RB Scott Company, Inc.P.O Box 65Eau Claire, WI 54702-0065www.rbscott.com715-832-9792 (phone)715-832-7767 (fax)

GreyHawk/Metso C116 Portable Jaw Crusher

#1016/35900/HRC10014

Nordberg C116 Jaw Crusher

The Nordberg C116 is an efficient primary jaw crusher for quarries, gravel pits, mines andrecycling.

Mounting of the crusher is made without a bolted connection to the foundation. The main frame ofthe crusher is made of rolled steel side plates and two steel castings, connected throughprecision machined bosses and held together by large diameter bolts. The pitman and the frontand rear frame castings are made from high–quality steel with excellent fatigue strength. Thereare no welded joints in the frame. The frame can be completely disassembled for transportation ifnecessary. The eccentric shaft bearings are long–life grease lubricated spherical roller bearingsand are all of the same size.

The discharge setting is easy to adjust either mechanically, or as an option remotely withhydraulics, by means of moving wedges. The toggle plate operates on a rocking principle withoutany lubrication and serves as an overload fuse.

The crusher's jaw dies are of high–manganese steel castings, and the cheek plates of highabrasive–resistant steel plate. The jaw dies can be reversed for maximum utilization. Tools forjaw die changes are included with the jaw crusher.

Hydraulic setting adjustment – Hydraulic Power Unit 480/115V/60HzJaw Profile 32" x 45"– Quarry, protection plate – front frame & pitmanSupport Brackets – Installation angle –6 degreesDrive on left side (viewed from the fixed jaw end)Flywheels – 9 x 8 V groovesMotor – 200HP, 1200RPM, 449T frameDrive Equipment – Integral motor support

GuardsFeed BoxConveyor Belt Protection

Metso 46" x 20' Vibrating Grizzly Feeder

14' Pan with replaceable 3/4" AR steel linersSix feet of panel cord grizzly (2 pcs 44.75" wide x 35.94" long x 2.75" thick and with4"openings 1/2" Quick Change AR side plate linersVL–11 Vibrator, oil lubricated with (2) eccentric shafts and (2) wide face4d helical gears (4–110mm, 23 series bearings)Mounted on steel coil springs at 0 degreesV–belt drive includes feeder sheave, motor sheave, and beltsV–belt guardHR style pivot–type motor baseMotor – 30HP, 1800RPM, 286T frame

GreyHawk 48" Undercrusher Conveyor

8" channel bridged truss design equipped with Superior 5" CEMA 'C' channel mount idlers,channel mount impact idlers under impact zone, Superior 16" x 51" vulcanized head pulley,XT45 Hubs, 4–17/16" shaft and 4–7/16" Pillow block bearings, WorldWide (2) 5–15 shaft mountreducer, WorldWide (2) 20 HP, 1800 RPM, TEFC drive motor sheaves, V–Belts and motor V–Belt guard, Superior 12" x 51" wing tail pulley, XT 35 Hubs, 3–17/16" shaft with Superiortelescoping tube takeup with 3–17/16" Pillowblock bearings, Superior 5" CEMA ‘C' return idlers,return roll guards, return belt plow, Superior live shaft belt alignment rubber disc rollers, skirtplates with skirtboard rubber, 3 ply 1/4" x 1/16" conveyor belting, and Superior Exterra beltscraper system. Hinged tail assembly with hydraulic raise and lower for maintenance access.

GreyHawk Heavy Duty Chassis

24" 84# Mainbeam with Quad–Axle Hutch Suspension 49.5 inch centers, equipped for semitrailer towing with 11:00 R 22.5 tires on Budd type wheels, air controlled brakes, fifth wheelkingpin, conveyor supports, travel lights, reflectors, mud flaps, and heavy duty removablebumper/light bar. Machinery platform with hand rails above the jaw crusher, and a largemachinery platform around the crusher. Heavy Duty 3/4" thick A–36 steel hopper with 1/2"AR400 plug weld steel liners. Heavy duty skid assembly for removal of the complete hopperassembly, by–pass chute with hydraulic slide arrangement for providing service access to theback of the jaw crusher.

Electric Starters, Wiring and Controls – 5' x 4' x 12" electrical enclosure with structural supportto set on grade during plant operation. The enclosure is connected to the plant with 15' electricalcable. The enclosure has a main inlet line surge arrestor, warning horn, lifting eyes and maincircuit breaker with door interlocked disconnect linkage. All on–plant equipment is controlled byNEMA rated starters that are mounted in a separate remote control panel. Crusher motor iscontrolled by a digital solid state reduce voltage starter (soft–start). All push buttons, pilot lightsand E–stop switches are heavy duty, 30mm, oil and dust tight devices, and includes an hour

meter located inside the enclosure and a door mounted amp meter for crusher amperage.

Adjustable king pin support – Adjustable tubular supports reduce the amount of blockingrequired in the kingpin area during plant operation, which simplifies set up and tear down. Thekingpin supports are lifted and pinned for towing to clear the semi–tractor.

Power hydraulic raise and lower – Six tube in tube style heavy duty run–on jacklegs, with 6"diameter x 18" stroke cylinders to lift the plant into the operating position. Each cylinder isindependently controlled from a hydraulic valve for precise control and ease of leveling. Thehydraulic system is powered by an 11 HP Honda gasoline engine with electric start and backuprecoil start. Includes two (2) additional valves for sliding the by–pass hopper away from the jawcrusher, and for hydraulic lowering the under crusher conveyor.