USER MANUAL 2AMDI511VPVRDBS - nectogroup.com · The maximum current absorbed by 0-10V dimmer ... a signal in direct or alternating ... In order to install the app on your Apple or

Necto Group S.r.l. 35127 Padova - Via Canada, 8 - ITALY - T +39 049 8791001 | F +39 049 8791002 | Email [email protected] pag. 1

USER MANUAL 2AMDI511VPVRDBS

SUBJECT INDEX:

DESCRIPTION

TECHNICAL SPECIFICATION

DEVICE POWER SUPPLY AND CONNECTION TO THE LED MODULE

OPERATION MODES

LINEAR POTENTIOMETER MODE 100KOHM

MODE 0-10V/1-10V PASSIVE

PUSH MODE

DALI MODE

BLUETOOTH MODE + PUSH

PARAMETERS CONFIGURATION

User ManUal 2aMDI511VPVrDBs


DIMMER MONOCANALE MULTIPROTOCOLLO C.V. BLUETOOTH IoT LightSINGLE CHANNEL MULTIPROTOCOL DIMMER C.V. BLUETOOTH IoT Light

Dimmer Mono canale con Uscita in Tensione PWM. Range di alimentazione: 8-53V DC. Uscita in Tensione PWM 8-53V DC con corrente da 0A a 12A (576W a 48V DC). Controllabile tramite app Android/iOS IOT LIGHT. Per impostare il fade e la curva logaritmica/lineare di uscita occorre dotarsi di interfaccia 2AMIN4030000N venduta separatamente, le modalità di funzionamento vengono riconosciute e impostate automaticamente dal dispositivo senza bisogno di interfaccia esterna. Vedi manuale d’uso.

Mono channel Dimmers with Output Tension PWM. Input Range: 8-53V DC.Output Tension PWM 8-53V DC with current from 0A to 12A (576W at 48V DC). Controllable with Android/iOS app IOT LIGHT. In order to set the fade output and the logarithmic or linear output you will need the 2AMIN4030000N interface sold separately, the other working modes are automatically detected by the device. Please refer to user manual.

INGRESSI DI CONTROLLO - CONTROL INPUTS

DALI 0-10V;1-10VPUSH NO

(INSULATED)BLUETOOTH LE

POTENZIOMETRO LINEARE 100KLINeaR POTeNTIOmeTeR

X1 X1 X1 X1 X1

USCITA SYNCROOUTPUT SYNCRO

CORRENTE MAX IN USCITA (*)maX OUTPUT CURReNT

PWM X1 12A

CARATTERISTICHE TECNICHETeCHNICaL NOTeS

- Dimmer Mono canale con Uscita in Tensione PWM.- Range di alimentazione: 8-53V DC.- Uscita in Tensione PWM 8-53V DC con corrente da 0A a 12A (576W a 48V DC).- Controllabile tramite app Android/iOS IOT LIGHT.- Ingressi di Controllo: Pulsante isolato x1, DALI x1, Potenziometro Lineare 100K x1, 0-10V Passivo x1, 1-10V Passivo x1, Bluetooth LE x1.- Uscite di sincronia: PWM x1. - Circuito Stampato UL.- Classe di protezione: IP20. - Dimensioni Standard 40x80x24.45 mm.- Dimensioni con Accessori 40x100x24.45 mm.- Protezione da inversione di polarità. - Protezione circuito aperto.- Protezione da picchi tensione. - Protezione da sovratemperatura.

- mono channel Dimmers with Output Tension PWm.- Input Range: 8-53V DC.- Output Tension PWm 8-53V DC with current from 0a to 12a (576W at 48V DC).- Controllable with android/iOS app IOT LIGHT.- I nput Controls: Insulated Push button x1, DaLI x1, Linear Potentiometer 100K x1,

0-10V Passive x1, 1-10V Passive x1, Bluetooth Le x1.- Output Sync: PWm x1. - Printed Circuit UL.- Protection Class: IP20. - Standard Dimension 40x80x24.45 mm.- Dimension with accessories 40x100x24.45 mm.- Reverse polarity protection. - Open circuit protection.- Surge voltage protection. - Over temperature protection.

PULSANTE N/O ISOLATON/O insulated switch



CODICECODe

TENSIONEIN INGRESSO

INPUT VOLTaGe

CORRENTEUSCITA (MAX)(maX) OUTPUT

CURReNT

n. CANALIIN USCITAn. OUTPUT CHaNNeLS

POTENZA MAXIN USCITA

maX OUTPUT POWeR

INGRESSIDI CONTROLLO

CONTROL INPUTS

SCATOLACaSe

DIM.DIm.

2AMDI511VPVRDBS 8-53V DC 12A 1 576W A 48V DC

PULSANTE ISOLATO X1DALI X1

POTENZIOMETRO LINEARE 100K X10-10V PASSIVO X11-10V PASSIVO X1BLUETOOTH LE X1

SI 40X80 mmh 24,45 mm



POWER SUPPLY CONNECTION DIAGRAM AND LED 2AMDI511VPVRDBS - FIGURE N. 1

The 2AMDI511VPVRDBS dimmer has to be powered according to the polarity showed in FIG. 1through the DC IN (+ and -) terminals.In case the power supply polarity is inverted no damage will be caused to the device .The LED (LED PWR) positioned on the circuit board indicates the presence of power supply.The LED (LED DIM) shows the dimming level of the output.The LED load connection has to be made by using the OUT (L+ and L-) terminals.

DEVICE POWER SUPPLY AND CONNECTION TO THE LED MODULE



POTENTIOMETER WIRING 2AMDI511VPVRDBS - FIGURE N. 2

In order to activate this mode of control/operation just connect a linear potentiometer of 100 Kohm between the D+and D- inputs and disconnect the remaining inputs.By default, the dimming curve follows a logarithmic trend proportional to the resistance value set by thepotentiometer.A resistance value of less than 5 Kohm is interpreted as load off.The maximum brightness value is reached by exceeding the value of 95 Kohm.In case the potentiometer is disconnected, the dimmer sets the output to the saved level (see preset levelchange).The preset value is zero by default.On the first run in this mode it could be necessary to set the input to a value greater than 50% (55K or higher on DD+ input) in order to configure the dimmer to the potentiometer mode.

*This setting can be configured through the interface cod. 2AMIN4030000N ATTENTION IN THIS MODE THE BLUETOOTH CONTROL IS FORBIDDEN

OPERATION MODES

LINEAR POTENTIOMETER MODE 100KOHM



WIRING 0-10V 2AMDI511VPVRDBS - FIGURE N. 3

In order to activate this mode of control/operation just connect the active control signal of 0-10V/1-10V betweenthe D+ and D- inputs (being careful to observe the correct polarity) and disconnect the remaining control signals.The maximum current absorbed by 0-10V dimmer interface is 0,1 mA.By default, the dimming curve follows a logarithmic trend proportional to the control voltage. A voltage value of lessthan 1V is interpreted as load off.In case the 0-10V/1-10V signal is disconnected, the dimmer sets the output to the saved level (see preset levelchange). The preset value is zero by default.On the first run in this mode it could be necessary to set the input to a value greater than 50% (5V or higher on DD+ input) in order to configure the dimmer to the 0-10V/1-10V mode.*This setting can be configured through the interface cod. 2AMIN4030000N ATTENTION IN THIS MODE THE BLUETOOTH CONTROL IS FORBIDDEN

MODE 0-10V/1-10V PASSIVE



WIRING BUTTON 2AMDI511VPVRDBS - FIGURE N. 4

In order to activate this mode of control/operation it is necessary to remove any control signals from the D + and Dinputsand connect between the DALI/P1 and DALI/P2 inputs, a signal in direct or alternating voltage(DC voltage range:10÷265V, AC 12÷265Vac 50÷65Hz) interrupted by a normally open button (N.O.).No polarization is needed for the input signal.The maximum current absorbed by the PUSH interface is about 2mA.The dimmer saves the output position in order to restore the set level in case of power failure (preset).

PUSH interface operation

Single Click (rapid press (<1sec))- Turns on or off the output (ON/OFF).

Double Click (rapid press (<1sec))- Sets maximum brightness (output= 100%)

Long Press (long press (>1sec))- If the dimmer is in OFF position, it sets the output to the minimum value (default= 1%)- If the dimmer is in ON position, the long press enables the output dimming (up/down).

PUSH MODE



DALI 2AMDI511VPVRDBS WIRING - FIGURE N. 5

In order to activate this mode of control/operation it is necessary to shortcircuit the D+ and D- inputs and connectthe DALI bus between the DALI/P1 and DALI/P2 inputs.On the first reception of a properly formatted DALI package the dimmer is configured in DALI mode. Onceconfigured in DALI mode and disconnected from the DALI bus the dimmer switches to the POWER ON LEVELmode set through DALI bus.The maximum current absorbed by the DALI bus is about 2mA.

ATTENTION IN THIS MODE THE BLE (Bluetooth) CONTROL IS FORBIDDEN

Below you can find the implemented standard commands:DIRECT ARC POWEROFFUPDOWNSTEP UPSTEP DOWNRECALL MAX LEVELRECALL MIN LEVELSTEP DOWN AND OFFON AND STEP UPGO TO SCENE (0-15)RESETSTORE ACTUAL LEVEL IN THE DTRSTORE THE DTR AS MAX LEVELSTORE THE DTR AS MIN LEVELSTORE THE DTR AS SYSTEM FAILURE LEVELSTORE THE DTR AS POWER ON LEVELSTORE THE DTR AS FADE TIMESTORE THE DTR AS FADE RATESTORE THE DTR AS SCENE (0-15)REMOVE FROM SCENE (0-15)ADD TO GROUP (0-15)

DALI MODE



REMOVE FROM GROUP (0-15)STORE DTR AS SHORT ADDRESSQUERY STATUSQUERY BALLASTQUERY LAMP POWER ONQUERY LIMIT ERRORQUERY RESET STATEQUERY MISSING SHORT ADDRESSQUERY VERSION NUMBERQUERY DEVICE TYPEQUERY PHISICAL MINIMUM LEVELQUERY POWER FAILUREQUERY CONTENT DTR1QUERY CONTENT DTR2QUERY ACTUAL LEVELQUERY MAX LEVELQUERY MIN LEVELQUERY POWER ON LEVELQUERY SYSTEM FAILURE LEVELQUERY FADE TIME/FADE RATEQUERY SCENE LEVEL (0-15)QUERY GROUPS (0-7)QUERY GROUPS (8-15)QUERY RANDOM ADDRESS HQUERY RANDOM ADDRESS MQUERY RANDOM ADDRESS L



BLE 2AMDI511VPVRDBS WIRING - FIGURE N. 6

In order to activate this mode of control/operation it is necessary to install the Necto Group App on the Android oriOS device that you want to use for the 2AMDI511VPVRDBS dimmer control and disconnect any 0-10V (1-10V) inputs orpotentiometer connected to the dimmer.The implemented features are:Switching on and off and the brightness level control of each individual light point.Ability to group together and control several light points with just a simple command.Creation and recall of your favourite lighting sceneries.The system management from a single simplified user interface.

THE BLUETOOTH LE CONNECTION DOES NOT REQUIRE PAIRING PROCEDURE

Necto Group App features (*depending on the device only some functions may be available)Dimmer management at 1 or 4 channels with different modes of operation:- Mono channel- 4 synchronized channels- RGB (3 channels or 3 zones)- RGB + White (4 channels or 4 zones)- Dynamic White

BLUETOOTH MODE + PUSH



In order to install the app on your Apple or Android device you need to scan the desiredQRCode to be automatically redirected to the IoT Light application.

As an alternative you can download the app by clicking on one of two links below:

Apple:https://goo.gl/QezZ5S

Android:https://goo.gl/5RKYmm



PARAMETERS CONFIGURATION

CLICK ON THE WANTED CONFIGURATION TO VIEW 2AMIN4030000N PROGRAMMER IMAGE

ResetConfiguration A B C D 1 2 3 4 5 6 7 8 9 10

Reset ON ON ON ON ON ON ON ON ON ON ON ON ON ON

Dimming CurveConfiguration A B C D 1 2 3 4 5 6 7 8 9 10

Logarithmic OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFLinear OFF OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF ON

PWMConfiguration A B C D 1 2 3 4 5 6 7 8 9 10PWM Standard OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFPWM Inverted OFF OFF ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF ON

FadeConfiguration A B C D 1 2 3 4 5 6 7 8 9 10

Fade Off OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF OFFFade On OFF OFF ON ON OFF OFF OFF OFF OFF OFF OFF OFF OFF ON


Documents

USER MANUAL 2AMDI511VPVRDBS - nectogroup.com · The maximum current absorbed by 0-10V dimmer ... a signal in direct or alternating ... In order to install the app on your Apple or