Submitted by - College of Engineering, Guindy · Figure 1.6 Installing and Updating Mumble Server in Raspberry pi using the terminal 1. sudo apt update && sudo apt install mumble-server

WIRELESS INTERCOM

A Project Report

Submitted by

V. BHARATH RAJ- 2016105018

V.PRANESH- 2016105568

SURAJ SURESH- 2016105598

For the Summer Internship Course

In

ELECTRONICS AND COMMUNICATION ENGINEERING

DEPARTMENT OF ELECTRONICS AND COMMUNICATION

ENGINEERING

ANNA UNIVERSITY

CHENNAI

MAY 2018

- 1 -

TABLE OF CONTENTS:

S.No. Contents Page

1 Acknowledgement 2

2. Abstract and Overview of the Project 3

3. Introduction 4

4. Getting Started with the Raspberry Pi

(i) Installing NOOBS or Raspbian OS onto the SD card.

(ii) Working with the Raspberry Pi.

6

6

7

5. Configuring the Raspberry Pi with the Mumble Server 10

6. Configuring our Mobile devices 15

7. References 20

8. Manual

(i) To establish a Full Duplex Call

(ii) To establish a Half Duplex Call

(iii) To establish a Group Call

(iv) To create a chatroom

20

20

24

28

31

- 2 -

1. ACKNOWLEDGEMENT

We are highly indebted to our project mentor Dr M A Bhagyaveni,

Professor, Dept. of ECE for her continuous supervision, motivation and guidance

throughout our tenure of our project.

We would like to thank the Dean, CEG, and the Head, Dept. of ECE, Anna

University for giving us the opportunity to undergo this summer internship

programme.

We would like to express our sincere thanks to Dr Sridharan, Professor,

Dept. of ECE, CEG, who is the coordinator of this summer internship, for helping

us in joining this programme.

We thank the Ph.D., Scholars, Dept. of ECE, CEG, for their continuous

helping and suggestions during our project.

Last but not least we thank all the staff members of the Dept.nt of ECE for

their encouragement and support.

V. BHARATH RAJ V.PRANESH SURAJ SURESH

- 3 -

2. ABSTRACT AND OVERVIEW OF THE PROJECT

In this project we will be setting up a Wireless intercom using the Raspberry Pi 3

Model B. The contributions of this project are : to establish

(i) Full duplex communication between two users

(ii) Half duplex call like walki talki

(iii) Text messages and also to perform

(iv) Conference call between many users

These are done within the coverage range of Raspberry pi without much cost. In

this project the raspberry pi is programmed to operate as server using raspbian

OS, the mumble software is installed in the mobile to interact with the server and

establish the service.

- 4 -

3. INTRODUCTION

RaspberryPi :

The Raspberry Pi is a low cost, credit-card sized computer that plugs into a computer

monitor or TV, and uses a standard keyboard and mouse. It is a capable little device

that enables people of all ages to explore computing, and to learn how to program in

languages like Scratch and Python. It’s capable of doing everything you’d expect a

desktop computer to do, from browsing the internet and playing high-definition

video, to making spreadsheets, word-processing, and playing games.

The Raspberry Pi has the ability to interact with the outside world, and has been used

in a wide array of digital maker projects, from music machines and parent detectors

to weather stations and tweeting birdhouses with infra-red cameras. We want to see

the Raspberry Pi being used by kids all over the world to learn to program and

understand how computers work.

Here in this project we have used a Raspberry Pi 3 Model B as shown below.

Figure 1.1 Raspberry PI’s Parts

- 5 -

Figure1.3 Mumble App

Mumble Server:

A Mumble server (called Murmur) has a root channel and a hierarchical tree of

channels beneath it. Users can temporarily connect channels to create larger virtual

channels. This is useful during larger events where a small group of users may be

chatting in a channel, but are linked to a common channel with other users to hear

announcements. It also matches team-based first-person shooter (FPS) games. Each

channel has an associated set of groups and access control lists which control user

permissions. The system supports many usage scenarios, at the cost of added

configuration complexity.

Mumble application is an Open-Source Platform and it can be

found available in the Google Play Store.

Figure 1.2 Mumble’s logo

- 6 -

4. GETTING STARTED WITH RASPBERRY PI

Here we will be learning on how to get started with the Raspberry Pi. Also on how to

setup the Raspberry Pi on our first Boot. The required materials are provided below,

Hardware:

o A Raspberry Pi computer with an SD card

o A monitor with a cable (and, if needed, an HDMI adaptor)

o A USB keyboard and mouse

o A power supply

o Headphones or speakers (optional)

o An Ethernet cable (optional)

Software:

o Raspbian, installed via NOOBS

STEP 1:

Installing the NOOBS or the Raspbian OS onto the SD card.

Here in this step we will be installing the Raspbian Operating System in the SD card

(minimum 16GB free space required).

➢ Initially before starting the SD card must be formatted so that the OS runs without

problem. To format the SD card, if you are using Windows OS download the SD

card formatter from the link below.

https://www.sdcard.org/downloads/formatter_4/

➢ Insert the SD card onto a SD card reader and then in the formatter select the required

drive that need to be formatted.

➢ Now install the NOOBS or the Raspbian OS from the official Raspberry Pi website

https://www.raspberrypi.org/downloads/raspbian/

https://www.sdcard.org/downloads/formatter_4/

https://www.raspberrypi.org/downloads/raspbian/

- 7 -

➢ Now the installed OS file has to be written as an image file into the SD card so

for this we require a software named, Windows32disk Imager. Download this

from the link as below,

https://sourceforge.net/projects/win32diskimager/

➢ Using this Disk Imager the image file is now written into the SD card and is now

ready to be inserted into the Raspberry Pi.

STEP 2:

WORKING WITH RASPBERRY PI:

METHOD 1:

Connecting Raspberry Pi with an HDMI display.

Here the Raspberry Pi is connected to the HDMI display via the HDMI port available

in the Pi module.

➢ If in case we do not have a monitor with an HDMI Port the Pi is connected

through an HDMI-VGA or DVI adapter. The adapter is easily available and is as

shown.

➢ As soon as you connect the Raspberry Pi with and HDMI display the Pi will boot

up automatically during the first boot some of the parameters of the pi must be

configured such as the Time Zone, Language etc.….

NOTE:

Figure 1.4 HDMI to VGA adapter

https://sourceforge.net/projects/win32diskimager/

- 8 -

➢ If in case on the first Boot-up of the Pi the HDMI display shows ‘No Signal’ or

The screen remains Blank the following configuration changes must be applied

in the ‘CONFIG.TXT’ which is present in the SD card drive.

CONFIGURATION CHANGES FOR THE HDMI DISPLAY

In the ‘config.txt’ text file the following changes in the code must be applied for

the proper display.

Applying these changes enables the user the work on the Graphical User

Interface of the Raspbian OS

#hdmi_force_hotplug=1

#hdmi_drive=2

To solve the problem you just have to uncomment (ie remove the sign # at the

beginning) these lines and save the file (Ctrl + o, Enter, Ctrl + x with nano).

Restart your Raspberry Pi and you’re done!

Just for information, here is what these two lines do:

• hdmi_force_hotplug=1:

Forces to display through HDMI event if no HDMI screen is detected. Remember

to re-comment this line if you need to display the Raspberry Pi on a different port

than the HDMI.

• hdmi_drive=2:

Trying to use HDMI mode rather than DVI mode, this allows you to solve certain

sound problems.

METHOD 2:

SETTING UP THE RASPBERRY PI FOR WINDOWS OS

- 9 -

In order to work with the Raspberry Pi using the Laptop with a Windows OS the ‘VNC Viewer’

must be used through which the Graphical User Interface of the Raspbian OS can be accessed.

Downloading and Working with the VNC Viewer:

STEP 1:

➢ The VNC Viewer is open-source and can be downloaded from

https://www.realvnc.com/en/connect/download/viewer/

➢ VNC is thus extracted and is downloaded and is available for accessing the Raspberry

Pi.

STEP 2:

➢ Power up the Raspberry Pi and the Wi-Fi module that is present in the Pi can be

connected through the ‘Mobile Hotspot’ of the Laptop.

➢ Turning on the Mobile Hotspot in the Laptop will connect automatically with the

Raspberry Pi and the IP Address of the Raspberry Pi will be displayed.

➢ This IP Address is then entered into the VNC Server and the GUI of the Raspberry Pi

is then displayed. The ‘Username’ and the ‘Password’ of the Raspberry Pi are default

and they are

USERNAME: pi.

PASSWORD: raspberry.

➢ Thus now we are ready to work with the Raspberry Pi in a GUI

environment provided by the VNC server. All the inbuilt applications and

the ‘Terminal’ within the Pi can be directly accessed.

https://www.realvnc.com/en/connect/download/viewer/

- 10 -

Figure 1.5 Raspberry pi’s desktop in VNC viewer

5. Configuring the Raspberry Pi with the Mumble Server:

With our Raspberry Pi powered up and at the Desktop, we need to open a terminal

and install the Mumble server software.

- 11 -

Figure 1.6 Installing and Updating Mumble Server in Raspberry pi using the terminal

1. sudo apt update && sudo apt install mumble-server

Next step is to configure mumble-server. In the terminal type

1. sudo dpkg-reconfigure mumble-server

Figure 1.7 configuration of Mumble server

- 12 -

A new menu will appear and it will ask you a series of questions. We need to do the

following.

➢ Set Autostart to Yes

➢ Set High Priority to Yes

➢ Create a SuperUser password.

Once completed close the menu to finalise the configuration.

The next step provides both security and means to identify the “Channel”.

In a terminal type the following command to open the mumble server configuration

file.

1. sudo leafpad /etc/mumble-server.ini

Figure 1.8 configuration of Mumble server-setting the password

- 13 -

Figure 1.9 Setting the password for the server

Scroll down the file and look for “registerName”

1. registerName=HomeIntercom

Then look for “serverpassword” and set this to a password that will be used by all

those that wish to connect.

1. serverpassword=*****

Save the file and then close the editor.

In the terminal type the following command to restart the service that is running our

server and reload the configuration files.

1. sudo service mumble-server restart

The reload should produce no errors.

The last step on the Raspberry Pi is to fix our IP address and to do this we need to

edit a configuration file.

In the terminal type

1. hostname –I

Write down your IP address and when ready edit the file by typing this line into the

terminal.

1. sudo leafpad /etc/dhcpcd.conf

- 14 -

Figure 1.10 Changing the IP address to our PI’s IP address

The lines that needed changes look as follows

1. # example static IP configuration:

2. # interface eth0

3. # static ip_address=192.168.137.228

4. # static routers=192.168.137.228

5. # static domain_name_servers=192.168.137.228 8.8.8.8

We will need to uncomment these lines by removing the “#” and change the

corresponding line to match those issued by your router and the IP address your Pi

currently has. In our case our Ip address was 192.168.137.228, and our router has an

IP address of 192.168.137.228. We also added to DNS (Domain Name Servers) so

that our Pi was able to connect to the Internet. The first is our router, the second is

Google’s DNS server.

- 15 -

Here is our example, change it to match yours and then save the file.

1. # example static IP configuration:

2. interface eth0

3. static ip_address=192.168.137.228

4. static routers=192.168.137.228

5. static domain_name_servers=192.168.137.228 8.8.8.8

Our server is now configured and ready for use. So let's power down the Raspberry

Pi, remove every accessory apart from the microSD card, power and Ethernet. Now

place the Pi somewhere safe and power it up.

6. Configuring our mobile devices

Install the Mumble client on your Android device.

Open the Mumble app and you will be asked to press the Menu key to configure a

server. The Menu key are the three dots present in the bottom right of the screen.

Press that and then press the Add Server button.

- 16 -

Figure 1.11 Adding the server in Plumble app in Android devices

In the next screen enter the details for your Mumble server. The label option is

optional and it is used if you have multiple servers saved in the Mumble client. The

address is our server address, the port for Mumble is always 64738 by default.

Username is where we can identify this Mumble device on the network, so call it

either a room or something personal. The password is the same password we set in

the Mumble server configuration file. Enter the details and then press Add Server.

- 17 -

To connect to the server press the entry in the list of Servers.

Figure 1.12 List of servers added

- 18 -

You will hear a robotic voice that tells that you are connected. Now connect another

device and start a conversation! All you need to do is press PTT (Push To Talk) and

then speak!

Figure 1.13 Inside the server

- 19 -

There is even a text chat facility built in to Mumble where groups can chat and share

information!

Figure1.14 Chatroom

- 20 -

7. References

Introduction from

https://www.raspberrypi.org/forums/

Configuration of mumble server from

(i) https://www.electromaker.io/project/view/create-your-own-home-

intercom-using-raspberry-pi-and-mumble#to-complete-this-

project-you-will-need-

(ii) https://pimylifeup.com/raspberry-pi-mumble-server/

8. Manual

To establish a Full Duplex call:

➢ Power up the raspberry pi using a adapter of 2.5A and 5V and it looks like

this,

Figure 1.15 Powering the Raspberry pi

https://www.raspberrypi.org/forums/

https://www.electromaker.io/project/view/create-your-own-home-intercom-using-raspberry-pi-and-mumble#to-complete-this-project-you-will-need-



https://pimylifeup.com/raspberry-pi-mumble-server/

- 21 -

➢ Install the plumble app on your devices.

➢ Open it and click on the “+” icon to add new networks.

➢ Enter the Username as you wish, the Password that you had given before

and the IP address of the PI.

Figure 1.17 Plumble app screen

- 22 -

➢ Repeat this in your other devices too.

➢ The page appears like this.

Figure 1.18 Server Details

Figure 1.19 List of Servers

- 23 -

➢ Open the server.

➢ Make sure you are in the “Channel” page.

➢ Click on the three stacked dots in the top right corner and follow,

Transmit mode > Continuous

➢ Now you are ready to make a full duplex call between the users in the

network.

➢ The Mic and Speaker Icons are used to mute and deafen the call. (Refer

Fig 1.20)

➢ The red microphone indicates that you are speaking.

Figure 1.20 In channel call

- 24 -

To establish a Half Duplex Call:


this,




- 25 -





- 26 -

➢ Repeat this in your other devices too.





Transmit mode > Push To Talk

➢ Now you are ready to make a half-duplex call between the users in the

network.

➢ Press and hold the PTT button when it is your turn to speak.


Fig 1.20)



- 27 -

Figure 1.25 In channel call

- 28 -

To establish a Group Call:


this,




- 29 -





- 30 -

➢ Repeat this in your other devices too.(More than two)




➢ The members in the network will be listed in the server.


Transmit mode > Continuous

➢ Now you are ready to make a group call among the users in the network.


Fig 1.20)



- 31 -

To Create a Chatroom:


this,





- 32 -



➢ Repeat this in your other devices too.(More than two)



- 33 -


➢ Swipe to the right and you will get to see the “Chat” page.


Figure 1.34 Chat Page

- 34 -

➢ You are now ready to chat with the users in the network.

Figure 1.35 Sending Message

Figure 1.36 Receiving Message

- 35 -

V. Bharath Raj V. Pranesh Suraj Suresh

Attendance

Evaluation:

Remarks:

Teacher in charge Coordinator Head of the

department

- 36 -

Documents

Submitted by - College of Engineering, Guindy · Figure 1.6 Installing and Updating Mumble Server in Raspberry pi using the terminal 1. sudo apt update && sudo apt install mumble-server