Upload
lucscurtu
View
215
Download
2
Embed Size (px)
DESCRIPTION
Enclosed Wet Brake
Citation preview
COOLANT
FLOW
Enclosed Wet Brake
• Longer wearing friction material• Higher speeds• Greater Productivity• Proven lower drag than competition• Less drain on batteries• Less self generated heat• Meets OEM specifications• Employee company• Brakes shipped from inventory• Rebuilding service• 35 years in the coal market
+1 330 239 4933 • www.pttech.com
Enclosed Parking/Service Brake for Mining Equipment
*Note: Torque values will be adversely affected byhydraulic oils with friction modifiers or EP additives.
Service Brake Torque* 1,200 lb-inper 100 psi
Parking Brake Torque# 13,000 lb-inMax. ServiceBrake Pressure 1,400 psi
275 psiMin. Parking BrakeRelease PressureMax. Parking BrakeRelease Pressure 2,200 psi
RecommendedHydrualic Fluid 30 wt.
PT Tech’s A+ Hydraulic Brake continues to outperform the competition. Since its introduction in 1999, this wet brake has come to be known as “The Brake That Lasts”. Its through shaft cooling dramatically increases its survivability. Through experience gained on other brake designs and in-house testing PT Tech quantified the difference between brakes with and without through shaft cooling.
This single brake performs two distinct functions: a spring-set Parking Brake and a master cylinder operated Service Brake for underground mining vehicles.
Mining Applications: • Continuous Miners • Shuttle Cars • Longwall Shearers • Roadheaders • Chain Tensioners
Performance
F
F
5.99
3.07
Ø 11-1/2
Ø 5.9995.998
4.66ENGAGEMENT
LENGTH
.50
EXTERNAL SPLINE, FLAT ROOT SIDE FIT CLASS 5, DIAMETRAL PITCH 12/24,PRESSURE ANGLE 30°, NO. OF TEETH 20,PITCH DIA 1.6666.
WEAR INDICATOR(WHEN FLUSH REBUILD BRAKE).
WARNING: DO NOT OPERATEIF PIN IS FLUSH OR RECESSED.
Directly Replaces Ausco® On Mining Vehicles• Thru Shaft Cooling• Increase Braking Torque
PARKING BRAKE INLETS3/8" O-RING(9/16 -18 UNF -2B)
SERVICE BRAKE INLET1/4" O-RING(7/16 -20 UNF -2B)
PARKING BRAKEBLEEDER PORTSERVICE BRAKE
BLEEDER PORT
HYDRAULIC COOLANT EXIT
WEAR INDICATOR
PARKING BRAKE INLETS
SECTION F-F
MOUNTING BOLTSØ 1/2 HEX HEAD BOLTSUPPLIED BY CUSTOMER4 EQUALLY SPACED LOCATEDON A 10.000 B.C.
M10 X 1.5 -6H X 1/2 DEEP2 AT 180° ON A .875 B.C.
3/8 -16 UNC X 3/4 DEEP2 AT 180° ON A .875 B.C.
HYDRAULIC COOLANT INLET(3/4 SAE O-RING TUBEFITTING 1-1/16 -12THREAD).
HYDRAULIC COOLANT EXIT(1-1/16 -12 UNF-2B THREAD).
HYDRAULIC COOLANT INLETFOR THRU SHAFT COOLING
PTT-381-0 Complete Brake AssemblyPTT-381-60 Bearing & Seal Repair Kit PTT-381-61 Replacement Disk PackPTT-381-08 Replacement ShaftPTT-381-64 Hardware KitPTT-381-65 Compression Plate KitPTT-381-66 Wear Indicator KitPTT-381-67 Spring Kit
Spare Parts KitsService Brake Torque* 1,200 lb-in per 100 psiParking Brake Torque# 13,000 lb-inMax. Service Brake Pressure 1,400 psiMin. Parking Brake Release Pressure 275 psiMax. Parking Brake Release Pressure 2,200 psiRecommended Hydraulic Fluid 30 wt.
Performance Data
* NOTE: Torque values will be adversely affected by hydraulic oils with friction modifiers or EP additives.
1441 Wolf Creek Trail • P.O. Box 305Sharon Center, OH 44274-0305 USA330-239-4933 • fax 330-239-2012 • www.pttech.com
1/2013* Brochure content subject to change without notice.
PT Tech is a subsidiary of
ISO 2001:2008with design