Stage 3: PROTECT - G3 Wax (for fully cured paint)

Farécla Products Ltd | +44 (0) 1920 465 041 | enquiries@farecla.com | www.farecla.com

For All Paint Systems (including the very latest energy or ‘hyper’ clearcoats)

Premium High Cut System Process Chart

LIT1

914

(V2

11-2

016)

Stage 1: CUT

Stage 1:CUT

CodesG3P506G3P101

Product Size500g1kg

Abrasive CompoundG3 Premium

ApplicatorsG Mop 6” High Cut FoamG Mop 8” High Cut Foam

CodesGMC618GMC818

If swirl marks or holograms remain, use the same process as in Stage 1: CUT but with a G Mop Finishing Foam and a small quantity of G3 Premium at 800 - 1100rpm.

Stage 1: CUT

The G Mop High Cut Foam is �exible which follows to contours of the bodywork providing a safe, powerful cut and high shine �nish evenly.

Stage 2: FINISH (if desired on darker colours)

Stage 3: PROTECT - G3 Glaze (for fresh paint)

Stage 2: FINISH (if desired)

ApplicatorsG Mop 3” Finishing FoamG Mop 6” Finishing FoamG Mop 8” Finishing Foam

CodesGMF301GMF601GMF801

Stage 3: PROTECT

CodesG3G501G3G101G3G118

Product Size500ml1 ltr1 US gallon

CodesG3W501G3W106G3W118

Product Size500ml1 ltr1 US gallon

Gloss EnhancerG3 Glaze

Premium LiquidProtection

G3 Wax

Applicators for both productsG Mop 3” Finishing FoamG Mop 6” Finishing FoamG Mop 8” Finishing FoamFinishing Cloth (3 x cloths)

CodesGMF301GMF601GMF801

FC-3

Stage 2:FINISH

Stage 3:PROTECT

Attach a G Mop Back Plate anda G Mop Finishing Foam to a polisher

1

Polish at800 - 1100rpm

3

Shake bottle welland apply a smallquantity to the pad

2

SHA

KE POU

R

ATTACH 800 - 1100rpm

Wipe clean with aFinishing ClothFC-3 (3 x cloths)

4

Tip: Prior to �rst use of a new pad, roughen with a Spurring Brush (1090005) to ensure optimum results. Clean pad with the Spurring Brush a�er use.

Compound at LOW SPEED

4

900 - 1300rpm

Wipe clean with aFinishing ClothFC-3 (3 x cloths)

5

Wipe clean with aFinishing ClothFC-3 (3 x cloths)

4

Shake bottle welland apply a smallquantity to thesurface or cloth

1

SHA

KE POU

R

Rub the product ina circular motiononto the surface

2

Allow to dry to ahaze

3

- G3 Wax (for fully cured paint)

Wipe clean with aFinishing ClothFC-3 (3 x cloths)

4

Rub the product ina circular motiononto the surface

Allow to dry to ahaze

3

Attach a G Mop Back Plate anda G Mop High Cut Foam to a polisher

1

Shake bottle wellbefore use

2

SHAKE

Dispense a small quantity of product ontosurface or pad

3

POU

R

ATTACH

OR

Applicator Back Plates

G Mop Flexible Back Plate for 6” PadsGMB146 (14mm thread size)GMB586 (5/8” thread size)GMB166 (16mm thread size)

G Mop Flexible Back Plate for 8” PadsGMB814 (14mm thread size)GMB858 (5/8” thread size)GMB816 (16mm thread size)

PREMIUMABRASIVE

COMPOUNDFor cutting, �nishing or both

CodesG3P506G3P101

Product Size500g1kg

Abrasive CompoundG3 Premium

OR OR

Remove Defect

Inspect defect

Remove defect - P1500