Tent Extendable Modular Personnel – Type I 8340-01-185-2616 Type I – 64’ x 20’ Army Surgical Work Area (Green)

The Tent Extendable Modular Personnel (TEMPER) is an aluminum framed supported tent made of vinyl coated polyester duck cloth that is fire, mildew and water resistant. The outer cloth is also visual and electronic suppressive with blackout coated for protection against night optic vision gear. The colors specified have spectral reflectance properties that will camouflage it against the intended terrain. The TEMPER is designed so that it can be extended in 8 ft. increments and set up in multiple configurations. The 8 ft. long extendable middle section comes with either a window or door on each sidewall. The roof panels feature either a stovepipe shield for a standard 4" stovepipe (temperate sections) or two large screened panels for extra ventilation (desert/tropical). Both have weather seal flaps. The liners have a bright white interior and a extra blackout lamination for a tactical environment. The roof fly helps shield the tent from the elements. TYPE I KEY FEATURES: - Made of vinyl coated polyester duck cloth that is fire, mildew and water resistant - Plenums have cloth heating and air conditioning ductwork - Floors consist of single ply cloth and foam insulated cloth both with anti-skid properties - Vestibules have becket and lace connectors that can provide a blackout entrance or connect to other tents as

well as double bump doors

Type I Description: The green Type I TEMPER is an army surgical work area tent that is 20 ft. wide by 64 ft. long. It has 8 vestibules and weighs 4086 pounds. The end walls feature a door that zips closed and has a 54 in. wide and 6 ft. 11 in. height opening. Two polymer windows with screening and weather seal blackout flaps are located on each end section. This tent has a shipping cube of 320 cu. ft.

TEMPER Type I includes the following:

NSN DESCRIPTION QUANTITY 1. 8340-01-186-3014 End Section (Green) 2 2. 8340-01-186-3021 Window Section (Temperate) (Green) 5 3. 8340-01-186-3020 Door Section (Temperate) (Green) 3 4. 8340-01-186-3018 Tent Fly, 16’ (Green) 4 5. 8340-01-392-0921 End Section Liner (Temperate) 2 6. 8340-01-392-0924 Intermediate Liner (Temperate) 6 7. 8340-01-186-3024 Tent Floor, 8’ Single Ply (Green) 8 8. 8340-01-186-3025 Tent Floor, 8’ Insulated 8 9. 8340-01-186-3026 Vestibule w/Door (Green) 8 10. 8340-01-186-3027 Vestibule Floor, Single Ply (Green) 8 11. 8340-01-186-3028 Vestibule Floor, Insulated 8 12. 8340-01-186-3029 Vestibule Container 8 13. 8340-01-186-3032 Partition 3 14. 8340-01-186-3019 Tent Cover (Green) 11 15. 8340-01-186-3030 Tent Pin Container 4 16. 8340-01-186-3035 Plenum, End Wall, 16’ 2 17. 8340-01-186-3036 Plenum, Extendable, 16’ 2 18. 8340-01-823-7451 Tent Pin, Steel 12” 106 19. 8340-01-261-9751 Tent Pin, Wood 24” 54

20. 8340-01-239-7003

Frame, End Section w/Cover Includes: Arch Assembly (2), 8340-01-240-5854 Cable Header (2), 8340-01-477-9657 Purlin Assembly (5), 8340-01-186-3005 Eave Extender Assembly (4), 8340-01-186-3009 Ridge Extender Assembly (2), 8340-01-186-3008 Transport Cover Assembly (1), 8340-01-186-3013

1

21. 8340-01-239-7001

Frame, Window Section w/Cover Includes: Arch Assembly (1), 8340-01-240-5854 Cable Header (1), 8340-01-477-9657 Purlin Assembly (5), 8340-01-186-3005 Eave Extender Assembly (2), 8340-01-186-3009 Ridge Extender Assembly (1), 8340-01-186-3008 Transport Cover Assembly (1), 8340-01-186-3013

4

22. 8340-01-239-7002

Frame, Door Section w/Cover Includes: Arch Assembly (1), 8340-01-240-5854 Cable Header (1), 8340-01-477-9657 Purlin Assembly (5), 8340-01-186-3005 Eave Extender Assembly (2), 8340-01-186-3009 Ridge Extender Assembly (1), 8340-01-186-3008 Door Sil-Purlin Assembly (2), 8340-01-186-3007 Transport Cover Assembly (1), 8340-01-186-3013

3

23. 8340-01-186-3010 Vestibule Frame Assembly (3 per Vestibule) 24 24. 8340-01-263-2546 Door, Double Bump Through (Class A) (Green) 2

PRODUCT SPECIFICATIONS: - Dimensions: 64’Length X 20’Width X 10’ 1/2” Ridge Height and 6’ 9” Eave Height - Floor Area: 1280 square feet - Weight: 4086 pounds - Color: Green - Set-up Time/# of Persons: 50 min. / 9 - Strike Time/# of Persons: 40 min. / 9 - Shipping Cube: 320 cu. Ft. The Technical Manual for this tent is TM 10-8340-224-13.

Test Data

Test Description (Abbreviated) Company

Tested Government

Verified Temperature Range, Operational Minus 25 to plus 120 degrees F. Temperature Range, Storage Minus 60 to plus 180 degrees F. Erect Time / # of Persons Strike Time / # of Persons Durability Withstand 36 erect/strike cycles Field Life Minimum of three (3) years Shelf Life Minimum of ten (10) years Wind Load, Steady Steady wind speed of 55 mph for 30 minutes and resist

rain intrusion Wind Load, Gusts Three occurrences of wind gusts to 65 mph during 30

minute steady wind speed of 55 mph and resist rain intrusion

Rain, Steady Two inches per hour for thirty minutes Rain, Wind Driven Two inches per hour for thirty minutes with wind speeds of

55 MPH and with three occurrences of wind gusts to 65 MPH within the same 30 minute period

Humidity Ambient humidity between zero and 100%, regardless of temperature

Salt Fog Shall withstand exposure to a salt fog atmosphere for 18 months

Snow Load Ten (10) pounds per square foot for 12 hours without damage

Detectability/Blackout Test Five observations with night vision goggles from 300 meters and with the naked eye from 100 meters

Condensation Shall minimize condensation on the inside of the tent that may adversely effect personnel or loss of mission capability

Sunlight Withstand exposure to direct sunlight for 18 months with material temperatures up to 160 degrees F.

Blowing Sand and Dust Not degraded beyond use in a blowing sand and dust environment

Insects Shall resist physical damage from entry of insects from the exterior, including flying insects from penetrating screening mesh diameter of 0.0125 +/- 0.001

Mildew and Fungus Shall not sustain the growth of fungus and bacteria under any conditions, in accordance with ASTM G-21

Petroleum Resistance All components shall resist damage by petroleum products such as, but not limited to, diesel fuel and jet fuel

Mechanical Shock and Vibration In transit bag, shall withstand a simple harmonic motion amplitude of 0.03 inches, frequency from 10 to 55 Hertz for 2 hours in each of three perpendicular directions (total test time of 6 hours)

Rough Handling/Transit Drop In transit bag, shall withstand 6 drops from a minimum of 4 feet at -20 degrees and at 105 degrees F.

Roll In transit bag, shall withstand a circular synchronous mode at 300 RPM for no less than 45 minutes

Breaking Strength Fabric breaking strength shall be a minimum of 250 lbs in the warp and 230 lbs in the fill

Cold Crack Shall be resistant to cold crack at minus 60 degrees F. when tested in accordance with ASTM D2136

Dead Load Seam Strength Fabric seams shall withstand a 50 lb load for 4 hours at 160 degrees F. and a 100 lb load for 4 hours at room temperature

Flame Resistance In accordance with IAW ASTM-D 6413-99 Standard Test Method for Flame Resistance of Textile (Vertical Test)

Lighting Support Shall support two fluorescent field light sets or one incandescent bulb for each nine feet of floor length

Mapboard Support Shall provide connections for the Modular Command Post Map Board and support strap system specified by MIL-B-44381 and 5-4-5531

Ventilation Shall provide non-powered ventilation to maintain a comfortable interior, with an inside temperature no higher than ambient at ambient temperatures up to 90 degrees F.

Electrical Supply Feed Through The electrical supply feed through shall permit the passage of wire bundles up to 5 inch diameter

ECU Feed Through The environmental Control Unit (ECU) feed through shall permit the passage of 18 inch diameter ducts (standardized military specification design)

Stovepipe Shield The stovepipe shield shall permit the passage of a 4-inch diameter stovepipe (standardized military specification design)

Windows Standardized military specification design Wrappers, Transport/Storage Covers Standardized military specification design

Spare Parts & Options for the TEMPER:

NSN DESCRIPTION Photo

1. 8340-01-186-3014 End Section (Green)

2. 8340-01-198-7618 End Section (Tan)

3. 8340-01-186-3020 Door Section (Temperate) (Green)

4. 8340-01-213-6004 Door Section (Temperate) (Tan)

5. 8340-01-186-3015 Door Section (Desert/Tropical) (Green)

6. 8340-01-213-6003 Door Section (Desert/Tropical) (Tan)

7. 8340-01-186-3021 Window Section (Temperate) (Green)

8. 8340-01-198-7619 Window Section (Temperate) (Tan)

9. 8340-01-186-3016 Window Section (Desert/Tropical) (Green)

10. 8340-01-213-6006 Window Section (Desert/Tropical) (Tan)

11. 8340-01-186-3018 Tent Fly, 16’ (Green)

12. 8340-01-198-5358 Tent Fly, 16’ (Tan)

13. 8340-01-186-3017 Tent Fly, 8’ (Green)

14. 8340-01-213-9565 Tent Fly, 8’ (Tan)

15. 8340-01-392-0921 End Section Liner (Temperate)

16. 8340-01-213-9566 End Section Liner (Desert/Tropical)

17. 8340-01-392-0924 Intermediate Liner (Temperate)

18. 8340-01-211-9636 Intermediate Liner (Desert/Tropical)

19. 8340-01-254-5758 Tent Floor, 40’ Single Ply

20. 8340-01-186-3024 Tent Floor, 8’ Single Ply (Green)

21. 8340-01-198-7622 Tent Floor, 8’ Single Ply (Gray)

22. 8340-01-186-3025 Tent Floor, 8’ Insulated

23. 8340-01-186-3026 Vestibule w/Door (Green)

24. 8340-01-198-7621 Vestibule w/Door (Tan)

25. 8340-01-186-3035 Plenum, End Wall, 16’

26. 8340-01-211-6798 Plenum, Side Entrance, 16’

27. 8340-01-186-3036 Plenum, Extendable, 16’

28. 8340-01-186-3032 Partition

29. 8340-01-240-5854 Arch Assembly (Replacement)

30. 8340-01-186-3004 Header Assembly (Replacement)

31. 8340-01-477-9657 Cable Header

32. 8340-01-186-3005 Purlin Assembly (Replacement)

33. 8340-01-186-3009 Eave Extender Assembly (Replacement)

34. 8340-01-186-3008 Ridge Extender Assembly (Replacement)

35. 8340-01-186-3013 Transport Cover Assembly (Green)

36. 8340-01-213-9557 Transport Cover Assembly (Tan)

37. 8340-01-186-3010 Vestibule Frame Assembly

38. 8340-01-186-3027 Vestibule Floor, Single Ply (Green)

39. 8340-01-198-7623 Vestibule Floor, Single Ply (Gray)

40. 8340-01-186-3028 Vestibule Floor, Insulated

41. 8340-01-186-3029 Vestibule Container

42. 8340-01-186-3019 Tent Cover (Green)

43. 8340-01-198-7620 Tent Cover (Tan)

44. 8340-01-186-3030 Tent Pin Container

45. 8340-01-211-4774 Modesty Curtain

46. 8340-00-823-7451 Tent Pin, Steel 12”

47. 8340-00-985-7461 Tent Pin, Steel 18”

48. 8340-00-261-9751 Tent Pin, Wood 24”

49. 8340-01-239-7003

Frame, End Section w/Cover Includes: Arch Assembly (2), 8340-01-240-5854 Cable Header (2), 8340-01-477-9657 Purlin Assembly (5), 8340-01-186-3005 Eave Extender Assembly (4), 8340-01-186-3009 Ridge Extender Assembly (2), 8340-01-186-3008 Transport Cover Assembly (1), 8340-01-186-3013

50. 8340-01-239-7002

Frame, Door Section w/Cover Includes: Arch Assembly (1), 8340-01-240-5854 Cable Header (1), 8340-01-477-9657 Purlin Assembly (5), 8340-01-186-3005 Eave Extender Assembly (2), 8340-01-186-3009 Ridge Extender Assembly (1), 8340-01-186-3008 Door Sil-Purlin Assembly (2), 8340-01-186-3007 Transport Cover Assembly (1), 8340-01-186-3013

51. 8340-01-239-7001

Frame, Window Section w/Cover Includes: Arch Assembly (1), 8340-01-240-5854 Cable Header (1), 8340-01-186-3004 Purlin Assembly (5), 8340-01-186-3005 Eave Extender Assembly (2), 8340-01-186-3009 Ridge Extender Assembly (1), 8340-01-186-3008 Transport Cover Assembly (1), 8340-01-186-3013

52. 8340-01-263-2546 Door, Double Bump Through (Class A) (Green)

53. 8340-01-211-6788 Door, Double Bump Through (Class A) (Tan)

54. 8340-01-186-3001 Foot For Arch (Replacement)

55. 8465-01-220-1419 Strap, Type I Light Support Assembly

56. 8460-00-243-3234 Trunk Locker, Barracks

57. 8340-01-186-3007 Door Sil-Purlin Assembly

58. 6110-01-251-0402 Power Control Box, Type III/120V

59. 3110-01-251-8157 Convenience Outlet, Type III and IV

60. 6150-01-250-6451 Extension Cable, Type III and IV (34”)

61. 6110-01-242-6691 Power Panel Stand Assembly

62. 6230-01-242-2016 Light Set, Type I-Set of Four Lights (TEMPER)