Embed Size (px)
Citation preview
SATAKE
E-D0371001-00-02 1
SATAKE INSTRUCTION MANUAL
VERTICAL RICE WHITENER
VTA5AA-TA
WARNING
• Do not carry out any operation, maintenance or inspection of the machine until you have read and well understood the contents of this instruction manual.
• Keep this manual at hand whenever any operation, maintenance or inspection of the machine is being carried out.
SATAKE (THAILAND) CO.,LTD.
SATAKE
2
CONTENT
1. LIMITED WARRANTY................................................................................................................. 4
2. SAFETY...................................................................................................................................... 5
2.1 Warning / Caution Types and Meanings ....................................................................... 6
2.2 General Instructions ...................................................................................................... 7
2.3 Special Precautions....................................................................................................... 9
2.4 Warning Stickers ......................................................................................................... 10
2.5 Location of Warning Stickers....................................................................................... 11
3. SPECIFICATIONS .................................................................................................................... 13
4. DIMENSIONS........................................................................................................................... 14
5. CONSTRUCTION..................................................................................................................... 15
6. INSTALLATION ........................................................................................................................ 16
6.1 Rigging Method of the Machine .................................................................................. 16
6.2 Confirmation of Levelness ........................................................................................... 17
6.3 Position setting ............................................................................................................ 17
6.4 Selection of Floor......................................................................................................... 18
6.5 Maintenance Space..................................................................................................... 18
6.6 Installation of Feeding Pipe ......................................................................................... 19
6.7 Motor Pulley Size ......................................................................................................... 19
6.8 Component Parts of Weight and Installation ............................................................... 20
6.9 Fitting the Motor........................................................................................................... 21
7. PREPARATION FOR OPERATION ........................................................................................... 22
7.1 Inspection of Belt Tension and Milling Chamber ......................................................... 22
7.2 Inspection in No-Load Operation ................................................................................ 22
7.3 Belt Tension Adjustment.............................................................................................. 23
7.5 Air Flow Rate Adjustment ............................................................................................ 24
7.6 Initial Adjustment of Abrasive Rollers .......................................................................... 24
8. OPERATION............................................................................................................................. 26
9. ADJUSTMENT OF RESISTANCE PLATE.................................................................................. 28
10. MAINTENANCE AND INSPECTION....................................................................................... 30
10.1 Periodical Check ..................................................................................................... 30
SATAKE
3
10.2 Periodical Clean ...................................................................................................... 30
10.3 Maintenance of Abrasive Roller Surface ................................................................. 31
10.4 Inspection................................................................................................................ 32
10.5 Rotation and Replacement of Screen...................................................................... 33
10.6 Replacement of Abrasive Roller .............................................................................. 35
10.7 Replacement of Resistance Plate............................................................................ 36
11. TROUBLESHOOTING............................................................................................................ 37
12. LIST OF CONSUMABLE PARTS ............................................................................................ 39
EMERGENCY ADDRESS AND TELEPHONE ............................................................................... 41
SATAKE
E-D0371002-00 4
1. LIMITED WARRANTY
The machine was produced under quality control and inspection. But, if there are any problems under normal use the limited warranty for the machine extends for the first year beginning on the date of purchase of the machine.
1. Please contact our agency or sales office to repair. If there is a problem within limited warranty period, We will repair for free (only under normal use condition). After the warranty period, repair fee would be billed.
2. It will be charged during limited warranty period following conditions.
(1) Damages & losses misuse of improper or operated installation with no care.
(2) Damages & losses unauthorized modification or unauthorized repair.
(3) Damages & losses because of disasters (fire, flood, storm and earthquake etc.), pollution, unusual voltage & damaged by sea air(rust).
(4) Damages & losses which you moved or dropped the machine after setting.
(5) Damages & losses which use of unauthorized spare parts or repair at unauthorized agency or factory.
3. We will supply parts of the machine for 7 years after stop of production. But within this period some special parts are exceptional.
4. Basically, We will stop to supply parts in 7 years after discontinued to produce. But if you have a request to order the parts, We will discuss about it. All warranty informations, machine features and specifications are subject to change without notice.
SATAKE
E-D0371003-00 5
2. SAFETY
WARNING Do not carry out any operation, maintenance or inspection until you have read and well understood the contents of this instruction manual.
• Keep this manual at hand for reference whenever any operation, maintenance or inspection of the machine is being carried out.
• When you operate, maintain or inspect the machine, you are requested to follow instructions and warnings as stipulated in this manual. If you have any questions or indistinct points, you should suspend operation of the machine or your work until you can clarify it with the Satake office listed at the end of this manual for inquiries about the machine.
• Satake shall not be responsible for any injury, loss or damage caused by failure to observe instructions stipulated in this manual, by misuse or modification without our permission.
This chapter describes the definition of hazard signal words as well as safety precautions to be observed at the time of operation, maintenance or inspection as detailed and classified in the “General Inspections” and “ Special Precautions.”
SATAKE
E-D0371004-00 6
2.1 Warning / Caution Types and Meanings Hazard warning in this instruction manual and warning stickers attached on the machine main body are classified into the following three kinds, depending on the degree of risk of accident.
Operator must recognize the importance of the warnings, and carefully follow the instructions given in this manual.
This shows potential hazard. If you do not follow this, WARNING there is some possibility of fatal or serious injury.
This shows potential hazard. If you do not follow this,
there is some possibility of middle or minor class CAUTION injury, damages of the equipment / machinery or
misconduct in material or product.
This is used for calling special attention to or NOTE adding emphasis to a certain information required
to be noticed.
SATAKE
E-D0371005-00 7
2.2 General Instructions
WARNING • The operator is supposed to pay attention to the following points to
ensure safety in operating, inspecting and serving the machine.
(1) Operator must contain long hair in a hair cover and neatly wear clothes and shoes
that are suitable for work. When carrying out any inspection or maintenance, wear appropriate protective gear such as helmet and safety shoes.
(2) Keep clean the surroundings and passages around the machine.
(3) Do not pour water over the machine. Water in the machine shorts the electric circuits, consequently causing the machine to break down.
(4) Do not fail to ground the machine in order to protect a person from being involved in electric accidents and to prevent fires from occurring due to current leaks.
(5) Never touch the live parts inside the machine after turning on power.
(6) Do not permit any person who has not been properly trained to operate or service the machine.
(7) Keep out any person other than those permitted by the operator. Never let children come close to the machine.
(8) Do not fail to inspect the machine before starting operation. When carrying out any inspection work, always power off and clearly indicate that the machine is under inspection or maintenance both in the control room and control panel at the work shop.
SATAKE
E-D0371006-00 8
(9) Always power off before inspection and maintenance and follow the appropriate lock out procedure. After the inspection, make sure that there are no tools left.
(10) Check for any looseness or damage on bolts, nuts and belts. Make sure to restore the cover after the checking.
(11) Check for any damages on power cords and wire cables. Also, check for any looseness or disconnection of connectors and plugs.
(12) Operate the machine with all covers attached. Do not attempt to remove any cover during the machine operation.
(13) Always stop the machine before greasing the driving part of the machine.
(14) Operator should well understand the power off procedure for a case of emergency.
(15) When working with two or more persons, each person must confirm communication with others before starting work.
SATAKE
E-D0371007-01 9
2.3 Special Precautions (1) Install the machine in a level and stable place. Unleveled and unstable installation
will cause vibration and poor performance of the machine.
(2) Do not operate, inspect or maintain the machine with any part that is not specified in this instruction manual.
(3) Keep sufficient working space around the machine.
(4) Before turning the power on, confirm the safety of the surroundings and passages around the machine.
(5) Handle the machine with care. Careless handling of the machine may lead to malfunction and failure of the machine.
(6) Keep alert to the machine, If any abnormality is found, stop the operation and check the machine to ensure safe operation.
(7) When using a ladder, it must be set in stable location.
(8) In case the machine is used in a dusty place, wear a dust-proof mask and goggles.
(9) If employees of a plant are unable to read or write, the owner of the plant must explicitly draw their attention to any existing hazards and must give them special instruction.
SATAKE
E-D0371008-00 10
2.4 Warning Stickers
! NOTE How to handle Warning Stickers
• Check if letters and illustration on the sticker are legible and if not, remove dirt on the sticker or replace it.
• Use cloth, water or cleanser to remove dirt. Do not use organic solvent or gasoline.
• In case the sticker is damaged, lost, or illegible, replace it with a new one.
This machine is provided with warning stickers on certain locations where a special precaution is required. It is important for operators to know the location and contents of each stickers and follow the instruction on the sticker to prevent accidents.
SATAKE
E-D0371009-00 11
2.5 Location of Warning Stickers
Fig. 2-1 Location of Warning Stickers (1)
SATAKE
299001524 T037213 T037214 T037213
T037214 T037212
SATAKE
E-D03710010-00 12
Fig. 2-2 Location of Warning Stickers (2)
299001524
T037213
T037213
299001524
SATAKE
E-D0371011-01 13
3. SPECIFICATIONS
Model VTA5AA-TA
Input Capacity 2 ~ 5.5 tons/hr.
Required Power 22kW, 4P or 30kW, 4P
Revolution of Main Shaft 570 ~ 660 RPM
Size of Bran Suction Outlet 8 inch Dia.
Air Volume & Static Pressure 30 m3 / min, -80 ~ -100 mmAq
Net Weight (without motor) Approx. 900 kgs
Noise Approx. 80 dB (A)
SATAKE
E-D0371012-00 14
4. DIMENSIONS
Unit : mm
Fig. 4-1
2x3 25 726
1052855815
135
1765
2309
815
4 inch
767227 6121719
8 inch
882
25
612
680
815
499
SATAKE
E-D0371013-00 15
5. CONSTRUCTION
Fig. 5-1
Abrasive rollerScreen
Motor
Inlet
Feed roller
Plate
WeightControl lever
Outlet
Lower front cover
V-beltV-pulley
SATAKE
E-D0371014-00 16
Plate
6. INSTALLATION
6.1 Rigging Method of the Machine
CAUTION • Use a wire having sufficient strength because the machine
weight without motor about 900 kgs.
• Use the four plates attached to the machine when transferring or installing the machine.
• Use great care not to damage the side cover, etc. when carrying and rigging work.
Fig. 6-1
SATAKE
E-D0371015-00 17
Check the levelness at the hatching portion.
815
69 612
25
815
767
6.2 Confirmation of Levelness
CAUTION • If the machine is not set horizontally, it may not be able to exhibit
its expected capability fully.
• Ensure the levelness of the machine and bolt it securely to the floor with bolts of M16.
Set the machine at the specified position and make sure that it is placed horizontally. If not, insert a liner at the position of bolt to adjust levelness of the machine. Then, securely fix the machine with the insulation pads for vibration.
6.3 Position setting
Unit : mm
Fig. 6-2 Position of Insulation Pads of Vibration
SATAKE
E-D0371016-00 18
500
Maintenance space
1500
1000 1000 1000
1000
6.4 Selection of Floor The net weight of main machine is approx. 900 kgs, and the weight of motor and motor base is approx. 270 kgs, so prepare the study-enough floor to install.
6.5 Maintenance Space
When installing the machine, allow enough space around the machine for maintenance and inspection jobs or passage as shown in Fig. 6.5. (The dimensions indicated are minimum).
Unit : mm
Fig. 6-3
SATAKE
E-0371017-00 19
To be able to separateat this connecting position.
6.6 Installation of Feeding Pipe Feeding pipe on the machine must be able to separate from the inlet of the machine for maintenance and inspection.
Fig. 6-4 Feeding Pipe Connection 6.7 Motor Pulley Size
Frequency Type of Pulley Machine (RPM)
50Hz, 4P ¿177, 5V-5 grooves 570
50Hz, 6P ¿267, 5V-5 grooves 570
60Hz, 4P ¿147, 5V-5 grooves 570
60Hz,6P ¿228, 5V-5 grooves 570
SATAKE
E-D0371018-00 20
6.8 Component Parts of Weight and Installation
! CAUTION • In case that the weight is easy to move on the control lever, it
may drop from the control lever when assembling it into the control lever and setting it in position, assemble with care.
6.8.1 Component parts of weight 6.8.2 Weight Installation
Fig. 6-5 Fig. 6-6 Weight assembly
• Fixed two levers on shaft as shown in Fig. 6-6.
• Install weight on lever.
Adjust spring as follow :
(1) Turn the screw clockwise to make the spring stronger, using a minus-screw driver.
(2) Slide the weight on the control lever to check the strength of spring.
(3) Turn the screw clockwise further when it is not strong enough, and counterclockwise when it is too strong.
SpringScrew
Steel ballWeight
SATAKE
SATAKE
SATAKE
SATAKE
E-D0371019-00 21
6.9 Fitting the Motor Make an opening on the safety cover when you fix the motor at site.
Fig. 6-7
Safety cover
Make an opening
Motor
SATAKE
E-D0371020-00 22
7. PREPARATION FOR OPERATION
! WARNING • Turn off the power switch and the breaker first before starting
examination of the rice milling chamber, and display sign board indicating “UNDER INSPECTION”.
• Turn the pulley with a hand slowly and examine the internal.
7.1 Inspection of Belt Tension and Milling Chamber
Remove the cover on the lower part of the machine, and conduct the following examination:
(1) Maintain proper tension of V-belt. Weak tension of V-belt will cause slip, and excessive tension may adversely affect the durability of bearing and the V-belt with resultant failures and accidents on the rice whitener.
(2) Inspect the inside of the rice milling chamber for any foreign matters such as bolts and nuts.
7.2 Inspection in No-Load Operation Operate the motor of the machine free from load, and check for any excessive heat on the bearing and any extraordinary vibration or noise on the machine. Make sure the rotating direction of the motor (clockwise seen from the top).
Fig. 7-1
Cover
SATAKE
E-D0371021-00 23
7.3 Belt Tension Adjustment
! WARNING • Turn off the power switch and the breaker at first before adjusting
the tension of belts and display a signboard notifying “UNDER INSPECTION”.
(1) Shorten the distance between axes.
Always shorten the distance between axes prior to attaching the belt. Give proper tension to the belt after completion of coupling of the belt.
(2) Maintain proper tension on V-belt. Belt tension is measured by the amount of load to cause 1.6 mm flexion per 100mm belt span when it is pulled down by a spring scale perpendicularly at the center of span. Tense the belt so that flexion load becomes 5.9 kgs to 8.7 kgs (7.6 kgs in case of renewal of re-tensioning). The optimum belt tension is such that the belt does not slip against maximum load being given to it and yet the belt is tensioned as possible. It is important to maintain belt tension between 5.9 kgs. and 8.7 kgs. Excessive tension exceeding 8.7 kgs may shorten durability of belts and bearings, while weaker tension less than 5.9 kgs may cause slips.
Fig. 7-2 Belt Tension
Span length1.6 mm depth flexionper 100 mm span
Load of flexion
SATAKE
E-D0371022-00 24
After a proper tension is given to the belt, run the machine for a few minutes and make sure that no excessive looseness of the belt exists. For a sample test is given to the belt, touch the pulley and the bearing by hand and check their temperatures.
• When the pulley is too hot : The belt tension may be too weak or the belt may be slipping.
• When the bearing part is too hot: :The tension of belt may be too tight. 7.5 Air Flow Rate Adjustment
! WARNING • Turn off the power switch before conducting initial setting of abrasive rollers.
Display an “UNDER INSPECTION” sign.
Adjust the air flow rate so that static pressure meter located on the back of the machine indicates -80~ -100mmAq at the fully closed state of secondary air inlet.
7.6 Initial Adjustment of Abrasive Rollers
! NOTE • The breaking-in operation is carried out only to remove useless abrasive grain
stuck to abrasive rollers and to sharpen the surface of abrasive rollers, but also to check for leakage of rice grain or bran. In addition, it is for eliminating anti-corrosive oil in the milling chamber. If the machine enters into a regular operation without a break-in operation, it may cause brans to stick to rollers surface, uneven rice whitening or accidents. Therefore, ensure to conduct a break-in operation before starting normal operation of the machine. Do not fail to carry out a break-in operation also when you operate the machine after a long absence or you have renewed the abrasive roller.
SATAKE
E-D0371023-00 25
Laying out a circulating line, and carry out breaking-in operation of the abrasive rollers using about 500kgs milled rice according to the following steps.
(1) Put the milled rice into the tank.
(2) Set smallest weights at the roots of control levers of the machine.
(3) Start the motor of the machine after starting the rice bran fan.
(4) Open the feeding valve gradually and adjust the rice flow rate. And operate finally at the rate of the flow stimulated in the specification.
(5) Make the weight of control lever of the machine to operate at the rated electric power.
(6) After about 10 minutes operation, discharge the rice grains outside of the machine.
SATAKE
E-D0371024-00 26
8. OPERATION
! WARNING • Do not open the cover during operation for safety.
• Never put your hand inside the machine without lock out the motor before checking. It shall take about 5 minutes for main shaft to stop completely after electric power is switched off.
! CAUTION • There is a possibility of tripping of the machine motor at starting
rice grain’s flow or at an abrupt adjustment of the weight.
(1) Turn on the rice-bran fan motor switch.
(2) Turn on the machine motor switch at the closed position of feed valve.
(3) Operate the machine at no load and check for unusual vibration or noise.
(4) Adjust the air-volume damper to make the static pressure of -65 mmAq (in case duct diameter is 8 inch).
(5) Set the smallest weight into the control lever, and open the feed valve.
(6) The rice milling chamber becomes full with rice grains, milled rice begins to be discharged, then the flow of electricity stabilizes. After that, adjust the weight while paying attention to the electric current not to exceed the rated value specified.
SATAKE
E-D0371025-00 27
When the machine motor has tripped and is unable to rotate in spite of attempting re-start up, or when the operator wishes to discharge remaining of rice grains from the machine, follow the procedure of restoration as described below:
Terminate the machine. (power off)
↓ Stop the suction. (or take off all the covers)
↓ Remove the cover of the residual grain discharging outlet located on the side of the machine and extract residual grains with a vacuum cleaner.
↓ If the rice grains are blocked in the milling chamber, and it is difficult to take them out, conduct inching-operations to loosen the cluster of rice grains and vacuum then out.
↓ Long-hour inching or repetitious inching may damage the magnetic contractor of motor.
If the motor will not run despite of any inching efforts, power off the motor and dismantle the machine to take out residual rice grains.
SATAKE
E-D0371026-00 28
9. ADJUSTMENT OF RESISTANCE PLATE
! WARNING • Turn off the power switch and the breaker first before starting
adjustment of plate, and display signboard indicating “UNDER INSPECTION”.
(1) Remove the cover for Frame (Ass’y) and side covers of the machine. Then, remove
the screens.
(2) Loosen lock nut, and adjust the clearance between abrasive roller and resistance plate by turning the knobs to be 6 mm by using gauge for clearance.
(3) Refer to Fig. 9-1, 9-2 and 9-3.
Fig. 9-1
SATAKE
SATAKE
SATAKE
SATAKE
E-D0371027-00 29
! NOTE • The clearance should be adjusted in accordance with the length
of rice grain.
Fig. 9-2
Fig. 9-3
Plate
Resistance plate
Gauge for clearance adjustment
(Clearance between abrasiveroller and resistance plate)6 mm
Resistance plate
SATAKE
E-D0371028-00 30
10. MAINTENANCE AND INSPECTION
! WARNING • Prior to cleaning or inspecting parts, turn off the power switch
and the breaker, and display an “UNDER INSPECTION” notice.
• Carry out inspection or maintenance work after you confirm a complete stop of the machine. Be careful especially because the main shaft of the machine keeps running for about 5 minutes even after the stop button is depressed.
10.1 Periodical Check Periodically check that fastening bolts are securely fastened. 10.2 Periodical Clean
The following positions are likely to gather bran, which should be cleaned on a regular basis.
Parts to be cleaned periodically Frequency
Outlet Once a day Bran discharge-way Once a week Chute Once a week Bran suction duct Once a month
SATAKE
E-D0371029-00 31
10.3 Maintenance of Abrasive Roller Surface
! NOTE • When it is necessary to rectify roller surface with dresser, contact
the distributor or sales shop. (1) When the roller surface is clogged with bran, remove them with a wire brush to clean
the surface.
(2) Rectify an indented surface or roughened grooves on the rollers with a dresser.
SATAKE
E-D0371030-00 32
10.4 Inspection
! CAUTION • Be sure to lock out the motor before checking. (It shall take about
5 minutes for main shaft to stop completely after electric power is switched off).
Item Content Frequency
• Run each equipment separately, and check for any unusual noise.
• Check for any unusual heat at bearings after 10 minutes or more of continued operation.
Bearing failures (noise / heat)
• Replace the bearing if any abnormal conditions are found.
Once a month
V-belt tension • The belt tension is judged appropriate when the belt deflects approximately 10 mm when pressed lightly with a finger.
Once a week
Screen wearing • It can be used until it breaks or deforms. Every 3 months Abrasive roller • Replace the abrasive roller when it lose 6~ 8 mm
in diameter. Every 3 months
Resistance plate • Replace it when the plate loose approximately 1/3 of its full width.
Every 3 months
SATAKE
E-D0371031-00 33
Frame ass'y
Hex.Nut(M30)
Fixture
FastenLoosen
10.5 Rotation and Replacement of Screen
① Remove the covers. (2 pieces)
Fig. 10-1 ② Loosen the Hex.Nut (M30)
and take off the fixture from the frame ass’y. (3 sets)
③ Remove the screen from the machine. (3 pieces)
Fig. 10-2
Side cover
SATAKE
E-D0371032-00 34
ScreenFrame
④ Remove the frame and the screen.
Fig. 10-3 ⑤ Turn the existing screen in
reverse of up and down and assemble the frame and its screen.
⑥ Assemble in reverse turn as above ④ , ③ , ② , ①
Fig. 10-4
SATAKE
E-D0371033-00 35
Spanner
Bolt
Washer
Abrasive roller
Feed roller
10.6 Replacement of Abrasive Roller After removing the screen.
① Remove the inlet section.
Fig. 10-5
② After taking off the bolt (left-thread) remove the feed roller and the abrasive rollers and plate from the main shaft one by one.
③ Assemble the new abrasive rollers.
④ Assemble in reverse turn as ② and ①
Fig. 10-6
SATAKE
E-D0371034-01 36
10.7 Replacement of Resistance Plate
After dismounting the frames (ass’y) from main body.
Fig. 10-7
(1) Loosen the Hex.socket head cap bolt and remove the resistance plate .
(2) Fix the new resistance plate by Hex. socket head cap bolt .
(3) Adjust the clearance between the abrasive roller and the resistance plate by turning
the knobs . Refer to Fig. 9-2 and 9-3.
(4) After finishing adjustment into desired clearance, fix resistance plate by turning the
knob .
(5) Adjust Support plate . (Must fit with body).
(6) Make the protection of looseness of resistance plate by fastening the Hex. nut .
(7) Assemble the remained part in reverse turn.
SATAKE
E-D0371035-00 37
11. TROUBLESHOOTING
! WARNING • Before maintenance the machine, isolate the machine from the power supply.
• Refit the safety cover after maintenance.
• If the troubles are not remedied even after taking measures following the below instructions, contract your nearby distributor. See the contact address of Satake group companies at the end of this manual.
Conditions of Failure Cause Action to Take
1. Insufficient flow rate. • Foreign matter in the feed Valve. → Remove the foreign matter. • Worn feed roller. → Replace the worn part. • Worn abrasive roller. → Replace the worn part. • Worn resistance plate. → Replace the worn plate. 2. A large amount of
worn milling roller. • A large amount of cracked
grains. → Check the material
condition. • Excessive flow rate. → Decrease the flow rate to
reduce the load. • Excessive weight resistance. → Decrease the resistance
load. • Worn resistance plate. → Replace the worn plate. • Indented surface or roughened. → Rectify the surface with the
dresser. • Grooves of abrasive roller. • Worn screen. → Replace the worn part.
SATAKE
E-D0371036-00 38
Conditions of Failure Cause Action to Take
• Worn milling roller. → Replace the worn part.
3. Rice temperature • Insufficient air flow rate. → Adjust the air flow rate. rise too high. • Inferior efficiency of screen,
abrasive of milling roller due to wear down.
→ Replace the worn part.
• Adhesion of bran to screen frame or clogging thereof.
→ Remove the bran stuck on the on the frame.
4. Insufficient whiteness.
• Inferior whiteness of the material grains.
→ Check the whiteness of the material.
• Wear down of screen, abrasive or milling roller, etc.
→ Replace the worn components.
• Adhesion of bran to screen flame or clogging thereof.
→ Remove the bran on the frame.
• Clogging of abrasive roller stuck with bran.
→ Remove the bran with wire brush.
• Worn resistance plate. → Replace the worn plate. 5. Inferior separation • Insufficient air flow rate. → Adjust the air flow rate. of bran. • Excessive feed rate of grains. → Restore a regular flow rate
of grains. • Excessive feed rate. → Clean the screen.
SATAKE
E-D0371037-00 39
12. LIST OF CONSUMABLE PARTS
Part No. & Part Name Q’ty Part No. & Part Name Q’ty
# 24P 261220340 261230570
# 30P 261220310 Resistance plate
# 36P 261220320
Abrasive roller 1 3
✻ # 30P is Standard
# 24P 261220440 261230530
# 30P 261220410 Plate
# 36P 261220420
Abrasive roller
✻ # 30P is Standard 8 6
SATAKE
E-D0371038-00 40
Part No. & Part Name Q’ty Part No. & Part Name Q’ty
261220160 261220495
Feed roller Plate
1 1
(80°, 0.9) 261230750 261221050
(80°, 1.0) 261230760 Case
(80°, 1.1) 261230830 1
(85°, 0.9) 261230800
(85°, 1.0) 261230820
(85°, 1.1) 261230810 3
Screen
261221360
Plate 1
SATAKE
E-D0371039-00 41
EMERGENCY ADDRESS AND TELEPHONE
Produced By SATAKE (THAILAND) CO.,LTD. 133 Moo 5 Bangkadi Industrial Park Tivanon Road Pathumthani 12000 Thailand Tel. 66-2-501-1180 Fax. 66-2-501-1188 E-Mail: [email protected] Home Page : www.sataketh.com Sold By SATAKE CORPORATION 2-30 Saijo Nishihonmachi Higashi-Hiroshima-Shi Hiroshima 739-8602 Japan Tel. 81-824-20-8539 Fax. 81-824-20-0865 E-Mail: [email protected]
SATAKE
E-D0371040-00 42
SATAKE (THAILAND) CO., LTD.
133 Moo 5 Bangkadi Industrial Park
Tivanon Road Pathumthani 1200 Thailand
Tel. 66-2-501-1180
Fax. 66-2-501-1188
E-Mail: [email protected]
Home Page : www.sataketh.com
