TO0L - vintagemachinery.org

, -::=:sTHl-2%

9 BURKE MACHINE

TO0L COMPANY

. CONNEAIIT, 01110

C O N N EA UT P R I NT I N G C Or

teizoé

CATALOG OF 7”’ i

Milling Machines

Drill Presses

Tapping Maclhines

Cutting Saws, Etc.

ma BURKE mculma TO0L co.

' CONNEAUT, OHIO

THE BYRKE MACHINE TOOL COMPANY

No. 0 Milling Machine

Longitudinal feed of table . . . . . . . . . . . . . .4 inchesTraverse feed of table . . . . . . . . . . . . . ..1% inchesVertical motion to knee . . . . . . . . . . . . ..31/4, inchesMaximum distance between center of

spindle and table . . . . . . . . . . . . . . . ..4 inchesWorking surface of table . . . . . . . . . . ..3x9 inchesTaper hole in spindle . . . . . . . . . . . . . .No. 7 B. & S.Largest diameter of cone . . . . . . . . . . .414 inchesSmallest diameter of cone . . . . . . . . . . ..21/,, inchesDriving belt . . . . . . . . . . . . . . . . . . . . . ..11;4 inchesHeight over all . . . . . . . . . . . . . . . . . . .151/2 inchesLoose pulley on countershaft . . . . . ..7x21/t inchesSpeed of countershaft . . . . . . . . . ..280 revolutionsWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 lbs.Weight with countershaft boxed . . . . . . . . .160 lbs.

THE BURKE MACHINE TOOL COMPANY


Longitudinal’ feed of table ............................. .. 6 inchesTraverse feed ................ .. .3% inchesVertical motion to knee ............................. .. 5% inchesMaximum distance between center of spindle

and table ................................................... ..7 inchesWorking surface of table ............................... ..3% x 12Greatest distance between centers (6-inch

swing) ................................................... .. 2%; inches

....6 inchesLargest diameter of cone... .. .

....3V2 inchesSmallest diameter of cone...Driving Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..2 inchesTaper hole in spindle .. ...B. and S. No. 9Hole in spindle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..% inchHeight over all ................... .. ...21 inchesLoose pulley on countershaft... . . . . . . . . . . ..7 x 2%Speed of countershait ............ .. ...28o revolutionsWeight complete ...... .190 poundsWeight packed...... .................................... ..260 pounds



Longitudinal feed of table . . . . . . . . . . . ..8% inchesTraverse feed . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 inchesVertical motion to knee . . . . . . . . . . . . . . . . . ..6 inchesMaximum distance between center of spindle

and table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..8 inchesVVorking surface of table . . . . . . . . . . . . . . . ..3% x 16

Greatest distance between centers (6—inchswing) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..6:/3 inches

Largest diameter of cone . . . . . . . . . . . . . . . ..6 inchesSmallest diameter of cone . . . . . . . . . . . . . ..3% inchesDriving Belt . . . . . . . . . . . . . . . . . . . l . . . . . . . . ..2 inchesTaper hole in spindle . . . . . . . . . . . ‘.B. and S. No. 9

Hole in spindle . . . . . . . . . . . . . . . . . . . . . . . . . . ..% inchHeight over all . . . . . . . . . . . . . . . . . . . . . . . .. 22 inchesLoose pulley on countershaft . . . . . . . . . . . . . ..7 x 2%Speed of countershaft . . . . . . . . . i . . ..280 revolutionsWeight complete . . . . . . . . . . . . . . . l . . . . ..210 poundsVVeight boxed . . . . . . . . . . . . . . . . . . . . . . . ..29O pounds



Longitudinal feed of table . . . . . . . . . . . . ..6 inchesTraverse feed . . . . . . . . . . . . . . . . . . . . . .314 inchesVertical motion to knee . . . . . . . . . . . . . .8-‘$4, inchesMaximum distance between center of

spindle and table . . . . . . . . . . . . . . . ..7 inchesWorking surface of table . . . . . . . ..317§x12 inchesGreatest distance between centers

(6 inch swing) . . . . . . . . . . . . . . . ..2% inchesLargest diameter of cone . . . . . . . . . . . . . . .6 inchesSmallest diameter of cone . . . . . . . . . . ..3% inchesDriving belt . . . . . . . . . . . . . . . . . . . . . . . . ..2 inchesTaper hole in spindle . . . . . . . . . . . .B. and S. No. 9Hole in spindle . . . . . . . . . . . . . . . . . . . . . ..% inch

\Height over all . . . . . . . . . . . . . . . . . . ..2517é inchesLoose pulley on countershaft . . . . . . . .7x21/4 inchesSpeed of countershaft . . . . . . . . . ..280 revolutionsWeight complete . . . . . . . . . . . . . . . . ..235 poundsWeight boxed . . . . . . . . . . . . . . . . . . . . . .300 pounds

THE BURKE MACHINE TOOL COMPANYTHE BURKE MACHINE TOOL COMPANY

_ No. 5 Milling MachineN0. 4 Milling Machine V 12 in. by 5% in. by 9 in.

The front bronze bearing, 3% in. long, is tapered.Longitudinal feed of table...Traverse feed Large end 1 15-16 in. inside diameter.Vertical motion to knee..Maximum distance between center of spindle and table inches The rear bearing is straight’ 2 3/8 in‘ long’ taperedWorking surface of table........................ ........3%xi6 inches outside with nut to take 1 we-ar_Greatest distance between centers (6 inc ...6% inches ‘ ID

'i}"sI'u}'i'£(;;'3' Lariaestdiamieterof Cone--~ (“Inches ' The knee has solid top and is counterbalanced.

Snigllestbdilameter of cone 3,4 inchesDriving e .... ..2 inc es Sh ft f ' ' 'Tape? hokfin Spindle B and S_N0_9 a or table gear runs in eccentric bushings toHole in spindle..... ..1/2 inch take up wear.Height overall..... "2554 inches _ _ _

Loose pulley on countershaft 7x2% inches The spindle 1S crucible steel drop forged and hasSpeed of countershnft 8o revolutions 1 th b . k . .wag“ compmm ‘.250 pounds arge rust earing to ta e Jars off bearing.Weight boxed . . . . . . . . . . . .. 350 pounds



SPECIFICATIONS

Longitudinal feed . . . . . . . . . . . . . . . . . . . . .12 in.Longitudinal feed with one setting of lever. . .5 in.Traverse feed . . . . . . . . . . . . . . . . . . . . . . ..534 in.Vertical feed . . . . . . . . . . . . . . . . . . . . . . . . ..9 in.Working surface of table . . . . . . . . . . .5 in. x 16 in.Table over all . . . . . . . . . . . . . . . . . . ..7 in. x 20 in.Width of T slot . . . . . . . . . . . . . . . . . . . . . . ..5/g in.Maximum distance center of spindle to table. .10 in.Distance center of spindle to arm . . . . . . . . .51/4, in.Taper hole in spindle . . . . . . . . . . . . . .B. & S. No. 9

Hole through spindle . . . . . . . . . . . . . . . ..17-32 in.Diameter of cone . . . . . . . ..5%, 6%, 81/3, 9% in.Width of belt . . . . . . . . . . . . . . . . . . . . . . . ..2% in.Countershaft pulleys . . . . . . . . . . . ..10 in. X 3 in.Speed of countershaft . . . . . . . . . . . . ..200 R. P. M.Height of machine . . . . . . . . . . . . . . . . . . . . ..54 in.Weight of machine (net) . . . . . . . . . . . ..1000 lbs.Weight of machine (crated) . . . . . . . . . . . .1150 lbs.Floor space . . . . . . . . . . . . . . . . . . . . M20175 x 27%


Two Spindle Milling Machine

Longitudinal feed of table . . . . . . . . . . . . . . ..6 inchesTraverse feed of table . . . . . . . . . . . . . . . . ..2% inchesVertical motion of knee . . . . . . . . . . . . . . . ..5% inchesWorking surface of table . . . . . . . . . . ..l2 x 4 inchesMaximum distance between center of spindles,

_ 6% inchesMinimum distance between center of spindles,

4 inchesLargest diameter of cone . . . . . . . . . . . . . . . ..6 inchesSmallest diameter of cone . . . . . . . . . . . . ..3% inchesDriving belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..2 inchesTaper hole in spindles . . . . . . . . . . . . ..No. 9 B. and S.

Height over all . . . . . . . . . . . . . . . . . . . . . ..25 inchesPulleys on counter shaft . . . . . . . . . . . .7 x 2% inchesSpeed of counter shaft . . . . . . . . . . ..280 revolutionsWeight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..40O pounds


Vertical Milling Attachment for‘

Nos. 3 and 4

. ¢7VIilling ;7VIachines

This Vertical Milling Attachment is especially adapted

for use on our No. 3 and 4 Milling Machines and the

spindle is constructed to use draw in collets. One collet,either )4, ya or 72 inch is furnished with the attachment,X», inch collet being the largest which can be used. Thegearing in this attachment is two to one, so that the

spindle runs at twice the speed of the Milling Machinespindle, giving a speed of from 200 to ‘.500 revolutionsper minute.

Weight 19 pounds.


Index Centers

TILTING HEAD

STATIONARY HEAD

These Index Centers are especially designed for therapid production and indexing of light work of any kind.

The spindle is reamed for B. and S. Taper No. 7 andis also threaded so that a face plate can be used.

One Dial Plate of 48 divisions furnished unless other-wise ordered.

VVeight of Tilting Head, 20 pounds. Six inch swing.V’Veight of Stationary Head, 15 pounds.


Slotting Attachment

WITH GEAR COVER REMOVED

This attachment is baekgeared so that a heavy cut can

be taken and is for use on our Nos. 3 and 4 MillingMachines. The slide can be set at any angle not ex-

ceeding I0 degrees either side of the center.

Stroke, I inch.

Weight, 23 pounds.


Draw-in Attachments

No. 0 MILLING MACHINE

For this purpose the spindle is made of toolsteel and hardened. The nose is ground to receiveNo. 3 Cataract Chuck equipped with draw-in rodto hand wheel on the rear of machine. one colletfurnished—1/2 in. maximum capacity.

Nos. 1 to 5 MILLING MACHINES

A removable, hardened and ground bushing isfitted to the No. 9, B. & S. taper of the spindle.

From the chuck a solid rod extends throughthe bushing and spindle to the hand-Wheel on theback of the machine.

No. 3 Cataract Chucks with a maximum sizeof 15 inch are used exclusively.

INDEX CENTERS

The quill of the center is built to order to takea No. 3 Cataract Chuck (maximum size 1/2 inch)with draw-in attachment and can be used for chuckonly.


Arbors

Standard Arbors for all our Milling Machines

‘regularly furnished in 1;é in., % in., % in., 7/gin.and 1 in. diameter.

Quick Milling Attachment

For use in large screw feed Milling Machines.

Furnished for % -in. '1‘ slot unless otherwise ordered.

Working surface of table . . . . . . . . .3 1/2 in. x 12 in.Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..7 in.Length of Rack . . . . . . . . . . . . . . . . . . . . . . . . . .8 in.Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..36 lbs.\Veigl1t Boxed . . . . . . . . . . . . . . . . . . . . . . . . .42 lbs.


ColumnsCabinet Column for No. 0 Miller.

Size of top . . . . . . . . . . . . . . . . . . . . . . . . ..9x6% in.Size of base . . . . . . . . . . . . . . . . . . . . . . ..101/2x8 in.Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 in.Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..50 lbs.

Column for Nos. 1, 2. 3, and 4 Millers,' C & D Tappers.

Size of top . . . . . . . . . . . . . . . . . . . . . . .10x13 1/; in.Size of base . . . . . . . . . . . . . . . . . . . . . . .121/2x16 in.Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..23 in.Vveight . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..90 lbs.

The above regularly furnished but We can furnishthe following if especially ordered:

Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..28 in.Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..115 lbs.

Column for A and B Tappers. «

Size of top . . . . . . . . . . . . . . . . . . . . . ..6%x91/_» in.Size of base . . . . . . . . . . . . . . . . . . . . . . . .14x14 in.Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..34 in.Vveight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 lbs.

Column for Drill Press.

Diameter of top . . . . . . . . . . . . . . . . . . . . . . . .914 in.Diameter of base . . . . . . . . . . . . . . . . . . . . . . .16 in.Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 in.Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..5O lbs.


No. 0 - 10 in. Sensitive Drill Press

SPECIAL FEATURES

‘*7

Double Flange Top Cone.Ball Bearing Thrust.Spindle and Quill both ground to size and all

parts interchangeable.Attached countershaft.

Taper to fit 5-16 Almond Chuck.

Specifications on next page.

Extra charge for column, weight 50 pounds.Height 35 inches.


No..1 - 10 inch Sensitive Drill Press.

Specifications of Nos. 0 and 1 Drill Press

Greatest distance from spindle to table..7% inchesVertical movement of spindle . . . . . . . . . . ..2% inchesVertical movement of table . . . . . . . . . . . . . ..7 inchesDiameter of table . . . . . . . . . . . . . . . . . . . . . . ..8 inchesDistance from center of spindle to frame.5%; inchesDrilling capacity . . . . . . . . . . . . . . . . . . . . ..0 toT5B. inchSize of tight and loose pullev .. .. ....l1/2 x 4 inchesSpeed of driving pulley . . . . . . . . . . ..550 revolutionsWeight of No. 0 Drill Press . . . . . . . . . . ..45 poundsWeight of No. 0 Drill Press crated.. . . . .60 poundsWeight of No. 1 Drill Press . . . . . . . . . . ..50 poundsWeight of No. 1 Drill Press crated...._.65 pounds


No. A Tapping Machine

POSITIVE DRIVE

This Tapping Machine is operated by a steel pin

clutch working between the two pulleys which are

driven by open and cross belts.

Furnished regularly with tapered spindle tofit No. 2 Almond or Jacobs Chuck.

When especially ordered we will furnish drawin collet chuck 14 in. capacity without extra charge.All taps with smaller shank will have to be bushed.

SpecificationsFoot-stock spindle has a movement of ..2;./5, inchesSize of pulleys . . . . . . . . . . . . . . . . . . . . ..4 x 1%; inchesCapacity . . . . . . . . . . . . . ..%; inch to the smallest holeSpeed of spindle . . . . . . . . . . . . . . . . . ..200 revolutionsWeight of machine . . . . . . . . . . . . . . . . . . . ..l8 poundsWeight of machine ready for shipment...25 pounds

Extra charge for column, weight, 70 pounds.Countershaft, weight, 40 pounds.

Speed. 120 revolutions.

4


No. B Tapping Machine

FRICTION DRIVE

This Tapping Machine is operated by a disc

operating between the inner faces of the piilleyswhich are lined with leather.

These pulleys run on bronze bearings and IIFP

driven by open and cross belts.Furnished regularly with tapered spindle to fit

No. 2 Almond or Jacobs Chuck.When especially ordered we will furnish draw

in collet chuck 14 in. capacity without extra charge.All taps with smaller shank will have to be bushed.

SpecificationsFootstock spindle has a movement of....2% inchesSize of pulleys . . . . . . . . . . . . . . . . . . . . . . . .5 x 1 inchCapacity . . . . . . . . . . . . . . . . . . . ..smallest to T3Tfll'lCl'l€S

Size of belt used . . . . . . . . . . . . . . . . . . . . . . . . . ..1 inchSpeed of spindle . . . . . . . . . . . . . . . .. 200 revolutionsWeight of machine . . . . . . . . . . . . . . . . . . . ..l8 poundsVVeight of machine ready for shipment...25 pounds

Extra charge for column weight 70 pounds.Countershaft, weight, 40 pounds.

Speed 120 revolutions.

,

._

...T

~...

...._

._,.—

-..


No. C Tapping‘MachincCLUTCH DRIVE

This Tapping Machine is operated by two ex-

panding ring clutches, one in each pulley, thesepulleys being driven by straight and cross belts.

Furnished regularly with tapered spindle tofit No. 2 Almond or Jacobs Chuck.

When especially ordered we will furnish drawin collet chuck 14 inch capacity without extracharge. All taps with smaller shank will have tohe hushed.

SpecificationsFootstock spindle has movement of . . . . ..3f/2 inchesSize of pulleys . . . . . . . . . . . . . . . . . . . ..61/2 x 2 inchesCapacity . . . . . . . . . . . . . . . . . . . . . . . . . . ..up to 3,5 inchSize of belt . i . . . . . . . . . . . . . . . . . . . . . . . . ..l3/l inchesSpeed of spindle . . . . . . . . . . . . . . . . . ..l00 revolutionsWeight of machine . . . . . . . . . . . . . . . . . . . ..40 poundsVi/eight of machine boxed . . . . . . . . . . . . ..50 poundsExtra charge for countershaft, weight, 49 pounds.

Speed, 90 revolutions.


No. D Tapping Machine

CLUTCH DRIVE

This Tapping Machine is operated by two ex-

panding ring clutches, one in each pulley, thesepulleys being driven by straight and cross belts.

\’Ve furnish this spindle tapered to fit a No. It

Little Giant double grip chuck.

Specifications

Foot stock spindle has a movement of. . . .5 inchesDiameter of pulleys . . . . . . . . . . . . . . . . . ..9 inchesSize of belt used . . . . . . . . . . . . . . . . . . . .214 inchesCapacity . . . . . . . . . . . . . . . . .Taps to 5/8 inch holesSpeed of spindle . . . . . . . . . . ..50 to T5 revolutions\Veight of machine . . . . . . . . . . . . . . . . ..85 poundsWeight of machine ready for shipment.l00 pounds

Extra charge for column, weight, 85 pounds.

Countershaft, weight, 90 pounds.

Speed, 45 to 60 revolutions.


Twelve Inch and ‘Twenty lnch

Cutting Off Saws

TWELVE INCH SAW

Special Features

Fric-tion Power Screw Feed.

Automatic Knockout which can he set at any point.

Large (‘.lam1Jing Table.

The Steady drive we get from our Compact SawCarriage (patent allowed) eliminates back lashand reduces breakage of blades to a minimum.


Saw Grinder

For grinding or regumming any Saw Blades from

10 inches to 20 inches in diameter.

Description of _Saw

Saw Carriage

As shown, the saw blade rests on and is bolteddirect to the bronze worm wheel and in additionto the three half-inch cap screws it is driven bythree half-inch hardened drill rod pins.

These six driving holes are far away from thecenter of the blade and give unusual leverage.

__

,_

.-r

.._

.0.7-.

4..1

-..-..‘

,...e

.v...g

,.,_........‘.r.._n......_v.—

.;...-r_..,,...x.a

.u

._

._

g—

_:._


This worm wheel with attached saw is mountedin a carriage sliding in suitable ways in the frame

of the machine and is held in place by the loose

shaft B. Mounted on the front of the saw car-

riage is the steel casting A which acts as a guidefor the blade and as a stripper plate for the chips.

Feed

The carriage is driven forward against the work

by the square thread screw C which revolves in a

solid nut mounted under the carriage. This feed

screw is driven by gearing from the main drive.In this chain of gears is a loose gear confined be-

tween two flanges lined with leather. A springand adjusting collar tightens these flanges to thegear and completes ‘the friction feed.

Knockout

After the work has been clamped on the table

and the saw brought to the work by the hand wheel,the feed is thrown in by the feed lever which actu-ates a square jaw clutch in the gearing. This clutchis disengaged and the feed stopped by a trip whichis adjustable.

Suitable guards cover all gears.

Variable Speed

We also build the 12 inch size with a three

step cone in place of the tight and loose pulleys, fur-

nishing With this a suitable countershaft.


Specifications of Saws

Diameter Saw Blades . . . . . . .12 in. . . . . . . .20 in.Thickness of Saw Blades. . . . $5; in. . . . . .3-16 in.Capacity Rounds . . . . . . . . . . ..3 in . . . . . ..5% in.Extreme Capacity . . . . . . . . . .3x5 in. . . .5%x12 in.Capacity 1/; inch flat . . . . . . ..9 in . . . . . . ..20 in.Capacity “I” Beams flat . . . . ..5 in . . . . . . ..12 in.Clamping Surface . . . . . . . .‘10x16 in. . . . .14x34 in.Cutting Speed per min . . . . . . .23 ft . . . . . . . .23 ft.Feed per min . . . . . . . . . . ..6-10 in. .4-10 & 1 in.Speed of Pulleys. .600 Rev. per mi. 450 Rev. per mi.T. & L. Pulleys . . . . . . . . . ..8x2 in . . . . ..10x3 in.Floor Space . . . . . . . . . . ..26x35 in. . . . .30x76 in.Height of Table . . . . . . . . . . ..23 in . . . . . . ..26 in.Net Weight . . . . . . . . . . . . .550 lbs. . . . .1100 lbs.Gross Weight . . . . . . . . . . . . .600 lbs. .. . .1200 lbs.

TWENTY INCH SAW


Coal Oil Forge(Patent applied for)

This forge is designed to meet all _the require-

ments of all round machine shop practice.It is economical, clean and easily operated. Be-

ing self-contained, it can be moved from one part ofthe shop to another, wherever needed. ‘Furnishingthe amount of heat necessary for ordinary work,each burner consumes 1 gallon of coal Oll per dayof 10 hours.

The melting pot, which sets in the top of the forge,will hold sufficient babbit or lead for ordinary use,and is easily heated to the necessary degree of heat.

Fire brick pieces are furnished to close the rearand front openings.

The interior is 5% inches wide, 4% inches highand 9 inches deep.

Weight, 160 pounds. '\’\/eight, crated, 210 pounds.


Coal Oil Forge Directions

The Forges are thoroughly tested before cratingand as shipped contain one-half gallon of water and

in case same is ever emptied, be sure and replace

this amount of water.

Mount the burners and take out filling plug in

back and open pet cock. Fill tank with oil and re-

place plug. Close pet cock. Be sure burner valve

is closed. Pump up pressure to at least 40 poundsPour gasoline in bottom of burner and light. \Vhenabout consumed, open valve and very gradually letoil into coil. A sudden rush of cold oil will chill the

coil and necessitate heating over again. \Vatcl1

the burner very closely until the steel tubing be-

comes red hot at the end. Then open the valve

M; open. The higher the pressure the more intense

the heat.

The burner should be blown out once for every

10 hours’ use, as follows: \Vhen through using forge,close valve quickly, remove nipple and open valve,

allowing a very little oil into coil. This will blow itout. Clean nipple and replace. For every week's

steady use, the steel plug in top of burner should be

removed and any carbon which has collected re-

moved withia No. 30 drill. Then start forge and

blow out as above. Once a year take out the % inchnipple which supports the burner. wash the carbor-undum packing which it contains and replace.

Use ordinary coal, carbon or kerosene oil.

Shelby tubing 1% x 16 gauge, 6% inches long.By mail . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . .. 20c

Gas nipples . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 10c

..-4

...s.;£......._,..-....-

.......

......‘.=

-_

....4

».

-\1

£-::-

.-~

w»

‘WC

«W

.-.

..—

r..

—.—

_u

Z-vvnw

-s<

:*w

=r

n.~

..—

e.r

~,-

...-

..t

».m

..x

..v.......,..-


Hydraulic Pressure Pump

Designed especially to pump water for testing valves.

Will pump up to 250 lbs. pressure.

Fittings for V2 Inch Pipe

Diameter Cylinder.......................................... ..1 inchStroke ........................................................ .. 3 inches

Size Pulley ...................................................... ..12 x 3

Size Belt ............ .. 3inches

Speed .............................................. ..5o Rev. per min.‘Floor Space ........................................... ..8 x 18 inches

Height ....................................................... ..27 inches

Weight .................................................... ..13o pounds


Code

Cable Address, "BURKMACO,” Conneaut. Ohio

Lieber’s, A. B. C. Fifth Edition andWestern Union odes Used.

No. 0 Bench Milling Machine . . . . . . . . . . . . ..TrialNo. 1 Bench Milling Machine . . . . . . . . . . . . . ..TabNo. 2 Bench Milling Machine . . . . . . . . . . . . ..Tacl;N0 3 Bench Milling Machine . . . . . . . . . . . . . . .TailNo. 4 Bench Milling Machine . . . . . . . . . . . . ..Tall;No. 5 Milling Machine . . . . . . . . . . . . . . . . . . ..Tucl<Two Spindle Milling Machine.- . . . . . . . . . . . . .TallyCabinet Column for No. 0 Milling Machine. .TrunkColumn for Nos. 1 to 4 Milling Machines. . . .TameIndex Centers (Tilting Head) . . . . . . . . . . . ..Tanl{Index Centers (St'ationary Head) . . . . . . . . ..TaperExtra Index Plates . . . . . . . . . . . . . . . . . . . . . . ..TarDraw-in Collet for Milling Machine . . . . . . . ..Tasl;Draw-in Collet for Index Centers . . . . . . . . . ..TaxVertical Milling Attachment . . . . . . . . . . . . . . ..TeaSlotting Attachment . . . . . . . . . . . . . . . . . . . . ..TernMiller and Drill Press Vise, Plain . . . . . . . . . . . .TextMiller Vise (Swivel) . . . . . . . . . . . . . . . . . . ..Then1eQuick Opening Vise . . . . . . . . . . . . . . . . . . . . . . .'l‘rotNo. 5 Vise . . . . . . . . . . . . . . . . . . . . . . . . . . ..TurbanArbors 1/2 in. % in. 34 in. 7/8 in. 1 in.lVIi1lers-No.’ 0 Rethill, Rething, Rethong, Rethrone, Rethumb1 to 4 Thill, Thing, Thong, Throne, ThumbNo. 5 Thilled, Thinged, Thonged, Throned, Tliumbed -

Quick Milling Attachment . . . . . . . . . . . . . . . ..TreeNo. A Tapper . . . . . . . . . . . . . . . . . . . . . . . . . . ..TideNo. B Tapper . . . . . . . . . . . . . . . . . . . . . . . . . . ..TierCountershaft for A and B Tapper . . . . . . . . . . .TigerColumn for A and B Tapper . . . . . . . . . . . . . . ..TileNo. C Tapper . . . . . . . . . . . . . . . . . . . . . . . . . . . .Tin1e

' Countershaft for No. C Tapper . . . . . . . . . . . . ..TinColumn for C Tapper . . . . . . . . . . . . . . . . . . . . ..Tip

_._

Y....,.....—

..-

......—

,._

»......w

.~=

..w

........,..._

..,.._—

-.—

-.v.a.-........-Q

.......u-an

-m

mIr

.-sh

y-a

x1

—

-..;

.».n

.u~

Countershaft for No. D Tapper . . . . . . . . . . . ..Tit1eColumn for D Tapper . . . . . . . . . . . . . . . . . . . . .ToadNo. 1 Coal Oil Forge, 1 Burner. .( . . . . . . . . . .TokenNo. 2 Coal Oil Forge, 2 Burners . . . . . . . . . . . . .TonBurners for Forge . . . . . . . . . . . . . . . . . . . . . .Tonic

‘Steel Tube for Burners . . . . . . . . . . . . . . . . ..ToolBrass Gas Nipple for Burners . . . . . . . . . . . . . .TopTwelve-inch Rotary Cutting Off Saw . . . . . . . .TopazTwelve-inch Rotary Cuttng Off Saw, with

variable speed. . .’. . . . . . . . . . . . . . . . . . .TorchExtra Twelve-inch Blades . . . . . . . . . . . . . . ..TotemTwenty-inch Rotary Cutting Off Saw . . . . . . . . .TourTire Mold Cutting Saw . . . . . . . . . . . . . . . . . ..TulipExtra Twenty-inch Blades . . . . . . . . . . . . . . . ..TowSaw Grinder, 10 in. to 20 in . . . . . . . . . .. .Towe1Pressure Pump . . . . . . . . . . . . . . . . . . . . . . . . .ToWnNo. 0 Drill Press . . . . . . . . . . . . . . . . . . . . . . ..TrainNo. 1 Drill Press . . . . . . . . . . . . . . . . . . . . . ..TrampDrill Press Column . . . . . . . . . . . . . . . . . . . . ..TrashMillers Falls Chuck . . . . . . . . . . . . . . . . . . . . ..Turf

Millers Falls Chucks

Millers Falls Chucks of 3/3 in. maximum capac-ity furnished with our 'Drill Presses and TappingMachines for 75 cents ext/ta. The Spindle, how-ever, must be especially threaded to receive thisChuck and it will not fit our standard spindle.

Documents

TO0L - vintagemachinery.org