PRICE SCHEDULE 1.0 VENDOR TO PROVIDE Box FOLLOWING …

PRICE SCHEDULE 1.0 VENDOR TO PROVIDEBox FOLLOWING DETAIL

Box Make and Model Henderson 10’ Mark E-SA 24/32

List truck type box fits Single axle, 84" useable CA is recommended

Box style Unibody design, crossmemberless (Western style)

Width & length of box 10ft. box with 84" inside width, 96" outside width

Side panel description 24" high, fully welded, 10 ga. grade 50 Hi-tensilesteel, fully boxed-in & fully welded top rails, rub rails are sloped for dirt & debris shedding

Front panel description 52" high, 10 ga. construction. Boxed top rail and boxed center brace. 2" sideboard pockets.

Floor description One piece, 3/16" HSLA grade 50 steel floor-65,000 PSI tensile strength, 4" formed in floor to side radius

Corner post description Rear corner post, 7 ga. steel, 5-3/4" x 12", full depth, tied to 8" deep structural channel rear apron. Contoured front corner post

Under structure description Two 5" structural steel I-beam long sills (with tele hoist)"No splices", crossmemberless- (8" for UB hoist),

Tailgate description 32" high, one piece 10 ga. sheet. Extra deep braces. Full perimeter boxing with sloped horizontal brace & top rail. 10 ga. sloped horizontal brace, flush with perimeter boxing(2 panel design) 3/4" latch hooks with 3/8" latch plates. 1-1/4" upper & lower pins. Air trip release kit with double over-center linkage (air over air) (brake chamber type, not cylinder operated)

Hinge Description Upper tailgate hinges are 1” thick flame cut

Description of peripheral items LED Stop/turn/tail lights and side clearance lights are (lights, access steps, etc.) mounted in rear corner post. Rubber mounted,

shock resistant ICC, 3-light cluster is also included. Front & rear mud flaps included. Pullout type ladder with box step and grab handle, mounted front drivers side on underside of dump body. All electrical wiring connections will be put in heat shrink tubing & will run to a sealed junctionbox.

Warranty Info One Year Warranty, parts and labor

Is installation included in price? "Yes" Yes, to an acceptable hoist type

Is box painted? "Yes" Yes, epoxy primed and top coated with an acrylic urathane paint to customers choice (one standard fleet color), bottom side painted black

TOTAL PRICE (Installed): $10,946.00

1.1 - Air operated tailgate latch, air over air, brake chamber type, in lieuof manual type trip

Price: Std.

1.2 - Box Vibrator - Make & Model - Cougar model 2700Price: $619.00

1.2A Installation of Box VibratorPrice: $546.00

1.3 - 3/16” AR400 floor, 200,000 PSI tensile, in lieu of standard 3/16” grade 50, 65,000 PSI tensile

PRICE $528.00


PRICE $798.00

1.5 - 38” tailgate in lieu of 32” tailgate (reccomend UB-8-17 or tele hoist)PRICE $165.00

1.6 - 30” sides and 38” tailgate in lieu of 24” sides and 32” tailgate (requires UB-8-17 or tele hoist)

PRICE $88.00

1.7 - 24" 7 ga. sides and ends in lieu of 10 ga.PRICE $225.00

1.8 - 7 ga. tailgate in lieu of 10 ga.PRICE $78.00

1.9 - 30" 7 ga. sides & ends in lieu of 10 ga (24" sides)PRICE $280.00

1.10 - 3/16' AR400 sides & ends in lieu of 10 ga. Grade 50 (24" sides)PRICE $1,596.00

1.11 - 3/16” AR400 sides & ends in lieu of 10 ga. Grade 50 (30" sides)PRICE $1,782.00

1.12 - Mark "E" Asphalt style sloped rear & tailgatePRICE $767.00

1.13 - One piece sloping sides (includes 1 top rail, 2 intermediateside braces, and 1 bottom rub rail)- 10 ga. carbon steel- in lieu of std.

PRICE $770.00


PRICE $1,042.00

1.15 - One piece sloping sides (includes 1 top rail, 1 intermediateside braces, and 1 bottom rub rail)- 3/16" AR400 steel- in lieu of std.

PRICE $1,316.00

1.16 - 409 stainless steel front & rear corner post, all side bracing, tailgate bracing, and apron in lieu of standard

PRICE $960.00 1.17 - 409 stainless steel rear corner post & apron only, in lieu of std.

PRICE $290.00

1.18 - 409 stainless steel rear corner post only, in lieu of std.PRICE $202.00

1.19 - 3 panel tailgate in lieu of 2 panelPRICE $78.00

1.20 - 6 panel tailgate in lieu of 2 panel PRICE $168.00

1.21 - Extra tailgate bracing in 409SS in lieu of std. (3 or 6 panel) PRICE $148.00

1.22 - 3/4" rebar down both sides for walk/tarp railPRICE $140.00

1.23 - 1-1/2", grip strut down both sides for walk railPRICE $150.00

1.24 - 10-1/2' dump body with 5" I-beams (for tele hoist), in lieu of 10' body(note: can also use UB-8-17 hoist with 8" I-beams or 8-21 hoist with 10" I-beams)

PRICE $260.00

1.25 - Elliptical body sides in lieu of square body sides (add 30" sides & 3/16" AR400 sides & ends) (deduct)PRICE ($250.00)

Delivery Starting Point Address N15921 Schubert Rd., Galesville, WI 54630

Cost per loaded mile for pickup and or delivery of vehicle (if applicable):Cost per loaded mile for delivery of truck, Vendor supplies fuel $4.90

Cost per loaded mile for delivery of truck, Customer supplies fuel $4.00

VENDOR: UNIVERSAL TRUCK EQUIPMENTCONTACT PERSON: DONNIE BJORGEADDRESS: N15921 SCHUBERT RD., GALESVILLE, WI 54630PHONE NO.: 608-539-4600FAX NO.: 608-539-4800 E-MAIL ADDRESS: [email protected]




















PRICE Std.

1.2 - Box Vibrator - Make & Model - Cougar model 2700PRICE $619.00

1.2A Installation of Box VibratorPRICE $546.00


PRICE $615.00


PRICE $960.00

1.5 - 38” tailgate in lieu of 32” tailgate (requires UB-8-21 or tele hoist)PRICE $165.00


PRICE $108.00








PRICE $847.00


PRICE $1,146.00


PRICE $1,426.00


PRICE $1,056.00 1.17 - 409 stainless steel rear corner post & apron only, in lieu of std.

PRICE $290.00





1.22 - 3/4" rebar down both sides for walk/tarp railPRICE $149.00

1.23 - 1-1/2", grip strut down both sides for walk railPRICE $165.00

1.24 - 11-1/2' dump body with 5" I-beams (for tele hoist), in lieu of 11' body(note: can also use UB-8-21 hoist with 10" I-beams)

PRICE $345.00

























PRICE Std.




PRICE $675.00


PRICE $1,075.00



PRICE $108.00








PRICE $895.00


PRICE $1,196.00


PRICE $1,604.00


PRICE $1,152.00 1.17 - 409 stainless steel rear corner post & apron only, in lieu of std.

PRICE $290.00





1.22 - 3/4" rebar down both sides for walk/tarp rail (MS)PRICE $162.00

1.23 - 1-1/2", grip strut down both sides for walk rail (M/S)PRICE $180.00

1.24 - Flush sides and tailgate (No Charge)PRICE $0.00







Box Make and Model Henderson 10’ Mark E-SA-SS 24/32, 201 Stainless Steel


Box style Unibody design, crossmemberless (Western style)201 stainless steel sides, headsheet, tailgate and all perimeter bracing, front & rear corner posts & rear apron


Side panel description 24" high, fully welded, 10 ga. 201 stainless steel, fully boxed-in & fully welded top rails, rub railsare sloped for dirt & debris shedding

Front panel description 52" high, 10 ga. 201 S/S construction. Boxed top rail & center brace. 2" sideboard pockets.

Floor description One piece, 3/16" AR400 steel floor-200,000 PSItensile strength, 4" floor to side radius

Corner post description Rear corner post, 7 ga. 201 S/S, 5-3/4" x 12", full depth, tied to 8" deep structural channel rear apron. Contoured front corner post


Tailgate description 32" high, one piece 10 ga. 201 S/S sheet. Extradeep braces. Full perimeter boxing with sloped horizontal brace & top rail. 10 ga. 201 S/S sloped horizontal brace, flush with perimeter boxing(2 panel design) 3/4" latch hooks with 3/8" latch plates. 1-1/4" upper & lower pins. Manual release with double over-center linkage



shock resistant ICC, 3-light cluster is also included. Front & rear mud flaps included. Pullout type ladder with box step and grab handle, mounted front drivers side on underside of dump body. All electrical wiring connections will be put inheat shrink tubing & will run to a sealed junction box



Is box painted? "No" Unpainted dump body- left in it's natural state.Bottom side & truck frame painted black



PRICE Std.



1.3 - 1/4” AR400 floor, 200,000 PSI tensile, in lieu of standard 3/16” AR400

PRICE $270.00



PRICE $290.00

1.6 - 7 ga. 201 S/S sides and header in lieu of 10 ga. 201S/S (24" sides)PRICE $945.00

1.7 - 7 ga. 201 S/S sides and header in lieu of 10 ga. 201S/S (30" sides)(must add 30" sides option- 1.5)

PRICE $885.00

1.8 - 7 ga. 201 S/S tailgate in lieu of 10 ga. 201 S/SPRICE $262.00

1.9 - 3 panel S/S tailgate in lieu of 2 panel S/SPRICE $593.00


1.11 - 3/4" 201 S/S round stock down both sides for tarp railPRICE $260.00

1.12 - 1-1/2", 201 S/S grip strut down both sides for walk railPRICE $270.00

1.13 - One piece sloping sides (includes 1 top rail, 2 intermediate sidebraces, and 1 bottom rub rail)- 10 ga. 201 stainless steel

PRICE $1,184.00

1.14 - One piece sloping sides (includes 1 top rail, 2 intermediate sidebraces, and 1 bottom rub rail)- 7 ga. 201 stainless steel- in lieu of std.

PRICE $1,397.00

1.15 - 10ga. 304 stainless steel dump body in lieu of 10 ga.201 stainless steel (with 24" sides)

PRICE $680.00


PRICE $906.00

1.17 - 7ga. 304 stainless steel dump body in lieu of 7 ga. 201 stainlesssteel (with 24" sides) (must add 7ga. 201 S/S option above)

PRICE $746.00


PRICE $880.00

1.19 - 10-1/2' dump body with 5" I-beams (for tele hoist), in lieu of 10' body(note: can also use UB-8-17 hoist with 8" I-beams or 8-21 hoist with 10" I-beams)

PRICE $638.00

1.20 - Elliptical body sides in lieu of square body sides (add 30" sides & 7ga. sides & ends) (deduct)PRICE ($400.00)
























PRICE Std.



1.3 - 1/4” AR400 floor, 200,000 PSI tensile, in lieu of standard3/16” AR400

PRICE $345.00



PRICE $315.00



PRICE $895.00







PRICE $1,317.00


PRICE $1,550.00


PRICE $690.00


PRICE $740.00


PRICE $820.00


PRICE $910.00

1.19 - 11-1/2' dump body with 5" I-beams (for tele hoist), in lieu of 11' body(note: can also use UB-8-21 hoist with 10" I-beams)

PRICE $638.00

























PRICE Std.



1.3 - 1/4” AR400 floor, 200,000 PSI tensile, in lieu of standard 3/16” AR400

PRICE $400.00



PRICE $360.00



PRICE $924.00







PRICE $1,424.00


PRICE $1,685.00


PRICE $990.00


PRICE $1,050.00


PRICE $900.00


PRICE $998.00







Box Make and Model Henderson Mark E -ti (XD) 36/44 (13’-16’)

List truck type box fits Tandem axle only


Width & length of box 13' box length & 96" outside width, 84" inside width


Front panel description 60" high, 10 ga. construction. Boxed top rail, 12" internal doghouse

Floor description One piece, 3/16" AR400 steel floor-200,000 PSI tensilestrength, 45 degree floor to side knee-brace formed into floor

Corner post description Rear corner post, 7 ga. steel, 5-3/4" x 12", full depth, tied to 8" deep structural channel rear apron. Contoured front corner post and 2" sideboard pockets

Under structure description Two 8" structural steel I-beam long sills with"No splices" (8" x 13.0 lbs./ft.), crossmemberless


Hinge Description Flush mount 1/2" flame-cut pivots. Heavy-duty 1" flame cut hinge plates.








PRICE Std.



1.3 - Mark E Asphalt body style (includes sloped tailgate)PRICE $180.00

1.4 - 13-1/2’ or 14’ dump body in lieu of 13’PRICE $326.00


1.6 - 15-1/2' and 16’ dump body in lieu of 13’PRICE $713.00

1.7 - 44” sides and 52” tailgate in lieu of 36” sides & 44” tailgate (13' and 14' bodies)

PRICE $197.00


PRICE $227.00

1.9 - 1/4” AR400 floor, 200,000 PSI tensile, in lieu of standard 3/16” AR400 floor (13' body)

PRICE $440.00


PRICE $475.00


PRICE $515.00


PRICE $548.00

1.13 - 7 ga. sides and ends in lieu of 10 ga. (13' body with 36" sides)PRICE $286.00








1.21 - 3/16” AR400 sides & ends in lieu of 10 ga. (13' body with 36" sides)PRICE $2,248.00








1.29 - One piece sloping sides (includes 1 top rail, 2 intermediateside braces, and 1 bottom rub rail)- 10 ga. carbon steel- in lieu of std.10 ga. straight sides (per foot - times foot length of body)

PRICE $78.00

1.30 - One piece sloping sides (includes 1 top rail, 2 intermediateside braces, and 1 bottom rub rail)- 7 ga. carbon steel- in lieu of7 ga. straight sides (per foot - times foot length of body)

PRICE $106.00

1.31 - One piece sloping sides (includes 1 top rail, 1 intermediateside braces, and 1 bottom rub rail)- 3/16" AR400 steel- in lieu of3/16" AR400 straight sides (per foot - times foot length of body)

PRICE $135.00

1.32 - 409 stainless steel rear corner post & apron only, in lieu of std. (all bodies)PRICE $320.00

1.33 - 409 stainless steel front & rear corner post, all side bracing, tailgate bracing, and apron in lieu of standard (13' bodies)

PRICE $1,209.00


PRICE $1,302.00


PRICE $1,395.00


PRICE $1,488.00

1.37 - 4 panel tailgate in lieu of 3 panel (44” & 52 tailgate)PRICE $85.00



1.40 - 3/4" rebar down both sides for walk/tarp rail (all bodies) (per foot - times foot length of body)

PRICE $14.00

1.41 - 1-1/2", grip strut down both sides for walk rail (all bodies) (per foot - times foot length of body)

PRICE $17.00





VENDOR: UNIVERSAL TRUCK EQUIPMENTCONTACT PERSON: DONNIE BJORGEADDRESS: N15921 SCHUBERT RD., GALESVILLE, WI 54630PHONE NO.: 608-539-4600FAX NO.: 608-539-4800

E-MAIL ADDRESS: [email protected]


Box Make and Model Henderson Mark E -ti (XD-SS) 36/44 (13’-16’), 201 Stainless Steel

List truck type box fits Tandem axle only


Width & length of box 13' box length & 96" outside width, 84" inside width

Side panel description 36" high, fully welded, 10 ga. 201S/Sfully boxed-in & fully welded top rails, rub rails are sloped for dirt & debris shedding

Front panel description 60" high, 10 ga. 201S/S construction. Boxed top rail, 12" internal doghouse

Floor description One piece, 3/16" AR400 steel floor-200,000 PSI tensilestrength, 45 degree floor to side knee-brace formed into floor

Corner post description Rear corner post, 7 ga. stainless steel, 5-3/4" x 12", full depth, tied to 8" deep structural channel rear apron. Contoured front corner post and 2" sideboard pockets

Under structure description Two 8" structural steel I-beam long sills with"No splices" (8" x 13.0 lbs./ft.), crossmemberless

Tailgate description 44" high, one piece 10 ga. 201S/S sheet. Extradeep braces. Full perimeter boxing with sloped horizontal brace & top rail. 10 ga. S/S sloped horizontal brace, flush with perimeter boxing(3 panel design) 3/4" latch hooks with 3/8" latch plates. 1-1/4" upper & lower pins. Air trip release kit with double over-center linkage (air over air) (brake chamber type, not cylinder operated)

Hinge Description Flush mount 1/2" flame-cut pivots. Heavy-duty 1" flame cut hinge plates.








PRICE Std.



1.3 - Mark E Asphalt body style (includes sloped tailgate)PRICE $180.00



1.6 - 15-1/2' and 16’ dump body in lieu of 13’PRICE $910.00


PRICE $760.00


PRICE $835.00


PRICE $440.00


PRICE $475.00


PRICE $515.00


PRICE $548.00

1.13 - 7 ga. sides and ends in lieu of 10 ga. (13' body with 36" sides)PRICE $1,294.00








1.21 - One piece sloping sides (includes 1 top rail, 2 intermediateside braces, and 1 bottom rub rail)- 10 ga. 201 stainless steel- in lieu of std.10 ga. straight sides (per foot - times foot length of body)

PRICE $118.00

1.22 - One piece sloping sides (includes 1 top rail, 2 intermediateside braces, and 1 bottom rub rail)- 7 ga. 201 stainless steel- in lieu of std.7 ga. straight sides (per foot - times foot length of body)

PRICE $141.00



1.25 - 3/4" 201 S/S round stock down both sides for tarp rail (per foot - times foot length of body)

PRICE $23.00

1.26 - 1-1/2", 201 S/S grip strut down both sides for walk rail (per foot - times foot length of body)

PRICE $28.00







Box Make and Model Henderson 10' MuniBody 2


Box style Crossmemberless body with live bottom floor

Width & length of box 10ft. box length & 96" outside width

Side panel description 36" high, fully welded, 7ga. grade 50 Hi-tensilesteel, fully boxed-in & fully welded top rails, rub rails are sloped for dirt & debris shedding22 degree floor to side slope.

Front panel description 60" high, 7ga. construction. Boxed top rail and 4" sideboard pockets.

Floor description 1/4" AR400 steel conveyor floor with 28" wide pintlechain - 8 tooth sprockets with 2" drive & idler shafts25:1 planetary gear drive motor- rear mounted15" rear spreader apron. Rear discharge spinner assy.Std. steel spinner disk

Corner post description Rear corner post, 7 ga. steel, 5" x 12-3/4" full depth tied to 12" deep structural steel rear apron with 1/4" tailgate latch reinforcement plates

Under structure description Stainless Steel formed long sills (inner & outer)

Tailgate description One piece 7ga. Grade 50 steel. Extra deep braces. Full perimeter boxing with sloped horizontal brace & top rail. 10 ga. sloped horizontal brace, flush with perimeter boxingScrew adjustable rear feedgate door. 1-1/4" upper & lower pins. Air trip release kitwith double over-center linkage (air over air)(Dual brake chamber type, not cylinder operated)



shock resistant ICC, 3-light cluster is also included. Front & rear mud flaps included. Fold-Uptype mounted front drivers side of the bodyAll electrical wiring connections will be put inheat shrink tubing & will run to a sealed junction box






PRICE Std.



1.3 - Poly Spinner Disk in lieu of std.PRICE $129.00

1.4 - Stainless steel ladder in lieu of mild steelPRICE $290.00

1.5 - Conveyor oiling system- installedPRICE $180.00

1.6 - Front Cross Conveyor (and rear discharge) (9'-12' bodies) SA pin to pin cylinder (installed)PRICE $2,053.00

1.7 - Front Cross Conveyor (and rear discharge) (13'-16' bodies) SA pin to pin cylinderPRICE $3,926.00

1.8 - Front Center and rear discharge (9'-12' bodies)PRICE $380.00

1.9 - Front Center and rear discharge (13'-17' bodies)PRICE $2,200.00

1.10 - External doghouse in lieu of std.PRICE $218.00

1.11 - Rear asphalt patch pan with chute & mount (Front/Rear Discharge)PRICE $460.00

1.12 - Rear asphalt patch pan (Rear Discharge Only)PRICE $180.00

1.13 - Rear Spinner Assy with chute & mount (front/rear discharge)PRICE $1,138.00

1.14 - Combination Rear Spinner Assy & asphalt patch pan with chute & mount(front/rear discharge)

PRICE $1,048.00

1.15 - Front right hand berm chute (M/S)PRICE $160.00

1.16 - Rear berm chute (M/S)PRICE $486.00

1.17 - (1) Mild Steel Toolbox (either side)- Fender mounted (9'-12' body)PRICE $650.00


1.19 - (2) Mild Steel Toolboxes (one on each side)- Fender mounted (9'-12' body)PRICE $1,300.00


1.21 - (1) Stainless Steel Toolbox (either side)- Fender mounted (9'-12' body)PRICE $940.00

1.22 - (1) Stainless Steel Toolbox (either side)- Fender mounted (13'-16' body)PRICE $1,180.00

1.23 - (2) Stainless Steel Toolboxes (one on each side)- Fender mounted (9'-12' body)PRICE $1,880.00


1.25 - (1) 75 Gallon Poly Prewet Tank (either side)- Fender mountedPRICE $582.00

1.26 - (2) 75 Gallon Poly Prewet Tank (one on each side)- Fender mountedPRICE $1,164.00

1.27 - (1) 105 Gallon Poly Prewet Tank (either side)- Fender mountedPRICE $1,030.00








1.35 - (1) 230 Gallon Poly Prewet Tank (either side)- Fender mounted (NA - 10'-12')PRICE $1,615.00

1.36 - (2) 230 Gallon Poly Prewet Tank (one on each side)- Fender mounted PRICE $3,230.00

1.37 - Cradle mount oil tank in lieu of truck frame mountedPRICE $216.00

1.38 - Cradle mount valve body enclosure in lieu of truck frame mountedPRICE $410.00

1.39 - 42" Sides & Ends - 7ga. Grade 50 steel (in lieu of 36" sides & 48" tailgate)PRICE $367.00


1.41 - 3/16” AR400 sides & ends in lieu of 7ga. Grade 50 steelPRICE $2,158.00

1.42 - 36" Unpainted 201 SS Sides & Ends with 1/4" AR400 floor in lieu of grade 50 paintedPRICE $5,683.00






1.48 - Standard Duty Top Grate Screens (3/8" rod x 3/8" rod)- installed PRICE $1,517.00

1.49 - Heavy Duty Top Grate Screens (3/8" rod thru 2" flat)- installed PRICE $2,013.00

1.50 - Rubber belt over pintle chain in lieu of std. pintle chain PRICE $1,365.00

1.51 - Double conveyor cross bars in lieu of std. pintle chain (bars every other link)PRICE $598.00

1.52 - 3/16" AR400 steel conveyor cover platePRICE $732.00

1.53 - Sloped steel side boards- installed and fully welded- Mild SteelPRICE $850.00

1.54 - Sloped steel side boards- installed and fully welded- Stainless SteelPRICE $1,881.00

1.55 - Dual Auger Option in lieu of std. pintle chain…includes top screensPRICE $3,940.00

1.56 - 409 stainless steel rear corner post, all side bracing, tailgate bracing, fenders, and apron in lieu of standard

PRICE $960.00

1.57 - 409 stainless steel rear corner post & apron only, in lieu of std.PRICE $320.00

1.58 - Underbody Pans (Stainless Steel)- installedPRICE $425.00

1.59 - Install cover above rear feed gate doorPRICE $402.00

1.60 - Dual air cylinder operated rear feed gate door with in cab control installed(std. screw jack is still used with air cylinder set-up)

PRICE $1,288.00

1.61 - Rear conveyor control (on/off)- electric switch type- installedPRICE $206.00
























PRICE Std.















PRICE $1,048.00











































PRICE $1,056.00





PRICE $1,288.00

























PRICE Std.















PRICE $1,048.00











































PRICE $1,152.00





PRICE $1,288.00








List truck type box fits Tandem axle, 108" useable CT is recommended

















PRICE Std.















PRICE $1,048.00







































1.53 - Sloped steel side boards- installed and fully welded- Mild SteelPRICE $1,064.00




PRICE $1,248.00





PRICE $1,288.00

























PRICE Std.















PRICE $1,048.00











































PRICE $1,344.00





PRICE $1,288.00

























PRICE Std.















PRICE $1,048.00











































PRICE $1,440.00





PRICE $1,288.00

























PRICE Std.















PRICE $1,048.00






































1.52 - 3/16" AR400 steel conveyor cover platePRICE $1,062.00



1.55 - Dual Auger Option in lieu of std. pintle chain…includes top screensPRICE N/A


PRICE $1,536.00





PRICE $1,288.00

























PRICE Std.















PRICE $1,048.00





































1.51 - Double conveyor cross bars in lieu of std. pintle chain (bars every other link)PRICE $1,020.00

1.52 - 3/16" AR400 steel conveyor cover platePRICE $1,128.00



1.55 - Dual Auger Option in lieu of std. pintle chain…includes top screensPRICE N/A


PRICE $1,632.00





PRICE $1,288.00







Dump Body Options (All Bodies)

1.50 - One set of M/S shovel hooks, fork type (each)PRICE $85.00

1.51 - One set of S/S shovel hooks, fork type (each)PRICE $95.00

1.52 - 22” x 78” cabshield, installed and fully welded, 10 ga. mild steelPRICE $698.00

1.53 - 22” x 78” stationary cabshield, w/rubber flap, installed, 10 ga. m/sPRICE $1,810.00

1.54 - 409 stainless steel cabshield in lieu of mild steelPRICE $180.00

1.55 - 22” x 78” cabshield, installed and fully welded, 10ga. 201S/SPRICE $990.00

1.56 - 22” x 78” stationary cabshield, w/rubber flap, installed, 10ga. 201 S/SPRICE $2,232.00

1.57 - 7 ga. grade 50 steel cabshield in lieu of 10 ga. grade 50 steelPRICE $62.00

1.58 - 7 ga. 201 S/S cabshield in lieu of 10 ga. S/SPRICE $107.00

1.59 - Poly Fenders with rear flaps in lieu of two sets of std. mud flaps (single axle)PRICE $650.00

1.60 - Poly Fenders with rear flaps in lieu of two sets of std. mud flaps (tandem axle)PRICE $1,310.00

1.61 - Tailgate grab handles, one in each corner of lower panel - M/SPRICE $82.00

1.62 - Tailgate grab handles, one in each corner of lower panel - S/SPRICE $98.00

1.63 - Fold-up type ladder in lieu of std. stow-away type ladder PRICE $90.00

1.64 - Stainless Steel fold-up type ladder in lieu of std. stow-away type ladder PRICE $340.00

1.65 - Factory installed tool box across front of dump body, 1/4” grade 50 shell, weather tight sealed key locking doors, one on each side

PRICE $1,136.00

1.66 - Factory installed tool box across front of dump body, 3/16” AR400 shell, weather tight sealed key locking doors, one on each side

PRICE $1,396.00

1.67 - Factory installed tool box across front of dump body, 1/4” S/S shell, weather tight sealed key locking doors, one on each side

PRICE $1,965.00

1.68 - Aluminum tool box frame mounted w/ brackets, 18” x 18” x 24”PRICE $624.00



1.71 - Donovan, electric tarp system with asphalt tarp, all aluminum arms, and tarp housing, standard install, off top of front header

PRICE $2,510.00

1.72 - Donovan front tension bows- installedPRICE $414.00

1.73 - Set of LED Snow Plowing Lights with Heated Lens Truck Lite model 809907in round- 23 Doide- Polycarbonate- 12-24V- std. 94in harness, standard install, off cowling of truck hood with custom made S/S mounting brackets and on/off switch in cab

PRICE $1,385.00

1.74 - One set of Nordic model N520 snow plowing lights with turn signals, light housings are polycarbonate, standard install, off cowling of truck hood with custom made S/S mounting brackets and on/off switch in cab

PRICE $882.00

1.75 - One set of Hella model 996167191/201 snow plowing lights w/turnsignals & standard H4- 60/55 watt bulb, standard install, off cowling of truckhood with custom made S/S mounting brackets and on/off switch in cab

PRICE $832.00

1.76 - Work light, sealed beam type, installed (i.e. sander or wing etc.) (each)PRICE $103.00

1.77 - Work light, LED Type, installed (i.e. sander or wing etc.) (each)PRICE $144.00

1.78 - Two (2) oval rear LED warning lights, recessed rubber mounted in rear corner post, Whelen 5G series, 14 different flash patterns,installed with on/off switch in cab

PRICE $423.00

1.79 - Two (2) oval rear LED warning lights, recessed rubber mounted in rear corner post, Whelen TIR6 series, 14 different flash patterns,installed with on/off switch in cab

PRICE $518.00

1.80 - Whelen Strobe, self contained, 16 jule, class 1, cabshield mounted withprotective guard, wiring will run to on/off switch in cab (each)

PRICE $350.00

1.81 - Whelen model L21HAP - SUPER-LED Beacon, Amber, 6 in. dome type, class 1, polycarbonate base and dome, cabshield mounted with protective guard, wiring will run in conduit to on/off switch in cab (each)

PRICE $384.00

1.82 - Whelen DOT3-401D, Two 2-lamp Micro Freedom LED lightheads, std. 20' TRP cable for each lighthead, 400 series "D" light heads and Stainless Steel housing, 30' rear cables, standard install, mirror moutedfornt strobes and rear light housing welded to outside of rear corner post

PRICE $4,144.00

1.83 - Whelen DOT3-401D (ADD4TIR3), Two 2-lamp Micro Freedom LED lightheads, std. 20' TRP cable for each lighthead, 400 series "D" light heads & Stainless Steel housing w/ TIR3 side light, standard install, mirrormounted front strobes and rear light housing welded to outside of rear corner post

PRICE $4,334.00

1.84 - Whelen DOT3-701D, Two 2-lamp Micro Freedom LED lightheads, std. 20' TRP cable for each lighthead, 700 series "D" light heads and Stainless Steel housing, 30' rear cables, standard install, mirror moutedfornt strobes and rear light housing welded to outside of rear corner post

PRICE $3,969.00

1.85 - Whelen DOT3-701D (ADD7TIR3), Two 2-lamp Micro Freedom LED lightheads, std. 20' TRP cable for each lighthead, 700 series "D" light heads & Stainless Steel housing w/ TIR3 side light, standard install, mirrormounted front strobes and rear light housing welded to outside of rear corner post

PRICE $4,159.00

1.86 - Adjustable aluminum light bar, cab mounted, in lieu of mirror mount brackets, (truck cab needs to have a drip rail/rain gutter)

PRICE $206.00

1.87 - Adjustable aluminum light bar, cab mounted, in lieu of mirror mount brkt.(truck has "no" drip rail/rain gutter - holes will need to be drilled in truck cab)

PRICE $390.00

1.88 - Weld rear DOT3 lighthead housings in rear corner post in lieu of welding to outside of rear corner post

PRICE $84.00

1.89 - Federal Signal model 454205-25 Economy HighLighter LED warning lightClass 1, 15" mini-lightbar with Amber LED's and Clear Lens- cabshield mounted withprotective guard, wiring will run to on/off switch in cab (each)

PRICE $515.00

1.90 - Federal Signal model 454201-25 HighLighter LED warning light, Class 1,15" mini-lightbar with Amber LED's and Clear Lens- cabshield mounted withprotective guard, wiring will run to on/off switch in cab (each)

PRICE $622.00

1.91 - Electronic Back-up Alarm- 97 decibels- 12 volt systems- installedPRICE $106.00

1.92 - Switch panel box with 5 or 6 lighted switches and individualbreakers for each switch, installed with one piece full wiring harnessfrom switch box to light, price is in lieu of dash mounted switches

PRICE $376.00

1.93 - Quick detachable mud flaps in lieu of standard (per set)PRICE $52.00

1.94 - Roll-Rite, electric tarp system with asphalt tarp, all aluminum arms, tarphousing, and TarpMaster Motor - standard install, off top of front header

PRICE $2,876.00

1.95 - Roll-Rite Super Duty motor in lieu of TarpMaster MotorPRICE $191.00

1.96 - Roll-Rite front tension bows- installedPRICE $299.00

1.97 - Aero, electric tarp system with asphalt tarp, all aluminum arms, tarphousing, and Power Plus Motor - standard install, off top of front header

PRICE $2,670.00

1.98 - Aero front tension bows- installedPRICE $289.00

1.99 - Henderson (1) 60 gallon elliptical pre-wet tank - installedPRICE $724.00

1.100 - Henderson (2) 60 gallon elliptical pre-wet tanks - installedPRICE $1,448.00

1.101 - Henderson (1) 100 gallon elliptical pre-wet tank - installedPRICE $898.00

1.102 - Henderson (2) 100 gallon elliptical pre-wet tanks - installedPRICE $1,796.00

1.103 - Henderson Stainless Steel pre-wet tank receiver tubes (elliptical bodies) (Ea.)PRICE $34.00

1.104 - Hella HID auxillary lights (90673B)- lightbar or stationary cabshield mountedPRICE $990.00

1.105 - Amber wing warning light Whelen TIR3 # WPLOW1A- "In Use" - installedPRICE $305.00

1.106 - Amber wing warning light Whelen TIR3 # WPLOW2A- "Stowed" - installedPRICE $305.00

1.107 - Hoist stabilizer (used with Mailhot tele hoist)- installedPRICE $3,980.00

1.108 - Stainless Steel rear chute tube brackets & S/S storage pins ilo M/S - installed PRICE $352.00

1.109 - License plate light- std. installPRICE $266.00

1.110 - Body-Up Switch- installedPRICE $110.00

1.111 - Rubber/Steel mounting pads- installed (all MKE bodies 13'-16')PRICE $1,085.00

1.112 - 20 ton pintle hitch installed w/ 3/4” steel plate bracing, D-rings, plugPRICE $840.00

1.113 - 30 ton pintle hitch installed w/ 3/4” steel plate bracing, D-rings, plugPRICE $918.00

1.114 - 45 ton pintle hitch installed w/ 1” steel plate bracing, D-rings, plugPRICE $1,062.00

1.115 - 50 ton pintle hitch installed w/ 1” steel plate bracing, D-rings, plugPRICE $1,258.00

1.116 - Custom chipper hitch- installed by itself (with no other hitch)PRICE $490.00

1.117 - Custom chipper hitch- installed with additional hitch (must add additional hitch)PRICE $622.00

1.118 - Whelen SnowAway (H400SD) 400 series heated rear lens with auto on/off & switch in the cabPRICE $1,768.00

1.119 - Stainless Steel fixed length cabshield mounted lightbar in lieu of mirror mount brktsPRICE $210.00

1.120 - Whelen DOT3-410D, Two Stainless Steel 2-lamp Micro 400 LED lightheads, std. 20' TRP cable for each lighthead, 400 series "D" light heads and Stainless Steel housing, 30' rear cables, standard install, mirror moutedfornt strobes and rear light housing welded to outside of rear corner post

PRICE $4,240.001.121 - Whelen DOT3-410D, (ADD4TIR3), Two Stainless Steel 2-lamp Micro 400 LED lightheads, std. 20' TRP cable for each lighthead, 400 series "D" light heads and Stainless Steel housing, 30' rear cables, standard install, mirror moutedfornt strobes and rear light housing welded to outside of rear corner post

PRICE $4,430.00

1.122 - Donvan Spring Trap (spring loaded tarp hold down)- installedPRICE $394.00

1.123 - S/S unpainted stow-away ladder in lieu of std. M/S painted stow-away ladderPRICE $216.00

1.124 - Greaseable upper tailgate pins (all bodies)PRICE $45.00

1.125 - Amber wing warning light Whelen TIR3 on UTE SS bracket- "In Use" - installedPRICE $248.00

1.126 - Fully welded I-beam longsills (MKE Bodies) in lieu of std. skip weldedPRICE $150.00

1.127 - (1) extra obround light hole in each rear corner postPRICE $25.00

1.128 - (2) extra obround light holes in each rear corner postPRICE $50.00

1.129 - Larger 8.0 cu. in. conveyor drive motors in lieu of std.PRICE $210.00

1.130 - Oval LED Back-Up Lights - installedPRICE $190.00

1.131 - 3-oval hole Stainless Steel light boxes - installed to outside rear corner posts with 1/2" gapPRICE $350.00

1.132 - (4) single oval hole Stainless Steel light boxes - installed on cabshield with 4-LED S/T/TPRICE $748.00

1.133 - Install one set of chain hangers (in requested location) (per set)PRICE $150.00

1.134 - Stainless Steel Tubing front to rear on MuniBody'sPRICE $353.00

1.135 - Install inside stepPRICE $40.00

1.136 - Relocate factory truck tow hooksPRICE $125.00

1.137 - Weld stainless steel angle to tailgate for customer to install license platePRICE $100.00

1.138 - Install custom round storage basket to truck framePRICE $345.00

1.139 - Install reflective 3M tape to sides & ends of body…get location details (per feet of tape needed)PRICE $2.00





Documents

PRICE SCHEDULE 1.0 VENDOR TO PROVIDE Box FOLLOWING …