INSULATION PRODUCTS

Selection Guide & Reference Chart (Since 2000)

www.tickorea.com

Mastics and Coatings 2-3

Adhesives 4-5

Sealants 6

Cements 7

section

2 TIC CORPORATION

Product Name

Vapor Sealing Insulation Facing

and Jacketing (FSK, ASJ, FRK)

Lagging Adhesive/

Coating

Fiberglass and Mineral Wool

Rigid Insulation (Cellular Glass, PIR, Phenolic)

PolystyreneCoating1

CalciumSilicate

Vinyl MasticTIC 1010 ○ ○ ○

H.I MasticTIC 1030 ○ ○ ○

WB Vapour Barrier Coating & MasticTIC 2010/2015 ● ● ● ●

Weather Barrier Coating & MasticTIC 2030/2035 ○ ● ○ ●

Anti Abrasive CoatingTIC 2050 ●

PVA Adhesive/CoatingTIC 2060 ● ○ ○ ○

Resistance CoatingTIC 2070 ● ● ○ ○ ○

Anti-Fungus CoatingTIC 2070AF ● ● ○ ○ ○

C.I MasticTIC 3010 ○ ●

F.R.C.I MasticTIC 3020 ○ ●

CSM Vapour Barrier Coating & Mastic TIC 4010/4015 ○ ●

Vapour Barrier Coating & MasticTIC 4050/4055 ● ●

Hs Vapour Barrier CoatingTIC 4060 ● ● ○

Vapour-Silver MasticTIC 4075 ●

Heat Resistance CoatingTIC 4085 ●

Vapor Barrier Membrane and Jacketing

Barrier WrapTIC Bwrap PA 201 ● ○

Barrier Wrap(N.F.)TIC Bwrap PB 201 ● ○

Barrier Wrap(N.F.)TIC Bwrap PB 209 ● ○

Cryogenic Wrap(N.F)TIC Bwrap PB210 ● ○

Mastics and Coatings

● BEST This guide is provided as a quick reference. Please see product data sheet for specific test methods, installation methods and additional information.

○ GOOD 1 Always choose white colored coating for exterior use on polystyrene insulation, Do not use solvent based products with polystyrene.

3TIC CORPORATION

General DescriptionType

ofVolatile

PermeanceValue as

Measured inUS Perms2

Flash Point

An emulsion type of coating product for finishing process, which has excellent resistance to chemical and any outdoor circumstances especially to severe weather conditions, has been generally used to Insulation.

Water ≤ 3.0 None

Economical asphalt emulsion. A protective weather coat that is easy to apply and will not shrink or crack.Use on hot operating, exterior insulation systems.

Water ≤ 1.0 None

A water-based vapor retarder for indoor or outdoor use. Low odor, non-toxic, and low VOC.Use on cold operating systems.

Water≤ 0.013≤ 0.012

None

High performance, general purpose water-based, weather barrier mastic for indoor and outdoor use. Fire and chemical resistive. Excellent application properties for heavy duty applications. UL CLASSIFIED

Water ≤ 1.0 None

High solids, fire resistive bore coating for the inner surfaces of cellular glass, rigid poly‐urethane, urea‐formaldehyde, or poly‐isocyanate foam insulation to reduce abrasion from vibration and temperature changes of piping or vessels. Water None None

Quick setting, water-based, thixotropic adhesive for sizing and adhering canvas, glass cloth and other fabrics to insulation. Water ≤ 2.0 None

A white, fire resistive, tough, washable, abrasion‐resistant indoor coating for thermal insulation. It is also used as a lagging and lap adhesive for canvas and glass lagging cloth.

Water ≤ 1.2 None

A white, tough, washable, abrasion‐resistant indoor coating for use over thermal insulation in areas where high humidity and elevated temperatures are a problem. Water ≤ 1.2 None

Economical asphalt cutback vapor retarder mastic for insulation protection on cold systems. Tough and durable for exterior applications. Also suitable for underground applications.

Solvent ≤ 0.015111℉(44℃)

Asphalt cutback vapor retarder mastic with added fire resistance. For use on exterior applications on cold insulation systems. Solvent ≤ 0.017

199.4℉(93℃)

A tough, flexible, fire‐resistive elastomeric finish for protection of thermal insulation. And for vapour barrier finish for fittings. Excellent for outdoor use where good color retention, chemical resistance, and durability

Solvent ≤ 0.02111℉(44℃)

A tough, flexible, fire resistive finish which provides outstanding chemical and weather resistance. Used on cold and cryogenic insulation systems. Solvent ≤ 0.02

111℉(44℃)

Flexible fire resistive vapor retarder coating for rigid insulation and fittings. Also used to vapour seal ASJ, facing laps and weld pin punctures.

Solvent ≤ 0.05111℉(44℃)

Weatherproof water vapour barrier designed to protect insulation systems applied to equipment operating below ambient temperatures located in most industrial environments. Solvent ≤ 0.02

111℉(44℃)

Heat Resistant Coating is an air drying and heat curing, pigmented silicone resin solution, normally applied to metal to prevent general and specific corrosion problems.

None None 392℉(200℃)

Self‐Adhesive Polymer Membrane product as the primary vapour barrier, which is laminated with a functional film. PET(12㎛)/Aluminum(25㎛)/PET(12㎛)

None 0.00 None

Self‐Adhesive Polymer Membrane product as the primary vapour barrier, which is laminated with a functional film. PET(12㎛)/Aluminum(25㎛)/PET(12㎛). M1 grade(flame retardant materials) / NF P 92‐501.

None 0.00 None

Self‐Adhesive Polymer Membrane product as the primary vapour barrier, which is laminated with a functional film. PET(25㎛) /G.C#10(25㎛). M1 grade(flame retardant materials) / NF P 92‐501

None 0.00 None

Self‐Adhesive Polymer Membrane product which is laminated with a functional film, and protects urethane foam of LNG storage facilities. PET(12㎛)/Aluminum(25㎛)/PET(12㎛). M1 grade(flame retardant materials) / NF P 92‐501 None 0.00 None

Mastics and Coatings

2 See PDS for methods and test conditions.* Chlorosulfonated Polyethylene Rubber(CSM) is also known as Hypalon, a trademark of DuPont Performance Elastomers, and is no longer produced by DuPont.

4 TIC CORPORATION

Product nameand Code Number General Description Type of Volatile Flash Point

Aqueous Elastomeric AdhesiveTIC 5010

High tack, water-based adhesive for attaching low density fibrous insulation and duct liner to painted and unpainted metal. Also may be used for contact applications. None None

PU Adhesive 20TIC 5020

PU Adhesive 20 has strong Adhesion for attachment of Cellular Glass and Polyurethane, Polyisocyanurate that is two elements type of adhesive, which does not contain any flammable materials such as solvent.

None > 392℉(200℃)

PU Adhesive 30 TIC 5022, TIC 5022S

PU Adhesive has strong Adhesion for attachment of Cellular Glass andPolyurethane, Polyisocyanurate that is two elements type of adhesive, which does not contain any flammable materials such as solvent. 20,000~30,000 / 10,000~20,000cps

None > 399.2℉(204℃)

N. T PU Adhesive TIC 5030

Used to bond cryogenic and low temperature insulations to themselves and to metal and masonry substrates. Chemically cures to form a strong yet flexible bond. May be used down to ‐196℃ (‐321℉) with PIR insulation. DNV Type Approval

None > 399.2℉(204℃)

High-Setting PU Adhesive TIC 5050

It has strong Adhesion for attachment of Cellular Glass and Polyurethane,Polyisocyanurate which is two elements type of Adhesive for strong thermosetting of insulation materials and does not contain any flammable materials such as solvents.

None > 392℉(200℃)

PU Adhesive TIC 5060, 5065

A solvent‐free, two‐component adhesive, based on polyurethane. The resin consists of organic compounds with hydroxyl‐groups whereas the hardener is based on isocyanates. DNV Type Approval

None > 399.2℉(204℃)

PU Adhesive TIC 5066

Polyether polyol based two components adhesive. Main material is made of an organic compound containing Hydroxyl‐group. A hardener is made of isocyanates. It has good durability and elasticity.

None > 399.2℉(204℃)

PU Adhesive TIC 5070

Two-component adhesive, based on polyurethane which useable low and high temperature system. Is usable for piping for ducts, compressors, pumps, flanges and valves in the oil/petrochemical field, or other field which require sound proof.

None > 399.2℉(204℃)

PU Adhesive TIC 5075, 5077

Based by bitumen and polyol. It has low vapour permeance and strong resistibility on water. It has high elongation, so that it can used on decreasing vibration and for soundproofing surface. ABS Type Approval

None 199.4℉(93℃)

Fire Resistive AdhesiveTIC 5080

A superior adhesive for cementing thermal insulation to all structural surfaces. It is quick setting, with good specific adhesion to iron, steel, aluminum, and most thermal insulations. It can be used without mechanical fastening for marine hull insulation.

None 111℉(44℃)

Butyl Cryogenic Adhesive/CoatingTIC 6050(2K), 6051(1K)

A 2k or 1k sealant / coating designed for use in cryogenic applications. It is suitable for application to PIR foam, cellular glass and fibrous glass insulations in conjunction with aluminum and steel. Cures to a tough elastomeric film.

None 111℉(44℃)

Cryogenic AdhesiveTIC 6060

A chemically curing,100%solids,three-component epoxy adhesive with a lower service temperature of minus -196℃. None

≥ 302℉(150℃)

Fibrous AdhesiveTIC 6070

Sodium silicate-based adhesive for bonding calcium silicate insulation to itself and to substrates. Water

≥ 392℉(200℃)

Rubber Contact AdhesiveTIC 6080

Non-flammable contact cement with high initial strength.Used for lap sealing and bonding two impermeable surfaces. None None

QS Elastomeric AdhesiveaTIC 6084

Quick setting, rubber-based adhesive for bonding fibrous glass and acoustical duct liner. Solvent < 20℉(-7℃)

Elastomeric AdhesiveTIC 6085

Economical, quick‐setting, synthetic elastomeric insulation adhesive. It has been designed for use in attaching low density duct liner and fibrous glass insulation to sheet metal. TIC 6085 Elastomeric Adhesive meets ASTM C 916, Type IV requirements

Solvent≤ 20℉(-7℃)

Adhesives

LNG Ship Approval Product.

5TIC CORPORATION

Suggested Use1

Attachment LapSealing Lagging

Joint andFitting

Fabrication

DuctLiner

● ○ ●

●

● ●

● ●

● ○

● ●

● ●

● ●

● ●

Insulation Type

Fiberglass and Mineral

Wool

PIR/ Polyurethane

/PhenolicCellular

Glass Polystyrene CalciumSilicate

RubberFoam

● ● ○

● ●

● ●

● ● ●

● ●

● ●

● ●

● ●

● ●

● ○ ○

● ●

● ●

●

○ ○ ●

●

●

Adhesives

6 TIC CORPORATION

Product nameand Code Number General Description

ServiceTemperature Limits at Coated Surfaces

Type of Volatile Flash Point

Joint SealantTIC 7010

Vapor barrier joint sealant that remains flexible and will not shrink or crack. Also used for flashing metal jacketing and bedding of rigid insulations including cellular glass. PIR and polystyrene.

-99.4℉ to 302℉ (-73℃ to 150℃) Solvent

≥ 199.4℉(93℃)

Elastomeric Vapour Barrier SealantTIC 7020

Flexible sealant and elastomeric vapor barrier. Resists ultra-violet, water soak, vibrational stress. Permanently flexible. Used to vapor seal joints of cellular glass and PIR/PUR insulations. Also used as sealant for joints in metal jacketing.

-320.8℉ to 199.4℉ (-196℃ to 93℃) Solvent 199.4℉

(93℃)

Flexible Joint SealingTIC 7030 Elastomeric vapor barrier joint sealant and flashing compound. For insulation,

masonry and metal jacketing. Aluminum pigmented.-99.4℉ to 300℉ (-73℃ to 149℃) Solvent > 212℉

(100℃)

Firestop Silicone SealantTIC 7040, TIC 7040w

A single part, low modulus neutral cure silicone firestop. It has been tested to ASTM E 814 (UL 1479) and meets the criteria for fire/smoke/draft stop for BOCA –CABO – UBC – SBCCI – IRC – IBC, CLASS B2 / DIN 4102/DNV MED Approval

-67℉ to 482℉ (-55℃ to 200℃) None None

RTV Silicone Sealant (Acetic)TIC 7100

A single part, paste typed material.It can be applied overhead or sidewall joints when applying, because it maintains its state and does not flow itself.

-58℉ to 302℉ (-50℃ to 150℃) None > 212℉

(100℃)

High Temperature Silicone SealantTIC 7200

A single part, room temperature harden RTV silicone sealant.It designed to endure high temperature. It has excellent heat-resisting property, cold resistance, durability.

-67℉ to 572℉ (-55℃ to 300℃) None > 212℉

(100℃)

Flexible SealantTIC 8010

A fast setting, elastomeric compound designed as a joint sealant for high velocity air conditioning ducts installed indoors. Mechanical fasteners of the type and number normally used for duct assemblies are required to provide rigidity to the duct system.

-40℉ to 199.4℉ (-40℃ to 93℃) None > 212℉

(100℃)

Vapour Barrier SealantTIC 8020 Fire-resistive, neutral water based, indoor/outdoor vapour barrier sealant for

low, medium and high velocity heating and air conditioning ducts.19.4℉ to 199.4℉

(-7℃ to 93℃) None None

Anti-Fungus SealantTIC 8030

Fire resistive, water based, indoor/outdoor, U.V. resistant sealant for use on low, medium and high velocity ducts to form an extremely flexible, yet durable seal against air leakage. It is supplied in a special thixotropic consistency.

19.4℉ to 199.4℉ (-7℃ to 93℃) None None

REINFORCING MEMBRANES

Glass cloth #10TIC G.C #10 A 10' x 10' glass mesh. Used to reinforce mastic, coatings and sealants.

Master ReinforcingTIC M.A.R A white leno weaves synthetic fiber reinforcing membrane.

Easy to handle yet superior to glass mesh because of its elastic properties.

Mylar FoilTIC Mylar Foil TIC Mylar Foil has excellent resistance to a tear and good resistance to punctures.

TIC Mylar Foil has wide range of temperature application

Mylar Foil TapeTIC Mylar Foil Tape TIC Mylar Foil Tape has excellent resistance to a tear and good resistance to punctures.

TIC Mylar Foil Tape has wide range of temperature application and good adhesion and fire resistance.

Sealants

LNG Ship Approval Product.

7TIC CORPORATION

Product nameand Code Number General Description

ServiceTemperature Limits at Coated Surfaces

Type of Volatile Flash Point

Insulating CementTIC 9010

Water‐based product composed of mineral fibers and other inorganic compounds, which can protect insulation materials from corrosion. Insulating Cement meets ASTM C 449 requirements.

39.2℉ to 1,202℉(4℃ to 650℃) Water None

Insulating CementTIC 9010C

Insulating Cement is water‐based product composed of mineral fibers, perlite, and other inorganic compounds, which can protect insulation materials from corrosion. Insulating Cement meets ASTM C 449 requirements.

39.2℉ to 1202℉(4℃ to 650℃) None None

Hard CementTIC 9010H

Hard Cement is water‐based hard cement, which is composed of compound of mineral fiber, several kinds of inorganic materials protects insulation materials from corrosion.

39.2℉ to 1202℉(4℃ to 650℃) None None

Insulating MortarTIC 9020 Insulation material used as joints, and has low shrinkage and excellent

constructability and adhesion.32℉ to 1,112℉(0℃ to 600℃) None None

Gypsum PlasterTIC 9050

Gypsum Plaster is reactive powder type gypsum, which can be changed as incombustible Adhesive, Bore Coating, HT reinforced Cellular Glass and Inorganic Materials when this product is mixed with water.

-320.8℉ to 932℉(-196℃ to 500℃) None None

Hear Transfer CementTIC 9060 A special paste‐type of cement, which maintains regular temperature of pipeline

when crude oil and high viscosity of oil transfer through pipeline.-148℉ to 1,112℉(-100℃ to 600℃) None None

Hear Transfer CementTIC 9061ct A special paste‐type of cement, which maintains regular temperature of pipeline

when crude oil and high viscosity of oil transfer through pipeline.-320℉ to 700℉

(-196℃ to 371℃) None None

Cements

PU AdhesiveTIC 5022TIC 5030TIC 5065

Metal Sealant(For Steel Jacketing)TIC 7030

Adhesive for Secondary Vapor barrier(Malar Foil)TIC 6080

Vapour StopTIC 6050

Reinforcing MembranesTIC G.C #10TIC M.A.R

Joint SealerTIC 7010TIC 7020

Mastic / Coating / BarrierTIC 1010TIC 2030/2035TIC 3010/3020TIC 4015/4016TIC 4050/4051TIC 4055/4056TIC Bwrap

Insulation Protection

General Notes 1. The recommendations in this selection guide are of general nature only. Refer the product data sheets to be certain that the selected TIC® product meets all the requirements of the application.

2. Do not apply exterior weather barrier coating on horizontal surfaces that might be subject to prolonged ponding of water.

3. If insulation cement is used, it must be completely dry before applying TIC® mastics or coatings. Prime as required.

4. Because of the variation in surface characteristics of facing materials, we recommend that the user conduct their own adhesion test when choosing a coating or mastic for foil, kraft and plastic-faced insulations.

5. The TIC® products listed in this guide are for professional use only

106, 5sandan 2-ro, Seongnam, Dongnam, Cheonan, Chungnam, Republic of KoreaPhone 82-41-558-4252 Fax 82-41-558-9360E-mail sales@tickorea.com www.tickorea.com

ⓒ2018, TIC CORPORATION