RXV2700

AV RECEIVER/AV AMPLIFIER

RX-V2700/DSP-AX2700SERVICE MANUALRX-V2700/ DSP-AX2700

IMPORTANT NOTICEThis manual has been provided for the use of authorized YAMAHA Retailers and their service personnel. It has been assumed that basic service procedures inherent to the industry, and more specifically YAMAHA Products, are already known and understood by the users, and have therefore not been restated.

WARNING:

Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, destruction of expensive components, and failure of the product to perform as specified. For these reasons, we advise all YAMAHA product owners that any service required should be performed by an authorized YAMAHA Retailer or the appointed service representative. IMPORTANT: The presentation or sale of this manual to any individual or firm does not constitute authorization, certification or recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form. The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover. The research, engineering, and service departments of YAMAHA are continually striving to improve YAMAHA products. Modifications are, therefore, inevitable and specifications are subject to change without notice or obligation to retrofit. Should any discrepancy appear to exist, please contact the distributor's Service Division.

WARNING:

Static discharges can destroy expensive components. Discharge any static electricity your body may have accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss). IMPORTANT: Turn the unit OFF during disassembly and part replacement. Recheck all work before you apply power to the unit.

I CONTENTSTO SERVICE PERSONNEL .......................................... 2 FRONT PANELS ............................................................ 3 REAR PANELS .......................................................... 46 REMOTE CONTROL PANELS ...................................... 7 SPECIFICATIONS / .................................. 810 INTERNAL VIEW ......................................................... 11 DISASSEMBLY PROCEDURES / .......... 1217 UPDATING FIRMWARE / ..................................... 1819 SELF DIAGNOSIS FUNCTION (DIAG) / ..................................... 2055 AMP ADJUSTMENT / ........................... 56 DISPLAY DATA ........................................................... 57 IC DATA ................................................................. 5872 BLOCK DIAGRAMS .............................................. 7376 PIN CONNECTION DIAGRAMS ............................ 7779 PRINTED CIRCUIT BOARDS .............................. 80108 SCHEMATIC DIAGRAMS .................................. 109127 REPLACEMENT PARTS LIST .......................... 129166 REMOTE CONTROL .......................................... 167169 ADVANCED SETUP / ..... 170172

101023

2006 All rights reserved. This manual is copyrighted by YAMAHA and may not be copied or redistributed either in print or electronically without permission.

P.O.Box 1, Hamamatsu, Japan

'06.10

RX-V2700/DSP-AX2700

I TO SERVICE PERSONNEL1. Critical Components Information Components having special characteristics are marked s and must be replaced with parts having specifications equal to those originally installed. 2. Leakage Current Measurement (For 120V Models Only) When service has been completed, it is imperative to verify that all exposed conductive surfaces are properly insulated from supply circuits.RX-V2700/ DSP-AX2700G

WALL OUTLET

EQUIPMENT UNDER TEST

AC LEAKAGE TESTER OR EQUIVALENT

INSULATING TABLEG G

Meter impedance should be equivalent to 1500 ohms shunted by 0.15F.

Leakage current must not exceed 0.5mA. Be sure to test for leakage with the AC plug in both polarities.

For U model CAUTION F1, F2: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE 10A, 125V FUSE. For C model CAUTION F1, F2: REPLACE WITH SAME TYPE 10A, 125V FUSE. ATTENTION F1, F2: UTILISER UN FUSIBLE DE RECHANGE DE MME TYPE DE 10A, 125V.

WARNING: CHEMICAL CONTENT NOTICE!The solder used in the production of this product contains LEAD. In addition, other electrical/electronic and/or plastic (where applicable) components may also contain traces of chemicals found by the California Health and Welfare Agency (and possibly other entities) to cause cancer and/or birth defects or other reproductive harm. DO NOT PLACE SOLDER, ELECTRICAL/ELECTRONIC OR PLASTIC COMPONENTS IN YOUR MOUTH FOR ANY REASON WHATSOEVER! Avoid prolonged, unprotected contact between solder and your skin! When soldering, do not inhale solder fumes or expose eyes to solder/flux vapor! If you come in contact with solder or components located inside the enclosure of this product, wash your hands before handling food.

About lead free solder / All of the P.C.B.s installed in this unit and solder joints are soldered using the lead free solder. Among some types of lead free solder currently available, it is recommended to use one of the following types for the repair work. Sn + Ag + Cu (tin + silver + copper) Sn + Cu (tin + copper) Sn + Zn + Bi (tin + zinc + bismuth) Sn+Ag+Cu ++ Sn+Cu + Sn+Zn+Bi ++

Caution:As the melting point temperature of the lead free solder is about 30C to 40C (50F to 70F) higher than that of the lead solder, be sure to use a soldering iron suitable to each solder.

3040

2

RX-V2700/DSP-AX2700

I FRONT PANELSRX-V2700 (U, C models)

RX-V2700/ DSP-AX2700

RX-V2700 (R, T, K, A, B, G, E, L models)

DSP-AX2700 (J model)

3

RX-V2700/DSP-AX2700

I REAR PANELSRX-V2700 (U, C models)


RX-V2700 (R model)

RX-V2700 (T model)

4

RX-V2700/DSP-AX2700

RX-V2700 (K model)


RX-V2700 (A model)

RX-V2700 (B model)

5

RX-V2700/DSP-AX2700

RX-V2700 (G, E models)


RX-V2700 (L model)

DSP-AX2700 (J model)

6

RX-V2700/DSP-AX2700

I REMOTE CONTROL PANELS RAV363 RX-V2700 (U, C models) RXV362 RX-V2700 (R, T, K, A, B, G, E, L models) DSP-AX2700 (J model)


RAV25 RX-V2700 (U, C models)

RAV24 RX-V2700 (R, T, K, A, B, G, E, L models)

7

RX-V2700/DSP-AX2700

I SPECIFICATIONS / I Audio Section / Minimum RMS Output Power (Power Amp. Section) / () (20 Hz to 20 kHz) FRONT L/R U, C, R, T, K, A, B, G, E, L models (0.04 % THD, 8 ohms) ........................................................................................ 140 W + 140 W J model (0.06 % THD, 6 ohms) ............................ 140 W + 140 W CENTER U, C, R, T, K, A, B, G, E, L models (0.04 % THD, 8 ohms) .......................................................................................... 140 W J model (0.06 % THD, 6 ohms) .......................................... 140 W SURROUND L/R U, C, R, T, K, A, B, G, E, L models (0.04 % THD, 8 ohms) ........................................................................................ 140 W + 140 W J model (0.06 % THD, 6 ohms) ............................ 140 W + 140 W SURROUND BACK L/R U, C, R, T, K, A, B, G, E, L models (0.04 % THD, 8 ohms) ........................................................................................ 140 W + 140 W J model (0.06 % THD, 6 ohms) ............................ 140 W + 140 W Maximum Power / (JEITA, 1 kHz, 10 % THD) FRONT L/R R, T, K, L models (8 ohms) .................................. 185 W + 185 W J model (6 ohms) ................................................. 185 W + 185 W CENTER R, T, K, L models (8 ohms) ................................................. 185 W J model (6 ohms) ................................................................ 185 W SURROUND L/R R, T, K, L models (8 ohms) .................................. 185 W + 185 W J model (6 ohms) ................................................. 185 W + 185 W SURROUND BACK L/R R, T, K, L models (8 ohms) .................................. 185 W + 185 W J model (6 ohms) ................................................. 185 W + 185 W Dynamic Power Per Channel / (IHF) FRONT L/R (8/6/4/2 ohms) U, C, R, T, K, A, L models ............................. 170/205/265/345 W Max. Power Per Channel / Max. (1 kHz, 0.7 % THD, 4 ohms) [B, G, E models] FRONT L/R ............................................................. 200 W + 200 W CENTER ................................................................................ 200 W SURROUND L/R .................................................... 200 W + 200 W SURROUND BACK L/R ......................................... 200 W + 200 W Dynamic Headroom / U, C, R, T, K, A, L models (8 ohms) ................................... 0.84 dB IEC Power / IEC (1 kHz, 0.04 % THD, 8 ohms) [B, G, E models] FRONT L/R ............................................................. 145 W + 145 W Damping Factor / FRONT L/R (20 Hz to 20 kHz, SPEAKER-A, 8 ohms) ..... 150 or more Input Sensitivity/Input Impedance / / (1 kHz, 100 W/8 ohms) PHONO (MM) ................................................... 3.5 mV / 47 k-ohms CD, etc. ............................................................ 200 mV / 47 k-ohms MULTI CH INPUT FRONT L/R, CENTER, SURROUND L/R, SUBWOOFER .................................................................... 200 mV / 47 k-ohms Maximum Input Signal Level / PHONO (MM) (1 kHz, 0.1 % THD) .......................... 60 mV or more CD, etc. (1 kHz, 0.5 % THD) ...................................... 2.4 V or more Output Level/Output Impedance / / REC OUT .......................................................... 200 mV / 900 ohms PRE OUT (FRONT L/R, CENTER, SURROUND L/R, SURROUND BACK L/R) .................................. 1.0 V / 1.2 k-ohms SUBWOOFER (20 Hz) ....................................... 2.0 V / 1.2 k-ohms ZONE 2 OUT [U, C, R, T, K, A, B, G, E, L models] .......................................................................... 1.0 V / 1.4 k-ohms ZONE 3 OUT [U, C, R, T, K, A, B, G, E, L models] .......................................................................... 1.0 V / 1.4 k-ohms Headphone Jack Rated Output/Impedance / / CD, etc. (1 kHz, 40 mV, 8 ohms) ..................... 150 mV / 100 ohms Frequency Response / (10 Hz to 100 kHz) CD, etc. to FRONT L/R (Pure direct) .............................. +0/-3.0 dB RIAA Equalization Deviation / RIAA (20 Hz to 20 kHz) PHONO (MM) ................................................................... 0 0.5 dB Total Harmonic Distortion / (20 Hz to 20 kHz) PHONO (MM) to REC OUT (1 V) .............................. 0.02 % or less CD, etc. to FRONT L/R SP OUT (70 W, 8 ohms) ..... 0.04 % or less Signal to Noise Ratio / (IHF-A network) PHONO (MM) (Input shorted) to SP OUT U, C, R, T, K, L models (5 mV) ............................... 86 dB or more A, B, G, E models (5 mV) ....................................... 81 dB or more J model (2.5 mV) ..................................................... 80 dB or more CD, etc. (Input shorted) to SP OUT 250 mV .................................................................. 100 dB or more Residual Noise / (IHF-A network) FRONT L/R, SP OUT ............................................... 150 V or less Channel Separation / (1 kHz/10 kHz) PHONO (Input shorted) ..................... 60 dB or more/55 dB or more CD, etc. (Input 5.1 k-ohms shorted) ... 60 dB or more/45 dB or more Tone Control Characteristics / BASS Boost/Cut ................................................................ 6 dB (50 Hz) Turnover frequency .............................................. 125/350/500 Hz TREBLE Boost/Cut .............................................................. 6 dB (20 kHz) Turnover frequency ............................................... 2.5/3.5/8.0 kHz ZONE2, ZONE3 Tone Control Characteristics [U, C, R, T, K, A, B, G, E, L models] BASS Boost/Cut ............................................................ 10 dB (100 Hz) Turnover frequency ............................................................ 450 Hz TREBLE Boost/Cut ............................................................ 10 dB (10 kHz) Turnover frequency ........................................................... 2.0 kHz Filter Characteristics / FRONT, CENTER, SURROUND, SURROUND BACK small (H.P.F.) ................... fc=40/60/80/90/100/110/120/160/200 Hz, 12 dB/oct. SUBWOOFER (L.P.F.) ................... fc=40/60/80/90/100/110/120/160/200 Hz, 24 dB/oct. I Video Section / Video Format / Monitor out (wall paper) / U, C, R, K, J models .................................................... NTSC/PAL T, A, B, G, E, L models ................................................ PAL/NTSC Video conversion ............................................................ NTSC/PAL Composite Video Signal Level / .............................................................................. 1 Vp-p / 75 ohms S-Video Signal Level / S Y ............................................................................ 1 Vp-p / 75 ohms C ..................................................................... 0.286 Vp-p / 75 ohms Component Video Signal Level / Y ............................................................................ 1 Vp-p / 75 ohms Pb/Pr .................................................................. 0.7 Vp-p / 75 ohms Maximum Input Level / VIDEO CONV. OFF .............................................. 1.5 Vp-p or more Signal to Noise Ratio / VIDEO CONV. OFF ................................................... 60 dB or more Monitor Out Frequency Response / (VIDEO CONV. OFF) Component video signal ............................ 5 Hz to 100 MHz, 3 dB D5-video signal [J model] .......................... 5 Hz to 100 MHz, 3 dB Video Format Zone out (gray back) U, C, R, K models ................................................................ NTSC T, A, B, G, E, L models ........................................................... PAL I FM Section / FM Tuning Range / U, C models ........................................................ 87.5 to 107.9 MHz R, L models ............................ 87.5 to 108.0 / 87.50 to 108.00 MHz T, K, A, B, G, E models .................................. 87.50 to 108.00 MHz J model ................................................................. 76.0 to 90.0 MHz 50dB Quieting Sensitivity / 50 dB SN (IHF) (1 kHz, 100 % MOD.) Mono / Stereo ......................... 2.0 V (17.3 dBf) / 25 V (39.2 dBf) Usable Sensitivity / (IHF) Mono ..................................................................... 1.0 V (11.2 dBf) Selectivity / at 400 kHz ............................................................................... 70 dB Signal to Noise Ratio / (IHF) Mono / Stereo ............................................................. 76 dB / 70 dB Harmonic Distortion / (1 kHz) Mono / Stereo ............................................................. 0.2 % / 0.3 % Stereo Separation / (1 kHz) ............ 42 dB Frequency Response / (20 Hz to 15 kHz) ..... +0.5 / -2 dB Antenna Input / ......................... 75 ohms unbalanced


8

RX-V2700/DSP-AX2700I AM Section / AM Tuning Range / U, C models .......................................................... 530 to 1,710 kHz R, L models ................................... 530 to 1,710 / 531 to 1,611 kHz T, K, A, B, G, E, J models .................................... 531 to 1,611 kHz Usable Sensitivity / ............................................ 300 V/m Antenna Input / .................................... Loop antenna I General / Power Supply / U, C models ........................................................... AC 120 V, 60 Hz R, L models .......................... AC 110/120/220/230-240 V, 50/60 Hz T model .................................................................. AC 220 V, 50 Hz K model .................................................................. AC 220 V, 60 Hz A model .................................................................. AC 240 V, 50 Hz B, G, E models ....................................................... AC 230 V, 50 Hz J model ............................................................ AC 100 V, 50/60 Hz Power Consumption / U, C models ............................................................ 500 W / 630 VA R, T, K, A, B, G, E, L models ................................................ 500 W J model .................................................................................. 400 W Standby Power Consumption (reference data) / () U, C, T, K, A, B, G, E, L, J models ............................. 0.1 W or less R model (AC 240 V / 50 Hz) ..................................... 0.33 W or less Maximum Power Consumption / (6ch drive, 10 % THD) R model ................................................................................ 1100 W AC Outlets / AC 2 switched outlets U, C models ........................... 100 W max. total / 0.8 A max. total R, T, L models ...................................................... 50 W max. total G, E models ........................... 100 W max. total / 0.4 A max. total J model ............................................................... 100 W max. total 1 switched outlet A model ...................................................................... 100 W max. B model .................................................. 100 W max. / 0.4 A max. Dimensions / (W x H x D) ......................... 435 x 171 x 438.5 mm (17-1/8" x 6-3/4" x 17-1/4") Weight / U, C, R, T, K, A, B, G, E, L models ............ 17.2 kg (37 lbs. 14 oz.) J model ......................................................... 18.3 kg (40 lbs. 5 oz.) Finish / Gold color .......................................................... R, T, K, L, J models Black color ................................................. U, C, R, A, G, E models Titanium color ........................................ C, T, K, B, G, E, L models Accessories / Remote control x 1, Zone remote control x 1 (U, C, R, T, K, A, B, G, E, L models), Batteries (UM-4E) x 6 (U, C, R, T, K, A, B, G, E, L models) / x 4 (J model), Indoor FM antenna x 1, AM loop antenna x 1, Power cable x 1 (U, C, R, T, K, A, B, G, E, J models) / x 2 (L model), Speaker terminal wrench x 1, Optimizer microphone x 1 * Specifications are subject to change without notice due to product improvements.

SOUND/SURROUND SELECT MENU

Room Size (0.1 to 2.0, 0.1 step)

Init. Delay (1 to 49 ms)


Liveness (0 to 10)

Liveness (0 to 10)

Direct (Auto/Off)

HDMIHDMIHigh-Definition Multimedia InterfaceHDMI Licensing LLC

CLASSICAL SILENT CINEMA is a trademark of YAMAHA CORPORATION./SILENT CINEMA

The XM name and related logos are registered trademarks of XM Satellite Radio Inc.

LIVE/CLUB

Neural Surround name and related logos are trademarks owned by Neural Audio Corporation.

ENTERTAINMENT

Circle Surround IIDialog ClarityTruBassSRS SRS Labs,Inc. Circle Surround IIDialog ClarityTruBassSRS Labs,Inc.

MOVIE

AAC

(7/8")

22

DIMENSIONS /

STEREO SUR. DECODE MUSIC ENHANCER

Hall in Munich Hall in Vienna Hall in Amsterdam Church in Freiburg Chamber Village Vanguard Warehouse Loft Cellar Club The Roxy Theatre The Bottom Line Sports Action Game Roleplaying Game Music Video Recital/Opera Standard Spectacle Sci-Fi Adventure Drama Mono Movie 2ch Stereo 7ch Stereo Surround Decoder 2ch Enhancer 7ch Enhancer

*1 *1 *1 *1 *1

O O O O O O O O O O O O O O O O O O O O O

O O O O O O O O O O O O O O O O O O O O

O O O

O O O O O O O O O O O O O O O

O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O

O O O O

O O O O

O O O O

O

O

O

O

O

O O O O O O O O O O O O O O O O O O O O O O O

*2

*3 *3 *3 *4 *5 *5 O O

438.5 (17-1/4")

*1 DECODE TYPE Pro Logic PLx MoviePL II x Neo:6 Cinema6

U .......... R .......... K .......... B .......... E .......... J ...........

U.S.A. model General model Korean model British model South European model Japanese model

C ...... Canadian model T ....... Chinese model A ...... Australian model G ...... European model L ....... Singapore model

394 (15-1/2")

*2 DECODE TYPE

Manufactured under license from Dolby Laboratories. Dolby, Pro Logic, and the double-D symbol are trademarks of Dolby Laboratories.

Unit: mm (inch)mm

150 (5-15/16")

171 (6-3/4")

Manufactured under license from Digital Theater Systems, Inc. DTS, DTS-ES, NEO:6, and DTS 96/24 are trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All right reserved.DTSDTS-ES Extended SurroundNeo6DTS 96/24

(7/8")

PRO LOGIC Surround EX D

Pro Logic PL II x MoviePL II x PL II x Music PL II x PL II x GamePL II x Neo:6 Cinema6 Neo:6 Music6 CS II CinemaCS II CS II MusicCS II neural surround

(J model) (J model) (U, C models)

22.5

*3 Setting is possible only when Pro Logic II x Music is selected using decode type. / Decode typePro Logic II x Music *4 Setting is possible only when Neo:6 Music is selected using decode type. / Decode typeNeo:6 Music *5 Setting is possible only when CS II Cinema/Music is selected using decode type. / Decode typeCS II Cinema/Music

iPodApple Computer,Inc.

21

435 (17-1/8")

(13/16")

iPod is a trademark of Apple Computer, Inc., registered in the U.S. and other countries.

Low/High

Surround

HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

TruBass (0 to 8)

FOCUS (0 to 8)

Surround Back

Panorama (Off/On)

Liveness (0 to 10)

This receiver supports network connections.Decode Type

Center Image (0.0 to 1.0, 0.1 step)

Rev. Time (1.0 to 5.0 s, 0.1 step)


MPEG Layer3Fraunhofer IISThomson

CT/SL/SR/SB/PL/PR Level (0 to 100 %)

MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.


Dimension (-3 to STD to +3)

DSP Level (-6 dB to +3 dB)

Rev. Delay (0 to 250 ms)

Rev. Level (0 to 100 %)


Center Width (0 to 7)

Dialogue Lift (0 to 5)

9

10

SET MENU TABLE / MANUAL SETUP GUIMAIN MENU SUB MENU PARAMETER-20.0 dB to 0.0 dB, 1.0 dB step, [0 dB] [MAX]/STD/MIN [Off]/On [PARAM] [RESET] [EDIT] [EXIT]

VALUE [INITIAL VALUE]

RX-V2700/DSP-AX2700

Sound

LFE Level LFE Dynamic Range Parametric EQ EQ

[Speakers]/Headphones 125 Hz/350 Hz/500 Hz, 6 dB, 0.5 dB step, [0 dB] 2.5 kHz/3.5 kHz/8.0 kHz, 6 dB, 0.5 dB step, [0 dB] [Auto]/Off [Full]/-20 dB -20 dB 0 to 240 ms, 1 ms step, [0 ms] [16.5 dB]/15 dB/10 dB/5 dB/0 dB/-5 dB/-10 dB/-15 dB/-20 dB/-25 dB/-30 dB [Off], -80 dB to +16.5, 0.5 dB step [Off]/On Mute/[Off]

Off/[On] [Off]/On NTSC: Through/[480p]/1080i/720p 480p 1080i720p PAL: Through/[480p]/1080i/720p 480p 1080i720p HDMI AspectHDMI [Through]/16:9 Normal/Smart Zoom 169 Short Message Off/[On] On Screen [Always]/10 sec/30 sec 1030 Position X-Y, -5 to +5, 0 step, [0] Wall Paper None/[Yes]/Gray Test Tone [Off]/On Basic Front Speaker Set [Large]/Small Large/[Small]/None Center Surround Large/[Small]/None Large x 2/[Small x 2]/Large x 1/Small x 1/None 2 2 11 Surround Back Presence Yes/[None] [Both]/SWFR/Front Bass Out Bass Cross Over 40 Hz/60 Hz/[80 Hz]/90 Hz/100 Hz/110 Hz/120 Hz/160 Hz/200 Hz [Normal]/Reverse SWFR Phase PR/SB PriorityPRSB Presence/[Surround Back] meters / feet Unit Speaker Distance Front L 0.3 to 24.0 m, 0.1 m step, [3.0 m] / 1.0 to 80.0 ft, 0.5 ft step, [10.0 ft] 0.3 to 24.0 m, 0.1 m step, [3.0 m] / 1.0 to 80.0 ft, 0.5 ft step, [10.0 ft] Front R Center 0.3 to 24.0 m, 0.1 m step, [2.6 m] / 1.0 to 80.0 ft, 0.5 ft step, [8.5 ft] 0.3 to 24.0 m, 0.1 m step, [2.4 m] / 1.0 to 80.0 ft, 0.5 ft step, [8.0 ft] Surround L Surround R 0.3 to 24.0 m, 0.1 m step, [2.4 m] / 1.0 to 80.0 ft, 0.5 ft step, [8.0 ft] 0.3 to 24.0 m, 0.1 m step, [2.4 m] / 1.0 to 80.0 ft, 0.5 ft step, [8.0 ft] Surround Back L Surround Back R 0.3 to 24.0 m, 0.1 m step, [2.4 m] / 1.0 to 80.0 ft, 0.5 ft step, [8.0 ft] 0.3 to 24.0 m, 0.1 m step, [3.0 m] / 1.0 to 80.0 ft, 0.5 ft step, [10.0 ft] Presence L Presence R 0.3 to 24.0 m, 0.1 m step, [3.0 m] / 1.0 to 80.0 ft, 0.5 ft step, [10.0 ft] 0.3 to 24.0 m, 0.1 m step, [3.0 m] / 1.0 to 80.0 ft, 0.5 ft step, [10.0 ft] Subwoofer Front L Speaker Level -10.0 to +10.0 dB, 0.5 dB step, [0 dB] -10.0 to +10.0 dB, 0.5 dB step, [0 dB] Front R Center -10.0 to +10.0 dB, 0.5 dB step, [0 dB] -10.0 to +10.0 dB, 0.5 dB step, [-1.0 dB] Surround L Surround R -10.0 to +10.0 dB, 0.5 dB step, [-1.0 dB] -10.0 to +10.0 dB, 0.5 dB step, [-1.0 dB] Surround Back L Surround Back R -10.0 to +10.0 dB, 0.5 dB step, [-1.0 dB] -10.0 to +10.0 dB, 0.5 dB step, [0 dB] Presence L Presence R -10.0 to +10.0 dB, 0.5 dB step, [0 dB] -10.0 to +10.0 dB, 0.5 dB step, [0 dB] Subwoofer DHCP DHCP Network NET/USB Off/[On] 000.000.000.000 [192.168.182.002] IP IP Address Subnet Mask 000.000.000.000 [255.255.255.000] Default Gateway 000.000.000.000 [192.168.182.001] DNS Server P DNS P [000.000.000.000] [000.000.000.000] DNS Server S DNS S Setup Set: Enter [Off]/Single/All 1 Repeat Play Style Shuffle [Off]/On MAC AddressMAC00:A0:DE:xx:xx:xx Information Status 10BASE-T/100BASE-TX/Full Duplex/Half Duplex/No Link 10BASE-T100BASE-TX System xxxxxxxx -4 to 0 [0] Dimmer Front Panel Disp. Option Scroll [Continue]/Once 1 Off/[On] Standby Charge iPod iPod Zone OSD Off/Zone2/[Zone2&Zone3] [EXT]/INT:SP[1]/INT:SP[2]/INT:Both Zone2 Amplifier Zone2 Set Zone2 Volume Fixed/[Variable] [16.5 dB]/15 dB/10 dB/5 dB/0 dB/-5 dB/-10 dB Zone2 Max Vol. (U, C, R, T, K, Zone2 Initial Vol. A, B, G, E, L [Off], -80 dB to +16.5, 0.5 dB step [EXT]/INT:SP[1]/INT:SP[2]/INT:Both Zone3 Amplifier Zone3 Set models) Zone3 Volume Fixed/[Variable] [16.5 dB]/15 dB/10 dB/5 dB/0 dB/-5 dB/-10 dB Zone3 Max Vol. Zone3 Initial Vol. [Off]/-80 dB to +16.5, 0.5dB step Sur.Initialize CLASSICAL/LIVE/CLUB/ENTERTAINMENT/MOVIE/STEREO/SUR.DECODE/ALL Audio Select [Auto]/Last Decoder Mode [Auto]/Last Memory Guard [On]/Off HDMI Set HDMI Support Audio [RX-V2700]/Other DSP-AX2700

Video

Speaker Headphone Speaker Headphone Test Tone Front L Front R Center Surround L Surround R Sur.Back L Sur.Back R Presence L Presence R Subwoofer Control Tone Control Bass Treble Auto Bypass Muting Type Audio Option Audio Delay Max Volume Initial Volume (J model) Mode Channel Mute Front L Front R Center Surround L Surround R Surround Back L Surround Back R Presence L Presence R Subwoofer Conversion Component I/PIP HDMI Up-ScalingHDMI

RX-V2700/DSP-AX2700

I INTERNAL VIEWRX-V2700/DSP-AX2700

Top view 1 2 3 4 56 7 8 90 1 2 3 4 5 6 7 8 9 0 A B C D E F G H I J K L M N O P Q R S T U Power Transformer POWER (4) P.C.B. POWER (2) P.C.B. (R, L models) TUNER MAIN (2) P.C.B. FL (3) P.C.B. FL (5) P.C.B. FL (4) P.C.B. A-VIDEO P.C.B. FL (2) P.C.B. D-VIDEO P.C.B. FUNCTION (1) P.C.B. FUNCTION (2) P.C.B. DSP P.C.B. MAIN (1) P.C.B. POWER (3) P.C.B. POWER (5) P.C.B. POWER (6) P.C.B. POWER (1) P.C.B. OPERATION (5) P.C.B. OPERATION (1) P.C.B. OPERATION (4) P.C.B. OPERATION (3) P.C.B. OPERATION (6) P.C.B. OPERATION (7) P.C.B. FL (1) P.C.B. OPERATION (2) P.C.B. NET P.C.B. FL (6) P.C.B. MAIN (4) P.C.B. MAIN (3) P.C.B.


A B C D E F G

I

H

Front view

J K L Rear view

M

N

OP Q

R

S

T

U

11

RX-V2700/DSP-AX2700

I DISASSEMBLY PROCEDURES / (Remove parts in the order as numbered.) Disconnect the power cable from the AC outlet. AC

1. Removal of Top Covera. Remove 2 screws (1), 4 screws (2) and 5 screws (3). (Fig. 1) b. Slide the top cover rearward to remove it. (Fig. 1)RX-V2700/ DSP-AX2700

1. a. 122435 Fig. 1 b. Fig. 1

2. Removal of Front PanelRemove 6 screws (4) and then remove the front panel forward. (Fig. 1)

2. 4 6 Fig. 1

3 2 1 Top cover

3

2

4

4 Front panel

Fig. 1

3. Removal of Sub Chassis Unita. Remove 3 screws (5) and then remove the frame top. (Fig.2) b. Remove 4 push rivets (6) and then remove the side plates L/R. (Fig. 2) c. Remove 1 screw (7), 2 screws (8) and 3 screws (9). (Fig. 2) d. Remove CB12, CB805807, CB814, CB970 and CB971. (Fig. 3) e. Remove the sub chassis unit forward. (Fig. 2)

3. a. 53/ Fig. 2 b. 64L/R Fig. 2 718293 c. Fig. 2 d. CB12CB805807CB814CB970CB971 Fig. 3 e. Fig. 2

12

RX-V2700/DSP-AX2700

Frame top / 5 5 7

A-VIDEO P.C.B.

Side plate L L 6

D-VIDEO P.C.B.

6 A 6RX-V2700/ DSP-AX2700

8

B (R, K, A, L models) B Shield plate (U, C, T, B, G, E, J models)

Sub chassis unit 8 Side plate R R

9 6 0

Fig. 2CB209 CB204 CB203

CB953

CB957 CB23 CB136 CB970 CB971 CB805 CB12 CB807 CB806 CB814

Fig. 3

4. Removal of D-VIDEO P.C.B.a. Remove 2 screws (0) and then remove the shield plate (U, C, T, B, G, E models). (Fig. 2) b. Remove 1 screw (A) and 2 (U, C, T, B, G, E models) / 3 (R, K, A, L models) screws (B). (Fig. 2) c. Remove 5 screws (C). (Fig. 5) d. Remove CB136, CB204, CB953 and CB957. (Fig. 3) e. Remove the D-VIDEO P.C.B. which is connected directly to the A-VIDEO P.C.B. with connectors. (Fig. 2)

4. D-VIDEO P.C.B.a. 0 2 Fig. 2 b. A1B2 Fig. 2 c. C5 Fig. 5 d. CB136CB204CB953CB957 Fig. 3 e. D-VIDEO P.C.B.D-VIDEO P.C.B.A-VIDEO P.C.B. (Fig. 2)

5. Removal of A-VIDEO P.C.B.a. Remove 6 screws (D). (Fig. 5) b. Remove CB23, CB203 and CB209. (Fig. 3) c. Remove the A-VIDEO P.C.B.. (Fig. 2)

5. A-VIDEO P.C.B.a. D10 Fig. 5 b. CB23CB203 Fig. 3 c. A-VIDEO P.C.B. Fig. 2 13

RX-V2700/DSP-AX2700

When checking the P.C.B.: Place the sub chassis unit on top of the rubber sheet and cloth. (Fig. 4) Reconnect all cables (connectors) that have been disconnected. Use the extension cable before servicing the following section. FL (1) P.C.B. CB901_FL (2) P.C.B. CB970: MF126500 (26P, 500mm) FL (2) P.C.B. CB971_OPERATION (2) P.C.B. CB803: MF115500 (15P, 500mm) FL (1) P.C.B. W9001_POWER (1) P.C.B. CB12: MF405400 (5P, 400mm) When connecting the flexible flat cable, be careful with polarity. In main unit, the ground of sub chassis unit is connected to the chassis. When this sub chassis unit are removed from chassis, connect the ground to the chassis, using a ground lead or such. (Fig. 4)

P.C.B. Fig. 4 FL 1 P.C.B. CB901_FL 2 P.C.B. CB970 MF126500 26P500mm FL 2 P.C.B. CB971_OPERATION P.C.B. CB803 2 MF115500 15P500mm FL 1 P.C.B. W9001_POWER 1 P.C.B. CB12 MF405400 5P400mm Fig. 4


POWER (1) P.C.B.

FL (2) P.C.B. CB12 Ground lead

MF405400 Sub chassis unit Rubber sheet and cloth Chassis

CB971 W9001 FL (1) P.C.B. CB901 OPERATION (2) P.C.B. CB803 MF115500 CB970 MF126500

Fig. 4

14

RX-V2700/DSP-AX2700 U, C, R, T, K, A, B, G, E, L modelsC D E (R, L models) F

E

F (U, C, R, T, A, B, G, E, L models)

J modelC D F

When checking the P.C.B.: Put the rubber sheet and the cloth over the equipment. Then place the P.C.B.s upside down on the cloth and check it. (Fig. 6) Reconnect all cables (connectors) that have been disconnected. Use the extension cable before servicing the following section. FL (1) P.C.B. CB953_D-VIDEO P.C.B. CB140: MF120400 (10P, 350mm) FUNCTION (1) P.C.B. CB410_A-VIDEO P.C.B. CB203: MF117350 (11P, 70mm) FL (2) P.C.B. CB957_D-VIDEO P.C.B. CB138: MF115500 (15P, 500mm) When connecting the flexible flat cable, be careful with polarity. In this unit, the ground of P.C.B.s shown below is connected to the rear panel. When these P.C.B.s are removed from the rear panel, connect the ground point to the rear panel or chassis, using a ground lead or such. (Fig. 6) D-VIDEO P.C.B. ST101 (Ground) D-VIDEO P.C.B. CB103 (HDMI IN2) A-VIDEO P.C.B. PJ204 (COMPONENT VIDEO)

P.C.B. P.C.B. Fig. 6 FL 1 P.C.B. CB953_D-VIDEO P.C.B. CB140 MF120400 10P350mm FUNCTION P.C.B. CB410_A-VIDEO P.C.B. CB203 1 MF117350 11P70mm FL 2 P.C.B. CB957_D-VIDEO P.C.B. CB138 MF115500 15P500mm P.C.B. P.C.B. Fig. 6 D-VIDEO P.C.B. ST101 Ground D-VIDEO P.C.B. CB103 HDMI IN2 A-VIDEO P.C.B. PJ204 COMPONENT VIDEO Ground point

D-VIDEO P.C.B.

Ground lead

A-VIDEO P.C.B. CB140E

D-VIDEO P.C.B. MF11500 CB138 CB957 MF120400 CB953 MF117350 FL (2) P.C.B. Rear panel A-VIDEO P.C.B. CB203 Ground lead

Fig. 5

Rubber sheet and cloth

CB410

FUNCTION (1) P.C.B.

Fig. 6 15

RX-V2700/DSP-AX2700

6. Removal of Rear Unita. Remove 10 (U, C, T, A, B, G, E models) / 13 (R, L models) screws (E) and 4 (U, C, R, T, A, B, G, E, L models) / 2 (K model) screws (F). (Fig. 5) b. Remove 4 screws (G), 1 screw (H) and 1 screw (I). (Fig. 7) c. Remove CB16-18, CB20, CB303, CB406 and CB407. (Fig. 7) d. Remove the rear unit and MAIN (2) P.C.B.. (Fig. 7)

6. a. E9F4 Fig. 5 b. G 4 H 1 I 1 Fig. 7 c. CB1618CB20CB303CB406407 d. MAIN 2 P.C.B.

FUNCTION (1) P.C.B.

Rear unit DSP P.C.B.

MF126500 FL (2) P.C.B.

CB970

CB971

Rear unit

CB303

CB406

CB407

Ground lead

MF115500

Chassis CB901 CB803 Rubber sheet and cloth

G G CB18 I H MAIN (2) P.C.B.

Fig. 8

7. Removal of Amp UnitG CB20 CB17 CB16

7. a. J2K5L2 Fig. 9 b. CB6CB11CB15CB253 Fig. 9 c. Fig. 9K CB253

a. Remove 2 screws (J), 5 screws (K) and 2 screws (L). (Fig. 9) Fig. 7 b. Remove CB6, CB11, CB15 and CB253. (Fig. 9) c. Remove the amp unit. (Fig. 9)K CB15

CB11

When checking the DSP P.C.B.: Put the rubber sheet and the cloth over the equipment. Then place the P.C.B.s upside down on the cloth and check it. (Fig. 8) Reconnect all cables (connectors) that have been disconnected. Use the extension cable before servicing the following section. FL (1) P.C.B. CB901_FL (2) P.C.B. CB970: MF126500 (26P, 500mm) FL (2) P.C.B. CB971_OPERATION (2) P.C.B. CB803: MF115500 (15P, 500mm) When connecting the flexible flat cable, be careful with polarity. In main unit, the ground of rear unit is connected to the chassis. When this rear unit are removed from chassis, connect the ground to the chassis, using a ground lead or such. (Fig. 8)

DSP P.C.B. P.C.B. Fig. 8 FL 1 P.C.B. CB901_FL 2 P.C.B. CB970 MF126500 26P500mm FL 2 P.C.B. CB971_OPERATION P.C.B. CB803 2 MF115500 15P500mm Fig. 8

CB6 Amp unit

J

L

Fig. 9

16

RX-V2700/DSP-AX2700

When checking the Amp Unit: Place the sub chassis unit on top of the rubber sheet and cloth. (Fig. 10) Put the amp unit together with the heat sink upright and check them. (Fig. 10) Reconnect all cables (connectors) that have been disconnected. Use the extension cable before servicing the following section. FL (1) P.C.B. CB901_FL (2) P.C.B. CB970: MF126500 (26P, 500mm) FL (2) P.C.B. CB971_OPERATION (2) P.C.B. CB803: MF115500 (15P, 500mm) FL (1) P.C.B. W9001 _ POWER (1) P.C.B. CB12: MF405400 (5P, 400mm) When connecting the flexible flat cable, be careful with polarity. In main unit, the ground of sub chassis unit and amp unit is connected to the chassis. When this sub chassis unit and amp unit are removed from chassis, connect the ground to the chassis, using a ground lead or such. (Fig. 10)

Fig. 10 Fig. 10 FL 1 P.C.B. CB901_FL 2 P.C.B. CB970 MF126500 26P500mm FL 2 P.C.B. CB971_OPERATION 2 P.C.B. CB803 MF115500 15P500mm FL 1 P.C.B. W9001_POWER 1 P.C.B. CB12 MF405400 5P400mm Fig. 10


MF405400 Ground lead POWER (1) P.C.B. MAIN (1) P.C.B. Sub chassis unit Rubber sheet and cloth

CB12

Amp unit Cloth

Ground lead

Chassis

FL (2) P.C.B. CB971 W9001 FL (1) P.C.B. CB901 OPERATION (2) P.C.B. CB803 MF115500 CB970 MF126500

Fig. 10

17

RX-V2700/DSP-AX2700

I UPDATING FIRMWARE / When replacing the following parts, be sure to write the latest firmware. DSP P.C.B. FUNCTION P.C.B. D-VIDEO P.C.B. NET P.C.B. IC540 of DSP P.C.B. : X8012A00 IC402 of FUNCTION P.C.B.: X8338A00 IC147 of D-VIDEO P.C.B. : X8072A00 * The IC613 of NET P.C.B. is not supplied as a replacement part. DSP P.C.B. FUNCTION P.C.B. D-VIDEO P.C.B. NET P.C.B. DSP P.C.B.IC540 X8012A00 FUNCTION P.C.B.IC402 X8338A00 D-VIDEO P.C.B.IC147 X8072A00 NET P.C.B.IC613


G Required tools USB flash memory Firmware (RXV2700-xxxx.bin)

USB RXV2700-xxxx.bin

G Operation Procedures1. Download the latest firmware from the specified download source to PC. 2. Copy the latest firmware into the root folder of the USB flash memory. Note) When the firmware is copied into the sub-folder, it is not possible to write data in it.

1. PC 2. USB 3. AC 4. STRAIGHT MASTER ON/OFF Fig. 1

3. Connect the power cable of main unit to the AC outlet. 4. Press the MASTER ON/OFF key of the main unit while simultaneously pressing the STRAIGHT key of the main unit. Then the ADVANCED SETUP mode is activated. (Fig. 1)"TONE CONTROL" key

USB terminal

"PROGRAM" knob "MASTER ON / OFF" key "STRAIGHT" key "NIGHT" key

SPEAKER IMP. 8MINFig. 1 5. Keep pressing the NIGHT key of the main unit for about 3 seconds. (Fig. 1) Writing of the firmware is started. (Fig. 2) 5. I G H T N 3 Fig. 1 Fig. 2

18

RX-V2700/DSP-AX2700

Firm Update SelectCDDA/USBFig. 2 6. Turn the PROGRAM knob to select USB. 7. Press the NIGHT key of the main unit. (Fig. 1) Writing of the firmware is set in the wait mode. 8. Insert the USB flash memory to the USB terminal of the main unit. (Fig. 1) Writing of the firmware is started. * It takes about 10 seconds before writing is started. 6. PROGRAM USB 7. NIGHT Fig. 1 8. USBUSB Fig. 1 10 Writing is completed. /


Writing in wait mode. /

Writing being executed. /

USB Upgrader 2700

Updating... Step x/x : yy%

FirmwareUpdate is complete!

9. When writing of the firmware is completed, the power of the main unit turns OFF/ON automatically. * If Firmware Update is complete! is not displayed, or the error message as shown below is displayed before writing is completed, perform the operation procedures from step 1 to 10 all over again. Error display / Contents /

9. OFF/ON Firmware Update is complete! 110

No USB Device When the USB flash memory is disconnected while the firmware is being written. (Connecting the USB flash memory to the main unit again will start writing process again.) / USB USB firmware Error The firmware is not written in the USB flash memory or does not exist in the root folder. / USB Erasing the flash ROM stops before the process is completed. / Erase Error ROM Writing the flash ROM stops before the process is completed. / Write Error ROM Checksum Error The data check after writing cannot be verified. /

*

If it is not possible to turn on the power after writing the firmware (failure in writing), perform the following procedure. a. Disconnect the power cable from the AC outlet. b. While pressing the TONE CONTROL key of the main unit, reconnect the power cable to the AC outlet. c. Perform the operation procedures from step 8 again.

a. AC b. TONE CONTROL AC c. 8

19

RX-V2700/DSP-AX2700

I SELF DIAGNOSIS FUNCTION (DIAG) There are 29 DIAG menu items, each of which has submenu items. Listed in the table below are menu items and sub-menu items. No. DIAG MENU 1RX-V2700/ DSP-AX2700

2 9

SUB MENU 1. MARGIN 2. FULL BIT 1. ANALOG BYPASS 2. DSP BYPASS 1. MARGIN 2. FULL BIT 1. SPDIF 2. Multi 3. DSD 4. DSD Direct 1. FRONT:SMALL 0dB 2. LFE/B:FRNT 3. Pres Mix:5ch 4. FATT1 GAIN 5. FATT2 GAIN 6. Surr B:MUTE 7. Surr L/R:MUTE 8. Zone Amp on, Tone:MAX (U, C, R, T, K, A, B, G, E, L models) 9. Zone Amp on, Tone:MIN (U, C, R, T, K, A, B, G, E, L models) 10. Effect Ch SML 1. 6ch INPUT_6-ohm 2. 8ch INPUT_6-ohm 3. 6ch INPUT_8-ohm 4. 8ch INPUT_8-ohm 5. TMP TEST/AMP. POWER CONTROL 1. MIC CHECK 1. VSYNC CHECK/VIDEO CONVERSION ON 2. VFD DISP OFF/VIDEO MUTE 3. VFD DISP ALL/OSD CHARACTERS (0-127) 4. VFD DIMMER/OSD CHARACTERS (128-255) 5. CHECK PATTERN/VIDEO CONVERSION OFF 1. TEST ALL 2. TEST FRNT L 3. TEST CENTER 4. TEST FRNT R 5. TEST SURR R 6. TEST SB R 7. TEST SB L 8. TEST SURR L 9. TEST PRES L 10. TEST PRES R 11. TEST LFE 1. TX DATA 2. HARD FLOW 1. DC 2. PS1/PS2 3. TM1/TM2 4. OUTLVL 5. LMTCNT 6. AMPRELAY

INPUT SELECT DVD DVD DVD DVD DVD (Zone 2/3) DVD (Zone 2/3) DTV (Zone 2/3) CBL/SAT (Zone 2/3) VCR1 (Zone 2/3) VCR2/DVR (Zone 2/3) V-AUX (Zone 2/3) MD/TAPE (Zone 2/3) CDR (Zone 2/3) CD (Zone 2/3) PHONO (Zone 2/3) TUNER (Zone 2/3)

DA70Y-YSS930 BYPASS RAM THROUGH HDMI AUDIO

2 3 4

5

SPEAKERS SET

6

MULTI CH INPUT

7 8

MIC CHECK FL/OSD CHECK

9

MANUAL TEST

10 RS-232C 11 AD DATA CHECK

20

RX-V2700/DSP-AX2700

No DIAG MENU

SUB MENU 7. MODEL 8. DESTINATION 9. PANEL KEY (K0/K1) 1. 1k -1dB/44.1k 2. 1k -61dB/44.1k 3. Mute/44.1k 4. XM Tone/44.1k 5. ISO Tone/44.1k 6. 1k -1dB/32k 7. 1k -61dB/32k 8. Mute/32k 9. XM Tone/32k 10. ISO Tone/32k 11. XM/DT Bus Power:OFF 1. INSIDE STATUS 1 (5Byte) 2. INSIDE STATUS 2 (2Byte) 3. CHANNEL STATUS 1 (5Byte) 4. CHANNEL STATUS 2 (5Byte) 5. CHANNEL STATUS 3 (4Byte) 6. BS 1 (2Word) 7. BS 2 (2Word) 8. BS 3 (2Word) 9. BS 4 (2Word) 10. BS 5 (2Word) 11. BS 6 (2Word) 12. BS 7 (2Word) 13. BS 8 (2Word) 14. BS 9 (2Word) 15. BS a (2Word) 16. TI 1 (5Byte) 17. TI 2 (1Byte) 18. Mute Trigger (5Byte) 1. DOCK 1. IP Address Check 2. MAC Address CHECK 1. USB 1track 2. USB 2track 1. LAST 2. HIST1 3. HIST2 4. HIST3 1. TI BUS 2. YSS-930 BUS 1. ALL Check 2. Microprocessor/Flash Check 3. I2C Read Check 4. YGV Bus Check 1. HDMI Model Name 2. HDMI Product ID 3. HDMI Vendor Name 1. HDMI NONE 2. HDMI IN 1 3. HDMI IN 2 4. HDMI IN 3 1. HDMI Decoder 2. HDMI YGV

INPUT SELECT DVD DVD DVD DVD DVD DVD DVD DVD DVD DVD DVD DVD DVD DVD DVD DVD DVD DVD V-AUX NET/USB NET/USB NET/USB NET/USB DVD DVD DVD DVD

No DIAG MENU

SUB MENU 3. HDMI I/P 4. HDMI 720p 5. HDMI 1080p (Not applied to these models. / ) 6. HDMI SMART ZOOM 1. DIGITAL THR COMP 2. DIGITAL THR CVBS 3. DIGITAL THR Y/C 4. DIGITAL BYPASS 5. ANALOG BYPASS 6. TEST PATTERN 1 7. TEST PATTERN 2 8. VIDEO INFO 1. TI FLASH READ 2. TI FLASH WRITE 3. TI SDRAM READ 4. TI SDRAM WRITE 5. YGV READ 6. YGV WRITE 1. 232C MAIN 2. 232C VIDEO 3. 232C TI 4. USB NET 1. MODEL 2. DEST. 1. SW MODE 2. VIDEO FORMAT 3. AAC 4. CSII 5. RDS 6. XM 7. Neural Audio 8. TMP TEST 1. PRESET INH 2. PRESET RSRV 1. MAIN VERSION 2. MAIN SUM 3. VIDEO VERSION 4. VIDEO SUM 1 5. VIDEO SUM 2 6. TI FLASH VERSION 7. TI FLASH SUM 8. XM VERSION (U, C models) 9. Net VERSION 10. Net SUM

INPUT SELECT

12 XM TEST TONE (U, C models)

23 VIDEO

13 IF STATUS

24 ACCESS CHECK (Not applied to these models. / )

25 Firm UPDATE

26 SET INFO 27 SOFT SW

14 iPod 15 Net 16 USB 17 PROTECTION HIST.

28 FACTORY PRESET 29 ROM VER/SUM

18 DSP PCB CHECK 19 DVIDEO PCB CHECK

20 HDMI INFO

21 HDMI SELECT

22 HDMI UP CONV.

21

RX-V2700/DSP-AX2700

Starting DIAGPress the MASTER ON/OFF key while simultaneously pressing those two keys of the main unit as indicated in the figure below.

MASTER ON/ OFF

Display provided when DIAG startedThe FL display of the main unit displays the protection function history data and the version (1 alphabet) then the DIAG menu (sub-menu MARGIN of DIAG menu No.1 DA70Y-YSS930) a few seconds later.

FL 1 No.1 DA70Y-YSS930MARGIN

Keys of main unit /

When there is no history of protection function:Opening message /

:DIAG menu display /

Turn on the power while pressing these keys.

When there is no history of protection function

Version (1 alphabet) 1 After a few seconds

Starting DIAG in the protection cancel modeIf the protection function works and causes hindrance to trouble shoot, cancel the protection function as described below, and it will be possible to enter the DIAG mode. (The protection functions other than the excess current detect function will be disabled.) Press the MASTER ON/OFF key while simultaneously pressing those two keys indicated in the figure above. At this time, keep pressing those two keys for 3 seconds or longer. In this mode, the SLEEP segment of the FL display of the main unit flashes to indicate that the mode is DIAG mode with the protection functions disabled. CAUTION! Using this product with the protection function disabled may cause damage to itself. Use special care when using this mode.

MASTER ON/OFF 3 FL SLEEP

DIAGNOSTIC NO PROTECT F

1.DA70Y-YSS930 MARGIN

When there is a history of protection function:

:

When there is a history of protection function due to excess current

Version (1 alphabet) 1

I PROTECT

F

Cause: An excessive current flowed through the power amplifier. Suppleementary information: As current of the power transistor is detected, the abnormal channel can be identified by checking the current detect transistor. Turning on the power without correcting the abnormality will cause the protection function to work immediately and the power supply will instantly be shut off. Note) Applying the power to the main unit without correcting the abnormality can be dangerous and cause additional circuit damage. The output transistors in each amplifier channel should be checked for damage before applying power of the main unit. Amplifier current should be monitored by measuring across the emitter resistors for each channel.

Canceling DIAG1 Before canceling DIAG, execute setting for PRESET of DIAG menu No.11 (Memory initialization inhibited or Memory initialized). * In order to keep the user memory stored, be sure to select PRESET INHIBIT (Memory initialization inhibited). 2 Turn off the power by pressing the MASTER ON/OFF key of the main unit or the STANDBY key of the remote control.

No.11 FACTORY PRESET/ PRESET INHIBIT MASTER ON/OFF STANDBY

22

RX-V2700/DSP-AX2700When there is a history of protection function due to abnormal voltage in the power supply section


PSx PRT:000 FA/D conversion value of voltage A/D

Cause: The voltage in the power supply section is abnormal. Supplementary information: The abnormal voltage is displayed in based on 5V as 255. Turning on the power without correcting the abnormality will cause the protection function to work 1 second later and the power supply will be shut off.

5V255 1


When there is a history of protection function due to abnormal DC output DC


DC PRT:000 FA/D conversion value of voltage A/D

Cause: DC output of the power amplifier is abnormal. Supplementary information: The abnormal voltage is displayed in based on 5V as 255. Turning on the power without correcting the abnormality will cause the protection function to work 3 seconds later and the power supply will be shut off.

DC 5V255 3

When there is a history of protection function due to excessive heat sink temperature


TMPx PRT:000 FA/D conversion value of voltage A/D

Cause: The temperature of the heat sink is excessive. Supplementary information: The abnormal voltage is displayed in based on 5V as 255. Turning on the power without correcting the abnormality will cause the protection function to work 1 second later and the power supply will be shut off. * Additional causes of protection can be due to loose connections, associated components, Microprocessor, etc. For the protection voltage value, refer to DIAG menu No.11 described later.

5V255 1

*

Microprocessor No.11

23

RX-V2700/DSP-AX2700

History of protection functionWhen the protection function has worked, its history is stored in memory with a backup. Even if no abnormality is noted while servicing the unit, an abnormality which has occurred previously can be defined as long as the backup data has been stored. The history of the protection function is cleared when DIAG is cancelled by selecting PRESET RESERVED (Memory initialized) of DIAG menu No. 28 or when the backup data is erased.RX-V2700/ DSP-AX2700

No.28 PRESET RESERVED

Display during menu operation

FL

During the DIAG mode, the monitor screen shows the wall paper and the selected function among following functions as a short message. Input selection, multi channel input Muting Master volume The FL display of the main unit shows the selected function. The displayed contents are described in the later section on details of DIAG menu.

Operation procedure of DIAG menu and Sub-menuThere are 29 menu items, each of having sub-menu items.

No.129

DIAG menu selectionSelect the menu using PROGRAM knob.

PROGRAM

Sub-menu selectionSelect the sub-menu using (Forward) and verse) keys of PRESET/TUNING. (Re-

PRESET/TUNING

Sub-menu selection U, C models

DIAG menu selection

Reverse

Forward Reverse Forward

R, T, K, A, B, G, E, L, J models

Reverse

Forward

24

RX-V2700/DSP-AX2700

Functions in DIAG mode

/ AUDIO SELECT No.13 IF STATUS

In addition to the DIAG menu items, functions listed below are available. Input selection, Multi channel input Center/Rear/Rear center/Sub-woofer level adjustment Muting Power on/off Master volume * * Functions related to the tuner and the set menu are not available. It is possible to confirm menu No.13 IF STATUS while keeping the signal process (operation status) of each DIAG menu by using the AUDIO SELECT key of the main unit.


Initial settings used to start DIAG

-20dB DVD INPUT 0dB LARGE / BASS OUT=BOTH DA70Y-YSS930 1. MARGIN

The following initial settings are used when starting DIAG. When DIAG is canceled, these settings are restored to those before starting DIAG. Master volume: -20dB Input: DVD (MULTI CHANNEL INPUT OFF) Effect level: 0dB Audio mute: OFF Speaker setting: LARGE / BASS OUT = BOTH DIAG menu: DA70Y-YSS930 (1. MARGIN)

Input change when DIAG menu is selectedThere are points where the input changes automatically when DIAG menu is selected. 8. FL/OSD TEST: DVD 9. MANUAL TEST: DVD 13. IF STATUS: DVD 14. iPod: V-AUX/DOCK 15. Net: NET/USB 16. USB: NET/USB 17. PROTECTION HISTORY: DVD

8. FL/OSD TESTDVD 9. MANUAL TESTDVD 13. IF STATUSDVD 14. iPodV-AUX/DOCK 15. NetNET/USB 16. USBNET/USB 17. PROTECTION HISTORYDVD

25

RX-V2700/DSP-AX2700

Details of DIAG menu

0dBFS

With full-bit output specified in some modes, it is possible to execute 0dBFS output without head margin in each channel.

1. DA70Y-YSS930This function is for YSS930 only. Main DSP of YSS930 is selected for FRONT output. Using the sub-menu, it is possible to select 0dB output level or full-bit output.RX-V2700/ DSP-AX2700

1. DA70Y-YSS930YSS930FRONTYSS930 Main DSP 0dB MARGIN

MARGIN The signal is output including the head margin.

1.DA70Y-YSS930 MARGININPUT: DVD ANALOG SPEAKER OUT: 1kHz, SUBWOOFER OUTPUT: 50Hz Input level Volume FRONT +12.5 dBm CENTER +13.5 dBm SPEAKER OUT SUBWOOFER OUTPUT SURROUND SURROUND BACK PRESENCE +13.5 dBm +13.5 dBm - -5.5 dBm

Both ch, -20 dBm +6.5 dB

FULL BIT The signal is output in digital full bit without including the head margin. The SWFR signal is output but not in digital full bit.

FULL BIT SWFR

1.DA70Y-YSS930 FULL BITINPUT: DVD ANALOG SPEAKER OUT: 1kHz, SUBWOOFER OUTPUT: 50Hz Input level Volume SPEAKER OUT FRONT +12.5 dBm CENTER +13.5 dBm SURROUND SURROUND BACK PRESENCE +13.5 dBm +13.5 dBm - SUBWOOFER OUTPUT -5.5 dBm

Both ch, -20 dBm +6.5 dB DA70Y-YSS930 (ANALOG)

4Mbit DRAMDIR L/R

Analog

A/D PCM1804

AD L/R

L/R

L/R

L/R

L/R

SL/SR C/LFE SBL/ SBR

SL/SR SBL/ SBR C SWL/ SWR

SL/SR SBL/SBR or PL/PR

C SWL/SWR

DigitalDIR DECODE DSP POST PROCESSING DSP

PL/PR ReL/ ReR

POST PROCESSING DSP

PL/PR

LC89057

TI DA70Y

YSS930 D0

YSS930 D1

(Shaded items not used in this mode) 26

RX-V2700/DSP-AX2700

2. BYPASSANALOG BYPASS

2. BYPASSANALOG BYPASS

2.BYPASS ANALOG BYPASSINPUT: DVD ANALOG SPEAKER OUT: 1kHz, SUBWOOFER OUTPUT: 50Hz Input level Volume FRONT +12.5 dBm CENTER - SPEAKER OUT SUBWOOFER OUTPUT SURROUND SURROUND BACK PRESENCE - - - -RX-V2700/ DSP-AX2700


DSP BYPASS

DSP BYPASS

2.BYPASS DSP BYPASSINPUT: DVD ANALOG SPEAKER OUT: 1kHz, SUBWOOFER OUTPUT: 50Hz Input level Volume FRONT +12.5 dBm CENTER - SPEAKER OUT SUBWOOFER OUTPUT SURROUND SURROUND BACK PRESENCE -4Mbit DRAMDIR L/R


-

-

-

ANALOG BYPASS, DSP BYPASS (ANALOG)

Analog

A/D PCM1804

AD L/R

L/R

L/R

L/R

L/R




C SWL/SWR


PL/PR ReL/ ReR

POST PROCESSING DSP

PL/PR

LC89057

TI DA70Y

YSS930 D0

YSS930 D1

(Shaded items not used in this mode) DSP BYPASS (DIGITAL)4Mbit DRAMDIR L/R

Analog

A/D PCM1804

AD L/R

L/R

L/R

L/R

L/R




C SWL/SWR


PL/PR ReL/ ReR

POST PROCESSING DSP

PL/PR

LC89057

TI DA70Y

YSS930 D0

YSS930 D1

(Shaded items not used in this mode) 27

RX-V2700/DSP-AX2700

3. RAM THROUGHUsing the sub-menu, it is possible to select the full-bit output at 0dB output level. MARGIN

3. RAM THROUGH0dB MARGIN

3.RAM THROUGH MARGINRX-V2700/ DSP-AX2700

INPUT: DVD ANALOG SPEAKER OUT: 1kHz, SUBWOOFER OUTPUT: 50Hz Input level Volume FRONT +12.5 dBm CENTER +13.5 dBm SPEAKER OUT SUBWOOFER OUTPUT SURROUND SURROUND BACK PRESENCE +13.5 dBm +13.5 dBm - -5.5 dBm

Each ch, -20 dBm +6.5 dB

FULL BIT

FULL BIT

3.RAM THROUGH FULL BITINPUT: DVD ANALOG SPEAKER OUT: 1kHz, SUBWOOFER OUTPUT: 50Hz Input level Volume SPEAKER OUT FRONT +12.5 dBm CENTER +13.5 dBm SURROUND SURROUND BACK PRESENCE +13.5 dBm +13.5 dBm -4Mbit DRAMDIR L/R

SUBWOOFER OUTPUT -5.5 dBm

Both ch, -20 dBm +6.5 dB RAM THROUGH (ANALOG)

Analog

A/D PCM1804

AD L/R

L/R

L/R

L/R

L/R




C SWL/SWR


PL/PR ReL/ ReR

POST PROCESSING DSP

PL/PR

LC89057

TI DA70Y

YSS930 D0

YSS930 D1

(Shaded items not used in this mode)

28

RX-V2700/DSP-AX2700

4. HDMI AUDIOThe audio signals input to HDMI IN are selected by the sub-menu and output. * When selecting DSD or DSD Direct, be sure to connect an HDMI unit with DSD output function. SPDIF SPDIF is output.

4. HDMI AUDIOHDMI IN DSDDSD DirectDSD HDMI SPDIF SPDIF

4.HDMI AUDIO SPDIFMulti Multi (DVD-AUDIO) is output. Multi Multi DVD-AUDIO


4.HDMI AUDIO MultiDSD DSD (Direct Stream Digital) is output. DSD DSD Direct Stream Digital

4.HDMI AUDIO DSDDSD Direct DSD (Direct Stream Digital) is output by the direct mode. DSD Direct DSD Direct Stream Digital

4.HDMI AUDIO DSD Direct

5. SPEAKERS SETThe input signal is automatically identified in the order of dts DOLBY DIGITAL AAC PCM Analog. There are 11 sub-menu items as follows. The signals output from the DSP block are the same as sub-menu MARGIN of DIAG menu No.1 DA70Y-YSS930.FRONT: SMALL 0dB

5. SPEAKERS SETdtsDOLBY DIGITALAACPCM 11 DSPNo.1 DA70Y-YSS930MARGIN Press MIX: 5ch

LFE/BASS: FRONT

5.SPEAKERS SET FRONT:SML 0dB

5.SPEAKERS SET LFE/B:FRONT

5.SPEAKERS SET Pres Mix:5ch

FATT1 GAIN

FATT2 GAIN

Surround BACK: MUTE

5.SPEAKERS SET FATT1 GAIN

5.SPEAKERS SET FATT2 GAIN

5.SPEAKERS SET Surr B:MUTE

Surround L/R: MUTE

ZoneOn Zone Amp Tone: MAX

ZoneOn Zone Amp Tone: MIN

5.SPEAKERS SET Surr L/R:MUTE

5.SPEAKERS SET Zone Amp T:MAX

5.SPEAKERS SET Zone Amp T:MIN

EFFECT: SML 0dB

5.SPEAKERS SET Effect ch SML29

RX-V2700/DSP-AX2700 The analog switch settings for each sub-menu are as shown in the table below. SUB MENU 1. FRONT: SMALL 0dB 2. LFE/B: FRNT 3. Pres Mix: 5ch 4. FATT1 GAIN 5. FATT2 GAINRX-V2700/ DSP-AX2700

SL/SR LARGE LARGE LARGE LARGE LARGE LARGE LARGE NONE NONE SMALL SBL/SBR LARGE LARGE LARGE LARGE LARGE LARGE LARGE NONE NONE SMALL LFE/BASS SWFR FRONT SWFR SWFR SWFR SWFR SWFR SWFR SWFR SWFR

FL/FR SMALL LARGE LARGE LARGE LARGE LARGE LARGE LARGE LARGE LARGE

CENTER LARGE LARGE LARGE LARGE LARGE LARGE LARGE LARGE LARGE SMALL

6. Surr B: MUTE 7. Surr L/R: MUTE 8. Zone Amp on, Tone: M 9. Zone Amp on, Tone: M 10. EFFECT: SML 0dB

This mode is used for a speaker with high bass reproduction performance (a large unit). Full bandwidth signals are output. SMALL: This mode is used for a speaker with low bass reproduction performance (a small unit). The signals of 90Hz or less are mixed into the channel specified by LFE/BASS. NONE: This mode is used for no center speaker. The center content is reduced by 3dB and distributed to FRONT L/R. SWFR: LFE of 5.1ch signal or LFE/BASS lower than 90Hz is output through SUBWOOFER OUT. FRONT: LFE of 5.1ch signal or LFE/BASS lower than 90Hz is distributed to FRONT L/R.

LARGE:

LARGE SMALL 90Hz LFE/BASS NONE -3dBFRONT L/ R SWFR 5 . 1 c h L F E 9 0 H zL F E / BASSSUBWOOFER OUT FRONT 5 . 1 c h L F E 9 0 H zL F E / BASSFRONT L/R

INPUT: DVD ANALOG SPEAKER OUT: 1kHz, SUBWOOFER OUTPUT: 50Hz Input level: Both ch, -20 dBm Volume: +6.5 dB SUB MENU 1. FRONT: SMALL 0dB 2. LFE/B: FRNT 3. Pres Mix: 5ch 4. FATT1 GAIN 5. FATT2 GAIN 6. Surr B: MUTE 7. Surr L/R: MUTE 8. Zone Amp on, Tone: M 9. Zone Amp on, Tone: M 10. EFFECT: SML 0dB FRONT +12.5 dBm +14.0 dBm +12.5 dBm +16.5 dBm +18.5 dBm +12.5 dBm +12.5 dBm +18.5 dBm +18.5 dBm +12.5 dBm CENTER - +13.5 dBm +13.5 dBm +13.5 dBm +13.5 dBm +13.5 dBm +13.5 dBm +13.5 dBm +13.5 dBm +13.5 dBm SPEAKER OUT SUBWOOFER OUTPUT SURROUND SURROUND BACK PRESENCE +13.5 dBm +13.5 dBm +13.5 dBm +13.5 dBm +13.5 dBm +13.5 dBm - - - +13.5 dBm - +13.5 dBm +13.5 dBm +13.5 dBm +13.5 dBm - +13.5 dBm - - +13.5 dBm - - - - - - - - - - -10.5 dBm +10.5 dBm - +20.5 dBm +20.5 dBm - - +20.5 dBm +20.5 dBm -3.5 dBm

30

RX-V2700/DSP-AX2700

6. MULTI CH INPUTIt is possible to select the 6ch/8ch input and 6-ohm/8ohm by using the sub-menu. If the TMP TEST (temperature test mode)/AMP. POWER CONTROL menu is selected, it is not possible to use key operation (for selecting the sub-menu). However, it is possible to advance to the next DIAG menu by turning the PROGRAM knob. 6CH INPUT_6-ohm

6. MULTI CH INPUT6ch/8ch6/8 TMP TEST /AMP. POWER CONTROL PROGRAM 6CH INPUT_6RX-V2700/ DSP-AX2700

6.Multi INPUT 6ch INPUT_6INPUT: MULTI CH INPUT SPEAKER OUT: 1kHz, SUBWOOFER OUTPUT: 50Hz Input level Volume SPEAKER OUT FRONT +12.5 dBm CENTER +13.5 dBm SURROUND SURROUND BACK PRESENCE +13.5 dBm - - SUBWOOFER OUTPUT -16.0 dBm


8CH INPUT_6-ohm

8CH INPUT_6

6.Multi INPUT 8ch INPUT_6INPUT: MULTI CH INPUT SPEAKER OUT: 1kHz, SUBWOOFER OUTPUT: 50Hz Input level Volume SPEAKER OUT FRONT +12.5 dBm CENTER +13.5 dBm SURROUND SURROUND BACK PRESENCE +13.5 dBm +13.5 dBm - SUBWOOFER OUTPUT -16.0 dBm


6CH INPUT_8-ohm

6CH INPUT_8

6.Multi INPUT 6ch INPUT_8INPUT: MULTI CH INPUT SPEAKER OUT: 1kHz, SUBWOOFER OUTPUT: 50Hz Input level Volume SPEAKER OUT FRONT +12.5 dBm CENTER +13.5 dBm SURROUND SURROUND BACK PRESENCE +13.5 dBm - - SUBWOOFER OUTPUT -16.0 dBm


8CH INPUT_8-ohm

8CH INPUT_8

6.Multi INPUT 8ch INPUT_8INPUT: MULTI CH INPUT SPEAKER OUT: 1kHz, SUBWOOFER OUTPUT: 50Hz Input level Volume SPEAKER OUT FRONT +12.5 dBm CENTER +13.5 dBm SURROUND SURROUND BACK PRESENCE +13.5 dBm +13.5 dBm - SUBWOOFER OUTPUT -16.0 dBm 31


RX-V2700/DSP-AX2700 TMP TEST/AMP. POWER CONTROL From the power relay of the amplifier section. Use the STRAIGHT key to change operation. TMP TEST /AMP. POWER CONTROL STRAIGHT

6.Multi INPUT 255000047047:HDisplay H (HIGH) M (MID) L (LOW) RY250 (MAIN P.C.B.) RY251 (MAIN P.C.B.) ON OFF OFF OFF ON OFF


7. MIC CHECKThe signals input through the microphone are output via A/D - D/A.

7. MIC CHECKA/DD/A

7.MIC CHECK --- dbThe output level is not indicated.

32

RX-V2700/DSP-AX2700

8. FL/OSD CHECKUse this program to check the FL display section and image control section. When checking the image control section, prepare a monitor, HDMI cable, component video cable, S video cable and video pin cable and connect them. Using the sub-menu operation, the display status of the FL display section and image control section varies as shown below. For audio signal processing, use EFFECT OFF (L/R output by using ANALOG MAIN BYPASS). Checking FL display section

8. FL/OSD CHECKFL HDMI D S FL EFFECT OFF ANALOG MAIN BYPASSL/R RX-V2700/ DSP-AX2700

FL

8.FL/OSD CHECK VSYNC:NONE VSYNC check INPUT: DVD NONE (No signal) / 50Hz/60Hz All segments OFF

All segments ON (dimmer 100%) 100%

All segments ON (dimmer 50%) 50%

Lighting in lattice

Lighting of segments in lattice

Short Normal

Segment conditions of the FL driver and the FL tube are checked by turning ON and OFF all segments. Next, the operation of the FL driver is checked by using the dimmer control. Then a short between segments next to each other is checked by turning ON and OFF all segments alternately (in lattice). (In the above example, the segments in the second row from the top are shorted.)

FL FL FL /

33

RX-V2700/DSP-AX2700 Check of the Video control circuit. (Monitor out) / The image signal is output as follows. Initial display: INPUT [DVD]/ Video conversion ON INPUT DVD / ONVideo conversion ON Input HDMI

Output

COMPONENT VIDEORX-V2700/ DSP-AX2700

S VIDEO VIDEOThrough Video conversion Component interlace/progressive up-conversion HDMI interlace/progressive up-conversion

Video mute/Video conversion OFF /OFF

Video conversion OFF Input HDMI Output

COMPONENT VIDEO

S VIDEO VIDEOThrough

INPUT [DVD]/Video conversion ON / ZONE2/3 out: 0-127 characters ON (U, C, R, T, K, A, B, G, E, L models) INPUT DVD /ON

0-127 characters

INPUT [DVD]/Video conversion ON / ZONE2/3 out: 128-255 characters ON (U, C, R, T, K, A, B, G, E, L models) INPUT DVD /ON

128-255 characters

INPUT [DVD]/Video conversion OFF INPUT DVD /OFF 34

RX-V2700/DSP-AX2700

9. MANUAL TESTThe noise generator with a built-in DSP outputs the test noise through the channels specified by the submenu. The noise frequency for LFE is 35 to 80 Hz. Other than that, the noise frequency is 500 to 2 kHz.TEST ALL

9. MANUAL TESTDSP LFE3580Hz 5002kHz

TEST FRONT L

TEST CENTER

9.MANUAL TEST TEST ALLNoise is output from all channels. TEST FRONT R

9.MANUAL TEST TEST FRNT LNoise is output from the FRONT L channel. FRONT L TEST SURROUND R

9.MANUAL TEST TEST CENTERRX-V2700/ DSP-AX2700

Noise is output from the CENTER channel. CENTER TEST SURROUND BACK R

9.MANUAL TEST TEST FRNT RNoise is output from the FRONT R channel. FRONT R TEST SURROUND BACK L

9.MANUAL TEST TEST SURR RNoise is output from the SURROUND R channel. SURROUND R TEST SURROUND L

9.MANUAL TEST TEST SB RNoise is output from the SURROUND BACK R channel. SURROUND BACK R TEST PRESENCE L

9.MANUAL TEST TEST SB LNoise is output from the SURROUND BACK L channel. SURROUND BACK L TEST PRESENCE R

9.MANUAL TEST TEST SURR LNoise is output from the SURROUND L channel. SURROUND L TEST LFE

9.MANUAL TEST TEST PRES LNoise is output from the PRESENCE L channel. PRESENCE L

9.MANUAL TEST TEST PRES RNoise is output from the PRESENCE R channel. PRESENCE R

9.MANUAL TEST TEST LFENoise is output from the SUB WOOFER channel. SUB WOOFER

10.RS-232CThis menu is used to check transmission of the data and the flow port of the hardware. With the power turned off, short between pins No.2 (RxD) and No.3 (TxD), and between pins No.7 (RTS) and No.8 (CTS) of the RS-232C terminal. (Be sure to turn off the power when shorting the pins.) Start DIAG and select the menu. There are two sub-menu items.RxD TxD1

10.RS-232C RS-232C2 RxD 3 TxD 7 RTS 8 CTS 2

6 2 7 3 8 4 9

5

RTS CTS

TX DATA The sub-menu is used to check transmission of the test data. OK appears when the data is transmitted properly and NG when it is not. In this mode, NULL command transmission is continued after the test command is transmitted.

TX DATA OK NG 200ms NULL

10.RS-232C TX DATA:

NG35

RX-V2700/DSP-AX2700 HARD FLOW This sub-menu is used to check operation of the flow port of the hardware. OK appears when the check result is satisfactory and NG when it is not. HARD FLOW OK NG

10.RS-232C HARD FLOW:

NG


11.AD DATA CHECKThis menu is used to display the A/D conversion value of the main Microprocessor which detects panel keys of the main unit and protection functions in using the sub-menu. During signal processing, the condition before execution is maintained. When K0/K1 menu is selected, keys become non-operable due to detection of the values of all keys. However, it is possible to move to the next DIAG menu by turning the PROGRAM knob of the main unit. * The figures in the diagram are given as reference only.

11.AD DATA CHECK M i c r o p r o c e s s o r A / D K0/K1 PROGRAM

DC (Power supply voltage protection detection) DC: DC detect protection value (Normal value: 3 to 33) * If DC is out of the normal value range, the protection function works to turn off the power. (Reference voltage: 5V=255)

DC DC: 333 DC 5V=255

11.AD CHECK DC:019

PS1/PS2 (Power supply voltage protection detection) Power supply voltage protection value (Normal value: PS1: 54 to 87, PS2: 68 to 104) PS1: Detects +BDV, +BVA, +12V, -12V, +5D2, +2.5D. PS2: Detects +9V, +3.3VD ,+5VA and -5VA. * If PS is out of the normal value range, the protection function works to turn off the power. (Reference voltage: 5V=255)

PS1/PS2 PS1: 54-87PS2: 68-104 PS1: + B D V+ B V A - B V A+ 1 2 V - 1 2 V + 5 D 2 +2.5D PS2: +9V+3.3VD+5VA-5VA PS 5V=255

11.AD CHECK PS1:067PS2:084

36

RX-V2700/DSP-AX2700 TM1/TM2 (temperature detection) Temperature detected value (Normal value: 10 to 83) U, C, R, T, K, A, B, G, E models (Normal value: 10 to 78) L model TM1: Detects the temperature of the heat sink at the left side (power transformer side) TM2: Detects the temperature of the heat sink at the right side (volume side) (Reference voltage: 5V=255) TM1/TM2 10-83 TM1: TM2: 5V=255

11.AD CHECK TM1:051TM2:051


OUTLVL (Power limiter output level) Total value of amplifier output of each channel The voltage at 141 pin of IC402 is displayed with 5V/255 as a standard.

OUTLVL IC4021415V/255

11.AD CHECK OUTLVL:000

LMTCNT (Limiter control value) The voltage at 3 pin of IC402 is displayed with 5V/255 as a standard.

LMTCNT IC40235V/255

11.AD CHECK LMTCNT:255

AMPRELAY (Amp. Power relay control) The output condition of the power relay of the amplifier section is displayed.

AMPRELAY Amp. Power relay control

11.AD CHECK AMPRELAY:H

Display RY250 (MAIN P.C.B.) RY251 (MAIN P.C.B.) H (HIGH) ON OFF M (MID) OFF ON L (LOW) OFF OFF

MODEL Model detection value (Reference voltage: 5V=255)

MODEL 5V=255

11.AD CHECK MODEL:000Model Value RX-V2700/DSP-AX2700 0-64 RX-V1700/DSP-AX1700 65-191 HTR-6090 192-255

37

RX-V2700/DSP-AX2700 DESTINATION Destination detection value (Reference voltage: 5V=255) DESTINATION 5V=255

11.AD CHECK DEST:027Destination J C U R T Value 0 27 54 81 104 Destination K A B, G, E L Value 128 152 208 228


PANEL KEY (K0/K1) (Panel key of main unit) A/D of the key fails to function properly when the standard value is deviated by 4. In this case, check the constant of partial pressure resistor, solder condition, etc. Refer to table. (Reference voltage: 5V=255)

PANEL KEY (K0/K1) A/D4 5V=255

11.AD CHECK K0:255 K1:255

RX-V2700 (U, C, R, T, K, A, B, G, E, L models)Display 0+4 264 514 774 1044 1294 1544 1794 2054 2304 255 KEY0 NIGHT ZONE CONTROLS TUNING MODE MEMORY FM/AM PRESET/TUNING PRESET/TUNING PRESET/TUNING KEY OFF KEY1 STRAIGHT/EFFECT A/B/C/D/E TONE CONTROL AUDIO SELECT PURE DIRECT KEY OFF

DSP-AX2700 (J model)Display 0+4 264 514 774 1044 1294 1544 1794 2054 2304 255 K0 NIGHT TUNING MODE MEMORY FM/AM PRESET/TUNING PRESET/TUNING PRESET/TUNING KEY OFF K1 STRAIGHT/EFFECT A/B/C/D/E TONE CONTROL AUDIO SELECT PURE DIRECT KEY OFF

38

RX-V2700/DSP-AX2700

12.XM STATUS (U, C models)The output check of XM Radio Antenna is executed. 1k -1dB/44.1k The test tone (1kHz, -1dB/44.1kHz) is output.

12.XM STATUS UC modelsXM Radio Antenna 1k -1dB/44.1k 1kHz-1dB/44.1kHz

12.XM STATUS 1k - 1dB/441k -61dB/44.1k The test tone (1kHz, -61dB/44.1kHz) is output. 1k -61dB/44.1k 1kHz-61dB/44.1kHz


12.XM STATUS 1k -61dB/44Mute /44.1k Nothing is output. Mute /44.1k

12.XM STATUS Mute /44XM Tone/44.1k The XM tone (44.1kHz) is output. XM Tone/44.1k XM 44.1kHz

12.XM STATUS XM Tone/44ISO Tone/44.1k The ISO tone (44.1kHz) is output. ISO Tone/44.1k ISO 44.1kHz

12.XM STATUS ISO Tone/441k -1dB/32k The test tone (1kHz, -1dB/32kHz) is output. 1k -1dB/32k 1kHz-1dB/32kHz

12.XM STATUS 1k - 1dB/321k -61dB/32k The test tone (1kHz, -61dB/32kHz) is output. 1k -61dB/32k 1kHz-61dB/32kHz

12.XM STATUS 1k -61dB/32Mute /32k Nothing is output. Mute /32k

12.XM STATUS Mute /32XM Tone/32k The XM tone (32kHz) is output. XM Tone/32k XM 32kHz

12.XM STATUS XM Tone/3239

RX-V2700/DSP-AX2700 ISO Tone/32k The ISO tone (32kHz) is output. ISO Tone/32k ISO 32kHz

12.XM STATUS ISO Tone/32XM/DT Bus Power: OFF The power of XM module is turned off. XM/DT Bus Power: OFF XMOFF


12.XM STATUS Bus Power:OFF

13.IF STATUS (Input function status)Using the sub-menu, the status data is displayed one after another in the hexadecimal notation. During signal processing, the status before execution of this menu is maintained. * Numeric values in the figure example are for reference.

13.IF STATUS 16

IS1, 2 (Inside status) Indicates the status information of the microprocessor.

IS12

13.IF STATUS IS1:11000200005th byte 4th byte 3rd byte 2nd byte 1st byte

13.IF STATUS IS2:FF005 4 3 2 1

Digital input/output setting value Upper 4 bits: REC OUT selected / lower 4 bits: INPUT selectedValue 0 1 2 3 4 6 8 9 A

1 4bit REC OUT / 4bit INPUTChoice NONE OPT A OPT B OPT C OPT D OPT F COAX A COAX B COAX C Preset name V-AUX CD DVD D-TV CBL/SAT CD DVD DVR/VCR2

Fs information of reproduction signalDisplay Fs (kHz) 00 Analog 01 32 02 44.1 03 48 04 64 05 88.2 06 96

2Fs0A Unknown NRM 0B Unknown DBL 0C Unknown QUAD 0D Not defined

Audio code mode information of reproduction signalDisplay Audio Code 00 1+1 01 1/0 02 2/0 03 3/0 04 2/1 05 3/1 06 2/2 07 3/2

308 2/3 09 3/3 0A 0B 0C 0D OVER 6.1 MULTI PCE Unknown Unknown

40

RX-V2700/DSP-AX2700 Format information of reproduction signal *1: Analog processing used for digital reproduction is not possible because of a commercial bit or 4-ch audio reason.Display 00 01 10 20 21 22 23 50 51 54 58 5C 60 C0 C1 C4

4 *1 4ch

Signal format Analog (Unlock) Incorrect Digital (*1) PCM Audio Digital Data IEC1937 Data None PCM Unknown dts Red dts dts-ES MATRIX dts-ES DISCRETE dts-ES (Both flag) AAC Dolby Digital D.D. Karaoke D.D.6.1 (D.D.EX)


Signal processing status information *2: With digital signals other than 32kHz, 44.1kHz and 48kHz, through processing method is used for reproducible signals.bit7 bit6 bit5 bit4 MUTE request Red dts flashing 6.1/EX processing FULL MUTE (ON: 1)

5 *2 32kHz44.1kHz48kHz

bit3 bit2 Through & bypass (*2) bit1 bit0 dts analog mute

CS1-3 (Channel status): Indicates channel status information of the input signal (IEC60958).

CS1-3 Channel status : IEC60958

13.IF STATUS CS1:FFFFFFFFFF

13.IF STATUS CS3:FF321100

BS1-a: Indicates information of the bit stream included in the dts and Dolby Digital signals.

BS1-a: dtsDolby DigitalAAC

13.IF STATUS BS1:0000000000

13.IF STATUS BSa:00000000

TI1-2:

TI1-2:

13.IF STATUS TI1:0808000600

13.IF STATUS TI2:00

MTT: Mute Trigger

MTT: Mute Trigger

13.IF STATUS MTT:00120012FFByte No. 1 2 3 4 5 Function Mute condition Factor of the last mute Error count of YSS930-FSCNT Mute count by YSS930-FSCNT Error factor of down load of CS49329

41

RX-V2700/DSP-AX2700

14.iPodThis menu is used to test the DOCK connector without the iPod itself. After turning off the power, short between pins No. 14 (TX) and No. 18 (RX), between pins No. 1 (PWR) and No. 17 (ACCPOW) and between pins No. 4 (iPDET) and No. 8 (DGND). (Make sure that the power is turned off when shorting pins.) Start the DIAG function and select the menu. The check result is displayed according to the following display specifications.RX-V2700/ DSP-AX2700

14.iPodi P o d D O C K DOCK14 T X 1 8 R X 1 P W R 1 7 ACCPOW 4 iPDET 8 DGND

Note) Be sure to return the shorted locations to their original state.

15

16

17

18

9

10

11

12

13

14

3

4

5

6

7

8

1

19

20

21

2

14.iPod CHECK DOCK: NG NNNAll Y / Y = OK Others / = NG

DOCK

Check item / Is UART loop pack check result OK? /

Judgment / Display / YES Y UARTOK? NO N Is detect function of iPod Accessory Power OK? / IC2 (DSP P.C.B.) pin No. 45 state High = YES Y IC2 DSP P.C.B. 45pin Low = No iPod Accessory PowerOK N Is detect function of iPod installation to DOCK OK? / IC2 (DSP P.C.B.) pin No. 44 state Low = installed / Y DOCKiPodOK IC2 DSP P.C.B. 44pin High = not installed / N

42

RX-V2700/DSP-AX2700

15.NET CHECKIP Address Check IP address connection is checked.

15.NET CHECKIP Address Check IP

15.NET CHECK IP CHECK: NGOK: Connected (IP address obtained) IP NG: Unconnected


MAC Address Check MAC address information is checked.

MAC Address Check MAC

15.NET CHECK MAC CHECK:OKOK: Normal NG: Not written

16.USB CHECKUSB 1 Track The music data (first piece) recorded in the portable audio player connected to the USB terminal or in the USB flash memory is reproduced.

16.USB CHECKUSB 1 Track USB USB 1

16.USB CHECK USB 1 TRACK

USB 2 Track The music data (second piece) recorded in the portable audio player connected to the USB terminal or in the USB flash memory is reproduced.

USB 2 Track USB USB 2

16.USB CHECK USB 2 TRACK

43

RX-V2700/DSP-AX2700

17.PROTECTION HIST.The history of protection function is displayed. After selecting the sub-menu, press the STRAIGHT key, and the history will be erased. Last

17.PROTECTION HIST. STRAIGHT Last

17.PRTCT HIST. Last :NO PROTRX-V2700/ DSP-AX2700

History1

History1

17.PRTCT HIST. Hist1:NO PROTHistory2 History2

17.PRTCT HIST. Hist2:NO PROTHistory3 History3

17.PRTCT HIST. Hist3:NO PROT

18.DSP P.C.B. CHECKWhether the bus of DSP P.C.B. is connected properly or not is self-diagnosed. TI BUS TI (IC534) data bus check is executed.

17.DSP P.S.B. CHECKDSP P.C.B.

TI BUS TI IC534

18.DSP CHECK TI BUS:NoErYSS-930 BUS YSS-930 (IC550, IC552) data bus check is executed. YSS-930 BUS YSS-930 IC550IC552

18.DSP CHECK YSS BUS:NoErDisplay WAIT NoEr DATA RSCS ADDR Description Bus is being checked. No error detected. Data bus shorted or open. /RAS or /CAS shorted, or open. Address bus shorted or open. WAIT NoEr DATA RSCS ADDR /RAS/CAS

44

RX-V2700/DSP-AX2700

19.D-VIDEO P.C.B. CHECKWhether the bus of D-VIDEO P.C.B. is connected properly or not is self-diagnosed. ALL Check The synthetic judgment result is displayed. OK : No error detected NG : An error is detected No Check : Detection is not executed

19.D-VIDEO P.C.B. CHECKD-VIDEO P.C.B.

ALL Check OK NG No Check

19.DVIDEO CHK ALL:OKMicroprocessor/Flash Check The data bus check of Microprocessor (IC148) and Flash (IC147) is executed. OK : No error detected NG : An error is detected Microprocessor/Flash Check Microprocessor IC148 Flash IC147 OK NG


19.DVIDEO CHK M:OK F:OKI2C Read Check The Line check of I2C is executed. OK : 0 NG : 1 I2C Read Check I2C OK 0 NG 1

19.DVIDEO CHK I2C:00000000Error detection of IC146 / IC146 Error detection of IC138 / IC138 Error detection of IC137 / IC137 Error detection of IC102 / IC102 Error detection of IC101 / IC101 Error detection of IC120 and IC124 / IC120IC124 Error detection of IC123 and IC124 / IC123IC124

YGV BUS Check The data bus check of YGV619 (IC131) is executed.

YGV BUS Check YGV619 IC131

19.DVIDEO CHK YGV:NoErrorNo Error: No error detected / RAM_A : SDRAM (IC139) address bus error / SDRAM IC139 RAM_D : SDRAM (IC139) data bus error / SDRAM IC139 BUS : VIDEO microprocessor (IC148) bus error / IC148

20.HDMI INFORMATIONHDMI Model Name The model name of this unit written in HDMI module is displayed. RX-V2700 (U, C, R, T, K, A, B, G, E, L models) DSP-AX2700 (J model)

20.HDMI INFORMATIONHDMI Model Name HDMI RX-V2700 UCRTKABG EL models DSP-AX2700 J model

20.HDMI INFO HMN:RX-V270045

RX-V2700/DSP-AX2700 HDMI Product ID The product ID of this unit written in HDMI module is displayed. 310C (U, C, R, T, K, A, B, G, L models) 310B (J model) HDMI Product ID HDMIID 310C UCRTKABGL models 310B model J

20.HDMI INFO HPI:310CHDMI Vendor Name The vendor name (YAMAHA) of this unit written in the HDMI module is displayed. HDMI Vendor Name H D M I YAMAHA


20.HDMI INFO HVN:YAMAHA

21.HDMI SELECTUsing the sub-menu, the HDMI IN can be selected. With the audio input terminal selection set to HDMI (Fix), SPDIF or I2S is selected automatically according to the audio format which is used for HDMI input. Support Audio is set to others.

21.HDMI SELECTHDMI HDMI Fix HDMI SPDIFI2S Support Audio others HDMI NONE

HDMI NONE

21.HDMI SELECT HDMI NONEHDMI IN 1 HDMI IN 1

21.HDMI SELECT HDMI IN 1HDMI IN 2 HDMI IN 2

21.HDMI SELECT HDMI IN 2HDMI IN 3 HDMI IN 3

21.HDMI SELECT HDMI IN 3

22.HDMI UP CONV.The image signal is converted and output to HDMI OUT as follows. HDMI DecoderHDMI Decoder

22.HDMI UP CONV.HDMI OUT HDMI DecoderHDMI OUTS-Video Composite

HDMI IN

22.HDMI UPCONV HDMI DECODER

D-VIDEO IC101 SII9033

D-VIDEO IC102 SII9030-7

Component

Video Decoder D-VIDEO IC137 ADV7401 D-VIDEO IC131 YGV619

D-VIDEO IC146 MS2-NG

D-VIDEO IC138 ADV7322

S-Video

Composite

46

Component

D-VIDEO IC164 ABT1010

RX-V2700/DSP-AX2700 HDMI YGVHDMI YGV

HDMI YGV



Component

GUI Processor D-VIDEO IC137 ADV7401 D-VIDEO IC131 YGV619

D-VIDEO IC146 MS2-NG


S-Video

S-Video

Component


HDMI OUT

HDMI IN

22.HDMI UPCONV HDMI YGV


Composite

Composite

HDMI I/PHDMI I/P

HDMI I/P



Component

D-VIDEO IC146 MS2-NG D-VIDEO IC137 ADV7401 D-VIDEO IC131 YGV619


S-Video

S-Video

Composite

Composite

HDMI 720pHDMI 720p

HDMI 720p

D-VIDEO IC101 SII9033 Scalar (720P up scaling)


Component



S-Video

S-Video

Composite

Composite

HDMI 1080p Not applied to these models.

HDMI 1080p

22.HDMI UPCONV HDMI 1080pHDMI SMART ZOOMSMART ZOOM

HDMI SMART ZOOM

D-VIDEO IC101 SII9033 Scalar (Smart zoom)


Component



S-Video

S-Video

Composite

Composite

Component


HDMI OUT

HDMI IN

22.HDMI UPCONV SMART ZOOM

Component


HDMI OUT

HDMI IN

22.HDMI UPCONV HDMI 720p

Component

D-VIDEO IC164 De-Interlacer ABT1010 I/P (Interlace/Progressive)

HDMI OUT

HDMI IN

22.HDMI UPCONV HDMI I/P

47

RX-V2700/DSP-AX2700

23.VIDEOThe image signal is converted and output as follows. DIGITAL THR COMP

23.VIDEO DIGITAL THR COMP

23.VIDEO DIGITAL COMPDIGITAL THR COMP



D-VIDEO IC164 ABT1010 D-VIDEO IC146 MS2-NG


Component

D-VIDEO IC138 ADV7322 A-VIDEO IC225 LC74782 D-VIDEO IC137 ADV7401

S-Video

S-Video

Composite

Composite

DIGITAL THR CVBS

DIGITAL THR CVBS

23.VIDEO DIGITAL CVBSDIGITAL THR CVBS




Component


S-Video

S-Video

Composite

Composite

DIGITAL THR Y/C

DIGITAL THR Y/C

23.VIDEO DIGITAL Y/CDIGITAL THR Y/C




Component


S-Video

S-Video

Composite

Composite

48

Component

HDMI OUT

HDMI IN

Component

HDMI OUT

HDMI IN

Component

HDMI OUT

HDMI IN

RX-V2700/DSP-AX2700 DIGITAL BYPASS DIGITAL BYPASS

23.VIDEO DIGITAL BYPASSDIGITAL BYPASS




HDMI OUT

HDMI IN


Component


S-Video

S-Video

Composite

Composite

ANALOG BYPASS

ANALOG BYPASS

23.VIDEO ANALOG BYPASSANALOG BYPASS




Component


S-Video

S-Video

Composite

Composite

TEST PATTERN 1

TEST PATTERN 1

23.VIDEO TEST PATTERN 1TEST PATTERN 1


D-VIDEO IC164 ABT1010 IC146 MS2-NG TEST PATTERN


HDMI OUT

HDMI IN

IC146 TEST Pattern (480p/576p)

Component


S-Video

A-VIDEO IC225 LC74782


S-Video

Composite

Composite

Component

Component

HDMI OUT

HDMI IN

Component

49

RX-V2700/DSP-AX2700 TEST PATTERN 2 TEST PATTERN 2

23.VIDEO TEST PATTERN 2TEST PATTERN 2




HDMI OUT

HDMI IN

IC138 TEST Pattern (480i/576i)


Component

D-VIDEO IC138 ADV7322 TEST PATTERN

S-Video

A-VIDEO IC225 LC74782


S-Video

Composite

Composite

VIDEO INFO Displays the information of image signals being input.

VIDEO INFO

23.VIDEO VIDEO IN

---

24.ACCESS CHECKNot applied to this model. TI FLASH READ

24.ACCESS CHECK TI FLASH READ

24.BUS CHECK TI FLASH RTI FLASH WRITE TI FLASH WRITE

24.BUS CHECK TI FLASH WTI SDRAM READ TI SDRAM READ

24.BUS CHECK TI SDRAM RTI SDRAM WRITE TI SDRAM WRITE

24.BUS CHECK TI SDRAM WYGV READ YGV READ

24.BUS CHECK YGV BUS RYGV WRITE YGV WRITE

24.BUS CHECK YGV BUS W50

Component

RX-V2700/DSP-AX2700

25.FIRMWARE UPDATESelect this when writing the firmware. (Not applied to this model.) 232C MAIN Writing of MAIN.

25.FIRMWARE UPDATE 232C MAIN MAIN

25.FLASH 232C MAINRX-V2700/ DSP-AX2700

232C VIDEO Writing of VIDEO.

232C VIDEO VIDEO

25.FLASH 232C VIDEO232C TI Writing of DSP. 232C TI DSP

25.FLASH 232C TIUSB NET USB NET

25.FLASH 232C NET/USB UPDATE

26.SET INFOThe information on the model and destination is displayed. MODEL: V2700

26.SET INFO

MODEL: V2700

26.SET INFO MODEL:V2700DEST.: J, UC, R, T, K, A, BGE, L J, UC, R, T, K, A, BGE or L is displayed. DEST.: JUC R T K A BGE L JUCRTKABGEL

26.SET INFO DEST:UC

51

RX-V2700/DSP-AX2700

27.SOFT SWThis menu is used to switch the function settings on P.C.B. through the software to activate the product. The protection function follows the P.C.B. settings. When connected to AC or in the maker preset state, the unit is initialized to the P.C.B. setting. Display of each function after initialization varies depending on settings on P.C.B.. The operation mode can be changed by selecting the sub-menu and then using the STRAIGHT key.RX-V2700/ DSP-AX2700

27.SOFT SWP.C.B. P.C.B.AC P.C.B. P.C.B. STRAIGHT

SW MODE: PCB/SOFT PCB or SOFT can be selected.

SW MODE: PCB/SOFT PCBSOFT

27.SOFT SW SW MODE : PCB

TV FORMAT: NTSC/PAL NTSC or PAL can be selected. NTSC (U, C, R, K, J models) PAL (T, A, B, G, E, L models)

TV FORMAT: NTSC/PAL NTSCPAL NTSC UCRKJ models PAL TABGEL models

27.SOFT SW TV FORMAT:NTSC

AAC EXIST: EXIST/NOT EXIST or NOT can be selected. EXIST (J model) NOT (U, C, R, T, K, A, B, G, E, L models)

AAC EXIST: EXIST/NOT EXISTNOT EXISTJ model NOT UCRTKABGEL models

27.SOFT SW AAC : NOT

CSII EXIST: EXIST/NOT EXIST or NOT can be selected. EXIST (J model) NOT (U, C, R, T, K, A, B, G, E, L models)

CSII EXIST: EXIST/NOT EXISTNOT EXISTJ model NOT UCRTKABGEL models

27.SOFT SW CSII : NOT

52

RX-V2700/DSP-AX2700 RDS EXIST: EXIST/NOT EXIST or NOT can be selected. EXIST (B, G, E models) NOT (U, C, R, T, K, A, L, J models) RDS EXIST: EXIST/NOT EXISTNOT EXISTBGE models NOT UCRTKALJ models

27.SOFT SW RDS : NOT

XM EXIST: EXIST/NOT EXIST or NOT can be selected. EXIST (U, C models) NOT (R, T, K, A, B, G, E, L, J models)

XM EXIST: EXIST/NOT EXISTNOT EXISTU, C models NOT RTKABGELJ models


27.SOFT SW XM :EXIST

Neural Audio EXIST or NOT can be selected. EXIST (U, C models) NOT (R, T, K, A, B, G, E, L, J models)

Neural Audio EXISTNOT EXISTU, C models NOT RTKABGELJ models

27.SOFT SW NEURAL :EXIST

TMP TEST J/UC/RL J, UC, RTKA, BGE or L can be selected. J (J model) UC (U, C models) RTAK (R, T, K, A models) BGE (B, G, E models) L ( L model)

TMP TEST J/UC/RL JUCRTKABG J J model UC UC models RTKARTKA models BGE BGE models L L model

27.SOFT SW TMP TEST:UC

53

RX-V2700/DSP-AX2700

28.FACTORY PRESETThis menu is used to reserve and inhibit initialization of the back-up RAM. The signals are pro

Documents

RXV2700