TABLE OF CONTENTS - neptuneenergy.com · Following Buyer’s general specifications, latest edition, shall be adhered to wholly, where applicable. 4.1 GENERAL Index Offshore Installation

Neptune Energy Netherlands B.V.

Specification 104 rev. 5 Page 2 of 9

TABLE OF CONTENTS

1.0 SCOPE ............................................................................................................................................... 3

2.0 MANDATORY RULES AND REFERENCE DOCUMENTS .............................................................. 4

3.0 LIST OF MANDATORY EU-DIRECTIVES ....................................................................................... 5

3.1 LIST OF MANDATORY NATIONAL RULES, LAWS AND REGULATIONS FOR THE

NETHERLANDS ................................................................................................................................................ 5

4.0 LIST OF MANDATORY NEPTUNE ENERGY NEDERLAND SPECIFICATIONS ........................... 6

4.1 GENERAL ........................................................................................................................................................... 6 4.2 GUIDELINES ...................................................................................................................................................... 6 4.3 100 – ENGINEERING SPECIFICATIONS .................................................................................................. 6 4.4 200 – STRUCTURAL SPECIFICATIONS .................................................................................................... 6 4.5 400 – EQUIPMENT SPECIFICATIONS ...................................................................................................... 6 4.6 500 – PIPING SPECIFICATIONS ................................................................................................................. 7 4.7 600 – ELECTRICAL SPECIFICATIONS ....................................................................................................... 7 4.8 700 – INSTRUMENTATION SPECIFICATIONS ...................................................................................... 7

5.0 LIST OF ABBREVIATIONS............................................................................................................... 8

6.0 NOTIFIED BODIES AND EXPERT ORGANISATIONS ................................................................... 9

7.0 LIST OF STANDARDS AND CODES ............................................................................................... 9



1.0 SCOPE

The facility shall be designed, constructed, certified, and installed in accordance with current

mandatory rules and reference documents. Mandatory legalized rules and reference documents

are forced laws and regulations applicable for the Netherlands and Dutch Continental Shelf,

Buyer’s specifications, agreed design codes and EU-harmonized technical standards. (see also

Table 1).



2.0 MANDATORY RULES AND REFERENCE DOCUMENTS

The reference documents indicated as “Mandatory legalized” in Table 1 shall be used by the

Supplier.

In case where no “Mandatory legalized” documents oblige, Supplier shall use reference

documents indicated as “Accepted codes and standards” in Table 1.

Supplier shall use the following terms of reference:

Where requirements in reference documents deviate from each other, the content of the

applicable Buyer’s Specification will prevail;

In circumstances where Buyer’s Specifications deviate from legal rules the contractor shall notify

Buyer;

The Supplier shall use the reference documents as stated in this specification. AII work and

equipment specified shall confirm in design, material and performance with the latest editions

(including amendments).

Terms such as "usually", "preferably", “preferably”, "most common" and "most desirable"

occurring in design codes and standards are to be construed as "shall be" for this Basic Report.

The order of precedence of requirements of work or equipment shall be according Table 1)

Man

dato

ry leg

alize

d

1. Directives from the European Union (EU-directives) (and guidelines)

2. Mining Law and ARBO Law (and amendments)

3. Governmental rules and resolutions (Netherlands)

4. Requirements as described in the Project Specifications

5. Buyer’s General Specifications

6. (Harmonised) European Standards (EN-standards by CEN or

CENELEC)

Acc

ep

ted

co

des

an

d

stan

dard

s (

best

acc

ep

ted

pra

ctic

es)

7. International agreements and conventions (SOLAS, IMCO, ITU,

CCITT)

8. International standards (ISO- and IEC-)

9. National standards (NEN-, NPR-, NTA-, BS-)

10. Design Codes (ASTM-, API-, NFPA-, ASME-)

11. Practical and technical recommendations & guidelines (TR-, TS-,

IALA-, Noble Denton-, EEMUA-, DNV-, AISC-, PGS-, AGMA, CAP,

etc.)

Table 1 : Order of precedence of requirements

NOTE:

Some standards consist of more parts. In the listing in the appendix mentioned in chapter 7.0

this is indicated with “(All Parts)”. In case the specified standard is an umbrella standard, Supplier

shall use all standards, which are specified in this umbrella standard. (examples of umbrella

standards are e.g. EN 13480, EN 13455, EN 19252).



3.0 LIST OF MANDATORY EU-DIRECTIVES

Machinery Directive 2006/42/EG

Pressure Equipment Directive 2014/68/EU

ATEX Directive 2014/34/EU

Safety & Health Signs Directive 92/58/EEG

Arbeidsmiddelen 2009/104/EG

Low voltage Directive 2014/35/EU

Electromagnetic Compatibility Directive 2014/30/EU

Telecommunications Terminal Equipment Directive 98/13/EC

Radio and Telecommunications Terminal Equipment Directive 99/5/EC

Marine Equipment Directive 2014/90/EU

ARBO Wet 89/391/EEG

Besluit emissie-eisen middelgrote stookinstallatie (88/609/EEG)

3.1 LIST OF MANDATORY NATIONAL RULES, LAWS AND REGULATIONS FOR THE NETHERLANDS

Mijnbouwwet Staatsblad 554, 1 Januari 2017

Mijnbouwbesluit Staatsblad 556, 01 Juli 2017

Nota van Toelichting Mijnbouwbesluit Staatsblad 556, 01 Juli 2017

Inwerktreding Mijnbouwbesluit Staatsblad 603, 6 December 2002

Wijziging Mijnbouwbesluit Staatsblad 89, 6 Maart 2017

Mijnbouwregeling 01 Januari 2018

Nota van toelichting Mijnbouwregeling Staatscourant 16804, 15 September 2011

Besluit algemene regels milieu mijnbouw Staatsblad 114, 27 Maart 2017

Regeling algemene regels milieu mijnbouw Staatsblad 91, 3 April 2008

Arbeidsomstandighedenwet Staatsblad 22, 08 Februari 2017

Arbeidsomstandighedenbesluit Staatsblad 225, 19 juni 2017

Arbeidsomstandighedenregeling Staatscourant. Suppl. 7530, 16 Februari 2016

Wijziging Arbeidsomstandighedenregeling Staatsblad 340, 29 september 2016

Warenwetbesluit drukapparatuur Staatsblad 229, 22 Juni 2016

Besluit Drukapparatuur Staatsblad 311, 5 juli 1999

Wijzigingsbesluit Besluit Drukapparatuur Staatsblad 339, 5 juli 2001

Ministeriele regeling drukapparatuur Staatsblad 224, 19 november 2001

Wijziging Warenwetbesluit drukapparatuur Staatblad 387, 22 juli 2004

Ministeriele regeling inspectie scheepvaart Staatsblad 1939 10october 2010



4.0 LIST OF MANDATORY NEPTUNE ENERGY NEDERLAND SPECIFICATIONS

Following Buyer’s general specifications, latest edition, shall be adhered to wholly, where

applicable.

4.1 GENERAL

Index Offshore Installation plan

Standard Drawing Weight Control, Rev. 1

Standard Drawing GE-32-0001 – Earth Boss Detail, Rev. 0

Standard Drawing GE-33-0001 – Mounting Boss Detail, Rev. 0

SP-50007 Typical Manual Louver, Rev. 0

Standard Drawing GE-40-0001 –Nozzle Loads for Mechanical Equipment – ANSI flanges of

150 lb rating, Rev. 0







Standard Drawing GE-40-0005–Nozzle Loads for Mechanical Equipment– ANSI flanges of


Standard Drawing GE-40-0006–Nozzle Loads for Mechanical Equipment– ANSI flanges of


4.2 GUIDELINES

En.zm.00.03 Guideline Lifting Provisions

4.3 100 – ENGINEERING SPECIFICATIONS

Specification 101 Administration of Drawings - Drawing Control

Specification 102 Production of documents

Specification 103 Supplier Document Requirements

Specification 104 Laws, Regulations, Codes and Standards

4.4 200 – STRUCTURAL SPECIFICATIONS

Specification 201 Supply and Fabrication of Steel Structures

Specification 205 Architectural Requirements

4.5 400 – EQUIPMENT SPECIFICATIONS

Specification 401 Unfired Pressure Vessel

Specification 407 Air Cooled Heat Exchanger.

Specification 419 Storage Tanks

Specification 452 Positive Displacement Pump

Specification 457 Horizontal Centrifugal Pump

Specification 458 Vertical Inline Centrifugal Pump



4.6 500 – PIPING SPECIFICATIONS

Specification 501 Piping Design

Specification 502 Piping Fabrication and Pressure Testing

Specification 503 Pipe Fittings and Valves

Specification 503 Summary sheets

Specification 504 Standard Pipe Supports

Specification 505 Dimensional Drawings for Specification 503

Specification 506 Guideline Maintenance work and changes offshore installations

Specification 518 Insulation of Piping and Equipment

Specification 524 Coating Threaded Fasteners

Specification 525 Painting and Coating

Specification 541 General Construction of HVAC Installations

Specification 580 Pipelines Welding and NDT Testing

4.7 600 – ELECTRICAL SPECIFICATIONS

Specification 610 General Construction of Electrical, Instrumentation and

Telecommunication Installations

Specification 611 Fabrication, Assembly, Cabling termination, Earthing and Testing of

Electrical, Instrumentation Panels and Cabinets

Specification 612 Testing, Pre-commissioning & Commissioning

Specification 613 Electrical & Instrumentation – General Details and Hook-ups

4.8 700 – INSTRUMENTATION SPECIFICATIONS

Specification 713 Air Operated Valve Actuator

Specification 714 Hydraulic Operated Valve Actuator

Specification 715 Electric Motor Operated Valve Actuator

http://www.gdfsuezep.nl/fileadmin/user_upload/Documenten/PDF/E_P/specification_713_rev_1263826632._6__air_operated_valve_actuator.pdf

http://www.gdfsuezep.nl/fileadmin/user_upload/Documenten/PDF/E_P/specification_714_rev_1263826650._1__hydraulic_operated_valve_actuator.pdf



5.0 LIST OF ABBREVIATIONS

AIA Aerospace Industries Association

AISC American Institute of Steel Construction

AGMA American Gear Manufactures Association

ANSI Association American National Standards

API American Petroleum Institute

ASHRAE American Society of Heating, Refrigeration, and Air-conditioning

Engineers

BV Bureau Veritas

CAA Civil Aviation Authority

CAP Civil Aviation Publication

CCITT Consultative Committee International Telegraph and Telephone

CCIR Consultative Committee International Radio

CODAP French Code for the Construction of Unfired Pressure Vessels

DNV Det Norske Veritas

EEMUA Engineering Equipment and Materials Users Association,

HSE Health and Safety Executive

IEEE Institute of Electrical & Electronic engineers

ICAO International Civil Aviation Organization

IMO International Maritime Organization

IMCO Intergovernmental Maritime Consultative Organization

ITU International Telecommunication Union

ISA Instrument Society of America,

ISO International Standard Organisation

ISSO Instituut voor Studie en Stimulering van Onderzoek

LSA Life Safety Appliances (Amendment SOLAS)

MODU Mobile Offshore Drilling Units

NAS National Aerospace Standard

NFPA National Fire Protection Association

NOBLE DENTON Private Company Noble Denton Marine Services

NFPA National Fire Protection Association

OCMA Oil Companies Material Association

RTOD Regels voor Toestellen Onder Druk

RP Recommended Practice

SOLAS Safety of Life at Sea Convention

STEK Stichting Erkenningsregeling voor de Uitoefening van het

Koeltechnisch Installatiebedrijf

TEMA Standard of the Tubular Exchanger Manufacturers Association



6.0 NOTIFIED BODIES AND EXPERT ORGANISATIONS

Notified bodies are third party organizations for CE-marking on products. These third part

organizations have been appointed by a member of the EER as a competent authority following

completion of a conformity assessment, verification and qualification process.

Supplier shall contract a notified body. This notified body shall be the Expert Organization to

ensure that the facility, products and its components comply with the all the requirements of

the applicable EU-directive and harmonized standards as specified in Buyer’s general

specifications. Supplier shall ensure that the essential safety requirements of all the applicable

EU-directives and requirements of the Dutch Law and regulations shall be met. Supplier shall

deliver with the product, equipment or installation a Declaration of Conformity Certificate with

the applicable EU-directives, codes and standards stated.

Note:

For pressure equipment it is not allowed to use design codes which are not harmonized within the

European Union member states without a written approval of Buyer or stated within the applicable

Buyer’s applicable Specification. (Examples of rejected design codes by Buyer are AD-Merkblätter,

CODAP, RTOD or ASME).

7.0 LIST OF STANDARDS AND CODES

Appendix 1 gives the list of the applicable codes and standards supplier is required to follow

for respective equipment/package.

CODE

NUMBER

TITLE OF CODE /

STANDARD

DESCRIPTION OF THE CODE / STANDARD

Ex

pir

y d

ate

REM

AR

KS

Netherlands

ST.01.0 AISC Specification for structural steel buildings, allowable design and plastic design, 9th edition 2016

ST.02.0 API, RP, 2A-WSD Recommended Practice for Planning, Designing and Constructing Fixed Offshore Platforms- Allowable Design and Plastic Design, 21st

edition, American Petroleum Institute2014

ST.03.0 AWS D1.1 (All Parts Structural welding code, American Welding Society 2015

ST.04.0 BV, NR423 DTO ROOE Bureau Veritas, Recommanded Practice NR423 DTO ROOE, Corrosion Protection of steel Offshore Units and Installations, 2006

ST.05.0 DNV Classification note 30.5 Environmental Conditions and Environmental Loads, 2000

ST.06.0 DNV, RP B401 DNV Recommanded Practice RP B401 Cathodic Protection Design, Det Norske Veritas Industry AS, Hovik, 2017

ST.07.0 DNV-RP-C204 Design against accidental loads, Amended 2017

ST.08.0 EEMUA publication no. 158 EEMUA Publication Construction Specification for Fixed Offshore Structures in the North Sea no.158, 2014

ST.09.0 IALA 0-139 (International Association of lighthouse Authorities) Recommendation on The Marking of Man-made Offshore Structures, 1st edition, 2014

ST.10.0 IALA Naviguide (International Association of lighthouse Authorities) Aids to Navigation Guide, 2014

ST.11.0 HSE, OTO,/015 Offshore Technology Report OTR/015 Steel, ISBN 0 71762391 2001/2015

ST.12.0 HSE, OTO,/016 Offshore Technology Report OTR/016 Sleeve Connections, ISBN 0 7176 2390 2001/2016

St.13.0 Noble Denton 0013/ND Guidelines for Load-outs, Rev 8, 2015

ST.14.0 Noble Denton 0027/ND Guidelines for Marine Lifting Operations, Rev 11, 2015

ST.15.0 Noble Denton 0028/ND General Guidelines for the Transportation and Installation of Steel Jackets, Rev 6, 2015

ST.16.0 Noble Denton 0030/ND General Guidelines for Marine Transportations, Rev 6, 2015

ST.18.0 AISC Manual of Steel Construction - Allowable Stress Design 1989

ST.19.0 API RP 11S Recommended Practice for ESP Installations 1994

ST.20.0 ISO 19902 Fixst steel offshore structurals 2007

ST.21.0 ISO 19901 Specific requirements for offshore structurals part 1 meteo seon design at operating conditions 2015

ST.22.0 ISO13633 systemen voor vluchtdeursluitingen voor het gebruik bij vluchtroutes - Eisen en beproevingsmethoden 2009

ST.23.0 ISO13633 systemen voor vluchtdeursluitingen voor het gebruik bij vluchtroutes - Eisen en beproevingsmethoden 2009

HELICOPTER

H.01.0 ICAO annex 14 volume II Heliports 2015

H.02.0 CAO DOC 9261-AN/903:; RGS

WG/4-WP/17

Heliport Manual2017

SPECIFICATION 104 - LAWS, REGULATIONS, CODES AND STANDARDS - APPENDIX-1

STRUCTURAL

Page 1 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


H.03.0 Cap 437' RGS WG/4-WP/1 Offshore Helicopter Landing Areas - Guidance on standards, Civil Aviation Authority Publication. 6th edition, ISBN 978 0 11792 1692017

H.04.0 Richtlijn Bedrijfsgebonden

Helihavens

Richtlijn Helivaart van het Misterie Verkeer en Waterstaat Divisie Luchtvaart,(Staatscourant nr 16336)Richtlijn Helivaart van het Misterie

Verkeer en Waterstaat Divisie Luchtvaart,(Staatscourant nr 16336)2007

H.05.0 NFPA 418 Heliports 2016

H.06.0 Mijnbouw Regeling [MR] Wet

245,

Chapter 4 Helicopter decks

MECHANICAL EQUIPMENT - TANKS, VESSELS HEATERS AND HEAT EXCHANGERS

PV.01.0 ANSI A58.1 Wind loads, 1982

PV.02.0 API 12J Specification for oil and Gas Separators, 2009API 12

PV.03.0 API 560 Data Sheets - Data Sheets for Fired Heathers for General Refinery Services, 2016

PV.04.0 API 660 Shell and tube Heat Exchanges, 2015

PV.05.0 API 2000 Venting atmosphere and pressure storage tank, + errata 1998

PV.06.0 EN 12952 (All Parts) Water-tube boilers and auxiliary installations 12952

PV.07.0 EN 13445 (All Parts) Unfired Pressure Vessels 13445 (All

PV.08.0 PED 2014/68/EU Pressure Equipment Directive 2014

PV.09.0 API 671 (EN-ISO 10441) Special Purpose couplings for Petroleum, Chemical and Gas Industry Services 2007

PV.10.0 Stoomwezen Dutch Rules for Pressure Vessels 2007

PV.11.0 ISO15547 Plate-type heat exchangers -- Part 1: Plate-and-frame heat exchangers 2005

PIPING AND FITTINGS

PF.01.0 API 594 Check valves: water, water-Lug and double flanged type, 2017

PF.02.0 API 598 Valve inspection and testing, 2016

PF.03.0 API 5L Specification for line pipe, 2013

PF.04.0 API 600 (All Parts): Bolted bonnet steel gate valves for petroleum and natural gas industries, 2015

PF.05.0 API 602 Compact steel gate valves-flanged, threaded, welding and extended-body ends, 2015

PF.06.0 API 607 Fire Test for soft seated quarter-turn valves, 2010

PF.07.0 API 609 Butterfly valves: double flanged, lug- and water-type, 2016

PF.08.0 API 6D Specification for Pipeline Valves + errata 2014

PF.09.0 API 6FA Specification for fire test for valves, errata 2008

PF.10.0 API RP 14C Recommended practice for analysis, design, installation and testing of basic surface safety systems for offshore production platforms, 2001

PF.11.0 API RP 14D Specification for wellhead surface valves for the offshore service, 1994

Page 2 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


PF.12.0 API RP 14E:R Recommended practice for design and instalation of offshore production platform piping systems, 2013

PF.12.5 ASME B1.20.1 Pipe threads general purpose 2013

PF.12.6 ASME B16.5 Pipe flanges and fittings 2017

PF.13.0 ASME B16.10 Face-to-face and end-to-end dimensions of valves 2017

PF.14.0 ASME B16.11 Forged fittings, socket-welding and threaded 2016

PF.15.0 ASME B16.20 Metallic gaskets for pipe flanges 2012

PF.16.0 ASME B16.21 Nonmetallic flat gaskets for pipe flanges 2016

PF.17.0 ASME B16.25 Butt-welding ends 2012

PF.18.0 ASME B16.3 Valves - flanged, threated and welding ends 2013

PF.19.0 ASME B16.4 Large diameter steel flanges 2017

PF.20.0 ASME B16.48 Steel line blanks 2017

PF.21.0 ASME B16.5 Pipe flanges and flanged fittings 2017

PF.22.0 ASME B16.9 Factory-made wrought butt-welding fittings 2012

PF.23.0 ASME B18.2.1 Square and hex bold and screws 2012

PF.24.0 ASME B18.2.2 Square and hex nuts 2015

PF.25.0 ASME B31.3 Process piping 2016

PF.26.0 ASME B31.4: Pipeline transportation systems for liquid hydrocarbons and others liquids 2016

PF.27.0 ASME B31.8 Gas transmission and distribution piping systems 2016

PF.28.0 ASME B36.10 Welded and seamless wrought steel pipe 2004

PF.29.0 ASME B36.19 (R2015) Stainless steel pipe 2004

PF.30.0 ASME II Materials 2017

PF.31.0 ASME V Nondestructive examination 2017

PF.32.0 ASME VIII-1 Rules for construction of pressure vessels - Division 1 2017

PF.33.0 ASME VIII-2 Rules for construction of pressure vessels - Division 2 Alternative rules 2017

PF.34.0 ASME IX Welding & Brazing Qualifications 2017

PF.35.0 BS 18681975+A1 Steel check valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied industries 1990

PF.36.0 EN-BS 1873+A1 Steel globe and globe stop and check valves (flanged and butt-welding ends) for the petroleum, petrochemical and allied industries2016

PF.37.0 BS 5351; EN-ISO 17292 Steel ball valves for the petroleum, petrochemical and allied industries 2015

PF.38.0 BS 5352; EN-ISO 15761 Steel wedge gate, globe and check valves 50mm and smaller for the petroleum, petrochemical and allied industries 2002

PF.39.0 EN-ISO 12266-1; EN-ISO 12266-2 Testing of valves - Part 1: Specification for production pressure testing requirements2002/2003

PF.40.0 EN-ISO 10497 Testing of valves - Part 2: Specification for the fire type-testing requirements 2004

Page 3 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


PF.41.0 EEMUA 234 90/10 Copper Nickel Alloy Piping for Offshore Applications - Specification: Tubes Seamless and Welded, 2015

PF.42.0 EEMUA 234 90/10 Copper Nickel Alloy Piping for Offshore Applications - Specification: Flanges Composite and Solid, 2015

PF.43.0 EEMUA 234 90/10 Copper Nickel Alloy Piping for Offshore Applications - Specification: Fittings, 2015

PF.44.0 EN-ISO 9606(All Parts) Qualification test of welders - Fusion welding - Part 1: Steels, 2004 + addendums 2017

PF.45.0 EN ISO 9712 Non Destructive testing - Qualification and certification of NDT personnel - General principles, 2012

PF.46.0 EN 1779+add Non-destructive testing - leak testing - criteria for method and technique selection, + addendum 1999/2003

PF.47.0 EN 10021 General technical delivery requirements for steel and iron products, 2006

PF.48.0 EN 10025 (All Parts) Material: Hot-rolled products of structural steels 2004

PF.49.0 EN 10028 (All Parts) Material: Flat products made of steels for pressure purposes 2003

PF.50.0 EN 10225 Weldable Structural Steel for Fixed Offshore Structures. Technical Delivery Conditions, 2009

PF.51.0 EN 12732 Gas supply systems - Welding steel pipe work -Functional requirements 2014

PF.52.0 EN 13184 Non-destructive testing - leak testing - pressure change method, 2001

PF.53.0 EN 13815 Non-destructive testing - leak testing - tracer gas method, 2006

PF.54.0 EN 13480 (All Parts) Metallic industrial piping - Part 1: General metallic materials 2012

PF.55.0 EN-ISO 5817 Welding - fusion - welded joints in steel, nickel titanium and their allows - Quality levels for imperfections 2014

PF.56.0 EN-ISO 15607 Specification and qualification of welding procedures for 2003

PF.57.0 EN-ISO 15614 (All Parts) Specification and qualification of welding procedures for metallic materials - Welding procedure test 2017

PF.58.0 EN-ISO 9606(All Parts) Qualification test of welders - Fusion welding - Part 1: Steels, addendums 2017

PF.59.0 MSS SP-25 Standard marking system for valves, fittings, flanges, and unions, 2013

PF.60.0 API 5CT Specification for Casing and Tubing 2011

PF.61.0 API 6D Specification for pipe-line valves (Gate, Plug, Ball and Check Valves) 2014

PF.62.0 API 14A Specification for Subsurface Safety Valve Equipment. 2015

PF.63.0 NACE MR-01-75 /ISO 15156-1 Sulphide Stress Cracking Resistant Metallic Materials for Oil Field Equipment. 2001

PF.64.0 DIN EN 10204 Material Testing 2005

PF.65.0 EN ISO: 21457 Material selection and corrosion control for oil and gas production platforms 2010

PF.66.0 EN 50504 Validation off arcwelding equipment 2008

PF.67.0 EN 17662 Welding calibration validation verification off welding equipment 2016

COATING FOR STEEL AND PIPING

CP.01.0 EN-ISO 1461 Hot-dipperd galvanised coatings on fabricated iron and steel articles, 2009

CP.02.0 ISO 4624 Paints and varnishes - Pull-off test for adhesion, 2016

CP.03.0 ISO 12944 (All Parts) Paints and varnishes - corrosion protection of steel structures by protective paint systems, All Parts 2018

Page 4 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


CP.04.0 ISO12736 Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures 2014

CRANESC.01.0 EN 13852-1 Offshore cranes part 1: General Directives, 2013

C.02.0 EN 13000+A1 Cranes General Directives, 2014

C.03.0 EN 13000+A1 Cranes Loads and Load Combinations, + addendum 2014

C.04.0 EN 13000+A1 Cranes Steel Structures, + addendums 2014

C.05.0 EN 13000+A1 Cranes Mechanical Equipment + addendum 2014

C.06.0 EN 13000+A1 Cranes Electrical Equipment, + addendum 2014

C.07.0 EN 13000+A1 Cranes Stability, 2014

C.08.0 EN 13000+A1 Cranes Structural Requirements Regarding Safety, 2014

C.09.0 EN 13000+A1 Cranes, Documents, Testing, Operation and Maintenance, 2014

C.10.0 EN 13000+A1 Cranes- Automatic Limiting Decives, + addendum 2014

C.11.0 Platform Crane Lloyd's register pf shipping offshore cranes, version 2013

C12.0 EN 13000 Cranes Steel Structures 2010/2014

C.13.0 EN 13001-1 Hijskranen-Algemeen ontwerp-Deel 1:Algemene grondslagen an eisen 2015

C.14.0 LRS MOU Rules and regulations 2017

MACHINERY AND ROTATING EQUIPMENT

M.01.0 AGMA 420 (All Parts) Standard Gear Reducer 2003

M.02.0 AGMA 421 (All Parts) High Speed Gear Reducer 1969

M.02.5 AGMA 6010-E88 Standard for Spur, Helical, Herrigebone and Bevel Enclosed Drives

M.03.0 API RP 11S3 Electric Submersible Pump Installations, 2013

M.04.0 ISO 13709 Centrifugal Pumps for Petroleum, Petrochemical and natural gas industrie 2009

M.05.0 API 613 Special Purpose Gear Units for Petroleum, Petrochemical and Gas Industry Services, 2003

M.06.0 API 614 Lubrication Shaft-Sealing and Control-Oil Systems for Special-Purpose Applications, 2008

M.07.0 API 616 Gas Turbines for Petroleum, Chemical and Gas Industry Services, 2011

M.08.0 API 617 Axial and Centrifugal Compressors and Expandr-compressors for Petroleum, Chemical and Gas Industry Services, 2014

M.09.0 API 618 Reciprocating Compressors for Petroleum, Chemical and Gas Industry Services, 2007

M.10.0 API 675 Datasheet - Postive Displacement Pumps, 2015

M.10.1 API 676 Positive Displacement Pumps - Rotary, 2015

M.11.0 EN-ISO13849-2 Safety of machinery - Safety-related parts of control systems- Part 1: General Principles for design, 2012

Page 5 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


M.12.0 EN 1834-1 Reciprocating internal combustion engines - Safety requirements for design and construction of engines for use in potentially explosive

atmospheres - Part 1: Group II engines for use in flammable gas and vapour atmospheres,2000

M.12.4 EN-ISO 3744 Acoustics - Determination of sound power levels of noise Sources using sound pressure - Engineering method in an essentially free field

over a reflecting plane, 2010

M.12.6 EN-ISO 9906 Rotodynamic pumps, Hydraulic performance acceptance tests, 2012

M.13.0 ISO 3046 (All Parts) Reciprocating internal combustion engines - Performance, All Parts 2009

M.13.5 ISO 10816-1+C238 Mechanical Vibration, Evaluation of machine vibration by measurement on non rotating parts - General guidelines, 2016

M.14.0 ISO/TS 7849 Akoestiek - Bepaling van het niveau van de sterkte van het lichtgeluid uitgestraald door de machines door meting van trillingen

Deel 1: Bepalingsmethode die gebruik maakt van een vaste stralingsfactorAkoestiek - Bepaling van het niveau van de sterkte van het

lichtgeluid uitgestraald door de machines door meting van trillingen

2009

M.16.0 Directive 2006/42/EC European Machinery Directive 2006

M.17.0 MD Directive 98/37/EC Machinery Directive 2006

M.18.0 DIN 24273:01 Acceptance test for Centrifugal Pumps 1998

M.19.0 ISO 1940-1: Mechanical Vibration - Balance Quality Requirement of Rigid Rotors 2003

M.20.0 BS 1133-8+A1 Mechanical aids in package handling 2011

M.21.0 ISO 9906 Code for acceptance tests, part 1 2012

M.22.0 EN-ISO 281 Rolling Bearings - Dynamic Load Ratings and Rating Life 2007

M.23.0 ISO 8372 Mechanical Vibrations of machinery having a rotation frequency in range between 10 S-1 and 200 S-1. 1987

M.24.0 ISO 5199 Horizontal Centrifugal Pumps 2002

M.25.0 API 682 Shaft Sealing Systems for centrifugal and rotary pumps 2014

M.26.0 EN 15259 Air quality measurements (Emissions NOX) 2007

M.27.0 ISO15544 Offshore production installations -- Requirements and guidelines for emergency response 2000

M.28.0 ISO13631 Packaged reciprocating gas compressors 2002

ELECTRICAL

E.01.0 API RP 14 F Recommended practice for design and installation of electrical systems on offshore platform, 2008

E.02.0 EN 1838 Lighting applications - Emergency lighting, 2013

E.03.0 EN 50347 General purpose 3 phaseinduction motors having standard dimensions and output- Frame numbers 56 to 315 and flange 65 to 740,2001

E.04.0 EN-IEC 61000-6-3 Electromagnetic compatibility (EMC) - Part 6-3: Generic Standards - Emission standard for residential, commercial and light-industrial

environments 2007

E.04.0 EN-IEC 61000-6-3/A1 Electromagnetic compatibility (EMC) - Part 6-3: Generic standards - Emission standard for residential, commercial and light-industrial

environments 2011

E.04.0 EN-IEC 61000-6-2 Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial environments 2005

Page 6 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


E.04.0 EN-IEC 61000-6-2/C11 Electromagnetic compatibility (EMC) - Part 6-2: Generic standards - Immunity for industrial environments 2005

E.05.0 EN 50110 (All Parts) Operation of electrical installations, All Parts 2013

E.06.0 EN 50171 Emergency lighting system - central power supply systems, 2001

E.06.0 EN 50171 Ontw. Central safety power supply systems, 2013

E.07.0 EN 50172 Emergency escape lighting systems, 2004

E.08.0 EN 50178 Electronic equipment for use in power installations, 19978

E.08.5 EN 50209 Test of insulation bars and coils of high-voltage machines, 1998

E.09.0 EN 50272-2 Safety requirements for secondary Battery and Battery installatiobns - Part 2: Stationary Batteries, 2001

E.10.0 EN 55011 Industrial, scientific and medical equipment - Radio-frequency disturbance characteristics - Limits and methods of measurement 2016

E.11.0 EN 55014 (All Parts) Limits and methods of measurement of Radio interference characteristics of household electrical appliances, portable tools and similiar

electric apparatus. All Parts2017

E.11.1 EN 55015 Limits and methods of measurement of radio disturbance characteristics of electrical lightning and simular equipment, 2016

E.11.1 EN 55015 Limits and methods of measurement of radio disturbance characteristics of electrical lighting and similar equipment, 2013

E.11.2 EN 55016 (All Parts) Specification for radio disturbance and immunity measuring apparatus and methods, All Parts 2011

E.11.8 EN 55020 Sound and television broadcast receivers and associated equipment - Immunity characteristics - Limits and methods of measurement, 2007

E.13.0 EN 61000 (All Parts) Electromagnetic Compability, All Parts indices of solid insulating materials 2007

E.14.0 EN-IEC 60034 (All Parts) Rotating electrical machines, All Parts 1-30 2017

E.15.0 EN-IEC 60051 (All Parts) Direct acting indicating analogue electrical measuring instruments and their accessories, All parts 2016/2017

E.16.0 EN-IEC 60072 (All Parts) Dimensions and output series for rotating electrical machines 1991-2014

E.17.0 EN-IEC 60079 (All Parts) Explosive atmospheres 2006-2018

E.18.0 EN-IEC 60079-0 Explosive atmosphere - Part 0: Equipment General requirements, 2017

E.18.1 EN-IEC 60079-10 Explosive atmosphere-part 10: Classification of Areas - Explosive Gas Atmospheres, 2015

E.18.2 EN-IEC 60079-14 Explosive atmosphere-part 14: Electrical installations design, selection and erection, 2014

E.18.3 EN-IEC 60079-17 Explosive atmosphere-part 17: Electrical installations Inspection and maintenance, 2014

E.18.4 EN-IEC 60079-1 Explosive atmospheres – Part 1: Equipment protection by flameproof enclosures “d” 2014

E.18.5 EN-IEC 60079-2 Explosive atmospheres – Part 2: Equipment protection by pressurizing enclosures “p” 2014

E.18.6 EN-IEC 60079-5 Explosive atmospheres – Part 5: Equipment protection by powder filling “q” 2015

E.18.7 EN-IEC 60079-6 Explosive atmospheres – Part 6: Equipment protection by oil immersion “o” 2015

E.18.8 EN-IEC 60079-7 Explosive atmospheres – Part 7: Equipment protection by increased safety “e” 2015

E.18.9 EN-IEC 60079-11 Explosive atmospheres – Part 11: Equipment protection by intrinsic safety “i” 2011

E.18.10 EN-IEC 60079-18 Explosive atmospheres – Part 18: Equipment protection by encapsulation “m” 2014

E.18.11 EN-IEC 60079-25+C11 Explosive atmospheres – Part 25: Intrinsically safe systems 2010

E.19.0 EN-IEC 60085 Electrical insulation - Thermal evaluation and designation, Electrical insulation - Thermal evaluation and designation, 2007

Page 7 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


E.20.0 EN-IEC 60092 (All Parts) Electrical Installations in Ships 2018

E.21.0 EN-IEC 60146 (All Parts) Semi-conductor converters 2010

E.22.0 EN-IEC 60204 (All Parts) Safety of machinery- Electrical equipment of machines 2018

E.23.0 EN-IEC 60255 (All Parts) Electrical relays 2018

E.24.0 EN-IEC 60269 (All Parts) Low Voltage fuses 2013

E.25.0 EN-IEC 60332 (All Parts) Test on electric cables under fire conditions, All Parts 2005

E.26.0 EN-IEC 60439 (All Parts) Low voltage switch gear and control qear assemblies, All Parts 1979

E.27.0 EN-IEC 60529 Degrees of protection provided by enclosures, 2004

E.27.0 EN-IEC 60529/A2 Degrees of protection provided by enclosures (IP Code), 2013

E.28.0 EN-IEC 60623 Secondary cells and batteries containing alkaline or other non-acid electrolytes- Vented nickel cadmium prismatic rechargeable single

cells, 2017

E.29.0 EN-IEC 60896 (All Parts) Stationary lead-acid batteries 2004

E.30.0 EN-IEC 60909 (All Parts) Short circuit current calculations in three-phase AC systems 2016

E.31.0 EN-IEC 60947 Low Voltage Switch gear and Control gear 2017

E.31.4 EN-IEC 61439-1 Low Voltage Switch gear and Control gear Assemblies - Part 1 General rules, 2011

E.32.0 EN-IEC 61537 Cable management - Cable tray systems and cable ladder systems, 2011

E.33.0 EN-IEC 61800 * (All Parts) EMC requirements for power drive systems 2015

E.34.0 EN-IEC 62040-1 Uninterruptible power systems (UPS) Part 1: General and Safety Requirements for UPS used in operator access areas, 2017

E.35.0 EN-IEC 62040-3 Uninterruptible power systems (UPS) Part 3: methods of specifying the performance and test Requirements, 2011

E.36.0 EN-IEC 62305 * (All Parts) Lighting Protection 2013

E.37.0 EN-IEC 62271-200 High voltage switch gear and control gear - Part 200: AC metal enclosed switchgear and controlgear for rated voltages above 1KV and

up to and including 25KV, 2011

E.37.0 EN-IEC 62271-200 High-voltage switchgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up

to and including 52 kV, 2011

E.37.0 EN-IEC 62271-200/C1 High-voltage swithgear and controlgear - Part 200: AC metal-enclosed switchgear and controlgear for rated voltages above 1 kV and up

to and including 52 kV, 2015

E.38.0 EN-IEC 60038 CENELEC standard voltages, 2009

E.39.0 EN-IEC 60044 (All Parts) Instrument transformers 1996-2004

EN-IEC 60050 (All Parts) International Electro Technical Vocabulary 2015

E.40.0 EN-IEC 60059 /A1 IEC Standard current ratings, 2009

E.41.0 EN-IEC 60112 Method for the determination of the proof and the comparative tracking indices of solid insulating materials 2003

E.41.0 EN-IEC 60112 /A1 Method for the determination of the proof and the comparative tracking indices of solid insulating materials 2009

EMC 89/336/EEC International Electromagnetic Compatibility 1993

E.43.0 EN-IEC 60533 Electrical and electronic installations in ships - Electromagnetic compatibility, 2015

Page 8 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


E.43.5 IEC 60617-DB Graphical symbols for electrotechnical diagrams (published as database) (- 12-month subscription to online database comprising parts 2

to 13 of IEC 60617)2016

E.44.0 IEC 60747 (All Parts) Semiconductor devices

E.45.0 IEC 60754 (All Parts) Test of gases evolved during combustion of materials 2014

E.46.0 EN 12464-1 Light and lighting - Lighting of work places - Part 1: Indoor work places 2011

E.47.0 EN-IEC 61936-1 Power installations exceeding 1 kV a.c. – Part 1: Common rules 2010

E.48.0 EN 3140+A1 Safety regulations for work at low voltage installations, 2015

E.49.0 EN 3840+A1 Additional Netherlands requirements for high voltage installations, 2015

E.50.0 EN 5152 Electrical symbols, 2016

E.51.0 EN 10034 Rotating Electrical Machines 1993

E.52.0 EN-IEC-61082 Preparation of documents used in electrotechnology - Part 1 2015

E53.0 EN-IEC 60034-1 Rotating electrical machines - Part 1: Rating and performance 2017

E53.0 EN-IEC 60034-1 / C11 Rotating electrical machines - Part 1: Rating and performance 2016

E.54.0 EN 50110 Low Voltage Installations, Provisions for safe works, Inspection & Maintenance 2013

E.54.0 EN 50110-1 Operation of electrical installations - Part 1: General requirements 2013

E.54.0 EN 50110-2 Operation of electrical installations - Part 2: National annexes 2010

E.55.0 IEEE Institute of Electrical & Electronic engineers

E.56.0 ATEX Directive 2014/34/EU Equipment and protective systems intended for use in potentially explosive atmospheres (ATEX) 2014

E.57.0 EN 50014/ 50020/ 50028 Electrical apparatus for potentially explosive atmospheres General 1998

E.58.0 EN-IEC 60079-25:/C11 Explosive atmospheres - Part 25: Intrinsically safe electrical systems 2013

E.59.0 Marine Equipment Directive

2014/90/EU

Marine Equipment Directive 2014

E.60.0 CENELEC European Committee for Electritechnical Standardization

E.61.0 EN-IEC 60228 Conductors of Insulated Cables. 2005

E.62.0 EN-IEC 60331 Tests on Electric Cables Under Fire Conditions. 2009

E.63.0 EN-IEC 60502-2 Power Cables with Extruded Insulation and their Accessories for Rated Voltage. 2014

E.64.0 EN-IEC 60811 A1 Common Test Methods for Insulating and Sheathing Materials of Electric Cables. 2018

E.65.0 EN-IEC 60885 (All Parts) Electrical Test Methods for Electric Cables. 1987-2015

E.66.0 EN-IEC 61508 Functional Safety of Electrical/Electronic/Programmable Electronic Safety Related Systems 2010

E.67.0 EN-IEC 61892 Mobile and Fixed Offshore Units - Electrical Installations. 2015

E.68.0 IEEE 519 Standard Practises and Requirements for Harmonic Control in Electrical Power Systems. 2014

E.69.0 EN-10034 Rotating electrical machines 1994

E.70.0 EN-IEC 60038 IEC standard voltages 2011

E.71.0 EN-IEC 60076-3 Power transformers - Part 3: Insulation levels, dielectric tests and external clearances in air 2013

Page 9 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


E.72.0 EN-IEC 60076-5 Power transformers - Part 5: Ability to withstand short circuit 2006

E.73.0 EN-IEC 60076-11 Power Transformers – Part11: Dry-type Transformers 2004

E.74.0 EN-IEC 62271-103 High-voltage switchgear and controlgear - Part 103: Switches for rated voltages above 1 kV up to and including 52 kV 2011

E.75.0 EN-IEC 60281-1+C1 High voltage fuses – Part 1: Current limiting fuses 2016

E.76.0 EN-IEC 60617-DB Graphical Symbols for Diagrams 2005

E.77.0 EN-IEC 62271-100/A2/C1 High-voltage switchgear and control gear - Part 100: High-voltage alternating-current circuit-breakers 2017

E.78.0 EN-IEC 62271-102:A1/C1 High voltage switchgear and control gear – Part 102: Alternating current disconnectors and earthing switches 2018

E.79.0 ISO 7000 / IEC 60417 Graphical symbols for use on equipment - 12-month subscription to online database comprising all graphical symbols published in IEC

604172014

E.81.0 EN-IEC 61439-6 Low-voltage switchgear and controlgear assemblies - Part 6: Busbar trunking systems (busways) 2012

E.82.0 EN-IEC 60445 Basic and safety principles for man-machine interface, marking and identification - Identification of equipment terminals, conductor

terminations and conductors2017

E.84.0 EN-IEC 62271-106 High-voltage switchgear and controlgear - Part 106: Alternating current contactors, contactor-based controllers and motor-starters 2011

E.85.0 EN-IEC 60688 Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals 2012

E.85.0 EN-IEC 60688/C1 Electrical measuring transducers for converting A.C. and D.C. electrical quantities to analogue or digital signals 2013

E.86.0 EN-IEC 60898 Electrical accessories – Circuit-breakers for overcurrent protection for household and similar installations 1981

E.87.0 EN-IEC 60947-5-1 Low Voltage Switch Gear and Control Gear 2016

E.88.0 EN-IEC 60417 ISO 7000 Electromagnetic Compatibility (EMC) E.79.0)) 1999

E.89.0 EN-IEC 60439-1:/A1 Safety Requirements Electrical Machines Signalling, Indications and Operation Part1: Requirements Visual, Audible and Noticeable

Signals2000

E.90.0 EN-IEC 60439-2:/A1 Mobile and fixed offshore units – Electrical installations - Part 3: Equipment 2000

E.91.0 EN-IEC 60445 High-voltage switchgear and control gear – Part 1: Common specifications 2017

E.92.0 EN-IEC 60446 Convertor Transformers – Part1: Transformers for industrial applications 2007

E.93.0 IEC 60364

NEN-1010:/ EN-5010

Electrical installations for low-voltage - Dutch implementation of the HD-IEC 60364-series 2005-2017

E.94.0 IEC/TR61508: All parts Functional safety of electronic programmable electronic safety related systems 2010

E.95.0 IEC 61511 Fuctional safety (SIL) 2017

E.96.0 ISO 80079-87 Explosive atmospheres 2016

CONTROL SYSTEMS - GENERAL

CG.01.0 ANSI/ISA S84.01 Application of SIS for the Process Industries 2004

CG.02.0 API RP 14 G Fire Prevention and Control, 2007

CG.03.0 IEC 61508 (All Parts) Functional safety of electrical / electronic / programmable electronic safety related systems 2010

CG.04.0 NEN- EN-IEC 61511 (All Parts) Functional safety – Safety instrumented systems for the process industry sector, All Parts 2017

Page 10 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


CONTROL SYSTEMS - FLOW

CF.01.0 AGA report nr. 8 Compressible factors of natural gas and hydrocarbon related gases, 1992

CF.02.0 AGA report nr. 9 Measurement of gas by multipath ultrasonic flowmeters, 2017

CF.03.0 EN 1776 Functional requirements for gas metering systems of natural gas, 2016

CF.04.0 EN-ISO 5167-2 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 2: Orifice

plates2001

CF.05.0 EN-ISO 12213-2 Natural gas – Calculation of compression factor- Part 2: Calculation using molar-composition analysis, 2009

CF.06.0 EN-ISO 5168 Measurement of fluid flow - estimate of uncertainly of flow rate measurements, 2005

CF.07.0 ISO/TR 12765 Measurement of fluid flow in closed conduits- Methods using transit time ultrasonic flowmeters, 1999

CONTROL SYSTEMS - RELIEF VALVES

CR.01.0 API RP 520 - part I Recommended practice for sizing, selection and installation of pressure relieving devices in refineries Part I – Sizing and selection,2000

CR.02.0 API RP 520 - part II Recommended practice for sizing, selection and installation of pressure relieving devices in refineries Part II – Installation, 2003

CR.03.0 API 526 Flanged steel safety valves, 2002

CR.04.0 API 527 Commercial seat tightness of safety relief valves, 2014

CR.05.0 ISO 4126 (All Parts) Safety devices for protection against exessive pressure (safety valves) 2013

CR.06.0 ISO 23251 Safety devices for protection against exessive pressure (pressure relieving and depressuring systems) 2006

CONTROL SYSTEMS - CONTROL VALVES

CV.01.0 ANSI FCI 70-2 Process control valves seat leakage rates, 2013

CV.01.5 EN-IEC 60534-2-4 Industrial control valves – Part 2-4 Flow capacity – inherent flow characteristic and range ability, 2009

CV.02.0 ISA S75 (All Parts) Control valve handbook (Part 1 t/m22)

CV.03.0 EN 12266-1 Industrial valves – Testing of valves Part 1 Pressure tests, test procedures and acceptance criteria – Mandatory requirements 2012

CONTROL SYSTEMS - PRESSURE-MEASUREMENT

CP.01.0 EN 837 (All Parts) Pressure gauges 1996

CONTROL SYSTEMS - TEMPERATURE-MEASUREMENT

CP.01.0 ASME PTC 19.3/2 Temperature Measurement, Instrument and Apparatus 2010/2015

HEATING VENTILATION AND AIR CONDITIONING (HVAC)

Page 11 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


HV.01.0 ASHRAE (All Parts) American Society of Heating, Refrigeration, and Air-conditioning Engineers 2017

HV.02.0 EN 378 (All Parts) Refrigeration systems and heat pumps 2016

HV.03.0 EN ISO 15138 Petroleum and natural gas industries - Offshore production installations - Heating, Ventilation and Air Conditioning, 2007

HV.04.0 ISSO 31 Measure methods for climate installations 2014

HV.05.0 ISSO 32 Principles of temperature simulation calculation 2010

HV.06.0 ISSO 69 Functional diagram for climate installations 2002

HV.07.0 STEK-regeling Stichting Erkenningsregeling voor de uitoefening van het Koeltechnisch installatiebedrijf 2017

HV.08.0 LUKA Principles of ducting 2015

HV.09.0 SMACNA Sheet Metal and air conditioning contractor's national association. (all documents in accordance with equipment or part og HVAC

installation designed2017

HV.10.0 AHRI Air conditioning and refrigeration institute. (all documents in accordance with equipment or part og HVAC installation designed)

FIRE-SAFETY

F.01.0 NEN-EN 2 Classification of fires, 1994

F.02.0 EN 3 (All Parts) Portable fire extinguishers 2010

F.03.0 EN 12259 (All Parts) Fire fighting systems – Components for sprinkler and water spray systems, All Parts 1999-2017

F.04.0 EN 12845 (All Parts) Fixed firefighting systems - Automatic sprinkler systems, Design, installation and maintenance 2004/2015

F.05.0 IMCO Resolution A414 (XI) dated 15 November 1979, including the supplementary joint recommendations ot the countries bordering the North

Sea on the construction and operation of platforms within the framework of the "Conference on Safety and Pollution Safeguards in the

Development of N-W European Offshore Mineral Resources"

1979

F.06.0 LSA - Amendment SOLAS SOLAS-LSA International Life Saving Appliance Code – Amendment of SOLAS, 2010

F.07.0 MODU CODE IMO Publication, IMO-881E, Code for the Construction and Equipment of Mobile Offshore Drilling Units - Annex: Code for the

Construction and Equipment of Mobile Offshore Drilling Units, ISBN 92-801-5109-6, IMO, 2010

F.08.0 NEN 2535 Brandveiligheid Gebouwen Brandmeldinstallaties -systeem-, kwaliteiteisen en projecteringsrichtlijnen, ontwerp 2017

NFPA 10 Standard for Portable Fire Extinguisers 2018

F.09.0 NFPA 11 Standard for low, medium and high explosion foam, 2016

F.10.0 NFPA 13 Standard for the installation of sprinkler systems, 2016

F.11.0 NFPA 15 Standard for water spray fixed systems for fire protection 2017

F.12.0 NFPA 16 Standard for the installation of foam water sprinkler and foam water spray systems, 2015

F.13.0 NFPA 20 Standard for the installation of stationary fire pumps for fire protection, 2016

F.14.0 NFPA 37 Installation and use of Stationary Combustion Engines and Gas Turbines, 2018

F.15.0 NFPA 72 National Fire Alarm Code, 2016

F.16.0 NFPA 750 Standard on Water Mist Fire Protection System, 2015

Page 12 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


F.17.0 NFPA 2001 Standard on clean agent fire extinguishing systems, 2018

F.18.0 PGS 14 Handboek Brandbestrijdingssystemen Publication Series Dangerous Goods, VROM/SZW/V&W, 2016

F.19.0 SOLAS Safety of Live at Sea Protol 1974 incl. amendments until 2017

F.20.0 ISO13702 Control and mitigation of fires and explosions off offshore production installations 2015

F.21.0 EN 1777 Hydraulic platforms (HPs) for fire fighting and rescue services - Safety requirements and testing 2010

F.22.0 EN 14044 High rise aerial appliances for fire and rescue service use 2014

F.23.0 EN 14043 High rise aerial appliances for fire and rescue service use 2014

F.24.0 EN 13731 Lifting bag systems for fire and rescue service use - Safety and performance requirements 2007

F.25.0 EN 14710-1: + A2 Fire-fighting pumps-Fire-fighting centrifugal pumps without primer–Part 1: Classific, general and safety requirements 2005/2008

F.26.0 EN 14710-2: + A1 Fire-fighting pumps - Fire-fighting centrifugal pumps with primer - Part 2: Verification of general and safety requirements 2002/2008

F.27.0 EN-ISO 19353: Safety of machinery - Fire prevention and fire protection 2016

F.28.0 EN 14470-1 Fire safety storage cabinets - Part 1: Safety storage cabinets for flammable liquids 2004

F.29.0 EN 13204 Double acting hydraulic rescue tools for fire and rescue service use - Safety and performance requirements 2016

F.30.0 CEN/TR 14489 Fire-resistant hydraulic fluids - Classification and specification - Guidelines on selection for the protection of safety, health and the

environment2005

F.31.0 ISO/TR 17252 Fire tests — Applicability of reaction to fire tests to fire modelling and fire safety engineering 2008

TRANSPORT PIPELINES

TP.01.0 API 1104 Welding of Pipelines and Related Facilities, 21st Edition, Includes Errata 1), Errata 2 , Errata 3, and Addendum 1 , Addendum 2 2013

TP.02.0 BS 7448 Fracture mechanics toughness tests CTOD, 1997

TP.03.0 EN 288-9 Specification and approval of welding procedures for metallic materials - Part 9 Welding procedure test for pipeline welding on land and

offshore site butt welding of transmission pipelines, 19991999

TP.04.0 NEN-EN-ISO 19232-1 Non-destructive testing - Image quality of radiographs - Part 1 Image quality indicators (wire type) – Determination of image quality

value.2013

TP.05.0 NEN-EN-ISO 2560 Welding consumables - Covered electrodes for manual metal arc welding of non-alloy and fine grain steels - Classification. 2009

TP.06.0 NEN-EN-ISO 3452-1 Non-destructive testing - Penetrant testing - Part 1 General principals. 2013

TP.07.0 NEN-EN-ISO 16810 Non-destructive testing - Ultrasonic examination - Part 1 General principals. 2014

TP.08.0 NEN-EN-ISO 16828 Non-destructive testing -Ultrasonic examination - Part 6: Time-of-flight diffraction technique as a methode for detection and sizing of

discontinuities2014

TP.09.0 NEN-EN-ISO 14171 Welding consumables - Solid wires, solid wire-flux and tubular cored electrode-flux combinations for submerged arc welding of non alloy

and fine grain steels – Classification,.2016

TP.10.0 NEN-EN-ISO 18275 Welding consumables – Covered electrodes for manual metal arc welding of high strength steels – Classification. 2012

TP.11.0 NEN-EN-ISO 14174 Welding consumables – Fluxes for submerged arc welding – Classification. 2012

TP.12.0 NEN-EN-ISO 9016 Destructive tests on welds in metallic materials-Impact tests-Test specimen location, notch orientation and examination. 2011

Page 13 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


TP.13.0 NEN-EN-ISO 4136 Destructive tests on welds in metallic materials – Transverse tensile test. 2011

TP.14.0 NEN-EN-ISO 5173 Destructive tests on welds in metallic materials – Bend tests. 2010

TP.15.0 NEN-EN-ISO 17637 Non destructive testing of welds - Visual testing of fusion-welded joints.Non destructive testing of welds - Visual testing of fusion-welded

joints.Non destructive testing of welds - Visual testing of fusion-welded joints.Non destructive testing of welds - Visual testing of fusion-

welded joints.

2017

TP.16.0 NEN-EN-ISO 9015-1 Destructive test on weld in metallic materials – Hardness testing -Part 1 Hardness test on arc welded joints. 2011

TP.17.0 NEN-EN-ISO 17638 Non destructive examination of welds – Magnetic particle testing. Non destructive examination of welds – Magnetic particle testing. Non

destructive examination of welds – Magnetic particle testing. 2016

TP.18.0 NEN-EN-ISO 23278 Non destructive examination of welds – Magnetic particle testing – Acceptance levels. 2015

TP.19.0 NEN-EN-ISO 17639 Destructive tests on welds in metallic materials – Macroscopic and microscopic examination of welds. 2013

TP.20.0 NEN-EN-ISO 14732 Welding personnel - Qualification testing of welding operators and weld setters weld setters for mechanized and automatic welding of

metallic materials.2013

TP.21.0 NEN-EN-ISO 17636-1-2 Non-destructive examination of welds – Radiographic testing Part 1: X- and gamma-ray techniques with film. Part 2:X- and gamma-ray

techniques with digital recorders.2013

TP.22.0 NEN-EN-ISO 636 Welding consumables – Rods, wires and deposits for tungsten inert gas welding of non-alloy and fine grain steels – Classification. 2017

TP.23.0 NEN-EN-ISO 17640 Non-destructive examination of welds – Ultrasonic examination - Techniques, testing levels and assesment. 2017

TP.24.0 EN 10045-1NEN-EN-ISO 148-1 Metallic materials – Charpy pendulum impact test – Part 1 Test methodMetallic materials – Charpy pendulum impact test – Part 1 Test

methodMetallic materials – Charpy pendulum impact test – Part 1 Test method2017

TP.25.0 NEN-EN-ISO 3183 Petroleum and natural gas industries - Steel pipe for pipeline transortation systems. 2012

TP.26.0 NEN-EN-ISO 10893-8 Non-destructive testing of steel tubes – Part 8: Automated ultrasonic testing of seamless and welded steel tubes for the detection of

laminar imperfections.2011

TP.27.0 NEN-EN-ISO 10893-5 Non-destructive testing of steel tubes – Part 5: Magnetic particle testing of seamless and welded ferromagnetic steel tubes for the

detection of laminar imperfections.2011

TP.28.0 NEN-EN 12668-2+C433 Non-destructive testing - Characterization and verification of ultrasonic examination Equipment - Part 2: Probes. 2010

TP.29.0 NEN-EN 12668-3 Non-destructive testing - Characterization and verification of ultrasonic examination Equipment - Part 3: Combined equipment. 2013

TP.30.0 NEN-EN 12954 Cathodic protection of buried or immersed metallic structures - General principles and application for pipelines. 2017

TP.31.0 NEN-EN-ISO 15609-1 Specification and qualification of welding procedures for metallic materials - Welding prodedure specification - Part 1 Arc welding. 2004

TP.32.0 EN 24063 Welding, brazing, soldering and braze welding of metals – Nomenclature of processes and reference numbers for symbolic representation

on drawings, 19921992

TP.33.0 Bs EN 25580 Specification for minimum requirements for industrial radiographic illuminators for non-destructive testing. 1992

TP.34.0 NEN-EN-ISO 6892-1 Metallic materials - Tensile testing Part 1Method of test at room temperature. 2016

TP.35.0 NEN-EN-ISO 14175 Welding consumables - Gases and gas mixtures for welding and allied processes. 2008

TP.36.0 NEN-EN-ISO 14341 Welding consumables - Wire electrodes and deposits for gas- shielded metal arc welding of non-alloy and fine grain steels –

Classification.2011

Page 14 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


TP.37.0 NEN-EN-ISO 17632 Welding consumables - Tubular cored electrodes for gas shielded and non-gas shielded metal arc welding of non-alloyand fine grain

steels Classification.2015

TP.38.0 NEN-EN-ISO 3834-1 Quality requirements for welding - Fusion welding of metallic Materials - Part 1 Criteria for the selection of the appropriate level of

quality requirements.2006

TP.39.0 NEN-EN-ISO 3834-2 Quality requirements for welding - Fusion welding of metallic materials - Part 2 Comprehensive quality requirements. 2006

TP.40.0 NEN-EN-ISO 3834-4 Quality requirements for welding - Fusion welding of metallic Materials - Part 4 Elementary quality requirements. 2006

TP.41.0 NEN-EN-ISO 3183 Petroleum and Natural Gas Industries - Steel pipe for pipeline transportation systems 2012

TP.42.0 NEN-EN-ISO 3690 Welding and allied processes - Determination of hydrogen content in ferritic steel arc weld metal. 2012

TP.43.0 NEN-ISO 13623 Petroleum and Natural Gas Industries - Pipeline transportation systems. 2017

TP.44.0 NEN-ISO 14313:2007/C1 Petroleum and Natural Gas Industries - Pipeline transportation systems - Pipeline valves. 2009

TP.45.0 NEN-EN-ISO 14723 Petroleum and Natural Gas Industries- Pipeline transportation systems - Subsea pipelie valves. 2009

TP.46.0 NEN-EN-ISO 15589-1-2 Petroleum , petrochemical and Natural Gas Industries - Cathodic Protection of pipeline transportation systems - Part 1: on land pipelines -

Part 2: offshore pipelines2017

TP.47.0 NEN-ISO 15590-1-2-3 Petroleum and Natural Gas Industries - Induction bends, fittings and flanges for pipeline transportation systems -Part 1: induction bends -

Part 2: Fittings - Part 3: Flanges.2009

TP.48.0 NEN-ISO 13623 Petroleum and Natural Gas Industries - Pipeline transportation systems. 2017

TP.49.0 ISO 13628 (All Parts) Subsea production systems (All Parts)

TP.50.0 NEN-EN-ISO 21809-2 Petroleum and Natural Gas Industries - External coatings for buried or submerged pipelines used in pipeline transportation systems –

Part 2 Single layer fusion -bonded epoxy coatings.2014

TP.51.0 NEN-EN-ISO 21809-3 Petroleum and Natural Gas Industries - External coatings for buried or submerged pipelines used in pipeline transportation systems –

Field joint coatings for pipelines2016

TP.52.0 NEN ISO 21809-4 Petroleum and Natural Gas Industries – External coatings for buried or submerged pipelines used in pipeline transportation systems –

Polyethylene coatings (2-layer).2009

TP.53.0 NEN-EN-ISO 21809-5 Petroleum and Natural Gas Industries – Coatings for buried or submerged pipelines used in pipeline transportation systems – External

concrete coatings (2-layer), 2017

TP.54.0 ISO/TR 15464 Petroleum and Natural Gas Industries - Gauging and inspection of casing, tubing and line pipe threads

TP.55.0 NEN 3656 Eisen voor sub-marine transportleidingsystemen, 2015

TP.56.0 NEN 3653 Methods for the determination of NDE acceptance criteria for defects in pipeline girth welds, 2 2009

TP.57.0 NPR-CEN/TS 15173 Gas Supply Systems - Frame of reference regarding Pipeline Integrity Management Systems (PIMS),

TP.58.0 NPR-CEN/TS 15174 Gas Supply Systems - Guideline for safety management systems for natural gas transmission pipelines,

TP.59.0 NTA 8000 Specification of a Risk Management System (RMS) for pipeline systems for the transport of hazardous substances during operations, 2009

STORAGE TANKS

T.01.0 PGS 29 Publicatiereeks Gevaarlijke Stoffen 29, Richtlijn voor bovengrondse opslag van brandbare vloeistoffen in verticale cilindrische tanks,

VROM/SZW/V&W, 2008 Rapportage werkgroep actualisatie met aanbevelingen n.a.v. Buncefield,2016

Page 15 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


T.02.0 PGS 30 Publicatiereeks Gevaarlijke Stoffen 30 Richtlijn buitenopslag in kleine installaties tot 150m3 VROM/SZW/V&W, 2017

WELLHEAD EQUIPMENT

WE.01.0 API 6A (All Parts) Specification for wellhead and Christmas tree equipment 2012

WE.02.0 API 600 (All Parts) Bolted bonnet steel gate valves for petroleum and natural gas industries, 2006 2015

WE.03.0 ISO 4406 Hydraulic fluid power - Fluids - Method for coding the level of contamination by solid particles, 2017

WE.04.0 ISO 15380 Lubricants, industrial oils and related products (class L) family H (Hydraulic Systems), Specification for Categories HETG, HEPG,HEES and

HEPR,2016

WE.05.0 NAS 1638 National Aerospace Standard, Purity requirements for particles in hydraulic systems, 2012

WE.06.0 ISO10423 Specification for wellhead and Christmas tree equipment 2009

WE.07.0 ISO 13533 Drill-through equipment (BOPs)

WE.08.0 ISO 13626 Drilling and production equipment 2003

WE.09.0 ISO13625 Drilling and production equipment 2002

WE.10.0 ISO13624 Drilling and production equipment - Part 1: Design and operation of marine drilling riser equipment 2009

WE.11 ISO14693 Drilling and well-servicing equipment 2003

WE.12 ISO19901(All Parts) Specific requirements for offshore structures - Part 4: Geotechnical and foundation designand and operating considerations 2016

WE.13 ISO19905-3 Site-specific assessment of mobile offshore units 2017

WE.14 ISO17781 Beproevingsmethoden voor kwaliteitscontrole van microstructuur van ferritisch/austenitisch (duplex) roestvast staal 2017

WE.15 ISO17782 Qualification of manufacturers of special materials 2016

WE.16 ISO12439 Mixing water for concrete 2010

WE.17 ISO11960 Steel pipes for use as casing or tubing for wells 2014

WE.18 ISO11961 Steel drill pipe 2008

WE.19 ISO12835 Qualification of casing connections for thermal wells 2013

WE.20 ISO13500 Drilling fluid materials -- Specifications and tests 2008

WE.21 ISO15463 Field inspection of new casing, tubing and plain-end drill pipe 2003

WE.22 ISO15464 Gauging and inspection of threads 2017

WE.23 ISO16070 Downhole equipment -- Lock mandrels and landing nipples 2005

WE.24 ISO16530-1-2 Well integrity - Part 1: Life cycle governance 2017

WE.25 ISO10405 Care and use of casing and tubing 2000

WE.26 ISO10426-1-2-3 Cements and materials for well cementing -- Part 1: Specification 2009

WE.27 ISO13628 Design and operation of subsea production systems -- Part 15: Subsea structures and manifolds 2011

WE.28 ISO10417 Subsurface safety valve systems -- Design, installation, operation and redress 2004

WE.29 ISO10422 Threading, gauging, and thread inspection of casing, tubing and line pipe threads -- Specification 1993

Page 16 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


WE.30 ISO10424-2 Rotary drilling equipment -- Part 2: Threading and gauging of rotary shouldered thread connections 2007

WE.31 ISO10432 Downhole equipment -- Subsurface safety valve equipment 2004

WE.32 ISO10433 Drilling and production equipment -- Wellhead and christmas tree equipment 2001

WE.33 ISO 28781 Drilling and production equipment --Subsurface barrier valves and related equipment 2010

MISCELLANEOUS

X.01.0 ASME Section VIII, Div 1 Guide for ASME Stamp Holders to meet the EC Pressure Equipment Directive (97/23/EC), 2017

X.02.0 NEN 3049 Conversion of Units to S.I. Units, 2017

X.03.0 EN-ISO 9001 Quality management systems – Requirements, 2015

X.04.0 EN 10204 Metallic Products - Types of Inspection documents, 2004

X.05.0 EN-ISO 13702 Petroleum and natural gas industries, Control and mitigation of fires and explosions on offshore production installations – requirements

and guidelines,2015

X.06.0 EN-ISO 14001 Environmental management systems – Requirements with guidance for use for 2015

X.07.0 ISO 3951 (AQL) Sampling Procedures for inspection by variables – Part 1: Specification for Single Sampling Plans Indexed by Acceptance Quality

Limit2013

X.07.5 ISO 11428 Ergonomics visual danger signals, general requirements, design and testing, 1996

X.08.0 ISO 15664 Acoustic noise control design procedures for open plant, 2001

X.08.4 ISO 17020 General criteria for the operation of various types of bodies performing inspections, 2012

X.08.5 ISO 17025 General requirements for the competence of testing and calibration laboraties, 2017

X.09.0 NPR 7910-1 Classification of hazardous areas with respect to explosion hazard-part 1: Gas explosion hazard, based on NEN-EN-IEC 60079-10, 2010

X.09.5 OCMA (No. Mec 1): Recommandation for protection of diesel engines operating in hazard areas, ISBN 10 0471259403 2009

X.10.0 OHSAS 18001: Occupational Health and Safety management Systems (OHSAS) requirements, 2016

X.11.0 ISO 45001 Occupational Health and Safety 2018

X.13.0 PGS 1 (CPR 16) Methoden voor het bepalen van mogelijke schade, Publication Series Dangerous Goods, VROM/SZW/V&W, 2005

X.14.0 PGS 2 (CPR 14E Yellow Book): Methods for the calculation of Physical effects, Publication Series Dangerous Goods, VROM/SZW/V&W, 2005

X.15.0 PGS 3 (CPR 18E Purple Book): Guidelines for Quantitative Risk Assessment, Publication Series Dangerous Goods, VROM/SZW/V&W/RIVM, 2005

X.16.0 PGS 4 (CPR 12 E Red Book) Methods for determining and processing probabilities, Publication Series Dangerous Goods, VROM/SZW/V&W, 2005

X.17.0 Praktijkregels Drukapparatuur

(PRDA)

Requirements for Pressure Equipment, Design, Manufacturing, Maintenance & Inspection (16 katernen), SDU, 2009

X.18.0 EN-ISO 10780 Stationary source emissions - Measurement of velocity and volume flow rate of gas streams in ducts. 1994

X.19.0 KEMA Dutch Rules for Electronic Materials

X.20.0 BS 4832 - ISO 6072: Specification for Compatibility between Elastomeric Materials and Hydraulic Fluids. 2011

X.21.0 EEMUA 140: Noise procedure specification, rev.2. 2014

Page 17 of 18

CODE

NUMBER

TITLE OF CODE /

STANDARD


Ex

pir

y d

ate

REM

AR

KS


X.22.0 ISO IEC 31010: Risc assessment techniques 2009

X.23.0 DNVGL-RP-N101: Risk management in marine and subsee operations 2017

Page 18 of 18