Products forprinted circuitsand prototypes

2

PCB Equipments

3

PCB Equipments

PCB Equipments

Shears CUTTPCB - PCB shear/blade Light boxes 34-09 - Lightboxes and fluorescent tube Drill 34-7500 - Mini drill press bench 34-10000 - Sensitive drill 34-33000 - Sensitive drill 34-30001 - Drill bits for PCB UV exposure units CI-BMG10 - UV exposure unit with timer CI-BMG40 - UV exposure unit CI-BMG100 - UV exposure unit single face CI-BMG212 - UV exposure unit double face Etching machines CI-MIN001 - PCB etch tank CI-MIN100 - PCB etch tank CI-MIN300 - PCB etch tank Other ICS-312 - Roller Tinning Machine ICB-250 -Dry Film Sheet Laminators ICF-310 - For Drilling and Isolation Routing ICR-400 - General Purpose Ovens ICA-150 - Water Treatment ICM-500 - Through-hole-planting line PCB laminates 34-01 - Photo etch pcb 34-02 - Economy photo etch PCB 34-03 - Plain copper-clad fibreglass circuit board 34-04 - Hard paper board CU 35 µm single sided 1.5mm 34-05 - Epoxy PCB 1.6mm grid pitch 2.54mm Consumable 34-30002 - Etch resist pen 34-10 - Electronics solder wire 34-105 - Solder grease 34-08 - Etch-resist transfers 34-0500 - PCB developer 34-0501 - Etch resist stripper 34-0502 - Ferric chloride etchant Accessory 34-0748 - Processing tray 34-071 - Universal PCB holder 34-072 - Universal PCB holder 34-073 - PCB holder 34-10002 - Desoldering suction pump 34-10003 - Solder iron stand 34-10000 - Solder dispenser 34-10001 - Soldering stand with magnifier 34-0601 - Rubber Gloves 34-0602 - Laboratory Coat 34-0603 - Squall Eyeshield 34-0604 - Scrub Block

Introduction

Wide range of equipment for

PCB etching and PCB production – the process of

applying a copper sheet onto the non-conductive substrate

in order to protect the PCB and create conductive

pathways or tracks between the electronic components.

PCB products include photo-etch copper clad boards,

prototyping boards for the etching of prototype PCBs, etching accessories such as

etch resist pens, lightboxes, stripboard cutters, ferric

chloride solution, etching tanks and spray processing

tanks.

4

PCB Equipments

CUTTPCB PCB Shear/Blade

Powerful, cost effective shears which have the ability to accurately cut PCB laminates, plastics up to 2mm thick and aluminium up to 1.5mm. Access to the cutting area is prevented by heavy perspex shielding extending along both sides of the blade. A safety latch is fitted to the pivot to prevent accidental operation. For positional accuracy the cutting bed is fitted with a metric rule which is recessed to assist in securing the PCB or sheeting whilst cutting. The smaller unit has a cutting capacity of 203mm (8in.) for normal 1.6mm PCB laminate and is extremely compact with an overall height of only 575mm and a base of 275 x 140mm. The larger shear will cut 1.6mm PCB laminates up to 305mm (12in.) wide and has a height of 670mm and a base of 430 x 135mm. Replacement blade sets are available separately.

Description Code

PCB Shear 8" 200mm PCB Shear CUTTPCB-200 PCB Shear 12" 300mm PCB Shear CUTTPCB-300

34-09 Lightboxes and Fluorescent Tube

These high quality lightboxes provide a valuable aid for all artwork preparation.

Provides an even illumination over the whole viewing area

Cool white fluorescent tubes are mounted below a perspex diffuser and protected by a toughened glass working surface

Robust mild steel construction

Attractive two-tone tough grey epoxy paint finish

Louvres on all sides to ensure natural air flow

Available in A4, A3 and A2 sizes

The A3 and A2 versions have an on/off switch which also selects one/two tube operation. They also have a tilt facility, which adjusts the viewing angle

Supplied with 2m UK/ICE mains lead

Replacement tubes are available separately

Size Viewing area Tubes code

A4 230 x 380mm 2x 8W, 300mm 34-0960 A3 300 x 488mm 2x 15W, 450mm 34-0962 A2 433 x 600mm 2x 20W, 600mm 34-0964

5

PCB Equipments

34-7500 Mini Drill Press Bench

Technical specifications

Rated Voltage 220V Max. Drilling Diameter 6.5mm Frequency 50Hz No-Load Speed 7500rpm Rated Input Power 180W ~

34-10000 Sensitive Drill Sensitive drill for all repetitive drilling operations in a fixed position. No transmission belt - the motor is located in the shaft of the machine. Connected to an electronic control, the rotation speed can be modified whilst maintaining a constant torque. The lowering handle can be fitted to the left or the right. Lowers using a rack assembly. The shaft is mounted on two precision ball bearings. Adjustable depth stop.

Technical specifications

Operating voltage 230 V Rotation speed 2000 → 15,000 rpm Work table dimensions (mm) 250 x 126 Shaft travel 25mm Chuck capacity 0.3 → 3.5 mm Maximum height under shaft 140 mm Max. diameter drilling - wood: 6 mm

- aluminium: 4 mm - mild steel: 2 mm

34-33000 Sensitive Drill

Technical specifications

Rated power input 125 W Electrical Supply 230 V -50/60Hz Capacity Ø 0.8 to 3.2 mm Max. drilling capacity 115 mm Working table 150 x 150 mm Clamping chuck Ø 0.5 à 3.2 mm Spindle travel 260 mm Adjustable rotation speed 10.000 - 33.000 rpm

6

PCB Equipments

34-30001 Drill Bits for PCB

Set of drill bits for PCB from 0.5 to 2mm.

CI-BMG10 UV Exposure Unit with Timer

An ultraviolet exposure unit for use in the preparation of photo resist circuit boards.

1:1 artwork, consisting of opaque transfers on translucent drafting film, is placed on the glass screen and the photo-sensitive material is placed on top

Lid incorporates a foam pad which exerts an even pressure to hold the artwork and photo board in close contact when closed

Exposure starts automatically when the six minute mechanical timer is rotated to the correct expose time

Exposure area 240 x 165mm

Incorporates two 8W actinic UV tubes, mains on/off switch and indicator, mains cable and 13A plug

CI-BMG40 UV Exposure Unit Ultraviolet (UV) Exposure Unit for exposure of photosensitive materials is designed specifically for the electronic industry, enables the realization of prototypes or small series of printed circuit boards with the method of photo-etching in a very short time. Suitable for any kind of photosensitive coating or already presensitized plates, it also allows you to obtain from the respective positive negative master or vice versa. It is also possible to print double-sided circuits, exposing first one side and then the other side. The exposure occurs through two 8W ultraviolet light tubes located above; and this facilitates the placement of master on the circuit. The pressure system in soft rubber cushion guarantees a perfect adherence of the master to the circuit. It is a very reliable machine, built entirely of metal with epoxy.

Technical characteristics

External dimensions 310 x 430 x 100mm Exposure working surface 160 x 280mm Electromechanical Timer from 0 to 15 min. Exposure Through two 8W UV light tubes Voltage 220 V 50/60 Hz Power consumption 40 W Weight 8 Kg

7

PCB Equipments

CI-BMG100 UV Exposure Unit Single Face

UV exposure unit single face with drawer for a smaller footprint. Rack in steel plate and epoxy. This UV exposure unit is equipped with a vacuum pump, which can be viewed on the vacuum gauge. Ensuring the best results, the photoengraving is done through four 15 W UV light lamps with fast reactors. The digital timer allows programming from 0 to 999 seconds.

Technical characteristics

External dimensions 485 x 600 x 160mm Working surface 255 x 385mm Electromechanical Timer From 0 to 15 min Digital Timer 3 digits Vacuum control Via vacuum gauge Exposure Area Homogeneous Exposure Through four 15W UV light tubes Voltage 220 V Power consumption 130 W Weight 28 Kg

CI-BMG212 UV Exposure Unit Double Face

UV exposure unit double faces with vacuum pump for exposure of photosensitive materials Designed for double-sided printed circuit board with method of photoengraving, can also be used as a UV exposure unit single face excluding the lower ramp of lamps with a special button in the control panel. Upper and lower floor in soft transparent material, particularly ultraviolet resistant. This ensures an equal exposition on both sides. Vacuum control via front panel place meter commands. Is possible memorize up to 32 exposure times, that remain in memory even in absence of power supply. All functions are easily settable from keyboard and are displayed by means 4 displays.

Technical characteristics

External dimensions 635 x 600 x 290mm Working surface 500 x 375mm Exposure Area Homogeneous Exposure Through twelve 20W UV light tubes Voltage 220 V Power consumption 400 W Weight 37 Kg

8

PCB Equipments

CI-MIN001 PCB Etch tank

The etch tank are suitable for etching single and double sided PCBs with most etchants. The thin, vertical standing, design uses minimal etchant. The tanks have graduations for easy measurement. The tank can etch a maximum PCB size of 23 × 30cm without heater, or 20 × 30cm with heater. Use with 2000cc minimum, 2300cc maximum liquid. (1000cc = 1 litre) Etch tank include three clips to suspend the PCB in the liquid etchant, and a thermometer to monitor liquid temperature. Options include an air pump to bubble agitate the etchant, and heater to maintain optimal etchant temperature, for more efficient etching. The etch kits include etch tank, air pump, heater and thermometer.

CI-MIN100 PCB Etch tank

Accepts boards up to 220 x 280mm

The inside tank has a built-in heater and thermostat

Rigid outer moulded protective case

Splash-proof lid

Mesh board holder

Etchant capacity 2 litres

A pump forces air through two bubble bars to provide agitation for efficient and even etching

Splash-proof switches control mains power and the pump

Temperature is set by adjusting the thermostat control

The use of an RCD safety cut-out is recommended with this equipment

CI-MIN300 PCB Etch tank

Accepts boards up to 400 x 500mm

The inside tank has a built-in heater and thermostat

Rigid outer moulded protective case

Splash-proof lid

Mesh board holder

Etchant capacity 9 litres

A pump forces air through two bubble bars to provide agitation for efficient and even etching

Splash-proof switches control mains power and the pump

Temperature is set by adjusting the thermostat control

The use of an RCD safety cut-out is recommended with this equipment

9

PCB Equipments

ICS-312 Roller Tinning Machine Bench mounting roller tinning machine with 12" roller width. The solder tank is constructed from high grade stainless steel, suspended from a linkage mechanism. This allows it to be lowered easily from the coating roller for access and general maintenance. The two 1200 watt heaters ensure a fast heat up time, while the electronic temperature control system ensures that operating temperatures are accurately maintained. The top pressure roller can be raised and lowered by a single lever eccentric mechanism which enables it to be returned to the pre-set position without the need for resetting. Additional features include digital temperature display, thumb wheel temperature setting and motor/temperature interlock to prevent the motor being switched on while the solder is solid. The machines are fitted with stainless steel covers which provide complete protection for the operator but allow quick and easy access to the tank for replenishing salts and solder.

Specifications

Max board width 305mm (12") Max board thickness 12mm Solder bath capacity 12kg Heat up time (ambient to 240°C) 20 mins (approx) temperature control +/- 2°C Throughput speed 0-10 metres/min Electrics 220-240V, 50Hz 1ph

ICB-250 Dry Film Sheet Laminators For smaller volume production these Hot Roll Laminators enable the user to apply Dry Film Photo-Resist sheets to a wide range of materials, such as Copper PCB Laminates, Stainless Steel and Brass etc. For ‘one-off’ or very small scale production they offer an economical alternative to the Roll Laminators below. One side is laminated at a time to a thickness of 3mm thick. All temperature and speed controls are microprocessor controlled with a pre-set condition which can be manually overridden. Temperature and speed number (1-6) are indicated on the LCD display. Cold lamination is also possible.

10

PCB Equipments

ICF-310 For Drilling and Isolation Routing The ICF-310 is the smallest in a range of CNC machines for drilling and routing of PCBs and other materials. All our CNC units can be used for 'Isolation Routing' where the unwanted copper to produce a PCB is removed mechanically rather than chemically etched. The ICF-310 is the smallest and most affordable unit but it still has a processing area of 270mm x 320mm. All CNC machines are complete with drill and profile routing software. For Isolation Routing the IsoCam or IsoCam Pro software is also needed. This special piece of software uses the data from the GERBER files to generate the corresponding outline shape. Click here for a comparison table of the differences between IsoCam and IsoCam Pro. You can also get more information on IsoCam from our downloads page. All the CNC machines include a Kavo high frequency spindle (60,000 rpm) and software controlled Z-Axis for optimum processing. All machines accept industry standard tools. Floor standing or bench top enclosures are available the larger of which has an inbuilt storage cabinet and lockable wheels. Special Features :

Rigid and flat construction with low moving weights and high quality bearings for high-speed positioning.

Machine bed with universal fixture system, suitable for both clamps and ref. Pins.

KaVo high speed , 60,000 rpm spindle motor, 150 W, including 1/8" (3.175 mm) chuck.

Heavy duty stepper motor on Z-axis for true milling capability and correct tool speed.

Standard travel area: 320 x 270 x 30 mm, Sizes (mechanics) approx:70 x 55 x 30 cm3 (W x D x H)

Easy semi-automatic tool change, simultaneously 15 out of 99 tools per job.

Smallest drill diameter: 0.3mm. Drill speed: 5 hits/s (= 18 000 holes per hour)

Integral depth limiting device for (isolation) milling and engraving on uneven surfaces

Driver software for Excellon, Sieb & Meyer or HP/GL data

All machine parameters software controlled and configurable, including Z axis

Step definition: 1 mil (= 0,0254 mm), precision +/- 1 step.

Maximum speed per axis: 93 mm/s (= 5.6 m/min)

Sizes (mechanics) approx: 70 x 55 x 30 cm3 (W x D x H)

Required desktop size: approx. 80 x 80 cm. Weight: approx. 23 kg

11

PCB Equipments

ICR-400 General Purpose Ovens The exteriors of ovens are constructed from sheet steel finished in an easy clean powder coat paint. The interior chamber is stainless steel. Each oven is fitted with fixed shelf runners and removable chrome plated wire grid shelves. The top vent is fitted with a clip to hold a mercury in glass thermometer. The ovens are heated by incoloy-sheathed elements. The control system comprises of a direct reading thermostat and overheat thermostat both with calibrated scales and tamper proof locks. The controls also include a mains switch and indicator and heat and overheat indicators.

Temperature range 40°C to 250°C

Easy clean powder coated

Stainless steel interior

Fan fitted as standard

Specifications

Ref No. Capacity (Liters)

Internal Dimensions (H x W x D)

External Dimensions (H x W x D) with fan

No. of Shelves

No. of Shelf Positions

Net weight (Kg)

ICR400/30 30 24 x 36 x 35 cms 49 x 45 x 59 cms 2 2 20 ICR400/50 50 33 x 49 x 33 cms 58 x 61 x 57 cms 2 3 26 ICR400/75 75 33 x 49 x 46 cms 58 x 61 x 70 cms 2 3 34

ICA-150 Water Treatment

ICA-150 is ideally suited for all wastewater cleaning processes in modern PCB prototype laboratories. The units exist in four variants with different sump capacities and ion exchange capacities. A separate spray pump/reservoir module is included with the closed loop K systems, (not shown on dimensions opposite). This consists of a secondary reservoir and pump to enable the treated water to be introduced at pressure to the water inlet of the spray wash system being used.

Removal of solids and all heavy metals

Decrease of chemical oxygen demand

Easy handling and operation

Polyethylene filter candle, 10 µm

Lower and upper sump level control switch

Storage sump for 110 (ICA-150 A) or 220 litres (ICA-150 B) of waste water

ICA-150 A ICA-150 B

Size (H x D x L): 1400 x 425 x 600mm 1400 x 850 x 600mm Weight: 30 kg 60 kg Tank capacity: 110 l 220 l Cleaning capacity: 10 l/hour 20 l/hour Power supply: 230V~, 50Hz, 50W 230V~, 50Hz, 100W

12

PCB Equipments

ICM-500 Through-hole-planting line

Professsional equipment for laboratory prototyping of through-hole plated PCBs up to 210 x 300 mm size. Clean system including built-in rinsing compartment. Maintenance free and made for easy processing and handling. This particular machine type is optimized in terms of space requirements and costs. ICM-500 is suitable for most direct plating processes on the world market . Processing sequence for the ABC panel plating (tenting) technique:

Cleaner /Conditioner

Pre-dip

Catalyst

Intensifier

Copper plate Equipment:

5 treatment tanks, 2 of them with heaters

1 galvanic copper bath with air injection

1 triple-cascade rinse with cog valve flow control

1 spray rinse tank with solenoid valve, foot switch and flow control

1 free tank (i.e. for electroless tin) Rectifier:

1 Rectifier for copper plating 6 V / 40 A, separate current and voltage display and setting. Residual ripple < 0.1 % DC Bath control:

2 PTFE/PFA coated heaters, controlled by analogue instruments, full digital timers with countdown, auto-reset and beeper. Air injection into the copper plating bath. Board movement by DC gear motor, adjustable speed.

Tank dimensions Treatment tanks Galvanic copper tank

Length: 400 mm 400 mm Width: 100 mm 275 mm Depth: 300 mm 300 mm Capacity: 10 l 30 l Total size (W x D x H): 88 cm x 100 cm x 135 cm Working level: 95 cm Weight: approx. 80 kg Heaters: 2 x 400 W Rectifier: 1 x 6 V, 40 A Power supply: 230 V, 50 Hz, 6.3 A

13

PCB Equipments

34-01 Photo Etch PCB

Pre-sensitized copper clad board for PCB.

Description Code

Single faced, 1,5mm thick, 35mm Cu, 100 x 160mm 34-0105 Single faced, 1,5mm thick, 35mm Cu, 100 x 220mm 34-0110 Single faced, 1,5mm thick, 35mm Cu, 203 x 114mm 34-0115 Single faced, 1,5mm thick, 35mm Cu, 233.4 x 220mm 34-0120 Single faced, 1,5mm thick, 35mm Cu, 305 x 457mm 34-0145

34-02 Economy Photo Etch PCB

Pre-sensitized copper clad board for PCB.

Description Code

Double faced, 1,5mm thick, 35mm Cu, 100 x 160mm 34-0205 Double faced, 1,5mm thick, 35mm Cu, 100 x 220mm 34-0210 Double faced, 1,5mm thick, 35mm Cu, 203 x 114mm 34-0215 Double faced, 1,5mm thick, 35mm Cu, 233.4 x 220mm 34-0220 Double faced, 1,5mm thick, 35mm Cu, 305 x 457mm 34-0245

34-03 Plain Copper-Clad Fibreglass Circuit Board High quality 305g/m copper clad boards in epoxy glass material.

Thickness 1.6mm

Suitable etchant: ferric chloride solution

Description Dimension Code

Copper Clad Single Sided FR4 Fibre Glass Board 100 x 160mm 34-0300 Copper Clad Single Sided FR4 Fibre Glass Board 233.4 x 160mm 34-0305 Copper Clad Single Sided FR4 Fibre Glass Board 100 x 220mm 34-0310 Copper Clad Single Sided FR4 Fibre Glass Board 233.4 x 220mm 34-0315 Copper Clad Double Sided FR4 Fibre Glass Board 100 x 160mm 34-0320 Copper Clad Double Sided FR4 Fibre Glass Board 233.4 x 160mm 34-0325 Copper Clad Double Sided FR4 Fibre Glass Board 100 x 220mm 34-0330 Copper Clad Double Sided FR4 Fibre Glass Board 233.4 x 220mm 34-0335 Copper Clad Single Sided FR4 Fibre Glass Board 203 x 95mm 34-0360 Copper Clad Single Sided FR4 Fibre Glass Board 203 x 305mm 34-0365 Copper Clad Double Sided FR4 Fibre Glass Board 203 x 305mm 34-0345

14

PCB Equipments

34-04 Hard Paper Board Cu 35 µm Single Sided 1.5mm

The FR2 Hard Paper Boards Cu 35 µm Single Sided 1.5mm are copper-clad boards manufactured for low-cost printed circuit boards. Unlike the epoxy glass fibre version, the hard paper board is easier to drill, in the process contributing towards a longer life for drills and cutting tools.

Description Dimension Code

FR2 Hard Paper Board Cu 35 µm Single Sided 1.5 x 50 x 100mm 34-0520 FR2 Hard Paper Board Cu 35 µm Single Sided 1.5 x 60 x 100mm 34-0521 FR2 Hard Paper Board Cu 35 µm Single Sided 1.5 x 75 x 100mm 34-0522 FR2 Hard Paper Board Cu 35 µm Single Sided 1.5 x 100 x 100mm 34-0523 FR2 Hard Paper Board Cu 35 µm Single Sided 1.5 x 100 x 160mm 34-0524 FR2 Hard Paper Board Cu 35 µm Single Sided 1.5 x 150 x 200mm 34-0525 FR2 Hard Paper Board Cu 35 µm Single Sided 1.5 x 200 x 200mm 34-0526 FR2 Hard Paper Board Cu 35 µm Single Sided 1.5 x 200 x 300mm 34-0527

34-05 Epoxy PCB 1.6mm Grid Pitch 2.54mm

The Epoxy PCB 267 x 170 x 1.6mm Grid Pitch 2.54mm is a printed circuit board with a 1.6mm thickness - ideal for building electronic devices. Technical Specification

Dimensions Hole diameter PCB thickness Code

98 x 76.5mm (L x W) 1mm 1.6mm 34-0511 267 x 170mm (L x W) 1mm 1.6mm 34-0512

34-30002 Etch Resist Pen Etch Resist Pen, Artwork Preparation, Blue, On Plain Copper Boards Simply press the tip to promote ink flow Apply slow, even pressure in use

15

PCB Equipments

34-10 Electronics Solder Wire

The standard solder for hand soldering. Primarily for electronic and electrical applications

Diameter Weight Code

0.35mm 100g 34-10035 0.8mm 100g 34-10080 1.0mm 250g 34-10100

34-105 Solder Grease

Solder Grease is ideal for use with thick solder, where high heat is required. Ensures a good joint, e.g. when soldering metal sheets, copper pipes, brass, etc.

Description Code

Solder Grease 20g 34-1050 Solder Grease 50g 34-1051 Solder Grease 100g 34-1052

34-08 Etch-resist Transfers

High quality etch-resist transfers for preparing PCB layouts.

Circuits are prepared by rubbing down the transfers onto drafting film to produce artwork for UV exposure, etc.

May also be applied directly on to copper-clad board

Sheet size 255 x 90mm

Description Code

Assorted Pads 34-0870 Round Pads 1.9/0.45mm 2.1/0.45mm 34-0872 Round Pads 2.5/0.45mm 2.8/0.45mm 34-0874 DIL Pads 34-0876 Straight Tracks 0.5/1.0mm 34-0878 Straight Tracks 1.5/2.0mm 34-0880 0.5mm Tracks and Curves 34-0882 1.0mm Tracks and Curves 34-0884 1.5mm Tracks and Curves 34-0886 2.0mm Tracks and Curves 34-0888

16

PCB Equipments

34-0500 PCB Developer

PCB Developer is suitable for use with all alkaline developed, positive photo resists and fully aqueous dry film photo resists.

Safe to use: contains no sodium hydroxide

Suitable for use in our tanks

Developer gives a long tank life and fast developing time

Available either in dry crystalline form in packs of approx. 25g, sufficient to produce 500ml solution (1 litre when used with Fotoboard 2), or as 1 liter of concentrate, to make 10 liters of working solution (20 liters when used with Fotoboard 2)

The shelf life of the solution is considerably greater than that of the crystalline form and should be kept in undiluted form in an airtight container.

Description Code

Photoresist Universal Developer Crystals 34-05005 Liquid Developer Concentrate 1ltr for 10ltr - 20ltrs 34-05009

34-0501 Etch Resist Stripper

A stripper to remove the photoresist from an etched circuit board.

A 1 litre concentrate which makes 5 litres of working solution

Best used in a PCB processing tank at 45 to 50°C

Photoresist strips from the copper in approx. 2-3 minutes

Supplied in 1l bottles

34-0502 Ferric Chloride Etchant

A special formulation of ferric chloride for etching metals and all types of copper circuit boards.

Supplied as full strength, suitable for metals such as stainless steel, nickel, brass, etc.

Dilute by an additional 30% with water for use with copper

Supplied in 5 litre containers, weight 7.5kg

17

PCB Equipments

34-0748 Processing Tray

A high quality, rigid polystyrene processing tray for developing or tinning PCBs.

Spout facilitates emptying

All-round carrying lip

Size 254 x 203 x 55mm

Color may vary

34-071 Universal PCB Holder A board holder for up to 20 boards.

Manufactured from polypropylene

Impervious to almost all PCB manufacturing chemicals

Can be washed clean

Virtually indestructible

Excellent value for money

Greater rigidity over vacuum-formed alternatives

Size 400 x 77 x 25mm

34-072 Universal PCB Holder

Made from black conductive polypropylene, have multiple uses in the static free environment, as holding the PCBs during assembly, testing and rework.

Description Dimension Code

Conductive L-shaped, dimensions 208x272x93mm 34-07210 Conductive L-shaped, dimensions 355x268x128mm 34-07211 Conductive flat, 25 slots, 490x180x50mm 34-07212

18

PCB Equipments

34-073 PCB Holder

A professional line of assembly jigs for PCB's, designed to simplify placing and soldering of electronic components. Additional rails may be added to accomodate a large number of small boards. The frame and lid assembly may be detached from the mounting base. After mounting the components on the PCB's, the foam back lid is attached and closed, and the whole assembly is lifted and rotated for soldering. An ingenious design of the base permit an adjustable working angle on both side of the PCB's. The jig is varnished steel, and the component pressing foam is in conductive material.

Max working dimensions Code

270 x 220mm 34-07310 500 x 220mm 34-07311 500 x 350mm 34-07312

34-10002 Desoldering Suction Pump The Desoldering Suction Pump Aluminium ESD is an anti-static desoldering suction pump in metallic housing with self-cleaning tip and easy to use trigger head. Ideal for hobby and professional applications.

Anti-static

Robust aluminium housing

Easy to use release button

34-10003 Solder Iron Stand Heavy-duty soldering iron stands suitable for use with most soldering irons. Suitable for irons with a body diameter up to 12mm Heavy 700g die-cast base for stability A heavy chrome-plated steel spring encloses a shield for the iron which serves to maintain tip temperature and to protect users from accidental contact with the iron The stands are supplied with a sponge, which when kept moist, serves to keep soldering iron bits clean

19

PCB Equipments

34-10000 Solder dispenser A convenient method of dispensing solder.

Accepts most 500g reels of all gauges of solder

Installation of reel takes a matter of seconds

Spring guide holds end at convenient height and position

Heavy base maintains excellent stability

34-10001 Soldering stand with magnifier Ideal for awkward jobs where a third hand is needed Cast steel base for extra stability Fitted with two, fully articulated crocodile clamps and Ø50mm magnifying glass

34-0601 Rubber Gloves Green seamless rubber gauntlets. Natural rubber to provide maximum durability and give excellent protection against various chemicals. Medium weight. Various size.

34-0602 Laboratory Coat Protective coat made from durable material for use in laboratory, workshop, warehouse or factory. Very comfortable to wear and protects against dust, dirt and chemical splashes. Features include collar, stud-fastened front and straight-cut cuffs. Sizes small, medium and large.

• Elecricite et electronique• Controle des procedes • Pneumatique et electropenumatique• Technologie de l’automatisation• Installations electriques domotica• Electronique de puissance• Machines electriques• Moteurs et fluides pour machines• Systemes industriels d’entrainement• Maintenance et simulation des pannes sur ordinateur

• Communications analogiques• Realisation de circuits imprimes• Montage et reparation circuits imprimes• Soudage et equipement• Outils• Laboratoire de physique• Laboratoire de chimie• Laboratoire de biologie• Instrumentation electronique• Instruments electroniques analogiques• Instruments electroniques numeriques• Instrumentation electrique

• Electricity and electronics• Process control• Pneumatics and electropneumatics• Automation technology• Electrical installations domotic• Power electronics• Electrical machines• Motors and fluids for machines• Industrial training systems• Fault simulation and maintenance on personal computer

• Analog communications• Printed circuit realisation• Printed circuits assembly and repair• Soldering and equipment• Tools• Physics laboratory• Chemistry laboratory• Biology laboratory• Electronics instrumentations• Analog electronics instrumentation• Digital electronics instrumentation• Electrical instrumentation

Headquarter Via M. Idiomi 1/17 20090 Assago - Milan - ITALY Web: www.ofelitaly.com Mail: info@ofelitaly.com

Web: www.ofelengineering.it Mail: info@ofelengineering.it

Worldwide Branch Offices

• OFEL Sarl Algerie • OFEL Sarl Maroc• OFEL Spain• OFEL Mexico• OFEL Brazil• OFEL USA• OFEL Thailand• OFEL South Africa