instructions

sherwood cot

CR238:V3/04/08© Mamas & Papas (Holdings) Ltd. 2008

IMPORTANT: RETAIN FOR FUTURE REFERENCE READ CAREFULLY

COMPONENTS

Item Name Part no. Qty

1 Fixed side 000000000000 1

2 Support rail 000000000000 2

3 Foot end 000000000000 1

Item Name Part no. Qty

4 Head end 000000000000 1

5 Drop side 000000000000 1

6 Base 000000000000 1

Before assembling your product...Do not discard any packaging until you are certain you have all the components and fittings.If any items are damaged or missing, please contact your retailer or Mamas & Papas on 0870 8307700.Allow plenty of time and space when beginning the construction of your product.

ShErwOOd COT

-2-

1

6

3

4

2

5

FITTINGS

TOOLS

HammerCross-head Screwdriver

A x 6

Dowels

B x 2

Guides

C x 2

Guide screws

D x 2

Metal studs

E x 4

Long bolts

F x 2

Short bolts

G x 4

Base brackets

H x 4

Base bracket nuts

Fitting code: 000000000000

I x 1

Allen key

-3-

-4-

STE

P 1

Insert four dowels (A) into the holes in the ends of the cots fixed side (1) top and bottom rails. Insert two dowels (A) into the holes in the ends of the support rail (2).You may need to gently tap the dowels into the holes using a light hammer.

STE

P 2

Attach the two guides (B) to the front legs of the head (3) and foot (4) ends.Slot the guide screws (C) through the guides.Tighten the screws into the ends as shown in the diagram.Important: Do not over tighten the screws. The guides must turn freely.

A

2

3

4

C

B

- 4 -

1

-5-

STE

P 3

Screw the metal studs (D) into the metal inserts in the front legs of the head end (3) and foot end (4) using the allen key (I).

STE

P 4

Attach the fixed side (1) to the cot ends.Screw four long bolts (E) through the side rails of the fixed side and into the cot ends using the allen key (I).Important: Do not fully tighten the long bolts.

D

I

3

4

1

E

- 5 -

I

-6-

Slot the dowels into the ends of the support rail (2) into the holes in the cot ends.Insert two short bolts (F) into the holes in the cot ends and screw into the support rail using the allen key (F).

With the help of another person carefully turn the cot over so that the fixed-side faces down. Ensure that the two short bolts used to attach the support rail are half tight.Lower the drop side (5) into position between the cot ends. Ensure that the plastic teething rail is at the top and that the drop side mechanism is positioned the correct way round.

STE

P 6

STE

P 5

F

Plastic teething rail

5

- 6 -

I

2

-7-

Align the metal studs (D) on the cot ends align with the plastic runners in the drop side.With the help of another person carefully pull the leg of the cot end away from the drop side to allow enough space to insert the metal stud into the plastic runner. Insert each guide into the first groove in the plastic runner one side at a time.Fully tighten the two short bolts and four long bolts used to attach the support rail and the fixed-side to the cot ends.

Align the guides (B) on the cot ends with the metal runners in the drop side (5).Insert each guide into the recess below the metal runner one side at a time. Slide the drop side towards the support rail to ensure that the guides are correctly engaged in the metal runners.

STE

P 8

STE

P 7

B

Metal runner

D

Plastic runner

5

- 7 -

-8-

STE

P 9

Slot the unthreaded ends of the four base brackets (G) into one of the three base heights that you require. Ensure that all the base brackets are at the same height and the threaded ends are facing up.Note: The lowest base height position is the safest. You should use the cot in this position as soon as your baby is old enough to sit up.

Attach the base (6) to the cot, with the information label facing up. Lower the base onto the base brackets. Ensure that the threaded ends of the base brackets fit into the holes in the corners of the base.Screw the base bracket nuts (H) onto the threaded ends of the base brackets using the allen key.

STE

P 1

0

G

H

6

- 8 -

-9-

The cot is now fully assembled. Ensure that all the fittings are fully tightened before use.

Lowering the drop side Stand in front of the drop side and grip the top rail with both hands.1 Pull the drop side up a

little. 2 Apply gentle pressure

with your leg to the bottom of the drop side.

3 Lower the drop side.

1

3

2

STE

P 1

2S

TE

P 1

1

- 9 -

-10-

STE

P 1

3

Raising the drop side Stand in front of the drop side and grip the top rail with both hands.Pull the drop side up until it locks in position.Apply firm downward pressure to the drop side to ensure it is locked in position.

- 10 -

-11-

INSTrUCTIONS FOr SAFE USE & MAINTENANCEFor reasons of safety we only recommend the use of the Mamas & Papas size 300 •mattress for this cot.

There should be a minimum of 500mm between the top of the mattress and the upper •edge of the cot side when the base is set in the lowest position.

There should be a minimum of 200mm between the top of the mattress and the upper •edge of the cot side when the base is set in the highest position. This distance is indicated by the mattress height mark engraved in the cot.

The mattress should be no more than 40mm shorter or narrower than the internal length •or width of the cot.

If you leave the child unattended in the cot, always make sure that the drop side is in the •highest position.

Never leave anything in the cot which could provide a foothold for your child to climb out •or would present a danger of suffocation or strangulation.

Ensure that there are no loose screws that could trap parts of the child’s body or clothing •(e.g. ribbons, drawstrings, necklaces) or pose a risk of strangulation.

Regularly check that all fittings and components of the cot are fully tightened and in •working order. If any parts have become worn or damaged then do not use the cot. Seek advice by calling Customer Care on: +44 (0)845 268 2000.

Do not use replacement parts that are not recommended or supplied by Mamas & Papas. •

Non-approved parts may render the repair or cot unsafe.•

Do not place your cot in proximity of an open fire and other sources of heat, such as •radiators, electric or gas fires.

Your cot may be cleaned with a damp cloth. Never use bleach or harsh abrasives.•

Due to constant updating and improvements, some components may occasionally differ slightly from the diagrams shown in these instructions. We reserve the right to change the specifications of any product without prior notice.

After sales Service: If you need assistance, spare parts or you are unhappy with any aspect of the goods please contact Customer Care on: +44 (0)845 268 2000, or e-mail us at: customer.care@mamasandpapas.com. Visit our website at mamasandpapas.com for the latest product information.

-11-

mamasandpapas.comMamas & PapasColne Bridge RoadHuddersfield, HD5 0RH, UKcustomer services helpline: +44 (0)845 268 2000customer care email: customer.care@mamasandpapas.com

-12-