Upload
others
View
3
Download
0
Embed Size (px)
Citation preview
Click to start
Screws
Coatings Head Styles Selection Guide ContactRange
Plasterboard Screws
Multi-Use Screws
Chipboard Screws
Metal ScrewsTimber Screws
Sheet Metal Screws
Decking Screws
Roofing Screws
Treated Pine Screws
Screws
Coatings Head Styles Selection Guide ContactRange
Plasterboard Screws
Bugle Head Needle Point
• For fixing plasterboard to timber, wall and ceilings, partitions
• Also used for light duty general fixing into timber and light gauge metal for a flush finish
• Available in Phillips Drive
Bugle Head Drill Point
• For fixing plasterboard to metal purlins
• Available in Phillips Drive
Bugle shaped head countersinks neatly into plasterboard without crushing the core, or tearing the face paper
Sizes: 6G, 7G, 8G, 10GAvailable Lengths: 20, 25, 30, 40, 50, 60, 65, 75, 100mmPack Qty: 50, 100, 500, 1000 (smaller pack sizes also available)Material/Coating: Gold Passivated and Zinc Plated
Sizes: 6GAvailable Lengths: 25, 30, 45mmPack Qty: 100, 500, 1000Material/Coating: Gold Passivated and Zinc Plated
Coatings Head Styles Selection Guide ContactRange
Chipboard Screws Ribbed, countersunk head provides a clean flush finish by removing chipboard particles prior to countersinking
Countersunk Rib Head Needle Point
• Specifically designed for use in Chipboard/Particle Board/MDF for a flush finish
• Ideal for fixing cabinets, furniture, kitchens, office partitioning etc
• Available in Phillips or Square Drive
Sizes: 6G, 8G, 10GAvailable Lengths: 20, 25, 28, 30, 32, 35, 40, 45, 50, 57, 60, 65, 75, 100mmPack Qty: 50, 100, 250, 500, 1000 (smaller pack sizes also available)Material/Coating: Gold Passivated and Zinc Plated
Coatings Head Styles Selection Guide ContactRange
Coated to protect against the chemicals present in treated timber
Countersunk Rib Head Needle Point
• Used for general fixing to treated timber, such as trellis, outdoor furniture, fencing, lattice etc
• Resists the corrosive effects of timber treatments
• Available in Phillips and Square Drive
Sizes: 6G, 8G, 10GAvailable Lengths: 20, 25, 30, 32, 35, 40, 45, 50, 57, 60, 65, 75, 100mmPack Qty: 50, 100, 250, 500, 1000 (smaller pack sizes also available)Material/Coating: TUFCOTE® and Climacoat 3
Note: Not suitable for Decking
Treated Pine Screws
Coatings Head Styles Selection Guide ContactRange
Decking Screws
Treated Pine Decking Stainless Steel DeckingComposite Decking
Steel Joists Decking Self Drilling Decking Hidden Decking Screw
XL Head Decking Screw
Coatings Head Styles Selection Guide ContactRange
Treated Pine Decking Screw
Countersunk Rib Head Square Drive
• Suitable for fastening decking including treated pine and hardwood timbers
• Pre-drilling and pre-countersinking required for hardwoods
Sizes: 10G Available Lenths: 40, 45, 50, 65mmPack Qty: 100, 250, 500, 1000Material/Coating: Hardened Carbon Steel Climacoat 3
Coatings Head Styles Selection Guide ContactRange
Stainless Steel Decking Screw
Countersunk Rib Head Square Drive
• Suitable for fastening decking including treated pine and hardwood timbers
• Pre-drilling and pre-countersinking required for hardwoods
Sizes: 8G, 10GAvailable Lengths: 40, 45, 50, 65mmPack Qty: 50, 250, 500, 1000Material/Coating: Stainless Steel Grade 304 & 316
Coatings Head Styles Selection Guide ContactRange
Self Drilling Decking Screw
Countersunk Rib Head Square Drive
• Suitable for fastening decking including treated pine and hardwood timbers
• Self Drilling. No need to pre-drill and pre-countersink
Sizes: 12G Available Lengths: 50, 65mmPack Qty: 50, 500Material/Coating: Stainless Steel Grade 304
Coatings Head Styles Selection Guide ContactRange
XL Head Decking Screw
Countersunk Rib Head Star Drive
• Designed specifically for fastening 140mm wide hardwood decking boards
• Pre-drilling and pre-countersinking required for hardwoods
Sizes: 12GAvailable Lengths: 50, 65mmPack Qty: 50, 250Material/Coating: Stainless Steel Grade 304
Coatings Head Styles Selection Guide ContactRange
Steel Joists Decking Screw
Countersunk Rib Head Square Drive
• Designed specifically for fastening timber decking to steel joists between 1.2mm to 2.4mm thick and HRS 1.5mm to 3.0mm thick
• Self Drilling. No Pre-drilling and pre-countersinking required
Size: 10G x 47mmPack Qty: 500Material: Stainless Steel Grade 304
Coatings Head Styles Selection Guide ContactRange
Composite Decking Screw
Embedding Head Star Drive
• Designed specifically for fastening composite decking boards to timber joists
• Self drilling point ensures fast installation, while reverse thread eliminates ‘mushrooming’
Size: 10G x 64mmPack Qty: 500Material/Coating: Hardened Carbon Steel/Brown Coating
Coatings Head Styles Selection Guide ContactRange
Hidden Decking Fastening System
Construction of a beautiful, fastener-free deck surface
• Provides a distinctive side-angle entry that secures solid or grooved Deck Boards directly to the joist, reducing board movement and allowing the screws to be hidden
• A unique trim head design allows for a less visible point of entry and the reverse rake tip removes deck material as it bores, allowing the screw to penetrate the board without splitting
Coatings Head Styles Selection Guide ContactRange
• Heavy-duty, contractor grade tool
• Clamping action grips deck board
• Dual screw guides fasten both sides of board with single tool placement
Hidden Decking Fastening System
Coatings Head Styles Selection Guide ContactRange
Hidden Decking Fastening System
Pro-Tech Coated Hardened Carbon Steel
• ACQ-compatible ProTech coating passes 1500 hour salt spray test; Australian equivalent Class 4
• No pre-drilling required
316 Stainless Steel – Black
• 316 Stainless Steel offers ultimate corrosion resistance recommended for coastal environments
• No pre-drilling required
Size: 7GAvailable Lengths: 48, 60mmPack Qty: 350, 700, 1750
Size: 7GAvailable Lengths: 48, 60mmPack Qty: 350, 700, 1750
Coatings Head Styles Selection Guide ContactRange
Timber Screws
Bugle Head Batten Button Stitching Head Countersunk Head
Wafer Head Self Embedding Head Hexagon Head (no seal)
Hexagon Head (with seal) Construction Screw
Coatings Head Styles Selection Guide ContactRange
Bugle Head Batten
Type 17 Point Internal Hex Drive
• Self drilling Type 17 point incorporates a sharp hardened point with end slot which eliminates timber expansion and minimises the splitting of timber
• Fixes into timber and thin steel thicknesses of up to 0.75mm
• Ideal for outdoor building purposes, such as pergolas, fencing, boardwalks
Size: 14GAvailable Lengths: 25, 50, 65, 75, 85, 100, 125, 150, 175, 200mmPack Qty: 20, 25, 50, 100, 250, 500Material/Coating: Zinc Plated, Gold Passivated, Tufcote®, Climacoat 3, Galvanised Class 3, Zinc Alloy 3, Stainless Steel 304 and 316
Coatings Head Styles Selection Guide ContactRange
Countersunk Head
Type 17 Point Phillips Drive
• Self drilling Type 17 point incorporates a sharp hardened point with end slot which eliminates timber expansion and minimises the splitting of timber
• Fixes into timber and thin steel thicknesses of up to 0.75mm
• Ideal for jobs needing a flush finish, such as hinges, furniture, brackets
Size: 6G, 8G, 10G Available Lengths: 25, 30, 40, 50mmPack Qty: 50, 440 (smaller pack sizes also available)Material/Coating: Zinc Plated, Gold Passivated, Galvanised Class 3
Coatings Head Styles Selection Guide ContactRange
Self Embedding Head
Type 17 Point Phillips Drive
• Self drilling Type 17 point incorporates a sharp hardened point with end slot which eliminates timber expansion and minimises the splitting of timber
• Fixes into timber and thin steel thicknesses of up to 0.75mm
• Ideal for general fixings, such as walls, particle board flooring
Size: 8G x 40mmPack Qty: 50Material/Coating: Zinc Plated
Coatings Head Styles Selection Guide ContactRange
Button Head Stitching
Type 17 Point Phillips Drive
• Self drilling Type 17 point incorporates a sharp hardened point with end slot which eliminates timber expansion and minimises the splitting of timber
• Fixes into timber and thin steel thicknesses of up to 0.75mm
• Ideal for applications where a broad flat head is needed, such as shade cloth, foil insulation, wire mesh
Size: 8GAvailable Lengths: 15, 20, 25, 30mmPack Qty: 100, 500, 1000 (smaller pack sizes also available)Material/Coating: Galvanised Class 3 and Gold Passivated
Coatings Head Styles Selection Guide ContactRange
Wafer Head
Type 17 Point Phillips Drive
• Self drilling Type 17 point incorporates a sharp hardened point with end slot which eliminates timber expansion and minimises the splitting of timber
• Fixes into timber and thin steel thicknesses of up to 0.75mm
• Ideal for applications where a low profile head is required, such as signs, electrical fixings
Size: 10GAvailable Lengths: 25, 35, 45mmPack Qty: 50, 100 (smaller pack sizes also available)Material/Coating: Zinc Plated, Gold Passivated, Galvanised Class 3
Coatings Head Styles Selection Guide ContactRange
Hex Head (no seal)
Type 17 Point External Hex Drive
• Self drilling Type 17 point incorporates a sharp hardened point with end slot which eliminates timber expansion and minimises the splitting of timber
• Fixes into timber and thin steel thicknesses of up to 0.75mm
Range
Size: 10G, 12G, 14GAvailable lengths: 50, 65, 75, 100, 125, 150mmPack Qty: 25, 250, 500, 1000 (smaller pack qty available)Material/Coating: Climaseal 3 and 4, Climeseal 4 Painted
Size: 10G, 12GAvailable lengths: 25, 30, 40mmPack Qty: 50, 100, 500, 1000 (smaller pack qty available)Material/Coating: Gold Passivated, Galvanised Class 3, Zinc Alloy 3, Climaseal 3
Partial Thread Full Thread
Coatings Head Styles Selection Guide ContactRange
Hex Head (with seal)
Type 17 Point External Hex Drive
• Self drilling Type 17 point incorporates a sharp hardened point with end slot which eliminates timber expansion and minimises the splitting of timber
• Fixes into timber and thin steel thicknesses of up to 0.75mm
Size: 12G, 14GAvailable lengths: 25, 30, 45, 50, 65, 75, 90, 100, 125mmPack Qty: 25, 50, 100, 250, 500, 1000 (smaller pack qty available)Material/Coating: Galvanised Class 3, Climaseal 3 and 4
Size: 10G, 12G, 14GAvailable lengths: 25, 30mmPack Qty: 50, 100, 500Material/Coating: Galvanised Class 3, Climaseal 3
Partial ThreadIdeal for crest fixing roofing profiles to timber battens
Full ThreadIdeal for valley fixing wall cladding
Coatings Head Styles Selection Guide ContactRange
Construction Screw
Type 17 Point Hex Drive, Washer Head
• Built for the more demanding project, Buildex® Timber Construction Screws have been designed and engineered to deliver superior speed, strength and performance when fastening heavy timbers
• Ideal for pergolas, sleepers, gates, and fencing, the Timber Construction Screw has been designed with a number of unique features which offer optimum performance when fastening timber to timber
Size: 16GAvailable lengths: 75, 100, 125mmPack Qty: 20, 100, 250Material/Coating: Climacoat 3, Zinc Alloy 3
Coatings Head Styles Selection Guide ContactRange
Metal Screws
Bugle Head Teks® Button Head Teks® Hex Head Teks® (with seal)
Countersunk Head Teks® Wafer Head Teks® Metal Batten Zips®
Countersunk WingTeks® FibreTeks®
Coatings Head Styles Selection Guide ContactRange
Bugle Head Teks®
• Self drilling screws with a hardened drill point that will drill and thread into structural steel and mild steel
• Ideal for fixing plasterboard to metal
• Available in Phillips Drive
Size: 6GAvailable Lengths: 25, 30, 45mmPack Qty: 50, 100, 500, 1000Material/Coating: Zinc Plated & Gold Passivated
Coatings Head Styles Selection Guide ContactRange
Countersunk Head Teks®
Size: 8G, 10G Available Lengths: 20, 25, 30, 35, 40, 50, 65mm Pack Qty: 25, 50, 500, 1000 (smaller packs available)Material/Coating: Zinc Plated, Gold Passivated, Galvanised Class 3, Climacoat 3
• Self drilling screws with a hardened drill point that will drill and thread into structural steel and mild steel
• Ideal for jobs needing a flush finish, such as fencing, gates, hinges
• Available in Phillips Drive
Coatings Head Styles Selection Guide ContactRange
Countersunk WingTeks®
Size: 6G, 8G, 10G, 14GAvailable Lengths: 30, 35, 40, 45, 50, 55, 60, 65, 75mm Pack Qty: 25, 50, 100, 250, 500, 1000Material/Coating: Zinc Plated, Gold Passivated, Galvanised Class 3, Climacoat 3
• Ideal for fixing timber and composite boards to metal, and prevents timber rising to the top of the screw while the metal is being drilled
• Reaming cutters in the underside enables the head of the fastener to self-embed for a flush or recessed finish
• Available in Phillips Drive
Coatings Head Styles Selection Guide ContactRange
Button Head Teks®
Size: 8GAvailable Lengths: 12, 16, 20, 25, 32mmPack Qty: 25, 50, 100, 250, 500, 1000 (smaller packs available)Material/Coating: Zinc Plated, Gold Passivated, Galvanised Class 3, Zinc Alloy 3
• Self drilling screws with a hardened drill point that will drill and thread into structural steel and mild steel
• Ideal for applications where a broad flat head is needed, such as foil sarking, insulation panels, fascia bracket clips etc
• Available in Phillips Drive
Coatings Head Styles Selection Guide ContactRange
Wafer Head Teks®
Size: 8G, 10GAvailable Lengths: 12, 16, 22, 25, 30, 32mmPack Qty: 25, 50, 100, 250, 500, 1000 (smaller packs available)Material/Coating: Zinc Plated, Gold Passivated, Galvanised Class 3, Zinc Alloy 3, Climaseal 3
• Self drilling screws with a hardened drill point that will drill and thread into structural steel and mild steel
• Ideal for applications where a low profile head is required, such as metal deck clips, electrical fittings, signs, sheet metal
• Available in Phillips Drive
Coatings Head Styles Selection Guide ContactRange
FibreTeks®
Size: M4.8-18Available Lengths: 25, 30mmPack Qty: 100, 500Material/Coating: Climaseal 4
Countersunk Rib Head Phillips Drive
• Specifically designed for fitting non-compressed fibre cement sheeting to steel sections up to 1.2mm thick
• Typical applications includes eaves, fascia, wet areas, ceilings, and interior walling and cladding
Coatings Head Styles Selection Guide ContactRange
Hex Head Teks® (with seal)
Size: 12G, 14GAvailable Lengths: 50, 65, 75mmPack Qty: 25, 50, 100 (smaller pack sizes available)Material/Coating: Galvanised Class 3, Climaseal 3 and 4
• Self drilling screws with a hardened drill point that will drill and thread into structural steel and mild steel
• Ideal for fixing metal to metal, such as fences, signs, trailers
• Available in External Hex Drive
Size: 8G, 10G, 12G, 14G Available Lengths: 12, 16, 20, 22, 25, 30, 35, 45mmPack Qty: 50, 100, 500, 1000Material/Coating: Zinc Plated, Climaseal 3 and 4, Climaseal 3 Painted
Partial Thread Full Thread
Coatings Head Styles Selection Guide ContactRange
Metal Batten Zips®
• For fastening thin metal battens to timber trusses and steel purlins up to 1.5mm thick
• Available in External Hex Drive
Size: M5.5 x 40mmPack Qty: 100, 1000Material/Coating: Zinc Alloy 3 Galvanised
Coatings Head Styles Selection Guide ContactRange
Roofing Screws
Timber Timber or Metal Metal
Hex Head Teks® (with seal)Hex Head (with seal) Roof Zip® HiGrip® (with seal)
Polyzips® HiGrip® (with seal)Cyclone Assemblies
Coatings Head Styles Selection Guide ContactRange
Hex Head (with seal)
Roofing To Timber External Hex Drive
• Self drilling screws designed to drill and thread for quick installation, with a watertight seal to prevent water from entering the roof cavity
• Ideal for crest fixing roofing profiles to timber battens
• Available in full or part thread
Size: 12G, 14GAvailable lengths: 45, 50, 65, 75, 90, 100, 125mmPack Qty: 25, 50, 100, 250, 500, 1000Material/Coating: Galvanised Class 3, Climaseal 3 and 4
Size: 10G, 12G, 14GAvailable lengths: 25, 30mmPack Qty: 50, 100, 500Material/Coating: Galvanised Class 3, Climaseal 3 and 4
Partial ThreadIdeal for crest fixing roofing profiles to timber battens
Full Thread Ideal for valley fixing wall cladding
*HiGrip® available in 50 and 65mm
Coatings Head Styles Selection Guide ContactRange
Roof Zip® Hex Head
Roofing and Cladding to Timber External Hex Drive
• RoofZips® are used for fixing steel roof sheeting to timber, to thin metal battens or steel purlins up to 1.5mm thick. The patented washer design prevents washer spewing out from under screw head
• HiGrip® from Buildex® is a revolutionary design in roof fasteners that has a secondary thread located at the top of the shank under the washer face to prevent indentation around the fastener that is typically found in ordinary fasteners which causes water entry
• Ideal for crest fixing corrugated and square rib roofing profiles to timber battens or steel purlins
Size: M6Available Lengths: 50, 65mmPack Qty: 100, 500, 1000Material/Coating: Climaseal 4, Climaseal 3 and 4 painted
Coatings Head Styles Selection Guide ContactRange
Poly Zips®
Polycarbonate Roofing To Timber Or Metal External Hex Drive
• With a Dome Washer and Cutter, Poly Zips® are ideal for fixing polycarbonate roofing to timber and thin metal battens up to 1.9mm thick
• Climaseal 3 coated that meets real world testing to AS3566 Class 3
Size: M6.5 x 50mmPack Qty: 36, 250Material/Coating: Climaseal 3
Coatings Head Styles Selection Guide ContactRange
Hex Head Teks® (with seal)
Roofing and Cladding to Metal External Hex Drive
• Self drilling screws designed to drill and thread for quick installation, with a watertight seal to prevent water from entering the roof cavity
• Ideal for fixing roofing profiles and wall cladding to steel purlins
Size: 12G, 14GAvailable Lengths: 25, 50, 65, 75mmPack Qty: 25, 50, 100Material/Coating: Climaseal 3 and 4
Size: 10G, 12G, 14GAvailable Lengths: 16, 20, 22, 25, 45mmPack Qty: 25, 50, 100, 500, 1000Material/Coating: Climaseal 3 and 4, Climaseal 3 Painted
Partial Thread Full Thread
Coatings Head Styles Selection Guide ContactRange
Hex Head HiGrip® (with seal)
Hex Head Teks®
Roofing To Metal External Hex Drive
• HiGrip® from Buildex® is a revolutionary design in roof fasteners that has a secondary thread located at the top of the shank under the washer face to prevent indentation around the fastener that is typically found in ordinary fasteners which causes water entry
• Ideal for crest fixing corrugated and square rib roofing profiles to steel purlins
Size: 12GAvailable Lengths: 35, 45, 50mmPack Qty: 50, 100, 250, 1000Material/Coating: Climaseal 3
Coatings Head Styles Selection Guide ContactRange
Cyclone Assemblies
Fixing to Timber & Metal
ROOF-LOK® – Type 17, Roof Zips® & Metal Teks®
• Cyclonic assembly for square and corrugated roofing profiles
High Rib Profiles – Type 17 & Metal Teks®
• Fixing high rib roofing profiles to timber battens and steel purlins in cyclonic areas.
Ridge Cap Assemblies – Type 17 & Metal Teks®
• For ridge cap assembly of roofing profiles to timber battens and steel purlins in cyclonic areas
Size: 12G, 14GAvailable Lengths: 32, 45, 47, 50, 53, 55, 65, 75, 78, 95, 100, 125, 150, 175, 200, 205, 230, 300mmPack Qty: 250Material/Coating: Climaseal 3, Climaseal 4, Climaseal 5
Coatings Head Styles Selection Guide ContactRange
Sheet Metal Screws
Sizes: 4G, 6G, 8G, 10G, 12G, 14GAvailable Lengths: 6, 9, 12, 15, 18, 25, 30, 32, 38, 50mmPack Qty: 25, 50, 100 (smaller pack sizes available)Material/Coating: Zinc Plated & Stainless Steel 304
A pan head screw which allows for a low profile head finish
Self Tapping Screws
• Ideal for fixing into thin metal or into timber, or joining sheet metal together
• Pilot Hole Required – Manual Driving is recommended over power driving to ensure thread does not pull through thin steel
• Available in a slotted Pan Head Drive
Coatings Head Styles Selection Guide ContactRange
Multi Use Screws All-purpose self-drilling screws for general fixings around the home, into timber and thin metal
Sizes: 7G, 8GAvailable Lengths: 20, 25, 30, 40, 45, 50mmPack Qty: 50, 100, 500Material/Coating: Zinc Plated
Sizes: 8GAvailable Lengths: 13, 15, 20, 25, 30, 32, 40mmPack Qty: 100, 1000Material/Coating: Zinc Plated & Zinc Alloy 3 Gal
Sizes: 6G, 7GAvailable Lengths: 12, 20, 25, 30, 40, 50mm Pack Qty: 100Material/Coating: Zinc Plated
Bugle Head Needle Point
• Recommended for all general fixing into timber and light gauge metal
• Ideal for applications where a flush finish is required
• Available in Phillips Drive
Button Head Needle Point
• Recommended for jobs where a broad, flat head is needed
• Ideal for applications such as shade cloth, foil insulation, wire mesh etc
• Available in Phillips Drive
Pan Head Needle Point
• Ideal for fixings, such as spotlights, doors, security alarms, light switches etc
• Available in Phillips Drive
Range Head Styles Selection Guide ContactCoatings
Coating Selection
InternalZinc Plated Gold Passivated
Treated Pine Tufcote®
Climacoat 3
ExternalGalvanised Zinc Alloy 3 Climaseal 3Climaseal 4
Treated Pine Tufcote®
Climacoat 3
Range Head Styles Selection Guide ContactCoatings
Coating Selection – Internal
Zinc Plated (ZP)An electroplated zinc coating provides a barrier to corrosion degradation
Gold Passivated (GP)
Consists of a chromate film layer over the zinc for a higher corrosion protection
Corrosion ClassesClass 1: For internal useClass 2: For internal use where significant levels of condensation occursClass 3: For external use in mild industrial and moderate marine applicationsClass 4: For external use in moderate and severe marine environments (generally from 100m to 300m from the beach front)
Range Head Styles Selection Guide ContactCoatings
Tufcote®Suitable for treated pine useConsists of a sacrificial zinc base coat with organic top coat for protection against timber treatments
Climacoat® (CC)Suitable for treated pine use Consists of a sacrificial zinc base coat with organic top coat for protection against timber treatments
Coating Selection – Treated Pine
Corrosion ClassesClass 1: For internal useClass 2: For internal use where significant levels of condensation occursClass 3: For external use in mild industrial and moderate marine applicationsClass 4: For external use in moderate and severe marine environments (generally from 100m to 300m from the beach front)
Range Head Styles Selection Guide ContactCoatings
Coating Selection – External
Galvanised (GAL) Class 3
Mechanically applied zinc, suitable for external use
Zinc Alloy 3Class 3
Similar coating to Tin/Zinc, suitable for external use
Climaseal 3Class 3
A coating that meets AS3566.2-2002 Class 3 under real world testing
Climaseal 4Class 4
A coating that meets AS3566.2-2002 Class 4 under real world testing
Corrosion ClassesClass 1: For internal useClass 2: For internal use where significant levels of condensation occursClass 3: For external use in mild industrial and moderate marine applicationsClass 4: For external use in moderate and severe marine environments (generally from 100m to 300m from the beach front)
Range Coatings Selection Guide ContactHead Styles
Screw Head Styles
Hexagon Head (Washer Face & Without Washer Face)
• To accommodate a watertight sealing washer (with Washer Face)
• Greater strength & ease of torque input
Bugle Head
• Smooth curved surface under head designed to avoid damage to plasterboard
• #2 Phillips Cross Head Bit
Bugle Head Batten
• For a flush finish into timber• For fastening battens to timber rafters• 5mm internal hexagon drive bit
Washer Head
• Broad profile head provides a strong and secure connection in timber applications
• 5mm internal hexagon drive bit
Countersunk/Ribbed Countersunk Head
• For countersinking into timber for a flush or recessed finish
• Also suitable for metal • #2 Phillips Cross Head Bit or #2 Square Drive Bit
Wafer Head
• A versatile low head style used for many fastening applications
• Low head design eliminates risks of dimpling the roof when the tradesperson walks on it
• #2 Phillips Cross Head Bit
Pan Head
• Round head with a flat underside fully threaded for accurate clamping
• Designed for applications fixing against metal surfaces
• #2 Phillips Cross Head Bit
Button Head
• Low profile head enables fasteners to sit level on surface
• #2 Phillips Cross Bit or #2 Square Bit Drive
Range Coatings Head Styles ContactSelection Guide
Roofing Decking
Range
Selection Guide
Range Coatings Head Styles ContactSelection Guide
Fixing to: Timber
Pine
0.55mm0.75mm1.2mm
1.5mm 1.9mm
Hardwood
Extreme hardwoods (Jarrah, Red Gum) & re-roofing applications
Fixing to: Steel
Ideally suited for this application
Works well in this application
Works into this application – Install at low revs, using high end-load pressureContact Buildex Technical Help Desk for more information
Range
Roof Zip® Application Table
Range Coatings Head Styles ContactSelection Guide
Climacoat® Decking Screws are suitable for fixing treated pine decking timbers
Stainless Steel Decking Screws offer excellent protection against corrosion in all decking timbers
Good corrosion protection Superior corrosion protection
Climacoat® Decking Screws
302/304 Grade
Stainless Steel Decking Screws
Stainless Steel Decking Screws
316 Marine Grade
Range
Decking Finish/Materials Selection
Range Coatings Head Styles ContactSelection Guide
For Hardwood (Merbau)
• 10G stainless steel screws, or 316 Grade stainless steel
• 304 Grade stainless steel for all other areas
• Square drive head for easier installation
For Treated Timbers
• 10G Climacoat® or 8G stainless steel screws
• Climacoat® ACQ coated specifically for treated timbers
• Square drive head for easier installation
For Composite Decking
• 10G stainless steel screws, or 316 Grade stainless steel for areas close to salt water
• 304 Grade stainless steel for all other areas
• Square drive head for easier installation
Handy HintsHow many fasteners: Approximately 50 per square metre (46 each 10 lineal metres)
What length: More than 2 times timber thickness (e.g. 19mm timber, use 50mm screws)
Pre drilling: For best results, it is recommended to pre drill and pre countersink holes
Coastal areas: It is recommended that 316 grade stainless steel be used
Decking Screws Selection
Range Coatings Head Styles Selection Guide Contact
Contact
Bunnings welcome the opportunity to quote your next job.
Please contact your local Bunnings Account Manager or call 133 062.