Embed Size (px)
Citation preview
SAFE® Select Technology, Optional Flight Envelope Protection
Valiant™ 1.3m
Instruction Manual BedienungsanleitungManuel d’utilisation Manuale di Istruzioni
EN
Valiant™ 1.3m
As the user of this product, you are solely responsible for operating in a manner that does not endanger yourself and others or result in damage to the product or the property of others.
• Always keep a safe distance in all directions around your model to avoid collisions or injury. This model is controlled by a radio signal subject to interference from many sources outside your control. Interference can cause momentary loss of control.
• Always operate your model in open spaces away from full-size vehicles, traffic and people.
• Always carefully follow the directions and warnings for this and any optional support equipment (chargers, rechargeable battery packs, etc.).
• Always keep all chemicals, small parts and anything electrical out of the reach of children.
• Always avoid water exposure to all equipment not specifically designed and protected for this purpose. Moisture causes damage to electronics.
• Never place any portion of the model in your mouth as it could cause serious injury or even death.
• Never operate your model with low transmitter batteries.
• Always keep aircraft in sight and under control.
• Always use fully charged batteries.
• Always keep transmitter powered on while aircraft is powered.
• Always remove batteries before disassembly.
• Always keep moving parts clean.
• Always keep parts dry.
• Always let parts cool after use before touching.
• Always remove batteries after use.
• Always ensure failsafe is properly set before flying.
• Never operate aircraft with damaged wiring.
• Never touch moving parts.
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit www.horizonhobby.com and click on the support tab for this product.
Meaning of Special Language:
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Safety Precautions and Warnings
14+ AGE RECOMMENdATION: Not for children under 14 years. This is not a toy.
WARNING AGAINST COUNTERFEIT PROdUCTS: If you ever need to replace your Spektrum receiver found in a Horizon Hobby product, always purchase from Horizon Hobby, LLC or a Horizon Hobby
authorized dealer to ensure authentic high-quality Spektrum product. Horizon Hobby, LLC disclaims all support and warranty with regards, but not limited to, compatibility and performance of counterfeit products or products claiming compatibility with DSM or Spektrum technology.
2
EN
To register your product online, visit www.e-fliterc.com
Box ContentsQuick Start Information
Transmitter Setup
Set up your transmitter using the transmitter setup chart
dual Rates
Hi Rate Low Rate
Ail p28mm q18mm p17mm q14mm
Ele 25mm 20mm
Rud 38mm 25mm
Flaps Landing q=30mm
Takeoff q=15mm
Center of Gravity (CG)
65mm +/-3mm back from leading edge of wing at the fuselage.
Flight Timer Setting 5 minutes
Table of Contents
40 OZ (1135 g)
38 in
(960
mm
)
(53 in 1350mm)
Specifications
Motor: 480 BL Outrunner Motor; 960Kv (PKZ4416)
Installed Installed
ESC: 30-Amp Pro Switch-Mode BEC Brushless ESC (V2)(EFLA1030B)
Installed Installed
SV80 servo (PKZ1080, PKZ1081) Installed Installed
Receiver: Spektrum™ AR636A 6-Channel Sport Receiver (SPMAR636A)
InstalledRequired
toComplete
Recommended Battery: 2200mAh 11.1V 3S 30C Li-Po ((EFLB22003S30))
Required to
Complete
Required to
Complete Recommended Battery Charger: 3-cell Li-Po battery balancing charger
Required to
Complete
Required to
CompleteRecommended Transmitter: Full-Range 6 channel (or more) 2.4GHz with Spektrum
DSM2®/DSMX® technology with adjustable Dual Rates
Required to
Complete
Required to
Complete
430 Sq In (27.75 Sq Dm)
3
As of this printing, you are required to register with the FAA if you own this product.
For up-to-date information on how to register with the FAA, visit https://registermyuas.faa.gov/.
For additional assistance on regulations and guidance on UAS usage, visit knowbeforeyoufly.org/.
SAFE® Select Technology ...................................................................4Preflight .............................................................................................4Transmitter Setup .............................................................................4Model Assembly ................................................................................5Model Assembly Continued ................................................................6Control Horn and Servo Arm Settings .................................................8Battery Installation and ESC Arming ...................................................9Binding ...........................................................................................10SAFE® Select Switch Designation ....................................................11AS3X Control Direction Test .............................................................11In Flight Trimming ............................................................................12Flying Tips and Repairs ....................................................................12Center of Gravity (CG) .....................................................................13PNP Receiver Selection and Installation ...........................................13Motor Service ..................................................................................13Post Flight .......................................................................................14Troubleshooting Guide AS3X ............................................................14Troubleshooting Guide .....................................................................15AMA National Model Aircraft Safety Code .........................................16Limited Warranty .............................................................................17Contact Information .........................................................................18FCC Information ...............................................................................18IC Information ..................................................................................18Compliance Information for the European Union ...............................18Replacement Parts ...........................................................................67Optional Parts ..................................................................................67
EN
Valiant™ 1.3m
Preflight
Transmitter Setup IMPORTANT: After you set up your model, always rebind the transmitter and receiver to set the desired failsafe positions.
dual RatesTake first flights in Low Rate. For landings, use high rate elevator.
NOTICE: To ensure AS3X® technology functions properly, do not lower rate values below 50%. If lower rates are desired, manually adjust the position of the pushrods on the servo arm.
NOTICE: If oscillation occurs at high speed, refer to the Troubleshooting Guide for more information.
Expo
After first flights, you may adjust expo in your transmitter or refer to the AR636 receiver manual for expo adjustment.
SAFE® Select TechnologyThe evolutionary SAFE® Select technology can offer an extra level of protection so you can perform the first flight with confidence. No complex transmitter programming is required. Just follow the simple bind process to make the SAFE Select system active. When activated, bank and pitch limitations keep you from over-controlling and automatic self-leveling makes recovery from risky or confusing attitudes as simple as releasing the sticks. In fact, with the aileron, elevator and rudder sticks in the neutral position, SAFE Select will automatically keep the airplane in a straight and level attitude.
Expand the advantage of what SAFE® Select technology offers by assigning it to a switch. No transmitter programming is required and you’ll be able to turn the system ON and OFF with the flip of a switch. For example, turn SAFE select ON for takeoffs to counter the torque of a large 5 blade propeller. Turn it OFF in flight for unrestricted aerobatic performance, and turn it back ON when a buddy wants to try out your cool warbird. Turn SAFE Select ON for landings. As you drop the landing gear, SAFE Select reduces your workload by compensating for pitch changes automatically, regardless of throttle position. It will help keep the correct pitch attitude and wings level during the final approach. Whether you’re a beginner or an expert, SAFE Select can make your flights a great experience.
When the normal bind process is followed, the SAFE Select system is disabled, leaving specially tuned AS3X® technology in place to deliver a pure, unrestricted flight experience.
1. Remove and inspect contents.
2. Read this instruction manual thoroughly.
3. Charge the flight battery.
4. Setup Transmitter using transmitter setup chart.
5. Fully assemble the airplane.
6. Install the flight battery in the aircraft (once it has been fully charged).
7. Check the Center of Gravity (CG).
8. Bind the aircraft to your transmitter.
9. Make sure linkages move freely.
10. Test the flap operation.
11. Perform the Control Direction Test with the transmitter.
12. Perform the AS3X Control Direction Test with the aircraft.
13. Adjust flight controls and transmitter.
14. Perform a radio system Range Test.
15. Find a safe open area to fly.
16. Plan flight for flying field conditions.
4
Computerized Transmitter Setup (dX6i, dX6, dX6e, dX7, dX7S, dX8, dX9, dX10t and dX18)
Start all transmitter programming with a blank ACRO model (do a model reset), then name the model.
Set Dual Rates to:HIGH 100% LOW 70%
Set Servo Travel to: 100%
DX6i
1. Go to the SETUP LIST MENU2. Set MODEL TYPE: ACRO3. Go to ADJUST LIST MENU4. Set FLAPS: Norm –100 Flap LAND £100
Flap
DX7SDX8
1. Go to the SYSTEM SETUP2. Set MODEL TYPE: AIRPLANE 3. Set WING TYPE: 1 AIL 1 FLAP4. Go to the FUNCTION LIST5. Set FLAP SYSTEM: Choose Flap NORM: -100% FLAP MID: 0% FLAP 3% ELEVATOR LAND: 100% FLAP 5% ELEVATOR SPEED 2.0S: SWITCH = FLAP
DX6DX6eDX7 DX9DX10tDX18
1. Go to the SYSTEM SETUP2. Set MODEL TYPE: AIRPLANE 3. Set AICRAFT TYPE: WING: 1 AIL 1 FLAP4. Go to the FUNCTION LIST5. Set FLAP SYSTEM: SELECT SWITCH D: POS 0: -100% FLAP POS 1: 0% FLAP 3% ELEVATOR POS 2: 100% FLAP 5% ELEVATOR SPEED 2.0
EN
Model Assembly
Main Landing Gear Installation 1. Remove the battery compartment door (A) from the bottom of the fuselage.
1. Slide the pre assembled landing gear (B) into the fuselage as shown.
1. Secure with the 4 screws (C).
2. Re-install the battery hatch.
A
B
C
Tail Installation 1. Install the Vertical stab (A) over the Horizontal stab (B) by sliding the 2
plastic tabs down through the holes in the horizontal stab, creating a complete tail assembly.
TIP: You may wish to secure the vertical and horizontal stabs with a thin piece of double sided tape.
1. Place the tail assembly (C) onto the fuselage by first inserting the front of the vertical stab into the fuselage.
2. Lower the back of the assembly down onto the fuselage, lining up the 2 plastic tabs with the 2 holes in the fuselage.
1. Secure the tail with 2 screws (d) inserted from the bottom of the fuselage and 1 screw (E) into the tail wheel bracket as shown.
IMPORTANT: DO NOT over tighten the screws.
2. Attach the clevis to both the elevator and rudder control horns (see instructions for clevis connection).
Tail Wheel Installation1. Slide the tail wheel assembly (A) into the slot in the bottom of the rudder as
shown.
2. Rotate the assembly until it locks into the clamps moulded into the tail wheel bracket.
A
dE
B
C
A
5
EN
Valiant™ 1.3m
Model Assembly Continued
Wing Installation 1. Slide the 1 large (A) and 1 small (B), carbon fiber wing tubes into one wing
half and then join the 2 halves together.
2. Connect the Flaps and Aileron connectors to respective Y-harnesses connected to the receiver. The left and right servos can be connected to either side of a Y-harness.
IMPORTANT: The ailerons must be connected to the receiver’s AILE (#2 channel) with a Y-harness (included) for the AS3X system to function properly.
3. Carefully lay the wing assembly on top of the fuselage and secure with the large wing connecter and 4 screws as shown.
CAUTION: DO NOT crush or otherwise damage the wiring when attaching the wing to the fuselage.
A
B
Ailerons
Flaps
A
6
EN
Float Installation (Optional)
Float Assembly
1. Install the 2 cross members (A) and the front and rear struts (B) on one float as shown and secure with 4 included screws (C).
2. Install the other float onto the assembled struts as in Step 1 above.
IMPORTANT: The front strut is taller than the rear strut. (Figure 1)
Float Assembly Installation
1. With the landing gear and battery hatch removed, align and mount the float assembly to the bottom of the fuselage.
2. Secure the back section of the floats to the fuselage using the 2 included brackets (A) and 4 screws (B).
3. Secure the front section of the floats using the two larger brackets (C) and 4 screws (d).
4. Re-install the battery hatch.
Disassemble in reverse order.
Fig. 1
d
BC
B
AC
A
7
EN
Valiant™ 1.3m
Control Horn and Servo Arm SettingsThe table to the right shows the factory settings for the control horns and servo arms. Fly the aircraft at factory settings before making changes.
NOTICE: If control throws are changed from the factory settings, the AR636 gain values may need to be adjusted. Refer to the Spektrum AR636 manual for adjustment of gain values.
After flying, you may choose to adjust the linkage positions for the desired control response. See the table to the right.
Horns Arms
ElevatorElevator
Flaps
Ailerons
Ailerons
Elevator
Flaps
Ailerons
Elevator
Flaps
Ailerons
Flaps
Elevator
Flaps
Ailerons
RudderElevator
Flaps
Ailerons
More control throw Less control throw
Elevator
Flaps
Ailerons
Elevator
Flaps
Ailerons
Elevator
Flaps
Ailerons
1.
2.
3.
4.
5.
6.
Clevis Installation• Pull the tube from the clevis to the linkage.
• Carefully spread the clevis, then insert the clevis pin into the desired hole in the control horn.
• Move the tube to hold the clevis on the control horn.
Control Surface CenteringAfter assembly and transmitter setup, confirm that the control surfaces are centered. If the control surfaces are not centered, mechanically center the control surfaces by adjusting the linkages.
If adjustment is required, turn the clevis on the linkage to change the length of the linkage between the servo arm and the control horn.
After binding a transmitter to the aircraft receiver, set the trims and sub-trims to 0, then adjust the clevises to center the control surfaces.
8
EN
Battery SelectionWe recommend the E-flite® 2200mAh 11.1V 3S 30C Li-Po battery (EFLB22003S30). Refer to the Optional Parts List for other recommended batteries. If using a battery other than those listed, the battery should be within the range of capacity, dimensions and weight of the E-flite Li-Po battery packs to fit in the fuselage. Be sure the model balances at the recommended CG.
1. Lower the throttle and throttle trim to the lowest settings. Power on the Transmitter, then wait 5 seconds.
2. Unlock and lift the back of the battery hatch (A) to remove.
3. For added security, apply the loop side (soft side) of the optional hook and loop tape (B) to the bottom of your battery and the hook side to the battery tray.
4. Install the fully charged battery (C) all the way forward in the battery compartment as shown. Secure using the hook and loop strap (d).
5. Connect the battery to the ESC (the ESC is now armed).
6. place the aircraft on its wheels with wings level
7. Keep the aircraft immobile and away from wind or the system will not initialize.
• The ESC will sound a series of tones (refer to step 7 of the binding instructions for more information).
• An LED will light on the receiver.
8. If the ESC sounds a continuous double beep after the flight battery is connected, recharge or replace the battery.
9. Reinstall the battery hatch.
Battery Installation and ESC Arming
CAUTION: Always keep hands away
from the propeller. When armed, the motor will turn the propeller in response to any throttle movement.
B
Optional
d
A
C
9
EN
Valiant™ 1.3m
Switching OFF SAFE Select Binding Sequence
Install Bind Plug
RX in Bind ModeBind TX to RX
Remove Bind Plug
Install Bind Plug Remove Bind Plug
RX in Bind ModeBind TX to RX
This product requires an approved Spektrum™ DSM2®/DSMX® compatible transmitter. Visit www.bindnfly.com for a complete list of approved transmitters.
The aircraft has an optional SAFE Select feature, which can be switched ON or OFF easily by binding in a specific manner as described below.
IMPORTANT: Before binding a transmitter, read the Transmitter Setup section of this manual to ensure that your transmitter is properly programmed for this aircraft.
Transmitter and Receiver Binding / Switching ON and OFF SAFE Select
Bind Plug Installation
BINd PLUG
Binding Procedure / Switching OFF SAFE SelectIMPORTANT: The included AR636 receiver has been programmed for operation specifically for this aircraft. Refer to the receiver manual for correct setup if the receiver is replaced or is used in another aircraft.
CAUTION: When using a Futaba® transmitter with a Spektrum DSM module, you must reverse the throttle channel and rebind. Refer to
your Spektrum module manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.
1. Make sure the transmitter is powered off.
2. Move the transmitter controls to neutral (flight controls: rudder, elevators and ailerons) or to low positions (throttle, throttle trim). *
3. Install a bind plug in the receiver bind port.
4. Place the aircraft level on its wheels, connect the flight battery to the ESC, then turn ON the switch. The ESC will produce a series of sounds. One long tone, then 3 short tones confirm that the LVC is set correctly for the ESC.
The orange bind LEd on the receiver will begin to flash rapidly. dO NOT remove the bind plug at this time.
5. Take 3 steps away from the aircraft /receiver and then power ON the transmitter while holding the transmitter bind button or switch. Refer to your transmitter’s manual for specific binding instructions. IMPORTANT: Do not to point the transmitter’s antenna directly at the receiver while binding. IMPORTANT: Keep away from large metal objects while binding.
6. The receiver is bound to the transmitter when the orange bind light on the receiver stays orange. The ESC will also produce a series of three ascending tones. The tones indicate the ESC is armed, provided the throttle stick and throttle trim are low enough to trigger arming.
7. Remove the bind plug from the bind port. IMPORTANT: Once bound, the receiver will retain its bind and last setting until it has been intentionally changed, even when power is cycled ON and OFF. However, if you notice that bind has been lost, simply repeat the binding processs.
SAFE Select OFF Indication
Every time the receiver is powered ON the surfaces will cycle back and forth once to indicate that SAFE Select has been switched OFF.
The throttle will not arm if the transmitter’s throttle control is not put at the lowest position. If you encounter problems, follow the binding instructions and refer to the transmitter troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Product Support office.
Binding Procedure / Switching ON SAFE SelectIMPORTANT: The included AR636 receiver has been programmed for operation specifically for this aircraft. Refer to the receiver manual for correct setup if the receiver is replaced or is used in another aircraft.
CAUTION: When using a Futaba® transmitter with a Spektrum DSM module, you must reverse the throttle channel and rebind. Refer to
your Spektrum module manual for binding and failsafe instructions. Refer to your Futaba transmitter manual for instructions on reversing the throttle channel.
1. Make sure the transmitter is powered off.
2. Move the transmitter controls to neutral (flight controls: rudder, elevators and ailerons) or to low positions (throttle, throttle trim).*
3. Install a bind plug in the receiver bind port.
4. Place the aircraft level on its wheels, connect the flight battery to the ESC, then turn ON the switch. The ESC will produce a series of sounds. One long tone, then 3 short tones confirm that the LVC is set correctly for the ESC. The orange bind LED on the receiver will begin to flash rapidly.
5. Remove the bind plug from the bind port.
6. Take 3 steps away from the aircraft /receiver and then power ON the transmitter while holding the transmitter bind button or switch. Refer to your transmitter’s manual for specific binding instructions. IMPORTANT: Do not to point the transmitter’s antenna directly at the receiver while binding. IMPORTANT: Keep away from large metal objects while binding.
7. The receiver is bound to the transmitter when the orange bind light on the receiver stays orange. The ESC will also produce a series of three ascending tones. The tones indicate the ESC is armed, provided the throttle stick and throttle trim are low enough to trigger arming.
IMPORTANT: Once bound, the receiver will retain its bind and last setting until it has been intentionally changed, even when power is cycled ON and OFF. However, if you notice that bind has been lost, simply repeat the binding processs.
SAFE Select ON Indication
Every time the receiver is powered ON the surfaces will cycle back and forth twice with a slight pause at neutral position to indicate that SAFE Select is switched ON.
The throttle will not arm if the transmitter’s throttle control is not put at the lowest position. If you encounter problems, follow the binding instructions and refer to the transmitter troubleshooting guide for other instructions. If needed, contact the appropriate Horizon Product Support office.
*FailsafeIf the receiver loses transmitter communication, the failsafe will activate. When activated, failsafe moves the throttle channel to its preset failsafe position (low throttle) that was set during binding. All other channels move to actively level the aircraft in flight.
Switching ON SAFE Select Binding Sequence
10
EN
SAFE® Select Switch designation SAFE® Select technology can be easily assigned to any open switch on your transmitter. With this new feature, you now have the flexibility to enable or dis-able the technology while in flight.
IMPORTANT: Before assigning your desired switch, ensure that the travel for that channel is set at 100%.
Assigning a switch
1. Bind the aircraft correctly to activate SAFE Select. This will allow the system to be assigned to a switch.
2. Hold both transmitter sticks to the inside bottom corners and toggle the desired switch 5 times to assign that switch. The control surfaces of the aircraft will move, indicating the switch has been selected.
Repeat the process to assign a different switch if desired.
NOTICE: SAFE Select is assignable on Channels 5–9.
Mode 1 and 2 Transmitters
x 5
AS3X Control direction Test This test ensures that the AS3X® control system is functioning properly. Assemble the aircraft and bind your transmitter to the receiver before performing this test.
1. Raise the throttle just above 25%, then lower the throttle to activate AS3X technology.
CAUTION: Keep all body parts, hair and loose clothing away from a moving propeller, as these items could become entangled.
IMPORTANT: The AR636 programming for this aircraft increases control surface movement when landing gear is down.
2. Move the entire aircraft as shown and ensure the control surfaces move in the direction indicated in the graphic. If the control surfaces do not respond as shown, do not fly the aircraft. Refer to the receiver manual for more information.
Once the AS3X system is active, control surfaces may move rapidly. This is normal. AS3X remains active until the battery is disconnected.
Aircraft movement AS3X Reaction
Ele
va
tor
Ail
ero
nR
ud
de
r
11
EN
Valiant™ 1.3m
Flying Tips and RepairsConsult local laws and ordinances before choosing a flying location.
Range Check your Radio SystemBefore you fly, range check the radio system. Refer to your specific transmitter instruction manual for range test information.
OscillationOnce the AS3X system is active (after advancing the throttle for the first time),
you will normally see the control surfaces react to aircraft movement. In some flight conditions you may see oscillation (the aircraft rocks back and forth on one axis due to overcontrol). If oscillation occurs, refer to the Troubleshooting Guide for more information.
TakeoffPlace the aircraft facing into the wind. Set your transmitter in low rate and use your flaps switch to drop the flaps to takeoff or “half position”. Gradually increase the throttle to ¾ and steer with the rudder. Flaps make takeoffs shorter. As the tail comes off the ground, pull back gently on the elevator. Climb to a comfortable altitude and then use your flaps switch to raise the flaps for normal flight.
FlyingFor your first flights with the recommended battery pack (EFLB22003S30), set your transmitter timer or a stopwatch to 5 minutes. After five minutes, land the aircraft. Adjust your timer for longer or shorter flights once you have flown the model. If at any time the motor pulses, land the aircraft immediately to recharge the flight battery. See the Low Voltage Cutoff (LVC) section for more details on maximizing battery health and run time.
Landing
Land the aircraft into the wind. Use high rate Elevator for landings. Use a small amount of throttle for the entire descent. Lower the throttle to ¼ and use your flaps switch to deploy the flaps to the landing or “full down position”. Flaps will make the landing approach steeper and slower, and allow for a smoother landing.
Keep the throttle on until the aircraft is ready to flare. During flare, keep the wings level and the aircraft pointed into the wind. Gently lower the throttle while pulling back on the elevator to bring the aircraft down on its wheels.
If landing on grass, it is best to hold full up elevator after touchdown and when taxiing to prevent nosing over.
Once on the ground, avoid sharp turns until the plane has slowed enough to prevent scraping the wingtips.
NOTICE: If a crash is imminent, reduce the throttle and trim fully. Failure to do so could result in extra damage to the airframe, as well as damage to the ESC and motor.
NOTICE: After any impact, always ensure the receiver is secure in the fuselage. If you replace the receiver, install the new receiver in the same orientation as the original receiver or damage may result.
NOTICE: Crash damage is not covered under warranty.
NOTICE: When you are finished flying, never leave the aircraft in direct sunlight or in a hot, enclosed area such as a car. Doing so can damage the aircraft.
Low Voltage Cutoff (LVC)When a Li-Po battery is discharged below 3V per cell, it will not hold a charge. The ESC protects the flight battery from over-discharge using Low Voltage Cutoff (LVC). Before the battery charge decreases too much, LVC removes power supplied to the motor. Power to the motor pulses, showing that some battery power is reserved for flight control and safe landing.
Disconnect and remove the Li-Po battery from the aircraft after use to prevent trickle discharge. Charge your Li-Po battery to about half capacity before storage. During storage, make sure the battery charge does not fall below 3V per cell. LVC does not prevent the battery from over-discharge during storage.
NOTICE: Repeated flying to LVC will damage the battery.
Tip: Monitor your aircraft battery’s voltage before and after flying by using a Li-Po Cell Voltage Checker (EFLA111, sold separately).
RepairsThanks to the Z-Foam™ material in this aircraft, repairs to the foam can be made using virtually any adhesive (hot glue, regular CA, epoxy, etc). When parts are not repairable, see the Replacement Parts List for ordering by item number. For a listing of all replacement and optional parts, refer to the list at the end of this manual.
NOTICE: Use of CA accelerant on your aircraft can damage paint. DO NOT handle the aircraft until accelerant fully dries.
WARNING: Always decrease throttle at propeller strike.
During your first flight, trim the aircraft for level flight at 3/4 throttle with flaps up. Make small trim adjustments with your transmitter’s trim switches to straighten the aircraft’s flight path.
After adjusting trim, do not touch the control sticks for 3 seconds. This allows the receiver to learn the correct settings to optimize AS3X performance.
Failure to do so could affect flight performance.
In Flight Trimming
3 Seconds
12
EN
Center of Gravity (CG) The CG location is measured from the leading edge of the wing at the root. This CG location has been determined with the recommended Li-Po battery (EFLB22003S30) installed all the way forward in the battery compartment.
back from leading edge of wing at the fuselage.
65mm +/- 3mm
PNP Receiver Selection and Installation
The Spektrum AR636 receiver is recommended for ths airplane. If you choose to install another receiver, ensure that it is at least a 6-channel full range (sport) receiver. Refer to your receiver manual for correct installation and operation instructions.
Installation (AR636 shown)
1. Mount the receiver parallel to the length of the fuselage as shown. Use double-sided servo tape.
CAUTION: Incorrect installation of the receiver could cause a crash.
2. Attach the appropriate control surfaces to the their respective ports on the receiver using the chart in the illustration.
1 = Throttle2 = Aileron3 = Elevator4 = Rudder6 = Flaps
CAUTION: Always disconnect the flight battery before performingmotor service.
disassembly 1. Remove the spinner screw (A) and spinner (B) from the propeller shaft (G). 2. Remove the spinner nut (C) by using an adjustable wrench. 3. Remove the propeller (d), back spinner hub (E), prop hub (F) and the
propeller shaft from the motor shaft.4. Remove 4 screws from around the front cowling (H) and remove the
cowling from the fuselage.5. Remove the 4 screws and the motor (I) with the mount (J) from the
fuselage. 6. Disconnect the motor wires from the ESC wires.7. Remove the 4 screws and motor from the mount.
Assembly• Assemble in reverse order. • Correctly align and connect the motor wire colors with the ESC wires.• Install the propeller with the size numbers (10.75 X 8) facing out from the
motor. • Tighten the spinner nut to secure the propeller into place.
Motor Service
A
G
F
B
H
E
d
C
Wiring not shown
J
I
13
EN
Valiant™ 1.3m
Troubleshooting Guide AS3X
Problem Possible Cause Solution
Oscillation
Damaged propeller or spinner Replace propeller or spinner
Imbalanced propeller Balance the propeller. For more information, view John Redman’s propeller balancing video at www.horizonhobby.com
Motor vibration Replace parts or correctly align all parts and tighten fasteners as needed
Loose receiver Align and secure receiver in fuselage
Loose aircraft controls Tighten or otherwise secure parts (servo, arm, linkage, horn and control surface)
Worn parts Replace worn parts (especially propeller, spinner or servo)
Irregular servo movement Replace servo
Inconsistent flight performance
Trim is not at neutral If you adjust trim more than 8 clicks, adjust the clevis to remove trim
Sub-Trim is not at neutral No Sub-Trim is allowed. Adjust the servo linkage
Aircraft was not kept immobile for 5 seconds after battery connection
With the throttle stick in lowest position. Disconnect battery, then reconnect battery and keep the aircraft still for 5 seconds
Incorrect response to the AS3X Control Direction Test
Incorrect direction settings in the receiver, which can cause a crash
DO NOT fly. Correct the direction settings (refer to the receiver manual), then fly
Post Flight
1. Disconnect the flight battery from the ESC (Required for Safety and battery life).
2. Power OFF the transmitter.
3. Remove the flight battery from the aircraft.
4. Recharge the flight battery.
5. Repair or replace all damaged parts.
6. Store the flight battery apart from the aircraft and monitor the battery charge.
7. Make note of the flight conditions and flight plan results, planning for future flights.
14
EN
Problem Possible Cause Solution
Aircraft will not re-spond to throttle but responds to other controls
Throttle not at idle and/or throttle trim too high Reset controls with throttle stick and throttle trim at lowest setting
Throttle servo travel is lower than 100% Make sure throttle servo travel is 100% or greater
Throttle channel is reversed Reverse throttle channel on transmitter
Motor disconnected from ESC Make sure motor is connected to the ESC
Extra propeller noise or extra vibration
Damaged propeller and spinner, collet or motor Replace damaged parts
Propeller is out of balance Balance or replace propeller
Prop nut is too loose Tighten the prop nut
Reduced flight time or aircraft under-powered
Flight battery charge is low Completely recharge flight battery
Propeller installed backwards Install propeller with numbers facing forward
Flight battery damaged Replace flight battery and follow flight battery instructions
Flight conditions may be too cold Make sure battery is warm before use
Battery capacity too low for flight conditions Replace battery or use a larger capacity battery
Aircraft will not Bind (during binding) to transmitter
Transmitter too near aircraft during binding process Move powered transmitter a few feet from aircraft, disconnect and reconnect flight battery to aircraft
Aircraft or transmitter is too close to large metal ob-ject, wireless source or another transmitter Move aircraft and transmitter to another location and attempt binding again
The bind plug is not installed correctly in the bind port Install bind plug in bind port and bind the aircraft to the transmitter
Flight battery/transmitter battery charge is too low Replace/recharge batteries
Bind switch or button not held long enough during bind process
Power off transmitter and repeat bind process. Hold transmitter bind button or switch until receiver is bound
Aircraft will not connect (after binding) to transmitter
Transmitter too near aircraft during connecting pro-cess
Move powered transmitter a few feet from aircraft, disconnect and reconnect flight battery to aircraft
Aircraft or transmitter is too close to large metal ob-ject, wireless source or another transmitter Move aircraft and transmitter to another location and attempt connecting again
Bind plug left installed in bind port Rebind transmitter to the aircraft and remove the bind plug before cycling power
Aircraft bound to different model memory(ModelMatchTM radios only) Select correct model memory on transmitter
Flight battery/Transmitter battery charge is too low Replace/recharge batteries
Transmitter may have been bound to a different air-craft using different DSM protocol Bind aircraft to transmitter
Control surface does not move
Control surface, control horn, linkage or servo damage Replace or repair damaged parts and adjust controls
Wire damaged or connections loose Do a check of wires and connections, connect or replace as needed
Transmitter is not bound correctly or the incorrect airplanes was selected Re-bind or select correct airplanes in transmitter
Flight battery charge is low Fully recharge flight battery
BEC (Battery Elimination Circuit) of the ESC is dam-aged Replace ESC
Controls reversed Transmitter settings are reversed Perform the Control Direction Test and adjust the controls on transmitterappropriately
Motor power pulses then motor loses power
ESC uses default soft Low Voltage Cutoff (LVC) Recharge flight battery or replace battery that is no longer performing
Weather conditions might be too cold Postpone flight until weather is warmer
Battery is old, worn out, or damaged Replace battery
Battery C rating might be too small Use recommended battery
Troubleshooting Guide
15
EN
Valiant™ 1.3m
AMA National Model Aircraft Safety Code
16
Effective January 1, 2014
A. GENERAL
A model aircraft is a non-human-carrying aircraft capable of sustained flight in the atmosphere. It may not exceed limitations of this code and is intended exclusively for sport, recreation, education and/or competition. All model flights must be conducted in accordance with this safety code and any additional rules specific to the flying site.
1. Model aircraft will not be flown: (a) In a careless or reckless manner. (b) At a location where model aircraft activities are prohibited.
2. Model aircraft pilots will: (a) Yield the right of way to all man carrying aircraft. (b) See and avoid all aircraft and a spotter must be used when appropriate. (AMA Document #540-D.) (c) Not fly higher than approximately 400 feet above ground level within three (3) miles of an airport, without notifying the airport operator. (d) Not interfere with operations and traffic patterns at any airport, heliport or seaplane base except where there is a mixed use agreement. (e) Not exceed a takeoff weight, including fuel, of 55 pounds unless in compliance with the AMA Large Model Aircraft program. (AMA Document 520-A.) (f) Ensure the aircraft is identified with the name and address or AMA number of the owner on the inside or affixed to the outside of the model aircraft. (This does not apply to model aircraft flown indoors). (g) Not operate aircraft with metal-blade propellers or with gaseous boosts except for helicopters operated under the provisions of AMA Document #555. (h) Not operate model aircraft while under the influence of alcohol or while using any drug which could adversely affect the pilot’s ability to safely control the model. (i) Not operate model aircraft carrying pyrotechnic devices which explode or burn, or any device which propels a projectile or drops any object that creates a hazard to persons or property.
Exceptions:
•FreeFlightfusesordevicesthatburnproducingsmokeandare securely attached to the model aircraft during flight.
•Rocketmotors(usingsolidpropellant)uptoaG-seriessizemay be used provided they remain attached to the model during flight. Model rockets may be flown in accordance with the National Model Rocketry Safety Code but may not be launched from model aircraft.
•OfficiallydesignatedAMAAirShowTeams(AST)areauthorizedto use devices and practices as defined within the Team AMA Program Document (AMA Document #718). (j) Not operate a turbine- powered aircraft, unless in compliance with the AMA turbine regulations. (AMA Document #510-A).
3. Model aircraft will not be flown in AMA sanctioned events, air shows or model demonstrations unless:
(a) The aircraft, control system and pilot skills have successfully demonstrated all maneuvers intended or anticipated prior to the specific event.
(b) An inexperienced pilot is assisted by an experienced pilot.
4. When and where required by rule, helmets must be properly worn and fastened. They must be OSHA, DOT, ANSI, SNELL or NOCSAE approved or comply with comparable standards.
B. RAdIO CONTROL
1. All pilots shall avoid flying directly over unprotected people, vessels, vehicles or structures and shall avoid endangerment of life and property of others.
2. A successful radio equipment ground-range check in accordance with manufacturer’s recommendations will be completed before the first flight of a new or repaired model aircraft.
3. At all flying sites a safety line(s) must be established in front of which all flying takes place (AMA Document #706.)
(a) Only personnel associated with flying the model aircraft are allowed at or in front of the safety line.
(b) At air shows or demonstrations, a straight safety line must be established.
(c) An area away from the safety line must be maintained for spectators.
(d) Intentional flying behind the safety line is prohibited.
4. RC model aircraft must use the radio-control frequencies currently allowed by the Federal Communications Commission (FCC). Only individuals properly licensed by the FCC are authorized to operate equipment on Amateur Band frequencies.
5. RC model aircraft will not operate within three (3) miles of any pre-existing flying site without a frequency-management agreement (AMA Documents #922 and #923.)
6. With the exception of events flown under official AMA Competition Regulations, excluding takeoff and landing, no powered model may be flown outdoors closer than 25 feet to any individual, except for the pilot and the pilot’s helper(s) located at the flight line.
7. Under no circumstances may a pilot or other person touch a model aircraft in flight while it is still under power, except to divert it from striking an individual.
8. RC night flying requires a lighting system providing the pilot with a clear view of the model’s attitude and orientation at all times. Hand-held illumi- nation systems are inadequate for night flying operations.
9. The pilot of a RC model aircraft shall:
(a) Maintain control during the entire flight, maintaining visual contact without enhancement other than by corrective lenses prescribed for the pilot.
(b) Fly using the assistance of a camera or First-Person View (FPV) only in accordance with the procedures outlined in AMA Document #550.
(C) Fly using the assistance of autopilot or stabilization system only in accordance with the procedures outlined in AMA Document #560.
Please see your local or regional modeling association’s guidelines for proper, safe operation of your model aircraft.
EN
Limited Warranty
17
What this Warranty Covers Horizon Hobby, LLC, (Horizon) warrants to the original purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the date of purchase.
What is Not Covered This warranty is not transferable and does not cover (i) cosmetic damage, (ii) damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or due to improper use, installation, operation or maintenance, (iii) modification of or to any part of the Product, (iv) attempted service by anyone other than a Horizon Hobby authorized service center, (v) Product not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical regulations, or (vii) use that violates any applicable laws, rules, or regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO OTHER WARRANTY OR REPRESENTATION, AND HEREBY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES OF NON-INFRINGEMENT, MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE PURCHASER ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE REQUIREMENTS OF THE PURCHASER’S INTENDED USE.
Purchaser’s Remedy Horizon’s sole obligation and purchaser’s sole and exclusive remedy shall be that Horizon will, at its option, either (i) service, or (ii) replace, any Product determined by Horizon to be defective. Horizon reserves the right to inspect any and all Product(s) involved in a warranty claim. Service or replacement decisions are at the sole discretion of Horizon. Proof of purchase is required for all warranty claims. SERVICE OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE PURCHASER’S SOLE AND EXCLUSIVE REMEDY.
Limitation of Liability HORIZON SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF WHETHER SUCH CLAIM IS BASED IN CONTRACT, WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Further, in no event shall the liability of Horizon exceed the individual price of the Product on which liability is asserted. As Horizon has no control over use, setup, final assembly, modification or misuse, no liability shall be assumed nor accepted for any resulting damage or injury. By the act of use, setup or assembly, the user accepts all resulting liability. If you as the purchaser or user are not prepared to accept the liability associated with the use of the Product, purchaser is advised to return the Product immediately in new and unused condition to the place of purchase.
Law These terms are governed by Illinois law (without regard to conflict of law principals). This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. Horizon reserves the right to change or modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services Your local hobby store and/or place of purchase cannot provide warranty support or service. Once assembly, setup or use of the Product has been started, you must contact your local distributor or Horizon directly. This will enable Horizon to better answer your questions and service you in the event that you may need any assistance. For questions or assistance, please visit our website at www.horizonhobby.com, submit a Product Support Inquiry, or call the toll free telephone number referenced in the Warranty and Service Contact Information section to speak with a Product Support representative.
Inspection or Services
If this Product needs to be inspected or serviced and is compliant in the country you live and use the Product in, please use the Horizon Online Service Request submission process found on our website or call Horizon to obtain a Return Merchandise Authorization (RMA) number. Pack the Product securely using a shipping carton. Please note that original boxes may be included, but are not designed to withstand the rigors of shipping without additional protection. Ship via a carrier that provides tracking and insurance for lost or damaged parcels, as Horizon is not responsible for merchandise until it arrives and is accepted at our facility. An Online Service Request is available at http://www.horizonhobby.com/content/_service-center_render-service-center. If you
do not have internet access, please contact Horizon Product Support to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, you will be asked to provide your complete name, street address, email address and phone number where you can be reached during business hours. When sending product into Horizon, please include your RMA number, a list of the included items, and a brief summary of the problem. A copy of your original sales receipt must be included for warranty consideration. Be sure your name, address, and RMA number are clearly written on the outside of the shipping carton.
NOTICE: do not ship LiPo batteries to Horizon. If you have any issue with a LiPo battery, please contact the appropriate Horizon Product Support office.
Warranty Requirements For Warranty consideration, you must include your original sales receipt verifying the proof-of-purchase date. Provided warranty conditions have been met, your Product will be serviced or replaced free of charge. Service or replacement decisions are at the sole discretion of Horizon.
Non-Warranty Service
Should your service not be covered by warranty, service will be completed and payment will be required without notification or estimate of the expense unless the expense exceeds 50% of the retail purchase cost. By submitting the item for service you are agreeing to payment of the service without notification. Service estimates are available upon request. You must include this request with your item submitted for service. Non-warranty service estimates will be billed a minimum of ½ hour of labor. In addition you will be billed for return freight. Horizon accepts money orders and cashier’s checks, as well as Visa, MasterCard, American Express, and Discover cards. By submitting any item to Horizon for service, you are agreeing to Horizon’s Terms and Conditions found on our website http://www.horizonhobby.com/content/_service-center_render-service-center.
ATTENTION: Horizon service is limited to Product compliant in the country of use and ownership. If received, a non-compliant Product will not be serviced. Further, the sender will be responsible for arranging return shipment of the un-serviced Product, through a carrier of the sender’s choice and at the sender’s expense. Horizon will hold non-compliant Product for a period of 60 days from notification, after which it will be discarded.
10/15
EN
Valiant™ 1.3m
Compliance Information for the European Union
Contact Information
EFL Valiant 1.3m BNF Basic (EFL4975) EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the R&TTE and EMC Directive.
EFL Valiant 1.3m PNP (EFL4950) EU Compliance Statement: Horizon Hobby, LLC hereby declares that this product is in compliance with the essential requirements and other relevant provisions of the EMC Directive.
A copy of the EU Declaration of Conformity is available online at: http://www.horizonhobby.com/content/support-render-compliance.
18
Country of Purchase Horizon Hobby Phone Number/Email Address Address
United States of America
Horizon Service Center(Repairs and Repair Requests)
servicecenter.horizonhobby.com/RequestForm/
4105 Fieldstone Rd Champaign, Illinois, 61822 USAHorizon Product Support
(Product Technical Assistance)[email protected]
877-504-0233
800-338-4639
United KingdomService/Parts/Sales:
Horizon Hobby Limited
[email protected] Units 1–4 , Ployters Rd, Staple Tye
Harlow, Essex, CM18 7NS, United Kingdom+44 (0) 1279 641 097
GermanyHorizon Technischer Service [email protected]
Christian-Junge-Straße 1 25337 Elmshorn, GermanySales: Horizon Hobby GmbH +49 (0) 4121 2655 100
France Service/Parts/Sales: Horizon Hobby SAS
[email protected] 11 Rue Georges Charpak
77127 Lieusaint, France+33 (0) 1 60 18 34 90
Instructions for disposal of WEEE by users in the European UnionThis product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their waste equipment by handing it over to a designated collections point for the recycling of waste electrical and electronic equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more information about where you can drop off your waste equipment for recycling, please contact your local city office, your household waste disposal service or where you purchased the product.
FCC Information
Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be compliant with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
IC Information
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
IC: 6157A-AMRX15
FCC Id: BRWdASRX15
67
Replacement Parts • Ersatzteile • Pièces de rechange • Pezzi di ricambio
Optional Parts • Optionale Bauteile • Pièces optionnelles • Pezzi opzionali
Part # | NummerNuméro | Codice Description Beschreibung Description Descrizione
EFL4951 Painted Valiant 1.3 fuse Painted Valiant 1.3 fuse Valiant 1.3 - Fuselage peint Fusoliera verniciata Valiant 1.3
EFL4952 Painted Valiant 1.3 wing Painted Valiant 1.3 wing Valiant 1.3 - Aile peinte Ala verniciata Valiant 1.3
EFL4953 Valiant 1.3 carbon wing tube Valiant 1.3 carbon wing tube Valiant 1.3 - Clé d'aile en carbone Tubetto ala in carbonio Valiant 1.3
EFL4954 Valiant 1.3 Spinner Valiant 1.3 Spinner Valiant 1.3 - Cône Ogiva Valiant 1.3
EFL4955 Valiant 1.3 Landing gear set Valiant 1.3 Landing gear set Valiant 1.3 - Train d'atterrissage Carrello d’atterraggio Valiant 1.3
EFL4956 Valiant 1.3 Hardware/screw set Valiant 1.3 Hardware/screw set Valiant 1.3 - Visserie Set viti e accessori Valiant 1.3
EFL4957 Valiant 1.3 Float Struts Valiant 1.3 Float Struts Valiant 1.3 - Haubans de flotteurs Gambe galleggianti Valiant 1.3
EFL4958 Valiant 1.3 pushrod set Valiant 1.3 pushrod set Valiant 1.3 - Tringlerie Set rinvii Valiant 1.3
EFL4959 Valiant 1.3 Motor mount/hardware Valiant 1.3 Motor mount/hardware Valiant 1.3 - Support moteur/visserie Supporto motore e accessori
EFL4960Valiant 1.3 Plastic part set (cowl,door,joiner)
Valiant 1.3 Plastic part set (cowl,door,joiner)
Valiant 1.3 - Pièces plastique (capot, porte, clé)
Set parti in plastica (naca,sportello, giunto)
EFL4961 Valiant 1.3 Vertical Fin/Rudder Valiant 1.3 Vertical Fin/Rudder Valiant 1.3 - Stabilsateur vertical / dérive Pinna verticale/direzionale Valiant 1.3
EFL4962 Valiant 1.3 Horizontal stab / elevator Valiant 1.3 Horizontal stab / elevator Valiant 1.3 - Stabilisateur horizontal / profondeur Stabilizzatore orizz./elevatore Valiant 1.3
EFLA1030B 30-Amp Pro Switch-Mode BEC Brushless ESC (V2)
30-Amp Pro Switch-Mode BEC Brushless ESC (V2)
Contrôleur Brushless 30A Pro Switch-Mode BEC (V2)
ESC brushless 30 A Pro Switch-Mode BEC (V2)
PKZ1080 SV80 Short Lead 3-Wire Servo: AB3 SV80 Short Lead 3-Wire Servo: AB3 Servo SV80 câble court 3-fils: AB3 Servo SV80 cavo corto 3 fili: AB3
PKZ1081 SV80 Long Lead 3-wire servo: T28 SV80 Long Lead 3-wire servo: T28 Servo SV80 câble long 3-fils: T28 Servo SV80 cavo lungo 3 fili: T28
PKZ4416 480 BL Outrunner Motor; 960Kv 480 BL Outrunner Motor; 960Kv Moteur BL 480 à cage tournante, 960Kv
Motore outrunner 480 brushless; 960 kV
PKZ6901 Propeller: 10.75 X 8 Propeller: 10.75 X 8 Hélice 10,75 x 8 Elica: 10,75 x 8
SPMAR636 AR636 6-Channel AS3X Sport Receiver AR636 6-Channel AS3X Sport Receiver Récepteur Spektrum AR636 6 voies
AS3X Ricevente sport AR636 AS3X 6 canali
Part # | NummerNuméro | Codice Description Beschreibung Description Descrizione
HBZ7390 Float set Set galleggianti
EFLA250 Park Flyer Tool Assortment, 5 pc Park Flyer Werkzeugsortiment, 5 teilig Assortiment d'outils park flyer, 5pc Park Flyer assortimento attrezzi, 5 pc
RVO1005 Ball Link Pliers Revolution Deluxe Kugelkopfzange Pince à rotules Pinze per attacchi a sfera
EFLAEC302 EC3 Battery Connector, Female (2) EC3 Akkukabel, Buchse (2) Prise EC3 femelle (2pc) EC3 Connettore femmina x batteria (2)
EFLAEC303 EC3 Device/Battery Connector, Male/Female EC3 Kabelsatz, Stecker/Buchse Prise EC3 male/femelle EC3 Connettore batteria maschio/
femmina
EFLB22003S30 11.1V 3S 30C 2200MAH Li-Po 11.1V 3S 30C 2200mAh LiPo 11.1V 3S 30C 2200MAH Li-Po 11.1V 3S 30C 2200MAH Li-Po
EFLB22003S50 11.1V 3S 50C 2200MAH Li-Po 11.1V 3S 50C 2200mAh LiPo 11.1V 3S 50C 2200MAH Li-Po 11.1V 3S 50C 2200MAH Li-Po
DYNC2005CA Prophet Sport LiPo 35W AC Charger Prophet Sport LiPo 35W AC Charger Chargeur Prophet Sport Li-Po 35W AC Profeta Sport LiPo 35W AC Charger
DYNC2010CA Prophet Sport Plus 50W AC DC Charger Dynamite Ladegerät Prophet SportPlus 50W AC/DC EU
Chargeur Prophet Sport Plus 50W ACDC
Caricabatterie Prophet Sport Plus 50W AC DC
SPMA3081 AS3X Programming Cable - Audio Interface
Spektrum Audio-Interface AS3X Emp-fänger Programmierkabel
Câble de programmation audio AS3X pour smartphone
Cavo di programmazione AS3X - Interfaccia audio
SPMA3065 AS3X Programming Cable - USB Interface
Spektrum USB-Interface AS3X Emp-fänger Programmierkabel
Câble de programmation USB AS3X pour PC
Cavo di programmazione AS3X - Interfaccia USB
EFLA111 Li-Po Cell Voltage Checker Li-Po Cell Voltage Checker Testeur de tension d’éléments Li-Po Voltmetro verifica batterie LiPo
DYN1405 Li-Po Charge Protection Bag, Large Dynamite LiPoCharge Protection Bag groß Sac de charge Li-Po, grand modèle Sacchetto grande di protezione per
carica LiPo
DYN1400 Li-Po Charge Protection Bag, Small Dynamite LiPoCharge Protection Bag klein Sac de charge Li-Po, petit modèle Sacchetto piccolo di protezione per
carica LiPoDXe DSMX 6-Channel Transmitter Spektrum DXe DSMX 6-Kanal Sender Emetteur DXe DSMX 6 voies DXe DSMX Trasmettitore 6 canaliDX6i DSMX 6-Channel Transmitter Spektrum DX6i DSMX 6-Kanal Sender Emetteur DX6i DSMX 6 voies DX6i DSMX Trasmettitore 6 canaliDX6 DSMX 6-Channel Transmitter Spektrum DX6 DSMX 6-Kanal Sender Emetteur DX6 DSMX 6 voies DX6 DSMX Trasmettitore 6 canaliDX6e DSMX 6-Channel Transmitter Spektrum DX6e DSMX 6-Kanal Sender Emetteur DX6e DSMX 6 voies DX6e DSMX Trasmettitore 6 canaliDX7G2 DSMX 7-Channel Transmitter Spektrum DX7 DSMX 7 Kanal Sender Emetteur DX7 DSMX 7 voies DX7 DSMX Trasmettitore 7 canaliDX8G2 DSMX 8-Channel Transmitter Spektrum DX8G2 DSMX 8 Kanal Sender Emetteur DX8G2 DSMX 8 voies DX8G2 DSMX Trasmettitore 8 canaliDX9 DSMX 9-Channel Transmitter Spektrum DX9 DSMX 9 Kanal Sender Emetteur DX9 DSMX 9 voies DX9 DSMX Trasmettitore 9 canaliDX18 DSMX 18-Channel Transmitter Spektrum DX18 DSMX 18 Kanal Sender Emetteur DX18 DSMX 18 voies DX18 DSMX Trasmettitore 18 canaliDX20 DSMX 20-Channel Transmitter Spektrum DX 20 DSMX 20 Kanal Sender Emetteur DX 20 DSMX 20 voies DX 20 DSMX Trasmettitore 20 canali
Created10/16 53879EFL4975, EFL4950
© 2016 Horizon Hobby, LLC. E-flite, Valiant, AS3X, DSM, DSM2, DSMX, the DSMX logo, Bind-N-Fly, BNF, the BNF logo, Plug-N-Play, SAFE, the SAFE logo, Z-Foam, ModelMatch, Dynamite, EC3,
Prophet and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
Futaba is a registered trademark of Futaba Denshi Kogyo Kabushiki Kaisha Corporation of Japan.
All other trademarks, service marks and logos are property of their respective owners.
US 9,056,667. US 8,672,726. Other patents pending.
http://www.e-fliterc.com/
Valiant™
