Description Qty.

1 703966 Scaled Drill 2.5 × 450mm, AO 2

2 700355 Calibrated Drill Bit 2.5 × 230mm, AO 2

3 700351 Calibrated Drill Bit 2.5 × 180mm, AO 2

4 700353 Drill Bit 3.5 × 180mm, AO 1

5 702811 Countersink 6.0 × 100mm, AO 1

6 702804 Tap 3.5 × 180mm, AO 1

7 702418 Double Drill Guide 2.5/3.5mm 1

8 703962 Washer Pick-Up Stand 1

9 703961 Spiked Disk for 3.5mm Spiked Inserter 1

10 703960 Spiked Screw Inserter for 3.5mm Screws 1

Description Qty.

11 703964 Plate Screw Inserter for 3.5mm Screws 1

12 703965 Drill Sleeve, 2.5mm, for 3.5mm Screws 1

13 702427 Small T-Handle, AO 1

14 703967 Screwdriver Hex 2.5 × 425mm 1

15 703968 Screwdriver Hex 2.5 × 342mm, AO 1

16 703973 Drill Sleeve, 3.2mm, for 4.5mm Screws 1

17 702428 Small Teardrop Handle, AO(Alt. 702848 Canevasit Handle) 1

18 702861 Screwdriver Holding Sleeve for 3.5mm Screws 1

19 702851 Screwdriver Hex 2.5 × 165mm, AO 1

Description Qty.

20 702842 Screwdriver Hex 2.5 × 280mm(Alt. 702845 Canevasit Handle)

1

21 702876 Depth Gauge 0-110mm for 3.5mm Screws 1

22 703976 Angled Depth Gauge 1

23 703974 Scaled Drill, 3.2 × 450mm, AO 1

24 703975 Screwdriver Hex 3.5 × 342mm, AO 1

25 703972 Spiked Screw Inserter for 4.5mm Screws 1

1

2

3

Tray Layout Sheet – PRO Basic Instruments Top Tray

4

7

6

8 9

10

12

13

15

16

17

14

18

19

20

21

22

24

23

25

11

5

Tray Layout Sheet – PRO Basic Instruments Bottom Tray

1

2

4

3

76

8

9

10

12

13

15

16

17

14

18

19

20

21

22

24

23

11

5

Description Qty.

1 700356 Calibrated Drill Bit 3.2 × 180mm, AO 2

2 700357 Calibrated Drill Bit 3.2 × 230mm, AO 2

3 700354 Drill Bit 4.5 × 180mm, AO 2

4 702812 Countersink 8.1 × 100mm, AO 1

5 702806 Tap 4.5 × 180mm, AO 1

6 702807 Tap 6.5 × 180mm, AO 1

7 390084 Reduction Pin 5.0 × 180mm, AO 1

8 390083 Reduction Pin 5.0 × 50mm, AO 1

9 702912 Straight Ball Spike, AO 1

10 702417 Double Drill Guide 3.2/4.5mm 1

Description Qty.

11 702923 Spiked Disk 2

12 703963 Handle for Plate Insertion 1

13 703958 Angled Ball Spike 15° 1

14 703959 Angled Ball Spike 30° 1

15 702911 Straight Ball Spike(Alt. 702847 Canevasit Handle) 1

16 702877 Depth Gauge 0-150mm for 4.5mm Screws 1

17 702429 Large Teardrop Handle, AO(Alt. 702849 - Canevasit Handle) 1

18 702862 Screwdriver Holding Sleeve for 4.5/6.5mm Screws 1

Description Qty.

19 702853 Screwdriver Hex 3.5 × 165mm, AO 1

20 702843 Screwdriver Hex 3.5 × 300mm (Alt. 702846 Canevasit Handle)

1

21 703970 Plate Bender 1

22 702902 Bending Iron 1

23 703969 Plate Bending Holder 1

24 703971 Bending Stick 2

A surgeon must always rely on his or her own professional clinical judgment when deciding whether to use a particular product when treating a particular patient. Stryker does not dispense medical advice and recommends that surgeons be trained in the use of any particular product before using it in surgery.The information presented is intended to demonstrate the breadth of Stryker product oerings. A surgeon must always refer to the package insert, product label and/ or instructions for use before using any Stryker product. Products may not be available in all markets because product availability is subject to the regulatory and/or medical practices in individual markets. Please contact your Stryker representative if you have questions about the availability of Stryker products in your area. Stryker Corporation or its divisions or other corporate aliated entities own, use or have applied for the following trademarks or service marks: PRO, Stryker. All other trademarks are trademarks of their respective owners or holders.Content ID: PRO-TLC-2, 05-2015 (former Literature Number: 2013-017-PEL) Copyright © 2015 Stryker

325 Corporate Drive Mahwah, NJ 07430 t: 201 831 5000www.stryker.com

For the full content set list refer to: Set Configuration – PRO Basic Instruments Complete