Upload
clifton-cannon
View
213
Download
0
Embed Size (px)
Citation preview
SVX4 chip
4 SVX4 chips hybrid
4 chips hybridSilicon sensors
Front side
Back side
Hybrid data with calibration charge injection for some channels
IEEE Nuclear Science Symposium 2003, Portland, Oregon, U.S.A. Oct. 19-25, 2003
CDF Run IIb Silicon : Stave design and testingRong-Shyang Lu, Academia Sinica, Taiwan
Hybrid electronics
Foam core
Peek Cooling channels 2.9 x 5.6 mm
Silicon Sensors4mm separation
Stave Elements• 1 module = 2 silicon sensors wire bonded and readout by 1 hybrid with 4 SVX4 chips• 3 modules per side• bus cable between silicon and stave core• 1 Mini Port-card per stave• 1 readout unit per stave (3072 channels)
Mechanical Overview• 66 cm long• Carbon fiber composite skins on a foam core• Build-in cooling tube (PEEK)• Kapton bus cables for data and power distribution• 6 silicon sensors glued on top of bus cables, one per side• Hybrids glued and wire bonded on silicon• Readout chips bounded down to bus cable
Mechanical Support• Stave position is registered by pins in two end• The mass of stave results in a sag of 150 m which is within 160 m specification
Finite element analysis of stave structure under gravity
Stave Cooling• Need to operate from -5 C (inner) to 15 C (outer)• 18.3 W heat generated by stave• Build-in U-shaped cooling tube• 0.1 mm wall radiation tolerant polyethylethylketone (PEEK) plastic tube• Assume coolant temp of -15 C, the highest temperature spot is 0 on stave• 43% ethylene glycol by weight in water for operation at -15 C
Stave temperature distribution
Heat Load per stave (W)
SVX4 chips (24) 9.6
Convection 4.2
Mini Port-card 2.5
Leakage current (6 cm) 1.6
Total per stave (W) 18.3
Total Layers 2-5 (W) 3240
Stave Readout Electronics• SVX4 chip
0.25 m CMOS technology 128 parallel charge integration channels low resistivity substrate exploited for ground distribution and digital/analog isolation 128 ADC with real time pedestal subtraction
• Hybrid BeO substrate for low mass and good thermal conductivity 4 gold layers and 100/100 m trace/space and 125 m vias service 4 SVX4 chips to connect to Mini Port-card.
• Mini Port-card BeO substrate as hybrids wing cable connect top and bottom bus cable 5 transceiver chips for bidirectional data control
Stave Material• 1.8% radiation length (X0) for one stave • Smooth material distributions• For whole detector, expect 6% X0 from silicon, carbon fiber and cooling structure; 12% X0 due to additional readout hybrids.
• Single element from 2nd to 6th layers reduce component count reduce fixturing faster construction
• Radiation hard SVX4 readout chips• Low mass, redistribute material optimally• Highly integrated electrical, mechanical, and thermal structure.
active cooling embedded signal and power distribution network 6 modules mounted on stave (3 on each side)
BeO Mini Port-card
Stave Electrical Testing• Pedestal and noise / differential noise (dnoise, i.e. common mode noise suppressed)• Dnoise around 1100 electrons (e-) (depending on setting)• Noise coincide with dnoise which is essential for sparse readout operation• Minimum Ionizing Particle (MIP) signal 22,000 e- (S/N ~ 20)• Best performance when
Al shielding between Si and bus cable properly grounded HV bias return to AGND Al box ground to AGND @ PS
Full stave pedestal distribution
Full stave noise / dnoise distribution
Stave Schedule and Plan• Will build 15 staves in the end of 2003• Sensors are ready; hybrids and Mini Port-cards are in production.• At least 5 staves assembled in barrel with some Layer0 modules• Read out multiple staves and study performance
Laser signal with Offline Pedestal Subtraction
Stave Data of Laser Run• Shine laser light on silicon of a stave• Clear and clean laser signal after pedestal subtraction
Chip/Hybrid/Module Testing• Study the performance of all chips / hybrids / modules• Test the components and perform burn-in before module / stave assembling.
Pedestal vs channels for SVX4 chip
SVXIIb Detector Barrel Layout
Side view
Layer 0: 12 fold AxialLayer 1: 6 fold Axial-AxialLayer 2: 12 fold Axial-SAS(1.2)Layer 3: 18 fold SAS(1.2)-AxialLayer 4: 24 fold SAS(1.2)-AxialLayer 5: 30 fold Axial-Axial
Sensors
Hybrids
Stave Design
• Single-sided silicon sensor 320m thickness and 75m pitch for Axial (80m stereo) depletion voltage >100V and <200V
• Hybrids and Mini Port-card used to readout signal• Complies with deadtime-less operation of readout electronics
A module = 1 hybrid + 2 Si
1,100 e- noise
Bow-shaped problem corrected on the new SVX4 chip version
Optimized chip setting
Noise vs channels for SVX4 chip
Capacitance load
Noise vs channels for SVX4 chip
0 pF
10 pF
20 pF