Product DescriptionBuildSecure is a fast setting, structural adhesivedesigned for various “panel on frame” assemblies incommercial and residential construction. BuildSecurehas been certified by Akron Laboratories to pass AFG-01testing and therefore complies with HUD UM-60 and ASTMD-3498 specifications for bonding subfloor construction.BuildSecure can achieve wood tearing bonds in lessthan four hours at 72°F (22°C). The speed of set andultimate shear strength make BuildSecure ideal for shearwall construction and roof assemblies in a productionsetting where timing is of critical importance. The “green strength” and ultimate 500+ PSI shear strength,of this adhesive permits floor decks, shear-walls and roofassemblies to be bonded to each other, forming a rigid“airframe” type construction with strength in all directions.BuildSecure is 100% solids and therefore capable offilling gaps and forming bonds on irregular surfaces withoutshrinking.BuildSecure is a solvent free, non-flammable, moisturecuring adhesive. It complies with all OSHA, State, Localand Federal air quality regulations. This adhesive is non-carcinogenic and complies with California Proposition 65.

Advantages• 100% VOC compliant• Tough elastomeric bonds• Non-flammable• Solvent free• Fast settings• High adhesion• Non-carcinogenic

Technical Data Guide CSI Section No. 07 92 13

Color - Tan

Regulatory Compliance• AFG-01 and HUD use of materials 60• ASTM D 3498• Conforms to OTC Rule for Adhesives • Meets requirements of California regulations: CARB,SCAQMD and BAAQMD

• Conforms to California Proposition 65• Conforms to USDA requirements for non-food contact

Green Standards:• LEED 2.2 for New Construction and Major Renovations:Low Emitting Materials (Section 4.1) eligible for 1 Point

• NAHB Model Green Home Building Guidelines: 5 GlobalImpact Points

• VOC Content: less than 32 grams/liter: ASTM D2369 / EPA Method 24 at 240°F (includes water)

Packaging• 10.1 oz (300 ml)24 cartridges/carton, 45 cartons/pallet

• 20 oz (600 ml) 12 sausages/carton, 45 cartons/pallet

• 5 gallon pails and 50 gallon drums available for special order

Last Revision: 08/30/11CHEM LINK Products LLC

353 East LyonsSchoolcraft, MI 49087www.chemlink.com

Distributed by: BEST MATERIALS LLC Ph: 800-474-7570, 602-272-8128 Fax: 602-272-8014 www.BestMaterials.com Email: Sales@BestMaterials.com

Typical Uncured Properties

Viscosity 800,000 - 1,250,000cps at 72°F (22°C) Industrial Method

Density 11.5 to 12 pounds pergallon ASTM D1475

VOC Content 32 grams/ liter ASTM D2369

Tack Free Time 25 minutes @ 50% RH, 72°F (22°C) ASTM C-679

Skin Time 25 - 30 minutes Industrial Method

Odor Mild Mint Smell Industrial Method

AFG-01 ResultsTest Substrate Required

ShearTestedShear

3.1.1 Test A Wet Lumber 225 lbs 593 lbs

3.1.1 Test B Frozen Lumber 150 lbs 275 lbs

3.1.1 Test C Dry Lumber 225 lbs 838 lbs

3.1.2 Test D Gap Filling 125 lbs 333 lbs

3.2.1.2 Test E MoistureResistance 225 lbs 434 lbs

3.2.1.1 Test E MoistureResistance 90% pass Pass

3.2.2 Test F Oxidation Resistance No fracture Pass

Strength DevelopmentShear (lbs/ square inch)

Time (hours)

Page 2

Basic UsesBonding AFG-01 conforming subfloor structuresBonding roof and wall sheathing to wood and metal studsInstalling EPS foam insulationWood to metal assembliesInstalling cabinetry and sink topsInstalling “tack strip” to secure carpetingStructural insulated panels (SIPs)

Typical Cured PropertiesElongation AtBreak 90 - 110% ASTM D-412

Tensile Strength 550 - 650 psi ASTM D-412

Hardness Shore A 55 - 65 ASTM C-661

Lap ShearStrength 500 - 600 psi ASTM D-1002

Low Temperature Flex

Pass ¼ inch mandrel-20°F (-29°C) ASTM D-816

Shrinkage No measurable shrinkage after 14days

ServiceTemperature -40 to 220°F / -40 to 104°C

Weathering No cracking or chalking, slight mattefinish after 2000 hours QUV “A” bulb

Limitations• In areas where prolonged chemical exposure is anticipated, contact CHEM LINK Technical Services forrecommendations.

• Allow treated wood to “cure” for six months prior to application per APA guidelines.

• Do not use in areas subject to continuous immersion.• Do not store in elevated temperatures. • Remove all coatings and sealers before application.• Do not apply at temperatures below 30°F (-2°C).

MetalPrepare all metal to ensure maximum adhesion. Removeall rust, scale and residue by wire brushing to a brightmetal sheen. Remove films, loose or inappropriatecoatings and oils with an appropriate solvent such asalcohol.* *CHEM LINK recommends that coated substrates be test-ed for adhesion prior to starting a project. Please contactTechnical Services for specific application guidelines andrecommendations.

ConcretePrior to application remove any residual contamination bymechanical abrasion, sand blasting or power washing. Ongreen concrete, remove all release agents, friable andloose concrete. Dry all visible and standing water prior toapplying BuildSecure. Install an appropriate backer rod toavoid three-point bonding.

WoodWood should be clean, sound and dry prior to sealantapplication. Allow treated wood to weather for six monthsprior to application. Remove all coatings and paint (or testfor compatibility) to ensure proper bonding. Do not use onfire retardant lumber.

PrimingIn most instances BuildSecure will not require a primer.However, certain applications or substrates may require aprimer to ensure a long lasting bond and weatherproofseal. It is the applicator’s responsibility to determine theneed for a primer. CHEM LINK recommends a primer beused for any application where prolonged immersion isanticipated.

CautionAvoid prolonged contact with skin. Uncured adhesive irri-tates eyes. In case of contact with eyes, immediately flushwith water. Call a physician. Please refer to the MSDS forFirst Aid information. The most current MSDS can befound at www.chemlink.com.

KEEP OUT OF REACH OF CHILDREN.

Shelf LifeOne year from date of manufacture when stored in normalenvironments. High temperature and high relativehumidity may significantly reduce shelf life. Pails andspecial orders have a shelf life of three months.

StorageStore original, unopened containers in a cool, dry area.Protect unopened containers from water, heat and directsunlight. Elevated temperatures will reduce shelf life.BuildSecure will not freeze.

Clean-UpWet sealant can be removed using a solvent such as alcohol. Cured BuildSecure can be removed by abradingor scraping the substrate.

Page 3

Application InstructionBonding surfaces must be clean, dry and free of dirt,debris, oil, rust and contamination that would interfere withadhesion. Clean metal and painted surfaces with alcoholor ammonia water. Abraded surfaces are acceptable butmust be clean, sound and free of manufacturing defects. Test all substrates for strength and compatibility. Do notuse on olefins such as polyethylene, polypropylene orTPO.BuildSecure is a gun grade mastic that is applied fromcaulking cartridges, or through pumping equipment frompails and drums. Pump ratios of at least 40:1 are requiredfor air driven application equipment. Pumps must have liftsystems and sealed follower plates. All pumpingequipment must be clean and free of water or moisturebefore using. Drum’s and pail’s must be quickly protectedfrom atmospheric moisture when opened. Guns, pumpsand hoses must be sealed when not in use. Butyl, Viton,or Teflon pump seals are required. Polypropylene or Teflonlined hoses are specified for use with polyether basedproducts. Application temperature range is 40°F to 110°F (5°C to44°C) with optimum application from 60°F to 100°F (16°Cto 38°C). Low humidity or low temperature hinder curing.High humidity or high temperature accelerate curing.BuildSecure is a non-slump mastic that can be used onhorizontal, vertical, or overhead applications. Bead sizesfrom 1/16 to 1/4 inch diameter are used for various sizedbonds. Optimum glue line thickness is 15 mils. Do notleave beads unassembled for more than twenty minutes.Bonds can be set and fixtured with nails, screws or staplesuntil adhesive sets. See “green strength” table on pagetwo for rate of strength development. BuildSecure will not shrink. BuildSecure may be used tofill voids around bulkhead penetrations, or for installingwindows and doors. Fill the joint or void and tool to asmooth surface. Do not use on exterior surfaces. Mask offareas as required to protect decorative surface finishes.

Chem Link Inc. P.O. Box 9, Schoolcraft, Michigan, 49087.

Page 4

Patent pending

Notes

Read and ensure that the most up-to-date MSDS and technical guidelines are being followed. Proper use and application arethe responsibility of the applicator. Direct any questions to Technical Services at 800-826-1681 prior to starting the project.

IMPORTANT NOTICEExcept where prohibited by law, CHEM LINK Products makes no warranties, expressed or implied, statutory or otherwise, includingbut not limited to, any implied condition or warranty of merchantability or fitness for a particular purpose. User is responsible fordetermining whether this CHEM LINK Products material is fit for a particular purpose and suitable for user’s method of application.LIMITATIONS OF REMEDIES AND LIABILITYIf this CHEM LINK Products material is proved to be defective, the exclusive remedy at CHEM LINK Products’ option shall be torefund the purchase price or to repair or replace the defective CHEM LINK Products material. CHEM LINK Products shall nototherwise be liable for loss of damages, whether direct, indirect, special, incidental or consequential, regardless of the legaltheory asserted, including negligence, warranty or strict liability.

Distributed by: BEST MATERIALS LLC Ph: 800-474-7570, 602-272-8128 Fax: 602-272-8014 www.BestMaterials.com Email: Sales@BestMaterials.com