Slide 2 Relay Control Slide 3 Relay Control -- Introduction
Two-position control, using a digital (relay) output, is used to
turn something on and off. We use a differential and an offset to
tell an output when to open and close based on the control variable
and setpoint. Slide 4 Relay Control -- Definitions Differential
amount of change in the control variable from when the output turns
on to when it turns off Offset a value that creates a deadband for
a stage the first stage typically has an offset of 0 Slide 5
Offsets and Differentials, 2 Setpoints Slide 6 Offsets,
Differentials and Deadband, 1 Setpoint Used on the SZ1025b and
SZ1143b Slide 7 Proportional Control Slide 8 Proportional Control
-- Introduction Analog outputs are called modulating outputs. These
outputs vary based on how far the input is away from setpoint.
Modulating outputs provide tighter control than two position
outputs. Slide 9 Proportional Control -- Definitions Proportional
Control generates an output that is related to the distance between
the active setpoint and the input Proportional Band/Throttling
Range number of degrees (or percent of span) that the input must
change to drive the output from 0 to 100% (either 0 to 20 mA or 4
to 20 mA) Slide 10 Proportional Control -- Definitions Setpoint
Offset a value that creates a deadband before modulation starts
Aquastat allows the action to reverse when a digital input is made
(SZ1017a, SZ1018, SZ1143b, SZ1051) or an analog input exceeds a
certain value (SZ1025a, SZ1018, SZ1062, SZ1064) Slide 11
Proportional Control -- Definitions Direct Acting the output
increases as the input increases Reverse Acting the output
decreases as the input increases Slide 12 Direct Acting - Output
12mA @ Setpoint Slide 13 Reverse Acting - Output 12mA @ Setpoint
Slide 14 Direct Acting - Output 4 or 20mA @ Setpoint CoolingHeating
Slide 15 Reverse Acting - Output 4 or 20mA @ Setpoint
CoolingHeating Slide 16 Keypad Programming Slide 17 Thermostat
Keypad Layout Slide 18 SZ1060 Series Keypad Layout Slide 19
Comparison of Thermostat Keypads Typical Superstat KeypadSZ1060
Series Keypad Slide 20 SL1001a & SZ1140 Series Keypad Layout
Slide 21 Conventional Thermostats Menu-by-Menu Example Follow Along
Using Demo Panel Slides Printed in Handout Catalog Page 183 All
Thermostats Basically the Same Complete Sequences in Product
Manuals All Sequences in Product Catalog www.tcsbasys.com Slide 22
SZ-QD Trainer Demo Panel(SZ1031) 248 always works!!! Use down arrow
to get to 248 more quickly. Slide 23 SZ-QD Trainer Demo Panel
(SZ1031) -- continued Use your badge number as the address for your
stat. Slide 24 SZ-QD Trainer Demo Panel (SZ1031) -- continued Slide
25 Slide 26 This Screen is Repeated for Occupied Periods B, C, and
D Slide 27 SZ-QD Trainer Demo Panel (SZ1031) -- continued Slide 28
Model Specific Features SZ1035 Slide 29 Additional Model Specific
Features -- continued Slide 30 SZ-QD Trainer Demo Panel (SZ1031) --
continued Slide 31 Slide 32 Slide 33 Slide 34 Slide 35 Slide 36
Slide 37 Slide 38 NOTE: This is a secondary access code. Slide 39
Setting the Clock & Schedule (SZ1031) 248 always works!!! Use
down arrow to get to 248 more quickly. Slide 40 Setting the Clock
& Schedule (SZ1031) -- continued This Screen is Repeated for
Occupied Periods C and D Slide 41 Setting the Clock & Schedule
(SZ1031) -- continued These Screens are Repeated for Wed., Thurs.,
Fri., Sat., Sun., Plus Holiday #1 & #2. This Screen is Repeated
for Occupied Periods C and D Slide 42 Setting the Clock &
Schedule (SZ1031)-- continued Total Possible Holidays 2x 12 x 99 =
2,376 scheds. instances days days. Slide 43 Setting the Clock &
Schedule (SZ1031)-- continued Slide 44 Where to Get Help or Answers
Instructions Sent with Product TCS Basys Controls Catalog Training
& Reference Manual www.tcsbasys.com Call TCS Directly
800-288-9383 Slide 45 Software Programming Slide 46 PC Based
Software -- Revelation Professional Menu Driven Programming Use for
Network Setup & Testing, Commissioning, & Load Balancing
Read Before Making Changes Write Before Going to NEXT Menu Write
vs. Write Half / Write Page Load All & Save All Options *** NOT
SUPPORTED AS OF JAN 2009 *** Slide 47 Superstat conventional
heat/cool Rev Pro Manual pg C-9 Slide 48 Superstat conventional
heat/cool Rev Pro Manual pg C-9 Slide 49 Superstat conventional
heat/cool Rev Pro Manual pg C-9 Slide 50 PC Based Software --
Insight Similar to Revelation Professional Tab Driven Interface
Uses Same Datasheets as Ubiquity Use for Network Setup &
Testing, Commissioning, & Load Balancing Shows Current Values
(no read required) Write Page Before Going to New Tab *** NEW
SOLUTION AS OF JAN 2009 *** Slide 51 Superstat heat pump Slide 52
Slide 53 Slide 54 Slide 55 Slide 56 Slide 57 Internet Style
Software Ubiquity Similar to Revelation Professional Single Page
for All Programming Info Shows Current Values (no read required)
Writes All Values on Submit Read Controller Option (if needed)
Slide 58 Single Page Programming Screen Slide 59 General Info,
Alarms, & Assigned Assets Slide 60 Schedule Slide 61 Controller
Summary & Ubiquity Functions Slide 62 System and Setpoints
& Digital Inputs Slide 63 Digital Outputs Slide 64 Additional
Functions, Comments & Buttons Slide 65 Superstat heat
pumpSZ1033 Slide 66 Superstat with 1 analog outputSZ1017a Slide 67
Superstat with 1 analog outputSZ1041 Slide 68 Superstat with 2
analog outputsSZ1051 Slide 69 Superstat with 2 analog outputsSZ1053
Slide 70 General Purpose ControllerSZ1143b Slide 71 General Purpose
ControllerSZ1143b - contd Slide 72 General Purpose MonitorSZ1145
Slide 73 General Purpose MonitorSZ1145 - contd Slide 74 Slide 75
VAV Box ControllerSZ1025b Slide 76 VAV Box ControllerSZ1025b- contd
Slide 77 Slide 78 2 Channel, 365-Day Time ClockSL1001a Slide 79 2
Ch., 365-Day Time ClockSL1001a - contd Slide 80 Where to Get Help
or Answers Instructions Sent with Product TCS Basys Controls
Catalog Training & Reference Manual www.tcsbasys.com Call TCS
Directly 800-288-9383 Slide 81 Controller Wiring
