· PDF fileWelding Protection Screen with curtain ... Strip light on ceiling with 2 lightening tubes. ... Excentric Orbital Sander

Art-No./ Description Qty.

Pos.No.: 02.1

64 072 003 SSpiral-air pressure hosepolyamide, with quick-action couplingand nozzle D770131Max. working pressure bar = 8Max. working length m = 4Length of hose m = 7.5Internal-/Extern.dia. mm = 6 x 8

2.00

Pos.No.: 02.2

63 226 001Air-cleaning gun D740015made of anodized aluminiumMax. air pressure bar = 4-6Nozzle diameter mm = 1,5_ of hose sleeve mm = 6,0Internal thread G = 3/8"

2.00

Pos.No.: 03.

28.WKS.508921Welding Protection Screen with curtainmobile on 4 castorsWeidth x height m = 1.45x2.00Height of protect. curtain m = 1.8red

2.00

Pos.No.: 04.1

32.TE.GL4000Suction board Model GL4000Country of Origin: Italyfor car body panels preparation andpainting works of small car body parts.Air suction and air cleaning unit withdouble layers high-efficiency filteringsytem with electric exhaust van.Board made of galvanized sheet metal.Control panel

Dimensions: approx.lxwxh mm = 4000x1200x700Max. airflow approx. cm/h = 16000Electric motor power hp = 7,5

Supply with exhaust duct 3 m, duct endpice with bird protection sreen

1.00

Pos.No.: 04.2

32.TE.GL4001Exhaust duct 4 m2 Duct angle 90°1 Duct wall fixation clamp1 Duct end funnel with bird protectionscreen

1.00

Pos.No.: 04.3

32.TE.GL4002Spare filter set

1.00

Pos.No.: 05.

32.CO.A00300LInfrared dryer Model A00300LCountry of Origin: Italyshort waves, 3 panelsWatt = 3000Voltage V = 230, 60 Hz

4.00

Pos.No.: 06.

75 345357GUtility Sink with cabinet, white, incl.1 sink1 drying area1 water tapDimension cm = 100x85x60

1.00

Pos.No.: 07.

32.MO.M-433-09Waterfall type painting and drying boothWith roof, extented lateral walls andopen front.Air suction systemBooth made of sheet metal.Strip light on ceiling with 2 lighteningtubes.Control panelDimensions lxwxh mm = 3000x1500x2400Max. airflow approx. cm/h = 11000Electric motor power hp = 3

Supply without exhaust duct system

1.00

Pos.No.: 08.

92 201 001 SHot air blower, steplessly electronicregulation of temperature via hand wheelBlower adjustable in 3 steps via oper-ating switch

Heating capacity Watt = 2000Hot air temperature °C = 50...600Air supply cap. l/min. = 150/300/500

1.00

Pos.No.: 09.

32.AN.AT/I1.5Spray gun for painting, Standard typeScrew action typeNozzle dia. mm = 1.5Suction cup ccm = 1000

4.00

Pos.No.: 10.

32.MO.1090401008Automatic spray gun cleaner, made ofstainless steel AISI 304 with automaticwashing and rinsing. For cleaning twospray guns in one cleaning process.Dimensions cm = 65x149x64Standard accessories:Double membrane pumpContainer with wide capacitywith own independent suction

2.00

Pos.No.: 11.01

32.AN.AT/LUX1.5Spray gun for painting, with lever locksuction feed cup, HVLP systemsuction cup clamp type, non drip systemNozzle dia. mm = 1.5Suction cup ccm = 1000Working pressure bar = 2.6

1.00

Pos.No.: 11.02

32.AN.AT/LUX1.8Spray gun for painting, with lever locksuction feed cup, HVLP systemsuction cup clamp type, non drip systemNozzle dia. mm = 1.8Suction cup ccm = 1000Working pressure bar = 2.6

1.00

Pos.No.: 11.03

32.AN.ATLUXS1.3Spray gun for painting, with gravityfeed cup, HVLP systemNozzle dia. mm = 1.2Gravity feed cup ccm = 600Working pressure bar = 2.6

1.00

Pos.No.: 11.04

32.AN.ATLUXS1.8Spray gun for painting, with gravityfeed cup, HVLP systemNozzle dia. mm = 1.8Gravity feed cup ccm = 600Working pressure bar = 2.6

1.00

Pos.No.: 11.05

32.AN.A/208 1.8Underbody coating gun with suction cupof aluminiumFixed nozzle dia. mm = 8Suction cup ccm = 1000Working pressure bar = 2.6Max.pressure bar = 8

1.00

Pos.No.: 11.06.1

45 202 001Flat brushpure black bristle, metal capWidth x bristle length mm = 25x40

2.00

Pos.No.: 11.06.2

45 202 035 SFlat brushpure black bristle, metal capWidth mm = 35

2.00

Pos.No.: 11.06.3


1.00

Pos.No.: 11.06.4


1.00

Pos.No.: 11.07

32.MO.10930010212 Dryers for water base paints complyingwith ROHS standard for new water basepaints. Air capacity adjustment.Work pressure bar = 2-4Air consumption ltr./min. = 350Sound level dB = 72With dryer holder with hoses.No. 32.MO.1093001022Made of aluminium.Swivelling by ° = 360Min. height cm = 20Max. height cm = 210Total weight kg= 10.5

1.00

Pos.No.: 11.08.1

48 231 001Sanding block made of soft-PVCLength x width mm = 130 x 70

2.00

Pos.No.: 11.08.2

48 223 003Corundum grinding paperfor applications in wood, metal andlacquering sectionsPaper size mm = 67x140Grain mm = 120

20.00

Pos.No.: 11.09.1

32.MAK.BO6040Excentric Orbital SanderPower input W = 750No-load speed rpm = 1600-5800Excentric speed rpm = 180.670Grinding stroke dia. mm = 5.5Grinding disc size _ mm = 150Suction stub int. _ mm = 15Weight kg = 2.7Switchable from excentric turnto rotationAccessories:

1.00

1 carrying case1 suction stub1 wrench

Pos.No.: 11.09.2

32.MAK.BO60401Set of grinding paper dia. 150 mm10 pcs. of grain K 8010 pcs. of grain K 15010 pcs. of grain K 320

1.00

Pos.No.: 11.09.3

32.MAK.BO60402Grinding disc dia. 150 mmSoft

1.00

Pos.No.: 11.09.4

32.MAK.BO60403Dust collection bag

1.00

Pos.No.: 11.10.1

32.MAK.9227CBAngular lapping/polishing machinePower input W = 1200No-load speed rpm = 0-3000Grinding disc size _ mm = 180Weight kg = 3Standard Accessories:Side handlePolishing hood dia. 180 mmfor woodGrinding disc dia. 165 mmCentering tube 18 mmWrench 6 mm

1.00

Pos.No.: 11.10.2

32.MAK.9227CB1Rubber disc M14, dia. 180 mm

1.00

Pos.No.: 11.10.3

32.MAK.9227CB2Polishing hood, dia. 180 mm

1.00

Pos.No.: 11.11.

32.MO.1093030008Paint thickness meter with serial outletRS 232 for metal and non metal surfacesMeasurement field µ = 0-1250Accuracy ± % = 1-3Weight gr = 812 calibration kits included

1.00

Pos.No.: 11.12

32.MO.1220901022Universal trolley for bumpers, carbonnets and doors, with 2 wheelsDimensions cm = 146x136x72

1.00

Pos.No.: 11.13

32.MO.1220901017Holder for car parts and mudgardsDimensions cm = 51x51x130

1.00

Pos.No.: 12.

13.IT.40085Air operated degreaser - cleaning tankin stainless steelThe basin (cap. 60 Ltrs.) is mounted ona 80 Ltr. reservoir.

1.00

Pos.No.: 13.

32.SI.220000Computerized paint mixing plantfor storing and mixing of any uni-colouror metallic paint colours plus water-based paints with a total of 95 painttins storage and mixing places.Comprising:2 Racks for 23 colour tins each 3,75 l4 Racks for 72 colour tins each 1 l1 Paint mixing system for total 95paint tins including electric driveand mechanical mixing gears

95 Tin lids/cover for paint tins1 PC computer with paint mixing software1 TFT monitor 19"1 High precision electronic balanceto be connected to the mixer foraccurate paint colour mixingcapacity 1-6 kgaccuracy 0,1 g

1 Label printer1 Set (500 pcs. of labels)1 Computer cabinet1 USB connecting cable

1.00

1 Set of -+paint colour sample cards1 Storage cabinet for paint colour sample cards

Supply without consumable paints

We have offered the more suitablecomputerized paint mixing system for total95 different mixing paints in order to beable to mix any uni-colour, metallic-colour orwater-based paint colour for automotiveapplication.

With only 16 different mixing paints you canonly realise a limited number of onlysingle-colours which does not fulfil therequirement of up to date large number ofcar body paints including metallic-paints.

Pos.No.: 14.

32.MA PA14Set of illustrative panelsshowing spray guns and painting uns technique

1.00

Pos.No.: 15.

74 549 001 SClip Shelf system, completel galvanizedFrame made of posts, steel feet platescover plates, Frame traverses andframe diagonalesShelves adjustable in height consistingof square tube side railsDimengsions HxLxD mm = 1972x2180x500consisting of:3 pcs.Frames height mm = 1972x5006 pcs.Shelves S1 mm = 900x5007 pcs.Shelves S1 mm = 1200x500

3 pcs.containers for shelf2 partitions mm = 900x500

3 pcs.containers for shelf2 partitions mm = 1200x500

4 pcs.wall hooks

1.00

12 pcs.plastic container boxesmm 500x180x95

Pos.No.: 16.

74 414 006Tool cupboard with 2 wing-doorsMade of sheet-steel, painted4 adjustable shelves with lateralledges as adjustable shelf supportsHeightxWidthxDepth mm = 1950x950x450Doors with safety bordering andreinforced at the rear-sidewit cylinder locking system on3 pointsColour: green RAL 6011

2.00

Pos.No.: 17.1

94 SC 215385Desk for teacherDimensions mm = 1600x800x720made of rectangular steel rube frame.Plate melamin coated. Quality E1Thickness mm = 28colour light grey RAL7035

1.00

Pos.No.: 17.2

94 SC 204020Container for deskmobile, with rollers 2 of it fixableDimensions mm = W420xD600xH537with two drawersone drawer with hanging file basket

1.00

Pos.No.: 18.

74 112 151 SOffice Chair with arm restHigh back type mm = 580

1.00

Seating depth mm = 410-460Seating width mm = 460Seating height mm = 420-550Hard weaering fabric cover made of100 % Polyester, black

Pos.No.: 19.1

73 344 039Worktable for assembly workFrame made of square tube mm = 30x30Adjustable in height mm = 800-850Plate dimensions mm = 1500x800with sheet steel top

2.00

Pos.No.: 19.2

73 345 003Drawer for work tableDimensions mm = 490x560x150RAL 5010

2.00

Pos.No.: 19.3

66 136 007Parallel-vicemilled clamping jaws, surface hardenedmade of steel, die forgedwith protected spindle and guide waysguide ways adjustableJaw width mm = 125Clamping width mm = 160For pipe-_ inch = 1/4 - 3Weight kg = 9,3

2.00

Pos.No.: 20.1

73 344 033Worktable for assembly workFrame made of square tube mm = 30x30Adjustable in height mm = 800-850Plate dimensions mm = 1500x800with beech wood top

1.00

Pos.No.: 20.2

73 345 003Drawer for work tableDimensions mm = 490x560x150

1.00

RAL 5010

Pos.No.: 21

74 154 003Swivel stoolCylindrique beech-wood seatBase of form pressed strip steelRAL 7021 anthracit paint finishAdjustable seat height

5.00

Pos.No.: 22.

98 108 003Protective gloves, made of NitrilApplication in automotive industry,petrochemical industry, print offices,paint spraying shopsProtection class = 3Length mm = 310Thickness mm = 0,4

24.00

Pos.No.: 23.

98 221 001 SSafety goggles, soft PVCadjustable elastic bandtransparent

24.00

Pos.No.: 24.1

98 407 001Double filter maskflexible double filter system withbayonet closingwithout filters

24.00

Pos.No.: 24.2

98 407 007Filter against gas and smoke, A2Packing unit = 2 pieces

12.00

Pos.No.: 24.3

98 407 015Filter against fine dust, P2

12.00

Packing unit = 2 pieces

Pos.No.: 25.

98 078 004Tyvek Pro-Tech OverallChemical protection overall with limitedwearing duration, protection class acc.PSA, cat. III type 5 and 6, antistaticSize XL

24.00

Pos.No.: 26.

78 500 025First Aid Box E for workshops up to25 persons with filling acc. toDIN 13 169 ESheet metal case, green36x26x10 cmfor Painting Section

1.00


Pos.No.: 08.0

13.RK.RV3000Valve Refacer Model RV3000Country of Origin: ItalyValve stem dia. mm = 4Grinding angle ° = 20-60Max. head dia. mm = 100Max. valve length mm = 400-450Valve length at 30°/45°mm min. = 75Head dia. 30° mm min. = 22Head dia. 45° mm min. = 18Grinding wheel size dia. mm = 175x30Grinding wheel speed rpm = 2800Electric power V = 230/400 3ph.

Hz = 50Valve dragg. wheel speed rpm = 14Dimension mm = 800x600x600Weight kg = 109

Standard Accessories:Allen wrench 2.5/3/4/5/6 mmOpen end wrench 8 mmValve dressing wheelValve stopDiamond support and valve end refacer

2.00

Pos.No.: 08.1

13.RK.RV30001Spare grinding wheel dia. 175x30corundum

2.00

Pos.No.: 29.

13.OKO.512Valve seat mill/reasmer setWorking range:Valve shaft-_ mm = 6-9Valve seat _ mm = 17-50

1.00

Pos.No.: 01.1

13.SP.02.004.05Electric equipment test bench Model 02.004.05Country of Origin: Italyfor cars/trucks up to 7.5 tonsfor alternators, stators, rotors, diodeplates, regulators and startersTests for alternators at 12/24 V up to2000 W with built-in or ext. regulator.Tests for electric users (windshieldwipers, intermittences, etc.).Test for plates with 6 and 9 diodes.Test for diodes (polarity, efficiency).Test for electronic regulators at 12/24 V.Test for starters (no load test and loadtest with brake max. 7 HP).Test condensers.Tes for insulations 220V (stators, engines,inductive fields)

Dimensions mm = 1030x480x1460Weight kg = 160

1.00

Pos.No.: 01.1.1

13.SP.6V140AHBattery 6V 140 Ah for test bench

2.00

Pos.No.: 01.1.2

13.SP.12V140AHBattery 12V 140 Ah for test bench

1.00

Pos.No.: 01.1.3

13.SP.04.035.00Tester for diode plates and electronicCountry of Origin: Italyregulators, 12-24 V,Power supply V = 220, 50 Hz. A.C.Output voltage 0.1-30V DCwith test cables and handbook

1.00

Pos.No.: 02.

43.HGL.P6060Regulated Dual Power SuppliesPeakTech 6060Output voltage 2x0-30V; 5V/3A fixedOutput current 2x0-10 AResidual ripple U 2mV<3A; 5 mV>3A;

10 mV fixed outputResidual ripple 3 mAAccuracy +/- 0.2 % rdg. + 2 dgt.

(Voltmeter)+/- 1.0 % rdg. + 2 dgt.(Amperemeter)

Operating voltage 100 ~ 127 V / 200 ~ 240 V AC50/60 Hz, switchable ext.

Dimensions 480x135x425 mmWeight 16 kg

2.00

Pos.No.: 03.1

13.MO.860Digital car multimeter/multitester 860for easy and fast basic diagnostic of

automotive electric/electronic systemsFunctions:Display: LCDMeasurements:-DCV, direct current voltsAC/DC: max. 10 ADiode check: 0,6 mA (VF=0,6V)Temperature: max. 750 °CDuty cycle: 1,0%-90%Voltage: max. 600 VContinuity buzzer: < 20 _

Sypply with:1 Guard case1 Battery2 Probes2 Prob extenions2 Grips1 Induction plier1 Instruction manual

Dimensions: 147x70x39 mmWeight: 350 g

4.00

Pos.No.: 03.2

01.LA.1085Compact pen-type digital multimeterSafety:IEC-1010; CAT II 600 V-LCD-display-Diode-, logic, continuity test-Auto-manual ranging-Auto power off-Data and maximum value holdDC voltage V = 600± 0,7 % + 2 dgt.

2.00

AC voltage V = 600± 0,8 % + 3 dgt.DC ampere mA = 0,01± 0,8 % + 3 dit.AC ampere mA = 0,01± 2,0 % + 3 dgt.Ohm _ = 20 m_± 1,0 % + 3 dgt.


Supply with:1 Carriying case1 Set of test leads1 Battery 2x1,5V AAA1 Operation manual

Pos.No.: 03.3

01.LA.1615Digital AC/DC Clamp Meter 1615Safety: EN 61010-1; CAT III 600 V-17 mm LCD-display, max.indication 3999-Disply: 3 3/4-digits-Data hold function-Blue backlight-Resistance-, frequency-, capacitance-,duty cycle-, temperature measurement

-Diode and continuity test-Auto/manual range selection-Auto power off

AC/DC current A = 1000AC/DC voltage V = 600Max contactor size mm = 31

Supply with:1 Type K-temperature probe1 Carriying case1 Set of test leads1 Battery

2.00

1 Operation manual

Pos.No.: 03.4

13.MO.1000Connection interfacesThey can be used with any type ofmultimeter, diagnostic instruments, oscilloscope.The allow a safe and fast connection tothe automobile systems to be checked(sensors, debimeter, injectors ect.AC/DC: max. 10 ADiode check: 0,6 mA (VF=0,6V)Temperature: max. 750 °CDuty cycle: 1,0%-90%Voltage: max. 600 VContinuity buzzer: < 20 _

Sypply with:1 Guard case1 Battery2 Probes2 Prob extenions2 Grips1 Induction plier1 Instruction manual


Digital engine tachometer is included in 03.1

2.00

Pos.No.: 03.5

13.CO.122624-62Digital laser contact less revolutioncounter-Min/max hold fuction-Backlight-Accuracy ± 0,005% + 1 Digit-Measurement distance 5-50 cm-Rpm range 2-99999Sypply with:1 9 v Battery1 Storage case1 Reflectorstrips 60 cm1 Operation manual

2 Spare reflectorstrips

1.00

Pos.No.: 04.0.1


2.00

Pos.No.: 04.0.2


2.00

Pos.No.: 04.0.3

66 136 007

2.00

Parallel-vicemilled clamping jaws, surface hardenedmade of steel, die forgedwith protected spindle and guide waysguide ways adjustableJaw width mm = 125Clamping width mm = 160For pipe-_ inch = 1/4 - 3Weight kg = 9,3

Pos.No.: 04.1.1

73 344 033Worktable for assembly workFrame made of square tube mm = 30x30Adjustable in height mm = 800-850Plate dimensions mm = 1500x800with beech wood top

4.00

Pos.No.: 04.1.2


4.00

Pos.No.: 05.

13.SP.04.033.00Timing light for petrol and diesel enginesCountry of Origin: Italy5 functions petrol and 2 for diesel:RPM 300 + 9990Dwell 20-99.9°Volt 0.1-60 VVolt peak 0.1-60 VAdvance 0.1-99.9°RPM dieselAdance diesel

3.00

Pos.No.: 06.1

73 241 09L100

6.00

Perforated Board for tools for wallmountingWithout mounting materialDimension mm = 1000 x 450Square holes mm = 10x10RAL 5010

Pos.No.: 06.2

73 261 09WBSET18Hook set 18-parts

3.00

Pos.No.: 10.1

73 225 05228B40Mobile workbenchWith 4 wheelsPlate beech wood mm = 401 drawer mm = 1801 cabinet door mm = 360Dimension mm = 1000 x 700 x 840RAL 5010

2.00

Pos.No.: 10.2

73 385 007Anti slip matmade of Nylon/PVCSize mm = 900x600x5

2.00

Pos.No.: 11.

13.IT.40085Air operated degreaser - cleaning tankin stainless steelThe basin (cap. 60 Ltrs.) is mounted ona 80 Ltr. reservoir.

1.00

Pos.No.: 12.

91 137 002 SHalogen flood light, portablewith halogen bulb 500 WattIP 44With cable length 1.8 m and plug 230 VWith steel pipe support, black

2.00

Pos.No.: 13.

30.T.BSTS2Automotive system and electronic trainerThe trainer consists of 4 main kits eachrepresenting automotive systems:-Automotive electric/electronic BSTS10training kit-Electronic ignition training kit BSTS20-ABS training kit BSTS30-LE fuel injection training kit BSTS40

The kits are used as a complete hands-onapproach to automotive systems, electric,electronic circuit for operation, dianostic,trouble shooting and testing techniques.Trainees learn industry related skillsin a step by step learning program thatdoes not require prior electrical training.The courses use automotive circuit schemes,moulded components with sectioned diagrams,being connected as integrated automotiveelectric, electronic circuit.

An additional kit of used real componentsenhances the hands-on experimental anddiagnostic work of the trainees as reallife conditions are recreated.

Supply with four training manuals in englishlanguage.

4.00

Pos.No.: 14.1

68 T 829034Battery charger and starter, 1-phase,Country of Origin: Italymicro processor controlledMains voltage V = 230Absorbed power charge kW = 1.5Absorbed power start kW = 9.5Charge/starting voltage V = 6/12/24Charge voltage V = 12/24Effective charge current A = 75Rated charge current A = 40Start current 1V/C A = 300Max. starting current A = 400Charge current regulation A = 1-40Min. rated ref. capacity Ah = 10Max. rated ref. capacity Ah = 600Dimension mm = 390x260x230Weight kg = 19.5

1.00

Pos.No.: 14.2

68 T 803002Trolley for car spotter 5500 PlusDimensions cm = 51x48x84Weight kg = 13.5

1.00

Pos.No.: 15.

68 T 829321Battery charger with starter, 1-phase,Country of Origin: Italymobile, for lead-acid batteries.Mains voltage V = 230Absorbed power charge/start. kW = 1.6/10Charge/starting voltage V = 12/24Charge current A = 75Conventional current A = 50Absorbed power charge/start. kW =Starting current max. A cc = 400Conventional current A = 300Rated reference cap. Ah 15h min.= 20

max.= 1000Charge current regulation = 4Dimension mm = 330x360x650Weight kg = 16.3

-Protection against overloads and

1.00

polarity reversal-Choice of normal charge-Quick charge (BOOST)-Qucik start-Display of charging and starting current

Pos.No.: 16.

13.G 605Battery acid tester

5.00

Pos.No.: 18.

13.G 610Battery service kit, 13-piecesin sheet steel carrying case withacid proof plastic insertComprising:1 Double open ended spanner mm = 10x131 Water pump plier DIN 5231/B mm = 2401 Screwdriver mm = 6,51 Steel wire cleaning brush1 Bulb filler1 Acid tester1 Terminal puller 2 arms 60x60 mm1 pole clamp reamer1 cable knife1 isolating tape1 Battery carriying strap L mm = 4701 Plastic bottle l = 2

1.00

Pos.No.: 18.1.1

13.G 1.12/02Battery terminal puller, 2-legsOpening mm = 60Travel mm = 40

1.00

Pos.No.: 18.1.2

13.G 609Battery carrying strapwith two clamping eylets

1.00

Pos.No.: 18.1.3

13.BE 01757 006Battery fillerplasticContents cc = 1000

1.00

Pos.No.: 18.2.1

13.BE 01757 004Battery fillerplastic

1.00

Contents cc = 500

Pos.No.: 18.2.2

65 422 012Measuring canmade of plastic, oil, acid proofwith pouring spout and volume scaleCapacity ltr. = 1,0

1.00

Pos.No.: 18.2.3

13.BE 01757 006Battery fillerplasticContents cc = 1000

1.00

Pos.No.: 18.2.4

13.BE 017570020Battery fillerplasticContents cc = 1000

1.00

Pos.No.: 18.2.5

13.BE 1758Plastic funnelLength mm = 410Dia. mm = 95

1.00

Pos.No.: 20.1

13.VB.10090Dynamo for cars on baseSectioned training modelDimensions cm = 25x20x20Net weight kg = 6

1.00

Pos.No.: 20.2

13.VB.10080Alternator for cars on baseSectioned training modelDimensions cm = 25x20x20Net weight kg = 4

1.00

Pos.No.: 20.3

13.VB.10070Starting motors for cars on baseSectioned training modelDimensions cm = 25x20x20Net weight kg = 6

1.00

Pos.No.: 20.4

13.VB.10060Distributor on baseSectioned training model

1.00

Pos.No.: 20.5

13.VB.10050Coil on baseSectioned training model

1.00

Pos.No.: 20.6

13.VB.10040Car batterySectioned training model

1.00

Pos.No.: 20.7

13.VB.10020Preheating plug circuit operating systemon baseSectioned training modelThe glow plug preheating circuit of anindirect inject. diesel engine is shownDimensions cm = 70x25x55Net weight kg = 10

1.00

Pos.No.: 20.8

13.VB.10000Coil ignition unit on baseSectioned training modelA plastic-plated wooden base is the sup-port of the main components of the coilignition of a 4-stroke engine:battery, spark coil, coil, spark plugs.Rotating flywheel shows the peration ofthe whole unit (the action of theplatinum points and of teh distri-

1.00

butor can be obsered through thesection) and the spark flashingin the respective spark plugs isshow as well.Dimensions cm = 70x25x55Weight kg = 10

Pos.No.: 21.

74 549 001 SClip Shelf system, completel galvanizedFrame made of posts, steel feet platescover plates, Frame traverses andframe diagonalesShelves adjustable in height consistingof square tube side railsDimengsions HxLxD mm = 1972x2180x500consisting of:3 pcs.Frames height mm = 1972x5006 pcs.Shelves S1 mm = 900x5007 pcs.Shelves S1 mm = 1200x5003 pcs.containers for shelf

2 partitions mm = 900x5003 pcs.containers for shelf

2 partitions mm = 1200x5004 pcs.wall hooks


1.00

Pos.No.: 22.


3.00

Pos.No.: 23.


12.00

Pos.No.: 24.1


1.00

Pos.No.: 24.2

94 SC 204020

1.00

Container for deskmobile, with rollers 2 of it fixableDimensions mm = W420xD600xH537with two drawersone drawer with hanging file basket

Pos.No.: 25.

74 112 151 SOffice Chair with arm restHigh back type mm = 580Seating depth mm = 410-460Seating width mm = 460Seating height mm = 420-550Hard weaering fabric cover made of100 % Polyester, black

1.00

Pos.No.: 26.

78 500 025First Aid Box E for workshops up to25 persons with filling acc. toDIN 13 169 ESheet metal case, green36x26x10 cm

1.00

Pos.No.: 27.


1.00


Pos.No.: 1.

13.ABA.B70500Silent air compressor Model B70500country of origin: Italyfor use in industry and handicraftPower connection V = 400/50/3Motor power kW = 7.5Tank capacity ltr. = 500Max. pressure bar = 10Intaken air ltr./min. = 1210Air supply Ltr./min. = 920Slow speed rpm = 1300Noise level dB(A) = 85Dimensions LxWxH mm = 2025x1000x1680Weight kg = 370

incl. star delta switchoil lubricated 2 cylinder aggregate2 stage

1.00

Pos.No.: 02.1

13.CE.SM916Semi-automatic tyre changer Model SM916Country of Origin: Italyfor car wheelsSwing arm typeMax. Wheel dia. mm = 1000Max. rim width mm = 340Rim dia. ext. clamp." = 10-24Power supply V = 230/400, 3-ph.Motor Power kW = 0.55Rotation speedWorking pressure bar = 10Inflat. pressure bar = 3.5Torque Nm = 1150Max. Bead loosenercylinder force N = 30800Net weight kg = 200

Standard Accessories:Pressure gaugeTyre leverLubricatorFat tin holder

1.00

Pos.No.: 02.2

13.CE.937098185Asturo inflating gun

1.00

Pos.No.: 03.

13.CE.CM260TSemi-automatic tyre changer Model CM260TCountry of Origin : Italyfor heavy vehicle-truck wheelsfor wheels from " = 14-26Max. wheel weight kg = 1500Max. wheel width mm = 780Max. wheel dia. mm = 1200Hydr. pump motor cap. kW = 0.75Voltage V = 3-ph. 230/400Operat. pressure forhydr. circuit bar = 0-130Gearbox motor cap. kW = 1.5Voltage V = 3-ph. 230/400Bead breaker forceinside-outside kg = 1500Noise level in workingcondition db = <70Net weight kg = 400

Standard equipment:double function tool and bead-liftinglever for tyres with tube and 1-piecerim or tubeless tyres. Wheel lockingthrough adaptor and cones for wheelswith central hole from 105 to 300 mm

1.00

Pos.No.: 04.1

86 417 003Workshop grinding machine model SM 200Grinding wheel dimens. mm = 200x30x32Grain 36K/K80Voltage V = 230

W = 600Speed rpm = 2850Standard Accessories:Sturdy, longlife industrial-executionAdjustable work piece support1 grinding wheel normal corundumcoarse

1 grinding wheel normal corundum

1.00

fineSpark protectionUnder voltage releaseEmergency off

Pos.No.: 04.2

87 417 9031SPedestal for workshop grinderwith cabinet and internal shelfContainer for waterDimensions LxWxH mm = 345x300x785

1.00

Pos.No.: 04.3

98 211 050 SUniversal safety goggelsnylon frame,with colourless plastic lenseswith foldable side protectionlense size mm = 62x52

1.00

Pos.No.: 05.1


2.00

Pos.No.: 05.2


2.00

Pos.No.: 05.3

66 136 007Parallel-vicemilled clamping jaws, surface hardenedmade of steel, die forged

2.00

with protected spindle and guide waysguide ways adjustableJaw width mm = 125Clamping width mm = 160For pipe-_ inch = 1/4 - 3Weight kg = 9,3

Pos.No.: 07.

13.LA.P40Pneumatic Vulcanizer Model P40country of Origin: Italyfor cars and light trucksHeating unit size cm = 19x10Cap. Watt = 1200Power supply V = 230Pressure bar = 10Net weight kg = 29.4Pneumatic clamping deviceTimerPressure adjustmentTwo heating unitsFor repairing any type ofstandard, radial and tubeless tyrein any position.

1.00

Pos.No.: 07.1.1

13.PR.PBV-32Black Vulc Cement(cement for hot vulcanisation)Container ml = 946

1.00

Pos.No.: 07.1.2

13.PR.PURF-2Universal round patch no. 2Dia. mm = 50 (52)Packing Unit = 50 piecesPrice for packing unit

3.00

Pos.No.: 07.1.3

13.PR.PURF-3Universal round patch no. 3

3.00

Dia. mm = 70 (75)Packing Unit = 50 piecesPrice for packing unit

Pos.No.: 07.1.4

13.PR.PR-109Patch no. 109 for radial repairDim. approx. mm = 77x50Packing Unit = 20 piecesPrice for packing unit

5.00

Pos.No.: 07.2.1

13.PR.PURF-1TUniversal round patch no. 1Dia. mm = 30 (32)Packing Unit = 500 piecesPrice for packing unit

1.00

Pos.No.: 07.2.2

13.PR.PB-1Patch no. PB-1 for diagonal repairDia. mm = 62Packing Unit = 25 piecesPrice for packing unit

8.00

Pos.No.: 08.1

13.O 116Hydraulic trolley jackstandard lifting heigthwith:- Fixing of handle- Overload valve- Sturdy, approved construction- Good stability- Convex cast iron wheels and castors- Lifting and lowering withmanoeuvering handle

- with foot-lever quick actionlifting device

Technical data:

1.00

Capacity kg = 3000Max. height mm = 520Min. height mm = 140Stroke mm = 380Frame length approx. mm = 2100Weight kg = 56

Pos.No.: 08.2

13.O 118Hydraulic trolley jackstandard lifting heigthwith:- Fixing of handle- Overload valve- Sturdy, approved construction- Good stability- Convex cast iron wheels and castors- Lifting and lowering withmanoeuvering handle

- with foot-lever quick actionlifting device

Technical data:Capacity kg = 5000Max. height mm = 550Min. height mm = 155Stroke mm = 395Frame length approx. mm = 1530Weight kg = 80

1.00

Pos.No.: 09.

13.US.496Tool assortment for car repaircomprising 135 pieces toolsNet weight kg = 27

1.00

Pos.No.: 10.

13.STG TYRLEVSet of levers and tyre pullersconsisting of:1 tyre lever 8482826 mm = 3031 tyre lever 8482857 mm = 6001 tyre lever 8400499 mm = 4551 shaped tyre lever 51968921 lever for tubeless 5196957

1.00

Pos.No.: 11.1

62 002 011 SEngineer’s hammer acc. DIN 1041die forged and hardenedGerman pattern, black paintedwith ash-wood handleWeight without handle kg = 1.0Length mm = 360

1.00

Pos.No.: 11.2

62 002 013 SEngineer’s hammer DIN 1041die forged and hardenedGerman pattern, black paintedworking faces groundwith ash-wood handleWeight without handle kg = 1,5Length of handle mm = 380

1.00

Pos.No.: 11.3

62 013 003 SMallet acc. DIN 6475 (Sledge hammer)

1.00

German pattern, black paintedhardened, with ash-wood handleWeight without handle Kg = 1.5Length mm = 280

Pos.No.: 11.4

62 009 001 SSledge hammer DIN 1042German pattern, die forgedtotally ground, black paintedwith ash-wood handleWeight without handle Kg = 3.0Length of handle mm = 600

1.00

Pos.No.: 11.5

62 009 003 SSledge hammer DIN 1042German pattern, die forgedtotally ground, black paintedwith ash-wood handleWeight without handle Kg = 5,0Length of handle mm = 800

1.00

Pos.No.: 12.1

13.E 195WS-1/2Four way wheel nut wrenches for carshigh grade tool steel17, 19, 1/2", square pattern, 22Length mm = 400

3.00

Pos.No.: 12.2

13.E 195CV-3/4Four way wheel nut wrenchChrome Vanadium 31 CrV324, 27, 32, 3/4", square patternLength mm = 750

3.00

Pos.No.: 13.


1.00

Pos.No.: 14.1

64 072 003 SSpiral-air pressure hosepolyamide, with quick-action couplingand nozzle D770131Max. working pressure bar = 8Max. working length m = 4Length of hose m = 7.5Internal-/Extern.dia. mm = 6 x 8

2.00

Pos.No.: 14.2

63 226 001Air-cleaning gun D740015made of anodized aluminiumMax. air pressure bar = 4-6Nozzle diameter mm = 1,5_ of hose sleeve mm = 6,0Internal thread G = 3/8"

2.00

Pos.No.: 14.3

63 235 001 STyre pressure gauge D040011Work pressure bar = 7Length of hose cm = 41Gauge-_ mm = 63Weight kg = 0.4

2.00

Pos.No.: 15.

13.MA TY015Illustrative panels showing tyres

1.00

Pos.No.: 16.

13.FA.V555Wheel balancer Model V555Country of Origin: Italyhigh tech 16bit PC-basedVideo LCD SVGA 17"Power source V = 220, 50-60 Hz. 1PhMotor power W = 50Power required W = 400Rotation speed rpm = 98Rim dia. mm = 200-650Rim dia. (alu-s) " = 8-23Wheel dia. max. mm = 850with wheelguardRim width max. mm = 415with wheelguardWheel weight kg = 90Measur. time s = 4-15Accuracy g = 1Monitor SVGA = 17"Standard Equipment:easy-alu basementcones 38-98 mmPlierDistance and diameter automaticinputIFS-HD shaftOptimizationAFC Automatic Flange CalibrationUser set-upStatisticsDynamicStaticAlu programsMoto mode

1.00

Pos.No.: 17.01

13.PR.PW-ZNSC10Wheel weight, zinc, clip-on typefor universal steel rimsWeight g = 10Packing unit = 100 pcs.Price for packing unit

1.00

Pos.No.: 17.02


1.00

Pos.No.: 17.03


1.00

Pos.No.: 17.04


1.00

Pos.No.: 17.05


1.00

Pos.No.: 17.06

13.STG 518 7801Plier for wheel weights

1.00

Pos.No.: 17.1.1

13.PR.PW-ZNAC5

1.00

Wheel weight, zinc, clip-on typefor alloy rimsWeight g = 5Packing unit = 100 pcs.Price for packing unit

Pos.No.: 17.1.2

13.PR.PW-ZNAC15Wheel weight, zinc, clip-on typefor alloy rimsWeight g = 15Packing unit = 100 pcs.Price for packing unit

1.00

Pos.No.: 17.1.3


1.00

Pos.No.: 17.1.4


1.00

Pos.No.: 17.1.5


1.00

Pos.No.: 17.1.6

13.PR.PW-ZNAC40

1.00

Wheel weight, zinc, clip-on typefor alloy rimsWeight g = 40Packing unit = 50 pcs.Price for packing unit

Pos.No.: 18.

13.FA.VDPCLAWheel Aligner Model VDPCLACountry of Origin: ItalyPentium-class CPU, 17"SVGA monitorPower source V = 200-240/50-60 HzPower required W = 500Wheel dia.- cars " = 10-21- trucks " = 17-26Power required W =Measuring acc. = 0.01°/0.1 mmMeasuring ranges:Total toe = ±40°Single toe = ±20°Camber = ±10°Caster = ±28°Lock angle = ±40°

Standard Equipment:Classic 1 sensorsRemote controlContact clampers,Standard turntablesSteering lockBrake lockCablesElectronic track gauge

1.00

Pos.No.: 19.

13.STG TYRTOOLTool set for tyre repair

1.00

consisting of:3 stitchers stand. corrugated 59610271 rubber knife, 250 mm 59521842 skiving knife 59520741 offset flexible knife 59521391 rasp 6.5 mm 59589441 patch marking pen 59589441 pneumatic tyre spreader 51769841 brass bristle brush 59545531 steel bristled brush adjust.59500691 pincer with lever nose 8426985

Pos.No.: 20.

13.LA.VL16Country of Origin: ItalyInner tube and tubless tyre test tankTank dimensions LxWxH mm = 920x920x1800Max. wheel dia. mm = 680Max. wheel width mm = 260Operating pressure bar = 6-8Weight net kg = 68

1.00

Pos.No.: 21.

13.O 110 BStand for cars and trucksMin./max. heigth mm = 440/760Max. load kg = 3500

8.00

Pos.No.: 22.

13.US.928 C1/S11Impact wrench kit, 11 pcs., 1/2"Comprising:8 pcs. Hexagonal sockets 1/2" 10-271 pcs. Extension 236 mm1 pcs. Oiler1 Impact wrench 928 C1:

Mac. capacity M16Torque range 30-500 NmMax. torque 610 NmAir inlet thread 1/4"Air pressure 6,2 bar

Net weight kg = 6,9

1.00

Pos.No.: 23.

76 180 002 SPlatform truck with grid at front sidesteel pipe constructionwith 2 swivel castors and 2 castors,roller bearing, solid rubber tyres 200 _wooden platformCapacity kg = 500Platform mm = 1200x800Grid mm = 50x50x4Grid height mm = 500Outer dim. mm = 1320x800x990

1.00

Pos.No.: 24.


1.00

Pos.No.: 24.

94 SC 204020Container for deskmobile, with rollers 2 of it fixable

1.00

Dimensions mm = W420xD600xH537with two drawersone drawer with hanging file basket

Pos.No.: 25.


1.00

Pos.No.: 26.


2.00

Pos.No.: 27.


1.00

Pos.No.: 28.


1.00


Pos.No.: 02.2

28.BE.TI100 AS1Workbench for brazing, gas, arc welding and cuttingcountry of Origin: Germanymade of rigid profiled sheet steelconstructionBenchtop made of firebrick and steelgradeThe steel grade is fitted with a seriesof cutting 24 pcs. cutting supports madeof cast iron which can be clamped on thethe steel grade for both gas and arccutting, keeping distance from the workpiece to be cut and the grade itself

The undertop of the bench is equipped withone large slag tray/drawer easy to be cleanedUnderneath the slag tray/drawer a drawer isfitted to store toolsA stainless detachable steel bin for quenchingwork pieces is fitted to the right of the benchA U-channel is fitted to the right of the benchto store welding rodsA gas burner support is fitted to the right frontcorner of the bench top.A work positioner, holder upright with horizontal

arm is fitted to the left rear corner of the benchtopThe horizontal arm is fitted with an workpiececlamp which allows to place workpieces in anydesired angle/position to facilitate the jobof the welder

The upright is fitted with an additional fixtureto hold a possible optional welding fume hood

Dimensions:Workbench wxdxh mm = 1010x800x8502 Steel grade wxdxh mm = 750x245x35

2.00

1 Fire bricks wxdxh mm = 750x250x301 Slag tray wxdxh mm = 800x800x401 Tool drawer mm = 600x600x1001 Storage try mm = 800x800x20

Supplied dismantled

Pos.No.: 03.1

68 T 817006Single-phase Alternating Current Welderon wheels, Model EURARC320country of Origin: ItalyMains voltage V = 230/400Absorbed Power 60 % kW = 3.5/9No-load voltage V = 52/76Current Range A = 45-250Welding current 60 % ED A = 125Usable Electrodes _ mm = 1.6-5Insulation class = H / IP 22Dimensions mm = 690x390x480Weight kg = 37

4.00

Pos.No.: 03.2

68 T 801102MMA welding Kit 250 A consisting of:2 Dinse plugs DX 251 electrode holder 300A1 Filter 51X1081 cable 25 mm2 2 m1 cable 25 mm2 3 m1 hand shield1 earth clamp 300 A1 slag hammer with brush

4.00

Pos.No.: 04.1

68 T 817008Single-phase Alternating Current Welderon wheels, Model EURARC420Country of Origin: ItalyMains voltage V = 230/400Absorbed Power 60 % kW = 4.5/13No-load voltage V = 52/73Current Range A = 70-350Welding current 60 % ED A = 170

15 % ED A = 320Usable Electrodes _ mm = 2-6Insulation classe = H / IP 22Dimensions mm = 890x460x590Weight kg = 63

1.00

Pos.No.: 04.2

68 T 801095MMA Welding Kit for EURAC4201 welding cable 35 mm2, 4 m, DX 50

with electrode holder 400 A1 earth cable 35 mm2, 3 m, DX 50

with earth clamp 400 A1 welding shield1 slag hammer

1.00

Pos.No.: 05.1

68 T 8150493-Phase Inverter Welding Machine, port-able, fan-cooled, Model Superior TIG301Country of Origin: ItalyMains voltage 1-phase V = 400Absorbed current A = 16Absorbed power kW = 7.5Mains Fuse A = 10No-load voltage V = 100Power factor cos = 0.7Current range in DC A = 7-280Max. current 35% in DC A = 280Current 60% in DC A = 180Usable electrodes in DC mm = 1.6-5

1.00

Insulation classe = F / IP 23Dimensions mm = 475x170x340Weight kg = 15.2acc. to CE Norm

Microprocessor controlled

Pos.No.: 05.2

68 T 801081MMA Welding Kit for Superior TIG1 welding cable 25 mm2, 4 m, DX 50

with electrode holder 400 A1 earth cable 25 mm2, 3 m, DX 50

with earth clamp 400 A1 welding shield1 slag remover1 connector

1.00

Pos.No.: 05.3

68 T 802607TIG Welding Kit comprising:Argon gas bottle IT adaptorWork clamp 300 ACableGas regulator 2 manometersTig torch 4 mKit of 10 pure tungsten electrodes 1.6mm

1.00

Pos.No.: 05.4

68 T 803051TrolleyDimensions cm = 77x56.5x89.5Weight kg = 30

1.00

Pos.No.: 05.5

28.LUE.AR50Argon cylinder, 50 Literempty

1.00

Pos.No.: 05.6

68 T 802222TIG Tungsten electrode Ceriato Grigio/DCgrey, WC 20 (for carbon, alloyed steel)_ 1,6 mm, length 175 mmPrice per 10 pieces

5.00

Pos.No.: 05.7

68 T 802232TIG Tungsten electrode Ceriato Grigio/DCgrey, WC 20 (for carbon, alloyed steel)_ 2,4 mm, length 175 mmPrice per 10 pieces

2.00

Pos.No.: 05.8

68 T 802240Electrode collet_1,6 mmPrice per 3 pieces

2.00

Pos.No.: 05.9

68 T 802241Electrode collet_2.4 mmPrice per 3 pieces

1.00

Pos.No.: 05.10

68 T 802250Electrode diffuser_1,6 mmPrice per 3 pieces

2.00

Pos.No.: 05.11

68 T 802251Electrode diffuser_2.4 mmPrice per 3 pieces

1.00

Pos.No.: 05.12

68 T 802231Kit 0f 10 Ceramic nozzlessize 6Price for 10 pieces

2.00

Pos.No.: 05.14

68 15125 1.6WIG Welding rodsMaterial = 1.5125Diameter mm = 1.6Length mm = 1000Cardboard box kg = 25(Packing unit 25 kg)

05.15 Aluminium rod dia. 1.6 mm cannot be usedwith Superior TIG 301 DC HF/LIFT, thus weoffer optional welding unit for aluminiumwelding separately for your kind reference.

1.00

Pos.No.: 06.

68 T HIL19113Rutile electrode, VelvetaDia. mm = 2.0Length mm = 300Packing unit kg = 4.0Price per packing unit

37.00

Pos.No.: 07.1

68 T 821010Single-phase wire welding machineModel Bimax 132, fan-cooledCountry of Origin: ItalyMains Voltage V = 230Absorbed Power kW = 1.3/3.6

Mains Fuse A = 10Power Factor 60 % cos = 0.9Max. no load voltage V = 30Current range A = 50-120

2.00

Current 60 % A = 50Adjustment positions = 4Steel welding wire dia. mm = 0.6 and 0.8Aluminium welding wire dia. mm = 0.8Insulation class = Hprotection degree = IP 21Dimensions mm = 480x275x380Weight kg = 21with thermostatic protection1.8 m cable 10 qmm1 Filter 51x1081 flux core wire coil 0.9 mm, 0.2 kg1 hand shield1 MIG torch 2 m 160 A1 slag remover1 work clamp 150 A

Pos.No.: 07.2

68 T 802036Aluminium welding kitcomprising:Aluminium wire coil dia.0.8 mm, 0.45 kgAL/Flux contact tip dia. 0.8 mmConical nozzleFeed roll dia. 0.6-0.8 mmSpindle

1.00

Pos.No.: 07.3

68 T 802037Stainless steel welding kitcomprising:Stainl.steel wire coil dia.0.8 mm, 0.5kgConical nozzleContact tipFeed roll dia. 0.6-0.8 mm

1.00

Pos.No.: 07.4

68 T 802051Stainless steel wire coilWire dia. mm = 0.8Weight kg = 0.5

2.00

Pos.No.: 07.5

68 T 802062Aluminium wire coilWire dia. mm = 0.8Weight kg = 0.45

4.00

Pos.No.: 07.6

68 T 802133Steel wire coilWire dia. mm = 0.8Weight kg = 0.8

4.00

Pos.No.: 07.11

28.KF.AR05Steel cylinder, EMPTY, with cylinder capand valve acc. DIN 477for Argon 4.6Charg. pressure bar = 200Testing pressure bar = 300For approx. Liter = 5For contents cbm = 1.0

1.00

Pos.No.: 08.

28.BE.TI100 AS1Workbench for brazing, gas, arc welding and cuttingCountry of Origin: Italymade of rigid profiled sheet steelconstructionBenchtop made of firebrick and steelgradeThe steel grade is fitted with a series

of cutting 24 pcs. cutting supports madeof cast iron which can be clamped on thethe steel grade for both gas and arccutting, keeping distance from the workpiece to be cut and the grade itself

The undertop of the bench is equipped withone large slag tray/drawer easy to be cleaned

1.00

Underneath the slag tray/drawer a drawer isfitted to store toolsA stainless detachable steel bin for quenchingwork pieces is fitted to the right of the benchA U-channel is fitted to the right of the benchto store welding rodsA gas burner support is fitted to the right frontcorner of the bench top.A work positioner, holder upright with horizontalarm is fitted to the left rear corner of the benchtopThe horizontal arm is fitted with an workpiececlamp which allows to place workpieces in anydesired angle/position to facilitate the jobof the welder

The upright is fitted with an additional fixtureto hold a possible optional welding fume hood

Dimensions:Workbench wxdxh mm = 1010x800x8502 Steel grade wxdxh mm = 750x245x351 Fire bricks wxdxh mm = 750x250x301 Slag tray wxdxh mm = 800x800x401 Tool drawer mm = 600x600x1001 Storage try mm = 800x800x20Supplied dismanteled

Pos.No.: 09.

28.WKS.508921Welding Protection Screen with curtainmobile on 4 castorsWeidth x height m = 1.45x2.00Height of protect. curtain m = 1.8red

2.00

Pos.No.: 11.1

68 452 011Gas cylinder trolleytubular steel construction with tool box2 cylinder fixtures side by sidewith safety chainwith hand protectionwith hose carrier on the handleswith base platewith air tyrefor cylinder diameter mm = 210/229For cylinder capacity l = 40/50Wheel diameter mm = 400Dimensions HxW mm = 1500x650Colour:blueWeight kg = 26(without cylinders)

1.00

Pos.No.: 11.2

28.KF.SA50Steel cylinder, EMPTY, with cylinder capand valve acc. DIN 477for oxygenCharging pressure bar = 200Testing pressure bar = 300nominal contents cbm = 10.0

1.00

Pos.No.: 11.3

28.KF.AZ40Steel cylinder, EMPTY, with cylinder capand valve acc. DIN 477for acetylenefor Liter = 40nominal contents kg = 6.3

1.00

Pos.No.: 12.1

68 215 002 SOxy-acetylene Welding and Cutting Setfor 17 mm shaftWelding range mm = 0.5-30Cutting range mm = 3 -100Comprising:1 Pcs. Torch-handle w.cup-nut/tail end8 pcs. welding inserts 0.5-301 pc. circle guideCutting nozzles 3-100 mm1 pc. cutting attachment withspring type lever

1 pc. pistol shaped lighter1 pc. universal spanner1 pc. pressure regulator oxygen1 St. pressure regulator acetyleneSupplied in metal case

1.00

Pos.No.: 12.2

68 269 006Flashback arrester for oxygenacc. to DIN 85 21for mounting to the pressure reducerConnecting thread 2 x G 1/4" right

1.00

Pos.No.: 12.3

68 269 009Flashback arrester for acetyleneacc. to DIN 85 21for mounting to the pressure reducerConnecting thread 2 x G 3/8" left

1.00

Pos.No.: 12.4

68 616 006 SUniversal welding gogglesnylon frame, mount to EN 166/169with coloured oval lenses DIN 6Flap ear pieces. The lenses are fixedwith a screw in the middleWeight kg = 0.044

1.00

Pos.No.: 12.5

93 410 005Twin hose acetylene, oxygene EN 559Innen-_ x Wandstärke mm = 6 x 5/9 x 3,5Price per m

5.00

Pos.No.: 12.6

68 237 005 SNozzle cleanersfor welding torchesset of 9 needles in holder

1.00

Pos.No.: 12.7

68 268 001Ass hose couplerfor acetylene and oxygen hosesmade of aluminiumFor hose diameter mm = 16

4.00

Pos.No.: 13.1


1.00

Pos.No.: 13.2


1.00

Pos.No.: 13.3

66 136 007Parallel-vice

1.00

milled clamping jaws, surface hardenedmade of steel, die forgedwith protected spindle and guide waysguide ways adjustableJaw width mm = 125Clamping width mm = 160For pipe-_ inch = 1/4 - 3Weight kg = 9,3

Pos.No.: 14.

98 233 001 SARC Welder’s helmet, CE, EN 166with flap frame and notchmade of grey glass-reinforced polyamideHelmet includes variable headbandSize of glasses mm = 90x110Glasse DIN 9Weight kg = 0.610

12.00

Pos.No.: 15.

68 634 001 SARC Welding-handshield EN 175CE-Norm, straightSize of glass mm = 90 x 110with glassesWeight kg = 0.380

12.00

Pos.No.: 16.

68 616 006 SUniversal welding goggelsnylon frame, mount to EN 166/169with coloured oval lenses DIN 6Flap ear pieces. The lenses are fixedwith a screw in the middleWeight kg = 0.044

48.00

Pos.No.: 17.

68 667 005Welder’s protective glooves EN 388/EN 407/EN 1149/2 Cat. 2

60.00

temperature resistantspecial leatherSleeve length cm = 15Total length cm = 35

Pos.No.: 18.

68 678 003Welder’s apronrugged chrome-tanned leatherwith chest protection and strapLengthxWidthxThickness mm = 1000x800x2

12.00

Pos.No.: 19.

68 667 007 SWelder’s gaiters, with fastening beltsSplit-leatherheight 35 cmDelivered as pair

12.00

Pos.No.: 20.168 T 823000Digital car spotter 5500 plusCountry of origin : ItalyMains voltage V = 400Max. absorbed power kW = 11Rated power 50 % kW = 3Mins fuse A = 16Power factor cos. = 0.7Spot welding current max. A = 300Sec. no-load voltage V = 5.4duty cycle % = 3Spot Welding capacity mm = 1.5+1.5(Double sided)Dimensions mm = 390x260x225Weight kg = 31Supply with:1 Studder kit

2.00

Pos.No.: 20.2

68 T 801041Manual clamp "C" with cablesCountry of Origin: Italy

2.00

Pos.No.: 20.3

68 T 803002Trolley for car spotter 5500 PlusCountry of Origin: ItalyDimensions cm = 51x48x84Weight kg = 13.5

2.00

Pos.No.: 21.

32.O MAJOR/RCar body straightening set -Major R-on trolleyCountry of Origin: Italywith single stage hand lever hydraulicpump and thrust cylinder as per pictureCapacity to = 12Total length mm = 6500Weigth kg = 340Supply in sheet steel box

1.00

Pos.No.: 22.

32.O 101 TITANIKCountry of Origin: ItalyHand jack set for carbody shop, completewith all accessories.Capacity ton = 12Closed piston mm = 320Piston stroke mm = 160with trolley

2.00

Pos.No.: 23.

32.US.423N16Car body repair set, supplied in sheet steel caseCountry of Origin: Italycomprising:1 mallet1 hammer with flat round and curvedchisel heads

1 hammer with serrated round and flatsquare heads

1 rail shaped dolly1 heel shaped dolly1 convex shaped serrated dolly1 dolly with two convex heads1 hand dolly with convex round head

and peen1 "C" shaped dolly1 anvil shaped dolly1 double spoon with one flat blade

and a curved one1 double spoon with one curved blade

and a flat one1 facing narrow body spoon, long model1 hammer with a flat round head and

a straight ball peen1 adjustable file holder1 flat flexible fileDimensions of case mm = 600x270x130Weight kg = 28.8

6.00

Pos.No.: 25.

81 381 001Angle grinder BOSCH GWS 21-180 JHVfor roughing, cutting, grinding andbrushing. With start-current limitation

rough-/cutting wheel _ mm = 180rubber backing pad _ mm = 180cup brushes _ mm = 100cup grinding wheel _ mm = 110idle speed U/min = 8500nominal capacity W = 2100nominal output W = 1350

3.00

weight kg = 4.4 Accessories:grinding wheel guardflangeclamping nut2-pin flange nut spanneradditional handle

Pos.No.: 26.

28.K SET10Welding electrode dryer Typ SETcountry of Origin: GermanyportableCapacity:Contents 10 packages electrodesHousing with double walls and insulatedwith control lamp, which indicates, ifset drying temperature is reaced.Including 2 m cable and CEE plug

Internal dimensions:Height mm = 470Width mm = 240Depth mm = 240

Electrical Connection:230 V, 50 Hz5.5 ACapacity 1.2 kW

Control:"On-OFF" via Thermostat,steplessly adjustable from50 - 300 COuter Dimensions:Height mm = 690Width mm = 410Depth mm = 370Weight kg = 28

2.00

Pos.No.: 27.1

71 052 003 STool box, 5 partions, emptymade of sheet steel, with carryinghandle

1.00

Outer dimensions mm = 530x200x200Colour: blue

Pos.No.: 27.2.1

51 175 004 SDouble open-ended spannerDIN 3110,chrome-vanadium-steel, chrome plated15° angle opening on both sidesOpening mm = 8x9Length mm = 142

1.00

Pos.No.: 27.2.2


1.00

Pos.No.: 27.2.3


1.00

Pos.No.: 27.2.4


1.00

Pos.No.: 27.2.5 1.00


Pos.No.: 27.2.6


1.00

Pos.No.: 27.2.7


1.00

Pos.No.: 27.2.8


1.00

Pos.No.: 27.3.1

51 309 008 SDouble ended offset socket wrenchchrome platedSize mm = 8x8

1.00

Total length mm = 122

Pos.No.: 27.3.2

51 309 010 SDouble ended offset socket wrenchchrome platedSize mm = 10x10Total length mm = 133

1.00

Pos.No.: 27.3.3


1.00

Pos.No.: 27.3.4


1.00

Pos.No.: 27.3.5


1.00

Pos.No.: 27.3.6


1.00

Pos.No.: 27.3.7 1.00


Pos.No.: 27.3.8


1.00

Pos.No.: 27.4.1

51 276 002 SAdjustable wrench similar DIN 3117 Amade of chrome-vanadium-steel, galvan.Length mm = 203Clamping width max. mm = 24

1.00

Pos.No.: 27.4.2

51 276 004 SAdjustable wrench DIN 3117Length mm = 304Opening max. mm = 33

1.00

Pos.No.: 27.5

55 208 061 SScrew driver set DIN ISO 8764with black, hardened and magnetic tipChrome-Molybdän-SteelSlot screw drivers:3,0x75/4,0x80/5,5x125/6,5x150 mmPhillips recessed screwdrivers:PH0x75/PH1x80/PH2x100

1.00

Pos.No.: 27.6

61 180 002 SSlip joint water pump plierSpecial steel

1.00

with 5-fold adjustable grooved jointLength mm = 240

Pos.No.: 27.7

61 303 207 SDiagonal Cutting plier DIN 5238 ASpecial steel, chrome plate, polishedLength mm = 180

1.00

Pos.No.: 27.8

61 154 207 SCombination plier DIN 5244made of special steel, chrome plated,polishedLength mm = 180

1.00

Pos.No.: 27.9

36 604 011 SPocket tape rule, in plastic casewith retracting spring, yellow paintedtape with black-red mm/mm graduationtop/bottom, tape stop, end hookMeasuring length m = 2Tape width mm = 13

1.00

Pos.No.: 27.10

44 405 001Metal saw frame, similar to DIN 6473flat steel frame, wooden handleand sawbladeFor saw blade length mm = 300Frame cross section mm = 18x8

1.00

Pos.No.: 27.11

62 017 005Carpenter’s hammer, French shapeface and cross pein groundblack paintedwith ash-wood handlePein height mm = 28

1.00

Weight without handle kg = 0,625

Pos.No.: 27.12

61 757 005Flat chisel DIN 6453Chrome-vanadium-steel, paintedLength mm = 200Width of edge mm = 24Cross section mm = 23 x 13

1.00

Pos.No.: 27.13

65 402 019Oil squirt canwith zinc cast tankdouble action pump of brassCapacity l = 0,2Pipe length mm = 135

1.00

Pos.No.: 27.13.1

41 144 007Rasp, half-round DIN 7263 CCut = 2Cross section mm = 25.0 x 7.0Length mm = 250Supply without handle

1.00

Pos.No.: 27.13.2

42 268 006File handlehard wood, with pressed-in steel tubeFor file length mm = 200-300Handle length mm = 130

1.00

Pos.No.: 27.13.3

41 143 008Workshop file set 5-pcs.with plastic handlesin PVC-wallet comprising:1 Workshop file, flat1 Workshop file, round

1.00

1 Workshop file, half-round1 Workshop file, three-square1 workshop file, squareFile length mm = 250Cut = 2

Pos.No.: 28.

74 549 001 SClip Shelf system, completel galvanizedFrame made of posts, steel feet platescover plates, Frame traverses andframe diagonalesShelves adjustable in height consistingof square tube side railsDimengsions HxLxD mm = 1972x2180x500consisting of:3 pcs.Frames height mm = 1972x5006 pcs.Shelves S1 mm = 900x5007 pcs.Shelves S1 mm = 1200x5003 pcs.containers for shelf




1.00

Pos.No.: 29.1


1.00

Pos.No.: 29.2

94 SC 204020Container for deskmobile, with rollers 2 of it fixableDimensions mm = W420xD600xH537with two drawers

1.00

one drawer with hanging file basket

Pos.No.: 30


1.00

Pos.No.: 31.


12.00

Pos.No.: 32.


1.00

Pos.No.: 33.


1.00

Pos.No.: 34.

74 550 2 001 SCantilever Rack, double sided usable,for internal installation1 basic rack and 1 add-on rackHeight mm = 1750Depth mm = 500consisting of:

3 pcs. double sided usable columns1750x500 mm

1 pc. reinforcement 1000 mm1 pc. reinforcement 750 mm3 pack of anchor bolts18 pcs. cantilever arms T 500 mm,

40x40x2 mm with plastic coversArm capacity 149 kg

Total outer length mm = 1896Total outer depth mm = 1140Colour: RAL 5015

1.00

Pos.No.: 35.


1.00

Pos.No.: 36.

28.Z.TRG160Cell TRG for Storage of Pressure gascylinders acc.TRG 280 in and outside ofbuildingsOuter dim.WxDxH mm = 1050x400x2150Doors = Double wing doorCapacity up to 3x50 Ltr. cylindersTube outlets = 8Illustration is similarhowever for 3 cylinders.

2.00

Pos.No.: 37.

28.KF.SA50Steel cylinder, EMPTY, with cylinder capand valve acc. DIN 477for oxygenCharging pressure bar = 200Testing pressure bar = 300nominal contents cbm = 10.0outlet valve and coiled tubing connectionssuitable to connect up to two oxygen mani-folds

1.00

Pos.No.: 39.2

28.KF.SA50Steel cylinder, EMPTY, with cylinder capand valve acc. DIN 477for oxygenCharging pressure bar = 200Testing pressure bar = 300nominal contents cbm = 10.0

2.00


Pos.No.: 01.3.2

19 307 001Coolant concentrate Opta HE 500Application ratio 1:20Quantity ltr. = 5Supply in plastic container

2.00

Pos.No.: 2.0

84.D.LF350Surface Grinding Machine Model: LF 350Country of Origin: ItalyMax. grinding area mm = 155x360Rapid feed per turn ofhandwheel = 2Size of cup wheel mm = 200x78x78 mmDim. of abrasivesegments mm = 50x20x90Speed of spindle rpm = 2840Voltage V = 400

Hz = 50Motor power kW = 3Coolant pump cap. kW = 0.06Weight of machine kg = 550

2.00

Pos.No.: 02.1.1

84.D.LF3501Segment holder

2.00

Pos.No.: 02.1.2.

84.D.LF3502Segments mm = 50x20x90

2.00

Pos.No.: 03.2 2.00

89.KN.105295Set of clamping tools, 52-partsin sturdy metal sheet metal case24 pcs. stud screw for T-slots4 pcs. extension nuts6 pcs. stepped clamps6 pcs. T-slot nuts6 pcs. hexagon nuts, step blocks

Pos.No.: 03.3.2.


2.00

Pos.No.: 04.0

89.KN.362660Universal Milling Machine VHF 1Country of Origin: ChinaMax. drilling dia. in St. mm = 30Max. milling dia. in St. mm = 25Tapping up to M = 16Spindle taper ISO = 30No. of spindle speeds vert. = 8Spindle speed range min.-1 = 115-1750No. of spindle speedshorizontally = 9Spindle speed range min.-1 = 60-1350Throat spindle to base = 200-700Distance spindle nose totable mm = 0-380Table clamping area mm = 800x240X-travel mm = 370Y-travel mm = 170Z-travel mm = 340Sleeve stroke mm = 120Motor vertical kW = 1.5Motor horizontal kW = 1.5Dimensions LxWxH mm = 1280x1100x1920Weight kg = 970

Standard accessories:Vertical milling headDigital displayScalesClamping device in all 3 axis

2.00

Pos.No.: 04.1


2.00

Pos.No.: 04.2

89.KN.104918Swivelling Machine Vicemade of cast iron, hardened andprecisely ground steel jaws, base plateswivelling by 360° with 1° divisionJaw width mm = 125Jaw height mm = 40Clamping width mm = 125Height mm = 136dia. of swivellingbase plate mm = 187Weight kg = 24Parallelity mm = +/- 0.0025

2.00

Pos.No.: 04.3.1

89.KN.102985Coolant Attachmentretrofitable, unmountedVolume l = 4.5Motor V = 400

kW = 0.9with coolant container, flexible nozzlestop cock, 1,5 m coolant hose

2.00

Pos.No.: 04.3.2

19 307 001Coolant concentrate Opta HE 500Application ratio 1:20

2.00

Quantity ltr. = 5Supply in plastic container

Pos.No.: 05.03.2


2.00

Pos.No.: 06.0-06.7

90.SP.1651000Precision Center Lathe with pedal brake Model t999

.......Country of Origin: ItalyDistance between centers mm = 1000Center height mm = 160Max. dia. on guides mm = 320Max. dia. on carriage mm = 198Spindle MT = 58 Spindle speeds rpm = 70-2000Longitudinal feeds = 0.078-1.044Cross feeds = 0.022-0.298Metric threads TPI = 2 1/4 - 40Spindle bore mm = 21Sleeve stroke mm = 120Tailstock taper MT = 3Motor V = 400, 50 Hz

W = 1500Dimensions mm = 1980x750x1450Weight kg = 670

Standard Accessories:3+3 jaw self centering chuck dia. 160 mmDrill chuck, 3-16 mm4+4 independent jaw chuck dia. 200 mmReduction sleeve MT5/3Rotating tailstock MT 3Face plate dia. 250 mmSteady restFollow restLive center MT3Foot brakeAdjustable bed stop

1.00

Thread dialLeadscrew hoodChuck safeguardFull length splash guardTOAB quick change toolpost with 5 toolholdersMachine lampElectric coolant attachment5 l emulsive coolant concentrate

Pos.No.: 07.0

89.MO.1000Universal Milling Machine Model FU0E

.......Country of Origin: ItalyTable:Table surface mm = 1000x2253 T-slots mm = 14Traveres:Longitudinal mm = 700Cross mm = 210Vertical mm = 400

Spindle:Standard taper = ISO 4012 Spindle speeds rpm = 50-1700

Automatic feeds on longitudinaland transversalRapid feeds on longitudinal

Electric motors:Main motor kW = 1.5

Net weight kg = 950

Standard accessories:acc. to CE rulescentralized lubrication forways by manual pumpCutter arbor with fixing tie rodand relative support restSet of service wrenchesInstallation and maintenancebook with test certificatein English

1.00

Pos.No.: 07.1

89.MO.10001Illumination system

1.00

Pos.No.: 07.2


1.00

Pos.No.: 07.3

89.MO.10002Rotating vice, opening 100 mm

1.00

Pos.No.: 07.4

89.MO.10003Boring head manual type, cap. 200 mmcomplete with one set ot tools

1.00

Pos.No.: 07.5


1.00

Pos.No.: 07.6

89.MO.10004Universal Milling head "Huron" typeISO 40 with support arm

1.00

Pos.No.: 07.7

89.MO.10005Collet chuck ISO 40 complete with one

1.00

set of 18 collets from 3 to 20 mmin box

Pos.No.: 07.8

89.KN.103900Shell end mill arborISO 40Arbor dia. mm = 22Draw in thread M = 16

1.00

Pos.No.: 07.9

89.MO.10006Cutter arbor ISO 40 dia. 27 mm

1.00

Pos.No.: 09.

80.KN.152796Horizontal Band Saw HB 250 ACountry of Origin: ChinaCutting capacity 90°:- round mm = 225- rectangular mm = 245x180Cutting capacity 60°:- round mm = 100- rectangular mm = 100x100Cutting capacity 45°:- round mm = 160- rectangular mm = 160x160Main motor kW = 1.1

V = 4002 Cutting speedsm/min. = 45/90Angle cuts = 0-60°Saw band dim. mm = 2480x27x0.9Weight kg = 200DimensionsLxWxH mm = 1380x580x930

Standard Accessories:Saw bow made of grey cast ironSaw bow feed adjustable viahydraulic cylinderMachine vice with quick clamping

2.00

functionSturdy saw blade guiding, adjustableGauge for saw blade tensionCoolant deviceLongitudinal stop

Pos.No.: 09.1.1.

80.KN.119858Bi-Metal saw bandDimensions mm = 2480x27x0.9Teeth per inch = 3/4

6.00

Pos.No.: 09.1.2

80.KN.119859Bi-Metal saw bandDimensions mm = 2480x27x0.9Teeth per inch = 4/6

6.00

Pos.No.: 09.2

80.KN.152871Roller Track, Loader SideLength mm = 2000Distance mm = 280No. of legs = 4Max. load cap. kg = 1200

2.00

Pos.No.: 06.

13.O 153Manual lever hydraulic workshop-pressModel 153-welded press H-fram of section steel-heigth adjustable worktable-two speed manual lever hydraulic pumpwith automatic ram return

Capacity to = 10Stroke max. mm = 350Clear heigth max. = 350Clear width mm = 520Clear widthbetween column mm = 120Supply with:

1.00

1 Pressure plate6 Mandrel _ mm = 16-18-20-22-25-302 V-blocksDimensions hxwxd: 1210x910x500 mmWeight: 104 kg

Pos.No.: 10.1


6.00

Pos.No.: 10.2


6.00

Pos.No.: 10.3

66 136 007Parallel-vicemilled clamping jaws, surface hardenedmade of steel, die forgedwith protected spindle and guide waysguide ways adjustableJaw width mm = 125Clamping width mm = 160For pipe-_ inch = 1/4 - 3Weight kg = 9,3

6.00

Pos.No.: 11.

73 376 002Drawer tool cabinet with 7 drawersmade of welded fine gauge sheet steelconstruction, with central lockingwith cylinder lock and two keys,drawers running of each 4 ball bearingswith safety pull-out interlock, withhandle ledge with marking strips and endcapsExternal dimensions mm = 1000x717x725Effective drawer area mm = 612x612Load bearing capacityper drawer kg = 1002 Drawer, height mm = 751 Drawer, height mm = 1003 Drawer, height mm = 1501 Drawer, heigth mm = 200

Colour RAL 6011, green

10.00

Pos.No.: 13.74 549 001 SClip Shelf system, completel galvanizedFrame made of posts, steel feet platescover plates, Frame traverses andframe diagonalesShelves adjustable in height consistingof square tube side railsDimengsions HxLxD mm = 1972x2180x500consisting of:3 pcs.Frames height mm = 1972x5006 pcs.Shelves S1 mm = 900x5007 pcs.Shelves S1 mm = 1200x5003 pcs.containers for shelf




1.00

Pos.No.: 13.

74 550 2 001 SCantilever Rack, double sided usable,for internal installation1 basic rack and 1 add-on rackHeight mm = 1750Depth mm = 500consisting of:3 pcs. double sided usable columns

1750x500 mm1 pc. reinforcement 1000 mm1 pc. reinforcement 750 mm3 pack of anchor bolts18 pcs. cantilever arms T 500 mm,

40x40x2 mm with plastic coversArm capacity 149 kg

Total outer length mm = 1896Total outer depth mm = 1140Colour: RAL 5015

1.00

Pos.No.: 14.

84.KN.102880Single Lip GrinderCountry of Origin: ItalyMax. collet dia. mm = 18Max. grinding dia. mm = 25Taper grinding = 0-180°Rear Angle = 0-45Speed min.-1 = 5200Cup wheel mm = 100x50x20Travel of toolholder mm = 140Motor W = 180

V = 400Weight kg = 45Dimension mm = 450x400x350

Standard Accessories:1 base cabinet1 dressing tool1 wheel mountcollets 3, 4, 6, 8 and 10 mmOperating tools

1.00

Instruction manual

Pos.No.: 14.1

84.KN.102875Cup Grinding WheelDimension mm = 100x50x20

2.00

Pos.No.: 15.

35 305 400400SSurface plateGrade I to DIN 876Surface finely scraped and finishedin ribbed designMaterial: special, altered cast ironDimensions L x W mm = 400 x 400Plate thickness mm = 15Rip height mm = 45Weight kg = 20

2.00

Pos.No.: 16.

35 328 001Scraping fluid sprayColour: bluetin ml = 300

2.00

Pos.No.: 17.

35 332 001Scraping-fluid cleanerQuantity ml = 300Supply spray-tin

2.00

Pos.No.: 18.

32 200 001Precision scribing and inspection gaugeaccuracy to DIN 862vernier and measuring rod dull chromedwith fine adjustment, locking srew andreading lensslide and scriber holder in one piecelongitudinal base stand with flat faceScriber carbide tippedRange mm = 0-300Reading mm/inch = 0,02Supply with one off-setcarbide tipped scriber

2.00

Pos.No.: 19.

33 729 013 SMeasuring stand with magnetic basewith fine adjustment,with prismatic baseOverall height mm = 176Cross arm length mm = 150for dials shank-_ mm = 8Base dimensions LxWxH mm = 50x55x63Magnetic force kg = 60Supply without dial gauge

2.00

Pos.No.: 20.

32 180 001 SPrecision dial indicator DIN 878metal casing, dull chromedwith vertical lug back.Graduation mm = 0,01Range mm = 0-10Diameter of case mm = 58Skale reading mm = 0-100Clamping shank-_ mm = 8 h6One pointer revolution mm = 1Number of pointer = 2

2.00

Pos.No.: 21. 2.00

36 112 003Back square DIN 875/IMaterial: special steel, not hardenedmeasuring edges and flat faces precisionground and adjustedSize mm = 150 x 100Cross section mm = 25 x 5

Pos.No.: 22

35 210 7575SV-blocks, pair, DIN 876/1made from special steel, numbered inpairs, 4 angle grooves 90°, accuracy 1Length x Width x Height mm = 75x75x50for shaft dia. mm = 5-50

2.00

Pos.No.: 23.

32 090 0031SPrecision vernier caliper DIN 862with depth measuring rod and cross-overjaws and bevelled jaw endswith locking screwstainless steel, fully hardendmeasuring faces lappedscale and vernier dull-chromedVernier lower mm = 0.02

upper inch = 1/1000Range mm = 200Jaw length mm = 50

12.00

Pos.No.: 24.

32 140 003Precision micrometer DIN 863, part 1with carbide measuring facehardened spindle, thread groundRange mm = 25-50Spindle diameter mm = 6,5Thread pitch of spindle mm = 0,5Thimble diameter mm = 18,0Reading mm = 0,01

12.00

Sleeve and thimble dull-chromedwith locking lever and ratchedwith insulating sleevesSupply in case

Pos.No.: 25.1


1.00

Pos.No.: 25.2

94 SC 204020Container for deskmobile, with rollers 2 of it fixableDimensions mm = W420xD600xH537with two drawersone drawer with hanging file basketcolour light grey RAL 7035

1.00

Pos.No.: 26.


1.00

Pos.No.: 27.


6.00

Pos.No.: 28.


1.00

Pos.No.: 30.

64 072 002Spiral-air pressure hosepolyamide, with quick-action couplingand nozzleMax. working pressure bar = 8Max. working length m = 2.5Length of hose m = 5Hose dimensions mm = 6 x 8

12.00

Pos.No.: 31.

63 226 001Air-cleaning gunmade of anodized aluminiumMax. air pressure bar = 4-6Nozzle diameter mm = 1,5_ of hose sleeve mm = 6,0Internal thread G = 3/8"

12.00

Pos.No.: 32.

17 JD AL16-3External threading tool holderSection mm = 16x16Length mm = 100Head length mm = 22

4.00

Pos.No.: 33.

17 JD 16ERISO1.0Throw-away tips16 ER-V-ISO 1.0

5.00

Pos.No.: 34.

17 JD 16ERISO1.5Throw-away tips16 ER-V-ISO 1.5

5.00

Pos.No.: 35.

17 501 PCLNR1616Toolholder 95°, for external turningType PCLNR, rightfor square throwaway tipswith toggle clamping PShank section HxB mm = 16x16Length mm = 100

2.00

Pos.No.: 36.

17 551 117Throw away tip CNMG 120408 M12Quality 6630, P 15 - 35Price per piecePacking unit = 10 pieces

10.00

Pos.No.: 37.

18 205 001Parting-off tool holderSize A00with clamping jaw and boltShank height mm = 16Shank width mm = 11Total length mm = 100Cutting edge height mm = 12

2.00

Pos.No.: 38.

18 208 001

5.00

Parting-off bladeSize A00-FMaterial: HSS-Co5Height mm = 8Width mm = 2,2Total length mm = 75

Pos.No.: 39.

17 521 A16M SCLCToolholder, for internal turningType SCLCR 09, rightShank-_ mm = 16Length mm = 150

2.00

Pos.No.: 40.

17 551 CCMT09T3Throw away tips CCMT 09 T3 08 - M12Price per piecePacking unit = 10 pieces

10.00

Pos.No.: 41.

18 547 003 SCranked carbide tipped turning toolISO 2 DIN 4972, right-hand cuttingMaterial: HM Quality P25/30Shank cross section mm = 16x16total lenght mm = 110ISO tool tip DIN 4950 C16

5.00

Pos.No.: 42.

18 661 003 SOffset carbide knife turning toolISO 6 DIN 4980, right-hand cuttingMaterial: HM Quality P 25/30Shank cross section mm = 16x16Total length mm = 110ISO tool tip DIN 4950 A8

5.00

Pos.No.: 43.

18 567 004 S

5.00

Carbide tipped square nose boring toolISO 9 DIN 4974, right-hand cuttingMaterial: HM Quality P 25/30Shank cross section mm = 16x16Total lenght mm = 210for minimum bore- _ mm = 27ISO tool tip DIN 4950 A 10

Pos.No.: 44.

18 634 003 SCranked carbide tipped turning toolISO 3 DIN 4978, right-hand cuttingMaterial: HM Quality P 25/30Shank cross section mm = 16x10Total lenght mm = 110ISO tool tip DIN 4950 A8

5.00

Pos.No.: 45.

18 687 002P30Carbide tipped parting-off toolISO 7 DIN 4981, right-hand cuttingMaterial: HM Quality P25/30Shank cross section mm = 16x10Total length mm = 110Recessing width mm = 4ISO tool tip DIN 4950 D4

5.00

Pos.No.: 46.

18 724 003Carbide tipped external thread turningtool, 60°, right-hand cuttingMaterial: HM Quality P 20Shank cross section mm = 16x10Total length mm = 120ISO tool tip DIN 4950 E6

5.00

Pos.No.: 47.

11 206 008Centre drill DIN 333 Form A, HSSD1=3,15 D2= 8,00 L=50,0

20.00

Pos.No.: 48.

11 109 025Set of twist drills, short,DIN 338 Typ NComprising twist drills Nr. 11 411 ...Diameter from 1,0 - 13,0 mm25 pieces mounting in steps of 0,5 mmStraight shank, right-hand cuttingFlut: groundPoint angle: 118 °Material: HSSSupply with sheet-metal box

10.00

Pos.No.: 49.

16 179 002Shell end mill DIN 1880, Type NR, HSSED1= 50 b=36 d2=22 z= 8

4.00

Pos.No.: 50.

16 188 001Shell end mill DIN 841 Type NR, HSSED1= 50 b=50 d2=22 z= 8

4.00

Pos.No.: 51.

16 696 112Slotting end mill DIN 327 D, Type ND1= 4,0 L1= 7 L2= 51 D2= 6 z=2

4.00

Pos.No.: 52.

16 696 120Slotting end mill DIN 327 D, Type ND1= 6,0 L1= 8 L2= 52 D2= 6 z=2

4.00

Pos.No.: 53.

16 712 112Ball nose end mill DIN 327, shortD1= 4,0 R= 2,0 L1= 7 L2= 51 D2= 6 z=2

4.00

Pos.No.: 54. 4.00

16 712 128Ball nose end mill DIN 327, shortD1= 8,0 R= 4,0 L1=11 L2= 61 D2=10 z=2

Pos.No.: 55.

16 716 250T-Slot milling cutter DIN 851 B, Type ND1=16,0 B= 8 T= 8 D2=10,0 L=62 z=6

4.00

Pos.No.: 56.

16 716 255T-Slot milling cutter DIN 851 B, Type ND1=22,0 B=10 T=12 D2=12,0 L=75 z=8

4.00

Pos.No.: 57.

16 164 040Side milling cutter DIN 885 Type H HSSCoD1= 63 b= 6 d2=22 z=16

4.00

Pos.No.: 58.

16 164 045Side milling cutter DIN 885 Type H HSSCoD1= 63 b= 8 d2=22 z=16

4.00

Pos.No.: 59.

16 164 050Side milling cutter DIN 885 Type H HSSCoD1= 63 b=10 d2=22 z=16

4.00

Pos.No.: 60.


1.00

Pos.No.: 61.


1.00

06 Electric Motor Rewinding Workshop


Pos.No.: 07.0

01.US.496IAssortment of tools for electrotechnicscomprising 57 pcs.plus electrotechnics maintenance casemade of leather

1.00

Pos.No.: 07.1

01.US.630ENTool bag, plastic, for electrotechnicscomprising 17 pcs. Tools

6.00

Pos.No.: 08.0x

03.EM.ASBLWinding Machine, manual Model 03.EM ASBLCountry of Origin: ItalyFor layer windings and electric motorcoils - without automatic wire guideComplete frame of aluminiumDimensions mm = 57x460x580Weight kg = 10Standard Accessories:1 rectangular faceplate 285 mm2 pairs of straight arbors dia. 40/80 mm1 pair of square mandrel1 Bobbin holder mod. TNfor wires dia. 0.10+0.40

1 Column for bobbin holder1 spindle 1 + 10 mm1 winding shaft dia. 10 mm1 simple mechanical revolution counter

with 5 figures1 Aluminium baseRAL 5015

4.00

Pos.No.: 08.1

03.EM.ZV1Radial vice ZV1Country of Origin: ItalyWorking dia. mm = 320Lifting power kg = 96Height mm = 500Width mm = 130Weight kg = 10

4.00

Pos.No.: 08.2

03.MA.08.2Basic Kit for Motor Coiling and Assembl-ing complete with set of enamelledcopper wire

4.00

Pos.No.: 08.3

03.MA.08.3Basic Kit for Motor Coiling and Assembl-ing complete with set of enamelledcopper wire

4.00

Pos.No.: 08.4

03.MA.08.4Motor Rewinding Tool Setfor Traineesin metal box

4.00

Pos.No.: 09.0x

03.EM.GM500Winding Machine Model GM500Country of Origin: ItalyFor electric motor coils up to 50 HpComplete frame of aluminiumElectronic speed variatorWinding speed rpm = 0-900Power supply V = 1x230,50/60 Hz,1 kWDimensions mm = 830x810x1490h1 faceplate 500 mm6 pairs of straight arbors

1.00

dia. 40/60/80/100/120/150 mm5 pairs of concentric arbors

dia. 10/15/20/25/301 pair of square mandrels1 starting foot pedal1 digital inverter1 digital revolution counter withdouble preset: slow-down + end

1 self braking motor1 table with drawer1 safety guard CE1 Instruction manual

Pos.No.: 09.1x

03.EM.SVM2Bobbin holder Model SVM2/MCountry of Origine: Italysuitable to unwind 2 bobbins simultan-eously. The wire stretching is adjust-able by handwheel that acts on a pliersbrake.Bobbin dimensions dia. mm = 650x300Lifting power kg = 200Dimensions mm = 1130x820x970Weight kg = 109

Standard Accessories:2 shafts dia. 25 mm

1.00

Documents

· PDF fileWelding Protection Screen with curtain ... Strip light on ceiling with 2 lightening tubes. ... Excentric Orbital Sander