SPEC. SHEET NO. GT-550E-1-00102/EX-91 GT-550Eyuekchun.co.kr/jaryo/gt550e.pdf · SPEC. SHEET NO. GT-550E-1-00102/EX-91 GT-550E BOOM 5-section full power partially synchronized telescoping

CRANE SPECIFICATIONSMODELGT-550E

CAPACITY55,000 kg at 3.0 m

CRANE CAPACITY 55,000 kg at 3.0 mBOOM 5-section, 11.1 m - 42.0mDIMENSION

Overall length approx. 13,480 mmOverall width approx. 2,820 mmOverall height approx. 3,680 mm

MASSGross vehicle mass approx. 39,800 kg

-front axle approx. 15,900 kg-rear axle approx. 23,900 kg

PERFORMANCEMax. travelling speed computed 83 km/hGradeability (tan ) computed 53 %

GENERAL DATA

HYDRAULIC TRUCK CRANE

SPEC. SHEET NO. GT-550E-1-00102/EX-91

GT-550EGT-550E

BOOM5-section full power partially synchronized telescoping boom of hexagonal box construction with 6 sheaves at boom head. The synchronization system consists of 2 telescope cylinders, extension cables and retraction cables. Hydraulic cylinders fitted with holding valves. Selection of 2 boom telescoping modes. Fully retracted length....... 11.1 m Fully extended length..... 42.0 m Extension speed.............. 30.9 m in 123 s

JIB2-staged boom extension type. Triple offset (5˚ /25˚ / 45˚ ) type. Stored under base boom section.Single sheave at jib head. Length............................ 9.0 m and 14.6 m

SINGLE TOP( Auxiliary boom sheave )Single sheave. Mounted to main boom head for single line work.

ELEVATIONBy a double-acting hydraulic cylinder, fitted with holding valve. Automatic Speed Reduction and Soft Stop function. Elevation speed............... - 2˚ to 80˚ in 68 s

HOIST-Main winchVariable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and hoisting. Equipped with automatic brake (Neutral brake) and counterbalance valve. Controlled independently of auxiliary winch. Single line pull................. 42.2 kN { 4,300kgf } Single line speed............. 143 m/min (at the 4th layer) Wire rope......................... Spin-resistant type

(Non-spin type for 35 ton capacity hook block)

Diameter x length............19 mm x 227m

CARRIER : TC-4255

(주)육천건설

Yuekcun Const. Co. Ltd. http://y6000.co.kr [email protected] [email protected]

leeth

Typewritten Text

(주)육천건설 Yuekchun Const. Co. Ltd TEL +82 22691 6000 FAX +82 22691 6001 Web : y6000.co.kr E-mail1 : [email protected] E-mail2 : [email protected]

CRANE SPECIFICATIONSSPEC. SHEET NO. GT-550E-1-00102/EX-91

- 2 -

HOIST-Auxiliary winchVariable speed type with grooved drum driven by hydraulic axial piston motor through winch speed reducer. Power load lowering and hoisting. Equipped with automatic brake (Neutral brake) and counterbalance valve. Controlled independently of main winch. Single line pull................. 44.1 kN { 4,500kgf } Single line speed............. 123 m/min (at the 2nd layer) Wire rope......................... Spin-resistant type Diameter x length............ 19 mm x 127m

SWINGHydraulic axial piston motor driven through planetary speed reducer. Continuous 360˚ full circle swing on ball bearing slew ring. Automatic Speed Reduction and Soft Stop function.Equipped with manually locked/released swing brake. Swing speed.................... 1.9 min-1 { rpm }

HYDRAULIC SYSTEM Pumps............................. Quadruple gear pumps driven by carrier engine through P.T.O. Control valves.................. Multiple valves actuated by pilot pressure with integral pressure relief valves.

Circuit.............................. Equipped with air cooled type oil cooler. Oil pressure appears on AML display for main circuit.

Hydraulic oil tank capacity..... approx. 690 liters Filters............................... Return line filter

CAB AND CONTROLSBy 4 control levers for swing, boom hoist, main winch, boom telescoping or auxiliary winch with 2 control pedals for boom hoist, boom telescoping based on ISO standard layout.Control lever stands can change neutral positions and tilt for easy access to cab.One sided one-man type, steel construction with sliding door access and tinted safety glass windows opening at side.Operator's 3 way adjustable seat with headrest and armrest.

OUTRIGGERHydraulically operated H-type outriggers. Each outrigger controlled simultaneously or independently from either side of carrier. Equipped with sight level gauge. Floats mounted integrally with the jacks retract to within vehicle width. All cylinders fitted with pilot check valves. Crane operation with different extended length of each outrigger.Equipped with extension width detector for each outrigger. Extended width Fully.............................. 6,800 mm Middle........................... 4,600 mm Minimum....................... 2,390 mm Float size (Diameter)...... 400 mm

FRONT JACKA fifth hydraulically operated outrigger jack. Mounted to the front frame of carrier to permit 360˚ lifting capabilities.Hydraulic cylinder fitted with pilot check valve.Equipped with front jack extension detector. Float size(Diameter)........350 mm

COUNTERWEIGHTIntegral with swing frame Mass................................ 4,200 kg TADANO Automatic Moment Limiter (Model:AML-L)Main unit in crane cab gives audible and visual warning of approach to overload. Automatically cuts out crane motions before overload. With working range (load radius and / or boom angle and / or tip height and / or swing range) limit function.Nine functions are constantly displayed. Digital liquid crystal display: Either boom angle or moment % Either boom length or potential hook height Either actual working radius or swing angle Actual hook load Permissible load Either jib offset angle or number of parts line of rope Boom position indicator Outrigger position indicator Bar graphical display: Either moment as percentage or main hydraulic pressure (Display changes by alternation key)

NOTE:Each crane motion speed is based on unladen conditions.

(주)육천건설


CARRIER SPECIFICATIONSSPEC. SHEET NO. GT-550E-1-00102/EX-91

- 3 -

EQUIPMENT

MANUFACTURER TADANO LTD.

MODEL TC-4255 ( Left hand steering, 8 x 4 )

ENGINE [ EURO-2 ] Model.......................... NISSAN PF6 Type............................ 4 cycle, 6 cylinder in line, direct

injection, water cooled diesel engine with turbochager.

Piston displacement... 12,503 cm3

Bore x stroke.............. 133 mm x 150 mm Max. output (JIS)........ 257 kW{350PS/345hp} at 2100 min-1{rpm} Max. torque (JIS)........ 1460 Nm{150 kgfm} at 1200 min-1{rpm}

TRANSMISSION7 forward and 1 reverse speeds, synchromesh on 2nd - 7th gear and constant-mesh on 1st and reverse gear.

AXLES Front........................... Reverse - elliot type Rear............................ Full floating type

SUSPENSION Front........................... Leaf spring Rear............................ Equalizer beams and torque rods

STEERINGRecirculating ball screw type with linkage power assistance.

BRAKE SYSTEM Service........................ Full air brake with maltiprotection

valve and auto slack adjuster on all wheels, dual air line system, internal expanding leading and trailing shoe type.

Parking........................ Pneumatically controlled spring brake, acting on all rear axles.

Auxiliary....................... Electro-pneumatic operated exhaust brake.

Emergency.................. Pneumatically controlled spring brake, acting on all rear axles.

TIRES Front........................... 315/80 R 22.5 156/150, Single x 4 Rear............................ 315/80 R 22.5 156/150, Dual x 4 Spare.......................... 315/80 R 22.5 156/150, Single x 1

CABSteel construction, one sided 2-man type Driverʼs seat................ Adjustable suspension type

ELECTRIC SYSTEM24 V DC. 2 batteries of 12 V (JIS)115F51, 96Ah at 5-hour rateAlternator 24V-50A

FUEL TANK CAPACITY300 liters

FOR CRANEStandard Equipment

4.5 t capacity, hook block (swivel hook)Control pedals for boom hoist and boom telescoping3 working lightsExternal lamp(AML)Cable followerWinch drum mirror(Hoist mirror)Electric fanSun visorSun shadeCab floor mat

Optional Equipment55 t capacity, hook block (6 sheaves)35 t capacity, hook block (4 sheaves) (* in combination with non-spin wire rope for main winch)20 t capacity, hook block (2 sheaves)Drum rotation indicator for main and auxiliary winchAir conditioner (hot water heater and cooler)

FOR CARRIERStandard Equipment

Fan clutch: Viscous-typeIntake air heaterOverheating warning buzzerCooling water level warning buzzer

Engine over-run alarmPTO hour meterPassenger seatSeat belt: 3 point type for driver, 2point type for passengerTilting-telescoping steering wheelWindshield wiper(with intermittent wiping)and washerWindow glass: Tinted, Infrared and Ultraviolet raysabsorption TachometerLow air pressure warning buzzerAM/FM radioCar cooler(Refrigerant:R134a)Car heater(Hot water type)with defrosterThird differential gear lockSpeedometer(with odometer)Sun visorSpare tire carrier with lock keyTool box with lock keyFuel tank cap with lock keyBack-up lightBack-up alarmAir filter warning light(Instrument cluster)Towing hook(Front and rear, Eye type)AshtrayCigarette lighterOwner's tool setCab floor matFront and Rear fog lampsSide marker lampsR2000 Side mirrors

(주)육천건설


WORKING RANGESPEC. SHEET NO. GT-550E-1-00102/EX-91

- 4 -

BOOM

JIB

LIFT

ING

HEI

GH

T (m

)

0

5

10

15

20

25

30

35

40

45

50

55

60

65

0 5 10 15 20 25 30 35 40

5˚ 25˚

10˚

0˚

45˚

20˚

RADIUS (m)

11.1 m BOOM15.0 m BOOM

18.8 m BOOM

26.6 m BOOM

34.3 m BOOM

42.0 m BOOM

42.0 m BOOM + 9.0 m JIB

42.0 m BOOM + 14.6 m JIB70˚

50˚

40˚

60˚

80˚

30˚

NOTE: 1. Boom and jib geometry shown are for unloaded

condition and machine standing level on firm supporting surface. Boom deflection and subsequent radius and boom angle change must be accounted for when applying load to hook.

2. When the boom length is 11.1 - 12.0 m, Max boom angle is 76˚

Approx. 2.5m

Approx. 2.2m

Approx. 2.3m

0.8m

42.0 m

34.3 m

26.6 m

18.8 m

15.0 m

11.1 m

Telescoping mode

(주)육천건설


WORKING RANGESPEC. SHEET NO. GT-550E-1-00102/EX-91

- 5 -

BOOM

JIB

42.0 m

38.1 m

34.3 m

26.6 m

18.8 m

11.1 m

LIFT

ING

HEI

GH

T (m

)

RADIUS (m)

NOTE: 1. Boom and jib geometry shown are for unloaded

condition and machine standing level on firm supporting surface. Boom deflection and subsequent radius and boom angle change must be accounted for when applying load to hook.

2. When the boom length is 11.1 - 12.0 m, Max boom angle is 76˚

Approx. 2.5m

Approx. 2.2m

Approx. 2.3m

0.8m

Telescoping mode

0 5 10 15 20 25 30 35 40 0

5

10

15

20

25

30

35

40

45

50

55

60

65

11.1 m BOOM

18.8 m BOOM

34.3 m BOOM

38.1 m BOOM

26.6 m BOOM

42.0 m BOOM

42.0 m BOOM + 9.0 m JIB

42.0 m BOOM + 14.6 m JIB

5˚ 25˚45˚

10˚

0˚

20˚

70˚

50˚

40˚

60˚

80˚

30˚

(주)육천건설


40,00040,00038,10033,80030,40027,40025,00022,80021,00019,30017,90014,60011,600

9,5007,800

55,00043,70038,50034,20030,80027,80025,40023,20021,40019,70018,30015,200

3.03.54.04.55.05.56.06.57.07.58.09.0

10.011.012.014.016.018.020.022.024.026.028.030.032.034.0

28,00028,00028,00028,00028,00027,20024,70022,50020,70019,10017,60014,20011,300

9,1007,5005,1003,500

20,00020,00020,00019,80019,00018,20017,50016,80016,20015,70015,20014,30013,50011,400

9,6007,2005,500

20,00020,00020,00020,00018,90017,80016,70015,80014,20012,50010,300

8,6006,2004,5003,3002,4001,7001,200

100100100100

8,0008,0008,0008,0008,0007,6007,0006,4005,8004,9004,2003,6003,2002,8002,5002,1001,7001,4001,100

14,00014,00013,60012,80012,00011,40010,80010,200

9,3008,5007,8007,2006,2005,4004,7003,7003,0002,400

8,0008,0008,0008,0007,5006,9006,4005,5004,7004,1003,6002,8002,2001,8001,4001,000

700500

8,0008,0008,0008,0008,0007,5006,9005,9005,2004,2003,2002,5001,9001,4001,000

700450

0000

50000

100000

0333333

100333333

0666666

100666666

0100100100

50100100100

14,00014,00013,50013,00012,50011,30010,400

9,6008,8006,8005,1003,9003,0002,2001,6001,200

800500

Outriggers fully extended 6.8m

Load radius (m)

11.1 mboom

15.0 mboom

18.8 m boom 26.6 m boom 34.3 m boom 38.1 m boom

42.0 m boom

Telescoping conditions(%)

NOTES :1. Rated lifting capacities shown in the table are based on the condition that the crane is set on firm ground horizontally. Those above

bold line are based on crane strength and those below, it is stability.2. Rated lifting capacities in the stability area comply with part 2 / ISO 4305.3. The mass of load handling devices such as hook blocks {570 kg for *55 ton capacity, 410 kg for *35 ton capacity, 400 kg for *20 ton

capacity and 130 kg for 4.5 ton capacity} and slings, shall be considered part of the load and must be deducted from rated lifting capacities.

4. Without front jack extended, when the boom is within the Over-front, Rated lifting capacities are different from those for the boom in the Over-side and Over-rear.

5. Standard number of parts of line for each boom length is as shown below. Load per-line should not surpass 42.2 kN {4,300 kgf} for main winch rope and 44.1 kN {4,500 kgf} for auxiliary winch rope.*: Optional Boom Length 11.1 m 15.0 m 18.8 m 26.6 m 34.3 m 38.1 m 42.0 m Jib/Single top Number of parts of line **13/12 10 7 5 4 4 4 1**: With single top (When the lifting capacities is 55,000 kg)

6. Special weather caution: Refer to the operation and maintenance manual.7. For rated lifting capacity of single top, subtract the main hook mass from the relevant boom rated lifting capacity. Rated lifting capacity

of single top should not exceed 4,500 kg. 8. Load radius shown in the table includes the deflection of the boom. Therefore, perform it according to the load radius. However for the

jib operation, perform it according to the boom angle regardless of the boom length. The load radius shows reference value when the jib is attached to the 42.0 m boom, 38.1 m boom (Telescoping mode ) and 34.3 m boom (Telescoping mode ).

Telescoping Mode2nd boom3rd boom4th boomTop boom

SPEC. SHEET NO. GT-550E-1-00102/EX-91RATED LIFTING CAPACITIES

UNIT : kg CLASS OF CRANE ; C3

- 6 -

, ,

ISO 4305

(주)육천건설


28,00028,00028,00025,50019,20015,10012,20010,000

8,3007,0005,9004,2003,0002,1001,300

32,00032,00032,00026,30020,20015,80012,80010,600

8,9007,5006,4004,700

3.03.54.04.55.05.56.06.57.07.58.09.0

10.011.012.014.016.018.0

28,00028,00028,00024,90018,70014,60011,800

9,6008,0006,6005,5003,9002,7001,8001,000

20,00020,00020,00019,70018,90017,70014,60012,30010,500

9,1007,9006,1004,8003,8003,0001,9001,100

20,00020,00016,40013,30011,100

9,4008,0006,8005,1003,8002,9002,1001,000

100100100100

8,0008,0008,0008,0008,0007,1005,6004,6003,8002,6001,8001,200

14,00014,00013,50012,70012,00011,100

9,7008,5006,7005,3004,3003,5002,3001,500

8,0008,0008,0006,5005,2004,2003,4002,2001,400

8,0008,0007,9006,1004,8003,8003,0001,9001,000

0000

50000

100000

0333333

100333333

0666666

100666666

0100100100

50100100100

14,00011,90010,100

8,7007,5005,8004,5003,5002,7001,600

Outriggers extended to middle 4.6m

Load radius (m)

11.1 mboom

15.0 mboom

18.8 m boom 26.6 m boom 34.3 m boom 38.1 m boom

42.0 m boom


, Telescoping Mode2nd boom3rd boom4th boomTop boom



22,10016,30012,500

9,9007,9006,5005,3004,3003,5002,9002,3001,400

22,80016,90013,10010,400

8,4006,9005,7004,8004,0003,3002,7001,800

3.03.54.04.55.05.56.06.57.07.58.09.0

10.011.012.0

21,70015,90012,100

9,5007,6006,1005,0004,0003,2002,6002,0001,100

20,00018,60014,60011,900

9,8008,3007,0006,0005,2004,5003,9002,9002,2001,6001,100

11,8008,8007,3006,1005,1004,3003,6003,0002,1001,400

12,50010,400

8,8007,6006,5005,7005,0004,4003,4002,7002,1001,600

0000

50000

100000

0333333

100333333

0666666

Outriggers extended to minimum 2.39m

Load radius (m)

11.1 mboom

15.0 mboom

18.8 m boom 26.6 m boom


Telescoping Mode2nd boom3rd boom4th boomTop boom


- 7 -

,

,

ISO 4305

(주)육천건설


2,3002,3002,3002,3002,2402,1602,0201,8501,7301,5801,4501,180

920590410

3,5003,5003,5003,4003,2503,1002,8402,4302,2001,9501,7801,3501,050

680470

80˚79˚78˚77˚76˚75˚73˚70˚68˚65˚63˚60˚58˚55˚53˚

1,3001,3001,3001,2801,2601,2401,2001,1501,1201,0701,0301,000

850550

2,5002,5002,5002,3502,2202,1001,8901,6401,5001,3301,2201,080

800500

1,2001,2001,2001,1701,1401,1201,0701,000

950910850800750480

700700700690680670650630620590580570560420


Boom angle

5˚offset 25˚offset9.0 m jib

42.0 m boom

45˚offset 5˚offset 25˚offset14.6 m jib

45˚offset



2,3002,3002,3002,3002,2402,1602,0201,8501,7301,5801,4501,2801,2001,0801,000

3,5003,5003,5003,4003,2503,1002,8402,4302,2001,9501,7801,5501,3801,1501,000

840

80˚79˚78˚77˚76˚75˚73˚70˚68˚65˚63˚60˚58˚55˚53˚50˚

1,3001,3001,3001,2801,2601,2401,2001,1501,1201,0701,0301,000

980940920

2,5002,5002,5002,3502,2202,1001,8901,6401,5001,3301,2201,0801,000

890820

1,2001,2001,2001,1701,1401,1201,0701,000

950910850800770730710

700700700690680670650630620590580570560550540


Boom angle


38.1 m boom ( telescoping mode ) or less than that


45˚offset


2,3002,3002,3002,3002,2402,1602,0201,8501,7301,5801,4501,2801,2001,0801,000

3,5003,5003,5003,4003,2503,1002,8402,4302,2001,9501,7801,5501,3801,1501,000

840

80˚79˚78˚77˚76˚75˚73˚70˚68˚65˚63˚60˚58˚55˚53˚50˚

1,3001,3001,3001,2801,2601,2401,2001,1501,1201,0701,0301,000

980940920

2,5002,5002,5002,3502,2202,1001,8901,6401,5001,3301,2201,0801,000

890820

1,2001,2001,2001,1701,1401,1201,0701,000

950910850800770730710

700700700690680670650630620590580570560550540


Boom angle


34.3 m boom ( telescoping mode ) or less than that


45˚offset


- 8 -

ISO 4305

(주)육천건설


SPEC. SHEET NO. GT-550E-1-00102/EX-91RATED LIFTING CAPACITIES ISO 4305

2,3002,3002,2801,9101,5801,300

3,5003,5003,0802,5502,0901,7001,070

80˚79˚78˚77˚76˚75˚73˚

1,3001,3001,3001,2801,2601,070

2,5002,5002,5002,1901,8001,470

1,2001,2001,2001,1701,1401,010

700700700690680670


Boom angle


42.0 m boom


45˚offset


2,3002,3002,3002,3002,2001,9001,390

3,5003,5003,5003,4002,9102,4801,7801,010

80˚79˚78˚77˚76˚75˚73˚70˚

1,3001,3001,3001,2801,2601,2401,160

2,5002,5002,5002,3502,2202,1001,520

1,2001,2001,2001,1701,1401,1201,070

700700700690680670650


Boom angle


38.1 m boom (telescoping mode ) or less than that


45˚offset


2,3002,3002,3002,3002,2001,9001,390

3,5003,5003,5003,4002,9102,4801,7801,010

80˚79˚78˚77˚76˚75˚73˚70˚

1,3001,3001,3001,2801,2601,2401,160

2,5002,5002,5002,3502,2202,1001,520

1,2001,2001,2001,1701,1401,1201,070

700700700690680670650


Boom angle


34.3 m boom (telescoping mode ) or less than that


45˚offset


- 9 -

(주)육천건설


Reference

SPEC. SHEET NO. GT-550E-1-00102/EX-91WORKING AREA

1. Applicable rated lifting capacities change as the ranges of the working area, depending on the outrigger extension width and whether

the front jack is used.

2. When the swing automatic stop cancel switch is canceled, the swing does not automatically stop even if the crane becomes

overloaded.

Front

Rear

Traveling direction

Left Right

A

B

CD

EF

G

HI

J

K

KK

KL

LL

LM

MM

M

N A : Over-front areaB : Over-rear areaC : Over-side area (right)D : Over-side area (left)E : Rated lifting capacity (capacity with outriggers at

minimum extension)F : Rated lifting capacity (capacity with outriggers at middle

extension)G : Rated lifting capacity (capacity with outriggers at full

extension)H : Minimum extension width of outriggersI : Middle extension width of outriggersJ : Full extension width of outriggersK : Position of outrigger jack with the beam not extendedL : Position of outrigger jack with the beam extended

halfwayM : Position of outrigger jack with the beam extended fullyN : Front jack

Front jack extendedFL outrigger extended to fully, FR outrigger extended to fullyRL outrigger extended to middle, RR outrigger extended to fully

Front jack not extendedFL outrigger extended to fully, FR outrigger extended to minimumRL outrigger extended to middle, RR outrigger extended to minimum

-10-

(주)육천건설


SPEC. SHEET NO. GT-550E-1-00102/EX-91DIMENSION

2,72

0

MIN

2,39

0M

ID4,

600

MAX

6,80

0

400

5,480

REAR AXLECENTER 290

2,82

0

TAIL S

WING R3,650

MIN. 11100 - MAX. 42,000

3,68

0

2,65

0

4,5402,240

1,470

13,48010,915 (CARRIER)

3,9302,580

OFFSET 800

14002,900

1,690

2,1401,

240

14˚

12˚

Tread (track) - Front ...... 2,250 mm - Rear ...... 2,110 mm

Min. ground clearance ...... 230 mm (rear equalizer beam)

-11-

(주)육천건설


Printed in Japan

Specifications are subject to change without notice.

Spec. sheet No. GT-550E-1-00102/EX-91

(International Division)4-12, Kamezawa 2-chome,Sumida-ku, Tokyo 130-0014, JapanTel:81-3-3621-7750 Fax:81-3-3621-7785http://www.tadano.co.jp/indexe.htm E-mail:[email protected]

(주)육천건설


Documents

SPEC. SHEET NO. GT-550E-1-00102/EX-91 GT-550Eyuekchun.co.kr/jaryo/gt550e.pdf · SPEC. SHEET NO. GT-550E-1-00102/EX-91 GT-550E BOOM 5-section full power partially synchronized telescoping