

8" (2

0 cm

)

Pump #1(Euro

Pump #1)

Pump #2(Euro

Pump #2)

Salt System ControlSalt System ElectrodeTopside ControlEquipment Access

Subw

oofe

r

Topside Control

Pre-Delivery Guide

Beachcraft Series

16


St. AndrewDIMENSIONS


27" (68.6 cm)

84" (235 cm)Ground Contact 78" (198.1 cm)

84" (

235

cm)

Gro

und

Cont

act 7

8" (1

98.1

cm

)

Circ. Pump

Pump #2(Euro

Pump #2)

(Euro Pump #3)


8" (2

0 cm

)

Pump #1(Euro

Pump #1)


Subwoofer

Topside Control

Pre-Delivery Guide

Beachcraft Series

17


Myrtle BeachDIMENSIONS


27" (68.6 cm)

84" (235 cm)Ground Contact 78" (198.1 cm)

84" (

235

cm)

Gro

und

Cont

act 7

8" (1

98.1

cm

)

Circ. Pump

(Euro Pump #3)


8" (2

0 cm

)

Pump #1(Euro

Pump #1)

Pump #2(Euro

Pump #2)


Subwoofer

Topside Control

Pre-Delivery Guide

XS Series

18


XS93LDIMENSIONS


31" (78.7 cm)


92.5

" (23

5 cm

)

Gro

und

Cont

act 8

4" (2

13.4

cm

)

Pump #1(Euro

Pump #1)

Circ. Pump

EKEK

8" (2

0 cm

)

Pump #2(Euro

Pump #2)(Euro Blower)

Subw

oofe

r


3.5" Dia.(8.9 cm)

Topside Control

Pre-Delivery Guide

XS Series

19


XS93NLDIMENSIONS


31" (78.7 cm)


92.5

" (23

5 cm

)

Gro

und

Cont

act 8

4" (2

13.4

cm

)

Pump #1(Euro

Pump #1)

Pump #2(Euro

Pump #2)

Circ. Pump

EKEK

8" (2

0 cm

)

(Euro Blower)

Subw

oofe

r


3.5" Dia.(8.9 cm)

Topside Control

Pre-Delivery Guide

XS Series

20


XS84LDIMENSIONS


27" (68.6 cm)


84" (

213.

4 cm

)

Gro

und

Cont

act 7

6" (1

93 c

m)

Pump #2(Euro

Blower)

(Euro Pump #2)

Pump #1(Euro

Pump #1)

Circ.Pump

EKEK

8" (2

0 cm

)

3.5" Dia.(8.9 cm)

Equipment AccessSalt System ElectrodeSalt System ControlTopside Control

Subw

oofe

r

Topside Control

Pre-Delivery Guide

XS Series

21


XS84NLDIMENSIONS


27" (68.6 cm)


84" (

213.

4 cm

)

Gro

und

Cont

act 7

6" (1

93 c

m)

Pump #2(Euro

Blower)

(Euro Pump #2)

Pump #1(Euro

Pump #1)

Circ.Pump

EKEK

8" (2

0 cm

)

3.5" Dia.(8.9 cm)

Equipment AccessSalt System ControlTopside ControlSalt System Electrode

Subw

oofe

r

Topside Control

Pre-Delivery Guide

XS Series

22


XS76LDIMENSIONS


76" (193 cm)Ground Contact 72" (183 cm)

76" (

193

cm)

Gro

und

Cont

act 7

2" (1

83 c

m)

Circ.Pump

25" (64 cm)

EKEK

8" (2

0 cm

)

Pump #1(Euro

Pump #1)

Pump #2(Euro

Blower)

(Euro Pump #2)


3.5" Dia.(8.9 cm) Su

bwoo

fer

Topside Control

Pre-Delivery Guide

XS Series

23


XS76NL Note: All dimensions are approximate. Measure your

spa before making critical design or pathway decisions.


76" (

193

cm)

Gro

und

Cont

act 7

2" (1

83 c

m)

Circ.Pump

25" (64 cm)

EKEK

8" (2

0 cm

)

Pump #1(Euro

Pump #1)

Pump #2(Euro

Blower)

Subw

oofe

r


3.5" Dia.(8.9 cm)

(Pump #1if Gold)(Euro

Pump #2)

Topside Control

Pre-Delivery Guide

XS Series

24


XS76CCDIMENSIONS


23" (58.4 cm)


77" (

193

cm)

Gro

und

Cont

act 6

9" (1

75 c

m)

TopsideControl

Circ.Pump

Salt System Electrode

EK

Approx. 3

6" (91 cm

)

Pump #2(Euro

Pump #2)

Pump #1(Euro

Pump #1)

(Euro Blower)

EK3.5" Dia.(8.9 cm)

8" (2

0 cm

)

8" (20 cm)

Salt SystemControl

Box

3.5" Dia.(8.9 cm)

Subw

oofe

r

Topside Control

Pre-Delivery Guide

XS Series

25


XS76R - with RIM CabinetNote: All dimensions are approximate. Measure your


Topside Control


76" (

193

cm)

24" (

61 cm

)

Gro

und

Cont

act 6

9" (1

75 c

m)

Topside Control

Salt SystemControl

Box

EquipmentAccess

SaltSystem

Electrode

27" (68.6 cm)

Pump #1(Euro

Pump #1)

(Euro Blower)

Pump #2(Euro

Pump #2)

Circ.Pump

8" (2

0 cm

)

EK 3.5" Dia.(8.9 cm)

Pre-Delivery Guide

XS Series

26


XS76R - with Cedar CabinetNote: All dimensions are approximate. Measure your


Topside Control


76" (

193

cm)

24" (

61 cm

)

Gro

und

Cont

act 6

9" (1

75 c

m)

Equipment AccessTopside ControlSalt System Control Box

SaltSystem

Electrode

27" (68.6 cm)

Pump #1(Euro

Pump #1)

(Euro Blower)

Pump #2(Euro

Pump #2)

Circ.Pump

8" (2

0 cm

)

EK 3.5" Dia.(8.9 cm)

Pre-Delivery Guide

XS Series

27


XS76TNote: All dimensions are approximate. Measure your


Topside Control

Topside ControlEquipment AccessSalt System Control Box

92" (234 cm)

89.5" (227 cm)

76" (193 cm

)

Ground Conta

ct 73.5" (

187 cm)

76" (193 cm)

Ground Contact 73.5" (187 cm)

Pump #1(Euro

Pump #1)

Circ.Pump

(Option)

Pre-Delivery Guide

XS Series

28


XS76L Eco Note: All dimensions are approximate. Measure your



76" (

193

cm)

Gro

und

Cont

act 7

2" (1

83 c

m)

Pump #1

Circ. Pump Opt.

25" (64 cm)

EKEK

8" (2

0 cm

)


3.5" Dia.(8.9 cm)

Topside Control

Pre-Delivery Guide

XS Series

29


XS76NL EcoDIMENSIONS



76" (

193

cm)

Gro

und

Cont

act 7

2" (1

83 c

m)

Pump #1

Circ. Pump Opt.

25" (64 cm)

EKEK

8" (2

0 cm

)


3.5" Dia.(8.9 cm)

Topside Control

Pre-Delivery Guide30

NOTES FOR YOUR HOT TUB

Contractor Suggestions

Electrician Name: __________________________________________ Telephone: __________________________________________ Name: __________________________________________ Telephone: __________________________________________

Masonry Name: __________________________________________ Telephone: __________________________________________ Name: __________________________________________ Telephone: __________________________________________

General Name: __________________________________________ Telephone: __________________________________________ Name: __________________________________________ Telephone: __________________________________________

Services Available From Your Clearwater Spas Dealer

SERVICE CHECKLIST AND ANY COSTS Pre-Delivery site inspection £_____________ Deliver spa to installation site £_____________ Unwrap spa and haul away packaging material £_____________ Set up and level spa £_____________ General spa operation and maintenance orientation £_____________ Water quality and maintenance operation £_____________ Adjust the water’s Total Alkalinity, Calcium Hardness and pH £_____________ Sanitize the water £_____________ Inspect the spa cover, place on spa £_____________ Review winterizing instructions £_____________ Review Owner’s Manual £_____________ Follow-up call £_____________ In-store water analysis £_____________

Total Costs ________________


NOTES FOR YOUR HOT TUB

Additional Products That May Be Available From Your Clearwater Spas Dealer

£ Salt Sanitation System

£ CleanLightUV-CSanitationSystem

£ CD Ozone Generator

£ Nature 2 Sticks

£ Nature 2 test strips

£ Stain and Scale Remover

£ Filter Cleaner

£ Ph-Alkalinity Up

£ Ph-Alkalinity Down

£ Concentrated Chlorinating Granules

£ Defoamer

£ Calcium Hardness Increaser

£ 4-way test strips

£ Coverlift

£ Cover Rock-It

£ Vinyl covers

£ Spa vacuums

£ Spa steps

£ Stain kits

£ Replacement filter cartridges

£ Pillows

Pre-Delivery Guide32

NOTES:


NOTES:

18800 Woodinville/Snohomish Rd.P.O. Box 2140

Woodinville, WA 98072

1.800.791.1190Phone: 425.483.1877

Fax: 425.487.1148


pre-delivery guide 4-1-14

Clearwater Spas environmental commitmentbegins with our exclusive E-Smart™ Technology


CEC

Documents

Pre-Delivery Guide - Clearwater Spas Guide. Congratulations on your decision to purchase a spa. Clearwater Spas manufacturers the best built and most energy efficient spas in the industry