Embed Size (px)
Citation preview
SUBMITTAL TRANSMITTAL
Date Sent 5/9/2017 Job # 2016913
Project Name 40 Tenth Avenue
Transmittal # LOT-2016913-S230
From:
Jeremy Behrhorst
Cauldwell Wingate Company
380 Lexington Avenue, New York, NY 10168
Phone: 212-983-7150 Fax: 212-983-7275
To:
Studio Gang / GEA / Arup (Submittals)
CC:
RA Consultants LLC
Aurora Capital Associates
PLEASE REVIEW AND RETURN BY: 05/23/17
return priority Standard
nmlkji Critical nmlkji
Spec Section: 030000 Submittal Type: Product Data Scope/Area:
Distribution: E-Mail w/Links (Merged Copy)
Package Company Contact Comments
Studio Gang / GEA / Arup (Submittals)
Submittal listing:
Submittal # Doc. # Doc. Date Item Subject Action
126.0 Barker Steel LEED Forms For Approval
REMARKS:
Reviewed for Compliance with Contract Documents and Specifications
SUBMISSION LINK/RETURN DOCUMENT:
126.0_Barker Steel LEED Forms_For Approval_05.09.17.pdf PDF File 664 KB
https://portal.cwingate.com/sites/2016913/Submittals/030000/030000-126.0.pdf
SUBMITTALTo: Jeremy Behrhorst Date: 05.09.17
Company: Cauldwell Wingate Job # J0368
From: Tom Wang Submittal # 018113-1.5-2
Re: 40 10th Ave Foundation
Barker Steel LEED form
Stamp by Engineer
Stamp by Architect
Signed TW Date 05.09.17
StructureTech NY
Signed Date
Cauldwell Wingate
Location: LEED reporting form -rebar
SUBMITTAL # 126.0
SUBMITTAL # 126.0
Phone: 508-473-8484 ∙ Fax: 508-473-8512
Barker Steel LLC 55 Sumner Street
Milford, MA 01757
February 16, 2017
To Whom It May Concern:
Please be advised that Barker Steel LLC furnishes, fabricates and delivers reinforcing steel that
confirms to LEED’s requirements. The reinforcing steel originates from Nucor Steel which is located in
Auburn, NY, and is manufactured within one of our local reinforcement fabrication facilities. Please
visit www.harrisrebar.com for additional information on our locations.
Barker Steel LLC confirms that the recycled content of the reinforcing steel meets the MR Credit 4.1 &
4.2 ( see certification attached) and also confirms that the material has been extracted, harvested or
recovered within 500 miles of the project site to meet the MR Credit 5.1 & 5.2 per the 2009 LEED
requirements.
Should you have any questions please do not hesitate to contact me, or visit www.nucor.com for
further information.
Sincerely,
Barker Steel LLC
Sean McDowell Contracts Manager – US East
SUBMITTAL # 126.0
Page 1 of 3
March 30, 2016
To: All Nucor Customers
Re: 2015 Recycled Content of Nucor Steel Products
Nucor Corporation is North America’s largest recycler, using approximately 20 million tons of scrap steel in 2015 to create new products. Nucor uses Electric Arc Furnace (EAF) technology at all of its steel recycling facilities. EAFs use post-consumer scrap steel material as the major feedstock, unlike blast furnace operations that use mined iron ore as the major feedstock. Nucor has prepared the following information to help calculate the recycled content for products being used in “Green Building” applications or for projects in the LEED® program. These percentages are approximate and are based on the total weight of the products. The calculations are based on 2015 scrap steel delivered and hot metal tons produced and are defined in accordance with ISO 14021:2001. More specific product information may be available from facility representatives.
Recycled Content – LEED 2009 Credit 4
2015 Recycled Steel Content of Nucor Products (% by Total Weight)
Product Group Average Recycled Content Nucor Bar Products 99.8% Nucor Beam Products 82.9%Nucor Plate Products 64.3% Nucor Sheet Products 68.9% Nucor Castrip® 96.7%
Total Nucor Steel Combined 79.7% Vulcraft Structural Products 99.8% Vulcraft Decking 68.9% Nucor Building Group 79.7% Nucor Fastener Products 99.8% Nucor Wire Products 99.8% Nucor Cold Finish 99.8%
Regional Materials – LEED 2009 Credit 5 Nucor tracks the origin of scrap shipments to our mills. Nucor can approximate the amount of scrap recovered from any project site region. Nucor owns steel and steel products manufacturing facilities throughout the US that are often within 500 miles of the project site. Please refer to the LEED Contact List (http://nucor.com/responsibility/sustainability/compliance/leed/, then click on “LEED Contact”), and contact the specific Nucor representative at the facility directly.
SUBMITTAL # 126.0
Page 2 of 3
Bar Mill Group – Darlington, SC; Norfolk, NE; Jewett, TX; Plymouth, UT; Auburn, NY; Birmingham, AL;Kankakee, IL; Jackson, MS; Seattle, WA; Marion, OH; Memphis, TN, Kingman, AZ, Wallingford, CT
2015 Approximate Recycled Steel Content Of All Nucor Bar Mill Group Products(*)
Facility Total Scrap Steel Used
Total Alloys and Other Iron Units
Total Post-consumer Recycled Content
Total Pre-consumer/ Post-industrial
Recycled Content
All 99.8% 0.2% 82.8% 17.0%The Nucor Bar Mill Group produces rebar, angles, flats, rounds and other miscellaneous shapes. The bar mill group uses recycled scrap steel for 99.8% of the feedstock.
Sheet Mill Group – Crawfordsville, IN; Hickman, AR; Huger, SC; Decatur, AL, Gallatin, KY; Castrip, IN;Castrip, AR
2015 Approximate Recycled Steel Content Of Nucor Sheet Mill Group Products(*)
Facility Total Scrap Steel Used
Total Alloys and Other Iron Units
Total Post Consumer Recycled Content
Total Pre-consumer/ Post-industrial
Recycled Content
Crawfordsville, IN 94.9% 5.1% 78.7% 16.1%
Hickman, AR 63.5% 36.5% 52.7% 10.8%
Berkeley, SC 50.6% 49.4% 42.0% 8.6%
Decatur, AL 66.1% 33.9% 54.8% 11.2%
Gallatin, KY 82.0% 18.0% 68.0% 13.9%
Nucor Castrip® Blytheville, AR
96.6% 3.4% 80.2% 16.4%
Nucor Castrip® Crawfordsville, IN
94.9% 5.1% 78.7% 16.1%
The Nucor Sheet Mill Group produces hot band, cold rolled, pickled and galvanized products. Nucor Sheet mills use varying amounts of recycled materials depending on metallurgical product demands and market conditions. The combined sheet mill total recycled content is approximately 70.2%.
Beam Group – Blytheville, AR; Huger, SC
2015 Approximate Recycled Steel Content of Beam Mill Products(*)
Facility Total Scrap Steel Used
Total Alloys and Other Iron Units
Total Post Consumer Recycled Content
Total Pre-consumer/ Post-industrial
Recycled Content
Nucor Yamato Steel, Blytheville, AR
96.6% 3.4% 78.7% 16.1%
Nucor Berkeley, Huger, SC
50.3% 49.7% 41.7% 8.5%
Nucor Beam mills produce narrow and wide flange structural beams. Nucor Yamato uses approximately 99.8% scrap steel for their feedstock. Nucor Steel Berkeley uses a higher percentage of non-scrap iron due to metallurgical product demands for sheet steel produced using the same EAF’s. The combined beam mill recycled content is approximately 90.7%.
Plate Group - Hertford County, NC; Tuscaloosa, AL
2015 Approximate Recycled Steel Content of Plate Mill Products(*)
Facility Total Scrap Steel Used
Total Alloys and Other Iron Units
Total Post Consumer Recycled Content
Total Pre-consumer/ Post-industrial
Recycled Content
Hertford County, NC 65.5% 34.5% 54.4% 11.1%Tuscaloosa, AL 62.9% 37.1% 51.9% 10.6%
The Nucor Plate combined recycled content by weight is approximately 80.0%.
SUBMITTAL # 126.0
Page 3 of 3
(*) Studies show that the recycled steel used for Nucor products consists of approximately 83% post-consumer scrap. The remaining 17% typically consists of pre-consumer scrap generated by manufacturing processes.
Vulcraft Group – Florence, SC; Norfolk, NE; Brigham City, UT; Grapeland, TX; St. Joe, IN; Fort Payne,AL; Chemung, NY; Verco Decking, Inc. – Phoenix, AZ; Fontana, CA; Antioch, CA
Joists - The bar steel for Vulcraft joists is typically obtained from one of the eleven Nucor bar mills. That would mean that the average recycled content percentage for the Vulcraft group is 99.8%. The post consumer and pre consumer recycled content have been calculated to be approximately 82.8% and 17.0% respectively.
Deck – Steel for decking produced by Vulcraft facilities is typically obtained from one of the seven Nucor sheet mills. That would mean that the Vulcraft deck products contain approximately 68.9% recycled steel. The post and pre consumer recycled content were calculated to be approximately 57.2% and 11.7% respectively. Verco Decking, Inc. may obtain steel from sources outside of Nucor that may contain lower amounts of recycled content; specific product information regarding Verco Decking, Inc. is available from facility representatives.
Products Group - Nucor Building Group –
o Swansea, SC; Waterloo, IN; Terrell, TX; Brigham City, UT;o American Buildings Company – Eufaula, AL; La Crosse, VA; Carson City, NV; El Paso, IL;o Kirby Building Systems – Portland, TN;o Gulf States Manufacturer – Starkville, MS;o CBC Steel – Lathrop, CA;
Nucor Fastener – St. Joe IN; LMP Steel – Maryville, MO; Nucor Cold Finish – Milwaukee, WI; Darlington, SC; Brigham City, UT; Norfolk, NE Nucor Steel Kingman, LLC
Nucor Building Group (Including American Buildings Company, Kirby Building Systems, Gulf States Manufacturer, and CBC Steel) – Nucor Building Group products may contain steel from all of the Nucor steel mills or obtain steel from outside of Nucor Corporation for their sheet, plate, bar and beam steel needs. The Nucor Building Systems, when using Nucor steel, contains an average of 79.7% total recycled content. The post and pre consumer recycled content was 66.2% and 13.6% respectively.
Nucor Fastener – Steel for Nucor fasteners is typically obtained from Nucor bar mills that use scrap steel as their feedstock. Some fasteners may contain high percentages of alloys that may reduce the total recycled content of the products, but Nucor Fastener products typically contain 99.8% recycled materials. The post and pre consumer recycled content would be approximately 82.8% and 17.0% respectively.
Nucor Cold Finish – Steel processed at Nucor Cold Finish is typically obtained from Nucor bar mills. The Nucor Cold Finish, when using Nucor steel, would contain an average amount of 99.8% recycled steel. The post and pre consumer recycled content would be approximately 82.8% and 17.0% respectively.
Additional information regarding specific recycled content of Nucor Corporation products group for a customer’s specific order is available from facility representatives. Additional information is available online through the Steel Recycling Institute at http://www.recycle-steel.org.
SUBMITTAL # 126.0
LEED CONTACTS
(LEADERSHIP IN ENERGY & ENVIRONMENTAL DESIGN)
UPDATED 10/07/2015 10/9/2015
LEED CONTACTS (Leadership In Energy & Environmental Design) Page 1 of 3
BAR MILLS
Nucor Steel Auburn, Inc. 25 Quarry Road Auburn, NY 13021 Mailing Address:
P.O. Box 2008 Auburn, NY 13021
Marek Rozwood 315-258-4202 [email protected]
Nucor Steel Birmingham, Inc. 2301 F.L. Shuttlesworth Drive Birmingham, AL 35234 Mailing Address:
P.O. Box 2764 Birmingham, AL 35202
Katie Rigney 205-264-8289 [email protected]
Nucor Steel Connecticut, Inc. (Bar & Wire) 35 Toelles Road Wallingford, CT 06492 Mailing Address:
P.O. Box 928 Wallingford, CT 06492
Reed Raggio 203-265-0615 [email protected]
Nucor Steel Jackson, Inc. 3630 Fourth Street Flowood, MS 39232 Rick Downey 601-936-6248 [email protected]
Nucor Steel Kankakee, Inc. One Nucor Way Bourbonnais, IL 60914 Carmen Costales 815-939-5591 [email protected]
BAR MILLS (cont.)
Nucor Steel Marion, Inc. 912 Cheney Ave. Marion, OH 43302 Shelley Robison 740-223-4353 [email protected]
Nucor Steel Memphis, Inc. (Special Bar Quality) 3601 Paul R Lowry Road Memphis, TN 38109 Kevin Willis 901-786-5890 [email protected] Rob Simpson 901-786-5255 [email protected]
Nucor Steel Nebraska 2911 East Nucor Road Norfolk, NE 68701 Mailing Address:
P.O. Box 309 Norfolk, NE 68702
April Martens 402-644-0354 [email protected]
Nucor Steel Seattle, Inc. 2424 SW Andover Seattle, WA 98106 Jeffrey Eis 206-933-2205 [email protected]
Nucor Steel - South Carolina 300 Steel Mill Road Darlington, SC 29540 Tammy Kelly-Howle 843-398-5537 [email protected] Jason Pugh 843-398-8873 [email protected]
BAR MILLS (cont.)
Nucor Steel - Texas 8812 Highway 79 West Jewett, TX 75846 Mailing Address:
P.O. Box 126 Jewett, TX 75846
Bryan Linton 903-626-6245 [email protected]
Nucor Steel - Utah West Cemetery Road Plymouth, UT 84330 Mailing Address:
P.O. Box 100 Plymouth, UT 84330
Mollie Larson 435-458-2395 [email protected]
BEAM MILLS
Nucor Steel - Berkeley 1455 Hagan Avenue Huger, SC 29450 Mailing Address:
P.O. Box 2259 Mt. Pleasant, SC 29465
Jennifer Hawthorne 843-336-6255 [email protected]
Nucor-Yamato Steel Company 5929 East State Highway 18 Armorel, AR 72310 Mailing Address:
P.O. Box 1228 Blytheville, AR 72316
Tony Hodge 870-762-7164 [email protected] Ryan Stringer 870-762-5500, ext 215 [email protected]
PLATE MILLS
Nucor Steel - Hertford 1505 River Road Cofield, NC 27922 Mailing Address:
P.O. Box 279 Winton, NC 27986-0279
Elizabeth Pierce 252-356-3928 [email protected]
Nucor Steel - Tuscaloosa, Inc. 1700 Holt Road, N.E. Tuscaloosa, AL 35404 Michael Corbell 205-562-1181 [email protected]
SHEET MILLS
Nucor Steel - Arkansas 7301 East County Road 142 Blytheville, AR 72315 Mailing Address:
P.O. Box 30 Armorel, AR 72310
Wayne Turney 870-838-2379 [email protected]
Nucor Steel – Berkeley 1455 Hagan Avenue Huger, SC 29450 Mailing Address:
P.O. Box 2259 Mt. Pleasant, SC 29465
Jennifer Hawthorne 843-336-6255 [email protected]
SHEET MILLS (cont.)
Nucor Steel - Decatur LLC 4301 Iverson Blvd Trinity, AL 35673 Mailing Address:
P.O. Box 2249 Decatur, AL 35609-2249
Carey Bullard 256-301-3541 [email protected]
Nucor Steel – Gallatin 4831 U.S. Hwy 42 West Ghent, KY 41045 Chris Melton 859-567-3141 [email protected]
Nucor Steel – Indiana 4537 South Nucor Road Crawfordsville, IN 47933 Shawn Aker 765-364-1323, Ext. 6510 [email protected]
COLD FINISH BAR
Nucor Cold Finish Wisconsin, Inc.
7200 South 6th Street Oak Creek, WI 53154 Steve Korslin 414-856-1964 [email protected]
Nucor LMP Steel, Inc. 2000 East First Street Maryville, MO 64468 Rick Liberty 660-582-3127, Ext. 391 [email protected]
Nucor Steel - South Carolina 300 Steel Mill Road Darlington, SC 29540 Tammy Kelly-Howle 843-398-5537 [email protected] Jason Pugh 843-398-8873 [email protected]
SUBMITTAL # 126.0
LEED CONTACTS
(LEADERSHIP IN ENERGY & ENVIRONMENTAL DESIGN)
UPDATED 10/07/2015 10/9/2015
LEED CONTACTS (Leadership In Energy & Environmental Design) Page 2 of 3
COLD FINISH BAR (cont.)
Vulcraft - Nebraska 1601 West Omaha Avenue Norfolk, NE 68701 Mailing Address:
P.O. Box 59 Norfolk, NE 68702
Dwight Eisenbraun 402-644-8552 [email protected]
Vulcraft - Utah 1875 West Highway 13 South Brigham City, UT 84302 Mailing Address:
P.O. Box 637 Brigham City, UT 84302
Aaron Bell 435-734-4443 [email protected]
WIRE
Nucor Steel - Connecticut, Inc. (Bar & Wire) 35 Toelles Road Wallingford, CT 06492 Mailing Address:
P.O. Box 928 Wallingford, CT 06492
Reed Raggio 203-265-0615 [email protected]
Nucor Steel – Kingman, LLC (Bar & Wire) 3000 West Old Hwy 66 Kingman, AZ 86413 Mark Vanik 928-718-7035, Ext. 203 [email protected]
BUILDING SYSTEMS
American Buildings Co - AL 1150 State Docks Road Eufaula, AL 36027 John Howard 334-688-2279 [email protected]
American Buildings Co - IL 2101 East Main El Paso, IL 61738 Cheryl Luning 309-527-5420 [email protected]
American Buildings Co - NV 2401 Conestoga Drive Carson City, NV 89706 Damaris Pierrott 775-887-2900 [email protected]
American Buildings Co - VA 501 Golden Eagle Drive La Crosse, VA 23950 Mailing Address: Sara Fulks 434-757-2220, ext 40 [email protected]
CBC Steel Buildings 1700 E. Louise Ave. Lathrop, CA 95330 Claudia Gomez 209-983-0910 [email protected] Jason Johnston 209-983-0910, Ext. 103 [email protected]
BUILDING SYSTEMS (cont.)
Gulf States Manufacturers 101 Airport Road Starkville, MS 39759 Mailing Address:
P.O. Box 1128 Starkville, MS 39760
Dave Bragg 662-324-8743 [email protected]
Kirby Building Systems 124 Kirby Drive Portland, TN 37148 Mailing Address:
P.O. Box 390 Portland, TN 37148
Rick Nelson 615-745-6044 [email protected]
Nucor Building Systems - Indiana 305 Industrial Parkway Waterloo, IN 46793 Greg White 260-837-9221 [email protected]
Nucor Building Systems - South Carolina 200 Whetstone Road Swansea, SC 29160 Mailing Address:
P.O. Box 1006 Swansea, SC 29160
Mike Snelling 803-568-2100, Ext. 178 [email protected]
BUILDING SYSTEMS (cont.)
Nucor Building Systems - Texas 600 Apache Trail Terrell, TX 75160 Jason Lengacher 972-524-5407, Ext. 2908 [email protected]
Nucor Building Systems - Utah 1050 North Watery Lane Brigham City, UT 84302 Mailing Address:
P.O. Box 907 Brigham City, UT 84302
Kurt Robinette 435-919-3140 [email protected] Casey Christiansen 435-919-3198 [email protected]
SCREWS & BOLTS
Nucor Fastener - Indiana 6730 County Road 60 St. Joe, IN 46785 Mailing Address:
P.O. Box 6100 St. Joe, IN 46785
Tony DePietro 260-337-1667 [email protected]
JOISTS & DECKING
Verco Decking, Inc. (Decking) 4340 North 42nd Avenue Phoenix, AZ 85019-3302 Megan Hallenbeck 602-353-2002 [email protected]
JOISTS & DECKING (cont.)
Vulcraft - Alabama (Joists & Decking) 7205 Gault Avenue North Fort Payne, AL 35967 Mailing Address:
P.O. Box 680169 Fort Payne, AL 35968
Loretta Bean 256-845-2460, Ext. 5170 [email protected]
Vulcraft - Indiana (Joists & Decking) 6610 County Road 60 St. Joe, IN 46785 Mailing Address:
P.O. Box 1000 St. Joe, IN 46785
Tim Jones 260-337-1884 [email protected]
Vulcraft - Nebraska (Joists & Decking) 1601 West Omaha Avenue Norfolk, NE 68701 Mailing Address:
P.O. Box 59 Norfolk, NE 68702
Dwight Eisenbraun 402-644-8552 [email protected]
Vulcraft - South Carolina (Joists & Decking) 1501 West Darlington Street Florence, SC 29501 Mailing Address:
P.O. Box 100520 Florence, SC 29501
David Conner 843-664-2259 [email protected]
SUBMITTAL # 126.0
LEED CONTACTS
(LEADERSHIP IN ENERGY & ENVIRONMENTAL DESIGN)
UPDATED 10/07/2015 10/9/2015
LEED CONTACTS (Leadership In Energy & Environmental Design) Page 3 of 3
JOISTS & DECKING (cont.)
Vulcraft - Texas (Joists & Decking) North Main Street Extension Grapeland, TX 75844 Mailing Address:
P.O. Box 186 Grapeland, TX 75844
Jim Thorpe 936-687-3107 [email protected]
CORPORATE
Nucor Corporation 1915 Rexford Road Charlotte, NC 28211 Keith Lindemulder [email protected]
Vulcraft of New York, Inc. (Joists & Decking) 621 Main Street PO Box 280 Chemung, NY 14825 John Slovak 607-529-9016 [email protected]
Vulcraft - Utah (Joists) 1875 West Highway 13 South Brigham City, UT 84302 Mailing Address:
P.O. Box 637 Brigham City, UT 84302
Aaron Bell 435-734-4443 [email protected]
SUBMITTAL # 126.0
