-
Solar Panels
Solar Cells Mountings
Retailer:
GB
-
© CWL 2018-10 1
Solar Panel-/ Solar Cell brackets These brackets are used to
install solar panels and similar items on the roof. Solar panels
are installed directly onto the brackets or via the supplier’s rail
system.
Waterproofing membrane roof Item no. Solar panel bracket flat
roof/profiled sheet metal roof 410009 Bolt kit bracket walkway flat
roof
-
SOLAR PANEL BRACKETS FOR SMOOTH ROOFS
M-277 1812 GB
<
cw
lun
db
erg
.co
m
Solar Panel Attachment as a Bracket
Installation on asphalt-based sealing membrane as specified in
installation instruction M-082.
Installation on roofs with PVC, ECO/FPO-based sealing membranes
as specified in M-076.
Installed with EPDM seal, nut and washer.
Use bolt kit 410226P.
Adjust the height of the bracket as needed using the bolted
joints. Installation with expandable screw, safety expanders or
chemical anchors in concrete must be done in accordance with
instructions provider from the supplier of such a bracket. Screw
dimension M10 stainless steel.
A= Carriage bolt, B= EPDM seal
Installation of Solar Panels or Similar Devices on Brackets.
Solar panels are installed onto solar panel brackets, e.g., by
screwing rails on to the carriage bolt/brackets and attaching the
solar panels onto them. Follow the instructions provided by the
solar panel supplier.
Carriage Bolt as a Bracket
Installation on bitumen-based membrane as specified in
installation instruction M-082.
Installation on roofs with PVC, ECO/FPO-based membranes as
specified in M-076.
For installation with M10 carriage bold with EPDM, bolt kit
410132P is used. Place an M10 carriage bolt into the square hole in
the centre of the mounting plate.
For installation with an M12 carriage bolt, use a stainless
steel carriage bolt of any selected length. Place the M12 carriage
bolt into the larger square hole in the mounting plate.
-
SOLAR PANEL BRACKET FOR SMOOTH ROOFS
M-270 1807 GB
<
cw
lun
db
erg
.co
m
Bracket for Sheet Metal Roofs
Steel sheet metal min 0.4 mm.
Use bolt kit 420193P.
Adjust the height of the bracket as needed using the bolted
joints.
Screw into place using a low torque for optimal threading in the
sheet metal.
Fold mount for double-folded sheet metal roofs and prefabricated
panel roofs
Steel sheet metal min 0.6 mm.
Install the fold mount onto the standing seam.
Tighten to a torque of 20-25 Nm.
A= Stainless steel building screw with washer 19 x 6.3 mm, B=
EPDM seal
Toward ridge
Installation of Solar Panels on Brackets
Solar panels are installed onto solar panel brackets, e.g., by
screwing rails onto the bracket and attaching the solar panels onto
them. Follow the instructions provided by the solar panel
supplier.
For installation onto other qualities of sheet metal, follow the
recommendations found in Installation Instruction M-124.
Folded sheet metal roof: Make sure that the bracket tabs
grasp
under the edge of the seam.
Prefabricated panel roof: Make sure that the bracket tabs grasp
the seam so that the inner seam is squeezed tightly in place.
-
MOUNTING PLATE ON PVC, ECB/FPO-BASED MEMBRANE
M-076 1807 GB
cw
lun
db
erg
.co
m
Mounting of wire system according to M-279.
Mounting plate 400 x 400 mm for installation of roof safety
devices on roofs with PVC, ECB/FPO-based waterproofing membranes
min 1.2 mm.
The waterproofing membrane must be tested in accordance with EN
13956 and satisfy the following requirements:
Tensile strength: min 500 N/50 mm EN 12311-2 Tear resistance:
min 110 N EN 12310-2 Shear strength at extension: min 450 N/50 mm
EN 12317-2 Peel adhesion at extension: min 150 N/50 mm EN
12316-2
Mounting plate installed on membrane
Attach the carriage bolt in the intended hole in the mounting
plate and place the mounting plate in the desired location.
Please note: Mounting plates on membrane roofs shall always be
mounted with 4 mounts for the following products:
Walkways, on pitches of more than 18°
End brackets for wire systems
Protective rail 1.1 m on walkways and roof ladders
Protective rail 1.1 m on low-leaning roof with membrane
Mounts (1) shall be of the same kind as used when laying the
roofing felt. These are attached to load-bearing structures through
the mounting holes in every corner.
Other products do not need a mount to load-bearing
structures.
Cut a piece of membrane measuring 500 x 500 mm. Make a hole for
the carriage bolt in the cut piece.
Weld the cut piece in the four attachment points (2) and 50 mm
around the entire mounting plate.
Attach the bracket with nut M10 A2 washer and EPDM according to
the directions for each product.
Slipguard for loose ladder M-001 Brackets, all-round brackets
and anchor loops for smooth roofs M-085, Walkway M-203, Snow fence,
Ridge and roof foot rail M-204, Roof ladder M-205, Snow stopper
tube M-224, Guardrail 1,1m for bitumen membrane roofs M-236, Rail
roof hatch and skylight M-251.
Recommended tightening torque 10 Nm.
Example bracket
Please note! Carefully check for a proper adhesion between the
welded surfaces.
-
MOUNTING PLATE ON BITUMEN-BASED MEMBRANE
M-082 1807 GB
cw
lun
db
erg
.co
m
Mounting plate 400 x 400 mm welded, without mechanical bracket,
for installation of roof safety on bitumen-based waterproofing
membrane.
The waterproofing membrane must be tested in accordance with EN
13707:2004 + A2:2009 and satisfy the following requirements:
Tensile strength: min 300 N/50 mm EN 12311-1 Tear resistance:
min 150 N EN 12310-1 Screw durability in extensions: min 500 N/50
mm EN 12317-1 Tear durability in extensions: min 125 N/50 mm EN
12316-1
Mounting plate installed under membrane
Cut a piece of the membrane measuring 500 x 500 mm. (when
renovating a roof, the mounting plate can be welded between
existing membranes and new membranes. In that case, no extra cut of
membrane measuring 500 x 500 mm is used).
Attach the carriage bolt in the intended hole in the mounting
plate and weld the mounting plate in the middle of the cut piece of
membrane.
Attach the protective cover onto the carriage bolt. Make a hole
for the carriage bolt in the overlying membrane. Completely weld
the membrane over the mounting plate.
Carefully check for a proper adhesion between the welded
surfaces.
Remove the protective cover after welding.
Attach the bracket with nut M10 A2 washer and EPDM according to
the directions for each product.
Slipguard for loose ladder M-001 Brackets, all-round brackets
and anchor loops for smooth roofs M-085, Walkway M-203, Snow fence,
Ridge and roof foot rail M-204, Roof ladder M-205, Snow stopper
tube M-224, Guardrail 1.1 m for smooth, low-pitch roofs M-236, Rail
0.5 m around roof hatch and skylight M-251, CWL Safety System
smooth roofs M-269, CWL Safety System brackets, smooth roofs
M-284,
Wire corners 15° – 90° M-291.
Recommended tightening torque 10 Nm.
Mounting plate installed on the membrane
Attach the carriage bolt in the intended hole in the mounting
plate and weld the mounting plate in the desired location.
Cut a piece of membrane 800 x 1200 mm, 880 x 1100 mm, or else
1000 x 1000 mm.
Attach the protective cover onto the carriage bolt. Make a hole
for the carriage bolt in the cut piece of membrane. Completely weld
the piece of membrane over the mounting plate.
Carefully check for a proper adhesion between the welded
surfaces.
Remove the protective cover after welding.
-
Reg no: CWL0110 GB Issue: 4
COPYRIGHT © CW Lundberg AB
T +48 71 881 15 00 [email protected] www.cwlundberg.com
Declaration of Performance - Solar Panel Bracket
1. Product's Unique Identification Code
Solar panel bracket installed in accordance with M-076, M-082,
M-270 and M-271.
Item no. Designation 410006 Solar panel bracket concrete tiles
410007 Solar panel bracket clay tiles
410009 Solar panel bracket smooth roof/profiled sheet metal
410193 Fold mount, snow stopper rake 410115 Mounting plate,
waterproofing surface
2. Intended Use for the Construction Product
Attachment of solar panels and similar devices.
3. Manufacturer's Name and Contact Address
CW Lundberg Industri AB Landsvägen 52 Box 138 SE- 792 22 Mora
Sweden Telephone number: +46 250 55 35 00 E-mail:
[email protected]
4. Specified Performance
Item no. Maximum load bearing capacity perpendicular from the
roof.
Maximum load bearing capacity in the direction of the roof.
410006 2.5 kN 6 kN 410007 2.5 kN 6 kN 410009 2.5 kN 3.7 kN
410193 3 kN 2.4 kN 410115 7 kN 10 kN Essential properties
Performance Technical specifications
Reaction to fire Class A1, Broof EN 516:2006 Durability At least
equivalent to hot galvanisation EN 516:2006 Durability Corrosivity
class C4 40 years EN ISO 12944-2
5. Other
Product performance specified in Sections 1 and 2 is consistent
with the product performance specified in Section 4. This
Declaration of Performance was issued by the manufacture at its own
responsibility as specified in Section 3.
Signed on behalf of the manufacturer by: Thomas Lundberg
Managing Director Mora, 16 January 2017
-
CW Lundberg Sp. z o.o. ul. Dworska 1 05-503 Wola Gołkowska
Poland
+48 71 881 15 00 www.cwlundberg.com [email protected]
www.cwlundberg.com
On our web page, we have gathered all of our products, as well
as installation instructions, films and the associated
documentation in order to make it safe for you
to be on the roof.
Use the Calculator - Calculate Material Consumption and Prices
Directly on the Home Page.
The brochures and the latest documentation are available on our
home page for downloading and printout; alternatively, you can
contact us and have them e-mailed/sent to you.
CWL0058 CWL0062 CWL0053 CWL0059
CW
L0
16
6-0
2 G
B
EXPERTS IN ROOF SOLUTIONS
http://www.cwlundberg.com/
