Upload
papematarsarr
View
18
Download
1
Embed Size (px)
Citation preview
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 1
ATM gère deux types de liaisons :
- Les liaisons points à point
- Les liaisons point à multipoint
De manière générale, les liaisons points à point relient de façon fixe deux machines. Dans le
réseau ATM, les liaisons point à point permettent d’envoyer systématique les paquets à
l’autre extrémité du lien. Dans ce paragraphe, nous allons mettre en œuvre la liaison de type
point à point dans un réseau ATM.
1- Architecture
Paramétrage du commutateur
Pour bien paramétrer les ports d’un commutateur, il est important de maîtriser les notions de circuit
virtuel(VC), de chemin virtuel (VP) et de VPI (Virtual Path Identifier).
J’ai paramétré les ports du commutateur en associant sur le port 1 un VPI 1 et le VCI 100 (1/100), et
le port 2 est associé au VPI2 et le VCI 200 (2/200).
LAB 1 : INTERCONNEXION POINT A POINT VIA UN COMMUTATEUR ATM
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 2
Configuration de routeur R5
R5(config)#interface a1/0
R5(config-if)#no ip address
R5(config-if)#no shutdown
R5(config-if)#exit
R5(config)#interface a1/0.1 point-to-point
R5(config-subif)#ip address 172.16.0.1 255.255.255.0
R5(config-subif)#pvc 1/100
R5(config-if-atm-vc)#protocol ip 172.16.0.2 broadcast
R5(config-if-atm-vc)#encapsulation aal5snap
Diagnostique
R5#show ip interface
FastEthernet0/0 is administratively down, line protocol is
down
Internet protocol processing disabled
ATM1/0 is up, line protocol is up
Internet protocol processing disabled
ATM1/0.1 is up, line protocol is up
Internet address is 172.16.0.1/24
Broadcast address is 255.255.255.255
Address determined by setup command
MTU is 4470 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Outgoing access list is not set
Inbound access list is not set
Proxy ARP is enabled
Local Proxy ARP is disabled
Security level is default
Split horizon is disabled
ICMP redirects are always sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is enabled
IP fast switching on the same interface is disabled
IP Flow switching is disabled
Configuration du routeur R6
R6(config)#interface a1/0
R6(config-if)#no ip address
R6(config-if)#no shutdown
R6(config-if)#exit
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 3
R6(config)#interface a1/0.1 point-to-point
R6(config-subif)#ip address 172.16.0.2 255.255.255.0
R6(config-subif)#pvc 1/100
R6(config-if-atm-vc)#protocol ip 172.16.0.1 broadcast
R6(config-if-atm-vc)#encapsulation aal5snap
Diagnostique
R6#show ip interface
FastEthernet0/0 is administratively down, line protocol is
down
Internet protocol processing disabled
ATM1/0 is up, line protocol is up
Internet protocol processing disabled
ATM1/0.1 is up, line protocol is up
Internet address is 172.16.0.2/24
Broadcast address is 255.255.255.255
Address determined by setup command
MTU is 4470 bytes
Helper address is not set
Directed broadcast forwarding is disabled
Outgoing access list is not set
Inbound access list is not set
Proxy ARP is enabled
Local Proxy ARP is disabled
Security level is default
Split horizon is disabled
ICMP redirects are always sent
ICMP unreachables are always sent
ICMP mask replies are never sent
IP fast switching is enabled
IP fast switching on the same interface is disabled
IP Flow switching is disabled
Définition des routes
Ajoutez ensuite une route statique pour aller vers les sous réseaux de part et d’autre.
R5(config)#ip route 192.168.2.0 255.255.255.0 172.16.0.2
R6(config)#ip route 192.168.1.0 255.255.255.0 172.16.0.1
Test de fonctionnement
R6#ping 192.168.1.254 source 192.168.2.254
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 4
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.254, timeout is 2
seconds:
Packet sent with a source address of 192.168.2.254
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max =
92/156/188 ms
R5#ping 192.168.2.254 source 192.168.1.254
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.2.254, timeout is 2
seconds:
Packet sent with a source address of 192.168.1.254
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max =
100/231/276 ms
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 5
La diffusion et la multidiffusion est utilisée le plus souvent pour établir des liaisons point
à point et des liaisons points à multipoint entre un poste client et plusieurs stations du
réseau. Dans le réseau ATM la diffusion et la multidiffusion peut être établie dans une
liaison point à point ou dans une liaison point à multipoint. L’intérêt d’avoir une liaison point
à multipoint est de gérer le trafic au niveau d’un seul site par exemple.
1- Architecture
2- Configuration des ports du commutateur
- Port 1 : VPI 1 et VCI 100 (PVC= 1/100 pour aller vers R2)
- Port 1 : VPI 3 et VCI 300 (PVC= 3/300 pour aller vers R3)
- Port 2 : VPI 2 et PVC 200 (PVC=2/200)
- Port 3 : VPI 4 et VCI 400 (PVC=4/400)
LAB 2 : ATM CONNEXION POINT A MULTIPOINT
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 6
3- Configuration des interfaces des routeurs
o Configuration des interfaces du routeur R1
R1>en
R1#conf t
R1(config)#interface a1/0
R1(config-if)#no ip address
R1(config-if)#no shutdown
R1(config-if)#exit
R1(config)#interface a1/0.1 point-to-point
R1(config-subif)#ip address 172.16.1.1 255.255.255.0
R1(config-subif)#pvc 1/100
R1(config-if-atm-vc)#protocol ip 172.16.1.2 broadcast
R1(config-if-atm-vc)#encapsulation aal5snap
R1(config-subif)#exit
R1(config)#interface a1/0.2 point-to-point
R1(config-subif)#ip address 172.16.2.1 255.255.255.0
R1(config-subif)#pvc 3/300
R1(config-if-atm-vc)#protocol ip 172.16.2.2 broadcast
R1(config-if-atm-vc)#encapsulation aal5snap
R1(config)#interface fa0/0
R1(config-if)#ip address 192.168.1.254 255.255.255.0
R1(config-if)#no shutdown
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 7
o Configuration des interfaces du routeur R2
R2#conf t
R2(config)#interface a1/0
R2(config-if)#no ip address
R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#interface a1/0.1 point-to-point
R2(config-subif)#ip address 172.16.1.2 255.255.255.0
R2(config-subif)#pvc 2/200
R2(config-if-atm-vc)#protocol ip 172.16.1.1 broadcast
R2(config-if-atm-vc)#encapsulation aal5snap
R2(config-subif)#exit
R2(config)#interface fa0/0
R2(config-if)#ip address 10.10.1.254 255.255.255.0
R2(config-if)#no shutdown
o Test de connectivité
R2#ping 172.16.1.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.1.1, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max =
144/240/284 ms
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 8
o Diagnostique
R2#show atm pvc
VCD / Peak
Avg/Min Burst
Interface Name VPI VCI Type Encaps SC Kbps
Kbps Cells Sts
1/0.1 1 2 200 PVC SNAP UBR 155000
UP
o Configuration des interfaces du routeur R3
R3#conf t
R3(config)#interface a1/0
R3(config-if)#no ip address
R3(config-if)#no shutdown
R3(config-if)#exit
R3(config)#interface a1/0.1 po
R3(config)#interface a1/0.1 point-to-point
R3(config-subif)#ip address 172.16.2.2 255.255.255.0
R3(config-subif)#pvc 4/400
R3(config-if-atm-vc)#protocol ip 172.16.2.1 broadcast
R3(config-if-atm-vc)#encapsulation aal5snap
R3(config)#interface fa0/0
R3(config-if)#ip address 10.10.1.254 255.255.255.0
R3(config-if)#no shutdown
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 9
4- Définition de routes
Sur R1
R1(config)#ip route 10.10.1.0 255.255.255.0 172.16.1.2
R1(config)#ip route 10.10.2.0 255.255.255.0 172.16.2.2
Sur R2
R2(config)#ip route 192.168.1.0 255.255.255.0 172.16.1.1
Sur R3
R3(config)#ip route 192.168.1.0 255.255.255.0 172.16.2.1
5- Test
R2#ping 192.168.1.254 source 10.10.1.254
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.254, timeout is 2
seconds:
Packet sent with a source address of 10.10.1.254
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max =
452/521/548 ms
//
R3#ping 192.168.1.254 source 10.10.2.254
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 192.168.1.254, timeout is 2
seconds:
Packet sent with a source address of 10.10.2.254
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 10
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max =
316/410/544 ms
#║
R1#ping 10.10.1.254 source 192.168.1.254
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.1.254, timeout is 2
seconds:
Packet sent with a source address of 192.168.1.254
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max =
156/300/532 ms
R1#ping 10.10.2.254 source 192.168.1.254
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.10.2.254, timeout is 2
seconds:
Packet sent with a source address of 192.168.1.254
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max =
252/270/300 ms
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 11
Rôle d’un pont ATM
La technologie LANE (LAN Emulator) permet à un réseau ATM de se comporter comme
un réseau LAN. L’objectif est de passer d’un réseau LAN ver un réseau ATM en toute
douceur. Cette migration plein d’issue n’est possible que si on utilise équipement de liaison
du réseau ATM. Il s’agit du pont ATM. En effet un pont ATM permet d’utiliser les services
offerts dans un réseau LAN dans un réseau ATM.
1- Architecture
1- Configuration du pont ATM
Le pont ATM a une interface Ethernet qui le relie au réseau Ethernet et une interface ATM
qui le relie au réseau ATM avec le PVC 2/100
LAB 3 : INTRECONNEXION ENTRE UN RESEA ATM ET UN RESEAU ETHERNET VIA UN PONT ATM
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 12
2- Configuration du routeur R2
R2>en
R2#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R2(config)#interface a1/0
R2(config-if)#no ip address R2(config-if)#no shutdown
R2(config-if)#exit
R2(config)#interface a1/0.1 point-to-point
R2(config-subif)#ip address 172.16.0.1 255.255.255.0
R2(config-subif)#atm route-bridged ip
R2(config-subif)#atm route-bridged ip
R2(config-subif)#pvc 2/100
R2(config-if-atm-vc)#exit
R2(config-subif)#no shutdown
3- Configuration du routeur R1
R1>en
R1#conf t
Enter configuration commands, one per line. End with CNTL/Z.
R1(config)#interface fa0/0
R1(config-if)#ip address 172.16.0.2 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#
*ay 10 12:19:09.047: %LINEPROTO-5-UPDOWN: Line protocol on
Interface FastEthernet0/0, changed state to up
R1(config)#interface fa0/1
R1(config-if)#ip address 192.168.1.254 255.255.255.0
R1(config-if)#no shutdown
R1(config-if)#
*May 10 12:19:57.211: %LINK-3-UPDOWN: Interface
FastEthernet0/1, changed state to up
4- Test de bon fonctionnement
R2 ->R1 (Ethernet)
Sending 5, 100-byte ICMP Echos to 172.16.0.2, timeout is 2
seconds:
.!!!!
Success rate is 80 percent (4/5), round-trip min/avg/max =
348/387/408 ms
R2#ping 172.16.0.2
Réseaux Hauts Débits ATM EC2LT-Dakar
Yvan KALIA Master 2 Réseaux/Télécoms Page 13
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.0.2, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max =
380/400/432 ms
R1 -> vers réseau TAM
R1#ping 172.16.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 172.16.0.1, timeout is 2
seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max =
264/300/404 ms
Testez la liberté