144

Accessories and Covers

SteelCable Tray

– Tray covers are available for all classes of tray. They should be installed where falling objects may damage cables or where vertical tray run is accessible by pedestrian or vehicular traffic.

Outside cable tray runs should be covered with a Peaked Flanged cover to protect cable from the elements and excess build up of snow and ice.

Tray Covers

– These covers provide maximum mechanical protection for cables with limited heat build up. Solid covers are available with or without flange. Flanged covers have 1/2" flange.

Solid Covers

– This design offers excellent mechanical protection while allowing heat produced by cables to dissipate.

Ventilated Flanged Covers

– Peaked covers offer mechanical protection plus prevents accumulation of liquid on the cover. Peaked covers have 15° rise at the peak. Covers greater than 12" wide *available in 72" and 3 m lengths.

Peaked Flanged Covers

Solid Flanged Solid Non-Flanged

VentilatedFlanged

Peaked Flanged

Cover mounting hardware must be ordered separately.

Cover mounting hardware must be ordered separately.

Cover mounting hardware must be ordered separately.

145

Accessories and Covers

SteelCable Tray

Straight Cover Number Selection

( S P W 1 2 ) S N C - 3MaterialPrefix

SPW • Pre-Galvanized

SHW• Hot Dip Galvanized*

SSW • Stainless Steel 316

Length

72 • (72”)

144 • (12ft)

3 • (3m)

Type

SNC • Solid Non-Flanged Cover

SFC • Solid Flanged Cover

VFC • Ventilated Flanged Cover

**PFC • Peaked Flanged Cover

Width

06 • (6")09 • (9")12 • (12")18 • (18")24 • (24")30 • (30")36 • (36")

* Hot Dipped Covers only available in 72” and 1500 mm lengths.** Peaked covers greater than 12” wide available in 72” and 3m lengths only.

Straight Covers

Fitting Covers

Fitting Cover Number Selection

( S P W 1 2 ) S N C H B 9 0 2 4

Width

06 • (6")09 • (9")12 • (12")18 • (18")24 • (24")30 • (30")36 • (36")

Cover Type

SNC •Solid Non-Flanged Cover

SFC •Solid Flanged Cover

VFC •Ventilated Flanged Cover

Radius

12 • (12”)

24 • (24”)

36 • (36”)

48 • (48”)

Fitting Type

HB • Horizontal BendHT • Horizontal TeeHX • Horizontal CrossVI • Vertical Inside BendVTU • Vertical Tee DownHYR • Horizontal Wye RightHYL • Horizontal Wye Left

Degree

30 • (30o)

45 • (45o)

60 • (60o)

90 • (90o)

MaterialPrefix

SPW • Pre-Galvanized

SHW• Hot Dip Galvanized

SSW • Stainless Steel 316

*

* Required for HB & VI onlyPrefix

Prefix

Ste

elA

cces

sorie

s

Fitting Cover Number Selection

( S P W 4 1 2 ) S N C V O 9 0 2 4

146

SteelCable Tray

Fitting Covers (cont’d)

SiderailHeight

3 • (3-5/8")4 • (4")5 • (5")6 • (6")7 • (7")

CoverType

SNC •Solid Non-FlangedCover

SFC •Solid FlangedCover

VFC •Ventilated FlangedCover

Radius

12 • (12”)

24 • (24”)

36 • (36”)

48 • (48”)

Fitting Type

VO • VerticalOutsideBend

VTD • VerticalTee Down

CS • CableSupportFitting

Degree

30 • (30o)

45 • (45o)

60 • (60o)

90 • (90o)

MaterialPrefix

SPW • Pre-Galvanized

SHW• Hot Dip Galvanized

SSW • Stainless Steel 316

*

* Required for VO only

Accessories and Covers

Fitting Cover Number Selection

( S P W 1 8 1 2 ) S N C R T 1 2

Width 1

06 • (6")09 • (9")12 • (12")18 • (18")24 • (24")30 • (30")36 • (36")

Cover Type

SNC •Solid Non-Flanged Cover

SFC •Solid Flanged Cover

VFC •Ventilated Flanged Cover

Radius

12 • (12”)

24 • (24”)

36 • (36”)

48 • (48”)

Fitting Type

RT • Horizontal Reduce TeeET • Horizontal Expand TeeEX • Horizontal Expand

Tee & Reduce CrossHSR • Horizontal Straight

ReducerHLR • Horizontal Left

ReducerHRR • Horizontal Right

Reducer

MaterialPrefix

SPW • Pre-Galvanized

SHW• Hot Dip Galvanized

SSW • Stainless Steel 316

Width 2

06 • (6")09 • (9")12 • (12")18 • (18")24 • (24")30 • (30")36 • (36")

* Radius notrequired for

HSR, HLR, HRR

*

Prefix

Width

06 • (6")09 • (9")12 • (12")18 • (18")24 • (24")30 • (30")36 • (36")

Prefix

Quantity of Standard Cover Clamps Required

Straight section (6 ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 pcs.Straight section (12 ft) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 pcs.Horizontal and Vertical Bends . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 pcs.Tees . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 pcs.Crosses. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 pcs.

147

SteelCable TrayAccessories and Covers

Note: When using the Heavy Duty Cover Clamp, only half the quantity of pieces are required.

Material CoverPrefix Offset Catalogue Number

(+) Insert Cover Offset

Designed to raise cover abovetray for added ventilation.

Raised Cover Clamp

Peaked End Cap

(*) Insert Width of Tray

Used for transition between peaked covers to straight covers.

Cover

Siderail

SPW 1” SPW(+)RCCSSW 2”

3”

MaterialPrefix Width Catalogue NumberSPW 06” SPW(*)PECSHW 09” SHW(*)PECSSW 12”

18”24”30”36”

Combination Hold Down Cover Clamp

Designed to secure flat and flanged covers with hold downfeature.

Material SiderailPrefix Height Catalogue NumberSPW 3” SPW-3-CCCSSW 4” SPW-4-CCC

5” SPW-5-CCC6” SPW-6-CCC7” SPW-7-CCC

Ste

elA

cces

sorie

s

Cover Clamp

148

SteelCable Tray Accessories and Covers

Rigid indoor cover clamp forflat and flanged covers.

Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-SCCSSW 4” (Prefix)-4-SCC

5” (Prefix)-5-SCC6” (Prefix)-6-SCC7” (Prefix)-7-SCC

Heavy Duty Peaked Cover Clamp

Heavy Duty Cover Clamp

(*) Insert Width of Tray.

Wrap around design offersadded protection for ruggedapplications and outdoorconditions.Hardware included

Material Siderail WidthPrefix Height of Tray Catalogue Number

SPW 3” 06” (Prefix)-3-(*)-HCCSHW 4” 09” (Prefix)-4-(*)-HCCSSW 5” 12” (Prefix)-5-(*)-HCC

6” 18” (Prefix)-6-(*)-HCC7” 24” (Prefix)-7-(*)-HCC

30”36”

Wrap around designformed to fit peaked coverfor outdoor applications.Hardware included.

Material Siderail WidthPrefix Height of Tray Catalogue Number

SPW 3” 06” (Prefix)-3-(*)-HPCSHW 4” 09” (Prefix)-4-(*)-HPCSSW 5” 12” (Prefix)-5-(*)-HPC

6” 18” (Prefix)-6-(*)-HPC7” 24” (Prefix)-7-(*)-HPC

30”36”

(*) Insert width of tray.

Cover Joint Strip

Strip used for joining coversend to end.

Material WidthPrefix of Tray Catalogue NumberSPW 6” SPW-(*)-SCS

9”12”18”24”30”36”

(*) Insert width of tray.Note: material is plastic.

149

SteelCable TrayAccessories, Splice Plates

Splice Plate

Packaged in pairs with zincplated hardware.Provided as standard with eachstraight and/or fitting.

Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-SSPSHW 4” (Prefix)-4-SSPSSW 5” (Prefix)-5-SSP

6” (Prefix)-6-SSP7” (Prefix)-7-SSP

Expansion Splice Plate

Allows for a 1” expansion orcontraction of tray system. Packaged in pairs withhardware.

Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-ESPSHW 4” (Prefix)-4-ESPSSW 5” (Prefix)-5-ESP

6” (Prefix)-6-ESP7” (Prefix)-7-ESP

Horizontal Adjustable Plate

Material For TrayPrefix Widths Catalogue Number

SPW 6” (Prefix)-(*)06HAPSHW 9” (Prefix)-(*)09HAPSSW 12” (Prefix)-(*)12HAP

18” (Prefix)-(*)18HAP24” (Prefix)-(*)24HAP30” (Prefix)-(*)30HAP36” (Prefix)-(*)36HAP42” (Prefix)-(*)42HAPAdjustable hinge plates provide

maximum horizontal installationflexibility.Furnished in pairs withhardware.

Step Down Splice Plate

MaterialPrefix Catalogue Number

SPW (Prefix)-(*)-(**)-SDSSHWSSW

Connects siderails of differentheights.Hardware included.

(*) Insert siderail height 1(**) Insert siderail height 2

Note: Siderail height is greater than siderail height 2.

(*) Insert Siderail Height.

Ste

elA

cces

sorie

s

150

SteelCable Tray Accessories, Splice Plates

Vertical Adjustable Plate

Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-VSPSHW 4” (Prefix)-4-VSPSSW 5” (Prefix)-5-VSP

6” (Prefix)-6-VSP7” (Prefix)-7-VSPHinged vertical plates provide

maximum flexibility for changesin elevation.Packaged in pairs withhardware.

Closure End Plate

Box to Tray Plates

Designed to secure tray toelectrical panels or boxes, wallsor end supports.Packaged in pairs with hardware..

Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-BSPSHW 4” (Prefix)-4-BSPSSW 5” (Prefix)-5-BSP

6” (Prefix)-6-BSP7” (Prefix)-7-BSP

Provides closure for any tray end.Hardware included.

Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-(*)-CEPSHW 4” (Prefix)-4-(*)-CEPSSW 5” (Prefix)-5-(*)-CEP

6” (Prefix)-6-(*)-CEP7” (Prefix)-7-(*)-CEP

Reducing Splice Plate

Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-(*)-RSPSHW 4” (Prefix)-4-(*)-RSPSSW 5” (Prefix)-5-(*)-RSP

6” (Prefix)-6-(*)-RSP7” (Prefix)-7-(*)-RSP

Used in pairs to provide a straightreduction or used with a StandardSplice Plate for an offset reduction.One per package with hardware.

*Note: For Offset Reduction: Insert width to be reduced.For Straight Reduction: Insert 1/2 width to be reduced (2 required)

Example: SPW-503-RSP = 3” offset reducer

* Tray Width

151

SteelCable Tray

Accessories,Hold Down Clamps /Hardware

MaterialPrefix Catalogue Number

Standard Hold down Clamp

Designed for most indoorinstallations.Easy to use and install.Order 1/4” hardware separately.

MaterialPrefix Catalogue Number

SPW (Prefix)-HECSHWSSW

Combination Hold Down / Expansion Clamp

Order 1/4” hardware separately.

SPW (Prefix)-SHCSSW

SPW (Prefix)-SHC-HDWSSW

Hold Down Clamp

Material SiderailPrefix Height Catalogue NumberSPW 3” (Prefix)-3-HDCSSW 4” (Prefix)-4-HDC

5” (Prefix)-5-HDC6” (Prefix)-6-HDC7” (Prefix)-7-HDC

Note: Hardware included

Note: HDW = Supplied complete with 1/4” hardware

Ste

elA

cces

sorie

s

Zinc Plated Steel Self-Drilling – Tapping Screw SPW-10-SCR

152

Accessories,Hold Down Clamps /

Hardware

SteelCable Tray

Self-Drilling – Tapping Screw

MaterialPrefix Description Catalogue Number

Steel Tray Hardware

Square shoulder self-positioningcarriage bolt.

Description Material Catalogue Number

1/4” Carriage Bolt Zinc Plated Steel SPW-1/4-CB3/8” Carriage Bolt Zinc Plated Steel SPW-3/8-CB1/4” Hex. Nut Zinc Plated Steel SPW-1/4-HN3/8” Hex. Nut Zinc Plated Steel SPW-3/8-HN

3/8” Carriage Bolt 316 Stainless SS6W-3/8-CB3/8” Hex. Nut 316 Stainless SS6W-3/8-HN316 Stainless Steel 316 Stainless SS6W-3/8-HWK*Hardware Kit

* Contains 8 nuts, 8 bolts, 8 lockwashers

(*) Insert Width of Tray+ DOS = is for solid Tray

153

SteelCable TrayAccessories, Cable Protection

Wall Penetration Sleeve

Drop-Out

Frame Type Tray to Box Plate

Nylon Expansion Pad

Designed to provide a smoothradiused surface at any position onthe tray or trough bottom. Drop-Outsare easily attached using hardwareprovided.Standard Radius = 4".

Designed to pass through wallsand fire walls.Hardware included.

Note: Not Fire Rated. Fire Stop not included.

Designed to secure tray toelectrical enclosures andpanels.

Hardware included.

Allows for thermal expansionand contraction of cable traysover supports.

Material TrayPrefix Width Catalogue Number

SPW 06 (Prefix)-(*)-DOSHW 09 (Prefix)-(*)-DOSSSW 12

18243036

Material Siderail TrayPrefix Height Width Catalogue Number

Material Catalogue Number

Natural Nylon ABW-NSP

SPW 3” 06 (Prefix)-(*)-(**)-WPSSHW 4” 09SSW 5” 12

6” 187” 24

3036

+

Material Siderail TrayPrefix Height Width Catalogue NumberSPW 3” 06 (Prefix)-(*)-(**)-FBPSHW 4” 09SSW 5” 12

6” 187” 24

3036

(*) Insert Siderail Height(**) Insert Width of Tray

Ste

elA

cces

sorie

s

(*) Insert Siderail Height(**) Insert Width of Tray

154

SteelCable Tray Accessories, Barrier Strips

Inside/Outside Vertical Bend Barriers

Barrier Strips

Barrier Strips provide a methodof separating cables in tray andtrough systems. Easily installedusing supplied hardware orBarrier Strip Clamps (soldseparately). 72" Barriers areflexible for use with horizontalfittings.

Material SiderailPrefix Height *Length Catalogue Number

Preformed to fit all standardsteel vertical bends.Provided with hardware.

Barrier Strip Clamp

Barrier Strip Clamps mountBarrier Strips to Ladder rungsand Ventilated Trough bottoms.Complete mounting hardwaresupplied.

Barrier Strip Splice

Alignment splice for joiningconnecting Barrier Strips.

SBH

SB

SPW 3” 72” (Prefix)-3-(*)-SBH-72SHW 4” (Prefix)-4-(*)-SBH-72SSW 5” (Prefix)-5-(*)-SBH-72

6” (Prefix)-6-(*)-SBH-727” (Prefix)-7-(*)-SBH-72

SPW 3” 144” (Prefix)-3-SB-(*)SHW 4” 3m (Prefix)-4-SB-(*)SSW 5” (Prefix)-5-SB-(*)

6” (Prefix)-6-SB-(*)7” (Prefix)-7-SB-(*)

NOTE: 72” barriers provided with 3 SPW10SCR144”, 3m barriers provided with self drilling-tapping screw cat. no. SPW10SCR

72’’ length, 3 screw3m length, 5 screw144’’ length, 6 screw

Material Inside Bend Outside Bend SiderailPrefix Catalogue Number Catalogue Number Height

SPW (Prefix)-3-VIB-(*)-(+) (Prefix)-3-VOB-(*)-(+) 3”SHW (Prefix)-4-VIB-(*)-(+) (Prefix)-4-VOB-(*)-(+) 4”SSW (Prefix)-5-VIB-(*)-(+) (Prefix)-5-VOB-(*)-(+) 5”

(Prefix)-6-VIB-(*)-(+) (Prefix)-6-VOB-(*)-(+) 6”(Prefix)-7-VIB-(*)-(+) (Prefix)-7-VOB-(*)-(+) 7”

(*) Insert Bend Degree (+) Insert Bend Radius

MaterialPrefix Catalogue NumberSPW (Prefix)-BSCSSW

Material Catalogue NumberPlastic ABW-BSS

Note: SHW barriers are only available in 72” or 1500 mm

155

SteelCable TrayAccessories, Cable Tray Guide

Cable Tray Clamp

Cable Tray Guide

Expansion guide for single or double runs ofcable tray.No need to field drill channel or I-beam.

Clamps for single run of cable tray.No need to field drill channel or I-beam.

Vertical Tray Hanger

Material Catalogue NumberZinc Plated Steel SPW-CTGSteel Hot Dip SHW-CTGStainless Steel SSW-CTG

Material Catalogue NumberZinc Plated Steel SPW-CTCSteel Hot Dip SHW-CTCStainless Steel SSW-CTC

Material SiderailPrefix Height Catalogue Number

SPW 3” (Prefix)-(*)-VTHSHW 4”SSW 5”

6”7”

Ste

elA

cces

sorie

s

(*) Insert Siderail Height