Upload
ngodien
View
234
Download
2
Embed Size (px)
Citation preview
Table Of Contents
01 Test Rig and Course Plan View 02 Test Rig and Course Elevation View 03 Test Rig Cad Details (launching platform)04 Test Rig Cad Details (target landing zones)05 Test Rig Cad Details (mountain range and pylon)06 Test Rig Home Built Sample
Test Rig and CourseSpecifications
Final Design • October 23, 2015
REVISED OCT 23, 2015
The Tech Challenge 2016 Test Rig And Course Plan ViewSCALE: 1/4"=1'-0"
Target Area 1: • Surface area is a 35-3/4” x 1/2” diameter round plywood disc (covered in low pile carpet) supported by 2x4 (1-1/2" x 3-1/2") on edge total height 2" above target area 2. OSH hardware SKU# 253-7264
NOTES:
Target Area 2: • Surface area is a 6'W x 6'W x” x 2”H 1/2" plywood supported by 2x4 (1-1/2" x 3-1/2") on edge (covered in low pile carpet) Target Area 3: • Surface area is a 7'L x 8'W Area defined by banner material Pylon (storm cell): • 10" DIA X 72"H Sakrete™ Model # 65470006 HomeDepot™ Sku # 336963 (requires (2) 48" tubes taped together and trimmed with cardboard base) Mountain range (obstacle): • 6'W x 42"H x 1/2" thick foamcore with gussets for support Challenge course: • 6'W x 22'L banner material Safety zone: • 6'W x 8'L banner material
RENDERING OF 2016EVENT DAY TEST RIG
• Wear safety goggles at all times• Read all warnings on label before use• Critical dimensions are in blue• Tolerance of all parts and dimensions need to be plus or minus 1/4"
Launching platform: • Base: 24"W x 20"H x 48" L fabricated from 1/2" exterior plywood
• Top: 36"W x 60"W x 1/2" Use # 12 wood screws to assemble all parts. (suggested) total height 20-1/2"
1 2 3 4ft0
13'-0"
Ø 10"
6'-0" 5'-0"
2 6'-0
"
8'-0"
22'-0"
37'-0"
35-3/4"
8'-0
"
6'-0
"
7'-0"
6'-0"
26'-0"
23'-0"
3'-0
"
Copyright 2015 The Tech Museum of Innovation®
All of the concepts, designs, and plans represented by this document are the property of TTM and are for use on the project specified in this document. No concepts, designs, or plans shall be used by any person, firm, or corporation for any purpose without the prior written permission of TTM.
Title
Drawing Number
CAD File Name
Drawn By Date
The Tech Museum of Innovation
jvieira 10/23/15
DETAIL CAD PLAN/ELEV VIEW
Target Area 1: • Surface area is a 35-3/4” x 1/2” diameter round plywood disc (covered in low pile carpet) supported by 2x4 (1-1/2" x 3-1/2") on edge total height 2" above target area 2. OSH hardware SKU# 253-7264
NOTES:
Target Aera 2: • Surface area is a 6'W x 6'W x” x 2”H 1/2" plywood supported by 2x4 (1-1/2" x 3-1/2") on edge (covered in low pile carpet) Target Area 3: • Surface area is a 7'L x 8'W Area defined by banner material Pylon (storm cell): • 10" DIA X 72"H Sakrete™ Model # 65470006 HomeDepot™ Sku # 336963 (requires (2) 48" tubes taped together and trimmed with cardboard base) Mountain range (obstacle): • 6'W x 42"H x 1/2" thick foamcore with gussets for support Challenge course: • 6'W x 22'L banner material Safety zone: • 6'W x 8'L banner material
RENDERING OF 2016EVENT DAY TEST RIG
• Wear safety goggles at all times• Read all warnings on label before use• Critical dimensions are in blue• Tolerance of all parts and dimensions need to be plus or minus 1/4"
Launching platform: • Base: 24"W x 20"H x 48" L fabricated from 1/2" exterior plywood
SCALE: 1/4"=1'-0"
The Tech Challenge 2016 Test Rig And Course Elevation View
• Top: 36"W x 60"W x 1/2" Use # 12 wood screws to assemble all parts. (suggested) total height 20-1/2"
1 2 3 4ft0
22'-0"
5'-0"
1'-8
1/2
"3'-6
"4'-0"
35-3/4"
6'-0"
7'-0"
6'-0
"
37'-0"
Copyright 2015 The Tech Museum of Innovation®
All of the concepts, designs, and plans represented by this document are the property of TTM and are for use on the project specified in this document. No concepts, designs, or plans shall be used by any person, firm, or corporation for any purpose without the prior written permission of TTM.
Title
Drawing Number
CAD File Name
Drawn By Date
The Tech Museum of Innovation
jvieira 10/23/15
DETAIL CAD PLAN/ELEV VIEW
Target Area 1: • Surface area is a 35-3/4” x 1/2” diameter round plywood disc (covered in low pile carpet) supported by 2x4 (1-1/2" x 3-1/2") on edge total height 2" above target area 2. OSH hardware SKU# 253-7264
NOTES:
Target area 2: • Surface area is a 6'W x 6'W x” x 2”H 1/2" plywood supported by 2x4 (1-1/2" x 3-1/2") on edge (covered in low pile carpet) Target area 3: • Surface area is a 7'L x 8'W Area defined by banner material Pylon (storm cell): • 10" DIA X 72"H Sakrete™ Model # 65470006 HomeDepot™ Sku # 336963 (requires (2) 48" tubes taped together and trimmed with cardboard base) Mountain range (obstacle): • 6'W x 42"H x 1/2" thick foamcore with gussets for support Challenge course: • 6'W x 22'L banner material Safety zone: • 6'W x 8'L banner material
RENDERING OF 2016EVENT DAY TEST RIG
• Wear safety goggles at all times• Read all warnings on label before use• Critical dimensions are in blue• Tolerance of all parts and dimensions need to be plus or minus 1/4"
Launching platform: • Base: 24"W x 20"H x 48" L fabricated from 1/2" exterior plywood
SCALE: 3/4"=1'-0"
Test Rig Launch Platform Side ViewSCALE: 3/4"=1'-0"
Test Rig Launch Platform Front View
SCALE: 3/4"=1'-0"
Test Rig Launch Platform Plan View
• Top: 36"W x 60"W x 1/2" Use # 12 wood screws to assemble all parts. (suggested) total height 20-1/2"
6'-0
"
5'-0"
1'-8
1/2
"
4'-0"
1/2"
2'-0"
3'-0"
1'-8
"
3'-0
" TO
P
2'-0
" BA
SE
4'-0" BASE
5'-0" TOP
8'-0"
4'-0"
1 2 3 4ft0 Copyright 2015 The Tech Museum of Innovation®
All of the concepts, designs, and plans represented by this document are the property of TTM and are for use on the project specified in this document. No concepts, designs, or plans shall be used by any person, firm, or corporation for any purpose without the prior written permission of TTM.
Title
Drawing Number
CAD File Name
Drawn By Date
The Tech Museum of Innovation
jvieira 10/23/15
DETAIL CAD PLAN/ELEV VIEW
Target Area 1: • Surface area is a 35-3/4” x 1/2” diameter round plywood disc (covered in low pile carpet) supported by 2x4 (1-1/2" x 3-1/2") on edge total height 2" above target area 2. OSH hardware SKU# 253-7264
NOTES:
Target area 2: • Surface area is a 6'W x 6'W x” x 2”H 1/2" plywood supported by 2x4 (1-1/2" x 3-1/2") on edge (covered in low pile carpet) Target area 3: • Surface area is a 7'L x 8'W Area defined by banner material Pylon (storm cell): • 10" DIA X 72"H Sakrete™ Model # 65470006 HomeDepot™ Sku # 336963 (requires (2) 48" tubes taped together and trimmed with cardboard base) Mountain range (obstacle): • 6'W x 42"H x 1/2" thick foamcore with gussets for support Challenge course: • 6'W x 22'L banner material Safety zone: • 6'W x 8'L banner material
RENDERING OF 2016EVENT DAY TEST RIG
• Wear safety goggles at all times• Read all warnings on label before use• Critical dimensions are in blue• Tolerance of all parts and dimensions need to be plus or minus 1/4"
Launching platform: • Base: 24"W x 20"H x 48" L fabricated from 1/2" exterior plywood
SCALE: 1/2"=1'-0"
Test Rig Targets Side ViewSCALE: 1/2"=1'-0"
Test Rig Targets Front View
SCALE: 1/2"=1'-0"
Test Rig Targets Plan View
• Top: 36"W x 60"W x 1/2" Use # 12 wood screws to assemble all parts. (suggested) total height 20-1/2"
35-3/4"
8'-0
"
6'-0
"
7'-0"
6'-0"
35-3/4"
6'-0"
8'-0"
2'-11 3/4"
7'-0"
6'-0"
1 2 3 4ft0Copyright 2015 The Tech Museum of Innovation®
All of the concepts, designs, and plans represented by this document are the property of TTM and are for use on the project specified in this document. No concepts, designs, or plans shall be used by any person, firm, or corporation for any purpose without the prior written permission of TTM.
Title
Drawing Number
CAD File Name
Drawn By Date
The Tech Museum of Innovation
jvieira 10/23/15
DETAIL CAD PLAN/ELEV VIEW
Target Area 1: • Surface area is a 35-3/4” x 1/2” diameter round plywood disc (covered in low pile carpet) supported by 2x4 (1-1/2" x 3-1/2") on edge total height 2" above target area 2. OSH hardware SKU# 253-7264
NOTES:
Target Era 2: • Surface area is a 6'W x 6'W x” x 2”H 1/2" plywood supported by 2x4 (1-1/2" x 3-1/2") on edge (covered in low pile carpet) Target Area 3: • Surface area is a 7'L x 8'W Area defined by banner material Pylon (storm cell): • 10" DIA X 72"H Sakrete™ Model # 65470006 HomeDepot™ Sku # 336963 (requires (2) 48" tubes taped together and trimmed with cardboard base) Mountain range (obstacle): • 6'W x 42"H x 1/2" thick foamcore with gussets for support Challenge course: • 6'W x 22'L banner material Safety zone: • 6'W x 8'L banner material
RENDERING OF 2016EVENT DAY TEST RIG
• Wear safety goggles at all times• Read all warnings on label before use• Critical dimensions are in blue• Tolerance of all parts and dimensions need to be plus or minus 1/4"
Launching platform: • Base: 24"W x 20"H x 48" L fabricated from 1/2" exterior plywood
SCALE: 3/4"=1'-0"
Test Rig Pylon (Storm Cell) Plan/Elevation ViewsSCALE: 3/4"=1'-0"
Test Rig Mountain Range Views
• Top: 36"W x 60"W x 1/2" Use # 12 wood screws to assemble all parts. (suggested) total height 20-1/2"
1 2 3 4ft0
6'-0
"
10"
6'-0"
3'-6
"
3'-6
"
11 1/4"
1/2"
1/2"
6'-0"
Font view
Plan view
Side viewSide view
Plan view
1'-6"
10"
1/2"
Copyright 2015 The Tech Museum of Innovation®
All of the concepts, designs, and plans represented by this document are the property of TTM and are for use on the project specified in this document. No concepts, designs, or plans shall be used by any person, firm, or corporation for any purpose without the prior written permission of TTM.
Title
Drawing Number
CAD File Name
Drawn By Date
The Tech Museum of Innovation
jvieira 10/23/15
DETAIL CAD PLAN/ELEV VIEW
Target Area 1: • Surface area is a 35-3/4” x 1/2” diameter round plywood disc (covered in low pile carpet) supported by 2x4 (1-1/2" x 3-1/2") on edge total height 2" above target area 2. OSH hardware SKU# 253-7264
NOTES:
Target Era 2: • Surface area is a 6'W x 6'W x” x 2”H 1/2" plywood supported by 2x4 (1-1/2" x 3-1/2") on edge (covered in low pile carpet) Target Area 3: • Surface area is a 7'L x 8'W Area defined by banner material Pylon (storm cell): • 10" DIA X 72"H Sakrete™ Model # 65470006 HomeDepot™ Sku # 336963 (requires (2) 48" tubes taped together and trimmed with cardboard base) Mountain range (obstacle): • 6'W x 42"H x 1/2" thick foamcore with gussets for support Challenge course: • 6'W x 22'L banner material Safety zone: • 6'W x 8'L banner material
RENDERING OF 2016EVENT DAY TEST RIG
• Wear safety goggles at all times• Read all warnings on label before use• Critical dimensions are in blue• Tolerance of all parts and dimensions need to be plus or minus 1/4"
Launching platform: • Base: 24"W x 20"H x 48" L fabricated from 1/2" exterior plywood
Test Rig Home Built Sample
• Top: 36"W x 60"W x 1/2" Use # 12 wood screws to assemble all parts. (suggested) total height 20-1/2"
TARGETS(LANDING ZONES)
PYLON(STORM CELL)
MOUNTAINRANGE
LAUNCH PLATFORM
Copyright 2015 The Tech Museum of Innovation®
All of the concepts, designs, and plans represented by this document are the property of TTM and are for use on the project specified in this document. No concepts, designs, or plans shall be used by any person, firm, or corporation for any purpose without the prior written permission of TTM.
Title
Drawing Number
CAD File Name
Drawn By Date
The Tech Museum of Innovation
jvieira 10/23/15
DETAIL CAD PLAN/ELEV VIEW