SERIES 5570 IMPACT RESISTANT SLIDING GLASS DOOR · 2021. 1. 27. · series 5570 impact resistant sliding glass door including pockets & 90°/135° corners general notes: 1)glazing

INSTRUCTIONS:1) KNOWING THE REQUIRED DESIGN PRESSURE OF THE OPENING, THE ANCHORREQUIREMENTS FOR THE SLIDING GLASS DOORS MAY BE DETERMINED FROM DESIGNPRESSURE TABLES 1 OR 2, DEPENDING ON THE GLASS/REINFORCEMENT.2) LOCATE THE SLIDING GLASS DOOR SIZE ON THE TABLE, USING THE FRAME HEIGHT AND THENOMINAL PANEL WIDTH IF YOUR EXACT SIZE IS NOT LISTED, ROUND UP TO THE NEXT GREATERLISTED WIDTH AND/OR HEIGHT.3) CHOOSE WHICH ANCHOR GROUP (A-D) IS MOST APPLICABLE. ANCHORS ARE DEFINED INTABLE A, THIS SHEET, ALONG WITH THE CORRESPONDING SUBSTRATE, MINIMUM EMBEDMENTAND MINIMUM EDGE DISTANCE.4) FROM THE DESIGN PRESSURE TABLES (TABLES 1 OR 2), VERIFY THAT THE OPENING'SREQUIRED DESIGN PRESSURE IS MET OR EXCEEDED. USE THE ANCHOR QUANTITIES SHOWN.5) INSTALL AS PER THE GUIDELINES OF THIS SHEET-SET.6) ADDITIONALLY, SEE THE EXAMPLE ON SHEET 9.

GENERAL NOTES.............EXAMPLE CONFIGS..........INSTALL DETAILS..............DP/ANCHOR TABLES........EXAMPLE............................GLAZING DETAILS............ANCHOR LOCATIONS.......PANEL TYPES...................EXTRUSIONS.....................ACCESSORIES..................SCREEN DETAILS.............PARTS LIST........................FIN ADDON INSTALL.........

123-67-891011-16171819202122-25

SERIES 5570 IMPACT RESISTANT SLIDING GLASS DOORINCLUDING POCKETS & 90°/135° CORNERS

GENERAL NOTES:1) GLAZING TYPE OPTIONS: SEE GLAZING DETAILS ON SHEET 10.2) DESIGN PRESSURES:A. NEGATIVE DESIGN LOADS BASED ON TESTED PRESSURE AND GLASS PER ASTM E1300.B. POSITIVE DESIGN LOADS BASED ON WATER TEST PRESSURE AND GLASS PER ASTM E1300.3) ANCHORAGE: THE 33-1/3% STRESS INCREASE HAS NOT BEEN USED IN THE DESIGN OF THIS PRODUCT. ANCHORSSHALL BE COATED OR CORROSION RESISTANT AS SPECIFIED IN THE 2006 TEXAS REVISIONS TO THE 2006INTERNATIONAL BUILDING CODE.4) SHUTTERS ARE NOT REQUIRED PER IBC REQUIREMENTS, AS APPLICABLE.5) INSTALLATION SCREWS & FRAME SPLICES TO BE SEALED WITH NARROW JOINT SEALANT.6) REFERENCES (NOA'S): ELCO ULTRACON, CRETEFLEX & AGGREGATOR ANCHOR NOA'S, VISION EXTRUSION, LTD.WHITE RIGID PVC NOA, VE 1000 TAN 202 AND LIGHTER SHADES (NON-WHITE) RIGID PVC NOA AND BROWN COATED(PAINTED OR LAMINATED) WHITE RIGID PVC NOAREFERENCES (TEST REPORTS): FTL-6367, 6368, 6370, 6371, 6376-6380, 8539-8545; EXOVA-10-002-792(A) & 10-006-10231;CAMBRIDGE 535753-09;7) DOOR SIZES MUST BE VERIFIED FOR COMPLIANCE WITH EGRESS REQUIREMENTS OF THE IBC, AS APPLICABLE.8) DRAWINGS DEPICT EXTERIOR-GLAZING, HOWEVER INTERIOR-GLAZING MAY BE SUBSTITUTED.9) THE 5570 SERIES SLIDING GLASS DOOR MAY ALSO BE KNOWN AS THE 570/2770 SERIES.

* MIN. OF 3 THREADSBEYOND THE METALSUBSTRATE.

FOR STEEL STUDS,MIN. FU=45 KSI &MIN. FY=33 KSI.

"UNGROUTED CMU" VALUESMAY BE USED FOR GROUTEDCMU APPLICATIONS.

DESIGN PRESSURE RATINGSEE TABLES 1, 2 & B1, B2

ON SHEETS 7 & 8

IMPACT RATINGRATED FOR LARGE & SMALL

MISSILE IMPACT RESISTANCE

GENERAL NOTES

VINYL SLIDING GLASS DOOR TDI (LM)

NTS 1 OF 25

J ROSOWSKI

3/24/16

Des

c.

Scal

e

Shee

t

DW

G

Serie

sTi

tle

No.

Rev

.

Dra

wn

By

Dat

e

®

1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600

Rev

AR

evB

Dat

eD

ate

Rev

AR

evB

No.SGD-5570

ANCHOR NOTES:1) FOR CONCRETE/CMU SUBSTRATE, SEE TABLE A ON THIS SHEET FOR EMBEDMENT, EDGE DISTANCE ANDSUBSTRATE REQUIREMENTS.2) FOR OTHER SUBSTRATE APPLICATIONS SEE TABLE A ON THIS SHEET.3) WOOD BUCKS DEPICTED AS 1X ARE LESS THAN 1-1/2" THICK. PROPERLY SECURED, 1X WOOD BUCKS ARE OPTIONALIF UNIT IS INSTALLED DIRECTLY TO SOLID CONCRETE OR CMU. WOOD BUCKS DEPICTED AS 2X ARE 1-1/2" THICK ORGREATER. 1X AND 2X BUCKS (WHEN USED) SHALL BE DESIGNED TO PROPERLY TRANSFER LOADS TO THESTRUCTURE. BUCK DESIGN AND INSTALLATION IS THE RESPONSIBILITY OF THE ENGINEER OR ARCHITECT OF RECORD& TO BE REVIEWED BY THE BUILDING OFFICIAL.4) IF SILL IS TIGHT TO SUBSTRATE, GROUT OR OTHER MATERIAL IS NOT REQUIRED. IF USED, NON-SHRINK,NON-METALLIC GROUT, MAX. 1/4" THICK & 3400 PSI MIN., (DONE BY OTHERS) MUST FULLY SUPPORT THE ENTIRELENGTH OF THE SILL THAT IS NOT TIGHT TO THE SUBSTRATE, AND TRANSFER SHEAR LOAD TO SUBSTRATE. IFSUBSTRATE IS WOOD, 30# FELT PAPER OR MASTIC IS REQUIRED BETWEEN THE GROUT AND WOODSUBSTRATE, OR AS APPROVED BY THE AUTHORITY HAVING JURISDICTION.

STANDARDS USED:2006 INTERNATIONAL BUILDING CODE (IBC)ASTM E1300-09ANSI/AF&PA NDS-2012 FOR WOOD CONSTRUCTIONALUMINUM DESIGN MANUAL, ADM-2010AISI-S100-07/S2-2010

TABLE A:

TDI-SGD5570.2 A. LYNN MILLER, P.E. P.E.# 1069547/27/2017

®


X#

DETAIL LETTER

SHEET NUMBER

EXAMPLE CONFIGURATIONS

NTS 2 OF 25

J ROSOWSKI

DLO WIDTH = NOM. PANEL WIDTH - 8-9/16"DLO HEIGHT = DOOR HEIGHT - 11-1/16"PANEL HEIGHT = DOOR HEIGHT - 2-1/2"

G

H5

5

CORNER, TYP.

90°

OR

135

° C

OR

NE

R

SEENOTE2, THISSHEET.

E4

F4

MAX. UNIT WIDTHNOM. PANEL WIDTH

PER TABLES 1 & 2

MAX. UNITHEIGHT

PERTABLES 1 & 2

A

F

B3

4

3

1-PANELCONFIGURATIONS

MAX. UNITHEIGHT

PER TABLES 1 & 2

SE

E N

OTE

3 B

ELO

W

E4

I6

A3

E4

F4

C3

A3

E4

F4

D

I3

6

D

I3

6

MAX. UNIT WIDTHMAX. UNIT WIDTHMAX. UNIT WIDTH

NOM. PANEL WIDTHPER TABLES 1 & 2

POCKET POCKET POCKET



MAX. UNITHEIGHT

PER TABLES 1 & 2

MAX. UNITHEIGHT

PER TABLES 1 & 2

2-PANELCONFIGURATIONS

3-PANEL CONFIGURATIONS

A3

E4

F4

D

I3

6

MAX. UNIT WIDTH

POCKET


MAX. UNITHEIGHT

PERTABLES 1 & 2


A3

E4

F4

D3

MAX. UNIT WIDTH

POCKET


MAX. UNITHEIGHT

PER TABLES 1 & 2


E4

E4

F4

F4

A3

A3

D

I3

6

D3

MAX. UNIT WIDTH

POCKET

POCKET



MAX. UNITHEIGHT

PER TABLES 1 & 2



MAX. UNIT WIDTH

E4

F4

A3

D3

MAX. UNIT WIDTH

POCKET


MAX. UNITHEIGHT

PER TABLES 1 & 2


CONFIGURATIONS NOTES:

1) ALL CONFIGURATIONS SHOWN ARE ALSO AVAILABLE AS POCKET CONFIGURATIONS AT EITHER OR BOTH JAMBLOCATIONS. EXAMPLE: 4-PANEL XXXX IN POCKET (p) CONFIGURATION CAN BE pXXXXp, pXXXX OR XXXXp. OXXX INPOCKET CONFIGURATION CAN BE OXXXp.

2) 90° & 135° CORNER CONFIGURATIONS ARE A COMBINATION OF ANY 2 STRAIGHT CONFIGURATIONS.

3) POCKET WALL OR CAVITY IS NOT PART OF THIS APPROVAL AND IS TO BE DESIGNED BY OTHERS ANDREVIEWED BY THE AUTHORITY HAVING JURISDICTION.

4) FOR NOM. PANEL WIDTH, SEE TABLES 1 & 2.

I6

I6

I6

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

B3C3

OUTSIDE CORNER SHOWN, INSIDE CORNER SIMILAR

MAX. UNITHEIGHT

PER TABLES 1 & 2

"X" = OPERABLE PANEL"O" = INOPERABLE PANEL"p" = POCKET

SE

E N

OTE

3 B

ELO

W

SE

E N

OTE

3 B

ELO

W

SE

E N

OTE

3 B

ELO

W

SE

E N

OTE

3 B

ELO

W

SE

E N

OTE

3 B

ELO

W

SE

E N

OTE

3 B

ELO

W

SE

E N

OTE

3 B

ELO

W

SGD-5570

3/24/16VINYL SLIDING GLASS DOOR TDI (LM)

TDI-SGD5570.2A. LYNN MILLER, P.E.

P.E.# 1069547/27/2017

FORINTERLOCKS

ONLY

FOR ALL LOCKSTILES,ASTRAGALS, FIXED

STILES ANDHORIZONTAL RAILS

NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEET 13 FOR ANCHOR LOCATION & SPACING, FORANCHOR QUANTITIES, SEE TABLES 1 & 2.4) CONTINUOUS ANCHOR PLATE, ITEM #8, IS REQUIRED AT ALLFRAME ANCHOR LOCATIONS.5) PANEL WIDTH DOES NOT INCLUDE INTERLOCK OR ASTRAGAL ADD-ON.6) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS. ALLREINFORCEMENTS ARE APPROXIMATELY THE FULL LENGTH OFTHE EXTRUSION. REFER TO TEST REPORTS FOR EXACT DIMENSIONS.7) SEE SHEET 20 FOR SCREEN DETAILS.

REINFORCEMENT TYPES (SEE NOTE 6, THIS SHEET)

®

1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600 NTS 3 OF 25

J ROSOWSKIINSTALLATION, HORIZONTAL X-SECT.

1/4" MAX.

EDGEDISTANCE

EMBEDMENT

EXTERIOR

DAYLIGHTOPENING

WIDTH

94

25

82

33

50

10

1X OR 2X WOODBUCKSTRIP, SEENOTE 4, SHEET 1

25

27 28

26

25 26OR25 26OR

71

STANDARD HD

32

80

DETAIL A2INTO 2X WOOD

HORIZONTAL SECTION (XXX SHOWN)

DETAIL B2ASTRAGAL

ASTRAGAL MAY BEINSTALLED IN EITHERINTERIOR OREXTERIOR DIRECTION.ALL PARTS IDENTICAL.

FACING INT.

DETAIL C2INTERLOCK

DETAIL D2INTO MASONRY

1/4" MAX.

8

96

2291

21

19

31

CONCRETE/CMU PERANCHOR REQUIREMENT

TYP. ANCHOR TYPE,EMBEDMENT AND

EDGE DISTANCE PERSUBSTRATE, SEE

TABLE A, SHEET 1 &NOTE 3, BELOW

EMBEDMENT

EDGEDISTANCE

EDGEDISTANCE




94

DETAIL A1THRU 1X WOOD

FRAME WIDTH

DETAIL B1ASTRAGAL DETAIL C1

INTERLOCKDETAIL D1

INTO METALFACING EXT.INTO MASONRY

27 28OR

29 #8 X 3/4" SMS REINFORCEMENT SCREW; 7PER STILE, LOCATED AT CENTERLINE AND 6",9" & 12" FROM ENDS (FACTORY INSTALLED).

1/4" MAX.

1/4" MAX.

EDGEDISTANCE

EMBEDMENT

EDGEDISTANCE

EMBEDMENT

PANEL WIDTH




2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHOR

NOTE 3, SHEET 1

8

96 DAYLIGHTOPENING

WIDTH

REQUIRED IF DOORHEIGHT IS OVER 96"

2291

21

71

2393

19

63

2526 OR2728 OR

31

HORIZONTAL SECTION (XO SHOWN)

TYP. ANCHOR TYPE,EMBEDMENT ANDEDGE DISTANCEPER SUBSTRATE,SEE TABLE A, SHEET1 & NOTE 3, BELOW


27

REQUIRED IF DOORHEIGHT IS OVER 96"

FIXED PANEL CLIP &ANCHORS, SEEDETAIL SHEET 19

EXTERIOR

INTERIOR

28OR

SEE NOTE 6, THIS SHEET

SEE NOTE 6,THIS SHEET SEE NOTE 6,

THIS SHEET

SEE NOTE 6,THIS SHEET

SEE NOTE 6, THIS SHEET

INTERIOR

SGD-5570

MAX 28" O.C.

8

8

8

8

ANCHORPLATE AT

EVERYANCHOR

LOCATION

8

METAL TYP., ANCHOR LENGTHTO BE A MIN. OF 3 THREADSBEYOND THE METALSUBSTRATE

TDI-SGD5570.2


A. LYNN MILLER, P.E. P.E.# 1069547/27/2017

1X OR 2X WOODBUCKSTRIP, SEEANCHOR NOTE 3,SHEET 1

EXTERIOR

DAYLIGHTOPENINGHEIGHT

DETAIL E1

.060 .060 .060

2.887 3.4644.041

DETAIL E3

FORLOCKSTILES,ASTRAGALS,FIXED STILES

ANDHORIZONTAL

RAILS

1.793

INTO MASONRY1X BUCKSTRIP

INTO MASONRY

EDGEDISTANCE

EMBED-MENT

EDGEDISTANCE

EMBEDMENT

SEENOTE 6,

THIS SHEET

®


INSTALLATION, VERTICAL X-SECT.

NTS 4 OF 25

J ROSOWSKI

.060

1.917.823

SILL RISER SILL RISER SILL RISER SILL RISER

#42 SHOWN#43-45 ALSO APPLY

2.3702.947

SILL RISERVARIES WITH

REQUIREDPOSITIVEDESIGN

PRESSURE,SEE SHEETS

7 & 8.

CONCRETE/CMUPER ANCHOR

REQUIREMENT

2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHORNOTE 3, SHEET 1

EDGE DISTANCE

MULLION, ALUMINUM/STEELFRAMING OR STEEL STUD. MAYBE VERTICAL OR HORIZONTAL.SEE SUBSTRATE PROPERTIES,TABLE A, SHEET 1

EMBEDMENT

DETAIL E4INTO METAL

DETAIL E2INTO WOOD

1/4" MAX.1/4" MAX.

EDGEDISTANCE

EMBED-MENT

CONCRETE/CMUPER ANCHORREQUIREMENT

1/4" MAX.GROUT AS

NEEDED, SEEANCHOR NOTE

5, SHEET 1

DETAIL F1INTO MASONRY

EMBEDMENT

2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHOR

NOTE 3, SHEET 1

DETAIL F2INTO WOOD

1/4" MAX.1/4" MAX.

1/4" MAX.

1/4" MAX.

EMBEDMENT

EDGEDISTANCE

FRAMEHEIGHT

PANELHEIGHT

EXTERIOR

50

7

33

50

9

33

25

61 62

26

2

8

1

13

42 43 44 45

42

26

25

8

2-1/2" = TOTALSILL HEIGHT

.390.390

.390

.390


12

OR

OR

82

80

63

EDGEDISTANCE


TYP. ANCHOR TYPE,EMBEDMENT ANDEDGE DISTANCEPER SUBSTRATE,SEE TABLE A,SHEET 1 & NOTE 3,THIS SHEET

TYP. ANCHOR TYPE,EMBEDMENT ANDEDGE DISTANCEPER SUBSTRATE,SEE TABLE A,SHEET 1 & NOTE 3,THIS SHEET

(2-1/2" TOTALSILL HEIGHT)




TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A, SHEET1 & NOTE 3, THIS SHEET TYP. ANCHOR TYPE, EMBEDMENT

AND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A, SHEET1 & NOTE 3, THIS SHEET

TYP. ANCHOR TYPE, EMBEDMENT ANDEDGE DISTANCE PER SUBSTRATE, SEETABLE A, SHEET 1 & NOTE 3, THIS SHEET

TYP. ANCHOR TYPE, EMBEDMENT ANDEDGE DISTANCE PER SUBSTRATE, SEETABLE A, SHEET 1 & NOTE 3, THIS SHEET

NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEETS 11 & 12 FOR ANCHOR LOCATION & SPACING,FOR ANCHOR QUANTITIES, SEE TABLES 1 & 2.4) CONTINUOUS ANCHOR PLATE, ITEM #8, IS REQUIRED ATALL FRAME ANCHOR LOCATIONS.5) SEE SHEET 20 FOR SCREEN DETAILS.6) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.ALL REINFORCEMENTS ARE APPROXIMATELY THE FULLLENGTH OF THE EXTRUSION. REFER TO TEST REPORTS FOREXACT DIMENSIONS.

SGD-5570

8

8 88

8

8

#8 X 3/4" SMS REINFORCEMENTSCREW; 3 PER RAIL, LOCATED ATCENTERLINE AND 9" FROM ENDS(FACTORY INSTALLED)

#8 X 3/4" SMS REINFORCEMENTSCREW; 3 PER RAIL, LOCATED ATCENTERLINE AND 9" FROM ENDS(FACTORY INSTALLED)

ANCHOR PLATE ATEVERY ANCHOR

LOCATION

8

TDI-SGD5570.2



DETAIL G1135°

INSIDE CORNER

DETAIL H190°

INSIDE CORNER

DETAIL H290°

OUTSIDE CORNER

DETAIL G2135°

OUTSIDE CORNER

EXTERIOR

EXTERIOREXTERIOR

EXTERIOR

EXTERIOR

EXTERIOR

EXTERIOR

INTERIOR

INTERIOR

INTERIOR

INTERIOR

INTERIOR

INTERIOR

135°

135°90°

90°

®


NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) SEE SHEETS 14 & 15 FOR ANCHOR LOCATION & SPACING, FOR ANCHORQUANTITIES, SEE TABLES 1 & 2.3) CORNER ASTRAGAL MAY BE EITHER TO THE INTERIOR OR EXTERIOR,DEPENDING ON CONFIGURATION.

CORNER ASTRAGAL HORIZ. X-SECT.

NTS 5 OF 25

J ROSOWSKI

237 96

3619

69

26

96

96

69

9635

38

19

19

69

96

40

39

94

41

69

40

39

94

41

33

33

37

33

33

INTERIOR

INTERIOR

INTERIOR

1

1

2

2

1

2

1

OR25

26OR25

26OR25

26OR25

7171

35

SGD-5570

MAX 18.5" O.C.

MAX 18.5" O.C.

MAX 18.5" O.C.

MAX 18.5" O.C.

MAX 18.5" O.C.

MAX 18.5" O.C.

EXTERIOR

9619

MAX 3.5" O.C.SEE SHEET 19




TDI-SGD5570.2



INTERIOR POCKETS MUSTINCLUDE A NON-STRUCTURAL,FRAME JAMB TO REDUCE THE

POSSIBILITY OF WATERINFILTRATION.

OPTIONAL NON-STRUCTURAL

ANCHORS FORINTERIOR POCKET

JAMB

INTERIOR POCKET


TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER

SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW

®


J ROSOWSKIP-HOOK EXAMPLES, HORIZ. X-SECT.

EMBEDMENT

EDGEDISTANCE

METAL TYP., ANCHOR LENGTHTO BE A MIN. OF 3 THREADS

BEYOND THE METAL SUBSTRATE

1/4"MAX.

EDGEDISTANCE


TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PER

SUBSTRATE, SEE TABLE A, SHEET 1& NOTE 3, BELOW

TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A,SHEET 1 & NOTE 3, BELOW

EMBEDMENT

1/4" MAX.

EXTERIOR POCKET

EXTERIOR POCKETEXTERIOR POCKET

DETAIL I2INTO MASONRY

DETAIL I3INTO METAL

1/4" MAX.

EXTERIOR

POCKET BY OTHERS, SEENOTE 6 BELOW.

EDGEDISTANCE

EMBED-MENT

DETAIL I1INTO MASONRY

EXTERIOR

INTERIOR

OPT.ANCHOR

33

30

21

18 OPT.17

10

SEE FIG 1,THIS SHEET

2728 OR

OPT. ANCHOR

EDGEDISTANCE

EMBEDMENT

2X WOOD BUCKSTRIP ORFRAMING, SEE ANCHORNOTE 3, SHEET 1

EXTERIOR

DETAIL I4INTO WOOD

17

82

31

2728 OR

26

31

2728 OR

1/4" MAX.

EXTERIOR

EXTERIOR

FOR DOOR HEIGHTS OVER 96"

FOR DOOR HEIGHTS 96" AND LESS:

30

10

31

OPT. ANCHOR

OPT.ANCHOR

17

17

30

10

FIGURE 1, INTERLOCKS AT POCKETS:

NTS 6 OF 25

9121

2221 91

2221

91

97 21.9"MAX. O.C.

OPT.

OPT. OPT.




SGD-5570

NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) REFER TO ANCHOR NOTES, SHEET 1.3) SEE SHEET 13 FOR ANCHOR LOCATION & SPACING, FOR ANCHOR QUANTITIES, SEE TABLES 1 & 2.4) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.5) INTERIOR OR EXTERIOR POCKETS APPLICABLE FOR ALL INSTALLATION METHODS.6) POCKET WALL OR CAVITY IS NOT PART OF THIS APPROVAL AND IS TO BE DESIGNED BY OTHERSAND REVIEWED BY THE AUTHORITY HAVING JURISDICTION.

22

TDI-SGD5570.2



TABLE B1:

DP & ANCHOR QUANTITY TABLE

NTS 7 OF 25

J ROSOWSKI

Des

c.

Scal

e

Shee

t

DW

G

Serie

sTi

tle

No.

Rev

.

Dra

wn

By

Dat

e

®


Rev

AR

evB

Dat

eD

ate

Rev

AR

evB

No.

TABLE 1:

TABLE NOTES:

1) SEE SILL RISER TYPES ON SHEET 4.2) SHEET APPLIES TO 2, 3 AND 4 TRACK CONFIGURATIONS.3) REFER TO ANCHOR NOTES, SHEET 1.4) SEE SHEETS 11-16 FOR ANCHOR LOCATION & SPACING


TOTAL # OF ANCHORS THROUGH THE JAMB.

THE MAXIMUM DP AT THESE ANCHOR QUANTITIES.

ANCHORAGE TYPE PER SUBSTRATE REQUIRED TO ACHIEVE THE DESIGNPRESSURE, USING THE ANCHOR QUANTIES LISTED BELOW. SEE TABLE A,SHEET 1 FOR COMPLETE ANCHOR LIMITATIONS.

THE # OF ANCHORS REQUIRED THROUGH THE P-HOOK,PERPENDICULAR TO THE GLASS.

USED IN EXAMPLE ON SHEET 9

# OF ANCHORS THROUGH THE HEAD & SILL. (EX: FOR C3+1, 3 ANCHORSCLUSTERED AT PANEL MEETING POINT AND 1 ANCHOR REQUIRED ATMIDSPAN OF PANEL).

SGD-5570 TDI-SGD5570.2




TOTAL # OF ANCHORS THROUGH THE JAMB.

THE MAXIMUM DP AT THESE ANCHOR QUANTITIES.

ANCHORAGE TYPE PER SUBSTRATE REQUIRED TO ACHIEVE THE DESIGNPRESSURE, USING THE ANCHOR QUANTIES LISTED BELOW. SEE TABLE A,SHEET 1 FOR COMPLETE ANCHOR LIMITATIONS.

DP & ANCHOR QUANTITY TABLE

NTS 8 OF 25

J ROSOWSKI

Des

c.

Scal

e

Shee

t

DW

G

Serie

sTi

tle

No.

Rev

.

Dra

wn

By

Dat

e

®


Rev

AR

evB

Dat

eD

ate

Rev

AR

evB

No.

TABLE 2:

* +/-100.0 PSF FOR ANCHOR GROUPS B, C & D.

TABLE NOTES:

1) SEE SILL RISER TYPES ON SHEET 4.2) SHEET APPLIES TO 2, 3 AND 4 TRACK CONFIGURATIONS.3) REFER TO ANCHOR NOTES, SHEET 1.4) SEE SHEETS 11-16 FOR ANCHOR LOCATION & SPACING

TABLE B2:

# OF ANCHORS THROUGH THE HEAD & SILL. (EX: FOR C3+1, 3 ANCHORSCLUSTERED AT PANEL MEETING POINT AND 1 ANCHOR REQUIRED ATMIDSPAN OF PANEL).

THE # OF ANCHORS REQUIRED THROUGH THE P-HOOK,PERPENDICULAR TO THE GLASS.




HEAD SPLICE

CENTERLINEOF PANEL 2

CENTERLINEOF INTERLOCK




"+2" ANCHORAGE,SHEET 12 "+2" ANCHORAGE,

SHEET 12"C3" CLUSTER,SHEET 12

"C3" CLUSTER,SHEET 12 END ANCHORAGE

(MIN. 1 ANCHOR)

3-PANEL, 3 TRACK, STRAIGHT CONFIGURATION - PXXX,INTERIOR MOUNT POCKET, 48" X 84" NOM. PANELS,LAMINATED, IG GLAZING, ANCHOR GROUP A IN WOOD SUBSTRATE,PROJECT DESIGN PRESSURE REQUIRED: +48.2/-58.6 PSF

JAMBANCHORAGE

DETAILS

EXTERIOR

6" MAX.

21.6"MAX.O.C.

P-HOOKANCHORAGE

DETAILS

"+2"ANCHORAGE,

SHEET 12

SEE POCKET JAMBINSTALLATION ONSHEET 6

FRAME JAMB REQUIRED@ INTERIOR POCKETS

HEAD ANCHORAGE DETAILS

1) KNOWING THE PRODUCT'S REQUIREMENTS, SCAN THROUGH TABLES 1 & 2FOR A DESIGN PRESSURE THAT MEETS OR EXCEEDS THE REQUIREMENT OF+48.2/-58.6 AT A NOM. PANEL SIZE OF 48" X 84". FROM TABLE 1, SHEET 7, THEDESIGN PRESSURE IS +60/-60 WHICH EXCEEDS THE PROJECT DESIGNPRESSURE REQUIREMENTS.

FOR WOOD INSTALLATION USING ANYANCHOR IN GROUP A (SEE TABLE A), TABLE1 SHOWS ANCHOR REQUIREMENTS OF:

2) ANCHOR LOCATION DETAILS, CAN BE FOUND ON:HEAD (CLUSTER ANCHORS): SHEET 12 FOR THE "C3" CLUSTER ANCHORS ATTHE INTERLOCK/ASTRAGAL.HEAD (INTERMEDIATE ANCHORS): SHEET 12 FOR THE "+2 ANCHORS AT THEMIDSPAN OF EACH PANEL.SILL (CLUSTER ANCHORS): SHEET 11 FOR THE "C3" CLUSTER ANCHORS ATTHE INTERLOCK/ASTRAGAL.SILL (INTERMEDIATE ANCHORS): SHEET 11 FOR THE "+2 ANCHORS AT THEMIDSPAN OF EACH PANEL.JAMB: 5 ANCHORS, SHEET 13 FOR GEN. LAYOUT.P-HOOK: 7 ANCHORS, SHEET 13 FOR GENERALLAYOUT.

3) INSTALLATION DETAILS INTO WOOD CANBE FOUND ON:HEAD & SILL: SHEET 4JAMB: SHEET 3P-HOOK: SHEET 6

STRAIGHT DOOR EXAMPLE

NTS 9 OF 25

J ROSOWSKI

®


6"MAX.

6"MAX.

SEE FIGURE BELOW FOR ADDITIONALANCHOR INFORMATION.

25-3/8" MAX.

EXTERIOR

INTERIOR

FOR SILL (SHOWN) AND HEAD, ANCHORS AT THEMIDPOINT OF END PANELS ARE ONLY REQUIRED IF THEO.C. DISTANCE TO THE NEXT ANCHOR CLUSTER IS OVER25-3/8", OTHERWISE ANCHORS ARE NOT REQUIRED ASPER THE FIGURE ABOVE:

DISTANCE TO NEXT CLUSTERTO BE 25-3/8" O.C. OR LESS

CENTERLINE OF END PANEL

SILL SPLICE






"+2" ANCHORAGE,SHEET 11 "+2" ANCHORAGE,

SHEET 11"C3" CLUSTER,SHEET 11

"C3" CLUSTER,SHEET 11 END ANCHORAGE

(MIN. 1 ANCHOR)

"+2"ANCHORAGE,

SHEET 11

SEE POCKET JAMBINSTALLATION ONSHEET 6

FRAME JAMBREQUIRED @INTERIOR POCKETS

SILL ANCHORAGE DETAILS

6"MAX.

6"MAX.

SEE FIGURE BELOW FOR ADDITIONALANCHOR INFORMATION.

25-3/8" MAX.

EXTERIOR

INTERIOR

FOR PRODUCT REFERENCES, ALSO SEE:A) SHEET 2 FOR ALLOWABLE CONFIGURATIONS AND EXACTLOCATIONS OF CROSS-SECTION DRAWINGS.B) SHEET 10 FOR SPECIFIC GLAZING TYPES.C) SHEET 17 FOR ALLOWABLE PANEL TYPES AND CALL NAMES.D) SHEETS 4 & 18 FOR EXTRUSION CROSS-SECTION DRAWINGS.E) SHEET 19 FOR INSTALLATION OF ADDITIONAL ACCESSORIES.F) SHEET 21 FOR A BILL OF MATERIALS.

12" MAX.

6" MAX.

6" MAX.

OPT. ANCHORTO AID IN

ALIGNMENT


ALIGNMENT

EXAMPLE:

SPLICE NOTE:NON-STRUCTURAL ANCHORS MAYBE ADDED IN-FIELD AS NEEDED TO

ALIGN THE HEAD OR SILL IF ASPLICE OCCURS WITHIN A POCKET.

PXXX (3-TRACK)

PXXX (3-TRACK)

END PANEL ANCHOR EXCEPTION:

SGD-5570

POCKET BYOTHERS, SEE

NOTE 6,SHEET 6

POCKET BYOTHERS, SEE

NOTE 6,SHEET 6

EXTERIOR INTERIOR

TDI-SGD5570.2



NOTES:1) BACKBEDDING SURFACES SHALL NOTBE PAINTED OR LAMINATED.2) PRODUCT MAY BE EITHER INTERIOR OREXTERIOR GLAZED, PROVIDED THAT THE"HS" SURFACE OF A LAMINATED GLAZINGUNIT IS ADHERED TO THE GLAZING LEG.

"ANN" = ANNEALED"HS" = HEAT STRENGTHENED"T" = TEMPERED"PVB" = .090" BUTACITE® PVB INTERLAYERBY KURARAY AMERICA, INC."SG" = .090" SENTRYGLAS® INTERLAYERBY KURARAY AMERICA, INC.

GLAZING DETAILS

NTS

J ROSOWSKI

®

1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600 10 OF 25

3/16" ANN GLASS.090" PVB

3/16" HS GLASS

7/16" NOM.

3/16" HS GLASS.090" SG

3/16" HS GLASS

3/16" T GLASS7/16" AIR SPACE

1-1/16" NOM.

3/16" HS GLASS

.090" PVB

3/16" ANN GLASS


1-3/16" NOM.

GLASS TYPE 1

3/16" HS GLASS.090" SG

3/16" HS GLASS

7/16" NOM.

GLASS TYPE 2

GLASS TYPE 4

3/16" ANN GLASS.090" PVB

3/16" HS GLASS


1-1/16" NOM.

GLASS TYPE 3

HEAT-MIRROR FILM9/32" AIR SPACE

GLASS TYPE 5

7/8" NOM.GLASSBITE

86

79

7/8" NOM.GLASSBITE

86

79

7/8" NOM.GLASSBITE

86

79

7/8" NOM.GLASSBITE

7/8" NOM.GLASSBITE

85

79

PAINTED/LAMINATEDSURFACE





85

79

83OR82

XL EDGESPACER

DURASEALSPACER

SUPERSPACER NXT

7877

76

EXT. GLASS

BUTYL &DESICCANT

FOAM

STRUCTURALSILICONE

FOAMWITH

DESICCANT

ROLL-FORMEDSTAINLESS STEEL

INT. GLASS

ALUMINUMREINFORCEMENT POLYISO-

BUTYLENESEAL

SILICONE SEAL

EXT. GLASS

INT. GLASS

EXT. GLASS

INT. GLASS

DESICCANT FILL AREA

R TM

HOT-MELT BUTYL

R TM

5/16" NOM.

3/16" NOM.

5/16" NOM.

KODISPACE4SG TPS

75

STRUCTURALPOLYISOBUTYLENWITH DESICCANT

EXT. GLASS

INT. GLASS

SILICONE

1/4" NOM.

7877

7675

SGD-5570

7877

7675

77


PRODUCT IS "EXTERIOR-GLAZED" IF #80-81 ISTOWARDS THE EXTERIOR.

EXTERIOR

PRODUCT IS "INTERIOR-GLAZED" IF #80-81 ISTOWARDS THE INTERIOR.

INTERIOR



EXTERIOR


INTERIOR



EXTERIOR


INTERIOR



EXTERIOR


INTERIOR

84


PRODUCT IS "EXTERIOR-GLAZED" IF #84 ISTOWARDS THE EXTERIOR.

EXTERIOR

PRODUCT IS "INTERIOR-GLAZED" IF #84 ISTOWARDS THE INTERIOR.

INTERIOR

83OR8281OR80 81OR80

TDI-SGD5570.2



2-TRACK INTERMEDIATE"+1" ANCHOR LOCATION

EXTERIOR EXTERIOR EXTERIOR

EXTERIOREXTERIOREXTERIOR

EXTERIOR EXTERIOR

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

2-TRACK INTERMEDIATE"+2" ANCHOR LOCATIONS






SILL "+" INTERMEDIATE ANCHORS LAYOUT:


4" 4"

3.22"

4"

3.22"

4"

EXTERIOR

PANELCENTERLINE


3.22"

4"

EXTERIOR

EXTERIOR

2-TRACK CLUSTER "C3"ANCHOR LOCATIONS


SILL CLUSTER ANCHORS LAYOUT:

FIGURES PERTAIN TO THE FOLLOWING SILLCLUSTER ANCHOR LOCATIONS:

4"

3.22"

4"

EXTERIOR

4-TRACK CLUSTER"C3" ANCHOR LOCATIONS

3.22"

4"

EXTERIOR

EXTERIOR



4"

3.22"

4"

EXTERIOR

4-TRACK CLUSTER"C5" ANCHOR LOCATIONS

3.22"

4"

ASTRAGAL ORINTERLOCK

CENTERLINE


CENTERLINE


CENTERLINE


CENTERLINE


CENTERLINE


CENTERLINE

®


ANCHOR LOCATIONS A

NTS

J ROSOWSKI

11 OF 25

FIGURES PERTAIN TO THE FOLLOWING SILLINTERMEDIATE ANCHOR LOCATIONS:NOTES:

1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.

2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL SILLS:

2.375"

NOTES:1) ALL DIMENSIONS SHOWN ARE BASED ON MINIMUM ALLOWED.

2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL SILLS:

2.375"






PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE



HEAD "+" INTERMEDIATE ANCHORS LAYOUT:

3.22"

3.22"

4"

4"

3.22"

4"

4.75"

EXTERIOR

EXTERIOR



HEAD CLUSTER ANCHORS LAYOUT:

3.22"

3.22"

4"

4"

EXTERIOR

EXTERIOR



3.22"

3.22"

4"

4"






CENTERLINE


CENTERLINE


CENTERLINE


CENTERLINE

®


ANCHOR LOCATIONS B

NTS

J ROSOWSKI

12 OF 25

FIGURES PERTAIN TO THE FOLLOWING HEADCLUSTER ANCHOR LOCATIONS:

FIGURES PERTAIN TO THE FOLLOWING HEADINTERMEDIATE ANCHOR LOCATIONS:


2) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL HEADS:

2.375"



2.375"

SGD-5570

EXTERIOR EXTERIOR

PANELCENTERLINE

PANELCENTERLINE


4-TRACK INTERMEDIATE "+2"ANCHOR LOCATIONS

EXTERIOR

PANELCENTERLINE


3.22"

4"

EXTERIOR

4-TRACK CLUSTER"C3"ANCHOR LOCATIONS

3.22"

4"

EXTERIOR


3.22"

4"ASTRAGAL OR

INTERLOCKCENTERLINE


CENTERLINE

TDI-SGD5570.2



PO

CK

ET

PO

CK

ET

P-HOOK ANCHORS LAYOUT:

NOTES:1) SEE TABLES 1 & 2 FOR EXACT QUANTITYOF ANCHORS REQUIRED IN THE P-HOOK.

2-TRACK FRAMEJAMB ANCHORS

JAMB ANCHORS LAYOUT, (PARTIAL VIEW):

EXTERIOR

6"MAX.

EXTERIOR EXTERIOR

21.6"MAX.O.C.

6"MAX.

21.6"MAX.O.C.

6"MAX.

21.6"MAX.O.C.

®


(4) WEEP NOTCHESPER END @ 1" X .500"

(6) TRACK WEEP HOLESEVERY 24" @ 1.125" X .190";

(1) WEEP NOTCH EVERY24" @ 1.375" X .500"





JAMB

SILL

JAMB JAMB

SILLSILL

SILL WEEPHOLE LAYOUT (2, 3 & 4 TRACKS)

12"MAX.

6" MAX.

6"MAX.


ALIGNMENT


ALIGNMENT



EXTERIOREXTERIOR

EXTERIOR

ANCHOR LOCATIONS C

NTS

J ROSOWSKI

13 OF 25

FIGURES PERTAIN TO THE FOLLOWING POCKET JAMB(P-HOOK) ANCHOR LOCATIONS:

FIGURES PERTAIN TO THE FOLLOWING JAMB ANCHOR LOCATIONS:



NOTES:1) STANDARD ANCHOR LOCATIONS SHOWN.FOR 3 AND 4-TRACK JAMBS, ANCHORS MAYBE LOCATED IN ADJACENT TRACKS(SIMILAR TO THE 2-TRACK JAMB) ASREQUIRED TO MEET MIN. EDGE DISTANCECONSTRAINTS.

2.375" 4.75" 7.125"




2-TRACK 90° CORNER"C4" ANCHOR LOCATIONS

(USE WHERE "C3" IS SPECIFIED)

HEAD 90° CORNER CLUSTER ANCHORS LAYOUT:

®


SILL 90° CORNER CLUSTER ANCHORS LAYOUT:

EXTERIOR EXTERIOR

EXTERIOR EXTERIOR

EXTERIOR

EXTERIOR EXTERIOR

EXTERIOR EXTERIOR

EXTERIOR EXTERIOR

90°

90° ANCHOR LOCATIONS D

NTS

J ROSOWSKI

14 OF 25

4"4"

3.22"

4" 4"

3.22"

4"

4" 4" 4" 4"

4"

4"

4"

4"

3.22"3.22"

4"

4"

4"4"

3.22"

4"

4"









4"













4"

4"

3.22"


2) DETAILS DEPICT ANCHOR QUANTITY AND SPACING, AND WOULD BESIMILAR FOR OUTSIDE (SHOWN) AND INSIDE CORNER CONFIGURATIONS.

3) TRACK-TO-TRACKDISTANCE IS 2.375"FOR ALL HEADS AND SILLS:

2.375" 2.375"

FIGURES PERTAIN TO THEFOLLOWING 90° CORNER SILL

ANCHOR LOCATIONS:

FIGURES PERTAIN TO THE FOLLOWING 90° CORNERHEAD ANCHOR LOCATIONS:

SGD-5570

EXTERIOR4-TRACK 90° CORNER"C6" ANCHOR LOCATIONS


4"

3.22"

4"

TDI-SGD5570.2



HEAD 135° CORNER CLUSTER ANCHORS LAYOUT:

®


SILL 135° CORNER CLUSTER ANCHORS LAYOUT:

EXTERIOR EXTERIOR

EXTERIOR EXTERIOR

EXTERIOR EXTERIOR

EXTERIOR EXTERIOR

EXTERIOR EXTERIOR

EXTERIOR EXTERIOR




135°

135° ANCHOR LOCATIONS E

NTS

J ROSOWSKI

15 OF 25

4"

4"

4"

4" 4"

4"

4"

4"

4"

3.22"

4"

4"

4"

4"

4"

4"

3.22"

4"

4"

3.22"

4"2-TRACK 135° CORNER

"C4" ANCHOR LOCATIONS(USE WHERE "C3" IS SPECIFIED)























3.22"

4"

4"

2.375" 2.375"

FIGURES PERTAIN TO THEFOLLOWING 135° CORNER SILL

ANCHOR LOCATIONS:





EXTERIOR EXTERIOR

EXTERIOREXTERIOR

EXTERIOR

SPLICELOCATION

SPLICELOCATION

SPLICELOCATION

SPLICELOCATION

SPLICELOCATION

SILL SPLICE ANCHORS LAYOUT @ INTERLOCK OR ASTRAGAL:

4"

4"

4"

3.22"

4"

EXTERIOR

SPLICELOCATION

3.22" 3.22"

4"

4"

EXTERIOR EXTERIOR

EXTERIOR

SPLICELOCATION

SPLICELOCATION

SPLICELOCATION

SPLICELOCATION

3.22"

3.22"

4"

4"

3.22"

4"

4.75"

2-TRACK SPLICE"C4" ANCHOR LOCATIONS


4"

HEAD SPLICE ANCHORS LAYOUT @ INTERLOCK OR ASTRAGAL: FIGURES PERTAIN TO THE FOLLOWINGSPLICED SILL ANCHOR LOCATIONS:

FIGURES PERTAIN TO THE FOLLOWING SPLICEDHEAD ANCHOR LOCATIONS:



















®


EXTERIOR

ANCHOR LOCATIONS F

NTS

J ROSOWSKI

16 OF 25SGD-5570


2) ABOVE FIGURES ARE FOR SPLICES OCCURRING AT THE ASTRAGAL OR INTERLOCK.FOR SPLICES OCCURRING INSIDE OF A POCKET, SEE THE EXAMPLE ON SHEET 9.


4) POCKET WALL OR CAVITY IS NOT PART OF THIS APPROVAL AND IS TO BE DESIGNEDBY OTHERS AND REVIEWED BY THE AUTHORITY HAVING JURISDICTION.

2.375" 2.375"

EXTERIOR

SPLICELOCATION

EXTERIOR

SPLICELOCATION

3.22"

4"4.75"

4"4-TRACK SPLICE




TDI-SGD5570.2



LEFT

STILE

RIGHT

STILEPANEL TYPE "F" SHOWN.

1) SEE DP/ANCHOR TABLES 1 & 2, SHEETS 7-8 FOR PANEL SIZES & DESIGN PRESSURE.

2) PANEL TYPES NOT SHOWN ARE NOT REQUIRED FOR ANY CONFIGURATIONS AND ARENOT AVAILABLE.

3) MAXIMUM NOMINAL PANEL WIDTH FOR ALL PANEL CONFIGURATIONS IS 60".

4) PANEL TYPE MAY BE EITHER EXTERIOR (STANDARD) OR INTERIOR GLAZED, BOTHTYPES QUALIFIED BY THIS APPROVAL, SEE DETAILS SHEET 10.

PANEL NOTES:

PANEL PANEL

PANEL TYPES

NTS

J ROSOWSKI

®

1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600 17 OF 25

INSIDE 90°ASTRAGALRECEIVER

FIXEDSTILE

FIXEDSTILE

ASTRAGALBOX OUT

ASTRAGALBOX IN

ASTRAGALBOX IN

SINGLEINTERLOCK

IN

SINGLEINTERLOCK

OUT

SINGLEINTERLOCK

OUT

LOCKSTILEW/ HANDLE

ASTRAGALBOX OUT

SINGLEINTERLOCK

IN

LOCKSTILEW/ HANDLE

OUTSIDE 90°ASTRAGALRECEIVER

PANELTYPES OUTSIDE 135°ASTRAGAL

RECEIVER

INSIDE 135°ASTRAGALRECEIVER

IN. 90°ASTRAGALRECEIVER

OUT. 90°ASTRAGALRECEIVER

OUT. 135°ASTRAGALRECEIVER

IN. 135°ASTRAGALRECEIVER

INTERIOR OREXTERIOR GLAZED

PA

NE

L'S

LE

FT S

TILE

TY

PE

PANEL'S RIGHT STILE TYPE

SGD-5570

DOUBLEINTERLOCK ASTRAGAL

LOCKSTILE

ASTRAGAL

SINGLEINTERLOCK

DOUBLEINTERLOCK LOCKSTILE

ASTRAGAL LOCKSTILE

DOUBLEINTERLOCK

DOUBLEINTERLOCK

DOUBLEINTERLOCK

LOCKSTILE

SINGLEINTERLOCK

SCREEN PANEL TYPES

TDI-SGD5570.2



ANCHOR PLATE TRACK INSERT

P-HOOK

ASTRAGALREINFORCEMENT

P-HOOK ADAPTOR

ASTRAGAL ADD-ONPANEL STILE, TOPAND BOTTOM RAIL

4 TRACK SILL2 TRACK HEAD/JAMB

2 TRACK SILL

FRAME SILLADD-ON

FRAME SCREWCOVER (PVC)

SILL TRACKCOVER

3 TRACK SILL

BOTTOM RAILSUPPORT

REINFORCEMENTPLATE

1 6

4

2

32 3326

17

87

3 TRACK HEAD/JAMB3

5

109

13

27 28 29INTERLOCKADAPTER31

1211

24

18

TOP, BOTTOMAND STILEREINFORCEMENT

25

5.875

8.250

10.625

1.812

1.813

5.875

8.250

10.635

1.813

.540

.062.930

.125 .550

1.000

.062

.0621.435

1.613.060 2.060

1.983.060

.100

.080

.762

5.178

.100

.100

.100

.100

2.833

1.570

.110

1.595

2.768

.182.120

.300

1.595

2.768

.182.120

.400.312

.125

2.291

3.483

.1252.141

2.710

2.116.090

2.511

.080

4.635 4.279

1.875

.100

.301

.500

.949

.100

1.261 1.261 1.261

.173.210

1-1/16"OGEE BEAD

1-1/16"BEVELED BEAD

1-3/16"OGEE BEAD

8482 83

.252

TOP, BOTTOMAND STILECOMPOSITEREINFORCEMENT

.3091.625

2.368

.188

2.975

FIXED PANEL CLIP23

.075.626

1.681

KEEPER20

.540

.062.500

.540

.062EXTENDEDKEEPER

19

1.261

7/16"BEVELED BEAD

81

.062

4 TRACK HEAD/JAMB

2.696

.100

.0702.210

.229

.046

3.713.060

1.170

.291

1.928

.061

3.345

3.345

.065

.919

.919

.060

3.452

3.209

.300

.125

2.175

1.472

.125

.070

3.326

3.247

.090

INTERLOCK CAP,EXTENDED POCKET

REINFORCEMENTBAR

REINFORCEMENTBAR COVER 2221

3.0002.607

.229.061.291

135° CORNERASTRAGAL35 36 37 38 39 40 41

NOTES:

1) SEE SHEET 4 FORSILL RISERS.

2) SEE SHEET 20FOR SCREEN PARTS.

3) ALL DIMENSIONSIN INCHES.

EXTENDED POCKETINTERLOCK ADAPTER30

7/16"SQUARE BEAD

80

.912

1.261.065

®


EXTRUSIONS

NTS

J ROSOWSKI

18 OF 25

1.406

INTERIOR JAMB COVER34

2.838

2.073 .099

135° CORNERPASSIVE MOUNT

135° CORNERASTRAGAL CAP,EXTERIOR

135° CORNERASTRAGAL CAP,INTERIOR

90° CORNERASTRAGAL

90° CORNERASTRAGAL CAP,EXTERIOR

90° CORNERASTRAGAL CAP,INTERIOR

.100.329

1.500

.075

.252 .231

SGD-5570

.912

1.681

1.681

2.025

.094

INTERLOCK .300REINFORCEMENT,STANDARD

INTERLOCK .400REINFORCEMENT,HEAVY-DUTY

TDI-SGD5570.2



FIXED PANEL CLIP

(4) ANCHORTYPE AS USEDIN INSTALLATION,TABLE A, SHEET 1

FIXEDPANELCLIP

HEADERBLOCK

(3) #8 X1" SMS

(3) #10 X1.5" SMS

KEEPER

ALL PANEL CORNERSWELDED, NO ASSEMBLY

FASTENERS

#10 X1-1/2" SMS

BOTTOM RAILSUPPORT

(2) #10 X 1" SMSTHROUGH SUPPORT,

INTO PANEL

INTERLOCKREINF. PLATE

#8 X 1"SMS

JAMB TOSILL ASSEMBLY

INTERLOCK SILL RETAINERCLIP ATTACHMENT

HEADER BLOCK TO HEADATTACHMENT JAMB TO HEADASSEMBLY

KEEPER TO JAMBATTACHMENT

PANELASSEMBLY

1) INSTALLCLIP INTO

PANELSTILE

2) INSTALL CLIPINTO FRAMEJAMB &SUBSTRATE, SEETABLE 1

INSTALL ONE BLOCK ATEACH INTERLOCK.

AT ASTRAGAL, INSTALLONE BLOCK THAT

SPANS BOTH PANELS.

INSTALL ONE ASSEMBLY AT EACH INTERLOCK

INSTALL ONE CLIP AT THEMIDSPAN OF EACH FIXED

PANEL-TO-FRAME JAMB LOCATION.

(4) #10X 2" SMS

KEEPER

INTERIOR

EXTERIOR

(4) #10 X2" SMS

#10 X2-1/2" SMS

#8 X1-1/4" SMS

REINFORCEMENT PLATE

REINF. BAR

BAR COVER

4-PANEL, 2-TRACKOXXX SHOWN

LOCKING JAMB

NOTES1) DETAILS APPLY TO 2, 3 AND 4 TRACK CONFIGURATIONS.2) SEE SHEETS 11-16 FOR ANCHOR LOCATION & SPACING.3) SEE TABLES 1 & 2 FOR REINFORCEMENT REQUIREMENTS.4) CONTINUOUS ANCHOR PLATE, ITEM #8, IS REQUIRED AT ALL FRAME ANCHOR LOCATIONS.

(2) 1/4"X 2-1/4" SMS

®


ACCESSORIES INSTALLATION

NTS

J ROSOWSKI

19 OF 25

93

94

24

92

11

INTERLOCKCLIP COVER

60

21

22

91

90

64

90

96

19

19

96

9523

93

SGD-5570

ATTACH WITH #8 X 1-1/4"@ 34-1/2" MAX O.C.

TDI-SGD5570.2



®


107

114

101

108

111

100

SCREENSIDE RAIL,LATCH

SCREENFRAMERAIL

SCREEN OXOASTRAGALADAPTER

1.202

.935

1.081 1.081

1.7781.778

.050.050

BOX SCREENBOTTOM RAIL

BOX SCREENTOP RAIL

BOXSCREENSNAP-ONBUG FLAP

BOX SCREENSIDE RAIL

BOX SCREENASTRAGALADAPTER

FRAME SILLSCREENADD-ON

BOX SCREENSILL ADD-ON

BOX SCREEN HEADAND JAMB ADD-ON

1.487.055

1.510

1.487

.060

SCREEN VINYLASTRAGALADAPTER

1.993

.875

.062

1.993

.875

.062

1.874

1.020

.062

1.3431.306

.050

.055

1.593

.372

.725

.765.040

BOX SCREEN DETAILS: STANDARD SCREEN DETAILS:

106 103

108

33

118

119

115

111

116

117

115

102

2

131

120

112

104

125121

133123

130

129132

32

122

121

127

120

100 101 102

106

104

107 108

120 121 122

123 124

1.872

1.020

.062BOXSCREENINTERLOCK

103

1.833

1.373

.063

BOX SCREENOXOASTRAGALADAPTER

105

102

1.435

.782

.062

OR 4 OR 6

1 OR 3 OR 5

OR OR

OR OR

1 3 5

1 3 5

113 OR

102

OR OR1 3 5

1 OR 3 OR 5

2 OR 4 OR 6

124

128OR

HORIZONTAL SECTIONEXAMPLE

HORIZONTAL SECTIONEXAMPLE

HORIZONTAL SECTION EXAMPLE

HORIZONTAL SECTION EXAMPLE

VERTICAL SECTIONEXAMPLE

VERTICAL SECTIONEXAMPLE

.045

SCREEN DETAILS

NTS

J ROSOWSKI

20 OF 25

111

NOTES:1) ALL DIMENSIONS IN INCHES.




PARTS LIST

NTS

J ROSOWSKI

21 OF 25

TABLE C:

®


NOTES:1) ITEMS #14-16, 46-49, 53-59, 73, 74 & 87-89, 98 & 99 ARE NOT USED ANDARE NOT PART OF THIS APPROVAL.

TABLE D: BOX SCREEN

TABLE E: STANDARD SCREEN





EXTERIOR

6"MAX.

EXTERIOR EXTERIOR

21.6"MAX.O.C.

6"MAX.

21.6"MAX.O.C.

6"MAX.

21.6"MAX.O.C.

FIGURES PERTAIN TO THE FOLLOWING JAMB ANCHOR LOCATIONS:



NOTES:1) STANDARD ANCHORLOCATIONS SHOWN. FOR 3 AND4-TRACK JAMBS, ANCHORS INTHE INTERIOR TRACK MAY BELOCATED IN THE ADJACENTTRACK AS REQUIRED TO MEETMIN. EDGE DISTANCECONSTRAINTS FROM THEINTERIOR.

2.375"

®

1070 TECHNOLOGY DRIVEN. VENICE, FL 34275(941)-480-1600 NTS

ANCHORAGE DETAILS FOR SLIDING GLASS DOORS WHEN INSTALLED WITH FRAME FIN ADDON @ HEAD AND JAMB (SHEETS 22-25)

TO ACHIEVE PROPER ANCHOREDGE DISTANCE, THE

FOLLOWING SHEETS (22-25)SHOW ANCHOR PATTERNSTHAT MUST BE USED WHEN

USING THE FRAME FIN ADDON.

NOTES

1) DETAILS APPLY TO 2, 3AND 4 TRACKCONFIGURATIONS.

2) REFER TO TABLE AFOR ANCHORCONSTRAINTS.

3) SILL ANCHORAGEWITH FIN ADDON ISUNCHANGED FROM THEBOX FRAMEANCHORAGE.

4.75"

ANCHOR LOCATIONS A

EDGEDISTANCE

EMBEDMENT

1/4" MAX.

TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A, SHEET 1.

8

99

EXTERIOR

1/4" MAX.

EDGEDISTANCE

EMBEDMENT

SUBSTRATE

8

99

2-TRACK FRAMEJAMB ANCHORAGE DETAIL

EXTERIOR

TYP. ANCHOR TYPE, EMBEDMENTAND EDGE DISTANCE PERSUBSTRATE, SEE TABLE A,SHEET 1.

SUBSTRATE

2-TRACK FRAMEHEAD ANCHORAGE DETAIL

EMBEDMENT

1/4" MAX.

EDGEDISTANCE

EXTERIOR

2-TRACK FRAMESILL ANCHORAGE DETAIL

SUBSTRATE

TYP. ANCHOR TYPE,EMBEDMENT AND EDGEDISTANCE PER SUBSTRATE,SEE TABLE A, SHEET 1.

DETA2

DETE3

DETF3

J ROSOWSKI

SGD-5570

VINYL SLIDING GLASS DOOR TDI

TDI-SGD5570.2

3/24/16

22 OF 25

JAMB ANCHORS LAYOUT (USING FRAME FIN ADDON):




EXTERIOR EXTERIOR

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE

PANELCENTERLINE





HEAD "+" INTERMEDIATE ANCHORS LAYOUT (USING FRAME FIN ADDON):

4"

3.22"

4"

EXTERIOR

PANELCENTERLINE


3.22"

4"

4"EXTERIOR

EXTERIOR



HEAD CLUSTER ANCHORS LAYOUT (USING FRAME FIN ADDON):

4"

3.22"

EXTERIOR


3.22"

4"

EXTERIOR

EXTERIOR



4"

3.22"

4"

EXTERIOR


3.22"

4"






CENTERLINE


CENTERLINE


CENTERLINE


CENTERLINE


CENTERLINE


CENTERLINE

®


ANCHOR LOCATIONS B

NTS

FIGURES PERTAIN TO THE FOLLOWING HEADCLUSTER ANCHOR LOCATIONS:

FIGURES PERTAIN TO THE FOLLOWING HEADINTERMEDIATE ANCHOR LOCATIONS:


2) TRACK-TO-TRACKDISTANCE IS 2.375": 2.375"



2.375"

UNCHAN

GED

FROM BO

X

FRAME

4"

UNCHAN

GED

FROM BO

X

FRAME

UNCHAN

GED

FROM BO

X

FRAME

UNCHAN

GED

FROM BO

X

FRAME

UNCHAN

GED

FROM BO

X

FRAME

UNCHAN

GED

FROM BO

X

FRAME

UNCHAN

GED

FROM BO

X

FRAME

3.22"

4"

J ROSOWSKI

SGD-5570


TDI-SGD5570.2

3/24/16

23 OF 25A. LYNN MILLER, P.E.

P.E.# 1069547/27/2017



HEAD 135° CORNER CLUSTER ANCHORS LAYOUT (USING FRAME FIN ADDON):HEAD 90° CORNER CLUSTER ANCHORS LAYOUT (USING FRAME FIN ADDON):

®


EXTERIOR EXTERIOR

EXTERIOR EXTERIOR

EXTERIOR

EXTERIOR EXTERIOR

EXTERIOR EXTERIOR

EXTERIOR EXTERIOR

135°

90° ANCHOR LOCATIONS C

NTS

4"

4"

4"

4" 4"

4"

4"























3) TRACK-TO-TRACKDISTANCE IS 2.375": 2.375"

FIGURES PERTAIN TO THEFOLLOWING 135° CORNER

HEAD ANCHOR LOCATIONS:


EXTERIOR4-TRACK 90° CORNER"C6" ANCHOR LOCATIONS


4"

3.22"

4"UNC

HANGED

FROM BO

X

FRAME UNC

HANGED

FROM BO

X

FRAME

UNCHAN

GED

FROM BO

X

FRAME UNC

HANGED

FROM BO

X

FRAME

4"

4"

3.22"

4"

3.22"3.22"

4"

4"

3.22"

4"

4"

4"4"4"

4"4"

J ROSOWSKI

SGD-5570


TDI-SGD5570.2

3/24/16

24 OF 25



2) ABOVE FIGURES ARE FOR SPLICES OCCURRING AT THE ASTRAGAL OR INTERLOCK.FOR SPLICES OCCURRING INSIDE OF A POCKET, SEE THE EXAMPLE ON SHEET 9.

3) TRACK-TO-TRACKDISTANCE IS 2.375":

EXTERIOR EXTERIOR

EXTERIOR

SPLICELOCATION

SPLICELOCATION

SPLICELOCATION

SPLICELOCATION

4"4"2-TRACK SPLICE


HEAD SPLICE ANCHORS LAYOUT @ INTERLOCK OR ASTRAGAL (USING FRAME FIN ADDON):

2.375"

FIGURES PERTAIN TO THE FOLLOWING SPLICEDHEAD ANCHOR LOCATIONS:







®


EXTERIOR

ANCHOR LOCATIONS D

NTS

EXTERIOR

SPLICELOCATION

EXTERIOR

SPLICELOCATION

3.22"

4"4.75"

4"4-TRACK SPLICE




UNCHAN

GED

FROM BO

X

FRAME UNC

HANGED

FROM BO

X

FRAME

2" 2"

3.22"

4" 4"

3.22"

J ROSOWSKI

SGD-5570


TDI-SGD5570.2

3/24/16

1.625

.875

.125

FRAME FIN-ADDONALUMINUM 6063-T6PART # 19033

99

25 OF 25


2017-07-27T10:23:52-0400Anthony Lynn Miller, P.E.

Documents

SERIES 5570 IMPACT RESISTANT SLIDING GLASS DOOR · 2021. 1. 27. · series 5570 impact resistant sliding glass door including pockets & 90°/135° corners general notes: 1)glazing