1

IMPORTANT:

Go to www.extron.com for the

complete user guide and installation

instructions before connecting the

product to the power source.www.extron.com

SMK 2 • Installation Guide

Overview

ATTENTION:• All structural steps and electrical installation must be performed by qualified personnel in accordance with local and

national building codes and electrical codes.• Toute étape structurelle et installation électrique, doit être effectuée par un personnel qualifié, conformément aux codes du

bâtiment, aux codes incendie et sécurité, et aux codes électriques, locaux et nationaux.

This guide provides instructions for professional installers to mount and install the TLP Pro 725M to a wall or glass surface using the SMK 2 mounting kit. The kit consists of:

A (1) SMK 2 plastic enclosure (see figure 1) with an adhesive patch on the back.

B The SMK 2 Alignment Guide, which should be downloaded from www.extron.com.

C (1) Cover Overlay.

The kit also includes the following optional items:• (1) LED Overlay (see figure 5, 5, on the next page).• (4) M3 Screws (see figure 5, 6).

CoverOverlay

SMK 2

AlignmentGuide

y

Outer edge of

TLP Pro 725M

Bottom, inner

edge of SMK 2

(the side with the

adhesive patch)

Alignment Guide for the Extron

SMK 2

Page size: 8.5" x 11"

Print scale 1:1

Do not shrink.

1. Confirm the product to

be installed.

2. Double-check the print

settin

gs, before printing.

Make sure the scale

settin

gs are 1:1.

3. Decide where to mount

the SMK 2. Use this guide

to ensure there is enough

clearance at th

e sides

to mount th

e touchpanel.

4. Stick this guide to the

glass on the opposite

side fro

m where the

SMK 2 is being mounted.

Use a level to

make sure

the guide is horizontal.

5. Align the bottom edge of

the SMK 2 (on the side

with the adhesive patch)

with the red line on the

guide.

P/N 68-3236-01 Rev. A

SMK 2

ick thi

ass on the op

de from where the

MK 2 is being mounted.

se a level to make sure

e guide is horizontal.

ign the bottom edge of

e SMK 2 (on the side

th the adhesive patch)

th the red line on the

uide.

P/N 68-3236-01 Rev. A

C

A

B

Figure 1. SMK 2 KitBefore StartingRemove one or more knockouts from the SMK 2 enclosure to run cables to the back of the TLP Pro 725M. The SMK has four knockouts (see figure 2, A), one in the middle of each side.You may need to use a sharp knife to cut the plastic holding the knockout in place.

Option 1: Mounting the SMK 2 to a Wall with Fasteners

To mount the SMK 2 to a wall or furniture, drill holes through the four dimples in the plastic (see figure 2, B) and attach to the mounting surface.The installer must use screws that are appropriate for the mounting surface.

B

A

B

A

B

B

A

A

Figure 2. SMK 2 Knockouts and Mounting Holes

1

Outside Glass Surface

Inside GlassSurface

2

Outer edge of

TLP Pro 725M

Bottom, inner

edge of SMK 2

(the side with the

adhesive patch)

Alignment Guide for the Extron

SMK 2

Page size: 8.5" x 11"

Print scale 1:1

Do not shrink.

1. Confirm the product to

be installed.

2. Double-check the print

settin

gs, before printing.

Make sure the scale

settin

gs are 1:1.

3. Decide where to mount

the SMK 2. Use this guide

to ensure there is enough

clearance at th

e sides

to mount th

e touchpanel.

4. Stick this guide to the

glass on the opposite

side fro

m where the

SMK 2 is being mounted.

Use a level to

make sure

the guide is horizontal.

5. Align the bottom edge of

the SMK 2 (on the side

with the adhesive patch)

with the red line on the

guide.

P/N 68-3236-01 Rev. A

Outside Glass Surface

e size: 8.5" x 11"

Print scale 1:1

Do not shrink.

firm the product to

nstallead.

blee-e-ce-c-c-c

ingggssss,

e sssuuuur

ingggss gs

ideeee w

SMMMMKKK

nssuuuure

raannnncc

mouuuunnnt

k tthhhhhis

ss ooooonn

e frrooooom

K 22 2 iiis

a lleeeev

guuiiiddde

n ttthhhhe

SMMMMKKK

thhheeee

thhheeee

de..

P/N

check the print

, ra

wK 2

ecet s

n ms vee

K ar

6

heck the print

be

ar

wh2.

e t

e at

s gth

m wb

vee i b2

adre

68

eck the print

before printing.

the scale

re 1:1.

here to mountt

. Use this guguide

there is enonough

at the sidedes

he touchhpanel.

guide to o the

he oppoposite

where e the

being mmounted.

l to mmake sure

is horrizontal.

bottomm edge of

(on tthe side

dhesiive patch)

ed linee on the

8-32336-01 Rev. A

44

3

Figure 3. Place the Template

Option 2: Mounting the SMK 2 to a Glass Surface

1. Clean both sides of the glass with a lint-free cloth and a 50:50 mixture of isopropyl alcohol and water.

2. Place the SMK 2 Alignment Guide on the inside glass surface (see figure 3, 1), so that it does not get wet when you apply the soap solution.Use tape (2) to attach the alignment guide to the glass, and use a level (3) to ensure it is at the correct angle.

3. Remove the plastic backing from the adhesive patch.

TIP: Wet your fingers to prevent them from sticking to the adhesive patch.

4. Spray the adhesive patch and the outside glass surface with soap solution (two drops of detergent in a quart of water) (4).

figure 1

2 © 2018 Extron Electronics All rights reserved. All trademarks mentioned are the property of their respective owners. www.extron.com

SMK 2 • Installation Guide (Continued)

5. Carefully align the bottom inner edge of the SMK 2 with the red line on the alignment guide marked “Bottom, inner edge of SMK 2” (see figure 4, 4).You can slide the adhesive patch quite easily while it is still wet.

6. Allow the adhesive to cure at least 24 hours before attaching the touchpanel.7. Remove the paper alignment guide.

Mounting the Cover Overlay (Optional)The cover overlay is not required for mounting the touchpanel, but can improve the aesthetics of the SMK 2 when it is viewed through the window from inside the conference room. 1. Spray the inside surface of the glass with the soap solution.2. Remove the paper backing from the cover overlay (see figure 1, C, on the

previous page).

TIP: Wet your fingers to prevent them from sticking to the adhesive patch.

3. Center the cover overlay behind the SMK 2 enclosure.4. Use a credit card or similar flat edge to remove any air bubbles and a cloth

to absorb excess liquid.

TOP

Mounting Plate

LED Overlay

TLP Pro 725MTLP Pro 72TL

6

5

10

Back View

8

8

7

9

Figure 5. Mounting the TLP Pro 725M

Mounting the TLP Pro 725M

NOTE: Make sure the adhesive securing the SMK 2 to the glass has dried. Extron recommends waiting at least 24 hours before attaching the touchpanel.

1. Remove the paper backing, and attach the LED overlay to the back of the TLP Pro 725M (see figure 5, 5). This overlay covers the rear panel LEDs so that they do not cause a distraction inside the conference room.

2. Run an Ethernet cable to the SMK 2 and pass the cable through the mounting plate.

3. Fasten the mounting plate to the SMK 2 using the four M3 screws provided (6). Use the holes marked EU on the mounting plate.

4. Attach the Ethernet cable to the LAN/PoE input on the TLP Pro 725M rear panel (see the TLP Pro 725 and 1025 Series User Guide). Pass the cable through the gap left by removing the knockout (see Before Starting on the previous page).

5. The mounting plate has four hooks (7), one on each corner. Position the TLP Pro 725M so that these hooks fit into the four slots on the rear panel of the touchpanel (see the TLP Pro 725 Series and TLP Pro 1025 Series User Guide).

6. Slide the TLP Pro 725M down slightly so that the hooks are seated securely in the slots.

7. The tongue at the bottom of the mounting plate (8) sits in the groove in the bottom of the touchpanel (see inset, 9). Fasten the touchpanel to the mounting plate by tightening the lock screw (¢).

Outer edge of

TLP Pro 725M

Page size: 8.5" x 11"

Print scale 1:1

Do not shrink.

1. Confirm the product to

2. Double-check the print

settin

gs, before printing.

Make sure the scale

3. Decide where to mount

the SMK 2. Use this guide

to ensure there is enough

clearance at th

e sides

to mount th

e touchpanel.

4. Stick this guide to the

glass on the opposite

side fro

m where the

SMK 2 is being mounted.

Use a level to

make sure

the guide is horizontal.

5. Align the bottom edge of

the SMK 2 (on the side

with the adhesive patch)

with the red line on the

P/N 68-3236-01 Rev. A

Outer edge of

TLP Pro 725M

Page size: 8.5" x 11"

Print scale 1:1

Do not shrink.

1. Cononfirm the product to

2. DDouble-check the print

settings, before printing.

Make sure the scale

3. Decide where to mount

the SMK 2. Use this guide

to ensure there is enough

clearance at the sides

to mount the touchpanel.

his guide to the

opposite

he

4

to m

4. Stick this g

glass on the opp

side from where the

SMK 2 is being mounted.

Use a level

Use a level

Use a level

Use a level

Use a level

Use a level

Use a levele a level

a leve to make sur

to make sur

to make sur

to make sur

to make sur

to make sur

to make sur

to make surr

to make sur

o make surr

make surureeeeeeeeeeeeeeeee

thethe guthe guide i

the guide i

the guide i

the guide is hos horizonta

s horizontal

s horizontalal.

5. Align the bottom edgedge of

the SMK 2 (on the e side

with the adhesivesive patch)

with the red linline on the

P/NP/N 68-3236-01 Rev. A

Figure 4. Attach Adhesive Patch and SMK 2 to the Glass

figure 5

68-3233-01 Rev. B04 18