Upload
others
View
10
Download
0
Embed Size (px)
Citation preview
Multiwall Polycarbonate Standing Seam Architectural System
Installation Guide
SUNPAL®
2
System Components
Component Drawing Suppliance Data
Polycarbonate Joiner Length: 12,000m
Polycarbonate Joiner End-cap Quantity: Loose Colors: Clear
T-Fastener 10mm18mm
Quantity: Loose Sizes: 10mm, 18mm Finish: Stainless steel
T-Lock 10mm18mm
Quantity: Loose Sizes: 10mm, 18mm Finish: Stainless steel
Wood ScrewGalvanized Hex-head tapping screw 4.8x25mm (1”)
Quantity: 50/bags
Metal ScrewGalvanized Hex-head self-drilling screw 4.8x19mm (3/4”)
Quantity: 50/bags
Blocking (Solid) Tape 10mm 18mm
Quantity: 50m / Roll
Breather (Ventilated) Tape 10mm 18mm
Quantity: 33m / Roll
3
Do not step directly on the sheets between the purlins!When installing SUNPAL or doing maintenance work, always consider the sheet to be unfit to support a person’s weight. Always use stepping ladders or crawling boards, supported by minimum three roof structural elements, when working on a glazed roof of any kind.
Safety comes first
Component Drawing Suppliance Data
Aluminum Joiner * For vertical application please consult your local palram distributor.
Length: 7mFinish: Anodized
End-Cap for Aluminum Joiner Finish: Mill/Anodised
Aluminum Sealing Strip 10mm18mm
Length: 6mFinish: Anodised
Aluminum F-Profile 10mm18mm
Length: 6mFinish: Anodised
4
2a . Slit for AL Sealing Strip on bottom and top edge
Slit for T-Stoppers
90O 90O
2b
1. Cut to Size - Sheet Length 1
2a
20 mm
Pre-SUNPAL installation - Preparation of SUNPAL panels before installation
A
t=2 mm A = distance between sheet top edge to center line of purlin support
2b . Slit for T-Stoppers
5
Pre-SUNPAL installation - Preparation of SUNPAL panels before installation
3. Recommended Seal with Breather and Blocking Tapes
3c
3bSlope
100mm
3a
X 4
6
Installation Type
Back & Side wall
All three sidesBack wall
Go to Installation SequencePage No. 7
Go to Installation Sequence Page No. 10
7
T-Lock
T-Fastener
Wood Screw
Metal Screw
Back & Side wall
Purlin
Purlin
Purlin
Purlin
Purlin
4
5
5c
5b
5a
8
9
9c
9b
9a
6
? ? ? ? ? ?
7
Repeat stages 8-11d
6
8
B
Back & Side wall
9
B
c
B
1918
B
20
20 mm
21
Back & Side wall
Go to Finishing Page No. 14
10
Sheet Installation Sequence
6c
6b
6a
8c
8b
8a
90O
5
6
Cente
r Lin
e
4
T-Lock
T-Fastener
Wood Screw
Metal Screw
Back wall
All three sides
7
8
T-Lock
T-Fastener
11
11
12
12c
12b
12a
10
9
12
Cente
r Lin
e
A
13 14151617 2021
A
Aluminum F-Profile
A
A
A = Max 0.5 Sheet
18 19
A
20 mm
Back wall
Repeat stages 9-12d
Make sure the SUNPAL panel is inserted entirely into the F-Profile, 25mm Min.
Fix the F-Profile to the rafter lateral
side each\every 450mm.
13
150 mm<DimUp to 150 mm
Cente
r Lin
e13
14
151617
By Others By Others
Or
19
A
20 mm
A
A
18
All three sides
20
Repeat stages 9-12d
Left
Right
14
Finishing
Polycarbonate U-Profile 0710
Aluminum Sealing Strip 0610
End-cap for Polycarbonate Joiner
0300
23 X 8
NOTE: Other designated elements like gutters, closures, ridge caps, trimming, flashing etc. are to be specially fabricated according to specific design.
15
20
Aluminum Sealing Strip
24
21
Aluminum S
ealin
g St
rip 22
X 7
In as much as Palram Industries has no control over the use to which others may put the material, it does not guarantee that the same results as those described herein will be obtained. Each user of the material should make his own tests to determine the material’s suitability for his own particular use. Statements concerning possible or suggested uses of the materials described herein are not to be construed as constituting a license under any Palram Industries patent covering such use or as recommendations for use of such materials in the infringement of any patent. Palram Industries or its distributors cannot be held responsible for any losses incurred through incorrect installation of the material. In accordance with our company policy of continual product development you are advised to check with your local Palram Industries supplier to ensure that you have obtained the most up to date information.
05.2019 - XXXXX
©1997 Palram Industries Ltd. | SUNTUF is a registered trademark of Palram Industries Ltd.
PALRAM SA/NT517A Cross keys RoadCavan SA 5094Tel: (08) 8262 2288Fax: (08) 8262 [email protected]
PALRAM NSW/ACTUnit 2, 26 Redfern St, Wetherill Park, NSW 2764Tel: (02) 8788 6100Fax: (02) 8788 [email protected]
PALRAM VIC/TAS34 Buys CourtDerrimut VIC 3030Tel: (03) 9219 4444Fax: (03) 9219 [email protected]
PALRAM QLDUnit 9C / 380 Bilsen RoadGeebung QLD 4034Tel: (07) 3172 5581Fax: (07) 3172 [email protected]
PALRAM WA74 Christable WayLandsdale WA 6065Tel: (08) 9302 4173Fax: (08) 9302 [email protected]