Upload
kokkera-sankara-rao
View
345
Download
4
Embed Size (px)
Citation preview
Slide 1
PIPING
Slide 2
TRAINNING OF PIPING- STEEL PIPE STANDARD- STAINLESS STEEL PIPE- COPPER PIPE
- CENTRIFUAL PUMP, GEAR PUMP- SCREW PUMP, PISTON PUMP- EJECTOR PUMP, MONO PUMP
PIPE
FLAGE
PUMP
VALVE
GASKET
Slide 3
PIPE
1. STEEL PIPE STANDARD
■ SGP (Steel Gas Pipe)
■ STPG (Steel Tubing Piping General)
■ STS (Steel Tubing Special)
■ STPY (Steel Tubing Piping Yosetsu)
■ STPT (Steel Tubing Piping High Temperature)
Slide 4
SGP ( Steel Gas Pipe)
• Carbon steel pipe for ordinary piping
• Used for the pipings for conveying system, water, oil, gas, air, etc.
Letter symbol of
gradeDivision
Chemical
Composition (%)
Tensile Strength
(kgf/mm²)
Elongation(%)
P S Longitudinal Transverse
SGP
Black Pipe
(without zinc coating) 0.040
max.0.040 max.
30 kgf/mm² 30 min. 25min.
Galvanized Pipe (with zinc coating)
Slide 5
STPG (Steel Tubing Piping General)
• Carbon steel pipe for pressure service.
• Used for pressure service at an approximate maximum temperature of 350ºc
Letter symbol
of grade
Chemical
Composition (%)
Tensile Strength
(kgf/mm²) [N/mm²]
Yield Point or Proof Stress
(kgf/mm²) [N/mm²]
Elongation(%)
Pressur
e(Kg/Cm²)
C Si Mn P S
Longitudinal
Transverse
STPG
38
0.25 0.35 0.30-0.90
0.04 0.04 38[373] 22[216] 28 23 Sched.40>50
STPG
42
0.30 0.35 0.30-0.10
0.04 0.04 42[412] 25[245] 24 19 Sched.80>70
Slide 6
STS (Steel Tubing Special)
• Carbon steel pipe for pressure service.
• Used for high pressure service at an approximate maximum temperature of 350ºc
Letter symbol of grade
Chemical
Composition (%)
Tensile Strength
(kgf/mm²) [N/mm²]
Yield Point or Proof Stress (kgf/mm²) [N/mm²]
Elongation(%)
C Si Mn P S Longitudinal
Transverse
STS38 0.25 0.01-0.35
0.30-
1.10
0.035 0.035 38[373] 22[216] 28 23
STS42 0.30 0.01-0.35
0.30- 1.40
0.035 0.035 42[412] 25[245] 24 19
STS49 0.33 0.01-0.35
0.30- 1.50
0.035 0.035 49[481] 28[275] 22 17
Slide 7
STPY (Steel Tubing Piping Yosetsu)
• Electric arc welded carbon steel pipe
• Used for piping for stream, gas, water, air, etc. of comparatively low working pressure
Letter symbol of grade
Chemical
Composition (%) Tensile Strength
(kgf/mm²) [N/mm²]
Yield Point or Proof Stress (kgf/mm²)
[N/mm²]
Elongation(%)
C P S Transverse
STPY41 0.25 0.040 0.040 41[402] 23[226] 18
Slide 8
STPT (Steel Tubing Piping High Temperature)
• Carbon steel pipe for temperature service.
• Mainly used for piping at a temperature over 350ºc
Letter symbol of grade
Chemical
Composition (%)
Tensile Strength
(kgf/mm²) [N/mm²]
Yield Point or Proof Stress
(kgf/mm²) [N/mm²]
Elongation(%)
C Si Mn P S Longitudinal
Transverse
STPT38 0.25 0.01-0.35
0.30-
0.90
0.035 0.035 38[373] 22[216] 28 23
STPT42 0.30 0.01-0.35
0.30- 1.00
0.035 0.035 42[412] 25[245] 24 19
STPT49 0.33 0.01-0.35
0.30- 1.00
0.035 0.035 49[481] 28[275] 22 17
Slide 9
STPT (Steel Tubing Piping High Temperature)
• Steel Mechanical properties
Mn ( maganese) To add up to 1.8% to improve mechanical properties .
Si (silicon) To add 0.5~3.5% to increase strength and hardness.
Ni (nickel) To 3~3.75% to produce a finer gained material with increased strength and erosion resistance.
Cr (chromium) Tends to increase grain size and create hardness, but improves resistance to erosion and corrosion.
Slide 10
PIPE
2. STAINLESS STEEL PIPE
■ SUS - TP (Steel Use Stainless Tube Pipe)
■ SUS - TPY (Steel Use Stainless Tube Pipe Y)
■ SUS ERW (Stainless Steel Electric Resistance Welding )
3. COPPER PIPE
4. AL-BRASS PIPE AND CU-NI PIPE
Slide 11
FLANGE
• Connecting pipes and valves are used for the arrangement of pipes for vapour, air, oil, water, etc.
• Nominal Pressure
- The ratings of nominal pressures shall be in accordance with Attached Table.
Slide 12
TYPES OF FLANGES
1. Loose type flanges• Lap joint type flanges - The flange to be used in combination with stub end
• Slip-on type flanges- The flange which is screwed in or inserted into a tube and attached
by welding
Slide 13
TYPES OF FLANGES
2. Integral type flange- The flange casted or forged integrally with tube
or the flange so welded by complete joint penetration that the flange and the tube become integral.
3. Optional type of flange- The flange attached to the tube by welding.- This flange must be calculated as the integral
type flange.
Slide 14
SLIP-ON WELDING STEEL PIPE FLANGE – 5Kg/cm²
Slide 15
SLIP-ON WELDING STEEL PIPE FLANGE – 10Kg/cm²
Slide 16
SLIP-ON WELDING STEEL PIPE FLANGE – 16Kg/cm²
Slide 17
SLIP-ON WELDING STEEL PIPE FLANGE – 30Kg/cm²
Slide 18
Welding Neck Flanges
• The welding neck flange is normally referred to as the"high hub“ flange. It is designed to transfer stresses tothe pipe, there by reducing high stress concentrationsat the base of the flange. The welding neck flange isthe best designed butt-welded flange of those currentlyavailable because of its inherent structural value. It isexpensive because of the designed
Welding Neck Flanges
Slide 19
Threaded (Screwed) Flanges
• The threaded flange is similar to the slip-on flange, out the bore is threaded. Its chief merit is that it can be assembled without welding, explaining its use in low pressure services at ordinary atmospheric temperatures and in highly explosive areas where welding create a hazard.
Threaded(Screwed) Flanges
Slide 20
Blind Flanges
• The blind flange is a flange without a bore. It is used toclose off the ends of a piping system and/or a pressurevessel opening. It also permits easy access to the interior of a line or vessel once it has been sealed andmust be reopened.
Blind Flanges
Slide 21
Socket Welding Flanges
• The socket welding flange is similar to a slip-on flange except it has a bore and a counter bore dimension. The counter bore is slightly larger than the O.D. of the matching pipe, allowing the pipe to be inserted into the flange similar to a slip-on flange. The diameter of the smaller bore is the same as the I.D. of the matching pipe.A restriction is built into the bottom of the bore which sets as a shoulder for the pipe to rest on. This eliminates any restriction in flow when using a socket welding flange.
Socket Welding Flanges
Slide 22
Flange Types
Semi-Confined Gasket• Depth of female (recessed) face normally equal to or less than height of male (raised) face, to prevent metal-to-metal contact during gasket compression• Recessed O.D. normally is not more than 1/16“ larger than the O.D. of the male face • Joint must be pried apart for disassembly
Unconfined Gasket• Mating faces of both flanges are flat• Gasket may be ring type, or full face, which coversthe entire face both inside and outside the bolts
Slide 23
Flange Types
Unconfined Gasket• Mating face is flat, but the area inside the bolt holes is raised 1/16" or 1/4"• Gasket is usually ring type, entirely within bolts• Flanges may be disassembled easily without springing the flange
Fully Confined Gasket• Groove depth is equal to or less than tongue height• Groove usually not over 1/16" wider than tongue• Gasket dimensions will match tongue dimensions• Joint must be pried apart for disassembly
Slide 24
Flange Types
Also Called "API Joint"• Both flange faces have matching flat-bottomed grooves with sides tapered from the vertical at 23°• Gasket seats on flat section of flange between bore and ring joint groove • Garlock spiral wound gaskets can replace solid metal ring gaskets
Fully Confined Gasket• One flange face is flat, the other is recessed• For applications requiring accurate control of gasket compression• Only resilient gaskets are recommended - spiralwound, hollow metal O-ring, pressure-actuated, and metal-jacketed gaskets
Slide 25
GASKET
• Used for pipe flanges delivering fluids such as steam, water and oil.
1. Flat Nom-Metallie and Metal Clad or Jacketed Gaskets
2. Spiral Wound Gaskets
3. Flat Metal Gaskets
4. Ring Joint
5. Oval Ring Joint
Slide 26
GASKET
Slide 27
TYPES & TYPE SYMBOLS OF GASKET
• Basic form (A)
- Plate form gasket body alone which has been made from endless strip of corrugated thin metal sheet and overlapped asbestos paper by spot welding at several points of the metal sheet at both its initial end and terminal.
• With inner ring (B)
- Basic form equipped with an inner ring.
Slide 28
TYPES & TYPE SYMBOLS OF GASKET
• With outer ring (C)
- Basic from equipped with an outer ring.
• With inner and outer rings (D)
- Basic form equipped with both an inner ring and an outer ring.
Slide 29
VALVE
• A valve is a device attached to a pipe or a tube which controls the flow of air or liquid through the pipe or tube.
• Valves are provided in a piping system to regulate or stop the liquid flow.
• Various types exist with their associate particular function or adventages.
Slide 30
STRUCTURE OF VALVE
BODY SEAT RING
BODY
STEM
HAND WHEEL
NAME PLATE
DISC
BONNET
DISC NUT
YOKE SLEEVE
PACKING
PACKING RING
Slide 31
STRAIGHT ANGLE
1. GLOBE /ANGLE VALVE - A glove valve has a somewhat spherical body enclosing the valve seat and
valve disc. - The valve disc and seat are a prefect match and may be flat or, more
commonly, mitred.- Glove valves exist in a right-angled form where the inlet and exit flanges are
at 90º to each other.
Slide 32
2. GATE VALVE
- A gate valve should be fully open or closed. (it is not suitable for flow control)
- When open it provides a clear full-bore internal passage for the liquid since the valve or gate is raised clear.
- The gate may be parallel or wedge-shaped in section fitting against a matching seat.
Slide 33
3. BUTTERFLY VALVE
• A butterfly valve is a type of flow control device, typically used to regulate a fluid flowing through a section of pipe.
• The plate has a rod through it connected to a handle on the outside of the valve. Rotating the handle turns the plate either parallel or perpendicular to the flow.
Slide 34
BUTTERFLY VALVE -1
Flange TypeLug Type Wafer Type
Slide 35
BUTTERFLY VALVE -2
Eccentric Type Concentric Type
- Eccentric Type
- Concentric Type
- Double eccentric Type
Slide 36
BUTTERFLY VALVE
Double-eccentric type
Slide 37
CLOSE OPEN
4-1. BALL VALVE (2-WAY)
• which is good for on/off control.
Slide 38
4-2. BALL VALVE (3-WAY)
L-Type T-Type
Slide 39
5. NIDDLE VALVE
• A good general purpose needle valve for fine shots and small beads of medium viscosity materials.
• The valve is available with stainless steel wetted chambers suitable for UV cure dispensing, plastic chambers for anaerobic dispensing and aluminum as a standard configuration for dispensing silicones, grease and lubricants.
Slide 40
6. CHECK VALVE
• Chest valve or Non-return valve, allows the fluid to pass in one direction only.
• Protection of any item of equipment that can be affected by reverse flow, such as flow meters, strainers and control valves.
• Prevention of flooding, reverse flow on system shutdown an flow under gravity. Swing check valveCheck valve
Slide 41
7. STORM VALVE
• Scuppers and sanitary discharges as closing appliances. • Set in the annulus between the drill pipe and the well casing,
the actuator being designed to close the valve upon initial axial movement of the upper portion of the drill pipe
• Become disengaged from the lower portion of the set drill pipe allowing the remaining surface suspended drill pipe and actuator to be retrieved as in the case of a floating drill ship or set aside for reconnection and reopening of the storm valve after a storm has passed.
Slide 42
STORM VALVE
Angle TypeVertical Type
Slide 43
8. QUICK CLOSING VALVE• Oil tank suction valves are
arranged for rapid closing from a remote point by the use of quick-closing valves.
Slide 44
9. SEUT VALVE
Slide 45
• The insert(valve disc) (1) is placed inside the valve body (6) with the disc stopper (2) on the left-hand disc, using the ”hook” on the end of the spanner. The discs are tightened against the valve-seating by turning the tightening nut (3) towards you. The tightening moment for the discs depend on the pressure on the discs. To remove insert (1) with the disc-stopper on left-hand discs, the tightening nut is turned from you. The “hook” on the end of the spanner is used for lifting insert (1) out of the valve body. When closing the valve body, the cover (4) is brought into position and coverbolt-nuts (5) are turned down by hand, making sure that the cover is planned against the cover-seating. Turn each coverbolt-nut one half turn at a time until sufficient pressure is reached. To remove cover (4), loosen coverbolt-nut (5) where the spring is placed first, then loosen opposite nut. Be sure the jointing is clear of valve-seating before cover is swing aside. When discs (1) are inserted in valve-body, cover (4) to be kept open, making it possible to inspect valve-body for any leakage. When cover (4) is tightened down and discs (1) are removed from valve-body (6), discs (1) should be stored as close to the valve as possible, preventing any misunderstanding whether discs are inside the valve-body or not. The jointings/gaskets should be inspected before use.
Slide 46
10. HOSE VALVE
• Hose valves have heavy rough brass body with machined brass vandal-resistant lock shield bonnet and are furnished with a removable wheel handle.
• Hose valve covering helps prevent damage to delicate tank or vessel linings, machines, floors, and protects the valve.
• Innovative ball-and-seat design provides a tight shut-off to minimize leakage.
ANGLE V/V
Slide 47
HOSE VALVE
Slide 48
11. COCK
• Colloquial term for a small valve.
Slide 49
12. HYDRAULIC VALVE
• Diaphragm valve
• Diaphragm valves are used with low viscosity fluids and are available in several configurations for UV cure dispensing, anaerobic dispensing, cyanoacrylate dispensing, solvent dispensing and volatile liquid dispensing.
• Diaphragm valves offer the highest temperature/pressure ratings.
Slide 50
HYDRAULIC VALVE