Upload
lyanh
View
224
Download
3
Embed Size (px)
Citation preview
CREATING TOMOROW’S SOLUTIONS
COATINGS I DEHESIVE® SYSTEMS I APPLICATION
1
SOLVENT FREE DEHESIVE® SYSTEMS COLOR YOUR LINER Applications Colored release liners are used to optically identify the silicone coated side of a release liner or to differentiate release layers in double sided tape applications. There are several ways to achieve a colored release liner. Colored substrates can be used, but they do not allow for differentiation of the back and front sides of the liner. Printed substrates can also be used, but the chemistry of the dye can result in inhibition of cure when siliconizing or poor anchorage of the silicone layer. DEHESIVE®
Color Pastes can be used to color release liners. New nanotechnology results in an unprecedented depth of color in silicone release coatings. Processing DEHESIVE®
Color Pastes can be combined with any solvent free DEHESIVE®
system. Typically, 5% of DEHESIVE®
Color Paste, replacing an equivalent amount of DEHESIVE®
polymer, is sufficient to achieve a deep shade at coating weights of 1 – 2 g/m². Addition of DEHESIVE®
Color Paste increases viscosity of a DEHESIVE®
system. Effect on release performance is minimal. Cleaning After coating is completed, the rolls of the coater in contact with the colored batch are wiped down thoroughly as described in the leaflet EQUIPMENT CLEANING PROCEDURE. Additionally, a run of colored DEHESIVE®
system should be followed by a colorless run using a non-white substrate to eliminate
the last traces of the DEHESIVE® Color
Paste. Silicone Products WACKER SILICONES offers a wide range of solvent free Pigment Pastes FL. Several are especially suited to be used in solvent free DEHESIVE®
systems. DEHESIVE®
Color Paste EL FL Blue 5013 DH is a ready-to-use compound. It consists of pigments and a reactive silicone polymer. It provides an intense blue color to silicone release coatings.
5% DEHESIVE®
Color Paste EL FL Blue 5013 DH added ELASTOSIL®
Color Paste FL Heliogreen 6004 is also a ready-to-use compound. It consists of pigments and a reactive silicone polymer. It provides an intense green color to silicone release coatings.
5% ELASTOSIL® Color Paste FL
Heliogreen 6004 added DEHESIVE® Release Systems Silicone release coating components can be combined and adjusted to meet various processing and performance challenges. Formulation Services WACKER’s pilot coating and application testing services can help you determine how a particular silicone release coating formulation will coat, cure and perform on your substrate under a variety of process conditions. For specific formulation advice with regards to your individual processing conditions and release targets, contact your WACKER Technical Service representative. Additional Information For further information on WACKER products consult the individual Technical Data Sheets. For additional information on options for design of your system, consult WACKER Technical Information on • SOLVENT FREE DEHESIVE®
SYSTEMS FOR PAPER LINERS • PILOT COATING SERVICES • EQUIPMENT CLEANING
PROCEDURE
CREATING TOMOROW’S SOLUTIONS
COATINGS I DEHESIVE® SYSTEMS I APPLICATION
2
AMA®, CRA® and DEHESIVE® are registered trademarks of Wacker Chemie AG.
Wacker Chemie AG, Hanns-Seidel-Platz 4, 81737 München, Germany, www.wacker.com
The data presented in this brochure are in accordance with the present state of our knowledge, but do not absolve the user from carefully checking all supplies immediately upon receipt. We reserve the right to alter product constants within the scope of technical progress or new developments. The information given in this brochure should be checked by preliminary trials because of conditions during processing over which we have no control, especially where other companies’ raw materials are also being used. The information provided by us does not absolve the user from the obligation of investigating the possibility of infringement of third parties’ rights and, if necessary, clarifying the position. Recommendations for use do not constitute a warranty, either express or implied, of the fitness or suitability of the product for a particular propose.
SP
P/H
JL/0
7.12