Stage 3: PROTECT - G3 Wax (for fully cured paint)
Farécla Products Ltd | +44 (0) 1920 465 041 | [email protected] | www.farecla.com
For All Paint Systems (including the very latest energy or ‘hyper’ clearcoats)
Premium High Cut System Process Chart
LIT1
914
(V2
11-2
016)
Stage 1: CUT
Stage 1:CUT
CodesG3P506G3P101
Product Size500g1kg
Abrasive CompoundG3 Premium
ApplicatorsG Mop 6” High Cut FoamG Mop 8” High Cut Foam
CodesGMC618GMC818
If swirl marks or holograms remain, use the same process as in Stage 1: CUT but with a G Mop Finishing Foam and a small quantity of G3 Premium at 800 - 1100rpm.
Stage 1: CUT
The G Mop High Cut Foam is �exible which follows to contours of the bodywork providing a safe, powerful cut and high shine �nish evenly.
Stage 2: FINISH (if desired on darker colours)
Stage 3: PROTECT - G3 Glaze (for fresh paint)
Stage 2: FINISH (if desired)
ApplicatorsG Mop 3” Finishing FoamG Mop 6” Finishing FoamG Mop 8” Finishing Foam
CodesGMF301GMF601GMF801
Stage 3: PROTECT
CodesG3G501G3G101G3G118
Product Size500ml1 ltr1 US gallon
CodesG3W501G3W106G3W118
Product Size500ml1 ltr1 US gallon
Gloss EnhancerG3 Glaze
Premium LiquidProtection
G3 Wax
Applicators for both productsG Mop 3” Finishing FoamG Mop 6” Finishing FoamG Mop 8” Finishing FoamFinishing Cloth (3 x cloths)
CodesGMF301GMF601GMF801
FC-3
Stage 2:FINISH
Stage 3:PROTECT
Attach a G Mop Back Plate anda G Mop Finishing Foam to a polisher
1
Polish at800 - 1100rpm
3
Shake bottle welland apply a smallquantity to the pad
2
SHA
KE POU
R
ATTACH 800 - 1100rpm
Wipe clean with aFinishing ClothFC-3 (3 x cloths)
4
Tip: Prior to �rst use of a new pad, roughen with a Spurring Brush (1090005) to ensure optimum results. Clean pad with the Spurring Brush a�er use.
Compound at LOW SPEED
4
900 - 1300rpm
Wipe clean with aFinishing ClothFC-3 (3 x cloths)
5
Wipe clean with aFinishing ClothFC-3 (3 x cloths)
4
Shake bottle welland apply a smallquantity to thesurface or cloth
1
SHA
KE POU
R
Rub the product ina circular motiononto the surface
2
Allow to dry to ahaze
3
- G3 Wax (for fully cured paint)
Wipe clean with aFinishing ClothFC-3 (3 x cloths)
4
Rub the product ina circular motiononto the surface
Allow to dry to ahaze
3
Attach a G Mop Back Plate anda G Mop High Cut Foam to a polisher
1
Shake bottle wellbefore use
2
SHAKE
Dispense a small quantity of product ontosurface or pad
3
POU
R
ATTACH
OR
Applicator Back Plates
G Mop Flexible Back Plate for 6” PadsGMB146 (14mm thread size)GMB586 (5/8” thread size)GMB166 (16mm thread size)
G Mop Flexible Back Plate for 8” PadsGMB814 (14mm thread size)GMB858 (5/8” thread size)GMB816 (16mm thread size)
PREMIUMABRASIVE
COMPOUNDFor cutting, �nishing or both
CodesG3P506G3P101
Product Size500g1kg
Abrasive CompoundG3 Premium
OR OR
Remove Defect
Inspect defect
Remove defect - P1500
Recommended
