R

Professional Grade Epoxy Coating

Tech Sheet

SEVENTY LLC 900 NW 33RD STPompano Beach, FL 33069- US T +1 (561)908-0697 T +1 (954)933-2500E info@seventyusa.netW seventyusa.net

CERTIFIED

CERTIFIED

CERTIFIED

ASSO

CIA

TED

V 04/2017 - P 1/2

POSE INSTRUCTIONSAPPLICATION Applied by ways of a roller, brush or spray,

through the use of airless pumping systems with compression rates >20:1. Over varni-shability intervals set between 12 and 36 hours. Anything beyond this limit wouldrequire proper F Additive sanding.Do not apply with temperatures below 5°C.

ROLLER High quality rollers only.

PENNELLO To be used in small areas or for small repair works. We recommend the use of professio-nal grade brushes only.

MIXING AND DILUTIONMIXING Mechanically mix component A, B and the

colorant paste (comp.C) separately.Subsequently, pour the colorant C paste in the Part A container, paying close attention to pick up any residual traces; part A and C must be perfectly mixed. Ultimately, slowly pour part B in the colored part A container. Mixing will be complete after about 2 minu-tes of agitation and, in any case, whenever the final mix reached chromatic homoge-neity. We suggest using the product’s full content and not partially.

MIX RATIO In weight:Part A (base): 80%Part B (hardener): 20%

DILUTION Typically not required

POT LIFE 4 hrs at 20° CLess at higher temperatures. Pot-life ends whenever the product loses its body and begins to thicken

GENERALITIES AND TECHNICAL DATATYPE Epoxy Resin Protective Coating.

FEATURES Liquid state application, solvent based epoxy resin protective coating formula.

CARACHTERISTICS Industrial grade Epoxy resin film coating, particularly indicated in anti carbonation floor coatings (bridges, viaducts, sports cen-ters, etc.) in general concrete installments. Also used as covering layer in anti corrosive cycles in steel manufacturing.

COLOR Neutral.

TINT Color chart.Supplied separately as C attachment.

APPEARANCE Clear.

SUBSTRATE Can be used in either pre treated resin sur-faces or in already water or solvent based epoxy or polyurethane primer floorings.

FINISH Typically not required.

COVERAGE One or two 150-200 g/mq single ayers usual-ly recommended, corresponding to a dry thickness of 60-80 μm.

SOLID CONT. in weight: 64 % (± 1)in volume: 48 % (± 1)

NOMINAL YIELD 4-5 mq/kg.In estimating the necessary material quanti-ties one must also consider all potential wa-ste often generated in both the mixing and pose phases.

VOC Of supply: ~ 110 g/lColorato (10% in weight): 110 g/lThese are nominal values and might slightly differ based on color type.

SCREED PREPARATIONGENERALITIES All treated surfaces must be clean, oil, grea-

se and chemical free and in perfect structu-ral conditions. This includes floor evenness and maintenance. Should any of the above requirements not be met, consequent soil in-terventions would then be necessary.

NOVOPOX 72 S

Film

Primer

Concrete support

*All communication generated by Seventy Srl, whether in print, via qualified and/or delegated personnel or through any other tangible or intangible means, having the sole scope of conveying information on the correct use and installation of its full range of products, notwithstanding their accuracy and full completeness, it won’t ever be used, under any circumstances, as grounds for legal litigations against Seventy or any of its employees and associates.This is more so in consideration of several other external factors objectively beyond the control and jurisdiction of Seventy Srl itself.These include, but are not limited to: installations carried out by personnel other than Seventy’s, peculiar adverse pose conditions and other relevant material factors.In lieu of the considerable percentage of unpredictable events negatively affecting pose, it is therefore recommended for all of our clients investigate, through a thorough profiling of tangible evidence, the correct product adequacy and needed quantities prior to purchase.

R

Professional Grade Epoxy Coating

Tech Sheet

V 04/2017 - P 2/2SEVENTY LLC 900 NW 33RD STPompano Beach, FL 33069- US T +1 (561)908-0697 T +1 (954)933-2500E info@seventyusa.netW seventyusa.net

CERTIFIED

CERTIFIED

CERTIFIED

ASSO

CIA

TED

STANDARD BOX AND STORAGEBOX 16 kg – 8 kg Base

4 kg – 2 kg Hardener

STORAGE Store all sealed boxes away from direct sunlight and in covered, dry and cool areas.

TEMPERATURES 4 – 40 °C

RH% 0 – 90 %

SHELF LIFE 6 months

CLEANING AND SAFETYCLEANING Only use idoneous diluents. In the event of

spilling, dispose according to local rules and regulations.

SAFETY Carefully read all precautions .

VENTILATION System ventilation must allow solvent con-centration to be maintained below explo-sion limits. All personnel must also be equip-ped with proper respirators.

PRECAUTIONS All electrical installations must be grounded. In explosion hazardous areas, operators must utilise non metal tools and anti spark shoes.

TECHABRASION RES. 20mg (TABER Test 1.000 rpm/1.000 g /grind-

stone CS 10)

HARDNESS Bucholz: 100 Pencil: 4 H

ADHERENCE > 3 MPa (on concrete)

POSE REQUIREMENTSApply exclusively with temperatures of at least 5°C above Dew-Point.

CURING TIMESTEMP. E RH 65% 20 °C

DUST OUT 40 min

DRY ON TOUCH 4 h

WALKABILITY 36 h

CARRIAGE ALBLE 72 h

Insufficient ventilation or low temperature conditions will require hi-gher times of polymerization and might cause trapping of solvents. As a result, premature coating deterioration might occur.

Excessive surface humidity or condensation during polymerization will severely hinder the cross-linking process and must then be avoided.

Should covering time be exceeded, surface will need to be mechani-cally sanded before applying any additional layers.

NOVOPOX 72 S