PRODUCT CATALOGCATALOG...Company has the production capacity of 1000 tons of finished products a day with the product portfolio offering solutions for all kinds of finishing works

1

PRODUCT CATALOG

1

PRODUCT CATALOG

2

Introduction 3

Primers 4

Levelling compounds 8

Gypsum compounds 11

Paints for interior surfaces 12

Decorative treatment 14

Paints and coats for exterior surfaces 22

Wood paints and coats 24

Supplementary products 25

Wood and parquet adhesives 26

Ceramics programme 28

Waterproofing coats 30

Machine applied mortars 32

Styrofoam 34

Decorative facade renders 36

Adhesives for thermal insulation systems 40

MAXITHERM Thermal insulation systems 41

CONTENTS

3

Maxima is a family company established in 1990 as a paint trading company. Having seen that the offer of high quality interior paints at the market was poor, the family decided to start their own production in 1994. The first product on its road of development was Maxipol, the product which made this company easy to recognize.

The beginnings were very modest. The daily production capacity amounted to 5 tons. Today Maxima Company has the production capacity of 1000 tons of finished products a day with the product portfolio offering solutions for all kinds of finishing works in civil engineering.

The passion for perfecting the existing products and developing new technologies, its commitment to customers and their requirements, its belief that the top quality is the only imperative when considering design of new formulas, production and distribution of products, have brought Maxima Company to the rank of most successful companies from this region in the field of manufacturing products for finishing works in civil engineering.

The most valuable item which distinguishes Maxima are its loyal customers who have recognized the company’s efforts to provide the best quality and price ratio and have rewarded the company with their trust in this brand. Thank you for that!

4

PRIMERS

MAXIKRIL® ConcentrateProperties and use: MAXIKRIL Concentrate is an acrylic primer used for impregnation of various substrates (brick, concrete, fibrous-cement substrates, etc.) before dispersion paints and decorative facade renders are applied. MAXIKRIL Concentrate is easy to apply, dries quickly and provides good quality substrate impregnation. Coated surfaces are uniform, evenly painted, less absorbent, have improved adhesion of finishing products and reduce their consumption. Dry coating film is colourless. Do not use MAXIKRIL Concentrate if the silicate-or silicone-based products are used for finishing operations.

Manner of application: Surface must be dry, with good load-bearing capacity and free of dust, grease, crumbly areas and old coats. Prior to application, dilute MAXIKRIL Concentrate with water in 1:9 ratio. Apply one coat using a roller, brush or tank sprayer. Drying time in optimum conditions is at least 6 hours. After application, immediately rinse the tools with water.

Application temperature: Optimum applica-tion temperature ranges from +10°C to +30°C. it must not be used below +5°C as well as in bright sunshine, wind, fog or rain.

Consumption: From 20-30ml/m², depending on the roughness and absorption capacity of substrate.

Shelf life and storage: 18 months from the date of production stated on the packaging. Keep in the original, properly sealed and undamaged packaging at the temperatures from +5°C to +25°C, protected from direct sunlight.

MAXIKRIL® HidrosolProperties and use: MAXIKRIL Hidrosol is a special acrylic deep penetration coat used for impregnation of smooth mineral and concrete exterior and interior surfaces as well as gypsum-cardboard panels. It is particularly recommended for less solid surfaces prior to application of paint and decorative renders. It penetrates deep into the substrate and makes it more even, stronger, increases its water resistance, improves adhesion of finishing products and reduces their consumption. Do not use MAXIKRIL Hidrosol if silicate or silicone-based products are used for finishing operations.

Manner of application: Surface must be dry, with good load-bearing capacity and free of dust, grease, crumbly areas and old coats. Prior to application, dilute MAXIKRIL Hidrosol with water in 1:5 ratio. Apply one coat using a roller, brush, or tank sprayer. Drying time in optimum conditions is at least 6 hours. After application, immediately rinse the tools with water.




MAXIKRIL®

Properties and use: MAXIKRIL is an acrylic pri-mer used for impregnation of various substrates (brick, concrete, fibrous-cement substrates, etc.) before dispersion paints and decorative facade renders are applied. MAXIKRIL is easy to apply, dries quickly and provides good quality substra-te impregnation. Coated surfaces are uniform, evenly painted, less absorbent, have improved adhesion of finishing materials and reduce their consumption. Dry coating film is colourless. Do not use MAXIKRIL if the silicate or silicone-based products are used for finishing operations.

Manner of application: Surface must be dry, with good load-bearing capacity and free of dust, grease, crumbly areas and old coats. Prior to application, dilute MAXIKRIL with water in 1:3 ratio. Apply one coat using a roller, brush or tank sprayer. Drying time in optimum conditions is at least 6 hours. After application, immediately rinse the tools with water.

Application temperature: Optimum applica-tion temperature ranges from +10°C to +30°C. It must not be used below +5°C as well as in bright sunshine, wind, fog or rain.



liter

1|5|18liter

1|5|18liter

1|5|18

5

MAXIKRIL® ContactProperties and use: MAXIKRIL Contact is a coarse acrylic foundation coat micro-reinforced by synthetic fibres and filled with quartz particles. It is used for grouting substrate prior to application of machine applied mortars as a bonding bridge. MAXIKRIL Contact evens out the absorption and increases substrate roughness which facilitates better adhesion of products applied afterwards. It is applied to smooth concrete surfaces prior to application of gypsum and cement-lime MAXIMAL machine applied mortars.

Manner of application: Surface must be dry, with good load-bearing capacity and free of dust, grease, crumbly areas and old coats. Prior to application, only stir MAXIKRIL Contact and it is ready to use. Apply one coat using a roller, brush or tank sprayer when it may be diluted with water up to 10% if necessary. Drying time in optimum conditions is at least 12 hours. After application, immediately rinse the tools with water.

Application temperature: Optimum applica-tion temperature ranges from +10°C to +30°C. It must not be used below +5°C as well as in bright sunshine, wind, fog or rain. Protect the newly coated surfaces from weather impact for at least 12 hours.

Consumption: Approximately 160-200g/m², depending on the roughness and absorption capacity of substrate.


MAXIKRIL® CeramicProperties and use: MAXIKRIL Ceramic is an acrylic primer used for impregnation of both absorbent and non-absorbent problem surfaces (glazed tiles, concrete, stone, terrazzo, gypsum panels, aerated concrete elements and gypsum, lime and cement machine appli-ed mortars) prior to application of adhesives and levelling compounds. MAXIKRIL Ceramic is easy to apply, dries quickly and provides high-quality substrate impregnation, provides very high water repellence and bonding. Coated surfaces are uniform, do not absorb and im-prove adhesion of adhesive agents. Do not use MAXIKRIL Ceramic as a primer for paints and decorative renders.

Manner of application: Surface must be dry, with good load-bearing capacity and free of dust, grease, crumbly areas and old coats. Prior to application, dilute MAXIKRIL Ceramic with water in 1:3 ratio and for very absorbent substrates use the undiluted product. Apply one coat using a brush, roller or tank sprayer. Drying time in optimum conditions is at least 8 hours. After application, immediately rinse the tools with water.


Consumption: From 30-150ml/m², depending on the dilution ratio, roughness and absorption capacity of substrate.


MAXIKRIL® BlockProperties and use: MAXIKRIL Block is an acrylic primer for blocking, i.e. isolating water-soluble stains, such as stains from cigarette smoke, soot and stains caused by damp or flooding. MAXIKRIL Block is applied on dry and clean, plastered, skimmed interior surfaces and gypsum-cardboard panels. MAXIKRIL Block is not efficient if the stained surfaces have been previously treated with similar agents which are not water-borne.

Manner of application: Surface must be solid, dry, with good load-bearing capacity and free of dust, grease, crumbly areas and old coats. Prior to use, dilute MAXIKRIL Block with water in 1:3 ratio. Apply one coat using a brush, roller or tank sprayer. Drying time in optimum conditions is at least 24 hours. Surfaces treated with MAXIKRIL Block after their drying must be coated with MAXIDIS or ULTRADIS dispersion paints in compliance with the producer’s instructions. After application, immediately rinse the tools with water.

Application temperature: Optimum application temperature ranges from +10°C to +30°C. it must not be used below +5°C.



liter

1|5kg

5|25kg

1|5

6

PRIMERS

MAXISIL® SNProperties and use: MAXISIL SN is a silicone primer used for impregnation of cement and cement-lime facade surfaces prior to application of silicone paints. MAXISIL SN is easy to apply and provides high-quality substrate impregnati-on. Coated surfaces are uniform, evenly painted, less absorbent, have improved adhesion of finis-hing products and reduce their consumption.

Manner of application: Surface must be dry, with good load-bearing capacity and free of dust, grease, crumbly areas and old coats. Prior to application, dilute MAXISIL SN with water in 1:1 ratio. Apply one coat using a roller, brush or tank sprayer. Drying time in optimum conditions is at least 12 hours. After application, immediately rinse the tools with water.

Application temperature: Optimum applica-tion temperature ranges from +10°C to +30°C. it must not be used below +5°C as well as in bright sunshine, wind, fog or rain. Protect the newly coated surfaces from weather impact for at least 12 hours.



MAXISIL® STProperties and use: MAXISIL ST is a silicate primer used for impregnation of cement and cement-lime facade surfaces prior to application of silicate paints. MAXISIL ST is easy to apply and provides high-quality substrate impregnation. Coated surfaces are uniform, evenly painted, less absorbent, have improved adhesion of finishing products and reduce their consumption.

Manner of application: Surface must be dry, with good load-bearing capacity and free of dust, grease, crumbly areas and old coats. Prior to application, dilute MAXISIL ST with water in 1:1 ratio. Apply one coat using a roller, brush or tank sprayer. Drying time in optimum conditions is at least 24 hours. After application, immediately rinse the tools with water.

Application temperature: Optimum applica-tion temperature ranges from +10°C to +25°C. it must not be used below +8°C as well as in bright sunshine, wind, fog or rain. Protect the newly coated surfaces from weather impact for at least 24 hours.


Shelf life and storage: 9 months from the date of production stated on the packaging. Keep in the original, properly sealed and undamaged packaging at the temperatures from +5°C to +25°C, protected from direct sunlight. Keep out of children’s reach.

liter

1|5liter

1|5

7

ROLOGRUND® STProperties and use: ROLOGRUND ST is a coarse silicate foundation coat, micro-reinforced by synthetic fibres and filled with quartz sand. It is used for grouting mineral surfaces prior to appli-cation of silicate decorative render ROLOSIL ST. ROLOGRUND ST provides a rougher substrate, i.e. increases its roughness, which facilitates better adhesion of finishing products. It is available in white shade and can be tinted in MAXIMIX system.

Manner of application: Surface must be dry, with good load-bearing capacity and free of dust, grease, crumbly areas and old coats. Tint ROLOGRUND ST in the shade approximate to the shade of render finish. Apply one coat of ROLOGRUND ST with a roller or a brush when it may be diluted with water up to 10%. Drying time in optimum conditions is at least 24 hours. After application, immediately rinse the tools with water.


Consumption: From 140-160g/m², depending on the roughness and absorption capacity of substrate.


ROLOGRUND® SNProperties and use: ROLOGRUND SN is a coarse silicone foundation coat, micro-reinforced by synthetic fibres and filled with quartz sand. It is used for grouting mineral surfaces prior to application of silicone decorative render ROLOSIL SN. ROLOGRUND SN provides a rougher substrate, i.e. increases its roughness which facilitates better adhesion of finishing products. It is available in white shade and can be tinted in MAXIMIX system.

Manner of application: Surface must be dry, with good load-bearing capacity and free of dust, grease, crumbly areas and old coats. Tint ROLOGRUND SN in the shade approximate to the shade of render finish. Apply one coat of ROLOGRUND SN with a roller or a brush when it may be diluted with water up to 10% maximum. Drying time in optimum conditions is at least 12 hours. After application, immediately rinse the tools with water.




ROLOGRUND®

Properties and use: ROLOGRUND is a coarse acrylic foundation coat, micro-reinforced by synthetic fibres and filled with quartz sand. It is used for grouting substrates (mineral and concrete exterior and interior surfaces, gypsum-cardboard panels) prior to application of decorative renders which are not silicate based. ROLOGRUND increases substrate roughness which facilitates better adhesion of finishing products. It is available in white shade and can be tinted in MAXIMIX system.

Manner of application: Surface must be dry, with good load-bearing capacity and free of dust, grease, crumbly areas and old coats. Tint ROLOGRUND in the shade approximate to the shade of render finish. Apply one coat of ROLOGRUND with a roller or a brush when it may be diluted with water up to 10%. Drying time in optimum conditions is at least 12 hours. After application, immediately rinse the tools with water.




kg

5|18|25kg

5|18|25kg

5|18|25

8

GLETOLIN® GProperties and use: GLETOLIN G is a paste-like acrylic-based compound used for fine levelling of interior, firmly plastered wall surfaces as well as gypsum-cardboard panels. GLETOLIN G is distinguished by its exquisite whiteness, ease of application and workability. Levelled, fully dry surfaces can be painted with all kinds of dispersion paints.

Manner of application: GLETOLIN G is ready to use. Wall surfaces must have good load-bearing capacity and be free of dust, grease and other impurities. Before GLETOLIN G is applied, surfaces must be grouted with an adequate MAXIKRIL base depending on the surface condition. Apply GLETOLIN G to walls using a steel trowel or stainless paint broad knife. It can be machine applied when it needs to be diluted with a small amount of water. After drying, each coat must be well sanded with sand paper. Drying time before applying the next coat, i.e. sanding, in optimum conditions is at least 12 hours. Maximum recommended total coat thickness is up to 3mm. After application, immediately rinse the tools with water.

Application temperature: Optimum application temperature ranges from +10°C do +30°C. It must not be used below +5°C.

Consumption: 1.5-2.0kg/m² depending on the substrate roughness.

Shelf life and storage: 12 months from the date of production stated on the packaging. Keep in an original, properly sealed and undamaged packaging at the temperatures from +5°C to +25°C, protected from direct sunlight.

kg

1|5|25

9

LEVELLING COMPOUNDS

GLETOLIN®

Properties and use: GLETOLIN is a powdery compound used for levelling interior, firmly plastered wall surfaces as well as gypsum-cardboard panels. GLETOLIN is distinguished by its exquisite whiteness, ease of application and good workability. Levelled, fully dry surfaces can be painted with all kinds of dispersion paints.

Manner of application: Add a 25kg bag of GLE-TOLIN to 10l of water and mix until a homogeno-us and lump-free compound is achieved. Leave it for 15 minutes and then mix thoroughly again. Compound made in this manner is ready for application and must be used within 24 hours. Wall surfaces must have good load-bearing capacity and be free of dust, grease and other impurities. Before GLETOLIN S is applied, surfaces must be grouted with an adequate MAXIKRIL base depending on the surface condition. Apply the prepared compound using a steel trowel or stainless paint broad knife. After drying, each coat must be well sanded. Drying time before applying the next coat, i.e. sanding, in optimum conditions is at least 12 hours. Maximum re-commended total coat thickness is up to 5mm. After application, immediately rinse the tools with water.



Shelf life and storage: 12 months from the date of production stated on the packaging. Keep in a properly sealed and undamaged packaging in dry and well aerated premises.

GLETOLIN® BioProperties and use: GLETOLIN Bio is a powdery compound for levelling interior, firmly plastered wall surfaces as well as gypsum-cardboard panels. GLETOLIN Bio is distinguished by ease of application and good workability. Levelled, fully dry surfaces can be painted with all kinds of dispersion paints.

Manner of application: Add a 25kg bag of GLETOLIN Bio to 10l of water and mix until a homogenous, lump-free compound is achieved. Leave it for 15 minutes and then thoroughly mix again. Compound made in this manner is ready for application and must be used within 24 hours. Wall surfaces must have good load-bearing capacity and be free of dust, grease and other impurities. Before GLETOLIN Bio is applied, surfaces must be grouted with an adequate MAXIKRIL base depending on the surface condition. Apply the prepared compound to the wall surfaces using a steel trowel or stainless steel paint broad knife. After drying, each coat must be well sanded with sand paper. Drying time before applying the next coat, i.e. sanding, in optimum conditions is at least 12 hours. Maximum recommended total coat thickness is up to 5mm. After application, immediately rinse the tools with water.




GLETOLIN® MProperties and use: GLETOLIN M is a powdery compound used for machine levelling of interior, firmly plastered walls and gypsum-cardboard panels. GLETOLIN M is distinguished by its exquisite whiteness, ease of application and good workability. Levelled, fully dry surfaces can be painted with all kinds of dispersion paints.

Manner of application: Feed the machine with a required quantity of GLETOLIN M, press start and set the required water quantity and mixing speed. The mixed compound at the outlet nozzle of sprayer must have an adequate density. Wall surfaces must have good load-bearing capacity and be free of dust, grease and other impurities. Before GLETOLIN M is applied, surfaces must be grouted with an adequate MAXIKRIL base depending on the surface condi-tion. Apply in two coats. After drying, each coat must be well sanded with sand paper. Drying time before applying the next coat, i.e. sanding, in optimum conditions is at least 12 hours. Maximum recommended total coat thickness is up to 5mm. After application, immediately rinse the machine and tools with water.




kg

25kg

25kg

5|25

10

kg

5|25kg

25kg

25

LEVELLING COMPOUNDS

SAMOLIV®

Properties and use: SAMOLIV is a cement self-levelling compound used for levelling interior concrete floors. It is suitable for application in premises with underfloor heating and prior to laying floor lining (PVC flooring, laminate, parquet, ceramic tiles...). After hardening, a fine, smooth surface is obtained. It is applied in a thick coat with maximum thickness up to 8mm. If a thicker coat is required, repeat the applica-tion, but only after the previous coat is fully dry. SAMOLIV is not used as a walk-on topcoat.

Manner of application: Add a 25kg bag of SAMOLIV to 6l of water and mix until a homoge-nous, lump-free compound is achieved. Leave it for 3-5 minutes and then mix thoroughly again. Compound prepared in such a manner is ready for application and must be used within 25 minutes. Surface must be solid and clean, free of grease and other impurities which could prevent good adhesion. Moisture content of the surface where the compound is to be applied must not exceed 3%. In case the surface has larger holes, fill them with KERAMOL a day before SAMOLIV application. Prior to SAMOLIV application, grout the surfaces with an adequate MAXIKRIL base depending on the surface condi-tion. Apply the compound either by machine or pour the compound manually. After application, use a metal trowel or a rubber or metal spreader to evenly spread the compound. The floor can be used for walking after 24 hours, i.e. 48 hours depending on the applied coat thickness. Further processing is possible after 4-5 days.

Application temperature: Optimum applicati-on temperature ranges from +10°C do +30°C. It must not be used below +5°C.

Consumption: ≈1.4kg/m²/mm.


GLETOLIN® DSProperties and use: GLETOLIN DS is a powdery compound based on white cement, fillers and special additives and is used for levelling extre-mely uneven exterior and interior firmly plaste-red walls, thus it can be applied in a thick coat. GLETOLIN DS is distinguished by its exquisite whiteness, ease of application and workability. Levelled, fully dry surfaces can be painted with all kinds of dispersion paints in interior, i.e. with façade paints for façade surfaces.

Manner of application: Add a 25kg bag of GLETOLIN DS to 7l of water and mix until a homogenous, lump-free compound is achieved. Leave it for 15 minutes and then thoroughly mix again. Compound made in this manner is ready for application and must be used within 2 hours. Wall surfaces must have good load-bearing capacity and be free of dust, grease and other impurities. Before GLETOLIN DS is applied, surfaces must be grouted with an adequate MAXIKRIL base depending on the surface condition. Compound is usually applied in one coat, manually using a stainless steel trowel. Drying time, before the next coat is applied, is 2-5 days depending on the applied coat thickness. Maximum recommended total coat thickness is up to 10mm. Surfaces levelled in such a manner can be painted after 14 days. After application, immediately rinse the tools with water.

Application temperature: Optimum applicati-on temperature ranges from +10°C do +30°C. It must not be used below +5°C as well as in bright sunshine, wind, fog and rain. Protect the newly coated surfaces, in optimum conditions, from the weather impact for at least 24 hours.

Consumption: ≈1.5kg/m²/mm depending on the substrate roughness.


GLETOLIN® SProperties and use: GLETOLIN S is a powdery compound based on white cement, fillers and special additives used for levelling concrete and firmly plastered exterior and interior wall surfaces. GLETOLIN S is distinguished by its exquisite whiteness, ease of application and good workability. Levelled, fully dry surfaces can be painted with all kinds of dispersion paints in interiors, i.e. with facade paints for facade surfaces.

Manner of application: Add a 25kg bag of GLETOLIN S to 9l of water and mix until a homogenous and lump-free compound is achieved. Leave it for 15 minutes and then mix thoroughly again. Compound made in this manner is ready for application and must be used within 2 hours. Wall surfaces must have good load-bearing capacity and be free of dust, grease and other impurities. Before GLETOLIN S is applied, surfaces must be grouted with an adequate MAXIKRIL base depending on the surface condition. Compound is usually applied in two coats, manually using a stainless steel trowel. Drying time before applying the next coat, i.e. sanding, in optimum conditions is at least 24 hours. Maximum recommended total coat thickness must not exceed 3mm. Surfaces levelled in such a manner can be painted after 14 days. After application, immediately rinse the tools with water.


Consumption: 1.0-2.0kg/m², depending on the substrate roughness.


11

GYPSUM COMPOUNDS

MAXIFIL® FixProperties and use: MAXIFIL Fix is a powdery gypsum-based compound with addition of fillers and additives. It is used for fixing gypsum-cardboard panels. It is easy to apply, abundant, with good adherence, strength, longer open time of application.

Manner of application: Add 25kg of MAXIFIL Fix into ≈8-9l of water and thoroughly mix with manual mixer to achieve a homogenous, lump-free mixture. Open time is about 40 minutes. Wall surfaces must have good load-bearing capacity and be cleaned from dust, grease and other impurities. Before applying adhesive compound, impregnate the surfaces with an appropriate primer. Apply MAXIKRIL Contact to concrete and smooth surfaces, MAXIKRIL Hi-drosol base to crumbly surfaces and MAXIKRIL Concrete to highly absorbent surfaces. Apply MAXIFIL Fix onto the edges and the middle area of gypsum-cardboard panel in the form of a strip when the surface is even. If the surface where gypsum-cardboard panel is to be fixed is uneven and a thicker coat of adhesive is requ-ired, apply dabs of MAXIFIL Fix with a spacing of approximately 25cm. In case of very uneven surfaces, cut the gypsum-cardboard panel in 100mm wide strips of and fix them vertically onto the wall. If the surface does not have good load-bearing capacity, fix it additionally with rawl plugs. Apply thin coat of MAXIFIL Fix to the positioned boards after the adhesive has harde-ned using a notched trowel. After application, immediately rinse the tools with water.


Consumption: ≈2.5-5.0kg/m² depending on the type of fixing and surface where gypsum-cardboard panel is to be fixed.

Shelf life and storage: 12 months from the date of production stated on the packaging. Keep in the sealed and undamaged packaging, in dry and well aerated premises.

MAXIFIL® JFProperties and use: MAXIFIL Joint Filler is a powdery gypsum-based compound with addi-tion of fillers and additives. It is used for filling joints of gypsum-cardboard panels with HRAK half-rounded and AK tapered edges using strips (bandage, glass, paper). It is distinguished by high abundance, good adherence, strength, lon-ger open time of application. It can be used for filling damaged areas and screws for gypsum-cardboard panel fixing as well as for their fixing if the thin-coat adhesive technique is used.

Manner of application: Add 5kg of MAXIFIL Joint Filler to ≈2.3l of water, mix well using a broad knife until a homogenous, lump-free mixture is achieved. Open time is about 40 minutes. When treating joints of gypsum-cardboard panels, clean the joints from dust and other impurities. Fill the joints with the filler, then apply some of the strips (bandage, glass or paper depending on the joint type) and push it slightly into the substance. Apply the second coat over the fully dry previous coat. If bonding is to be performed, clean the surfaces from dust and crumbly particles and grout them with an appropriate MAXIKRIL base depending on the surface condition. Apply the substance with a notched trowel along the panel edges and mid area in the form of a strip. Do not use MAXIFIL Joint Filler when the air humidity in premises is higher and if water-repellent gypsum-cardboard panels are used. For water-repellent gypsum-cardboard panels use MAXIFIL JFH. After the application, immediately rinse the tools with water. Treat the surfaces further after 2-3 days depending on the temperature and relative humidity.


Consumption: ≈0.2-0.7kg/m² for joint filling, depending on the location and type of joints. ≈1kg/m² for bonding gypsum-cardboard panels.


kg

25kg

5|25

12

MAXIPOL®

Properties and use: MAXIPOL is an ecological paint for interior wall surfaces. It is distinguished by exquisite whiteness, high covering power, water vapour permeability and resistance to dry scrubbing. It is suitable for painting all kinds of dry and solid substrates: fine rendered vertical and ceiling surfaces, concrete, fibre-cement sur-faces and gypsum-cardboard panels. MAXIPOL can be tinted by MAXI Color or MAXIFAS Color as well as in MAXIMIX system.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with some of GLETOLIN levelling compounds used for interior walls skimming. Prior to painting, impregnate the walls with an appropriate MAXIKRIL base coat depending on the surface condition. Apply two coats of MAXIPOL with a brush, roller or tank sprayer. For the first coat the paint may be diluted with water up to 40% while for the second coat it may be diluted up to 25%. Apply the second coat after 6 hours, i.e. when the first coat is fully dry. After application, immediately rinse the tools with water.


Consumption: 125-185ml/m² for two-coat application, depending on the roughness and absorption capacity of substrate.

Shelf life and storage: 18 months from the date of production stated on the packaging. Keep in the original, properly sealed and undamaged packaging at the temperatures from +5°C do +25°C, protected from the direct sunlight.

MAXIDIS®

Properties and use: MAXIDIS is a high-quality water-washable dispersion paint based on acrylic binders. It provides good adherence to substrates, excellent covering power, distinctive whiteness, water vapour permeability and resistance to wet scrubbing. It is used for pro-tection and decoration of interior walls made of concrete, extended render, aerated concrete, asbestos-cement, chipboard. MAXIDIS can be tinted with MAXI Color or MAXIFAS Color as well as in MAXIMIX system.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with some of GLETOLIN levelling compounds used for interior walls skimming. Prior to painting, impregnate the walls with an appropriate MAXIKRIL base coat depending on the surface condition. Apply two coats of MAXIDIS with a brush, roller or tank sprayer. The paint may be diluted with water from 15% up to 25% maximum. Apply the second coat after 6 hours, i.e. when the first coat is fully dry. After application, immediately rinse the tools with water.


Consumption: 125-185ml/m² for two-coat application, depending on the roughness and absorption capacity of the substrate.


MAXIDIS® FProperties and use: MAXIDIS F is interior, was-hable, dispersion paint based on acrylic binders, extremely resistant to fungus and mould. It provides good adherence to substrate, excellent coverage, distinctive whiteness, water vapour permeability and resistance to wet scrubbing. MAXIDIS F coating efficiently fights mould growth in damp premises such as basements, kitchens, bathrooms, etc. MAXIDIS F can be tinted with MAXI Color or MAXIFAS Color as well as in MAXIMIX system.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose and crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. In case the surface is infected by fungus or algae, treat it first with MAXICID agent against wall algae and fungus. Level the uneven surfaces with an appropriate GLETOLIN levelling compound used for interior walls skimming. Prior to painting, impregnate the walls with an appropriate MAXIKRIL base coat depending on the surface condition. Apply two coats of MAXIDIS F with a brush, roller or tank sprayer. The paint may be diluted with water from 10% up to 15%. In order to preserve its fungicide properties, the percen-tage of total dilution of MAXIDIS F dispersion with water or tinting agents must not exceed 15%. Apply the second coat after 6 hours, i.e. when the first coat is fully dry. After application, immediately rinse the tools with water.




liter

1|3|5|10|15liter

0.65|3|5|15liter

0.65|3|5|15

13

MAXILATEX

® SatenCharacteristics and purpose: MAXILATEX is a harmless coating based on a vinyl binder with satin sheen. It is characterized by an exceptional resistance to washing with water, universal de- tergents and disinfectants, as well as by an exce-llent resistance to abrasion. It is recommended for the protection and decoration of interior ceiling and wall surfaces, which are frequently washed, such as kitchens and public spaces, including: hospitals, kindergartens, schools etc., and premises, where there are large numbers of people, such as hallways, restaurants etc. It is designed for the protection and decoration of interior mineral wall surfaces, as well as of gypsum board, glass-fiber relief wallpaper etc. Available in white color and as a base for tinting with MAXIMIX system.

Work method: The surface must be: dry, load-bearing capable, clean and free of loose materials, dust, water-soluble salts, grease and other contaminants. Old paint that is not well-adhered and paint that is not resistant to wet washing should be mechanically removed. Uneven surfaces must be smoothed with skim plaster GLETOLIN for inner walls. Before painting, the walls should be impregnated a suitable MAXIKRIL primer, depending on surface conditions. MAXILATEX is applied by brush, short-fiber roller or sprayer, in two coats. The paint can be diluted with water up to 5%. The second coat should be applied after 6 hours, or when the previous coat is completely dry. After use, wash the tools immediately with water.

Working temperature: The optimum working temperature is between +10°C and +30°C. It should not be used below +5°C.

Consumption: 8-9m²/l in two coats, depending on the roughness and porosity of the substrate, as well as on the technique and method of application.

Shelf life and storage: 18 months from the date of manufacture displayed on the packaging. Store in the original, tightly closed and undamaged packaging, at a temperature between +5°C and +25°C, protected from direct sunlight.

PAINTS FORINTERIOR SURFACES

ULTRADIS®

Properties and use: In terms of quality ULTRADIS belongs to the first class of interior paints. It represents an ecological, dispersion, high-coverage and washable, acrylate-based paint. It provides good dirt resistance and high water vapour permeability. It is used for protection and decoration of interior wall surfaces made of concrete, extended render, aerated concrete, gypsum-cardboard panels, chipboard... It is available in white shade and as the basis for tinting in MAXIMIX system.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with some of GLETOLIN levelling compounds used for interior walls skimming. Prior to painting, impregnate the walls with an appropriate MAXIKRIL base coat depending on the surface condition. Apply two coats of ULTRADIS with a brush, short-haired roller or tank sprayer. The paint may be diluted with water up to 15%. Apply the second coat after 6 hours, i.e. when the first coat is fully dry. After application, immediately rinse the tools with water.


Consumption: 8-9m²/l for two-coat application, depending on the roughness and absorption capacity of the substrate.


MAXITON®

Properties and use: MAXITON is a top quality, high-coverage and water washable paint, supplied ready-to-use. It is made on acrylic binders basis, titanium oxide, fillers and special additives. It provides good adherence to the substrate, great coverage, water permeability and resistance to wet scrubbing. It is used for decorative protection of interior walls. It is available in shades in accordance with the MAXITON colour chart.

Manner of application: Surface must be dry, with good load-bearing capacity, clean, with no loose areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with some of GLETOLIN levelling compounds used for interior wall levelling. Prior to painting, impregnate the walls with an appropriate MAXIKRIL base coat depending on the surface condition. MAXITON does not need to be diluted with water since it is delivered in the ready-to-use state, it only requires thorough mixing to fully homogenise. Apply with a brush or a roller. When repainting clean surfaces, one coat of paint is enough. If the surface is not covered with an even coat of paint or if you wish to achieve a more intense shade, apply the second coat after 6 hours, i.e. when the previous coat is dry. After application, immediately rinse the tools with water.

Application temperature: Optimum application temperature ranges from +10°C to +30°C. It must not be used below +5°C.

Consumption: 128-185ml/m² in two coats, depending on the roughness and absorption capacity of the substrate.

Shelf life and storage: 18 months from the date of production stated on the packaging. Keep in the original, properly sealed and undamaged packaging at the temperatures from +5°C to +25°C, protected from the direct sunlight.

liter

1|2|5|10liter

1|2|5|10liter

2.5

141414

liter

0.5|1|3

MAXIDECOR

®

Oceano Properties and application: MAXIDECOR Oceano is a semi-transparent special effects paint of exquisite quality, made on water dispersion of acrylic binder, fillers, special additives and effect pigments. MAXIDECOR Oceano is a water-washable coating with good water vapour permeability, harmless to people and environment. It is easy to apply. It is used for protection and decoration of interior wall surfaces where a unique and alluring effect of sea waves is desired. It is produced in bases in accordance with MAXIDECOR Oceano colour chart.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with GLETOLIN G acrylic levelling compound. Then, apply a coat of MAXIDECOR Primer Nero primer in accordance with the producer’s instructions. When the primer is dry, apply MAXIDECOR Oceano which is supplied ready-to-use and only needs manual stirring to homogenise. MAXIDECOR Oceano of different batches and dates of production must always be homogenised! Apply MAXIDECOR Oceano with a special double MXD 2-70 brush in the manner that you dip one brush in one paint and the other brush in the second paint. Make sure not to change the order of paint application. Apply the paint in cross-directional movements, paying attention that the two shades do not cover each other. Due to open time, the surface to be painted by MAXIDECOR Oceano should not exceed

1.5m2 at the temperature ranging from 15-20°C. If the temperature is higher, reduce the surface area, i.e. slightly increase the area if the temperature is lower. When the paint has partially dried, use a dry brush to process the dry coat so that by moving MAXIDECEOR Oceano particle you create the effect which irresistibly reminds of sea waves. After the application, immediately rinse the tools with water.


Consumption: 12-14m2/l, depending on the surface roughness and absorption capacity, technique and manner of application.


151515

MAXIDECOR

®

MarmorinoProperties and application: MAXIDECOR Marmorino is a special-effects decorative render of exquisite quality, made on water dispersion of acrylic binder, specially selected aggregates, special additives and pigments. MAXIDECOR Marmorino creates a highly water-washable coating with good water vapour permeability, which is harmless to people and environment. It is used for protection and decoration of interior wall surfaces where an artistic and vintage appearance is desired. It can be tinted in accordance with MAXIDECOR Marmorino colour chart.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with GLETOLIN G acrylic levelling compound. After the surface is prepared apply MAXIDECOR Marmorino which is supplied ready-to-use and only needs manual stirring in order to homogenise. MAXIDECOR Maromorino tinted in MAXIMIX system and MAXIDECOR Marmorino of different batches and dates of production must always be homogenised! Apply the first coat of thickness approximately 1mm with a standard stainless steel broad knife over the entire area, trying to achieve the most level surface. Hold the broad knife at the angle of ≈15o. Leave the applied coat to dry for at least 6 hours prior to further processing at the temperature of 20oC. In order to achieve the most level surface, it can be sanded by sandpaper with particle size of 600 or 800. After sanding, remove the dust from the surface.Apply

the second coat using a trapeze stainless steel broad knife with round edges or a trowel. Apply the material with cross-directional movements over the previous coat in order to cover it partially. Take care that, when applying the material, the edges of the applied material partially overlap („spotting“ phase). Hold the broad knife at the angle of ≈30o. Further processing is possible after at least 12 hours at the temperature of 20oC Apply the third coat using a trapeze stainless steel broad knife with round edges or a trowel, in the same manner as described for the application of the second coat, only now apply the material on the areas where the second coat has not been applied, taking care that the edges of the new coat overlap the second coat. Hold the broad knife at the angle of ≈45o. After at least 24 hours have passed at the temperature of 20oC, start sanding the entire surface using sandpaper with particle size of 1000 applying a slight pressure. After sanding, remove the dust from the surface and start polishing the surface with a trapeze stainless steel broad knife with round edges. In order to achieve the best possible appearance, it is recommended to slightly sand the edges of the broad knife using sandpaper 1000. Clean the edges from dust caused by sanding. Apply a high but even and controlled pressure when polishing the surface. Polishing procedure is used to highlight the sheen and radiance of the material. After polishing of the material, MAXIDECOR Natural Wax can be applied in accordance with the producer’s instructions. This provides an additional shine and even better water-washable properties of the material. After the application, immediately rinse the tools with water.

Consumption: 2-3m2/l, depending on the surface roughness and absorption capacity, technique and manner of application.

DECORATIVE TREATMENT

For more information please see the product technical data sheet!

kg

1|5

16 16

liter

1|3

liter

1|3

liter

1|3


171717

MAXIDECOR

®

Antica Properties and use: MAXIDECOR Antica is a semi-transparent special effects paint made on basis of water dispersion of acrylic binder, fillers, special additives and pigments, enriched by special acrylic beads. MAXIDECOR Antica is a washable coating, with good water vapour permeability, harmless to people and environment and easy to apply. It is used for protection and decoration of interior wall surfaces where antique appearance is desired. It can be tinted in MAXIMIX system in accordance with MAXIDECOR Antica color chart.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose or crumbly areas, dust, water-

soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with GLETOLIN G acrylic levelling compound. Then, apply white ULTRADIS to the surface in accordance with the producer’s instructions. When ULTRADIS coat is dry, apply MAXIDECOR Antica which is supplied ready-to-use and only needs manual stirring to homogenise. MAXIDECOR Antica tinted in MAXIMIX system and MAXIDECOR Antica of different batches and dates of production must always be homogenised! Gradually apply the substance in small quantities to form one coat, brushing it in all directions on the surface area of 1-2m². In optimum conditions, 5-10 minutes after the application, treat the applied material with a plastic fan to break the acrylic beads and achieve the final appearance.


Consumption: 7-8m²/l depending on the roughness and absorption capacity of substrate, technique and manner of application.


MAXIDECOR

®

Sahara Properties and use: MAXDECOR Sahara is a special effects paint of superb quality made on basis of water dispersion of acrylic binder, fillers, special additives and special effect pigments. MAXIDECOR Sahara is a washable coating with good water vapour permeability, harmless to people and environment, easy to apply. It is used for protection and decoration of interior walls surfaces where an exciting and dynamic appearance is desired. It can be tinted in MAXIMIX system in accordance with MAXIDECOR Sahara colour chart.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically

removed. Level the uneven surfaces with a coat of GLETOLIN G acrylic levelling compound. Then, apply ULTRADIS coat tinted in the shade approximate to the shade of finishing material and in line with the producer’s instructions. When ULTRADIS coat is dry, apply MAXIDECOR Sahara which is supplied ready-to-use and only needs manual stirring to homogenise. MAXIDECOR Sahara tinted in MAXIMIX system and MAXIDECOR Sahara of different batches and dates of production must always be homogenised! Application technique No. 1: Gradually apply small quantity of MAXIDECOR Sahara to form one coat, brushing it in all directions, to the surface area of 1-2m². In optimum conditions, 5 to 10 minutes after the application, treat the applied material with a dry brush “playing” freely with the sandy area in order to achieve the final appearance and remove any visible brush strokes. Application

technique No. 2: Gradually apply small quantity of MAXIDECOR Sahara to form one coat using slanting, vertical or horizontal brush strokes to the surface area of 1-2m². In optimum conditions, 5-10 minutes after the application, treat the surface again with a dry brush in directions opposite to the previous ones in order to achieve the final appearance.




MAXIDECOR

® Nova Era Properties and use: MAXIDECOR Nova Era is a semi-transparent special effects paint made on basis of water dispersion of acrylic binder, fillers, special additives and pigments, enriched by special acrylic beads. MAXIDECOR Nova Era is a washable coating with good water vapour permeability, harmless for people and envi-ronment, easy to apply. It is used for protection and decoration of interior wall surfaces where antique appearance is desired. It can be tinted in MAXIMIX system in accordance with the MAXIDECOR Nova Era colour chart.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose or crumbly areas, dust, water-

soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with GLETOLIN G acrylic levelling compound. Then, apply white ULTRADIS to the surface in accordance with the producer’s instructions. When ULTRADIS coat is dry, apply MAXIDECOR Nova Era which is suppli-ed ready-to-use and only needs manual stirring to homogenise. MAXIDECOR Nova Era tinted in MAXIMIX system and MAXIDECOR Nova Era of different batches and dates of production must always be homogenised! Gradually apply the substance in small quantities to form one coat, brushing it in all directions on the surface area of 1-2m². In optimum conditions, 5-10 minutes after the application, treat the applied material with a plastic fan to break the acrylic beads and achieve the final appearance.

Application temperature: Optimum application

temperature ranges from +10°C do +25°C. It must not be used below +5°C.



181818

liter

1|3

MAXIDECOR

®

VelvetProperties and use: MAXIDECOR Velvet is a special effects paint of exceptional quality, made on basis of water dispersion of acrylic binders, fillers, special additives and special effect pigments. MAXIDECOR Velvet is a water washable coating with good water vapour permeability, harmless to people and environment. It is easy to apply. It is used for protection and decoration of interior wall surfaces where a subtle appearance, sophisticated like silk, is desired. It can be tinted in MAXIMIX system in accordance with MAXIDECOR Velvet colour chart.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with a coat of GLETOLIN G acrylic levelling compound. Then, apply MAXIDECOR Smooth Primer tinted in the similar shade of the finishing coat, in accordance with the producer’s instructions. When the primer is dry, apply MAXIDECOR Velvet which is supplied ready-to-use and only needs manual stirring to fully homogenise. MAXIDECOR Velvet tinted in MAXIMIX

system and MAXIDECOR Velvet of different batches and dates of production must always be homogenised! First apply one coat of paint using a brush in cross-direction movements in order to prepare the coat for further processing. While the applied paint is still wet, create the desired effect of “depth” using a stainless steel or plastic trowel with round edges. The trowel must be positioned at an angle of about 30° in relation to the surface and slightly pressed. In case you do not want to use the trowel, you can create the desired effect using only a brush: apply gradually the material in smaller amounts in one coat by cross- direction or semi-circular brush movements. After application, immediately rinse the tools with water.


Consumption: 12-14m2/l, depending on the surface roughness of absorption capacity of the substrate, technique and application manner.

Shelf life and storage: 18 months from the date of production stated on the packaging. Keep in the original, properly sealed and undamaged packaging at the temperatures ranging from +5°C do +25°C, protected from the direct sunlight.


191919

liter

1|3

MAXIDECOR

®

GlamourProperties and use: MAXIDECOR Glamour is a top-quality metallic colour made on basis of water dispersion of acrylic binder, fillers, special additives and special effect pigments. MAXIDECOR Glamour is a washable coating with good water vapour permeability, harmless to people and environment and easy to apply. It is used for protection and decoration of interior wall surfaces where elegant and modern appearance is desired. It can be tinted in MAXIMIX system in accordance with MAXIDECOR Glamour colour chart.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with GLETOLIN G acrylic levelling compound. Then, apply a coat of ULTRADIS tinted in the shade approximate to the shade of finishing material in line with the producer’s instructions. When ULTRADIS coat is dry, apply MAXIDECOR Glamour which is supplied ready-to-use and

only needs manual stirring to homogenise. MAXIDECOR Glamour tinted in MAXIMIX system and MAXIDECOR Glamour of different batches and dates of production must always be homogenised! Gradually apply the substance in small quantities to form one coat, brushing it in all directions on the surface area of 1-2m². In optimum conditions, 5-10 minutes after the application, treat again the applied material with a dry brush to achieve the final appearance.




20

kg

20

MAXIDECOR

®

Travertino Properties and application: MAXIDECOR Travertino is a special decorative dry type of render, used for decorative protection of interior and exterior mineral surfaces. It has been carefully designed of specially selected marble aggregates, high quality cement, polymers and additives in order to replicate the natural stone effect with accentuated “veins” and texture. It is distinguished by its excellent adherence to mineral substrates, good water vapour permeability, excellent water repellence and resistance to weather conditions and UV rays.

Substrate preparation: The surface must be flat, dry and clean, with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities that could prevent its good adhesion to the substrate. Leave the rendered surfaces to dry for 28 days and the finishing coat of adhesive and reinforcement mortar for 7 days. Prior to the application the surface must be grouted. With newly rendered surfaces and surfaces with lower load-bearing capacity, walls must be impregnated with MAXIKRIL Hidrosol base. When MAXIKRIL Hidrosol is dry, apply the white ROLOGRUND.

Material preparation: Add 20kg of MAXIDECOR Travertino to 5.0-5.5l of water and mix it to achieve a homogenous mass with no lumps, but not for too long in order to avoid foam formation which could cause problems with application. If the foam

has formed, leave the material to rest for 15-20 minutes and then apply it to the substrate. The prepared mixture must be used within 2 hours.

Manner of application: Apply an even coat of MAXIDECOR Travertino using a stainless broad knife so that the coat thickness is approximately 1.5 to 2.0mm. 10-15 minutes after the application (depending on the weather conditions), i.e. as soon as the material starts to dry, start creating the texture using the appropriate tools (e.g. tools with artificial grass) in order to create „veins“ which are typical for travertine natural stone, the imitation of which should be achieved. After that, use the stainless broad knife to even out the surface by applying a larger pressure in order to create the natural stone texture. When the application procedure is finished, start „cutting“ the applied material in order to achieve the imitation of stone blocks. “Cut” the material with a rounded corner of a smaller spatula or a screwdriver creating blocks of appropriate size. In order to create fully horizontal and vertical lines, use a large level as a guide. After the application, immediately rinse the tools with water.

Painting technique: MAXIDECOR Travertino is painted with special semi-transparent coat of MAXIDECOR Velatura, at least 24 hours after its application and in line with the producer’s instructions.

Consumption: ≈2 kg/m2, depending on the technique and manner of application as well as the quality of the substrate.


21

liter

1


MAXIDECOR

®

VelaturaFeatures and purpose: MAXIDECOR Velatura is a semi-transparent effective colour, made based on aqueous dispersions of acrylic binder and special additives. MAXIDECOR Velatura is a washable coating, with good water vapour permeability, harmless to humans and the environment, easy to apply. It is designed for protection and decoration of exterior and interior wall surfaces, where it is necessary to achieve a soft and subtle look. It is used alone and can also be used in combination with other decorative materials, especially for shading of MAXIDECOR Travertino decorative plaster. It is tinted to the MAXIMIX system according to the tint card of MAXIDECOR Velatura.

Manner of work: The surface must be: dry, carryable, clean and free of loose materials, dust, water-soluble salts, grease and other contaminants. Old paint, which is not bound, is to be mechanically removed. Uneven surfaces to be evened by GLETOLIN skim mass. Before painting, the walls should be impregnated with the appropriate MAXIKRIL base, depending on surface conditions. During decorative treatment of interior walls, before the installation of MAXIDECOR Velatura, apply the white MAXIDECOR Smooth Primer, that is, the white MAXIFAS for external walls, with roller or spray machine, to the two cover layers. After drying of the MAXIDECOR Smooth Primer or MAXIFAS, apply the MAXIDECOR Velatura, which is supplied ready

for use, it is only to be hand-mixed until becoming homogeneous. MAXIDECOR Velatura tinted on the MAXIMIX system and MAXIDECOR Velatura with different batch and date of manufacture must be homogenised! The material in smaller amounts is gradually applied in a single layer, with brush strokes in all directions on a surface of 1-2m2. Under optimal conditions, 5 to 10 minutes after application, again stroke the dry brush over the coating, in order to achieve the final look. When painting MAXIDECOR Travertino, it is necessary to impregnate it with MAXIKRIL Hydrosol base. When the primer dries (min. 6 hrs), apply the MAXIDECOR Velatura with a brush, roller, or sponge, and then immediately remove the extra material with a sponge. After use, wash the tool immediately with water.

Working temperature: The optimum working temperature is between +10°C and +25°C. It should not be used below +5°C.

Consumption: 10-20m2/l, depending on the roughness and absorption, as well as application techniques.

Expiration and storage: 18 months from the manufacture date stated on the packaging. Store in original, well closed, and undamaged package at temperature from +5°C to +25°C, protected from direct sunlight.

22

PAINTS AND COATS FOR EXTERIOR SURFACES

BETAKRIL®

Properties and use: BETAKRIL is a high-quality acrylic paint for concrete. It provides good adhesion to the substrate, excellent water repellence, covering power, durability against the weather conditions and UV rays, good water vapour permeability and alkaline resistance. It is used for protection and decoration of vertical exterior and interior concrete surfaces as well as concrete roofing tiles. It does not endure high mechanical loads and is partially resistant to the effect of diluted acids, bases and other chemicals. It is available in 9 basic shades and as the basis for tinting in MAXIMIX system.

Manner of application: The surface must be dry, with good load-bearing capacity, clean, with no loose and crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanicaly removed. Level the uneven surfaces with GLETOLIN levelling compound used for exterior walls levelling. Prior to coating, impregnate the surfaces with an appropriate MAXIKRIL base coat depending on the surface condition. Apply BETAKRIL with a brush, roller or tank sprayer in two coats. It may be diluted with water up to 15%. Apply the second coat after 6 hours, i.e. when the previous coat is fully dry. After application, immediate rinse the tools with water.




MAXIFAS®

Properties and use: MAXIFAS is a high-quality facade paint acrylate-based. It provides good adherence to the substrate, excellent covering power, water vapour permeability, water repellence and durability against the weather and UV rays. It is used for protection and decoration of exterior and interior surfaces made of concrete, extended render, aerated concrete, asbestos cement, etc. It is not recommended for painting new, not yet carbonised lime and lime-cement surfaces (for 28 days minimum). It is available in white shade as well as the basis for tinting in MAXIMIX system.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose and crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with some of GLETOLIN levelling compounds used for exterior walls levelling. Prior to painting, impregnate the surfaces with the appropriate MAXIKRIL base coat depending on the surface condition. Apply two coats of MAXIFAS with a brush, roller or tank sprayer. The paint may be diluted with water up to 15% maximum. Apply the second coat after 6 hours, i.e. when the first coat is fully dry. After application, immediately rinse the tools with water.




MAXIFAS® ColorProperties and use: MAXIFAS Color is a high-quality, tinted facade paint based on acrylates. It provides good adherence to the substrate, excellent covering power, water vapour permeability, water repellence and durability against the weather and UV rays. It is used for protection and decoration of exterior and inte-rior wall surfaces as well as for tinting MAXIFAS, MAXIPOL and MAXIDIS. It is not recommended for painting new, not yet carbonised and lime-cement surfaces (for 28 days minimum).

Manner of application: Surface must be dry, with good load-bearing capacity, clean, with no loose areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with some of GLETOLIN levelling compound used for exterior wall levelling. Prior to painting, impregnate the surfaces with an appropriate MAXIKRIL base coat depending on the surface condition. For intense yellow, orange and red shades we recommend to even the surface with a coat of white paint. Apply two coats of MAXIFAS Color with a brush, roller or tank sprayer. The paint may be diluted with water up to 15% maximum. Apply the second coat after 6 hours, i.e. when the first coat is fully dry. After application, immediately rinse the tools with water.


Consumption: 175-300ml/m² for two-coat application, depending on the roughness and absorption capacity of surface.


liter

0.65|3|5|15liter

0.65|3|5|15liter

0.65|3|5|15

23

HIDROFOB® MProperties and use: HIDROFOB M is a colourless silicone coating used for long-term protection of facade bricks, marble, stone, sprayed and hammer-peened facades, etc. against the we-ather, efflorescence and micro organisms attack. HIDROFOB M coat does not affect the colour and gloss of the coated surfaces.

Manner of application: Prior to application stir well HIDROFOB M and it is ready for use! The surface must be dry, clean, dust and grease-free in order to achieve long-term protection. Apply to the facade with a brush, roller or tank sprayer. Apply two coats of HIDROFOB M on highly porous surfaces using the „wet on wet“ principle. After application, immediately rinse the tools with water.


Consumption: 200-500ml/m² depending on the roughness and absorption capacity of the substrate.


MAXIFAS® STProperties and use: MAXIFAS ST is a high-quality facade paint based on potassium water glass, acrylic and silicone binders. It is alkaline resistant with excellent water vapour permeability, good water repellence, and resistance to dirt weather and UV rays. It is used for protection and decoration of exterior and interior mineral surfaces. Due to its outstanding properties, it is recommended for renovation of old buildings. It is available in white shade and may be tinted in MAXIMIX system in shades with ST designation.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose and crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with an appropriate GLETOLIN levelling compounds used for exteri-or walls levelling. Prior to painting, impregnate the surfaces with MAXISIL SN primer. After the primer is dry, apply two coats of MAXIFAS ST with a brush, roller or tank sprayer. The paint may be diluted with water up to 15% maxi-mum. Apply the second coat after 12 hours, i.e. when the first coat is fully dry. After application, immediately rinse the tools with water.

Application temperature: Optimum applicati-on temperature ranges from +10°C do +25°C. It must not be used below +8°C as well as in bright sunshine, wind, for and rain. Protect the newly coated surfaces, in optimum conditions, from the weather impact for at least 24 hours.

Consumption: 175-300ml/m² for two-coat application, depending on the roughness and absorption capacity of the surface.

Shelf life and storage: 9 months from the date of production stated on the packaging. Keep in the original, properly sealed and undamaged packaging at the temperatures from +5°C do +25°C, protected from the direct sunlight. Keep out of children’s reach.

MAXIFAS® SNProperties and use: MAXIFAS SN is a high-quality facade paint based on silicone binders. It provides good adherence to the substrate, excellent coverage, outstanding water repellen-ce and high water vapour permeability and durability against the weather and UV rays. It is used for protection and decoration of exterior and interior mineral surfaces. It is available in white shade as well as the basis for tinting in MAXIMIS system.

Manner of application: Surface must be dry, with good load-bearing capacity, clean and with no loose and crumbly areas, dust, water-soluble salts, grease and other impurities. The old, loose paint must be mechanically removed. Level the uneven surfaces with an appropriate GLETOLIN levelling compound used for exterior walls levelling. Prior to painting, impregnate the surfaces with MAXISIL SN primer. After the primer is dry apply two coats of MAXIFAS SN with a brush, roller or tank sprayer. The paint may be diluted with water up to 15% maximum. Apply the second coat after 6 hours, i.e. when the first coat is fully dry. After application, immediately rinse the tools with water.




liter

3|5|15liter

3|5|15liter

1|18

24

WOOD PAINTS AND COATS

AQUAMAX® Wood PrimerProperties and use: AQUAMAX Wood Primer is ecological, finishing, high-quality, base coat for wood based on water dispersion of acrylates. It blocks well tannin and other water-soluble stains. It is used for protection of exterior and interior wooden surfaces (windows, doors, fences, wooden roof structures, eaves, etc.) before the AQUAMAX Wood Paint enamel coat are applied. It is available in matt white shade.

Manner of application: Wooden surface must be clean, dry, form and sanded. Prior to the first coating, protect the surfaces which are not located indoors in frequently used premises with AQUAMAX Impregnant. It is enough to rub in advance the old, well preserved coats with fine sandpaper. Badly adhering coats must be fully removed. Uneven areas must be filled and levelled with AQUAMAX Wood Kit. Our recommendation is to apply two coats of AQUAMAX Wood Primer, particularly with wood rich in tannin (oak, beech, chestnut) and knotty wood. Apply the coats with brush or roller, when it may be diluted with water up to 5% (and up to 10% if applied with tank sprayer). The tannin blocking capability is reduced by diluting. Apply the second coat after 6 hours, i.e. when the pre-vious coat is fully dry. Treat the dry coat with fine sand paper in order to remove any loose wood fibre. Dry primer has no odour. After application, immediately rinse the tools with water.

Application temperature: Optimum application temperature for the coating, wood and work area ranges from +10°C do +30°C. It must not be used at the relative humidity higher than 80% as well as strong sunshine, wind, fog and rain.

Consumption: ≈11m²/0.65l for one-coat application, depending on the quality of prepared surfaces and manner of application.


AQUAMAX® Wood & Metal PaintProperties and use: AQUAMAX Wood & Metal Paint is ecological, high-quality enamel for wood based on water dispersion of acrylates. It has a distinctive whiteness, durability (does not yellow), excellent covering power and resistance to the weather elements and UV rays. It is used for protection and decoration of exterior and in-terior wooden surfaces (windows, doors, fences, wooden roof structures, eaves, etc.). Practically, it has no odour. It is available as high-gloss, semi-gloss and matt white shade. It can be tinted in MAXIMIX system.

Manner of application: Wooden surface must be clean, dry, firm and sanded. Prior to the first coat, protect the surfaces which are not located indoors in frequently used premises with AQUAMAX Impregnant. It is enough to rub in advance the old, well preserved coats with fine sandpaper. Badly adhering coats must be fully removed. Uneven areas must be filled and le-velled with AQUAMAX Wood Kit. Prior to enamel application apply the base coat of AQUAMAX Wood Primer to the previously prepared surfaces. Apply two coats of AQUAMAX Wood & Metal Paint. The paint may be diluted with water up to 10% if applied with a brush or roller (or up to 20% if applied with tank sprayer). The more diluted the paint, the less covering power it provides. Apply the second coat after 6 hours, i.e. when the previous coat is fully dry. Dry paint has no odour. After application, immediately rinse the tools with water.

Application temperature: The optimum appli-cation temperature for the coating, wood and work area ranges from +10°C do +30°C. It must not be used at relative humidity higher than 80% as well as bright sunshine, wind, for and rain.

Consumption: ≈11m²/0.65l for one-coat application, depending on the quality of the prepared surfaces and manner of application.


AQUAMAX® ImpregnantProperties and use: AQUAMAX Impregnant is a wood impregnating agent based on water dispersion of acrylic binders. By careful formu-lation we have designed the fungus-resistant coating which stabilizes wood colour, provides a more even paint application, less absor-bent surfaces and finishing coats with better adhesion. It is intended for interior and exterior surfaces. It is easy to apply and dries quickly. The product does not have any unpleasant odours.

Manner of application: Wood surface must be clean, dry, firm and sanded. AQUAMAX Impregnant is ready to use and must not be diluted with water or other agents, it only requires stirring. Apply one coat using a brush, roller or tank sprayer. After it has dried and prior to the application of the finishing coat use a fine sandpaper to slightly sand the surface. Apply the finishing coat after 6 hours, i.e. when the previous coat is fully dry. After the application, immediately rinse the tools with water.

Application temperature: The optimum appli-cation temperature for the coating, wood and work area ranges from +10°C do +30°C. It must not be used at the relative humidity higher than 80% as well as in bright sunshine, wind, fog and rain.

Consumption: ≈9m²/0.65l for one-coat appli-cation, depending on the quality of prepared surfaces and manner of application.

Shelf life and storage: 18 months from the date of production stated on the packaging. Keep in the original, properly sealed and undamaged packaging at the temperatures ranging from +5°C do +25°C, protected from the direct sunlight. Keep out of children’s reach.

liter

0.65|5|15liter

0.65|5|15liter

0.65|3

25

SUPPLEMENTARYPRODUCTS

AQUAMAX® Lasur TopProperties and use: AQUAMAX Lasur TOP is a thick transparent stain based on water dispersion of acrylic binders. It is enriched by wax, special additives, special UV absorbers and stabilizers. It is used for protection and decoration of exterior and interior wooden surfaces. AQUAMAX Lasur TOP is a carefully created coating designed to emphasize the natural wood grain and texture while protecting the wood from UV rays, moisture and other weather conditions. It is easy to apply and dries quickly. It does not have any unpleasant odours, therefore it is both user and environmentally friendly. It is available as colourless or tinted coating in accordance with the AQUAMAX Lasur TOP colour chart.

Manner of application: Wooden surface must be clean, dry, firm and sanded. Prior to the first coating, protect the interior and exterior wooden surfaces with the AQUAMAX Impregnant protective agent-fungus-resistant wood coating. Apply two coats of pigmented AQUAMAX Lasur TOP and three coats of colourless AQUAMAX Lasur TOP. It may be diluted with water up to 5% maximum. Apply the second coat after 6 hours, i.e. when the previous coat is fully dry. Dry lasure coating has no odour. After application, immediately rinse the tools with water.

Application temperature: The optimum application temperature for the coating, wood and work area ranges from +10°C to +30°C. It must not be used at relative humidity higher than 80%, as well as in bright sunshine, wind, fog and rain.

Consumption: ≈11m²/0.65l for one-coat application, depending on the quality of the prepared surfaces and manner of application.

Shelf life and storage: 18 months from the date of production stated on the packaging. Keep in the original, properly sealed and undamaged packaging at the temperatures ranging from +5°C do +25°C, protected from the direct sunlight.

MAXI® COLOR

Properties and use: MAXI Color is a high quality pigment preparation used for manual tinting of interior wall paints. Maximum quantity is 3 bottles of MAXI Color per 15l of paint.

Manner of application: Prior to use shake well the MAXI Color bottle, and then mix it with the paint either by mixer or hand to fully homogenise.


MAXICID® StandardProperties and use: MAXICID is a coat with addition of special fungicide and algaecide. It is used to destroy wall algae and mould on interior wall surfaces. It affects a wide range of wall algae and mould and after the MAXICIDE treatment the green colour of wall algae completely vanishes.

Manner of application: Prior to application, shake well the MAXICID bottle and it is ready to use! Apply with a roller or a brush on the surfa-ces visibly infected by mould and algae as well as on surfaces which are suspected of infection. The effect time of the applied MAXICID on the infected surfaces and prior to paint coating is at least 24 hours. Remove the destroyed algae and mould from the treated surface by dry scrubbing. If the wall areas are more infected, repeat the procedure. Afterwards, apply a coat of MAXIDIS F, washable dispersion paint resistant to fungus and mould. After application, immedia-tely rinse the tools with water.

Application temperature: From +5°C to +35°C.

Consumption: 100-200ml/m² depending on the infection degree, substrate roughness and absorption capacity.

Shelf life and storage: 12 months from the date of production stated on the packaging. Keep in the original, properly sealed and undamaged packaging at the temperatures ranging from +5°C do +25°C, protected from direct sunlight. Keep out of children’s reach.

liter

0.65|3|10liter

0.5|18ml

100

26

grams

200|800kg

7|20grams

200|800kg

7|20kg

1|5|25

WOOD AND PARQUET ADHESIVES

MAXIFIX® D5Properties and use: MAXIFIX D5 is used in furniture industry for lengthwise and widthwise jointing of soft wood and especially hard wood, chair binding, in fact, in all cases where high strength of glued joints is required.

Manner of application: MAXIFIX D5 is ready to use, only thorough stirring is required. It can be applied both by hand and a machine. Bonding surface must be smooth, dry, free of dust and grease. Further treatment of bonded surfaces is possible 24 hours after the bonding moment.

Application requirements: Pressing pressure: 0.4-0.5 MPa; pressing time: 120 minutes; relative wood moisture content: up to 10%; temperature of the adhesive, wood and ambient should be from +15°C to +25°C; the lowest application temperature is 12°C. Air humidity: 60%.

Consumption: 0.15-0.2kg/m².


MAXIFIX® D3Properties and use: MAXIFIX D3 is used for bonding wood, in production of facade joinery, as well as for bonding some flooring types and production of laminated profiles. In fact, it is used for all lengthwise and widthwise wood joints, exposed to increased humidity or short-term water impact.

Manner of application: MAXIFIX D3 is ready to use, only thorough stirring is required. It can be applied both by hand and a machine. Bonding surface must be smooth, dry, free of dust and grease. Further treatment of bonded surfaces is possible 24 hours after the bonding moment.

Application requirements: Pressing pressure: 0.4-0.5 MPa; pressing time: 120 minutes; relative wood moisture content: up to 10%; temperature of the adhesive, wood and ambient should be from +15°C to +25°C; the lowest application temperature is 12°C.

Consumption: 0.15-0.2kg/m².


MAXIKOL® KPProperties and use: MAXIKOL KP is used for bonding all classic parquets and all wooden prefabricated small-size products to concrete, wood and similar substrates.

Manner of application: Surface must be: clean, firm, dry, pressure resistant, free of dust, loosely bonded areas and grease. Levelling of uneven floors by SAMOLIV is first required. Before applying adhesive, surfaces must be grouted by an adequate MAXIKRIL primer depending on the surface condition. Due to its drying time, the adhesive must not be applied to a surface larger than 1-2m² before parquet is laid. MAXIKOL KP is ready to use. Apply MAXIKOL KP with a notched spatula. Lay the parquet on the applied adhesive and press well. Walking on is possible after 24 hours. Further parquet treatment, sanding and lacquering can be performed 5 days after bonding.

Application requirements: Humidity of concrete substrate is 2.5% maximum; relative parquet moisture content: 9%; application temperature of air, substrate and parquet should be from +15°C do +25°C; the lowest application temperature is 12°C.

Consumption: 0.8-2.0kg/m² depending on the substrate preparation and manner of application.


27

MAXIKOL® PU 610Properties and use: MAXIKOL PU 610 is a high-quality, two-part adhesive made on basis of polyurethane, fillers and additives. It is used for bonding all parquet types, wooden and lamina-te flooring. It can be applied to both absorbent and non-absorbent substrates where moisture content does not exceed 2%. It provides good adhesion and flexibility, thus it can be used with underfloor heating systems.

Manner of application: Surface must be: clean, firm, dry, pressure resistant, free of dust, loosely bonded areas and grease. Levelling of uneven floors by SAMOLIV is first required. MAXIKOL PU 610 consists of two components, a hard A component and a liquid B component. The ratio of mixing is A:B=6:1. Add the components in the prescribed ratio and stir the compound for 5 minutes. Then, the adhesive is ready to use. If the moisture content of the substrate exceeds 2%, it must be treated with MAXIKOL PU primer. Hardening starts after 40 minutes at the tempe-rature of +20°C. Open time as well as the time of full hardening depends on the ambient tempe-rature where adhesion procedure is performed. Apply the adhesive with a notched trowel in line with the prescribed standards which differ in relation to the material type which is bonded. Further processing of parquet, sanding and lacquering, can be performed at least 6 hours after the bonding. Clean the tools before the adhesive has bonded (by cloth, paper...).

Application temperature: From +15°C to +25°C.

Consumption: 0.8-2.0kg/m², depending on substrate preparation and manner of application.


MAXIKOL® PU PrimerProperties and use: MAXIKOL PU Primer is a top-quality one-part polyurethane primer. It is used as a foundation coat for screed consolidation as well as for underfloor heating systems prior to application of MAXIKOL PU adhesives. It can be used on both absorbent and non-absorbent sur-faces where the moisture content is lower than 3.5%. It penetrates deep into absorbent surfaces, improves adhesion of adhesives and reduces absorption of the substrate.

Manner of application: Surface must be dry, clean, solid, pressure resistant and free of dust, loosely bonded areas and grease. The moisture content of substrate when laying parquet flooring must not exceed 2.4%, while, if using MAXIKOL PU Primer, the moisture content of the substrate may be up to 3.5%. MAXIKOL PU Primer is a ready-made product. Apply the primer using a short-haired roller or fine brush. With very absorbent surfaces, apply the primer in two coats. Apply the second coat on the fully dry previous coat (after 2-3 hours). If used as an impregnation agent, apply MAXIKOL PU Primer until the substrate is fully saturated. In optimum conditions adhesive can be applied 4 hours after the primer application.

Application temperature: Optimum application temperature ranges from +18°C to +25°C, with maximum relative humidity of 60%. It must not be used below +15°C.

Consumption: 100-300ml/m², depending on the substrate roughness and absorption capacity as well as on manner of application.


liter

4kg

9kg

1.5+ 1.5A B

28

CERAMICS PROGRAMME

KERAMOL® PlusProperties and use: KERAMOL Plus is an adhesive for ceramic tiles based on hydraulic binders, specially selected aggregates, synthetic polymers and additives. It is suitable for laying ceramic tiles, stone mosaics and stone tiles. It is used for laying ceramic tiles on interior wall and floor surfaces as well as for premises with short-term increased humidity impact (kitchens, bathrooms, toilets) and for exterior application when laying absorbent tiles on absorbent surfaces.

Manner of application: Add a 25kg bag of KERAMOL Plus to 7l of water and mix until a homogenous, lump-free compound is achieved. Leave it for 15 minutes and then thoroughly mix again. Compound prepared in such a manner is ready for application and must be used within 2 hours. Surfaces to which this adhesive is applied must have good load-bearing capacity and be free of dust, grease and other impurities. Larger uneven areas must be filled with KERAMOL Plus adhesive a day before the tiles are to be laid. Before the adhesive is applied, surfaces must be grouted with an appropriate MAXIKRIL primer depending on the surface condition. Apply the adhesive with a notched trowel in the manner that minimum 65% of the tile area is covered by the adhesive. When bonding heavy ceramic tiles, application of an additional coat of adhesive is recommended. Position the tiles on the applied adhesive moving them in left to right and up to down direction. Fill the joints between the tiles with FUGALIN joint filler at least 24 hours after the tiles have been laid. After application, immediately rinse the tiles and tools with water.

Application temperature: Perform the opera-tions at the temperatures ranging from +5°C to +30°C. Weather conditions may affect the bonding process.

Consumption: From 2-5kg/m², depending on the quality of prepared surfaces, technique and manner of application.


KERAMOL® FlexProperties and use: KERAMOL Flex is a flexible adhesive for ceramic tiles based on hydraulic binders, specially selected aggregates, synthetic polymers and additives. It is used for interior non-absorbent tiles and exterior non-absorbent tiles which are laid on absorbent floor surfaces. It is stable at temperatures ranging from -20°C to +70°C. It is recommended for application in bat-hrooms, kitchens, underfloor heating systems, swimming pools, balconies and terraces, in fact, for all situations where the tiles are exposed to increased humidity and temperature changes.

Manner of application: Add a 25kg bag of KERAMOL Flex to 7l of water and mix until a homogenous, lump-free compound is achieved. Leave it for 15 minutes and then thoroughly mix again. Compound prepared in such a manner is ready for application and must be used within 2 hours. Surfaces to which this adhesive is applied must have good load-bearing capacity and be free of dust, grease and other impurities. Larger uneven areas must be filled with KERAMOL Flex adhesive a day before the tiles are to be laid. Before the adhesive is applied, surfaces must be grouted with an appropriate MAXIKRIL primer depending on the surface condition. If “tile to tile” bonding is carried out, grout the surfaces with MAXIKRIL Ceramic primer. Apply the adhesive with a notched trowel in the manner that, for interior application, minimum 65% of the tile area is covered by the adhesive while, for exterior application, the entire tile surface must be covered by adhesive. Position the tiles on the applied adhesive moving them in left to right and up to down direction. Fill the joints between the tiles with FUGALIN joint filler at least 24 hours after the tiles have been laid. After application, immediately rinse the tiles and tools with water.




KERAMOL® InteriorProperties and use: KERAMOL Interior is an adhesive for ceramic tiles based on hydraulic binders, specially selected aggregates and additi-ves. It is suitable for laying ceramic tiles, natural absorbent stone and terracotta tiles as well as Siporex, i.e. autoclaved aerated concrete blocks. It is recommended for laying ceramic tiles on interior absorbent wall and floor surfaces.

Manner of application: Add a 25kg bag of KERAMOL Interior to 7l of water and mix until a homogenous, lump-free compound is achieved. Leave it for 15 minutes and then thoroughly mix again. Compound prepared in such a manner is ready for application and must be used within 2 hours. Surfaces to which this adhesive is applied must have good load-bearing capacity and be free of dust, grease and other impurities. Larger uneven areas must be filled with KERAMOL Inte-rior adhesive a day before the tiles are to be laid. Before the adhesive is applied, surfaces must be grouted with an appropriate MAXIKRIL primer depending on the surface condition. Apply the adhesive with a notched trowel in the manner that minimum 65% of the tile area is covered by the adhesive. Position the tiles on the applied adhesive moving them in left to right and up to down direction. Fill the joints between the tiles with FUGALIN joint filler at least 24 hours after the tiles have been laid. After application, imme-diately rinse the tiles and tools with water.




kg

5|25kg

5|25kg

25

29

kg

25kg

25kg

2|20

KERAMOL® EWProperties and use: KERAMOL Elastic White is a highly elastic adhesive for ceramic tiles based on white cement, specially selected aggregates, synthetic polymers and additives. It is used for exterior and interior wall and floor surfaces for bonding transparent stone, marble, lime, cera-mics and mosaics and glass prisms. It does not change the colour of used materials. It is stable at temperatures ranging from -20°C to +70°C. It is recommended for application in bathrooms, kitchens, underfloor heating systems, swimming pools, balconies and terraces, in fact, for all situ-ations where the tiles are exposed to increased humidity and temperature changes. It is ideal for bonding non-absorbent tiles to demanding, critical and deformation-prone surfaces.Manner of application: Add a 25kg bag of KERAMOL Elastic White to 7l of water and mix until a homogenous, lump-free compound is achieved. Leave it for 15 minutes and then thoroughly mix again. Compound prepared in such a manner is ready for application and must be used within 2 hours. Surfaces to which this adhesive is applied must have good load-bearing capacity and be free of dust, grease and other impurities. Larger uneven areas must be filled with KERAMOL Elastic White adhesive a day before the tiles are to be laid. Before the adhesive is applied, surfaces must be grouted with an appropriate MAXIKRIL primer depending on the surface condition. If “tile to tile” bonding is carried out, grout the surfaces with MAXIKRIL Ceramic primer. Apply the adhesive with a notched trowel in the manner that minimum 65% of the tile area is covered by the adhesive. Position the tiles on the applied adhesive moving them in left to right and up to down direction. Fill the joints between the tiles with FUGALIN joint filler at least 24 hours after the tiles have been laid. After application, immediately rinse the tiles and tools with water.Application temperature: Perform the opera-tions at the temperatures ranging from +5°C to +30°C. Weather conditions may affect the bonding process.Consumption: From 2-5kg/m², depending on the quality of prepared surfaces, technique and manner of application.Shelf life and storage: 12 months from the date of production stated on the packaging. Keep in a properly sealed and undamaged packaging in dry and well aerated premises.

FUGALIN®

Properties and use: FUGALIN is a water repellent, water vapour permeable, elastic, fungicide protected tile joint filler with excellent adhesion to surfaces and scratch resistance. It is used for filling joints of ceramics and glass tiles, mosaics and stone tiles for both interior and exterior operations. It is used both for wall and floor surfaces. Maximum joint width must not exceed 10mm. Due to its excellent technical properties FUGALIN is suitable for application in bathrooms, kitchens as well as in interior premi-ses with underfloor heating. FUGALIN is available in various shades in line with the MAXIMA joint fillers colour chart.Manner of application: Add a 2kg pail of FUGALIN to ≈600ml of water and mix well with a mixer. Leave it for 5-10 minutes and then thoroughly mix it again. The compound prepa-red in this manner is ready for application and must be used within 2 hours. Apply FUGALIN with a rubber skimmer at a sloping angle to the direction of joints, pressing it well into the joints. The surface to which FUGALIN is applied must previously be sprayed with water. After the application, approximately 10-15minutes later, use a fine sponge for joints to wipe the entire tiles and joints area and then polish with a dry cloth. Water repellence of FUGALIN is reached 5-7 days after the application. For highly porous and rough tiles, check the cleaning instructions prior to FUGALIN application. If the adhesive used for tile bonding is not fully dry, the colour of joint filler may change. It is allowed to walk on the tiles 12 hours after the application of FUGALIN. After application, immediately rinse the tools with water.Application temperature: Optimum applica-tion temperature ranges from +10°C to +30°C. It must not be used below +5°C as well as in bright sunshine, wind, fog or rain.Consumption: From 0.5-1.0kg/m², depending on the joint width and depth as well as the tile size.Shelf life and storage: 24 months from the date of production stated on the packaging. Keep in a properly sealed and undamaged packaging in dry and well aerated premises.

KERAMOL® ElasticProperties and use: KERAMOL Elastic is a highly elastic adhesive for ceramic tiles based on hydraulic binders, specially selected aggregates, synthetic polymers and additives. It is used for exterior and interior wall and floor surfaces. It is stable at temperatures ranging from -20°C to +70°C. It is recommended for application in bathrooms, kitchens, underfloor heating systems, swimming pools, balconies and terraces, in fact, for all situations where the tiles are exposed to increased humidity and temperature changes. It is ideal for bonding non-absorbent tiles to demanding, critical and deformation-prone surfaces.Manner of application: Add a 25kg bag of KERAMOL Elastic to 7l of water and mix until a homogenous, lump-free compound is achieved. Leave it for 15 minutes and then thoroughly mix again. Compound prepared in such a manner is ready for application and must be used within 2 hours. Surfaces to which this adhesive is applied must have good load-bearing capacity and be free of dust, grease and other impurities. Larger uneven areas must be filled with KERAMOL Elastic adhesive a day before the tiles are to be laid. Before the adhesive is applied, surfaces must be grouted with an appropriate MAXIKRIL primer depending on the surface condition. If “tile to tile” bonding is carried out, grout the surfaces with MAXIKRIL Ceramic primer. Apply the adhesive with a notched trowel in the manner that minimum 65% of the tile area is covered by the adhesive. Position the tiles on the applied adhesive moving them in left to right and up to down direction. Fill the joints between the tiles with FUGALIN joint filler at least 24 hours after the tiles have been laid. After application, immediately rinse the tiles and tools with water.Application temperature: Perform the opera-tions at the temperatures ranging from +5°C to +30°C. Weather conditions may affect the bonding process.Consumption: From 2-5kg/m², depending on the quality of prepared surfaces, technique and manner of application.Shelf life and storage: 12 months from the date of production stated on the packaging. Keep in a properly sealed and undamaged packaging in dry and well aerated premises.

30

WATERPROOFING COATS

HIDROMAX® LasticProperties and application: HIDROMAX Lastic 1k is an elastic powdery compound made on basis of cement and specially selected aggregates, im-proved by water repellent, waterproof and alkaline resistant polymers, fibre reinforced, enriched by special additives for waterproofing and protection of cement surfaces. It has crack-bridging properties, excellent adherence to mineral surfaces and can be applied to wet substrates. When mixed with water, a paste-like compound is achieved which can be applied with a brush or metal trowel. It is used for protection of buildings from rising capillary damp, penetration of water under pressure as well as in situations where waterproofing capacity must be ensured due to positive and negative hydrostatic pressure. It is recommended for waterproofing of kitchens, bathrooms, dug walls, basement and cellar premises, foundation strips, swimming pools and tanks, terraces and balconies, in fact, for all surfaces exposed to weather impact and bending stress.

Manner of application: Surface must be dry with good load-bearing capacity, with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities. Cement surfaces, cement screeds and plaster must be at least 28 days old. Large dents and damaged elements must first be filled with KERAMOL adhesive or renovation plaster. Gradually add the content of one 12kg bag to 3.0-3.2l of water constantly mixing until a homogenous lump-free compound is achieved. Leave it for 5-10 minutes and then thoroughly mix again. Compound made in this way is ready for application and must be used within 1 hour. Before applying waterproofing coat, the surface must be wetted. Apply two coats of the prepared compound using a rigid and robust brush with cross direction procedure. Apply the second coat immediately after the first coat has hardened but which is not fully dry. With surfaces which are exposed to high water impact it could be nece-ssary to apply 3 or 4 coats. If the application time between two coats is longer than 24 hours, do light sanding of the previous coat. Minimum thickness of a single coat is 0.7mm and maximum is 2mm. Cor-ners, drains and pipe runs should be insulated using insulating tape. Walking on the insulated substrate is possible after 3 days. Ceramic tiles can be laid after 3 to 5 days depending on the coat thickness and weather conditions.

Consumption: ≈1.2kg/m²/mm depending on the roughness and absorption capacity of substrate, technique and manner of application.

HIDROMAX® FlexProperties and use: HIDROMAX Flex is a flexible 2k compound made on cement basis improved by water-repellent and waterproof polymers, specially selected aggregates and enriched by special additives. It consists of a dry A component and a liquid B component which, when mixed, create a paste-like compound applied by a brush or metal trowel. It is used for protection of buildings against rising capillary damp, penetration of water under low pressures as well as in situations where water-proofing capacity must be ensured due to positive hydrostatic pressure of water. It is recommended for waterproofing of kitchens, bathrooms, dug walls, basement and cellar premises, foundation strips, tanks, terraces and balconies.

Manner of application: Surface must be dry with good load-bearing capacity, with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities. Cement surfaces, cement screeds and plaster must be at least 28 days old. Large dents and damaged elements first must be filled with KERAMOL adhesive or renovation plaster. Gradually add the content of one 12kg bag (A component) to 5kg of liquid (B component) constantly mixing until a homogenous compound suitable for brush application is achieved. Com-pound made in this way is ready for application and must be used within 1 hour. Before applying waterproofing coat, the surface must be wetted. Apply two coats of the prepared compound using a rigid and robust brush with cross direction procedure. Apply the second coat immediately after the first coat has hardened but which is not fully dry. With surfaces which are exposed to high water impact it could be necessary to apply 3 or 4 coats. If the application time between two coats is longer than 24 hours, do light sanding of the previous coat. Minimum thickness of a single coat is 0.7mm and maximum is 2mm. Corners, drains and pipe runs should be insulated using insulating tape. Walking on the insulated substrate is possible after 3 days. Ceramic tiles can be laid after 3 to 5 days depending on the coat thickness and weather conditions.

Consumption: ≈2 kg/m²/mm depending on the roughness and absorption capacity of the substra-te, technique and manner of application.

HIDROMAX® PlusProperties and use: HIDROMAX Plus 1k is a compo-und made on basis of cement and specially selected aggregates, improved by water-repellent and waterproof polymers and additives. When mixed with water, a paste-like compound is achieved which can be applied with a brush or metal trowel. It is used for protection of cement and buildings from rising capillary damp appearance, penetration of water under low pressures as well as in situations where waterproofing capacity must be ensured due to positive hydrostatic pressure. It is recommended for waterproofing of dug walls, basement and cellar premises, foundation strips and tanks.

Manner of application: Surface must be with good load-bearing capacity, with no loose or crum-bly areas, dust, water-soluble salts, grease and other impurities. Cement surfaces, cement screeds and plaster must be at least 28 days old. Large dents and damaged elements must first be filled with KERAMOL adhesive or renovation plaster. Add the content of one HIDROMAX Plus 12kg bag to 3.2-3.5l of water and mix until a homogenous lump-free compound is achieved. Leave it for 5-10 minutes and then thoroughly mix again. Compound made in this way is ready for application and must be used within 1 hour. Before applying waterproofing coat, the surface must be wetted. Apply two coats of the prepared compound using a rigid and robust brush with cross direction procedure. Apply the second coat immediately after the first coat has hardened but which is not fully dry. With surfaces which are exposed to high water impact it could be necessary to apply 3 or 4 coats. If the application time between two coats is longer than 24 hours, do light sanding of the previous coat. Minimum thickness of a single coat is 0.7mm and maximum is 2mm. Corners, drains and pipe runs should be insulated using insulating tape. Walking on the insulated substrate is possible after 3 days. Ceramic tiles can be laid after 3 to 5 days depending on the coat thickness and weather conditions.

Consumption: ≈1.9 kg/m²/mm depending on the roughness and absorption capacity of substrate, technique and manner of application.

kg

1212kg

5+A B

kg

12kg

10

31

HIDROMAX

® 505Features and purpose: HIDROMAX 505 is an elastic two-component polymer - cement mass made on the basis of cement, selected fillers, waterproof and water-repellent polymer with the addition of an additive. It consists of dry component A and liquid component B, whose mixture creates a pasty mass that is applied with a brush. It is used to protect buildings from water wicking, penetration of water under low pressure, as well as in situations where it is necessary to provide water resistance in a positive hydrostatic pressure of water. It is recommended for waterproofing bathrooms, kitchen, ground walls, basements and fundamental premises, tanks and pools. It can be used in systems with underfloor heating.

Manner of work: The surface must be: carryable, clean and free of loose materials, dust, water-soluble salts, grease and other contaminants. Concrete surfaces, cement screeds, and mortar must be min. 28 days old. Large cavities and damaged items to be previously filled out with a patching mortar, concrete or KERAMOL adhesive for ceramic tiles. The content of one 5 kg bag (component A) is gradually added to 5 kg of liquid (component B) under continuous mixing (mixing ratio 1: 1), until a homogeneous mass is suitable for brush application. Let the mass stand 10 minutes, then stir again. Thus prepared mass is ready for installation and must be used within 1 hour. Before applying the substrate, the surface should be dampened well. The prepared mass is applied with solid and robust brush, in two coatings, in a cross-process. The second coating is applied immediately after the first layer hardens while it is not completely dry. Each subsequent layer is applied in the opposite direction so that the layers are crossed. In areas that are exposed to the strong influence of water you may need 3 or 4 coats. If the time between the application of layers is greater than 24 hours, the previous layer is to be lightly sandblasted. Min. total thickness of layers is 2 mm, and max. 5 mm. Corners, drains, and pipe penetrations must be insulated using insulating tape. It is possible to walk on isolated background after 3 days. Ceramic tiles can be laid after min. 12 hours, depending on thickness and climatic conditions.

Consumption: ≈1.2-1.4kg/m2 for two layers, depending on the roughness and absorption, and application techniques.

HIDROMAX® ElasticProperties and use: HIDROMAX Elaxtic is elastic 2k compound made on basis of cement and specially selected aggregates, improved by water repellent, waterproof and alkalyne resistant polymers, fibre re-inforced, enriched by special additives for waterpro-ofing and protection of cement surfaces. It consists of a dry A component and a liquid B component which, when mixed, create a paste-like compound applied by brush or metal trowel. It has crack-bridging properties, excellent adherence to mineral surfaces, can be applied at lower temperatures and in damp conditions. It is used for protection of buildings against rising capillary damp, penetration of water under pressure as well as in situtions where waterproofing capacity must be ensured due to positive and higher negative hydrostatic pressure. It is recommended for waterproofing of kitchens, bathrooms, dug walls, basement and cellar premi-ses, foundation strips, swimming pools, terraces and balconies, actually, for all surfaces exposed to weather impact and bending stress.

Manner of application: Surface must be dry with good load-bearing capacity, with no loose or crumbly areas, dust, water-soluble salts, grease and other impurities. Cement surfaces, cement screeds and plaster must be at least 28 days old. Large dents and damaged elements first must be filled with KERAMOL adhesive or repair plaster. Gradually add the content of one 10kg bag (A component) to 5 kg of liquid (B component) constantly mixing until a homogenous compound suitable for brush application is achieved. Compound made in this way is ready for application and must be used within 1 hour. Before applying waterproofing coat the surface must be wetted. Apply two coats of the prepared compound using a rigid and robust brush in cross direction procedure. Apply the second coat immediately after the first coat has hardened but which is not fully dry. With surfaces which are expo-sed to high water impact it could be necessary to apply 3 or 4 coats. If the application time between two coats is longer than 24 hours, do light sanding of the previous coat. Minimum thickness of a single coat is 0.7mm and maximum is 2mm. Corners, drains and pipe runs should be insulated using insulating tapes. Walking on the insulated substrate is possible after 3 days. Ceramic tiles can be laid after 3 to 5 days depending on the coat thickness and weather conditions.

Consumption: ≈1.8kg/m²/mm depending on the roughness and absorption capacity of the substrate, technique and application manner.

HIDROMAX® LFProperties and use: HIDROMAX Liquid Foil is 1k water insulation coat, based on dispersion of special polymeric binders, with carefully selected additives that enhance its water repellent and waterproof properties and specially selected aggregate fillers. The coat forms a flexible, fast-drying water-resistant membrane. It is ready-to-use and easy to apply. It is intended for exterior and interior use on horizontal and vertical surfaces such as terraces, balconies and premises exposed to occasional impact of water: kitchens, bathrooms, shower cabins, public toilets, etc. It is also used in systems with floor heating. It can be applied to: concrete, cement screeds and mortars, gypsum-cardboard panels (only in interior premises), ceramic tiles, terrazzo, stone and similar. HIDROMAX Liquid Foil is not the finishing coat and a solid protection has to be fitted over it (ceramic tiles, stone, mosaic, concrete...). The coat is harmless to people and environment.

Manner of application: Surface must be: dry, with good load-bearing capacity, clean and with no loose areas, dust, water-soluble salts, grease and other impurities. Concrete surfaces, concrete screeds and plaster must be at least 28 days old. Large dents and damaged elements must be previously filled with KERAMOL adhesive or repair plaster. It must not be applied to cement surfaces with moisture higher than 3%, to surfaces with capillary moisture absorption, gypsum mortars with moisture content higher than 1% and gypsum levelling compounds with moisture content higher than 0.5%. Smooth surfaces such as old tiles or terrazzo must be previously honed and dust removed. HIDROMAX Liquid Foil is delivered ready-to-use. It should be thoroughly mixed and must not be diluted. Apply the material with a robust brush or long-haired roller in two coats with thickness of minimum 1.0mm and maximum 1.5mm. Apply the second coat in cross direction to the first coat at least 4 hours after the first coat has been applied, i.e. after the first coat has dried and obtained a darker and mat surface. Corners, drains and pipe runs should be insulated with HIDROMAX insulation tapes which are impressed into the first coat and coated with the next one. Further processing of the treated surface, i.e. fitting of hard surfaces (ceramic tiles, stone, mosaic, concrete, etc.) is possible minimum 6 hours after the application of the second coat.

Consumption: 1.0-1.3kg/m² in two coats, depen-ding on the roughness and absorption capacity of the substrate, technique and application manner.

kg

1010kg

5+A B

kg

5kg

5+A B

kg

5|15


323232

kg

35kg

35kg

35

MAXIMAL

® CProperties and use: MAXIMAL C is a ready-made cement mortar used for machine and manual plastering of all load-bearing interior and exterior wall surfaces. It can be used with all wall types made of brick, aerated concrete elements, concrete and natural stone. It is recommended for premises with increased moisture content, sanitary facilities, basements, etc.

Manner of application: Surfaces must be dry, free of dust, grease and other impurities as well as with no loosely bonded areas. Larger uneven areas as well as holes and installation slits must be filled in advance. With brick walls having deep and wide joints, it is necessary to fill the latter before mortar is applied. Surfaces treated in such a manner must be grouted. We recommend MAXIMAL Spray for grouting smooth surfaces; another recommendation is MAXIKRIL Contact, acrylic bonding bridge. Very absorbent surfaces should be grouted with MAXICRIL Concentrate base. Apply the mortar by machine and immediately after the application use the aluminium H screed rail to roughly even the surface. After the surface is partially dry, remove the excess material. The mortar is „opened“ by aluminium T screed rail or with a special scraper. The surface remains rough after such a treatment. After the „opening“ the surface must be sprayed with water and floated by foam sanding block, thus achieving the finishing appearance. Minimum coat thickness is 1.5cm. With uneven surfaces where a thicker coat of mortar should be applied, apply the mortar again after a certain period of time but before the previous coat has bonded.

Application temperature: Optimum application temperature ranges from +5°C do +25°C. The air and surface to which mortar is applied must be in this temperature range.

Consumption: ≈16kg/m² for 10mm thickness for applying to even surfaces.


MACHINE APPLIED MORTARS

MAXIMAL

® SProperties and use: MAXIMAL S is a ready-made cement-lime mortar used for machine and manual plastering of all load-bearing exterior and interior wall surfaces. It can be used for all wall types made of brick, aerated concrete elements, concrete and natural stone.

Manner of application: Surfaces must be dry, free of dust, grease and other impurities as well as with no loosely bonded areas. Larger uneven areas as well as holes and installation slits must be filled in advance. With brick walls having deep and wide joints, it is necessary to fill the latter before mortar is applied. Surfaces treated in such a manner must be grouted. We recommend MAXIMAL Spray for grouting smooth surfaces; another recommendation is MAXIKRIL Contact, acrylic bonding bridge. Very absorbent surfaces should be grouted with MAXICRIL Concentrate base. Apply the mortar by machine and immediately after the application use the aluminium H screed rail to roughly even the surface. After the surface is partially dry, remove the excess material. The mortar is „opened“ by aluminium T screed rail or with a special scraper. The surface remains rough after such a treatment. After the „opening“ the surface must be sprayed with water and floated by foam sanding block, thus achieving the fine finishing appearance. Minimum coat thickness is 1.5cm. With uneven surfaces where a thicker coat of mortar should be applied, apply the mortar again after a certain period of time but before the previous coat has bonded.




MAXIMAL

®

Properties and use: MAXIMAL is a ready-made lime-cement mortar used for machine and manual plastering of all load-bearing interior wall surfaces. It can be used for all wall types made of brick, aerated concrete elements, concrete and natural stone.

Manner of application: Surfaces must be dry, free of dust, grease and other impurities as well as with no loosely bonded areas. Larger uneven areas as well as holes and installation slits must be filled in advance. With brick walls having deep and wide joints, it is necessary to fill the latter before mortar is applied. Surfaces treated in such a manner must be grouted. We recommend MAXIMAL Spray for grouting smooth surfaces; another recommendation is MAXIKRIL Contact, acrylic bonding bridge. Very absorbent surfaces should be grouted with MAXICRIL Concentrate base. Apply the mortar by machine and immediately after the application use the aluminium H screed rail to roughly even the surface. After the surface is partially dry, remove the excess material. The mortar is „opened“ by aluminium T screed rail or with a special scraper. The surface remains rough after such a treatment. After the „opening“ the surface must be sprayed with water and floated by foam sanding block, thus achieving the fine finishing appearance. Minimum coat thickness is 1.5cm. With uneven surfaces where a thicker coat of mortar should be applied, apply the mortar again after a certain period of time but before the previous coat has bonded.


Potrošnja: ≈14kg/m² for 10mm thickness for applying to even surfaces.


333333

kg

35kg

30

MAXIMAL

® SprayProperties and application: MAXIMAL Spray is a binding agent, binding bridge intended for machine and hand application. It is used for all plastered substrates. It is especially recommended for highly absorbent, smooth and critical substrates (concrete, brick, aerated concrete elements, mixed-material walls, natural stone substrates). Application of MAXIMAL Spray provides good plaster adhesion, uniform substrate absorption capacity and rough surface.

Manner of application: Surface must be dry, free of dust, grease and other impurities as well as of loosely bonded areas. Apply MAXIMAL Spray using cement sprayer or manually using a construction dipper. With mixed-material surfaces it is necessary to apply mesh which would prevent crack formation. Before application check if the joints are filled in line with the wall. Apply MAXIMAL Spray evenly on a dry surface. Drying time is at least 2 days.


Consumption: ≈3kg/m²


MAXIMAL

® GProperties and use: MAXIMAL G is a ready-made gypsum-lime mortar used for machine and manual plastering of all load-bearing interior wall surfaces. It can be used for all wall types made of brick, aerated concrete elements, concrete and natural stone.

Manner of application: Surfaces must be dry, free of dust, grease and other impurities as well as with no loosely bonded areas. With brick walls having deep and wide joints, it is necessary to fill the latter before mortar is applied. Surfaces treated in such a manner must be grouted. For impregnation of smooth concrete surfaces use MAXIKRIL Contact, acrylic bonding bridge. Grout very absorbent surfaces with MAXIKRIL Concentrate base. Apply the mortar by machine and immediately after the application use the aluminium H screed rail. After the coat is partially dry, the surface must be „felted“. In this manner the mortar is finally distributed and levelled. After „felting“ the surface is treated with a butterfly trowel, skimmed, to achieve the fine, smooth, finishing appearance. Minimum coat thickness is 8mm. For uneven surfaces where a thicker coat of mortar should be applied, apply the mortar twice. The first coat should be sprayed and combed to remain rough, then wait to harden and dry and after that apply the second coat. After spraying the surface, empty the hose, pump and mixer. Do not mix with other materials!




34

Panel thickness Panel length x width

Panels per bundle (pcs.)

Panel surface area with straight

edges per bundle (m²)

Volume of panels with straight

edge per bundle (m3)

Surface area of panels with

shiplap edge (m²)

Volume of panels with shiplap edge

per bundle (m3)

10 mm

1000 mm x 500 mm

50 25 0.25 - -

20 mm 25 12.5 0.25 - -

30 mm 0.2416 8 - -

40 mm 0.2412 6 5.733 0.229

50 mm 10 5 0.25 4.777 0.239

60 mm 8 4 0.24 3.822 0.229

70 mm 7 3.5 0.245 3.344 0.234

80 mm 6 3 0.24 2.866 0.229

100 mm 5 2.5 0.25 2.389 0.239

110 mm 4 2 0.22 1.911 0.21

120 mm 4 2 0.24 1.911 0.229

140 mm 4 2 0.28 1.911 0.268

150 mm 3 1.5 0.225 1.433 0.215

160 mm 3 1.5 0.24 1.433 0.229

180 mm 3 1.5 0.27 1.433 0.258

190 mm 3 1.5 0.285 1.433 0.272

200 mm 3 1.5 0.3 1.433 0.287

210 mm 2 1 0.21 0.955 0.201

220 mm 2 1 0.22 0.955 0.21

230 mm 2 1 0.23 0.955 0.22

240 mm 2 1 0.24 0.955 0.229

250 mm 2 1 0.25 0.955 0.239

260 mm 2 1 0.26 0.955 0.248

270 mm 2 1 0.27 0.955 0.258

280 mm 2 1 0.28 0.955 0.268

300 mm 2 1 0.3 0.955 0.287

Styrofoam typeHarmonised

technical speci�cation

Colour on bundle Thermal conductivity coe�cient (λ) Fireproof grade Compressive

strength

M30

EN 13163

blue line 0.047 W/(m·K)

European class „E“ in accordance

with regulation EN 13501-1

min. 30 kPa

MF60 two red lines 0.042 W/mK min. 60 kPa

MF red line 0.039 W/mK min. 80 kPa

M90 green line 0.039 W/mK min. 90 kPa

M100 yellow line 0.038 W/mK min. 100 kPa

M120 black line 0.036 W/mK min. 120 kPa

M150 two black lines 0.034 W/mK min. 150 kPa

M200 purple line 0.033 W/mK min. 200 kPa

The stated panel surface area refers to the panel adhesion area.

35

Upon request, panels can be produced in other sizes, maximum up to 4000mm x 1000mm.Panels can be produced in all thickness dimensions from 10 to 300mm, as long as the panel thickness is rounded to 10mm.

Shear strength Tensile strength Panel length x width Panel thicknessSurface area of

panels with straight edge

Surface area of panels with shiplap

edge

min. 70 kPa min. 60 kPa

1000 x 500 mm from 10 to 300 mm 0.5 m² 0.4777 m²








WA

LL

Insu

latio

n of

fa

çade

sur

face

s

Insu

latio

n of

in

teri

or s

urfa

ces

Insu

latio

n in

“s

andw

ich”

wal

ls

Rain

scre

en

faça

de

Expa

nsio

n jo

int

SLA

B

Roof

sla

b

Susp

ende

d sl

ab

Gro

und

leve

l sla

b

Abo

ve-b

asem

ent

slab

Abo

ve-p

assa

ge

slab

ROO

F

Flat

roof

Pitc

hed

roof

- ab

ove

raft

ers

Pitc

hed

roof

- am

ong

raft

ers

Maxitherm M30 x x x x

Maxitherm MF60 x* x x x x x x

Maxitherm MF x x x x x

Maxitherm M90 x x x x x


Maxitherm M120 x x x x



*MAXIMA does not recommend this product for installation in MAXITHERM facade systems.

STYROFOAM

36

kg

25

kg

25

kg

25

DECORATIVE FACADE RENDERS

37

ROLOCEM®

Properties and use: ROLOCEM is a cement-lime dry type of render used for protection and de-coration of exterior and interior wall surfaces as well as the finishing coat for thermal insulation facades. It can be applied to asbestos cement, gypsum-cardboard panels and chipboards. It has good adherence to the substrate, water vapour permeability, strength and stability in different climate areas. It is resistant to weather and UV rays.

Manner of application: Surface must be flat, dry, firm, with no loose and crumbly areas, dust, water-soluble salts, grease and other impurities which may prevent good adherence to the substrate. Leave the rendered surfaces to dry for 28 days and the finishing coat of adhesive and reinforcement mortar for 7 days. Prior to

application, surface must be grouted. With newly rendered surfaces and surfaces with lower load-bearing capacity, walls must be first impregnated by MAXIKRIL Hidrosol base. When MAXIKRIL Hidrosol is dry, apply ROLOGRUND. Add 25kg of ROLOCEM to 5.0-5.5l of water and mix well to achieve a homogenous, lump-free mixture, but not to long to avoid formation of foam which may cause problems in application. In case this happens, leave the mixture for 15-20 minutes and apply then. Use up the prepared mixture within 2 hours. Apply ROLOCEM after the primer is fully dry using a steel or plastic trowel and do the finishing treatment with a flat plastic trowel. Paint the surfaces treated with ROLOCEM after 3 weeks of ROLOCEM application at earliest. After application, immediately rinse the tools with water.

Application temperature: Optimum applicati-

on temperature ranges from +10°C do +30°C. It must not be used below +5°C as well as in bright sunshine, wind, fog and rain. Protect the newly coated surfaces, in optimum conditions, from the weather impact for at least 24 hours.

Shelf life and storage: 6 months from the date of production stated on the packaging. Keep in the sealed and undamaged packaging in dry and well aerated premises.

COLORPLAST®

Properties and use: COLORPLAST is a high-qu-ality decorative mosaic on basis of acrylates and marble grains with 2mm particle size. It is dis-tinguished by good adherence to the substrate and high strength. It is stable against the impact of weather and UV rays. It is used for protection and decoration of exterior and interior mineral wall surfaces. It represents the finishing coat for thermal insulation facades.

Manner of application: Surface must be flat, dry, firm, with no loose and crumbly areas, dust, water-soluble salts, grease and other impurities which could prevent good adherence to the su-bstrate. Leave the rendered surfaces to dry for 28 days and the finishing coat of adhesive and rein-forcement mortar for 7 days. Prior to application, surface must be grouted. With newly rendered surfaces and surfaces with lower load-bearing

capacity, walls must be impregnated by MAXI-KRIL Hidrosol base. When MAXIKRIL Hidrosol is dry, apply ROLOGRUND in a shade approximate to the shade of the render finish which prevents shadow appearance. Before application mix COLORPLAST until the initial foam appears and then it is ready to use. Avoid long and intensive mixing. In case a larger amount of foam appears, leave the can for 24 hours so that the excess air is released and only after that start the applicati-on. COLORPLAST OF DIFFERENT BATCHES AND DATES OF PRODUCTION MUST ALWAYS BE HO-MOGENISED! To conduct homogenisation, take a larger container and mix the content of several pails in it. When the homogenised amount of approximately one pail is used up, add the new one and mix. Render finish is applied after the primer is fully dry. Apply the 3mm thick coat with the steel broad knife. Remove the excess ma-terial with the steel broad knife and smooth it, paying attention not to leave any space among

the grains. When cleaning the broad knife and trowel and returning the material to the can, occasionally homogenise the returned material in order to avoid excess binder appearance in the finishing film. After application, immediately rinse the tools with water.

Application temperature: Optimum application temperature ranges from +10°C do +30°C. It must not be used below +5°C as well as in bright sunshine, wind, fog and rain. Protect the newly coated surfaces, in optimum conditions, from the weather impact for at least 24 hours.

Consumption: 4.5kg/m² on average for 3mm coat thickness.


ROLOAKRIL®

Properties and use: ROLOAKRIL is a high-quality decorative render based on acrylates. It is distinguished by high strength and water repellence. It provides good adherence to substrate and water vapour permeability. It is stable against the impact of weather and UV rays. It is used for protection and decoration of exterior and interior mineral wall surfaces. It represents the finishing coat for thermal insulation facades. It is available in white shade and can be tinted in MAXIMIX system in shades with F designation.

Manner of application: Surface must be flat, dry, firm, with no loose and crumbly areas, dust, water-soluble salts, grease and other impurities which may prevent good adherence to the substrate. Leave the rendered surfaces to dry

for 28 days and the finishing coat of adhesive and reinforcement mortar for 7 days. With newly rendered surfaces and surfaces with lower load-bearing capacity, walls must be first impregnated by MAXIKRIL Hidrosol base. When MAXIKRIL Hidrosol is dry, apply ROLOGRUND tinted in a shade approximate to the shade of the render finish. Before application stir ROLOAKRIL and it is ready to use. ROLOAKRIL TINTED IN MAXIMIX SYSTEM OR ROLOAKRIL OF DIFFERENT BATCHES AND DATES OF PRODUCTION MUST ALWAYS BE HOMOGENISED! To conduct homogenisation, take a larger container and mix the content of several pails in it. When the homogenised amount of approximately one pail is used up, add the new one and mix. Render finish is applied after the primer is fully dry. Apply with steel or plastic broad knife and do the finishing treatment with a flat plastic broad knife. After application, immediately rinse the tools with water.



Consumption

1.5 mm 2.0 mm

Scraped ≈2.4 kg/m² ≈2.7 kg/m²

Smoothed ≈2.6 kg/m² ≈3.3 kg/m²

Consumption

1.5 mm 2.0 mm

Scraped ≈2.5 kg/m² ≈3.1 kg/m²


38

kg

25

kg

25

kg

25

DECORATIVE FACADE RENDERS

39

ROLOSIL® SNProperties and use: ROLOSIL SN is a high-quality decorative render on silicone basis. It is distinguished by high strength and good water vapour permeability. It has good adherence to substrate and provides long-term and high water repellence. It is stable against weather and UV rays. It is used for protection and decoration of exterior and interior mineral wall surfaces. It represents the finishing coat for thermal insulation facades. It is available in white shade and can be tinted in MAXIMIX system in shades with ST designation.

Manner of application: Surface must be flat, dry, firm, with no loose and crumbly areas, dust, water-soluble salts, grease and other impurities which may prevent good adherence to the sub-strate. Leave the rendered surfaces to dry for 28 days and the finishing coat of adhesive and rein-

forcement mortar for 7 days. Prior to application, surface must be grouted with ROLOGRUND SN, coarse silicone primer coating tinted in a shade approximate to the shade of render finish. Befo-re application stir ROLOSIN SN and it is ready to use. ROLOSIL SN TINTED IN MAXIMIX SYSTEM OR ROLOSIL SN OF DIFFERENT BATCHES AND DATES OF PRODUCTION MUST ALWAYS BE HOMO-GENISED! To conduct homogenisation, take a larger container and mix the content of several pails in it. When the homogenised amount of approximately one pail is used up, add the new one and mix. Render finish is applied after the primer is fully dry. Apply with steel or plastic trowel and do the finishing treatment with a flat plastic trowel. After application, immediately rinse the tools with water.

Application temperature: Optimum application temperature ranges from +10°C do +30°C. It must not be used below +5°C as well as in

bright sunshine, wind, fog and rain. Protect the newly coated surfaces, in optimum conditions, from the weather impact for at least 24 hours.


ROLOSIL® STProperties and use: ROLOSIL ST is a high-quality decorative render on silicate basis. It is distinguished by high strength and water vapour permeability. It is stable against weather and UV rays. It has good adherence to substrate and cannot burn. It is used for protection and decoration of exterior and interior mineral wall surfaces. It represents the finishing coat for thermal insulation facades. It is available in white shade and can be tinted in MAXIMIX system in shades with ST designation.

Manner of application: Surface must be flat, dry, firm, with no loose and crumbly areas, dust, water-soluble salts, grease and other impurities which may prevent good adherence to the substrate. Leave the rendered surfaces to dry for 28 days and the finishing coat of adhesive and reinforcement mortar for 7 days. Prior to

application, surface must be grouted with ROLOGRUND ST, coarse silicone primer coating tinted in a shade approximate to the shade of render finish. Before application stir ROLOSIL ST and it is ready to use. ROLOSIL ST TINTED IN MAXIMIX SYSTEM OR ROLOSIL ST OF DIFFERENT BATCHES AND DATES OF PRODUCTION MUST ALWAYS BE HOMOGENISED! To conduct homogenisation, take a larger container and mix the content of several pails in it. When the homogenised amount of approximately one pail is used up, add the new one and mix. Render is applied after the primer is fully dry. Apply with a steel or plastic trowel and do the finishing treatment with a flat plastic trowel. After application, immediately rinse the tools with water.

Application temperature: Optimum application temperature ranges from +10°C do +25°C. It must not be used below +8°C as well as in

bright sunshine, wind, fog and rain. Protect the newly coated surfaces, in optimum conditions, from the weather impact for at least 48 hours.


NANOTEX®

Properties and use: NANOTEX is a high-quality decorative render based on composite binders. It is distinguished by excellent adherence to the substrate, high water vapour permeability, strength, dirt resistance and distinctive water repellence. It is resistant to the weather condi-tions and UV rays. It is used for protection and decoration of exterior and interior mineral wall surfaces. It represents finishing coat for thermal insulation facades. It is available in white shade and can be tinted in MAXIMIX system in shades with F designation.

Manner of application: Surface must be flat, dry, firm, with no loose and crumbly areas, dust, water-soluble salts, grease and other impurities which may prevent good adherence to the substrate. Leave the rendered surfaces to dry for 28 days and the finishing coat of adhesive

and reinforcement mortar for 7 days. Prior to application, surface must be grouted. With newly rendered surfaces and surfaces with lower load-bearing capacity, walls must be first impregnated by MAXIKRIL Hidrosol base. When MAXIKRIL Hidrosol is dry, apply ROLOGRUND tin-ted in a shade approximate to the shade of the render finish or ROLOGRUND ST if stone wool is used for thermal insulation. Before application mix NANOTEX and it is ready to use. NANOTEX TINTED IN MAXIMIX SYSTEM OR NANOTEX OF DIFFERENT BATCHES AND DATES OF PRODUC-TION MUST ALWAYS BE HOMOGENISED! To conduct homogenisation, take a larger container and mix the content of several pails in it. When the homogenised amount of approximately one pail is used up, add the new one and mix. Render finish is applied after the primer is fully dry. Apply with steel or plastic trowel and do the finishing treatment with a flat plastic trowel.

After application, immediately rinse the tools with water.



Consumption

1.5 mm 2.0 mm

Scraped ≈2.4 kg/m² ≈2.7kg/m²


Consumption

1.5 mm 2.0 mm



Consumption

1.5 mm 2.0 mm



404040

kg

25kg

25kg

25

ADHESIVES FOR THERMAL INSULATION SYSTEMS

STIROMOL® BazniProperties and use: STIROMOL Bazni is a one-part dry type of construction adhesive, made of hydraulic and synthetic binders, used for bonding Styrofoam to mineral surfaces.

Manner of application: Add a 25kg bag of STIROMOL Bazni to 5.5-6l of water and mix until a homogenous, lump-free compound is achieved. Leave it for 10 minutes and then thoroughly mix again. Compound made in such a manner is ready to apply and must be used within 2 hours. Apply STIROMOL Bazni to thermal insulation panels (adhesive surface coverage must be at least 40%), then bond the panels by pressing to a firm and clean substrate. Applying anchor bolts is recommended after 2-3 days to the bonded Styrofoam panels (6 pcs./m²).

Warning: STIROMOL Bazni is be used only for bonding Styrofoam panels. This product is not intended for reinforcing mesh or a finishing coat.


Consumption: From 3.5kg/m², depending on the wall surface.


STIROMOL® ThermoProperties and use: STIROMOL Thermo is a one-part, elastic, dry type of construction adhesive, made of hydraulic and synthetic binders with additives. It is used for bonding Styrofoam to all types of mineral surfaces as well as to the reinforcing coat on EPS panels.

Manner of application: Add a 25kg bag of STIROMOL Thermo to 6-6.5l of water and mix until a homogenous, lump-free compound is achieved. Leave it for 10 minutes and then thoroughly mix again. Compound made in such a manner is ready to apply and must be used within 2 hours. Apply STIROMOL Thermo to thermal insulation panels along the edges and on 3-6 spots in the middle of the panel (adhesive surface coverage must be at least 40%) then bond the panels by pressing them to a solid and clean substrate. Applying anchor bolts is recommended after 2-3 days to the bonded thermal insulation panels (6 pcs./m²). Apply reinforcing mesh by slightly pushing it into the coat of applied STIROMOL Thermo, 2-3mm of thickness, with overlap of min. 10cm and then level the whole surface with STIROMOL Thermo adhesive. The total thickness of applied STIROMOL Thermo should be at least 4mm.


Consumption: From 3.5-5kg/m² for bonding | from 4-5kg/m² for reinforcing.


STIROMOL® ElasticApplication and use: STIROMOL Elastic is a two-part, highly elastic, dry type of construction adhesive made of hydraulic and synthetic binders with special additives. It is used or bonding and reinforcing thermal insulation panels: Styrofoam, thermoseal, Styrodur and stone wool to all types of mineral surfaces.

Manner of application: Add 25kg of STIROMOL Elastic to 6-6.5l of water and mix until a homo-genous, lump-free compound is achieved. Leave it for 10 minutes and then thoroughly mix again. Compound made in such a manner is ready to apply and must be used within 2 hours. Apply STIROMOL Elastic to thermal insulation panels along the edges and on 3-6 spots in the middle of the panel (adhesive surface coverage must be at least 40%). If stone wool panels are used, apply adhesive to the whole surface of the panels using a notched trowel. Bond the panels by pressing them to a solid and clean substrate. Applying anchor bolts is recommended after 2-3 days to the bonded thermal insulation panels (6 pcs./m²). Apply reinforcing mesh by slightly pushing it into the coat of applied STIROMOL Elastic, 2-3mm of thickness, with overlap of min. 10cm and then level the whole surface with STIROMOL Elastic. The total thickness of applied STIROMOL Elastic should be at least 4mm.


Consumption: From 3.5kg/m² for bonding | from 4-5kg/m² (EPS); 6-7kg/m² (MV) for reinforcing.


414141

1

2

3

4

5

a

b

c

123

STIROMOL Thermoadhesive for Styrofoam bonding and reinforcing

123

STIROMOL Elastic adhesive for stone wool, EPS boards, graphite Styrofoam, Styrodur and reinforcing mesh

4 ROLOGRUNDcoarse acrylicfoundation coat

5 ROLOAKRILacrylic decorativerender

ROLOGRUND SNcoarse siliconefoundation coat

ROLOSIL SNsilicone decorativerender

ROLOGRUNDcoarse acrylicfoundation coat

NANOTEXnano-silicatedecorative render

a thermal insulation products b glass fibre mesh c anchor bolt

MAXITHERM STANDARDfacade thermal insulation system with EPS

MAXITHERM® StandardMAXITHERM Standard represents a traditional ETICS system with Styrofoam (EPS-expanded polystyrene). It is used for installation of thermal insulation systems on new and old buildings. It can be used in all building where you wish to achieve energy saving with reliable and high-quality ETICS system at an attractive price.

Properties: reliable thermal insulation; additional protection against algae and fungus; high dirt resistance; water vapour permeable and water repellent; resistant to weather impact and UV rays; shade intensity does not fade with time; extremely wide range of shades.

424242

a a

1 12 23 34 45 5

b bc c

123

STIROMOL Elasticadhesive for stone wool, EPS boards, graphite Styrofoam, Styrodur and reinforcing mesh

4 ROLOGRUNDcoarse acrylicfoundation coat

5 ROLOAKRILacrylic decorativerender





123


4 ROLOGRUND STcoarse silicatefoundation coat

5 ROLOSIL STsilicate decorativerender

ROLOGRUND SNcoarse silicone foundation coat


ROLOGRUND STcoarse silicatefoundation coat



MAXITHERM SUPERfacade thermal insulation system with graphite EPS

MAXITHERM PREMIUMfacade thermal insulation system with mineral wool

MAXITHERMTHERMALINSULATIONSYSTEMS

MAXITHERM® SuperMAXITHERM Super represents the new generation ETICS system with Neopor-expanded polystyrene with addition of graphite. Styrofoam (EPS) with addition of graphite, due to its lower thermal conductivity coefficient, achieves the same effect of thermal insulation with 20% lower thickness compared to the equivalent „white“ expanded polystyrene.

Properties: excellent thermal insulation; additional protection against algae and fungus; high dirt resistance; water vapour permeable and water repellent; resistant to weather impact and UV rays; shade intensity does not fade with time; extremely wide range of shades.

MAXITHERM® PremiumMAXITHERM Premium represents top quality ETICS system with stone wool. This system is distinguished by its top thermal insulation and soun-dproofing properties for buildings and high water vapour permeability. Since stone wool does not burn, installing MAXITHERM Premium façade system provides additional safety in case of fire.

Properties: excellent thermal insulation and soundproofing; additional protection against algae and fungus; high dirt resistance; high water vapour permeability and water repellence; resistant to weather impact and UV rays; shade intensity does not fade with time; extremely wide range of shades.

1

2

3

4

5

a

b

c

43

123


4 ROLOGRUNDcoarse acrylic foundation coat

5 COLORPLASTacrylic marble mosaic




ROLOAKRILacrylic decorativerender


MAXITHERM STRONGfacade thermal insulation system with XPS

MAXITHERM® StrongMAXITHERM Strong represents an ETICS system with Styrodur (XPS-extruded polystyrene). It provides high resistance to mechanical load, waterproofing and thermal insulation. Due to its strength and waterproofing qualities, installing MAXITHERM Strong is recommended for house plinths.

Properties: reliable thermal insulation; additional protection against algae and fungus; high dirt resistance; high water vapour permeability and water repellence; resistant to weather impact and UV rays; shade intensity does not fade with time; extremely wide range of shades.

44

MAXIMA d.o.o. Dragise Misovica 16, 32 240 Lučani, Serbia Tel +381 (0)32 820 030 Fax +381 (0)32 817 029 Em [email protected] [email protected] www.maximapaints.rs

DISTRIBUTIVE CENTER BELGRADE Obrenovacki drum 25, 11 000 Belgrade Em [email protected] +381 (0)11 357 20 49 Tel/Fax +381 (0)11 355 13 66

DISTRIBUTIVE CENTER NIŠ Starine Novaka 7, 18 000 Niš Em [email protected] Tel/Fax +381 (0)18 42 62 693

Documents

PRODUCT CATALOGCATALOG...Company has the production capacity of 1000 tons of finished products a day with the product portfolio offering solutions for all kinds of finishing works